Documente Academic
Documente Profesional
Documente Cultură
Feature
■ Superior output power capability:
– 4 x 50 W/4 Ω max.
– 4 x 45 W/4 Ω EIAJ
– 4 x 30 W/4 Ω @ 14.4 V, 1 kHz, 10 %
( s )
– 4 x 80 W/2 Ω max.
– 4 x 77 W/2 Ω EIAJ
Flexiwatt27 (vertical)
u ct
– 4 x 55 W/2 Ω @ 14.4 V, 1 kHz, 10 %
o d
■ Multipower BCD technology ■
limiter
P r
Overrating chip temperature with soft thermal
■
s Fortuitous open GND
Reversed battery
■ Standby function
O
)-
■ ESD
■ Mute function
■
(
Automute at min. supply voltage detection
t s Description
■ Low external component count:
c
du
The TDA7560A is a breakthrough BCD (Bipolar /
– Internally fixed gain (26 dB)
CMOS / DMOS) technology class AB audio power
r o
– No external compensation amplifier in Flexiwatt 27 package designed for
■
e P
– No bootstrap capacitors
On board 0.35 A high side driver
high power car radio.
■
s o
Output short circuit to GND, to VS, across the
swing which, combined with high output current
and minimized saturation losses sets new power
O
■
b load
Very inductive loads
references in the car-radio field, with unparalleled
distortion performances.
Contents
2 Electrical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.1 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.2 Thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.3 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.4 Standard test and application circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
( s )
ct
2.5 Electrical characteristics curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
d u
3
o
Application hints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
r
3.1
P
SVR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
e
3.2
3.3 l e t
Input stage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Standby and muting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.4 s o
DC offset detector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.5
O b
Heatsink definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
) -
4
(s
Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
c t
5
d u
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
r o
e P
l e t
s o
O b
2/15
TDA7560A List of tables
List of tables
( s )
u ct
o d
P r
e t e
o l
b s
- O
(s )
c t
d u
r o
e P
l e t
s o
O b
3/15
List of figure TDA7560A
List of figure
4/15
TDA7560A Block and pin connection diagrams
Vcc1 Vcc2
470μF 100nF
ST-BY
OFF DET
MUTE HSD HSD/OFF DET
OUT1+
IN1 OUT1-
)
0.1μF PW-GND
OUT2+
( s
IN2
0.1μF
OUT2-
u
PW-GND ct
o d
OUT3+
Pr
IN3 OUT3-
0.1μF PW-GND
e t e OUT4+
IN4
l OUT4-
so
0.1μF PW-GND
AC-GND
0.47μF 47μF
SVR
O b TAB S-GND
)-
D03AU1467
D03AU1468
5/15
Electrical specifications TDA7560A
2 Electrical specifications
( s )
ct
IO Repetitive (duty cycle 10 % at f = 10 Hz) 9 A
Non repetitive (t = 100 µs) 10 A
Ptot Power dissipation Tcase = 70 °C
d u
85 W
o
Pr
Tj Junction temperature 150 °C
Tstg Storage temperature -55 to 150 °C
e t e
2.2 Thermal data
s ol
Table 3. Thermal data
O b
Symbol
( s )-
Parameter Value Unit
Rth j-case
c t
Thermal resistance junction to case Max. 1 °C/W
d u
2.3
o
Electrical characteristics
r
Table 4. P
Electrical characteristics
e
l e t
(Refer to the test and application diagram, VS = 13.2 V; RL = 4 Ω; Rg = 600 Ω; f = 1 kHz;
Tamb = 25 °C; unless otherwise specified).
o
bs
Symbol Parameter Test condition Min. Typ. Max. Unit
RL = ∞
O Iq1
VOS
Quiescent current
Output offset voltage Play Mode
80 200 320
±50
mA
mV
During mute ON/OFF output
dVOS ±60 mV
offset voltage
Gv Voltage gain 25 26 27 dB
dGv Channel gain unbalance ±1 dB
VS = 13.2 V; THD = 10 % 23 25
VS = 13.2 V; THD = 1 % 16 19
Po Output power W
VS = 14.4 V; THD = 10 % 28 30
VS = 14.4 V; THD = 1 % 20 23
6/15
TDA7560A Electrical specifications
VS = 13.2 V; THD = 10 %, 2 Ω 42 45
VS = 13.2 V; THD = 1 %, 2 Ω 32 34
Po Output power W
VS = 14.4 V; THD = 10 %, 2 Ω 50 55
VS = 14.4 V; THD = 1 %, 2 Ω 40 43
VS = 13.7 V; RL = 4 Ω 41 45
Po EIAJ EIAJ output power(1) W
VS = 13.7 V; RL = 2 Ω 77
VS = 14.4 V; RL = 4 Ω
(s)
43 50
Po max. Max. output power(1) W
VS = 14.4 V; RL = 2 Ω 75 80
Po = 4 W 0.006
c t
0.02
THD Distortion
Po = 15 W; RL = 2 Ω 0.015
d u 0.03
%
CT Cross talk
O b
f = 1 kHz PO = 4 W
f = 10 kHz PO = 4 W
60
50
70
60
-
-
dB
) -
VST-BY = 1.5V 20
(s
ISB Standby current consumption μA
c t VST-BY = 0 V 10
μA
Ipin5 ST-BY pin current
u VST-BY = 1.5 V to 3.5 V ±10
od
VSB out Standby out threshold voltage (Amp: ON) 3.5 V
Pr
VSB in Standby in threshold voltage (Amp: OFF) 1.5 V
AM
e t e
Mute attenuation POref = 4W 80 90 dB
ol
VM out Mute out threshold voltage (Amp: Play) 3.5 V
VM in Mute in threshold voltage (Amp: Mute) 1.5 V
b s (Amp: Mute)
HSD section
7/15
Electrical specifications TDA7560A
O b C7
2200μF
)-
Vcc1-2 Vcc3-4
R1 7 21
ST-BY
10K
t (
C9
s
1μF
5 10
9 OUT1
MUTE
u
R2
47K c C10
23
8
o d C1
1μF 6
3 OUT2
P r IN1
0.1μF
12
4
e IN2 13 18
let
C2 0.1μF 19 OUT3
20
o
IN3 16
s
C3 0.1μF
22
Ob IN4
C4 0.1μF S-GND
15
14
17 11 26 1, 27
25
24
2 OFF DET
OUT4
8/15
TDA7560A Electrical specifications
Id (mA) Po (W)
240 80
75 Po-max
Vi = 0
70
220 65
RL = 4 Ohm 60 RL= 4 Ohm
55 f= 1 KHz
200 50 THD= 10 %
45
40
180 35
30
25
( s )
THD= 1 %
ct
160 20
15
140
8 10 12 14 16 18
10
5
8 9 10 11 12 13 14
d u 15 16 17 18
Vs (V)
r Vs (V)
o
Figure 6. Output power vs. supply voltage Figure 7. P
Distortion vs. output power
e
(RL = 2Ω)
l t
(RL = 4Ω)
e
130
Po (W)
s 10
THD (%)
o
120
110
100
Po-max
O b Vs= 14.4 V
90
80
RL= 2 Ohm
f= 1 KHz
) -
THD= 10 %
1 RL = 4 Ohm
(s
f = 10 KHz
70
60
50
c t 0.1
40
u THD= 1 %
od
0.01 f = 1 KHz
30
20
10
8 9 10 11
P r12 13 14 15 16 17 18 0.001
0.1 1 10
e t e Vs (V) Po (W)
Figure 8.
o l Distortion vs. output power Figure 9. Distortion vs. frequency (RL = 4Ω)
b s (RL = 2Ω)
O 10
THD (%)
10
THD (%)
Vs= 14.4 V
1 RL = 2 Ohm 1 Vs = 14.4 V
RL = 4 Ohm
f = 10 KHz Po = 4 W
0.1 0.1
0.001 0.001
0.1 1 10 10 100 1000 10000
Po (W) f (Hz)
9/15
Electrical specifications TDA7560A
Figure 10. Distortion vs. frequency (RL = 2Ω) Figure 11. Crosstalk vs. frequency
80
1 Vs = 14.4 V
RL = 2 Ohm 70
Po = 8 W
60
0.1
50 RL = 4 Ohm
Po = 4 W
40 Rg = 600 Ohm
0.01
30
( s )
ct
0.001 20
10 100 1000 10000 10 100 1000 10000
f (Hz) f (Hz)
d u
Figure 12. Supply voltage rejection vs.
r
Figure 13. Output attenuation vs. supply
o
frequency voltage
e P
100
SVR (dB)
l e t
OUT ATTN (dB)
90 0
o
bs
RL = 4 Ohm
80 Po= 4 W ref.
-20
70
- O -40
60
50
( s )
t
Rg= 600 Ohm -60
40 Vripple= 1 Vrms
c
du
-80
30
20
10 100
r o 1000 10000
-100
5 6 7
Vs (V)
8 9 10
e P f (Hz)
l e t
Figure 14. Output noise vs. source resistance Figure 15. Power dissipation and efficiency vs.
output power (sine-wave operation)
s o Ptot (W)
b En (uV) n (%)
130 90 90
O 120
110
100
Vs= 14.4 V
RL= 4 Ohm
80
70
Vs= 13.2 V
RL= 4 x 4 Ohm
n 80
70
60 f= 1 KHz SINE
60
90
50 50
80
70 40 40
22-22 KHz lin.
60 30 30
Ptot
50 20 20
40 "A" wgtd
10 10
30
0 0
20 0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30
1 10 100 1000 10000 100000
Rg (Ohm) Po (W)
10/15
TDA7560A Electrical specifications
Figure 16. Power dissipation vs. output power Figure 17. Power dissipation vs. output power
(music/speech simulation); (music/speech simulation);
RL = 4 x 4Ω RL = 4 x 2Ω
10
20
15
( s )
ct
10
du
5 5
0 1 2 3 4 5 6 0 2 4 6 8 10
Po (W) Po (W)
r o
Figure 18. ITU R-ARM frequency response,
weighting filter for transient pop
e P
e t
ol
Output attenuation (dB)
10
0
b s
-10
- O
-20
(s )
-30
c t
-40
d u
-50
r o
10 100
e P 1000
Hz
10000 100000
AC00343
l e t
s o
O b
11/15
Application hints TDA7560A
3 Application hints
(ref. to the circuit of Figure 3)
3.1 SVR
Besides its contribution to the ripple rejection, the SVR capacitor governs the turn ON/OFF
time sequence and, consequently, plays an essential role in the pop optimization during
ON/OFF transients.To conveniently serve both needs, ITS MINIMUM RECOMMENDED
VALUE IS 10 µF.
( s )
ct
The TDA7560A's inputs are ground-compatible and can stand very high input signals
(±8 Vpk) without any performances degradation.
r o
3.3 Standby and muting
e P
l e t
Standby and Muting facilities are both CMOS-compatible. In absence of true CMOS ports or
s o
microprocessors, a direct connection to Vs of these two pins is admissible but a 470 kOhm
equivalent resistance should be present between the power supply and the muting and
ST-BY pins.
O b
R-C cells have always to be used in order to smooth down the transitions for preventing any
audible transient noises.
) -
(s
About the standby, the time constant to be assigned in order to obtain a virtually pop-free
t
transition has to be slower than 2.5 V/ms.
c
3.4 d u
DC offset detector
r o
P
The TDA7560A integrates a DC offset detector to avoid that an anomalous DC offset on the
ete
inputs of the amplifier may be multiplied by the gain and result in a dangerous large offset on
the outputs which may lead to speakers damage for overheating. The feature is enabled by
o l the MUTE pin (according to Table 4) and works with the amplifier unmuted and with no
O –
–
Pin 2 (always enabled)
Pin 26. Only enabled if Vmute (pin23) is set higher than 8V. If not (Vmute < 6 V)
pin 26 will revert to the original HSD function
12/15
TDA7560A Package information
4 Package information
)
mm inch
DIM.
MIN. TYP. MAX. MIN. TYP. MAX.
A 4.45 4.50 4.65 0.175 0.177 0.183 OUTLINE AND
( s
ct
B 1.80 1.90 2.00 0.070 0.074 0.079 MECHANICAL DATA
C 1.40 0.055
D 0.75 0.90 1.05 0.029 0.035 0.041
E
F (1)
0.37 0.39 0.42
0.57
0.014 0.015 0.016
0.022
d u
o
G 0.80 1.00 1.20 0.031 0.040 0.047
G1
H (2)
H1
H2
25.75
28.90
26.00
29.23
17.00
12.80
26.25
29.30
1.014
1.139
1.023
1.150
0.669
0.503
1.033
1.153
P r
H3
L (2) 22.07
0.80
22.47 22.87 0.869
0.031
0.884 0.904
e t e
L1
L2 (2)
L3
18.57
15.50
7.70
18.97
15.70
7.85
19.37
15.90
7.95
0.731
0.610
0.303
0.747
0.618
0.309
0.762
0.626
0.313
o l
L4
L5
M 3.70
5
3.5
4.00 4.30 0.145
0.197
0.138
0.157
b s
0.169
M1
N
O
3.60 4.00
2.20
2
4.40 0.142
-
0.157
0.086
0.079 O
0.173
R
R1
1.70
0.5
(s ) 0.067
0.02
t
R2 0.3 0.12
R3 1.25 0.049
R4
V
0.50
u c 5˚ (Typ.)
0.019
Flexiwatt27 (vertical)
V1
V2
o d 3˚ (Typ.)
20˚ (Typ.)
r
V3 45˚ (Typ.)
(1): dam-bar protusion not included
l e t V
C
o
bs
B
V
H
O V3
H3
H1
H2 A
O
R3
R4
L4
V1
R2
N
L2
R
L L1
V1
L3
V2
R2 D
R1
L5 R1 R1
Pin 1
E
G G1 F
FLEX27ME
M M1
7139011
13/15
Revision history TDA7560A
5 Revision history
( s )
Modified max. values of the VOS and THD parameter in Table 4:
ct
07-Nov-2008 3
Electrical characteristics.
d u
r o
e P
l e t
s o
O b
) -
c t (s
du
r o
e P
l e t
s o
O b
14/15
TDA7560A
( s )
ct
Please Read Carefully:
d u
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
r o
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
e P
e t
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
l
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
s o
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
b
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
O
third party products or services or any intellectual property contained therein.
) -
(s
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
t
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
c
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
u
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
d
r o
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZE REPRESENTATIVE OF ST, ST PRODUCTS ARE NOT DESIGNED,
AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS,
e P
NOR IN PRODUCTS OR SYSTEMS, WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR
SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE.
l e t
s o
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
O b
liability of ST.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
15/15