Documente Academic
Documente Profesional
Documente Cultură
SiPass® integrated
3 LCD Messages......................................................................................... 7
3.1 Language Support for LCD Messages...................................................... 9
4 Keyword index....................................................................................... 10
3
Building Technologies A6V10265089
02.2018
4
Building Technologies A6V10265089
02.2018
Introduction
1 Introduction
SiPass integrated constantly innovates to provide improved security to customers,
while enhancing their access flexibility options on sites.
As a result, SiPass integrated can support the iClass HADP OSDP Reader in the
HID mode. This will provide sites with a bi-directional means of communication, us-
ing Card Data and Messages that can be displayed on the reader’s LCD screen.
Before configuring this reader with SiPass integrated, it is recommended that the
user / operator read this document. It contains information on the following:
5
Building Technologies A6V10265089
02.2018
Prerequisites to Reader Configuration
By configuring the iClass OSDP as the Reader Technology, and iClass as the
Card Technology in the FLN Configuration dialog of SiPass integrated, or
– Using the standalone ACC and FLN Configuration Tool:
By selecting the iClass OSDP as the Reader Technology and iClass as the Card
Technology in the standalone ACC and FLN Configuration Tool
6
Building Technologies A6V10265089
02.2018
LCD Messages
3 LCD Messages
The table in the section details all the available LCD messages that will be
displayed on the iClass Reader when the respective ACC Events occur.
7
Building Technologies A6V10265089
02.2018
LCD Messages
Hard APB Error Corresponding Card Status Audit Trail Message: 5 sec
Access denied – Hard APB error, or
Access denied – Hard Perimeter Violation
Area Capacity Limit Error Corresponding Card Status Audit Trail Message: 5 sec
Access Denied – Capacity Full, or
Access Denied – Workgroup Capacity Full
Area Lockout Corresponding Card Status Audit Trail Message: 5 sec
Access Denied – Intrusion Area Armed
Dual Custody Error Corresponding Card Status Audit Trail Message: 5 sec
Invalid Dual Custody
Invalid Daily Code Corresponds with the following Access Point 5 sec
Audit Trail message:
Invalid Daily Code
Door Unlocked Corresponds with the following Output Point Displayed indefinitely
Audit Trail message for an Output Point that is until door is locked
associated with a given reader:
Unlocked
Door Blocked Corresponds with a Block Door manual Displayed indefinitely
command received, or until door is
unblocked
CBET action triggered
Enter PIN LCD message appears when a card is presented PIN Timeout Period
at an Access Point configured for the Card + PIN
operation mode
Access Denied LCD message appears when Host Verification 5 sec
Access is denied by the host
Reader Disabled Corresponds with the following Card Status Audit 5 sec
Trail messages:
Access point disabled
Waiting for 2nd Card LCD messages appears after the 1st card badge Dual Custody
Badge has been verified at the access point with Dual Timeout Period
Custody activated
Reader Disabled Corresponds with the following Card Status Audit 5 sec
Temporarily Trail messages:
Turnstile In Use- - Reader Disabled, or
Door Interlocking in Progress – Reader
Disabled
8
Building Technologies A6V10265089
02.2018
LCD Messages
– Spanish
– German
– Italian
– French
9
Building Technologies A6V10265089
02.2018
Keyword index
4 Keyword index
A L
ACC and FLN Configuration Tool, 6 LCD messages, 7
F P
FLN Configuration dialog, 6 Prerequisites, 5
H R
HADP OSDP, 6 RS485 Personality Module, 6
HID Config Card, 6
10
Building Technologies A6V10265089
02.2018
Issued by © Siemens Switzerland Ltd, 2018
Siemens Switzerland Ltd Technical specifications and availability subject to change without notice.
Building Technologies Division
International Headquarters
Gubelstrasse 22
CH-6301 Zug
Tel. +41 41-724 24 24
www.siemens.com/buildingtechnologies