Documente Academic
Documente Profesional
Documente Cultură
2015
1. PURPOSE
ATPV 24Cal/cm2 2. ADJUSTMENTS
3. STORAGE & TRANSPORTATION
HAF 91% 4. CLEANING
5. ROUTINE TESTS AND INSPECTION BEFORE USE
6. MARKING
14. WARRANTY
Type I
ANSI/ISEA Z89.1 Class G
EN 50365:2002
EN 397:2012+A1:2012
1. PURPOSE Do not use paints, acids or any self-adhesive labels unauthorized by the
manufacturer.
SECRA helmet protects upper head area against injuries from falling objects, 3. STORAGE & TRANSPORTATION: The helmet must be stored and shipped in a
splashes of molten metal and electric shock by preventing electric current flow through separate transport bag. Store far from sources of heat. Protect against mechanical
the head, as well as against electric arc hazards. It is particularly recommended as damage and sunlight (UV). Do not place the helmet directly next to room and vehicle
personal protective equipment in live line working. windows.
2. ADJUSTMENTS 4. CLEANING: Clean with water and soap. Dry after cleaning. Replace sweat cloth
if used up.
The helmet must properly fit the head. To adjust the helmet to the head circumference,
set the chinstrap length and the helmet height accordingly. The helmet can be 5. ROUTINE TESTS AND INSPECTION BEFORE USE:
adjusted stepwise every 2 mm to fit the scalp within the range of 53 – 63 cm, and is The inspection should be done each time before commencement of work. The
equipped with a two-step adjustment of the helmet height. inspection is aimed at checking:
o lack of visible defects in the shell of a helmet
HELMET SIZE ADJUSTMENT HELMET HEIGHT ADJUSTMENT o correctness of operation of head girth regulation
o correctness of operation of under-chin fastening strap
o service life
Damaged (mechanical damage of the shell or incorrect operation of head girth
regulation or under-chin fastening strap) or dirty helmet cannot be used for live
1 working. Dry thoroughly the wet helmet before use. Pay attention to the service life
of the helmet, which is 48 months from the date of production. After this period the
2 helmet should be taken out of service and utilized.
The helmet is executed according to ANSI/ISEA Z89.1, EN 397:2012 and
EN 50365:2002 standards.
6. MARKING:
label stamped on the helmet shell:
Position of the clip: (1) shallow, (2)
loosen (1) or tighten (2) -live line working symbol.
deep, EN 50365:2002: -reference standard „Electrically insulating helmets for use on low voltage
CHINSTRAP CLIP installations”
class 0: -electric class for systems with voltage rating up to 1,000V AC, and 1,500V DC
serial no. -for example 015
CE 1437: - conformity marking acc. to Directive 89 / 686 / EEC and notified body no.
SECRA: - symbol (name) of the product
EN 397:2012+A1:2012 - reference standard „Industrial safety helmets”
53-63cm: - adjustment range - head circumference
HUBIX: - manufacturer
-30°C: - very low temperature (down to –30°C)
440 Vac: - electrical insulation
MM: - molten metal splash
Pull away the clip (1), insert the strap piece (2) into the snap fastener of the strap, and LD: - lateral deformation
release clip. Working life of the helmet is 48 months from the date of manufacture. ANSI/ISEA Z89.1-2014 -reference standard “American National Standard for Industrial Head
DISPOSE OF THE HELMET IN CASE OF SURGE, CRACKS OR DAMAGE. None Protection”
of the helmet elements can be removed or tampered with.
Type I - intended to reduce the force of impact from a blow only to the top of the head 9. CLEANING
Class G - intended to reduce the danger of contact with low voltage conductors
Clean with water and soap. Dry after cleaning. The shield can be damaged by
date of manufacture (quarter / year) aggressive chemical substances. Do not use solvents and detergents for
date of disposal (quarter / year)
cleaning. To clean the surface of visor use microfiber cloth.
Working life of the face shield is 48 months from the date of manufacture. Replace
the face shield in case of: cracks, puncture, scratches, and fogging. The
manufacturer guarantees comprehensive servicing of the delivered equipment.
Sweatbands are fastened to the main and rear harness with a hook and loop fastener.
Pull the sweatband carefully to separate it from the harness. Replace worn
sweatbands. 14. WARRANTY
13.2 HEAD HARNESS
head harness catch
The manufacturer’s warranty is 24 months, starting from the date of purchase, it
doesn`t cover if used not on regular bases, altered and modified, improperly stored,
damage by accident, other causes beyond our reasonable.