Documente Academic
Documente Profesional
Documente Cultură
E1 Open circuit / short circuit of temperature An error occurs if the connection is interrupted with An error occurs if the connection with a temperature • Open circuit / short circuit of temperature sensor.
sensor. a temperature sensor or a short circuit the sensor is interrupted or there is short circuit • Check NTC sensor, replacement.
temperature sensor. Washing program ends without between the terminals of the temperature sensor. • Check connectors, cables to the NTC sensor.
LED indication: All LEDs blink repeatedly heating, an error is displayed after completing the Washing program ends without heating, the error is
1x (½ sec. ON, ½ sec. OFF) and 5 program. shown at the end of the program.
second PAUSE.
LED:E1 LCD:ERROR 1
E2 Open circuit of switch with door lock. PTC - bimetal lock • Check the door. Check door switches, connectors, cables and motor
• Close the door and press START. If the machine stator windings.
LED indication - door open: An error occurs if the connection to the door switch does not start, close the door again harder and
LED1 and LED2 blink repeatedly 2x (½ is broken or motor winding interrupted (applies to press START.
sec. ON, ½ sec. OFF) and 5 second universal motor). Washing program stops and an
PAUSE. error is displayed.
LED:E2 LCD:ERROR 2
MDL magnetic lock.
All LEDs blink repeatedly 22x (½ sec. Washing program stops and an error is displayed.
ON, ½ sec. OFF) and 5 second PAUSE.
LED:E22 LCD:ERROR 22
E23 MDL magnetic lock. The door is closed - Contact C is checked at all • Check the door. • Check door, lock and control unit.
times. • Check the water, drain the water. • Check the water, drain the water.
Door closed, lock not released.
The error occurs at the end of the program, doors
LED indication: are closed, can not be opened.
•Check if transport
•Check if transport brackets were
brackets were removed.. •Check
removed.. •Check levelling, positioning of
levelling, positioning of the appliance..
the appliance.. •Checking the
The appliance The appliance trembles, •Checking the distribution of laundry in
moves or vibrates moves or vibrates during distribution of laundry the drum, especially if it
during operation.. operation. in the drum, especially is little laundry. •Check
if it is little laundry. the voltage (too low
•Check the voltage (too voltage).
low voltage). •Check appliance
housing.
Overdosing of washing
Overdosing of washing
agent.. Washing agent
agent.. Washing agent
shall be added in
shall be added in
compliance with the
Excessive foaming compliance with the
instructions (consider
during washing instructions (consider
Excessive foaming during water hardness and
program. water hardness and
washing program. laundry dirtiness) . Use
laundry dirtiness) . Use
the washing agents
the washing agents
intended for use in
intended for use in
washing machines.
washing machines.
Detergent Water is dripping from the • Clean the detergent • Check appliance
dispenser is detergent dispenser. dispenser.. • Detergent layout, • tilt slightly
leaking. dispenser compartment backwards, • Clean the
closed during operation. detergent dispenser.
E4 Opened If the waching program is • The motor is not • The drum / motor of
tachogenerator active and the control unit running. • Tacho- the appliance is not
terminals or short of the electric motor does generator open circuit turning. • Check electric
circuit. LED not receive tacho- or motor windings short motor, tacho-generator,
indication: All LEDs generator signal for the circuit. brushes, coils,
blink repeatedly 4x first time, process is connectors and cable
(½ sec. ON, ½ sec. paused for 1 minute. This set.
OFF) and 5 second is repeated 30 times. The
PAUSE. LED:E4 count is If the motor in the
LCD:ERROR 4 31 experiment runs, the
fault reset, otherwise the
washing is suspended. If
the water temperature is
higher than 60 ° C, then
the machine filled with
cold water for 30 seconds.
Followed by a two-minute
water pumping. The
program stops and an
error is displayed. NOTE:
E2 error may appear if the
motor thermal switch
activates or if the program
is restarted after
displaying an error E4.
E7 Water level not The error occurs if water • Pump clogged or • Check the pump. •
falling under level 1 level does not fall below damaged. • Check the Check hose, drain.
(pressure switch the hydrostat level after filter, clean. • Check
level). LED draining. When an error wall siphon, clean it.
indication: All LEDs occurs for the first time in
blink repeatedly 7x the washing program will
(½ sec. ON, ½ sec. automatically repeat
OFF) and 5 second draining step. When the
PAUSE. LED:E7 error occurs a second time
LCD:ERROR 7 in a row, the washing
program stops and
displays an error. To
continue the program it is
necessary to press the
Start button. If an error
occurs for third time, the
washing program stops,
the error is displayed and
the program can no longer
be activated.
Maximum spinning
An error occurs at the end
revolutions not
of the spin cycle in the
reached. LED
test program if centrifuge
indication: All LEDs
is more than 200V/min or
E8 blink repeatedly 8x Check motor / voltages.
20% less than that
(½ sec. ON, ½ sec.
prescribed. The error only
OFF) and 5 second
appears after the test
PAUSE. LED:E8
program.
LCD:ERROR 8
Overflow is included in
case when pump is
powered via contact on
hydrostat. The pump is
activated directly via the
Overflow. LED
contact hydrostat. This
indication: All LEDs
happens in the case of
blink repeatedly
electrical failure or • Check el. valve. •
11x (½ sec. ON, ½
E11 hydrostat valve caps Close the inlet valve. Check hydrostat,
sec. OFF) and 5
blockage. If the error is hydrostat caps.
second PAUSE.
repeated 5 times (every
LED:E11
mistake takes 2 minutes),
LCD:ERROR 11
then the control unit turns
off all valves (including
Aqua stop) and stops the
program. Error is
displayed.
gorenjegroup 4.10.2016
SERVICE INSTRUCTIONS
During control unit replacement configuration process must be done first ( to define appliance parameter).
Quit configuration, keep appliance on selected program.
Then switch OFF the washing machine (selector on position 0).
Then run test program and define motor alternative (use table 1).
At the service intervention during control unit replacement it’s necessary to define out motor type build in
appliance ( run test program or see motor label) and set motor alternative in test program.
BASIC
CLASSIC
EXCLUSIVE 1
EXCLUSIVE 2
In all 4 main HW variants (Basic, Classic, Exclusive1 and Exclusive2) we will use button S3 as “Next”
and button S2 as “Previous” to go between different steps of configuration “on-board programming process”.
Button “S2” (in the first step) quit configuration.
Button “S3” (in the last step) has function saves the settings and quit.
In Basic HW variant we will use for indication of each step unique combination of LEDs 15 – 24.
In Classic HW variant we will use for indication of each step only LED display with message “Sx”, where “x”
will be the step number
In Exclusive 1 and Exclusive 2 HW variant we will use for indication of each step only LCD display with
message “Sx”, where “x” will be the step number.
SET
SELECT DRUM LOAD
Position 1 - 5kg
Position 2 - 6kg
Position 3 - 7kg
Position 4 - 8kg
Position 5 -15 - 9kg
where
PR - Prewash
HL – HalfLoad
WP – Water plus
SG – SmartGrid
SC - Selfcleaning
Service contol unit is alternative for more control units in serial production.
For correct washing machine operation suitable configuration must be done.
After
MOTOR Regular Drum
Type Code Sales Load Alternative
PRODUCER production speed
Service
6, 7
HXG 30 154542 YES YES 600
kg
1
Welling UM 6, 7 A
HXG 40 154543 YES YES 800
kg
A1
6, 7
HXG52A54.04 154545 YES YES 1300-1400
kg
6, 7
HXG52-AL 413600 YES YES 1000-1200
kg
1BA6745-0701
ATLANT 469169 YES / SLIM 800-1200
PL.CA
6, 7 2
Selni UM W35 267980 YES YES 600
kg
B
6, 7
MCA61/64-148/KT16 273680 YES YES 1300-1400
kg
MCA61/64-148/KT18 6, 7
587548 YES YES 1000-1200
AL kg
MCA 61/64-
475799 YES YES SLIM 1300-1400
148/KT20 AL
6, 7
MCA61 KT22-60Hz 521191 YES YES 1300-1400
kg
6, 7
MCA61 KT21-60Hz 521211 YES YES 1000-1200
kg
6, 7
C51.05.47.07 280350 YES YES 600
kg 3
Ana Imep
UM
C
C51.05.52.05 348870 YES YES SLIM 800-1200
A3
6, 7
Nidec UM T63-G01 470070 YES YES 1000-1200
kg
6, 7
WU112U40 497151 YES / 800
kg
WU126 T65-G02
521212 YES YES 8 kg 1300-1400
60Hz
6, 7
T63 587540 / / 1000-1200
kg
6, 7
P33 291266 / / 1300-1400
kg
Selni UM
P71 387969 / / 8 kg 1000-1200
Test program
Washing machines with universal motor (UM) set motor alternative during test program
process according table 1 (A1=A=1 ali A2=B=2 ali A3=C=3).
Washing machines with brushless permanent magnet motor (BM) set motor alternative during
test program process A1 ali A ali 1.
Self test of micro is executed If self test is OK, than all indicators
and test program begins: are switched OFF
Press and hold buttons S2 and • All indicators switch ON for 5 • LED/LCD display shows step
S4 and rotate selector knob 1 ~10” second number 1
step in CCW direction. • All segments on LEDD/LCD • If self test is not OK, than all
switches ON for 5 second indicators and segments are blinking
¼ second ON and ¼ sec. OFF )
Motor selection (table 1):
• Indicators LED15, LED16 and LED17
• First setting is 1, at next run it
are used for A1, A2 and A3 alternative
shows last selection
Press S6 button to select motor motor variants
• Alternative motor is selected
alternative and S1 button for ~5” • LEDD/LCD display shows alternative
by pressing S6 button
selection confirmation motor number on last two digit as
• Motor selection also define
‘A1’, ‘A2’ or ‘A3’
unbalance parameters
Draining:
• The drain pump is switched
ON to drain the water under
level 1 (empty drum)
• Level 1 checking after 20" • If the test is OK (empty level
and: reached in 20" or maximum 43"),
A) Continue with next step than all indicators switch ON
~43" (spinning), if the drum is empty • LEDD/LCD display shows step
B) Interrupt the draining for 3 number ‘10’
seconds and repeat 20" of • If the test is not OK, then the E7
draining error is shown
• The water level is checked all
the time, and:
A) Continue with spinning if the
empty level is detected in 20"
B) E7 Error if the level empty is
not reached in 20"
• If the test is OK (reached maximum
Final spin:
spin speed), than all indicators
• The drain pump stays ON
switches OFF
• Acceleration from 0 rpm to
• LEDD/LCD display shows ‘End’ on
maximum spin speed in ~10"
remaining time area
• Tap field is switched ON at
~60" • If the test is not OK, then the E8
700 rpm for all spin speed up to
error is shown
1600rpm
• 50" on maximum spin speed
The tolerance for reaching maximum
• switch OFF all components
spin speed is 20% or maximal 200
• wait the drum to stop
rpm
gorenjegroup 4.10.2016
SERVICE INSTRUCTIONS
Washing machines and dryers 4-027-1214
Control unit:
B - Basic
C - Classic
E1 - Exclusive 1
E2 - Exclusive 2
14 - Drum speed
8 - Load
When selecting service CU you need to take into account service index (SI), production
date and motor type.
Service CU BASIC
SELECTOR POSITION
Service
Buttons
control Code for Load Drum speed Selector Jet pump
S1, S2 in S3
unit configuration
EK B
PS-10/-A2-
353292 363495 1 2 1 1 1
08-5
EK B
PS-10/-A1-
353176 2 1 1 1 1
06-6
EK B
PS-10/-A1-
353258 2 2 1 1 1
08-6
EK B
PS-10/-A1-
387585 3 1 1 1 1
06-7
EK B
PS-10/-A2-
394199 3 1 1 1 1
06-7
EK B
PS-10/-A2-
353288 3 2 1 1 1
08-7
EK B/1
PS-10/-A2-
363498 1 3 1 1 1
10-5
EK B/1
PS-10/-A2-
385501 1 5 1 1 1
12-5
EK B/1
PS-10/-A2-
353180 2 3 1 1 1
10-6
EK B/1
PS-10/-A2-
353322 2 5 1 1 1
12-6
EK B/1
PS-10/-A3-
343060 3 3 1 1 1
10-7
EK B/1
PS-10/-A3-
353292 3 5 1 1 1
12-7-SN
EK B/1
PS-10/-A3-
445356 3 7 1 1 1
14-7
EK B
PS-10/-A2-
499129 363495 1 2 1 1 1
08-5
EK B
353176 2 1 1 1 1
PS-10/-A1-
06-6
EK B
PS-10/-A1-
353258 2 2 1 1 1
08-6
EK B
PS-10/-A1-
387585 3 1 1 1 1
06-7
EK B
PS-10/-A2-
394199 3 1 1 1 1
06-7
EK B
PS-10/-A2-
353288 3 2 1 1 1
08-7
EK B/1
PS-10/-A2-
363498 1 3 1 1 1
10-5
EK B/1
PS-10/-A2-
385501 1 5 1 1 1
12-5
EK B/1
PS-10/-A2-
353180 2 3 1 1 1
10-6
EK B/1
PS-10/-A2-
353322 2 5 1 1 1
12-6
EK B/1
PS-10/-A3-
343060 3 3 1 1 1
10-7
EK B/1
PS-10/-A3-
445356 3 7 1 1 1
14-7
499129 EK B/1 3 5 1 1 1
PS-10/-A3-
12-7
EK B/1
PS-10/-A1-
561830 1 3 1 1 1
10-5
When selecting alternative A LED15 lights up, when B LED16 lights up and when you select C
LED17 lights up.
Motor alternative is labeled on tube side (on picture) and technical info 4-027-1113.
After
Regular Drum
Supplier Type Code Sales Load Alternative
production speed
Service
Welling 6, 7 1
HXG 30 154542 YES YES 600
UM kg
A
A1
6, 7
HXG 40 154543 YES YES 800
kg
6, 7
HXG 52 307327 / / 1000-1200
kg
6, 7
HXG52A54.04 154545 YES YES 1300-1400
kg
6, 7
HXG52-AL 413600 YES YES 1000-1200
kg
1BA6745-0701
ATLANT 469169 YES / SLIM 800-1200
PL.CA
Askoll
H19-NS 03CA 513488 YES YES 7 kg 1200-1600
BPM
6, 7 2
Selni UM W35 267980 YES YES 600
kg
B
A2
6, 7
MCA52/64-148/KT14 228960 YES YES 800
kg
6, 7
MCA61/64-148/KT7 587542 / / 1000-1200
kg
6, 7
MCA61/64-148/KT16 273680 YES YES 1300-1400
kg
MCA61/64-148/KT18 6, 7
587548 YES YES 1000-1200
AL kg
MCA 61/64-
475799 YES YES SLIM 1300-1400
148/KT20 AL
6, 7
MCA61 KT22-60Hz 521191 YES YES 1300-1400
kg
6, 7
MCA61 KT21-60Hz 521211 YES YES 1000-1200
kg
6, 7
C51.05.47.07 280350 YES YES 600
kg
Ana
Imep UM 3
A3
Nidec 6, 7
T63-G01 470070 YES YES 1000-1200
UM kg
6, 7
WU112U40 497151 YES / 800
kg
WU126 T65-G02
521212 YES YES 8 kg 1300-1400
60Hz
6, 7
T63 587540 / / 1000-1200
kg
6, 7
P33 291266 / / 1300-1400
kg
Selni UM
P71 387969 / / 8 kg 1000-1200
SERVICE INSTRUCTIONS
Washing machines and dryers 4-027-1215
Control unit:
B - Basic
C - Classic
E1 - Exclusive 1
E2 - Exclusive 2
14 - Drum speed
8 - Load
When selecting service CU you need to take into account service index (SI), production
date and motor type.
Service CU CLASSIC
Service Buttons
Code for Drum Jet
control Load S1, S2 Selector
configuration speed pump
unit in S3
EK C/1 PS-10/-A3-14-5-
555060 1 7 1 1 1
EMCU
353278 EK C PS-10/-A2-08-7 3 2 1 1 1
353278 EK C PS-10/-A2-08-7 3 2 1 1 1
EK C/1-M PS-10/-A4-14-8-
497282 497282 4 7 1 1 2
AU
EK C/1-M PS-10/-A3-14-8-
475088 475088 4 7 1 2 1
VT
EK C/1 SY2 PS-10/-A3-12-
431624 431624 3 5 2 3 1
7-SM
EK C/1 BM PS-10/-A4B-14-
464814 464814 3 7 1 1 1
7
EK C/1-M BM PS-10/-A4-
477686 477686 4 9 1 1 2
16-8
EK C/1-M BM PS-10/-A3-
478244 4 7 1 1 1
14-8
EK C/1-M BM PS-10/-A4-
478424 4 5 1 1 2
12-8
EK C/1-M BM PS-10/-A4B-
496370 4 7 1 1 1
14-8
EK C/1-M BM PS-10/-A4-
500215 5 9 1 1 2
16-9
EK C/1 BM PS-10/-A4B-14-
477834 477834 4 7 1 2 1
8-VT
EK C/1 BM PS-10/-A3-12-
497229 497229 1 5 1 2 1
5-VT
EK C/1 BM PS-10/-A4B-12-
497079 497079 3 5 1 2 1
7-VT
EK C/1-M BM PS-10/-A4B-
515707 515707 3 9 1 1 1
16-7
EK C/1-M BM PS-10/-A4B-
554622 554622 4 9 1 1 1
16-8
EK C/1-M BM PS-10/-A4B-
477874 477874 4 7 1 2 1
14-8-VT
EK C/1-M BM PS-10/-A4-
532290 4 9 1 2 2
16-8-VT
Welling UM
MCA61/64-148/KT19 387970 YES YES 8 kg 1000-1200
MCA61/64-148/KT18
587548 YES YES 6, 7 kg 1000-1200
AL
MCA 61/64-148/KT20
475799 YES YES SLIM 1300-1400
AL
Ana Imep UM
WU126 T65- G00 345880 YES YES 7 kg 1500-1600