Documente Academic
Documente Profesional
Documente Cultură
EN
6
10
9
15 1
11
8 21
Torque screws to
16 14 72 inch pounds.
8
12
16
2
19 See insets
at left for
8 detailed view.
19
16
15
3
4 5 18 20
17 13 7
PARTS LIST
When ordering, please specify Part No.
ITEM PART 10 84-351 HANDLE...................................... 1
NO. NO. DESCRIPTION 11 84-359 BONNET...................................... 1
QTY. 12 84-362 RETAINER................................... 1
1 20-262 NUT, 1/2-13................................... 1 13 84-363 ■ VALVE (84-404, 84-504)..................... 1
2 20-783 SCREW, 1/4-20............................... 6 14 84-365 SPRING ...................................... 1
3 20-4401 PLUG, 1/4 NPT............................... 1 15 84-388▲ GASKET, VELLUMOID....................... 1
4 20-2848 ELBOW, 1/4 NPT............................. 1 16 84-399▲ DIAPHRAGM, PTFE........................ 2
5 20-5632 NIPPLE, 1/4 NPT............................ 1 17 84-454 ■ SEAT (84-404, 84-504)...................... 1
6 83-2744* GAUGE, 200 PSI............................. 1 18 84-455 BODY, 3/4 NPT(f) (84-404)................. 1
7 84-328 DISC .......................................... 2 19 84-463▲ GASKET, VELLUMOID....................... 1
8 84-330▲ DIAPHRAGM, NYLON...................... 2 20 84-489 BODY, 1-1/4 NPT(f) (84-504)............... 1
9 84-348* CONNECTOR................................ 1 21 85-10 BUTTON...................................... 1
* Optional, not furnished. Please order separately. NOTE: The following items are obsolete
▲ Also available in Soft Seal Repair Kit 6-1310. (refer to Part Sheet 1889R-7):
Kit not included, please order separately. 84-530 BACK PRESSURE VALVE
■ Also available in Valve Repair Kit 6-1312. 84-544 BACK PRESSURE VALVE
Kit not included, please order separately.
! WARNING
Read the following warnings before using this equipment.
READ THE MANUAL PROJECTILE HAZARD
Before operating finishing equipment, read and understand all You may be injured by venting liquids or gases that are released
safety, operation and maintenance information provided in the under pressure, or flying debris.
operation manual.
IT IS THE RESPONSIBILITY OF THE EMPLOYER TO PROVIDE THIS INFORMATION TO THE OPERATOR OF THE EQUIPMENT.
FOR FURTHER SAFETY INFORMATION REGARDING THIS EQUIPMENT, SEE THE GENERAL EQUIPMENT SAFETY BOOKLET (77-5300).
INSTRUCTIONS
INSTALLATION: MAINTENANCE:
1. W hen installing back pressure valve assembly, 1. B ack pressure valve can be serviced without
make certain that ARROW underneath valve removing the valve from the line.
body points toward DOWNSTREAM side of 2. To replace diaphragms, gaskets or seats:
system. a. Turn handle (10) in a counter-clockwise
2. Make certain that inlet and outlet connections are direction until tension from spring (14) is
tight. relieved.
3. If valve is installed in other than the upright b. Remove screws (2).
(vertical) position, make certain that the gauge c. Remove valve (13).
assembly (6) is in the upright position in all
3. T o reassemble, reverse procedure as outlined.
cases. The gauge assembly may be installed in
When reassembling, note sequence of
either of the 1/4 NPT outlets.
diaphragms and gaskets. The gasket (15)
fits between the diaphragms (8) and (16).
OPERATION: The diaphragms are located below the other
1. W
ith system in operation, turn handle (10) in a gasket (19). See detailed insets on diagram on
clockwise direction until desired back pressure or page 1.
flow rate is obtained. To reduce back pressure,
reverse procedure.
2. Tighten nut (1) to maintain desired back
pressure.
NOTE
HIGHER back pressure REDUCES flow rate.
LOWER back pressure INCREASES flow rate.
This product is covered by Carlisle Fluid Technologies’ materials and workmanship limited warranty.
The use of any parts or accessories, from a source other than Carlisle Fluid Technologies,
will void all warranties. Failure to reasonably follow any maintenance guidance provided
may invalidate any warranty.