Documente Academic
Documente Profesional
Documente Cultură
MY TEST
MY PROFILE
REPORTS
Ask an Expert
Q. Question Status
No
Q.1
a. 60 rad/s
b. 120 rad/s
c. 80 rad/s
d. 30 rad/s
Q.2
1 of 14 02/17/2017 01:21 AM
MADE EASY ONLINE TEST SERIES https://onlinetestseriesmadeeasy.in/madeeasy/ind...
a. Both correct
b. I correct
c. II correct
d. None correct
Q.3
Which one of the flowing is the correct formula for the height of Porter
governor, if force of friction(f) at sleeve is zero and m = mass of each
ball; M = Mass of the sleeve; f = force of friction at the sleeve ; h =
height of governor and k = ratio of tangent of angle of upper and lower
arm with the vertical
a.
b.
c.
d.
Q.4
2 of 14 02/17/2017 01:21 AM
MADE EASY ONLINE TEST SERIES https://onlinetestseriesmadeeasy.in/madeeasy/ind...
a. Both I and II
b. None of the two
c. II only
d. I only
Q.5
a. θ = 45° or 225°
b. θ = 90° or 270°
c. θ = 180° or 360°
d. θ = 180° or 315°
Q.6
a. pitch circle
b. prime circle
c. base circle
d. pitch curve
Q.7
3 of 14 02/17/2017 01:21 AM
MADE EASY ONLINE TEST SERIES https://onlinetestseriesmadeeasy.in/madeeasy/ind...
a. 503 N.s/m
b. 725 N.s/m
c. 1001 N.s/m
d. 1500 N.s/m
Q.8
a. 3.185
b. 3
c. 3.955
d. 6
Q.9
4 of 14 02/17/2017 01:21 AM
MADE EASY ONLINE TEST SERIES https://onlinetestseriesmadeeasy.in/madeeasy/ind...
Q.10
Q.11
Q.12
A cam operates a knife edge follower having a lift of 30 mm. The cam
raises the follower with SHM for 180° of rotation followed by a period of
dwell for 60°. The follower descends for next 100° rotation of cam with
uniform velocity, again followed by a dwell period.
The cam rotates at 120 rpm and has a least radius of 20 mm. The
maximum acceleration of follower during lift will be __________ m/s 2.
5 of 14 02/17/2017 01:21 AM
MADE EASY ONLINE TEST SERIES https://onlinetestseriesmadeeasy.in/madeeasy/ind...
Q.13
Q.14
In the figure shown below, the relative velocity of link 1 with respect to
link 2 is 16 m/s. Link 2 rotates at a constant speed of 90 rpm. The
magnitude of Coriolis component of acceleration of link 1 is
_________m/s2.
Q.15
6 of 14 02/17/2017 01:21 AM
MADE EASY ONLINE TEST SERIES https://onlinetestseriesmadeeasy.in/madeeasy/ind...
Q.16
Q.17
a. 1872
b. 11609
c. 9959
d. 8569
Q.18
One of the driving axles of a locomotive with its two wheels has
moment of inertia of 350 kg-m2. The wheels are of 1.85 m diameter. The
distance between the planes of the wheels is 1.5 m. When travelling at
100 km/hr the locomotive passes over a defective rail which causes the
right hand wheel to fall 12 mm and rise again in total time of 0.1 sec, the
vertical movement of wheel being S.H.M. What is the maximum
gyroscopic torque when the wheel is falling?
a. 1320.75 Nm
b. 3641.5 Nm
c. 2641.5 Nm
d. 5251.2 Nm
7 of 14 02/17/2017 01:21 AM
MADE EASY ONLINE TEST SERIES https://onlinetestseriesmadeeasy.in/madeeasy/ind...
Q.19
For the system shown in figure, the undamped natural frequency of the
system in rad/s is
a.
b.
c.
d.
Q.20
8 of 14 02/17/2017 01:21 AM
MADE EASY ONLINE TEST SERIES https://onlinetestseriesmadeeasy.in/madeeasy/ind...
d. None of these
Q.21
Q.22
a. 10 Hz
9 of 14 02/17/2017 01:21 AM
MADE EASY ONLINE TEST SERIES https://onlinetestseriesmadeeasy.in/madeeasy/ind...
b. 5 Hz
c. 1.5 Hz
d. 20 Hz
Q.23
a. 17, 51
b. 18, 54
c. 19, 57
d. 20, 60
Q.24
a. 1, 2 and 3 only
b. 1, 3 and 4 only
c. 2, 3 and 4 only
d. 1, 2, 3 and 4
Q.25
10 of 14 02/17/2017 01:21 AM
MADE EASY ONLINE TEST SERIES https://onlinetestseriesmadeeasy.in/madeeasy/ind...
Match List-I (Type of Gears) with List-II (Characteristics) and select the
correct answer using the code given below the lists:
List-I List-II
A Helical gearing 1 Zero axial thrust
B Herringbone gearing 2 Non-inter-changeable
C Worm gearing 3 Skew shafts
D Hypoid gearing 4 Parallel shafts
a. a
b. b
c. c
d. d
Q.26
11 of 14 02/17/2017 01:21 AM
MADE EASY ONLINE TEST SERIES https://onlinetestseriesmadeeasy.in/madeeasy/ind...
Q.27
Q.28
Q.29
12 of 14 02/17/2017 01:21 AM
MADE EASY ONLINE TEST SERIES https://onlinetestseriesmadeeasy.in/madeeasy/ind...
Q.30
Q.31
Q.32
13 of 14 02/17/2017 01:21 AM
MADE EASY ONLINE TEST SERIES https://onlinetestseriesmadeeasy.in/madeeasy/ind...
Q.33
14 of 14 02/17/2017 01:21 AM