Documente Academic
Documente Profesional
Documente Cultură
1-1/8-228:2002
An American National Standard
--`,``,,,,,,```,`,`,,,```,,,,``-`-`,,`,,`,`,,`---
(M-1/P-1/S-1, Groups 1
or 2) to Austenitic
Stainless Steel (M-8/
P-8/S-8, Group 1), 1/8
through 1-1/2 inch Thick,
E309(L)-15, -16, or -17,
As-Welded Condition,
Primarily Pipe Applications
Site License
Prepared by
AWS B2 Committee on Welding Qualification
Approved by
AWS Board of Directors
Abstract
This standard contains the essential welding variables for welding carbon steel to austenitic stainless steel in the thick-
ness range of 1/8 through 1-1/2 inch, using manual shielded metal arc welding. It cites the base metals and operating
conditions necessary to make the weldment, the filler metal specifications, and the allowable joint designs for groove
and fillet welds. This SWPS was developed primarily for pipe applications.
--`,``,,,,,,```,`,`,,,```,,,,``-`-`,,`,,`,`,,`---
550 N.W. LeJeune Road, Miami, Florida 33126
--`,``,,,,,,```,`,`,,,```,,,,``-`-`,,`,,`,`,,`---
regulations. In all cases, these standards carry the full legal authority of the contract or other document that invokes the
AWS standards. Where this contractual relationship exists, changes in or deviations from requirements of an AWS
standard must be by agreement between the contracting parties.
International Standard Book Number: 0-87171-707-7
American Welding Society, 550 N.W. LeJeune Road, Miami, FL 33126
© 2002 by American Welding Society. All rights reserved
Printed in the United States of America
AWS American National Standards are developed through a consensus standards development process that brings
together volunteers representing varied viewpoints and interests to achieve consensus. While AWS administers the process
and establishes rules to promote fairness in the development of consensus, it does not independently test, evaluate, or
verify the accuracy of any information or the soundness of any judgments contained in its standards.
AWS disclaims liability for any injury to persons or to property, or other damages of any nature whatsoever, whether spe-
cial, indirect, consequential or compensatory, directly or indirectly resulting from the publication, use of, or reliance on this
standard. AWS also makes no guaranty or warranty as to the accuracy or completeness of any information published herein.
In issuing and making this standard available, AWS is not undertaking to render professional or other services for or on
behalf of any person or entity. Nor is AWS undertaking to perform any duty owed by any person or entity to someone
else. Anyone using these documents should rely on his or her own independent judgment or, as appropriate, seek the advice
of a competent professional in determining the exercise of reasonable care in any given circumstances.
This standard may be superseded by the issuance of new editions. Users should ensure that they have the latest edition.
Publication of this standard does not authorize infringement of any patent. AWS disclaims liability for the infringement
of any patent resulting from the use or reliance on this standard.
Finally, AWS does not monitor, police, or enforce compliance with this standard, nor does it have the power to do so.
On occasion, text, tables, or figures are printed incorrectly (errata). Such errata, when discovered, are shown on the
American Welding Society web page (www.aws.org) under “Technical” in the Departments column.
Official interpretations of any of the technical requirements of this standard may be obtained by sending a request, in writing,
to the Managing Director, Technical Services Division, American Welding Society, 550 N.W. LeJeune Road, Miami, FL
33126 (see Annex A). With regard to technical inquiries made concerning AWS standards, oral opinions on AWS standards
may be rendered. However, such opinions represent only the personal opinions of the particular individuals giving them.
These individuals do not speak on behalf of AWS, nor do these oral opinions constitute official or unofficial opinions or inter-
pretations of AWS. In addition, oral opinions are informal and should not be used as a substitute for an official interpretation.
This standard is subject to revision at any time by the AWS B2 Committee on Welding Qualification. It must be reviewed
every five years, and if not revised, it must be either reapproved or withdrawn. Comments (recommendations, additions,
or deletions) and any pertinent data that may be of use in improving this standard are required and should be addressed to
AWS Headquarters. Such comments will receive careful consideration by the AWS B2 Committee on Welding Qualifi-
cation and the author of the comments will be informed of the Committee’s response to the comments. Guests are invited
to attend all meetings of the AWS B2 Committee on Welding Qualification to express their comments verbally. Proce-
dures for appeal of an adverse decision concerning all such comments are provided in the Rules of Operation of the
Technical Activities Committee. A copy of these Rules can be obtained from the American Welding Society, 550 N.W.
LeJeune Road, Miami, FL 33126.
iii
Copyright American Welding Society
Provided by IHS under license with AWS Licensee=ExxonMobil/1890500101
No reproduction or networking permitted without license from IHS Not for Resale, 02/03/2007 11:45:04 MST
Foreword
(This Foreword is not a part of AWS B2.1-1/8-228:2002, Standard Welding Procedure Specification (SWPS) for
Shielded Metal Arc Welding of Carbon Steel (M-1/P-1/S-1, Groups 1 or 2) to Austenitic Stainless Steel
(M-8/P-8/S-8, Group 1), 1/8 through 1-1/2 inch Thick, E309(L)-15, -16, or -17, As-Welded Condition,
Primarily Pipe Applications, but is included for informational purposes only.)
The American Welding Society and the Welding Research Council have joined in a cooperative effort to generate
standard welding procedures for industry. The need for pretested welding procedures that are supported by adequate test
data and that satisfy the technical requirements for the commonly used construction codes and specifications has been
expressed by many individuals and organizations. The purpose of a welding procedure qualification is to provide test
data for assessing the properties of a weld joint.
This Standard Welding Procedure Specification is an outgrowth of the coordinated work of the Welding Procedures
Committee of WRC and the Committee on Welding Qualification of the AWS. The Welding Procedures Committee has
provided the test data documented on the Summary of Procedure Qualification Records, which are available from the
Welding Research Council.
The welding terms used in this specification shall be interpreted in accordance with the definitions given in the latest
edition of AWS A3.0, Standard Welding Terms and Definitions. Welding symbols shall be those shown in the latest edition
of AWS A2.4, Standard Symbols for Welding, Brazing, and Nondestructive Examination.
The AWS B2 Committee on Welding Qualification was formed in 1979 to provide welding standards concerning the
subject of qualification. The primary document developed by this committee, AWS B2.1, Specification for Welding Pro-
cedure and Performance Qualification, was published in 1984. AWS B2.1 was revised in 1998 and 2000. AWS B2.1 es-
tablished the foundation and framework for Standard Welding Procedure Specifications (SWPSs). The first SWPSs were
published in 1990. AWS continues to publish SWPSs.
Comments and suggestions for the improvement of this standard are welcomed. They should be sent to the Secretary,
AWS B2 Committee on Welding Qualification, American Welding Society, 550 N.W. LeJeune Road, Miami, FL 33126.
--`,``,,,,,,```,`,`,,,```,,,,``-`-`,,`,,`,`,,`---
iv
Copyright American Welding Society
Provided by IHS under license with AWS Licensee=ExxonMobil/1890500101
No reproduction or networking permitted without license from IHS Not for Resale, 02/03/2007 11:45:04 MST
AWS B2.1-1/8-228:2002
Page 1 of 12
Permission to reproduce for intra-company use only is granted by the American Welding Society
--`,``,,,,,,```,`,`,,,```,,,,``-`-`,,`,,`,`,,`---
LIMITATIONS
WELDING PROCESSES
BASE METALS
Base Metal:2 Carbon Steel to Stainless Steel, M-1, P-1, or S-1, Group 1 or 2, to
M-8, P-8, or S-8, Group 1
Thickness Range: 1/8 in. through 1-1/2 in. for groove welds,
1/8 in. minimum for fillet welds
Pipe Diameter: Groove Welds: 3/4 NPS minimum,
Fillet Welds: 1/2 NPS minimum.
FILLER METALS
JOINT DESIGNS
POSITIONS
2. M, P, and S numbers for base metal and F and A numbers for filler metal and weld metal, respectively, are as detailed in
AWS B2.1 and ASME Boiler and Pressure Vessel Code, Section IX.
--`,``,,,,,,```,`,`,,,```,,,,``-`-`,,`,,`,`,,`---
Permission to reproduce for intra-company use only is granted by the American Welding Society
Copyright American Welding Society
Provided by IHS under license with AWS Licensee=ExxonMobil/1890500101
No reproduction or networking permitted without license from IHS Not for Resale, 02/03/2007 11:45:04 MST
AWS B2.1-1/8-228:2002
Page 3 of 12
ELECTRICAL CHARACTERISTICS
TECHNIQUE
In the name of the Company stated above, I accept full responsibility for the application of this SWPS for use
with:
Permission to reproduce for intra-company use only is granted by the American Welding Society
Copyright American Welding Society
Provided by IHS under license with AWS Licensee=ExxonMobil/1890500101
No reproduction or networking permitted without license from IHS Not for Resale, 02/03/2007 11:45:04 MST
AWS B2.1-1/8-228:2002
Page 4 of 12
Metric Conversions
in. mm °F °C NPS DN
--`,``,,,,,,```,`,`,,,```,,,,``-`-`,,`,,`,`,,`---
1/16 1.6 350 175 3/4 25
3/32 2.4
1/8 3.2
5/32 4.0
3/16 4.8
1/4 6.4
3/4 19.0
1 25.4
1-1/2 38.0
Permission to reproduce for intra-company use only is granted by the American Welding Society
Copyright American Welding Society
Provided by IHS under license with AWS Licensee=ExxonMobil/1890500101
No reproduction or networking permitted without license from IHS Not for Resale, 02/03/2007 11:45:04 MST
AWS B2.1-1/8-228:2002
Page 5 of 12
JOINT 1
RECOMMENDED WELDING DIMENSIONS FOR SOCKET WELDING COMPONENTS OTHER THAN FLANGES
JOINT 2
Permission to reproduce for intra-company use only is granted by the American Welding Society
Copyright American Welding Society
Provided by IHS under license with AWS Licensee=ExxonMobil/1890500101
No reproduction or networking permitted without license from IHS Not for Resale, 02/03/2007 11:45:04 MST
AWS B2.1-1/8-228:2002
Page 6 of 12
X MIN. = 1/4 Tn OR THE THICKNESS OF THE HUB, WHICHEVER IS SMALLER, UNLESS OTHERWISE REQUIRED BY THE
FABRICATION DOCUMENT(S)
Y MIN. = Tn OR 1/4 in., WHICHEVER IS SMALLER, UNLESS OTHERWISE REQUIRED BY THE FABRICATION DOCUMENT(S)
Tn = NOMINAL PIPE WALL THICKNESS
JOINT 3
Permission to reproduce for intra-company use only is granted by the American Welding Society
Copyright American Welding Society
Provided by IHS under license with AWS Licensee=ExxonMobil/1890500101
No reproduction or networking permitted without license from IHS Not for Resale, 02/03/2007 11:45:04 MST
AWS B2.1-1/8-228:2002
Page 7 of 12
Nonmandatory Annex
Annex A
Guidelines for Preparation of Technical Inquiries
for AWS Technical Committees
(This Annex is not a part of AWS B2.1-1/8-228:2002, Standard Welding Procedure Specification (SWPS) for
Shielded Metal Arc Welding of Carbon Steel (M-1/P-1/S-1, Groups 1 or 2) to Austenitic Stainless Steel
(M-8/P-8/S-8, Group 1), 1/8 through 1-1/2 inch Thick, E309(L)-15, -16, or -17, As-Welded Condition,
Primarily Pipe Applications, but is included for informational purposes only.)
--`,``,,,,,,```,`,`,,,```,,,,``-`-`,,`,,`,`,,`---
nical justification for that revision.
All inquiries must be directed to: A2.4 Proposed Reply. The inquirer should, as a pro-
posed reply, state an interpretation of the provision that is
Managing Director, Technical Services
the point of the inquiry, or the wording for a proposed
American Welding Society
revision, if that is what inquirer seeks.
550 N.W. LeJeune Road
Miami, FL 33126
All inquiries must contain the name, address, and af- A3. Interpretation of Provisions of the
filiation of the inquirer, and they must provide enough in- Standard
formation for the committee to fully understand the point
of concern in the inquiry. Where that point is not clearly Interpretations of provisions of the standard are made
defined, the inquiry will be returned for clarification. For by the relevant AWS Technical Committee. The secretary
efficient handling, all inquiries should be typewritten and of the committee refers all inquiries to the chairman of
should also be in the format used here. the particular subcommittee that has jurisdiction over the
portion of the standard addressed by the inquiry. The
A2.1 Scope. Each inquiry must address one single pro- subcommittee reviews the inquiry and the proposed reply
vision of the standard, unless the point of the inquiry to determine what the response to the inquiry should be.
Permission to reproduce for intra-company use only is granted by the American Welding Society
Copyright American Welding Society
Provided by IHS under license with AWS Licensee=ExxonMobil/1890500101
No reproduction or networking permitted without license from IHS Not for Resale, 02/03/2007 11:45:04 MST
AWS B2.1-1/8-228:2002
Page 8 of 12
Following the subcommittee’s development of the re- an official interpretation of any AWS standard with the
sponse, the inquiry and the response are presented to the information that such an interpretation can be obtained
entire committee for review and approval. Upon approval only through a written request. The Headquarters staff
by the committee, the interpretation will be an official in- cannot provide consulting services. The staff can, how-
terpretation of the Society, and the secretary will transmit ever, refer a caller to any of those consultants whose
the response to the inquirer and to the Welding Journal names are on file at AWS Headquarters.
for publication.
--`,``,,,,,,```,`,`,,,```,,,,``-`-`,,`,,`,`,,`---
Permission to reproduce for intra-company use only is granted by the American Welding Society
Copyright American Welding Society
Provided by IHS under license with AWS Licensee=ExxonMobil/1890500101
No reproduction or networking permitted without license from IHS Not for Resale, 02/03/2007 11:45:04 MST
AWS B2.1-1/8-228:2002
Page 9 of 12
Backing
B2.1-1-016-94 Standard Welding Procedure Specification (WPS) for Shielded Metal Arc Welding of Carbon
Steel (M-1/P-1/S-1, Group 1 or 2), 1/8 through 1-1/2 inch Thick, E7018, As-Welded or PWHT
Condition
Permission to reproduce for intra-company use only is granted by the American Welding Society
Copyright American Welding Society
Provided by IHS under license with AWS Licensee=ExxonMobil/1890500101
No reproduction or networking permitted without license from IHS Not for Resale, 02/03/2007 11:45:04 MST
AWS B2.1-1/8-228:2002
Page 10 of 12
Designation Title
B2.1-1-017-94 Standard Welding Procedure Specification (WPS) for Shielded Metal Arc Welding of Carbon
Steel (M-1/P-1/S, Group 1 or 2), 1/8 through 1-1/2 inch Thick, E6010, As-Welded or PWHT
Condition
B2.1-1-018-94 Standard Welding Procedure Specification (WPS) for Self-Shielded Flux Cored Arc Welding
of Carbon Steel (M-1/P-1/S-1, Group 1 or 2), 1/8 through 1-1/2 inch Thick, E71T-8, As-Welded
Condition
B2.1-1-019-94 Standard Welding Procedure Specification (WPS) for CO2 Shielded Flux Cored Arc Welding
of Carbon Steel (M-1/P-1/S-1, Group 1 or 2), 1/8 through 1-1/2 inch Thick, E70T-1 and
E71T-1, As-Welded Condition
B2.1-1-020-94 Standard Welding Procedure Specification (WPS) for 75% Ar/25% CO2 Shielded Flux Cored
--`,``,,,,,,```,`,`,,,```,,,,``-`-`,,`,,`,`,,`---
Arc Welding of Carbon Steel (M-1/P-1/S-1, Group 1 or 2), 1/8 through 1-1/2 inch Thick,
E70T-1 and E71T-1, As-Welded or PWHT Condition
B2.1-1-021-94 Standard Welding Procedure Specification (WPS) for Gas Tungsten Arc Welding Followed
by Shielded Metal Arc Welding of Carbon Steel (M-1/P-1/S-1, Group 1 or 2), 1/8 through
1-1/2 inch Thick, ER70S-2 and E7018, As-Welded or PWHT Condition
B2.1-1-022-94 Standard Welding Procedure Specification (WPS) for Shielded Metal Arc Welding of Carbon
Steel (M-1/P-1/S-1, Group 1 or 2), 1/8 through 1-1/2 inch Thick, E6010 (Vertical Uphill)
Followed by E7018, As-Welded or PWHT Condition
B2.1-8-023-94 Standard Welding Procedure Specification (WPS) for Shielded Metal Arc Welding of
Austenitic Stainless Steel (M-8/P-8/S-8, Group 1), 1/8 through 1-1/2 inch Thick, As-Welded
Condition
B2.1-8-024:2001 Standard Welding Procedure Specification (WPS) for Gas Tungsten Arc Welding of Austenitic
Stainless Steel (M-8/P-8/S-8, Group 1), 1/16 through 1-1/2 inch Thick, ER3XX, As-Welded
Condition, Primarily Plate and Structural Applications
B2.1-8-025:2001 Standard Welding Procedure Specification (WPS) for Gas Tungsten Arc Welding followed
by Shielded Metal Arc Welding of Austenitic Stainless Steel (M-8/P-8/S-8, Group 1), 1/8
through 1-1/2 inch Thick, ER3XX and E3XX-XX, As-Welded Condition, Primarily Plate and
Structural Applications
B2.1-1-026-94 Standard Welding Procedure Specification (WPS) for Shielded Metal Arc Welding of Carbon
Steel (M-1/P-1/S-1, Group 1 or 2). 1/8 through 1-1/2 inch Thick, E6010 (Vertical Downhill)
Followed by E7018, As-Welded or PWHT Condition
B2.1-1-027:1998 Standard Welding Procedure Specification (WPS) for Self-Shielded Flux Cored Arc Welding
of Carbon Steel (M-1/P-1/S-1, Group 1 or 2), 1/8 through 1/2 inch Thick, E71T-11, As-Welded
Condition
B2.1-1-201-96 Standard Welding Procedure Specification (WPS) for Shielded Metal Arc Welding of Carbon
Steel (M-1/P-1/S-1, Group 1 or 2), 1/8 through 3/4 inch Thick, E6010 (Vertical Uphill)
Followed by E7018 (Vertical Uphill), As-Welded Condition, Primarily Pipe Applications
B2.1-1-202-96 Standard Welding Procedure Specification (WPS) for Shielded Metal Arc Welding of Carbon
Steel (M-1/P-1/S-1, Group 1 or 2), 1/8 through 3/4 inch Thick, E6010 (Vertical Downhill)
Followed by E7018 (Vertical Uphill), As-Welded Condition, Primarily Pipe Applications
B2.1-1-203-96 Standard Welding Procedure Specification (WPS) for Shielded Metal Arc Welding of Carbon
Steel (M-1/P-1/S-1, Group 1 or 2), 1/8 through 3/4 inch Thick, E6010 (Vertical Uphill), As-
Welded Condition, Primarily Pipe Applications
B2.1-1-204-96 Standard Welding Procedure Specification (WPS) for Shielded Metal Arc Welding of Carbon
Steel (M-1/P-1/S-1, Group 1 or 2), 1/8 through 3/4 inch Thick, E6010 (Vertical Downhill Root
with the Balance Vertical Uphill), As-Welded Condition, Primarily Pipe Applications
B2.1-1-205-96 Standard Welding Procedure Specification (WPS) for Shielded Metal Arc Welding of Carbon Steel
(M-1/P-1/S-1, Group 1 or 2), 1/8 through 1-1/2 inch Thick, E6010 (Vertical Uphill) Followed
by E7018 (Vertical Uphill), As-Welded or PWHT Condition, Primarily Pipe Applications
Permission to reproduce for intra-company use only is granted by the American Welding Society
Copyright American Welding Society
Provided by IHS under license with AWS Licensee=ExxonMobil/1890500101
No reproduction or networking permitted without license from IHS Not for Resale, 02/03/2007 11:45:04 MST
AWS B2.1-1/8-228:2002
Page 11 of 12
Designation Title
B2.1-1-206-96 Standard Welding Procedure Specification (WPS) for Shielded Metal Arc Welding of
Carbon Steel (M-1/P-1/S-1, Group 1 or 2), 1/8 through 1-1/2 inch Thick, E6010 (Vertical
Downhill) Followed by E7018 (Vertical Uphill), As-Welded or PWHT Condition, Primarily
Pipe Applications
B2.1-1-207-96 Standard Welding Procedure Specification (WPS) for Gas Tungsten Arc Welding of Carbon
Steel (M-1/P-1/S-1, Group 1 or 2), 1/8 through 1-1/2 inch Thick, ER70S-2, As-Welded or
PWHT Condition, Primarily Pipe Applications
B2.1-1-208-96 Standard Welding Procedure Specification (WPS) for Shielded Metal Arc Welding of Carbon
Steel (M-1/P-1/S-1, Group 1 or 2), 1/8 through 1-1/2 inch Thick, E7018, As-Welded or PWHT
Condition, Primarily Pipe Applications
B2.1-1-209-96 Standard Welding Procedure Specification (WPS) for Gas Tungsten Arc Welding Followed
by Shielded Metal Arc Welding of Carbon Steel (M-1/P-1/S-1, Group 1 or 2), 1/8 through
1-1/2 inch Thick, ER70S-2 and E7018, As-Welded or PWHT Condition, Primarily Pipe
Applications
B2.1-1-210:2001 Standard Welding Procedure Specification (WPS) for Gas Tungsten Arc Welding with Con-
sumable Insert Root of Carbon Steel (M-1/P-1/S-1, Group 1 or 2), 1/8 through 1-1/2 inch
Thick, INMs-1 and ER70S-2, As-Welded or PWHT Condition, Primarily Pipe Applications
B2.1-1-211:2001 Standard Welding Procedure Specification (WPS) for Gas Tungsten Arc Welding with
Consumable Insert Root followed by Shielded Metal Arc Welding of Carbon Steel (M-1/P-1/
S-1, Group 1 or 2), 1/8 through 1-1/2 inch Thick, INMs-1, ER70S-2, and E7018, As-Welded
Condition, Primarily Pipe Applications
B2.1-8-212:2001 Standard Welding Procedure Specification (WPS) for Gas Tungsten Arc Welding of Austenitic
Stainless Steel (M-8/P-8/S-8, Group 1), 1/16 through 1-1/2 inch Thick, ER3XX, As-Welded
Condition, Primarily Pipe Applications
B2.1-8-213-97 Standard Welding Procedure Specification (WPS) for Shielded Metal Arc Welding of Austenitic
Stainless Steel (M-8/P-8/S-8, Group 1), 1/8 through 1-1/2 inch Thick, E3XX-XX, As-Welded
Condition, Primarily Pipe Applications
B2.1-8-214:2001 Standard Welding Procedure Specification (WPS) for Gas Tungsten Arc Welding followed by
Shielded Metal Arc Welding of Austenitic Stainless Steel (M-8/P-8/S-8, Group 1), 1/8 through
--`,``,,,,,,```,`,`,,,```,,,,``-`-`,,`,,`,`,,`---
1-1/2 inch Thick, ER3XX and E3XX-XX, As-Welded Condition, Primarily Pipe Applications
B2.1-8-215:2001 Standard Welding Procedure Specification (WPS) for Gas Tungsten Arc Welding with
Consumable Insert Root of Austenitic Stainless Steel (M-8/P-8/S-8, Group 1), 1/8 through
1-1/2 inch Thick, IN3XX and ER3XX, As-Welded Condition, Primarily Pipe Applications
B2.1-8-216:2001 Standard Welding Procedure Specification (WPS) for Gas Tungsten Arc Welding with
Consumable Insert Root followed by Shielded Metal Arc Welding of Austenitic Stainless Steel
(M-8/P-8/S-8, Group 1), 1/8 through 1-1/2 inch Thick, IN3XX, ER3XX, and E3XX-XX, As-
Welded Condition, Primarily Pipe Applications
B2.1-4-217:1999 Standard Welding Procedure Specification (WPS) for Gas Tungsten Arc Welding of
Chromium-Molybdenum Steel (M-4/P-4, Group 1 or 2), ER80S-B2, 1/8 through 1/2 in.
Thick, As-Welded Condition, 1/8 through 3/4 in. Thick, PWHT Condition, Primarily Pipe
Applications
B2.1-4-218:1999 Standard Welding Procedure Specification (WPS) for Shielded Metal Arc Welding of
Chromium-Molybdenum Steel (M-4/P-4, Group 1 or 2), E8018-B2, 1/8 through 1/2 in.
Thick, As-Welded Condition, 1/8 through 1-1/2 in. Thick, PWHT Condition, Primarily Pipe
Applications
B2.1-4-219:1999 Standard Welding Procedure Specification (WPS) for Gas Tungsten Arc Welding followed by
Shielded Metal Arc Welding of Chromium-Molybdenum Steel (M-4/P-4, Group 1 or 2), 1/8
through 1/2 in. Thick, As-Welded Condition, 1/8 through 1-1/2 in. Thick, PWHT Condition,
ER80S-B2 and E8018-B2, Primarily Pipe Applications
Permission to reproduce for intra-company use only is granted by the American Welding Society
Copyright American Welding Society
Provided by IHS under license with AWS Licensee=ExxonMobil/1890500101
No reproduction or networking permitted without license from IHS Not for Resale, 02/03/2007 11:45:04 MST
AWS B2.1-1/8-228:2002
Page 12 of 12
Designation Title
B2.1-4-220:1999 Standard Welding Procedure Specification (WPS) for Gas Tungsten Arc Welding (Consum-
able Insert Root) of Chromium-Molybdenum Steel (M-4/P-4, Group 1 or 2), E8018-B2, 1/8
through 1/2 in. Thick, As-Welded Condition, 1/8 through 3/4 in. Thick, PWHT Condition,
IN515 and ER80S-B2, Primarily Pipe Applications
B2.1-4-221:1999 Standard Welding Procedure Specification (WPS) for Gas Tungsten Arc Welding (Consum-
able Insert Root) followed by Shielded Metal Arc Welding of Chromium-Molybdenum Steel
(M-4/P-4, Group 1 or 2), 1/8 through 1/2 in. Thick, As-Welded Condition, 1/8 through 1-1/2 in.
Thick, PWHT Condition, IN515, ER80S-B2, and E8018-B2, Primarily Pipe Applications
B2.1-5A-222:1999 Standard Welding Procedure Specification (WPS) for Gas Tungsten Arc Welding of
Chromium-Molybdenum Steel (M-5A/P-5A), ER90S-B3, 1/8 through 1/2 in. Thick, As-Welded
Condition, 1/8 through 3/4 in. Thick, PWHT Condition, Primarily Pipe Applications
B2.1-5A-223:1999 Standard Welding Procedure Specification (WPS) for Shielded Metal Arc Welding of
Chromium-Molybdenum Steel (M-5A/P-5A), E9018-B3, 1/8 through 1/2 in. Thick, As-Welded
Condition, 1/8 through 1-1/2 in. Thick, PWHT Condition, Primarily Pipe Applications
B2.1-5A-224:1999 Standard Welding Procedure Specification (WPS) for Gas Tungsten Arc Welding followed by
Shielded Metal Arc Welding of Chromium-Molybdenum Steel (M-5A/P-5A), 1/8 through 1/2 in.
Thick, As-Welded Condition, 1/8 through 1-1/2 in. Thick, PWHT Condition, ER90S-B3 and
E9018-B3, Primarily Pipe Applications
B2.1-5A-225:1999 Standard Welding Procedure Specification (WPS) for Gas Tungsten Arc Welding (Consum-
--`,``,,,,,,```,`,`,,,```,,,,``-`-`,,`,,`,`,,`---
able Insert Root) of Chromium-Molybdenum Steel (M-5A/P-5A), 1/8 through 1/2 in. Thick,
As-Welded Condition, 1/8 through 3/4 in. Thick, PWHT Condition, IN521 and ER90S-B3,
Primarily Pipe Applications
B2.1-5A-226:1999 Standard Welding Procedure Specification (WPS) for Gas Tungsten Arc Welding (Consum-
able Insert Root) followed by Shielded Metal Arc Welding of Chromium-Molybdenum Steel
(M-5A/P-5A), 1/8 through 1/2 in. Thick, As-Welded Condition, 1/8 through 1-1/2 in. Thick,
PWHT Condition, IN521, ER90S-B3, and E9018-B3, Primarily Pipe Applications
B2.1-1/8-227:2002 Standard Welding Procedure Specification (SWPS) for Gas Tungsten Arc Welding of Carbon
Steel (M-1/P-1/S-1, Groups 1 or 2) to Austenitic Stainless Steel (M-8/P-8/S-8, Group 1), 1/16
through 1-1/2 inch Thick, ER309(L), As-Welded Condition, Primarily Pipe Applications
B2.1-1/8-228:2002 Standard Welding Procedure Specification (SWPS) for Shielded Metal Arc Welding of Car-
bon Steel (M-1/P-1/S-1, Groups 1 or 2) to Austenitic Stainless Steel (M-8/P-8/S-8, Group 1),
1/8 through 1-1/2 inch Thick, E309(L)-15, -16, or -17, As-Welded Condition, Primarily Pipe
Applications
B2.1-1/8-229:2002 Standard Welding Procedure Specification (SWPS) for Gas Tungsten Arc Welding followed
by Shielded Metal Arc Welding of Carbon Steel (M-1/P-1/S-1, Groups 1 or 2) to Austenitic
Stainless Steel (M-8/P-8/S-8, Group 1), 1/8 through 1-1/2 inch Thick, ER309(L) and
E309(L)-15, -16, or -17, As-Welded Condition, Primarily Pipe Applications
B2.1-1/8-230:2002 Standard Welding Procedure Specification (SWPS) for Gas Tungsten Arc Welding with Con-
sumable Insert Root of Carbon Steel (M-1/P-1/S-1, Groups 1 or 2) to Austenitic Stainless
Steel (M-8/P-8/S-8, Group 1), 1/16 through 1-1/2 inch Thick, IN309 and ER309(L), As-Welded
Condition, Primarily Pipe Applications
B2.1-1/8-231:2002 Standard Welding Procedure Specification (SWPS) for Gas Tungsten Arc Welding with Con-
sumable Insert Root followed by Shielded Metal Arc Welding of Carbon Steel (M-1/P-1/S-1,
Groups 1 or 2) to Austenitic Stainless Steel (M-8/P-8/S-8, Group 1), 1/8 through 1-1/2 inch
Thick, IN309, ER309, and E309-15, -16, or -17, or IN309, ER309(L), and ER309(L)-15, -16,
or -17, As-Welded Condition, Primarily Pipe Applications
For ordering information, contact Global Engineering Documents, an Information Handling Services (IHS) Group company,
15 Inverness Way East, Englewood, Colorado 80112-5776; telephones: (800) 854-7179, (303) 397-7956; fax (303) 397-
2740; Internet: www. global.ihs.com.
Permission to reproduce for intra-company use only is granted by the American Welding Society
Copyright American Welding Society
Provided by IHS under license with AWS Licensee=ExxonMobil/1890500101
No reproduction or networking permitted without license from IHS Not for Resale, 02/03/2007 11:45:04 MST