Documente Academic
Documente Profesional
Documente Cultură
SEISMIC
BRACING GUIDE
PARTITIONS & CEILINGS
NEW ZEALAND
SECOND EDITION
Available from
CONTENTS/
About us 2
TRACKLOK® Range 3
Features and Benefits 4
Install Instructions & Plenum Guidance 5
TRACKLOK® Plan & Elevations 6
Seismic Zone Chart 7
Setout Chart One 8
Setout Chart Two 9
Setout Chart Three 10
GAPLOK 11
TRACKLOK® FLAT 13
Features and Benefits 14
Install Instructions 15
TRACKLOK® FLAT Plan & Elevations 15
TRACKLOK® FLAT Partition Elevations 16
Top Connections
Concrete Connection Detail 18
Comflor Connection Detail 19
Parallel Steel Connection Detail 20
Perpendicular Steel Connection Detail 21
Parallel Timber Connection Detail 22
Perpendicular Timber Connection Detail 23
Bridging and Bulkheads
Parallel Bridge Detail 24
Perpendicular Bridge Detail 25
Parallel & Perpendicular Bridge Notes 26
Service Bridge Detail 27
Service Bridge Notes 28
Bulkhead Bracing Detail 29
Bulkhead Bracing Notes 30
GRIDLOK® 31
GRIDLOK® Range 32
Features and Benefits 33
Install Instructions & Plenum Guidance 34
GRIDLOK® Isometric 35
GRIDLOK® Peak Form Isometric 36
GRIDLOK® Kwikloc Isometric 37
GRIDLOK® Top Cross Rail (TCR) Isometric 38
GRIDLOK® C Channel Isometric 39
GRIDLOK® Unigrid Isometric 40
Accessories
BC45 Connectors 42
BC90 Connectors 43
Appendix – TRACKLOK® 44
Appendix – GRIDLOK® 46
Terms & Conditions 48
ABOUT US/ TRACKLOK RANGE/
This range of pre-engineered, off the shelf TRACKLOK® Ltd continues to help the
solutions enables architects, designers, construction industry “build it better”. TRACKLOK® - TRACKLOK® for new builds, allows you to connect directly
structural engineers, construction companies through the partition head, separating wall from ceiling. Tested to provide
TRACKLOK Ltd works with like-minded
®
and installers to mitigate the risk of non- structural and seismic performance for internal non-structural walls and glazing
industry leaders worldwide. We work with lines. Steel head track must be a minimum of .75 BMT, while aluminium head
structural failure in commercial buildings.
industry organisations, regulators and track must have a minimum material thickness of 1.3mm. Utilises steel stud for
TRACKLOK® Ltd provides bracing options governments to ensure design through to bracing stock. Using 10-gauge wafer tek screws to attach bracing stock to the
to take the guesswork and liability out of build consistency and compliance. unit and top connectors. Set out charts provide clear guidance for placement.
securing non-structural walls and ceilings. Utilised in IL2, IL3 and IL4 buildings. STOCK CODE: SPT-10
Both the TRACKLOK® and GRIDLOK® range TRACKLOK® RETRO - Bringing an existing fit out up to seismic code, adding
of connections have been designed to value to your clients existing fit out, or create time efficiencies by bracing
comply with building code requirements and after lining. TRACKLOK® RETRO is an effective way to retroactively attach
ceiling manufacturers warranties. to the partition head using 10-gauge wafer tek screws. Steel head track
must be a minimum of .75 BMT, while aluminium head track must have a
The TRACKLOK® system for walls and the minimum material thickness of 1.3mm. Utilises steel stud for bracing stock.
GRIDLOK® system for ceilings are perfect Using 10-gauge wafer tek screws to attach bracing stock to the unit and top
examples of applying logic, innovation and connectors. Disengage walls and ceilings by using TRACKLOK® RETRO. Set
best practice to mitigate risk and improve out charts provide clear guidance for placement. Utilised in IL2, IL3 and IL4
building resilience. buildings. STOCK CODE: SPT-10R
Interior fit out is a complicated, multi trade TRACKLOK® TIMBA - Timber framed walls and timber top plates present
a unique bracing challenge. TRACKLOK® TIMBA is a uniquely designed
discipline, which requires cost and time
solution, allowing the appropriate bracing while ensuring maximum
efficient solutions to standard practices. connection to timber using minimum 10-gauge 35mm wood screws. Timber
The use of these products allows wall and top plate must be minimum 90 x 45mm SG8 Radiata Pine or Douglas Fir.
ceiling systems to perform independently as Locator notch provides perfect placement every time. Utilises steel stud for
designed. bracing stock. Using 10-gauge wafer tek screws to attach bracing stock to the
unit and top connectors. Set out charts provide clear guidance for placement.
Utilised in IL2, IL3 and IL4 buildings. STOCK CODE: SPT-10T
TRACKLOK® VERT - Service clashes are inevitable and although the
TRACKLOK® range provides flexibility with bracing angles from 30° to 60°
there will always be some situations where this is not enough. TRACKLOK®
VERT gives the installer a tool to use a vertical brace on one arm allowing for
the ultimate in clash avoidance. Steel head track must be a minimum of .75
BMT, while aluminium head track must have a minimum material thickness
of 1.3mm. Utilises steel stud for bracing stock. Using 10-gauge wafer tek
screws to attach bracing stock to the unit and top connectors. Also, available
with RETRO and TIMBA bases. Set out charts provide clear guidance for
placement. Utilised in IL2, IL3 and IL4 buildings. STOCK CODE: SPT-10V
2 NZ EDITION FEB 2018 NZ EDITION FEB 2018 3
FEATURES AND BENEFITS/ INSTALL INSTRUCTIONS/
• All products have been tested with steel OBJECTIVES/ 1/ Set out head track (clamp or screw temporarily) must be min .75 BMT steel
and aluminium head track to ensure or min 1.3mm aluminium.
• Prevent injury caused by failure of all types
compatibility.
of internal partition wall and glazing line 2/ Measure TRACKLOK® placements (refer to TRACKLOK® specification sheet).
• Steel head track must be a minimum of systems due to seismic activity.
.75 BMT, while aluminium head track must 3/ Create 30mm - 40mm clearance hole in ceiling tile with holesaw (pilot bit marks centre
• Prevent loss of amenity caused by the
have a minimum material thickness of point on head track).
behaviour of all types of internal partition
1.3mm.
wall and glazing line systems during 4/ Enlarge pilot hole in head track to 9mm. RETRO affixed to head track with 10-gauge
• Full wall system, quasi static testing seismic activity. wafer tek screws. TIMBA affixed to 90mm x 45mm timber top plate with minimum
provides specifiers with confidence.
10-gauge 35mm wood screws.
• Protect property and structures from
• Provides seismic separation between wall physical damage caused by the failure
of
and ceiling, preserving warranties.
5/ Bolt TRACKLOK® firmly to head track using washer and bolt provided.
all types of internal partition wall and
• Ensures validity of installers PS3.
glazing line systems due to seismic activity.
6/ Measure distance to structure from fly plate below screw holes and cut your brace
• Tested under ULS and SLS loads to ensure • Preserve ceiling manufacturer’s warranty material to length as per chart provided.
longevity of performance.
by providing required seismic separation 7/ Connect bracing material to TRACKLOK® fly brace and top plates.
• Unique design allows for 50mm of inter of partition and glazing lines from ceiling
story drift.
system.
8/ Fix TRACKLOK® top plates to structure with approved anchor.
• Top plate pivot points allow for 90mm of • Prevent business interruption caused by 9/ Remove temporary fixings.
in-line wall deflection.
the failure of all types of internal partition
wall and glazing line systems due to For further installation and limitation information please refer to TRACKLOK®
• Unique design allows for 20mm of wall
seismic activity.
Terms and Conditions on page 48 or at www.tracklok.com.
“spring back” in ULS event.
• Patented low profile connection bolt allows • Create efficiencies in construction of all
for clearance in glazing pockets.
types of internal partition wall and glazing
• Unit allows a 30° – 60° bracing angle to lines. PLENUM HEIGHT CHART/
mitigate service clashes.
• Unit tested to 45° off wall axis to mitigate COMPLIANCE/ PLENUM 64 OR 92MM X 64 OR 92MM X 0.55BMT 64 OR 92MM X 0.75BMT
service clashes.
• Complies to and provides compliance with HEIGHT MM/ 0.55BMT STUDS*/ BOXED STUDS*/ BOXED STUDS*/
• TRACKLOK® VERT allows vertical bracing NZS 1170.5, AS1170.4 and AS/NZS 4219.
0 - 2000 241kgf 241kgf 241kgf
to mitigate service clashes.
• Provides compliance with NZ Building 2000 - 3150 - 241kgf 241kgf
• TRACKLOK® RETRO allows for Code Clause B1 – Structure, B2 – Durability,
3150 - 4000 - - 241kgf
retroactive
installation using 10-gauge F2 – Hazardous Building Materials.
wafer tek screws to affix to head track.
• Contributes to compliance with NZ * Stud to TRACKLOK connection to consist of 6/10g tek screws.
®
TIMBER JOISTS
- POWER BOLT
- WEDGE BOLT
STEEL BEAMS
- HST STUDS
WHANGAREI
HEIGHT < 3M < 6M < 9M 9M +
BOLT/NUT
BOLT/NUT
POWERS
RAMSET
AUCKLAND
ZONE 1 CHART 1 CHART 1 CHART 1 CHART 1
HILTI
ZONE 2 CHART 1 CHART 1 CHART 2 CHART 2
NOTES ROTORUA
1/ Height (m) is to floor above partition.
NEW PLYMOUTH
TO LENGTH REQUIRED & FIX TO SUPPLIED BRACKETS
ELEVATION
per m2 and for Importance Level
ENDELEVATION
3 and 4 Buildings please contact
PLAN VIEW
TRACKLOK® Ltd.
WELLINGTON
NELSON
END
CHRISTCHURCH
PILOT HOLE TO BRACKET
TILE & FIX PARTITION VIA
SAW THROUGH CEILING
DRILL HOLE WITH HOLE
ZONE 1
QUEENSTOWN
ZONE 2
ZONE 3
DUNEDIN
10 GAUGE WAFER
TEK SCREWS
INVERCARGILL
Door Door
Door Door
Door Door
NOTES NOTES
1/ Height (m) is to floor above partition. 1/ Height (m) is to floor above partition.
2/ Spacings based on horizontal load < 0.75 kN/m 2/ Spacings based on horizontal load < 1.20 kN/m
3/ Allows for 50mm of inter story drift. 3/ Allows for 50mm of inter story drift.
Door
4/ For wall heights up to 3.0m. 4/ For wall heights up to 3.0m.
Door
5/ For wall weights up to 40kg per m2. 5/ For wall weights up to 40kg per m2.
6/ Each dashed line represents one brace. 6/ Each dashed line represents one brace.
For wall weights heavier than 40kg per m2 and for Importance Level 3 and 4 Buildings For wall weights heavier than 40kg per m2 and for Importance Level 3 and 4 Buildings
please contact TRACKLOK® Ltd. please contact TRACKLOK® Ltd.
8 NZ EDITION FEB 2018 NZ EDITION FEB 2018 9
CHART THREE/ GAPLOK/
Door Door
Door Door
On occasion, a partition wall or a glazing line placement may coincide with the main runner
Door
or nog of a two-way grid ceiling system. In this instance, there would be no way for a
TRACKLOK® to pass through the grid, with the required clearance. GAPLOK has been carefully
designed, developed and engineered to allow installers to accommodate TRACKLOK®
Door bracing in these instances. GAPLOK provides for 316kgf of capacity.
GAPLOK allows installers to take a 40mm section out of the grid. Clamp GAPLOK to either
side of the remaining grid section to bridge the gap, reinstate the grid’s structural integrity
BRACING BETWEEN RETURN WALLS and allow the clearance required of the TRACKLOK® unit.
STOCK CODE: GGP-10
NOTES
1/ Height (m) is to floor above partition.
2/ Spacings based on horizontal load < 1.60 kN/m
New Zealand’s Ministry of Social Development is located at 56 The Terrace, Wellington. This is an
3/ Allows for 50mm of inter story drift.
area prone to seismic activity and can be difficult to design for, however the MSD is an important post
4/ For wall heights up to 3.0m. earthquake agency. TRACKLOK® secured internal, non-structural walls and glazing lines within the building,
5/ For wall weights up to 40kg per m2. as it experienced the forces generated by the 2016 7.8 magnitude Kaikoura earthquake, 400kms to the
south. Great design and engineering have allowed the MSD to continue its work in a safe environment,
Door 6/ Each dashed line represents one brace. post earthquake and TRACKLOK® is proud to have played its part.
For wall weights heavier than 40kg per m2 and for Importance Level 3 and 4 Buildings
please contact TRACKLOK® Ltd.
10 NZ EDITION FEB 2018 NZ EDITION FEB 2018 11
TRACKLOK FLAT/
TRACKLOK® FLAT
Wall bracing can need to allow for large amounts of vertical deflection greater than that
accommodated by wall build up and/or deflection track. Also, projects with a very high
plenum can be impractical to brace. While intense services can leave an installer with no
space through which to install a wall brace. These three situations led to the design and
development of the engineered solution TRACKLOK® FLAT.
TRACKLOK® FLAT utilises the benefits of the TRACKLOK® design and applies it to horizontally
brace partition walls. Employing the principles of a “dragon tie” in residential terms,
TRACKLOK® FLAT can brace one wall off another. TRACKLOK® FLAT is revolutionary.
Ensuring seismic separation, providing ceiling clearance and featuring unique adjustability to
clear troffer lights, sprinkler pipes and services - TRACKLOK® FLAT is an elegant, yet robust
solution. Available in RETRO and TIMBA bases to ensure ease of use.
Steel head track must be a minimum of .75 BMT, while aluminium head track must have a
minimum material thickness of 1.3mm. RETRO affixed to head track with 10-gauge wafer tek
screws. TIMBA affixed to 90mm x 45mm timber top plate with minimum 10-gauge 35mm
wood screws.
STOCK CODE: SPT-10F / SPT-10FR / SPT-10FT
• All products have been tested with steel OBJECTIVES/ 1/ Set out head track (clamp or screw temporarily) must be min .75 BMT steel or min 1.3mm
and aluminium head track to ensure aluminium.
• Prevent injury caused by failure of all types
compatibility.
of internal partition wall and glazing line 2/ Measure TRACKLOK® FLAT placements (refer to TRACKLOK® FLAT Set Out Guidance).
• Steel head track must be a minimum
systems due to seismic activity.
of .75 BMT, while aluminium head track 3/ Create 30mm - 40mm clearance hole in ceiling tile with holesaw (pilot bit marks centre
• Prevent loss of amenity caused by the
must have a minimum material thickness point on head track).
behaviour of all types of internal partition
of 1.3mm.
wall and glazing line systems during 4/ Enlarge pilot hole in head track to 9mm. RETRO affixed to head track with 10-gauge
• Full wall system, quasi static testing wafer tek screws. TIMBA affixed to 90mm x 45mm timber top plate with minimum
seismic activity.
provides specifiers with confidence.
10-gauge 35mm wood screws.
• Protect property and structures from
• Provides seismic separation between wall
physical damage caused by the failure
of 5/ Connect first TRACKLOK® FLAT to head track firmly with attachment method supplied.
and ceiling, preserving warranties.
all types of internal partition wall and
• Ensures validity of installers PS3.
glazing line systems due to seismic activity.
6/ Measure distance from TRACKLOK® FLAT unit one to unit two and cut 2x lengths of steel
• Tested under ULS and SLS loads to ensure • Preserve ceiling manufacturer’s warranty stud (.75 BMT) to form box section.
longevity of performance.
by providing required seismic separation 7/ Connect bracing material to each TRACKLOK® FLAT unit filling all screw holes.
• Unique design allows for unlimited inter of partition and glazing lines from ceiling
story drift.
system.
8/ Screw off plasterboard top and bottom and silicone glazing into all channels at 300mm
• Patented low profile connection bolt allows centres.
• Prevent business interruption caused by
for clearance in glazing pockets.
the failure of all types of internal partition 9/ Remove temporary fixings.
• TRACKLOK® FLAT can be retroactively wall and glazing line systems due to
For further installation and limitation information please refer to TRACKLOK®
installed when combined with a RETRO seismic activity.
Terms and Conditions on page 48 or at www.tracklok.com.
fitting and using 10-gauge wafer tek screws • Create efficiencies in construction of all
to affix to head track.
types of internal partition wall and glazing
• TRACKLOK® FLAT can brace timber framed lines.
TRACKLOK FLAT ELEVATIONS/
walls when combined with a TIMBA fitting 64mm or 92mm 0.75 BMT
STUD BOXED
and using 35mm 10-gauge wood screws to COMPLIANCE/
affix to timber top plate.
• Complies to and provides compliance with
• Allows for 64mm and 92mm boxed bracing
NZS 1170.5, AS1170.4 and AS/NZS 4219.
to be used, reducing waste on site.
• Provides compliance with NZ Building
Code Clause B1 – Structure, B2 – Durability,
F2 – Hazardous Building Materials.
• Contributes to compliance with NZ
Building Code Clause F6 – Visibility in
Escape Routes, Clause D1 – Access Routes.
DRILL HOLE WITH HOLE
SAW THROUGH CEILING
TILE & FIX PARTITION VIA
PILOT HOLE TO BRACKET
APPLICATIONS/
• Importance Level 2, 3 and 4 Buildings
• Hospitals
• Commercial Interiors END ELEVATION
SIDE ELEVATION SIDEELEVATION
END ELEVATION
• Schools
PLAN VIEW
14 NZ EDITION FEB 2018 NZ EDITION FEB 2018 15
TRACKLOK FLAT PARTITION ELEVATIONS/ TRACKLOK FLAT PARTITION ELEVATIONS/
55mm(min)
35mm(min)
50mm(min)
35mm(min)
50mm(min)
FIX STEEL STUD TO SUPPLIED BRACKET WITH FIX STEEL STUD TO SUPPLIED BRACKET WITH
6x 10G WAFER TEK SCREWS (TRACKLOK®) 6x 10G WAFER TEK SCREWS (TRACKLOK®)
OR 4x 10G WAFER TEK SCREWS (GRIDLOK®) OR 4x 10G WAFER TEK SCREWS (GRIDLOK®)
M6
M8HILTI
HILTI HUS-H6
HST STUDSCREW ANCHOR
EXPANSION OR
ANCHOR
SIMILAR SEISMICALLY
OR SIMILAR APPROVED
SEISMICALLY ANCHOR
APPROVED
INSTALL
ANCHOR AS PER
INSTALL ASMANUFACTURER’S
PER MANUFACTURER’S
SPECIFICATION
SPECIFICATION
M6 55mm(min)
M8 50mm(min)
50mm(min)
FIX FIX
STEEL STUD
STEEL TO SUPPLIED
STUD BRACKET
TO SUPPLIED WITH
BRACKET
6x 10G WAFER
WITH TEK
6X 10G SCREWS
WAFER TEK(TRACKLOK
SCREWS ®)
OR 4x 10G WAFER TEK SCREWS (GRIDLOK®)
20 NZ EDITION EDITION
AUSTRALIAN FEB 2018 AUGUST 2017 NZ EDITION FEB 2018
AUSTRALIAN EDITION AUGUST 2017
21
21
PARALLEL TIMBER CONNECTION DETAILS/ PERPENDICULARTIMBER
PERPENDICULAR TIMBERCONNECTION
CONNECTIONDETAILS/
DETAILS/
25mm(min)
30mm(min)
40mm(min) BOLTFIXING
BOLT FIXING
22 NZ EDITION EDITION
AUSTRALIAN FEB 2018 AUGUST 2017 AUSTRALIAN NZ
EDITION
EDITIONAUGUST
FEB 2018 23
201723
24
NZ EDITION
REFER TO SPAN NOTES ON PAGE 26
FEB 2018
STRUCTURE STEEL STUD
PURLIN 1.15BMT(MIN) -
FIX TO TOP HALF OF
PURLIN WEB
PARALLEL BRIDGE DETAIL/
GRIDLOK® UNIGRID
Designed and tested to provide a consistent maximum 280kg/f of bracing
capacity to the Armstrong UNIGRID system. Consistency in load capabilities
is the key feature, while the ease of installation will dramatically reduce install
times. Plenum height chart provide guidance on steel stud BMT required
for bracing arms. Get a better result in less time. Features the ability to rotate
the unit though 360° minimising service clashes. STOCK CODE: GRD-10U
4/ nsure ceiling grid is at correct height, measure and cut steel stud, as per chart provided
E
and connect to vertical arm.
6/ ut two 45° steel studs as per plenum chart provided, attach to 45° top connectors and
C
45° GRIDLOK® arms.
Refer to Plenum
A
34 of this guide
screw holes are filled.
Refer to Plenum
34 of this guide
600 - 1000 250kgf 280kgf 250kgf 280kgf
1000 - 1400 250kgf 280kgf 250kgf 280kgf
1400 - 1800 160kgf 270kgf 250kgf 280kgf
50 Max.
1800 - 2200 110kgf 180kgf 250kgf 280kgf
2200 -2600 80kgf 130kgf 250kgf 280kgf
2600 - 3000 60kgf 100kgf 190kgf 280kgf
34 of this guide
* Stud to GRIDLOK connection to consist of 4/10g tek screws
®
NZ EDITION
Height Chart on page
34 of this guide
FEB 2018
Fix to Structure in Accordance
with GRIDLOK® Specification
Refer to Plenum
Refer to Plenum Height Chart on page
Height Chart on page 34 of this guide
34 of this guide
GRIDLOK® PEAKFORM/
50 Max.
Refer to Plenum
Height Chart on page
34 of this guide
50 Max.
NZ EDITION
NZ EDITION
34 of this guide
FEB 2018
Fix to Structure in Accordance
with GRIDLOK® Specification
Refer to Plenum
Refer to Plenum Height Chart on page
Height Chart on page 34 of this guide
34 of this guide
Refer to Plenum
Height Chart on page
34 of this guide
NZ EDITION
34 of this guide
FEB 2018
Fix to Structure in Accordance
with GRIDLOK® Specification
Refer to Plenum
Refer to Plenum Height Chart on page
Height Chart on page 34 of this guide
34 of this guide
GRIDLOK® UNIGRID/
NZ EDITION
FEB 2018
41
ACCESSORIES - BC45/ ACCESSORIES - BC90/
OVERVIEW Note this is for ULS design as per “Loading The following assumptions are used: TRACKLOK® components have the following
This report outlines the methods that shall Methodology” section in manual. mu = 1.0 as • The partition wall is sufficiently supported ratings:
be adopted for Specific Engineering Design connections/buckling is limiting. AS 4600 has along the floor track TRACKLOK® 2.37kN
(SED) for TRACKLOK® bracing systems for a maximum value of 1.25 and we have taken • The partition wall has sufficient shear TRACKLOK® RETRO 2.37kN
non-load bearing internal walls. Design the conservative option of 1.0 as per 8.7.1 of resistance in plane TRACKLOK® TIMBA 2.37kN
shall be carried out in accordance with B1/ NZS 1170.5 for non-ductile connections. • The headtrack and wall studs have sufficient TRACKLOK® FLAT 2.37kN
VM1 of the New Zealand Building Code. capacity to transfer load between braces TRACKLOK® VERT 2.37kN
The partition studs and connections are not Wind Action Assumptions Table 1 below, shows TRACKLOK® ratings
considered as part of this scope, however AS/NZS 1170.2 shall be used to determine Brace Demand based on plenum height.
need to be considered within the design. the horizontal and vertical design actions The bracing demand shall be within the
upon the system. The following should be permissible ratings of each TRACKLOK® DESIGN VERIFICATION
LOADING METHODOLOGY adopted for internal walls that do not form a component. Specific engineering design The following standards should be used to
Loading Standards permanent seal: around studs and structure fixings are validate specific engineering design:
The following standards shall be used to • Net Pressure Coefficient, Cfig = ± 0.3 permissible, so long as the demand does not • Steel Studs & Connections: AS/NZS
determine the design actions on the systems: • Dynamic Response Factor, Cdyn = 1.0 exceed the TRACKLOK® ratings. TRACKLOK® 4600:2005 - Cold-Formed Steel Structure
• AS/NZS 1170.0:2002 - Structural Design components are rated as shown in Figure 2 • Timber Studs & Connections: NZS
Actions - General Principles Note that external walls will have a higher net below. Bracing angles shall be considered 3603:1993 - Timber Structures Standard
• AS/NZS 1170.2:2011 - Structural Design pressure coefficient and shall be considered to determine loading in other parts of the • Concrete Anchors: NZS 3101:2006 -
Actions - Wind Actions as part of specific engineering design. design. Concrete Structures Standard
• NZS 1170.5:2004 - Structural Design Actions
- Earthquake Actions Live Actions Assumptions
Soft Body Impact as per Table C1 of AS/NZS
Load combinations shall be applied as 1170.0 shall be considered as follows:
per AS/NZS 1170.0. ULS design shall be • Q = 0.7kN
implemented for the bracing elements,
and SLS deflection requirements should be DESIGN METHODOLOGY
considered for items such as the wall studs Tributary Area
and headtrack to limit damage of the wall. The tributary area method shall be used to
determine the bracing demand. The braces
Seismic Action Assumptions are designed to withstand out of plane loads,
NZS 1170.5 - Section 8 shall be used to as shown in Figure 1 below.
determine the horizontal and vertical design
actions upon the system. The following
assumption should be adopted for bracing
design:
Figure 2 - Illustration of TRACKLOK® component
• Site Subsoil Class C ratings
• Period, T < 0.75s
Ceilings/partitions should be designed
for < 0.75s to give the most adverse Table 1: Permissible horizontal loads in accordance with AS/NZS 4600
component spectral shape coefficient PLENUM 64 OR 92MM X 64 OR 92MM X 0.55BMT 64 OR 92MM X 0.75BMT
Ci(Tp) as per Section 8.4 of NZS 1170.5. HEIGHT MM/ 0.55BMT STUDS*/ BOXED STUDS*/ BOXED STUDS*/
Hard to determine the period of a
0 - 2000 241kgf/2.37kN 241kgf/2.37kN 241kgf/2.37kN
suspended ceiling/partition, so have taken
the conservative option. 2000 - 3150 - 241kgf/2.37kN 241kgf/2.37kN
• Near Fault Factor, N(T,D) = 1.0 3150 - 4000 - - 241kgf/2.37kN
• Ductility, μ = 1.0
• Part Category P.2/P.3 (ULS Design) Figure 1 - Tributary area diagram for design * Stud to TRACKLOK® connection to consist of 6/10g tek screws.
OVERVIEW • Net Pressure Coefficient, Cfig = ± 0.3 Brace Demand DESIGN VERIFICATION
This report outlines the methods that shall • Dynamic Response Factor, Cdyn = 1.0 The bracing demand shall be within the The following standards should be used to
be adopted for Specific Engineering Design permissible ratings of each GRIDILOK® validate specific engineering design:
(SED) for seismic bracing using GRIDLOK® for Note that external ceilings and soffits have a component. Specific engineering design •S teel Studs & Connections: AS/NZS
suspended ceilings. Design shall be carried higher net pressure coefficient and shall be around studs and structure fixings are 4600:2005 - Cold-Formed Steel Structures
out in accordance with B1/VM1 of the New considered as part of specific engineering permissible, so long as the demand does not •T imber Studs & Connections: NZS
Zealand Building Code. Vertical loading and design. exceed the maximum GRIDLOK® rating of 3603:1993 - Timber Structures Standard
specific suspended ceiling system design is 280kgf. •C oncrete Anchors: NZS 3101:2006 -
not covered within this scope. DESIGN METHODOLOGY Concrete Structures Standard
Tributary Area Tributary Area Demand < GRIDLOK®
LOADING METHODOLOGY The tributary area method shall be used to Capacity
Loading Standards determine the bracing demand. The braces
The following standards shall be used to are designed to withstand lateral loads, Table 1 below, shows GRIDLOK® ratings
determine the design actions on the systems: as shown in Figure 1 below. The following based on plenum height.
• NZS 1170.5:2004 - Structural Design Actions assumptions are used:
- Earthquake Actions •A minimum of two braces are used for Table 1: Permissible horizontal loads in accordance with AS/NZS 4600
• AS/NZS 1170.2:2011 - Structural Design stability
Actions - Wind Action •A ll ceiling perimeters are to have a floating PLENUM 64 X 0.55BMT 92 X 0.75BMT 64 X 0.55BMT 92 X 0.75BMT
• AS/NZS 2785:2000 - Suspended Ceilings - connection to allow for inter-story drift HEIGHT MM/ STUDS*/ STUDS*/ BOXED STUDS*/ BOXED STUDS*/
Design and Install •M aximum ceiling tee lengths to be checked 0 - 600 250kgf 280kgf 250kgf 280kgf
as per manufacturer’s requirements
Load combinations shall be applied as •V ertical suspension as per manufacturer’s 600 - 1000 250kgf 280kgf 250kgf 280kgf
per AS/NZS 2785. ULS design shall be requirements 1000 - 1400 250kgf 280kgf 250kgf 280kgf
implemented for the bracing elements as per •T he ceiling behaves as a rigid diaphragm 1400 - 1800 160kgf 270kgf 250kgf 280kgf
Table 8.1 of NZS 1170. •M anufacturer seismic requirements are
1800 - 2200 110kgf 180kgf 250kgf 280kgf
complied with
Seismic Action Assumptions 2200 -2600 80kgf 130kgf 250kgf 280kgf
NZS 1170.5 - Section 8 shall be used to 2600 - 3000 60kgf 100kgf 190kgf 280kgf
determine the horizontal and vertical design
3000 - 3500 - - 140kgf 280kgf
actions upon the system. The following
assumption should be adopted for bracing 3500 - 4000 - - 100kgf 210kgf
design:
* Stud to GRIDLOK connection to consist of 4/10g tek screws
®
• Site Subsoil Class C
• Period, T < 0.4s
• Near Fault Factor, N(T,D) = 1.0
• Ductility, μ = 1.0
• Part Category P.2/P.3 (ULS Design)
www.potters.co.nz
0800 POTTERS
specsupport@potters.co.nz
TECH SUPPORT
Ph +64 21 170 8734
plans@tracklok.co.nz
TRACKLOK Ltd
PO BOX 31270
Milford
Auckland 0620
www.tracklok.com