Sunteți pe pagina 1din 3

Multifunction Timers

Types DMB51
Product Description
Multi-voltage timer with 7 knob-selectable functions and 7
knob-selectable time ranges within 0.1s and 100h.
Housing 17.5 mm wide suitable for back and front panel
mounting. Wide power supply range: 12 to 240 VAC/DC.

Property
• Selectable time range 0.1 s to 100 h
• 7 knob selectable functions:
Op - delay on operate
In - interval
Io - interval on trigger open
Id - double interval
Dr - delay on release
R - symmetrical recycler ON first
Rb - symmetrical recycler OFF first
• Automatic or manual start
• Repeatability: ≤ 0.2%
• Output: 5 A SPDT
• For mounting on DIN-rail in accordance with DIN/EN 50 022
• 17.5 mm DIN-rail housing (DIN 43880)
• Combined AC and DC power supply
• LED indication for relay status and power supply ON

Type Selection Output Specifications


Mounting Output Housing Supply: Output SPDT
Rated insulation voltage 250 VAC (rms)
DIN-rail SPDT Mini-D 12 to 240 VAC/DC
Contact Ratings (AgSnO2) μ

Supply Specifications Resistive loads AC 1 5 A @ 250 VAC


DC 12 5 A @ 24 VDC
Power supply Overvoltage cat. II Small inductive loads AC 15 2.5 A @ 250 VAC
Rated operational voltage (IEC 60664, IEC 60038) DC 13 2.5 A @ 24 VDC
through terminals: 12 to 240 VDC + 10% -15%
and 12 to 240 VAC Mechanical life ≥ 30 x 106 operations
+ 10% -15%, 45 to 65 Hz Electrical life ≥ 105 operations
Voltage interruption ≤ 10 ms (at 5 A, 250 V, cos ϕ = 1)
Rated operational power Operating frequency < 7200 operations/h
AC supply: 4 VA Dielectric strength
DC supply: 1.5 W Dielectric voltage 2 kVAC (rms)
Rated impulse withstand
General Specifications voltage 2.5 kV (1.2/50 μs)

Power ON delay ≤ 100 ms Time Specifications


Indication for
Power supply ON LED, green Time ranges
Output relays ON LED, yellow Knob selectable 0.1 to 1 s ,1 to 10 s
(flashing when timing) 6 to 60 s ,60 to 600 s
0.1 to 1 h ,1 to 10 h
Environment (EN 60529)
Degree of protection IP 20 10 to 100 h
Pollution degree 2 (IEC 60664) Setting accuracy ≤ 5%
Operating temperature -20° to +60°C, R.H. < 95%
Storage temperature -30° to +80°C, R.H. < 95% Repeatability ≤ 0.2%
Housing Time variation
Dimensions 17.5 x 81 x 67.2 mm Within rated power supply ≤ 0.05%/V
Material PA66 Within ambient temperature ≤ 0.2%/°C
Weight 75 g Reset
Manual reset of time and/or Close the trigger contact
Screw terminals relay between pins A1 and Y1
Tightening torque Max. 0.5 Nm according to Pulse duration ≥ 100 ms
IEC EN 60947 Power supply interruption ≥ 200 ms
Approvals UL, CSA Automatic start Connect pins A1 and Y1
RINA
CE Marking Yes
EMC Electromagnetic Compatibillity
Immunity According to EN 61000-6-2
Emissions According to EN 61000-6-3
1
www.dold-relay.com
DMB51CW24

Time Setting
Upper knob: Centre knob:
Setting of function: Time setting on relative scale:
Op - delay on operate 1 to 10 with respect to the
In - interval chosen range.
Io - interval on trigger open
Lower knob:
Id - double interval
Setting of time range
Dr - delay on release
R - symmetrical recycler
(ON first)
Rb - symmetrical recycler
(OFF first)

Mode of Operation
Function Op Function Io Function Dr Function Rb
Delay on operate Interval on trigger open Delay on release Symmetrical recycler,
The time period begins as The relay operates and the The relay operates as soon OFF-time period first
soon as the trigger contact time period begins as soon as the trigger contact is The time period begins as
is closed. as the trigger contact is closed. The time period soon as the input contact is
At the end of the set delay opened. At the end of the begins when the trigger con- closed. The relay is OFF
time the relay operates and set delay or when the power tact is opened. The relay during the set delay period,
does not release until the supply is disconnected the releases at the end of the after this time it operates for
trigger contact is closed relay releases. The relay set delay time or when the the same time period. This
again or the power supply is operates again when the power supply is disconnect- sequence continues with
disconnected. If the trigger trigger contact is opened ed. The relay operates again equal OFF- and ON-time
contact is closed before the again. If the trigger contact when the input contact is periods until the power sup-
end of the delay time, the is opened before the end of closed again. If it is opened ply is interrupted.
device resets and a new the delay time the relay before the end of the delay
time period starts. keeps ON and a new time time the relay keeps ON, a Additional Load
period begins. new time period begins as It's possible to wire an addi-
Function In soon as the contact is tional load (i.e. a relay)
Function Id between pins Y1 and A2,
Interval Double interval closed again.
The relay operates and the driven by the trigger contact
The relay operates and the Function R without damaging the
time period begins as soon time period begins as soon
as the trigger contact is Symmetrical recycler, ON- device.
as the trigger contact is time period first
closed. The relay releases at closed. The relay releases at Yellow LED working
the end of this period or The relay operates and the mode
the end of this period or time period begins as soon
when the power supply is when the power supply is Timing: Slow blinking
disconnected. The relay as the input contact is
disconnected. When the closed. After the set delay Relay ON: See operation
operates again when the trig- trigger contact is opened period the relay releases for diagrams
ger contact is closed again. If the relay operates again for
the trigger contact is closed the same time period. This Incorrect knobs position:
the set delay period. If the sequence continues with Fast blinking
before the end of the delay trigger contact is opened
time, the device resets and a equal ON- and OFF-time
before the end of the first periods until the power sup-
new time period starts. time period the second one ply is interrupted.
begins; if the trigger contact
is closed before the end of
the second time period the
device resets and the first
time period begins again.

Operating Diagrams
Function Op - Delay on operate - Manual start Function In - Interval - Manual start

Power supply Power supply

Trigger input Trigger input

ON T T ON T T
Relay ON Relay ON
OFF OFF

LED LED

2
www.dold-relay.com
DMB51CW24

Operating Diagrams (cont.)


Function Op - Delay on operate - Automatic start Function In - Interval - Automatic start

Power supply Power supply

ON T T ON T T
Relay ON Relay ON
OFF OFF

LED LED

Function Io - Interval on trigger open Function Id - Double interval

Power supply Power supply

Trigger input Trigger input

ON T T ON T T
Relay ON Relay ON

OFF OFF

LED
LED

Function Dr - Delay on release Function R - Symmetrical recycler (ON first)

Power supply Power supply

Trigger input Trigger input

ON T ON T T T T
Relay ON Relay ON
OFF OFF

LED LED

Function Rb - Symmetrical recycler (OFF first)

Power supply

Trigger input

ON T T T T
Relay ON
OFF

LED

Wiring Diagram Dimensions

17.5 67.2

18.7
A1 15 Y1
3 5.5
81

45

16 18 A2
2

3
www.dold-relay.com

S-ar putea să vă placă și