Documente Academic
Documente Profesional
Documente Cultură
RS485
+ Max. 64-point (ARM 8 units × 8-point)
Manual
Visit our webwite(www.autonics.com) to download 'GP Editor user manual' or 'SmartStudio user manual', 'SmartStudio
programing manual', 'LP Series command manual', 'LP-S070 user manual', 'GP, LP user manual for communication'.
● GP Editor user manual
It describes how to write screen data, and is about related usage of LP-S070 HMI function.
● SmartStudio user manual, SmartStudio programming manual, LP Series command manual
It contains install method and usage, commands, etc of SmartStudio.
● GP, LP user manual for communication : It describes connection for external devices such as PLC.
● LP-S070 user manual : It describes general information on the installation and usage of LP-S070 and system Contents.
Ordering information
Monitor Display Power I/O
Model Item Series Color Interface Module I/O connector
size unit supply composition
RS232C, RS422, Terminal block
LP-S070-T9D6-C5T
USB HOST connector
USB DEVICE, IN: Ribbon cable
LP-S070-T9D6-C5R TFT Ethernet All-in- 16points,
Logic 16,777,216 connector
S series 7 inch Color 24VDC one
panel color RS232C(2), USB Terminal block
LP-S070-T9D7-C5T LCD type OUT:
HOST 16points connector
USB DEVICE, Ribbon cable
LP-S070-T9D7-C5R Ethernet connector
R-26
Logic Panel
Specifications (A)
Photo
electric
Model LP-S070-T9D6-C5T LP-S070-T9D6-C5R LP-S070-T9D7-C5T LP-S070-T9D7-C5R sensor
I/O connector type Terminal block connector Ribbon cable connector Terminal block connector Ribbon cable connector (B)
Fiber
Power supply 24VDC optic
sensor
Allowable voltage range 90 to 110% of power supply
Power consumption Max. 7.2W (C)
Door/Area
LCD type 7 inch TFT Color LCD sensor
(D)
Display area 152.4mm×94.44mm Proximity
sensor
Color 16,777,216 color
LCD view angle Within each 50°/ 60°/ 65°/ 65° of top/bottom/left/right (E)
Pressure
Backlight White LED sensor
encoder
performance
Program capacity
8K step
performance
(I)
Processing time
Average : Approx. 2us/basic command, application command SSR/
Control
Power
I/O control type
Batch processing controller
Special function
Positioning function *Refer to LP-S070 user manual
Asynchronous method: Each port of RS232C, RS422 (K)
Serial interface Timer
Each port of RS232C, RS422 Two ports of RS232C
USB interface Each of USB Host, USB Device(Version 1.1) (L)
Ethernet interface IEEE802.3(U), 10/100Base-T Panel
meter
Real-time controller RTC embedded
(M)
Battery life cycle Approx. 3 years at 25℃ Tacho/
Speed/ Pulse
Insulated resistance Min. 100MΩ(at 500VDC megger) meter
※1: Language can be customized. ※Environment resistance is rated at no freezing or condensation. (S)
Field
Insulation method Photo coupler insulation Insulation method Photo coupler insulation
Voltage range 19.2 to 28.8VDC Voltage range 19.2 to 28.8VDC (U)
Other
Rated input voltage 24VDC Rated input voltage 24VDC
Contact X0 to X5: Approx. 10mA
Input resistance Max. load current 0.1A/1point, 1.6A/1COM
Contact X6 to XF: Approx. 4mA
Input resistance Contact X0 to X5: 2.2㏀, Contact X6 to XF: 5.6㏀ Max. voltage falling when ON Max. 0.2VDC
Response time 1ms Response time 1ms
Common method 16 points/1COM Common method 16 points/1COM
Acceptable wire 0.3 to 0.7mm2 Acceptable wire 0.3 to 0.7mm2
R-27
LP-S070
Functional description
Figure display Line, rectangle, circle, text, bitmap
Numeral display Displays the designated device as numerical value.(decimal, hexadecimal, octal, binary, real number)
ASCII display Displays the designated device value as ASCII character.
Time display Displays current time or date.
Alarm history Registers alarm history.
Alarm list Displays generated (not backed up) alarm.
Comment display Displays the designated comment as device status or value.
Lamp Displays lamp as device status.
Part display Displays the designated parts as device status and value.
Tags
Line graph Displays several device values with a graph of broken line.
Trend graph Displays change of device value for time with a graph of broken line.
Bar graph Displays a device value with a bar graph.
Statistic graph Displays a ratio of several device values with pie graph.
Panel meter Displays a device value as panel meter.
Touch key Screen is switched, word/bit device values are set when it touched.
Numeral input Configures user input value in device.
ASCII input Configures user input ASCII code value in device.
System information function Monitors/Controls LP operation from PLC.
Recipe function Reads/Writes several PLC device collectively.
Security function Only acceptable user can observe/operate important data.
Barcode read function Connects barcode reader, read barcode.
Floating alarm function Warning message is floated when alarm is generated.
Time operation Specific bit device is ON/OFF for designated day and time.
Overlap window Available to form dynamically overlapping another base screen on the base one.
Min. 175
※ Panel thickness
194 6.5 28.5 : Max. 4mm
● Fixing bracket
15
M4 BOLT
134
146
125
R-28
Logic Panel
(C)
Door/Area
sensor
Program
status LED (D)
Proximity
sensor
(E)
Pressure
sensor
(F)
Rotary
encoder
USB
LCD Screen RS422 RS422 Host (G)
Power terminal or or Ethernet USB Connector/
RS232C RS232C Device Socket
block -A -B
Fixing bracket
(2 slots is in upper side, 2 slot is in lower side) (H)
Temp.
controller
(I)
SSR/
Power
Mounting slot controller
for bracket
(J)
Counter
● Ethernet port : For connecting LAN cable and hub, use direct cable, and for connecting PC direcly, use cross cable.
● USB Device : It is used to upload and download project(It is required to install USB driver on PC), and when connect to
(K)
PC, it can be used as a USB memory(PC recognizes it as a removable disk). Timer
Installation (M)
Tacho/
Speed/ Pulse
1. Set LP-S070 in panel. meter
2. Set fixing brackets in 4 slots(2 slots is in upper side, 2 slots is in lower side).
(N)
Display
unit
(O)
Sensor
controller
(Upper side)
(P)
Switching
mode power
Mounting slot supply
for bracket
(Q)
Stepper
motor&
Driver&Controller
(S)
Field
3. Tighten fixing bracket with M4 screw driver and tightening torque is 0.3 to 0.5N.m.
network
device
(T)
Software
R-29
LP-S070
Input·Output wiring
LP-S070-T9D6(7)-C5R
● Input wiring(source type input module) ● Output wiring(sink type output module)
X0 0 8 X8 L Y0 0 8 Y8 L
X1 1 9 X9 L Y1 1 9 Y9 L
X2 2 A XA L Y2 2 A YA L
X3 3 B XB L Y3 B YB L
3
24VDC X4 4 C XC L Y4 YC L
4 C
X5 5 D XD L Y5 YD L
5 D
X6 6 E XE L Y6 YE L
6 E
X7
F XF L Y7 YF L
7 7 F
COM1 COM2
+ + + +
COM3 COM4
+ + 24VDC + +
LP-S070-T9D6(7)-C5T
● Input wiring(source type input module) ● Output wiring(sink type output module)
X0 0 L Y0 0
X1 1 L Y1 1
X2 2 L Y2 2
X3 3 L Y3 3
X4 4 L Y4 4
X5 5 L Y5 5
X6 6 L Y6 6
X7 7 L Y7 7
24VDC X8 Y8
8 L 8
X9 9 L Y9 9
XA A L YA A
XB B L YB B
XC C L YC C
XD D L YD D
XE E L YE E
XF F L YF F
COM1 + +
COM2 24VDC
+ -
※Check the pin number of the case before wiring.
Sold separately
I/O terminal block and I/O cable
Suitable I/O terminal block INPUT/OUTPUT Suitable I/O cable
AFS-H20 INPUT
CJ-HPHP20-V1N -1ANR
(Interface terminal block) OUTPUT
ABS-H16PA(TN)-NN
OUTPUT CJ-HPHP20-V1N -1APR
(Relay terminal block)
AFE4-H20-16LF INPUT CJ-HPHP20-V1N -1BNR
(Sensor connector terminal block) OUTPUT CJ-HPHP20-V1N -1APR
CJ-HP20-VP -R (OPEN type cable)
- -
CJ-HP20-VP -L (OPEN type cable)
※It is only for ribbon cable connector (hirose connector) type.
※" " is for cable length. (Basic specification 010 : 1m, 020 : 2m, the others are option)
※For more information, refer to "I/O terminal block & cable catalog".
R-30
GP/LP Common Features
2 RXD+ RXD+
5 (H)
6 3 Non-used Non-used Temp.
4 controller
7 4 Non-used Non-used
3
8 5 SG SG (I)
2 SSR/
9 6 TXD- TXD- Power
1 controller
7 RXD- RXD-
D-Sub 9Pin 8 Non-used Non-used (J)
Female 9 Non-used Non-used Counter
● For power supply, use the wire of which cross section is at least 0.75mm² and
use the wire of which cross section is at least 1.25mm² for grounding. (L)
Panel
● Use crimp-on type terminal with at least 3mm of internal diameter and less than meter
Battery replacement
(O)
Sensor
controller
Please contact out distributor to replace battery.
It may cause an explosion or a fire when improper battery is used. (P)
Switching
mode power
supply
R-31
General Features
RS485
The numerical value Graph of temperature
of temperature
1) GP body Display temperature,
2) PC 2)Temperature controller humidity
3) GP Editor
- Software for drawing GP screen
RS485
4) Manual
- GP editor user manual
- LP, GP Communication manual Easy to set and
#1...........#32
- GP-S044/S057, GP-S070 user manual adjust parameter.
5) Communication cable Effective data control
- Communication cable for PC connection It prints alarm history of controller using printer. It reads the
- Communication cable for controller connection data from barcode reader and save it in PLC.
6) Access devices 1)PLC/Printer
(PLC or controller built in communication ports)
Basic operation flow
Requirements Install GP Editor PLC GP-S044 Printer
for using GP on PC 2)Barcode reader/PLC
Download display
Communication between heterogeneous
GP connect device controllers
data to GP
<Refer to GP, LP
communication manual>
R-2
General Features
realizes cost down, wire reduction, space saving and Download logic data to LP body
(I)
enhanced user friendliness. The logic panel perfectly SSR/
Power
supports serial communication and editing display with GP controller
Test
1) LP body ※RUN/STOP switch holds RUN position.
(M)
Tacho/
2) PC Speed/ Pulse
meter
3) Software
① GP Editor (N)
Display
- Software for drawing LP screen Debugging or editing program unit
② SmartStudio
(O)
- Software for logic program Sensor
controller
4) Manual
- GP Editor user manual Control or start monitoring (P)
- GP,LP Communication manual Switching
mode power
- SmartStudio user manual supply
※Refer to the manual for details on website(www.autonics.
- SmartStudio programming manual (Q)
com) resources. Stepper
- LP-S044, LP-S070 user manual motor&
Driver&Controller
- LP series command manual
5) Communication cable (R)
Graphic/
- Communication cable for PC connection Logic
panel
- Communication cable for controller connection
(S)
6) Access device Field
network
(PLC or controller built in communication ports) device
(T)
Production
stoppage models
& replacement
(U)
Other
R-3
General Features
GP Editor SmartStudio
PC
Drawing data Control program
GP Editor SmartStudio
Drawing data Logic program Download/ Input device Output device
upload data Button Solenoid
Download/ Input device Output device Limit switch Lamp
upload data Button Solenoid Sensors Motor
Limit switch Lamp Other input Other output
A Controls Run Stop devices devices
Sensors Motor
(PLC type)
Other input Other output
Run Stop devices devices
B Controls
(Temperature controller, etc)
Serial printer
R-4
General Features
and menus.
LP manual (E)
Pressure
sensor
● SmartStudio manual
● This drawing software is for GP/LP series. This section describes how to install and use (F)
● GP Editor is the software that allows creating a screen SmartStudio. Rotary
encoder
and designs a tag layout, and then transfer the data ● Programming manual
from screen to GP/LP. After download, GP/LP starts The manual has command and instruction. (G)
monitoring according to your screen data. ● LP-S044, LP-S070 user manual
Connector/
Socket
The manual describes installation and system organization
SmartStudio(Logic program)
and menus. (H)
Temp.
● LP Series instruction manual controller
● Support multi-project Do not use or store it in a place with shock or vibration. (M)
: It is possible to open maximum 5 projects at a same The ground wire of GP/LP should be grounded separately. Tacho/
Speed/ Pulse
time. The ground resistance should be max. 100Ω, please use the meter
R-5
General Features
R-6
General Features
E5ER Modbus ○ ○ ○
(I)
Private communication ○ ○ ○ SSR/
Power
MT Series Modbus ○ ○ × controller
Modbus(TYPE A) ○ ○ ○
(J)
MP Series Private communication ○ ○ ○ Counter
Modbus ○ ○ ×
THD Series
Modbus(TYPE A) ○ ○ ○ (K)
Timer
TZ Series Private communication ○ ○ ○
Modbus ○ ○ ×
TK Series (L)
AUTONICS Modbus(TYPE A) ○ ○ ○ Panel
meter
Modbus ○ ○ ×
TM Series
Modbus(TYPE A) ○ ○ ○ (M)
Tacho/
Modbus ○ ○ × Speed/ Pulse
CT Series meter
Modbus(TYPE A) ○ ○ ○
DS/DA Series Modbus(TYPE A) ○ ○ ○ (N)
Display
ARM Series Modbus(TYPE A) ○ ○ ○ unit
LP-S044, ○ ○ ○
CPU (O)
LP-S070 ○ ○ ○ Sensor
controller
Modbus ○ ○ ×
DPU Series
Modbus(TYPE A) ○ ○ ○ (P)
KONICS Switching
Modbus ○ ○ × mode power
KRN50 supply
Modbus(TYPE A) ○ ○ ○
(Q)
Modbus ○ ○ × Stepper
DELTA DTB Series motor&
Modbus(TYPE A) ○ ○ ○ Driver&Controller
Modbus × × × (R)
DANFOSS FC Series Graphic/
Modbus(TYPE A) ○ ○ ○ Logic
panel
UNIVERSAL UNIVERSAL Modbus(Slave) ○ ○ ○
(S)
MODBUS MASTER MODBUS MASTER Modbus(Master) ○ ○ ○ Field
network
※GP/LP connectable device list will keep updated according to the upgrade of GP Editor or additional patch. It is recommended to device
R-7