Documente Academic
Documente Profesional
Documente Cultură
6. Direcciones IP
Correcto
Puntuación: 4 / 4
Indica a que dirección IP corresponde este número binário:
11000110.11100100.01000001.10010010
Respuesta
La dirección IP es:
198|198. 228|228. 65|65. 146|146
7. Subneting
Correcto
Puntuación: 4 / 4
Indica con las letras S o N si estas direcciones están haciendo subneting.
Respuesta
1. Consola General
Correcto
Puntuación: 3 / 3
Observar la siguiente cabecera de acceso a un equipo
Teldat (c)2001-2013
2. Salvar configuración
Correcto
Puntuación: 2 / 2
Se desea salvar la configuración con un el nombre teldat.
Indicar como se debe realizar
Respuesta
Rellenar los espacios en blanco:
*p 4
Config> save yes teldat|save yes teldat
Building configuration as text... OK
Writing configuration... OK on Flash (not saved in SmartCard) as TELDAT|TELDAT
4. Listar ficheros
Correcto
Puntuación: 5 / 5
Para mostrar los ficheros usaremos el comando:
Respuesta
5. Configurar un usuario
Correcto
Puntuación: 1 / 1
Configurar un usuario con el nombre de nuevo y su password con el mismo nombre:
Respuesta
6. Configurar un hostname
Correcto
Puntuación: 1 / 1
Configurar un el hostname del equipo con el nombre PRUEBA:
Respuesta
7. Ver configuración
Correcto
Puntuación: 1 / 1
Ver toda la configuración sin usar el comando show all, para ello usaremos el comando:
Respuesta
;
dump-command-errors
end
8. Deshabilitar un interfaz
Correcto
Puntuación: 1 / 1
Para deshabilitar un interfaz usaremos el comando:
Respuesta
+ configuration|configuration
Teldat's Router, ATLAS150 7 20 S/N: 106/14437
P.C.B.=8e Mask=0c10 Microcode=00e1 CLK=262144 KHz BUSCLK=65536 KHz PCICLK=32768
KHz
ID: AT150-16F128R L7.20
Boot ROM release:
BIOS CODE VERSION: 05.01 May 28 2013 10:59:46
gzip May 28 2013 10:52:26
io1 May 28 2013 10:59:41
io2 May 28 2013 10:59:
START FROM FLASH L0
Watchdog timer Enabled
Software release: 10.08.40 Oct 17 2013 13:29:04
Compiled by integrator on orion.id.teldat.com
Loaded from primary partition
Hostname: Active user: prueba
Date: Saturday, 01/31/15 Time: 02:58:09
Router uptime: 1m5s
Num Name Protocol
0 IP DOD-IP
3 ARP Address Resolution Protocol
6 DHCP Dynamic Host Configuration Protocol
11 SNMP SNMP
12 OSPF Open SPF-Based Routing Protocol
13 RIP Route Information Protocol
28 PPPoE Point-to-point Protocol Over Ethernet
30 dot1X Extensible Authentication Protocol Over LAN
31 Preauth WLAN Preauthentication
33 BFD Bidirectional Forwarding Detection
35 EOAM Ethernet OAM
40 PIM Protocol Independent Multicast
42 MSDP Multicast Source Discovery Protocol
3 interfaces:
Connector Interface MAC/Data-Link Status
GE0/FE0/LAN1 ethernet0/0 Ethernet/IEEE 802.3 Up
GE1/FE1/LAN2 ethernet0/1 Ethernet/IEEE 802.3 Testing
--- x25-node internal Up
SNMP OperStatus:
Interface OperStatus
ethernet0/0 Up
ethernet0/1 Down
x25-node Up
Encryption Engines:
Hardware: SEC-8272 Revision: 0xA, block 0x0
Cellular Driver Version: 00.09
+ memory|memory
POOL1 Sz:1204000 AllocPart:16 AvlPart:3366
HEAP
bytes total 12214272
chunks used 48669
chunks free 357
bytes free 16080
Total mem: 134217728 Total free mem: 75373795
Available cache mem: 75370496 Available non-cache mem: 75373795
Used cache mem: 12214272 Used non-cache mem: 18645789
Caches: ON Write Back
Flash Memory: 16777216
Free global Buffers:9664 (9663)
Spurious INT 47: 0
+ buffer|buffer
Input Buffers Buffer Sizes
Interface Req Alloc Low Curr Hdr Wrap Data Trail Total
ethernet0/0 40 40 5 40 22 72 1500 4 1598
ethernet0/1 40 40 5 40 22 72 1500 4 1598
x25-node 0 0 0 100 20 72 1500 0 1592
+ device|device ethernet0/0
Auto-test Auto-test Maintenance
Interface CSR Vect valids failures failures
ethernet0/0 FF011300 40 1 0 0
Physical address: 00A02645C008
PROM address: 00A02645C008
Speed: 100 Mbps
Input statistics:
failed, frame too long 0 failed, FCS error 0
failed, alignment error 0 failed, FIFO overrun 0
internal MAC rcv error 0 packets missed 0
Output statistics:
deferred transmission 0 single collision 0
multiple collisions 0 total collisions 0
failed, excess collisions 0 failed, FIFO underrun 0
failed, carrier sense err 0 SQE test error 0
late collision 0 internal MAC trans errors 0
Ethernet MAC code release 1
Comprobaremos el valor Auto-test valids|Auto-test valids que nos mostrará las veces que ha pasado a
un estado UP
Comprobaremos el valor Maintenance failures|Maintenance failures que nos mostrará las veces que
ha pasado a un estado down
1. Habilitar trazas
Correcto
Puntuación: 1 / 1
Queremos habilitar las todas trazas Ethernet del router, para ello usaremos el comando:
Respuesta
+event
-- ELS Monitor --
ELS+ enable trace subsystem eth all|enable trace subsystem eth all
*p 2
01/31/15 03:36:55 ETH.045 Eth self-test Operational test fld 0000 ifc ethernet0/1
01/31/15 03:36:58 ETH.045 Eth self-test Operational test fld 0000 ifc ethernet0/1
2. Crear un filtro
Correcto
Puntuación: 2 / 2
Sobre las trazas anteriores, queremos que el router nos muestre de color rojo las trazas que contengan la
palabra Eth. Para ello usaremos los comandos:
Respuesta
ELS+ filter add 1 "Eth" -1 action red|filter add 1 "Eth" -1 action red
ELS+ enable filter|enable filter