Documente Academic
Documente Profesional
Documente Cultură
SIBs carry relevant information for the UE, which helps UE to access a cell, perform cell re-selection,
information related to INTRA-frequency, INTER-frequency and INTER-RAT cell selections.
4. Minimum of how many SIBs are required for the UE to initiate Attach procedure?
In LTE, for a UE to access the eNB, at the most minimum 2 SIBs are required (SIB1 and SIB2).
Information regarding SIB2-SIB13 are carried in SI messages and are included in schedulingInfoList
which is part of SIB1.
Scheduling of SIBs:
SIB1 uses a fixed schedule with a periodicity of 80 ms and repetitions made within 80 ms.
The first transmission of SIB1 is scheduled in subframe #5 of radio frames for which the SFN mod 8 = 0,
and
Repetitions are scheduled in subframe #5 of all other radio frames for which SFN mod 2 = 0.
Scheduling of other SIB's i.e. SIB-2 to SIB-9 is defined by si-Periodicity and si-WindowLength. Both
these IEs are explained below. For the rest of the SIBs, Paging is received by UE in RRC_IDLE or
RRC_CONNECTED mode for notification of an in-coming SI message.
schedulingInfoList informs the UE regarding the presence of SIB type; other than SIB1. It carriers two
more parameters:
i. si_Periodicity
ii. sib_MappingInfo
si_Periodicity tells about the period in terms of radio frames which helps the UE to read the required
SIB. The value of this parameter is used for calculating the Radio frame where SI will be received.
Sensitivity: Open
si-WindowLength specifies that a SIB should be transmitted somewhere within the specified window
length. Value is in ms. This window starts at the starting sub-frame of the mentioned si_periodicity. SIBs
can be received in any of the sub-frame as mentioned in the WindowLength.
SIB1 in LTE
The first SIB: SIB1
SIB1 contents assist the UE when it is evaluating cell access and also defines the scheduling of other
system information.
RLC-Mode: TM
Direction: E-UTRAN to UE
mcc[0]
mcc[1]
mcc[2]
mnc[0]
mnc[1]
cellReservedForOperatorUse
trackingAreaCode
cellIdentity
cellBarred
intraFreqReselection
cellSelectionInfo
q_RxLevMin
q_RxLevMinOffset
Sensitivity: Open
p_Max
freqBandIndicator
schedulingInfoList[0]
si_Periodicity
sib_MappingInfo[0]
si_WindowLength
systemInfoValueTag
Field Descriptions:
PLMN-Identity Consists of MCC and MNC. The first listed one is the Primary PLMN
Value applicable for the cell. If absent the UE applies the maximum
power according to the UE capability. If eNB configures the value more
p-Max than the value supported by the UE then UE will set the max value
aupported by the UE capability. Example UE Catagory 3 supports max
23 db
Sensitivity: Open
schedulingInfoList information regarding the presence of SIB type; other than SIB1
carries the List of the SIBs mapped. SIB2 is always present in the first
sib_MappingInfo
element of schedulingInfoList
Common for all SIBs other than MIB, SIB1, SIB10, SIB11 and SIB12.
It carries Common and shared channel configuration, RACH related configuration, Timers, UL
Power controls.
SIB2 is not specifically included in the scheduling information in SIB1 but it is always mapped to
the SI message that corresponds to the first entry in the list of SI messages in schedulingInfoList in SIB1
Sensitivity: Open
preambleTransMax
ra_ResponseWindowSize
mac_ContentionResolutionTimer
maxHARQ_Msg3Tx 4
bcch_Config
pcch_Config
prach_Config
pdsch_ConfigCommon
pusch_ConfigCommon
pucch_ConfigCommon
soundingRS_UL_ConfigCommon
uplinkPowerControlCommon
ue_TimersAndConstants
freqInfo
timeAlignmentTimerCommon
Field Descriptions:
ac-BarringInfo Access Class Barring configuration
used to specify common radio resource configurations
radioResourceConfig in the system information and in the mobility control
information
numberOfRA_Preambles Number of non-dedicated random access preambles
Provides the configuration for preamble grouping. If
the field is not signalled, the size of the random access
preamblesGroupAConfig_exist
preambles group A is equal to numberOfRA-
Preambles
powerRampingParameters
powerRampingStep Power ramping factor
preambleInitialReceivedTargetPow
Initial preamble power
er
ra_SupervisionInfo
preambleTransMax Maximum number of preamble transmission
Duration of the RA response window. Value in
ra_ResponseWindowSize
subframes. Value sf2 corresponds to 2 subframes
Timer for contention resolution. Value in subframes.
mac_ContentionResolutionTimer
Value sf8 corresponds to 8 subframes
Maximum number of Msg3 HARQ transmissions,
maxHARQ_Msg3Tx 4
used for contention based random access
bcch_Config
Actual modification period, expressed in number of
radio
modificationPeriodCoeff
frames= modificationPeriodCoeff * defaultPagingCycl
e. n2 corresponds to value 2
pcch_Config
Default paging cycle, used to derive ‘T’. Value rf32
defaultPagingCycle
corresponds to 32 radio frames
Sensitivity: Open
is used as one of parameters to derive the Paging
nB
Frame and Paging Occasion
used to specify the PRACH configuration in the
prach_Config system information and in the mobility control
information
rootSequenceIndex
mentions the:
Preamble format: 0-4 (For frame structure 1 preamble
format is 0-3 and for frame structure 2 it is 0-4)
SFN: whether it will be EVEN no. frmae OR any
prach_ConfigIndex
frame
subframe number: carrier the subframe no. within the
SFN
(Look for the table in TS36.211 - Table 5.7.1-2)
TRUE corresponds to Restricted set and FALSE to
highSpeedFlag
Unrestricted set
zeroCorrelationZoneConfig used for Preamble generation
used to specify the common and the UE specific
pdsch_Config
PDSCH configuration
used to specify the common PUSCH configuration and
pusch_Config the reference signal configuration for PUSCH and
PUCCH
used to specify the common and the UE specific
pucch_Config
PUCCH configuration
soundingRS_UL_Config used to specify the uplink Sounding RS configuration
used to specify parameters for uplink power control in
uplinkPowerControl
the system information and in the dedicated signalling
ue_TimersAndConstants Timer values
freqInfo UL carrier frequency and bandwidth
used to control how long the UE is considered uplink
timeAlignmentTimerCommon
time aligned. Value in subframes
Sensitivity: Open
cellReselectionInfoCommon q_Hyst
speedStateReselectionPars_exist
cellReselectionServingFreqInfo s_NonIntraSearch
threshServingLow
cellReselectionPriority
intraFreqCellReselectionInfo q_RxLevMin
s_IntraSearch
presenceAntennaPort1
neighCellConfig
p_Max
Field Descriptions:
cellReselectionInfoCommon Cell re-selection information common for cells
This specifies the hysteresis value for cell re-selection ranking
q_Hyst criteria. The specified value is added to the serving cell RSRP
measurement.
Sensitivity: Open
# If the field s-IntraSearchP is present, the UE applies the value of
s-IntraSearchP instead. Otherwise if neither 09s-IntraSearch nor s-
IntraSearchP is present, the UE applies the (default) value of
infinity for SIntraSearchP.
is used to09 indicate whether all the neighbouring cells use
09Antenna Port 1. When set to TRUE, the UE may assume that at
presenceAntennaPort1
least two cell-specific antenna ports are used in all neighbouring
cells.
used to provide the information related to MBSFN and TDD UL/DL
neighCellConfig
configuration of neighbour cells.
Field Descriptions:
intraFreqNeighCellList List of intra-frequency neighbouring cells with specific cell
[1-16 instances] re-selection parameters
IntraFreqNeighCellInf
o
physCellId Physical CellID of the neighbour cell
specifies the offset between the two cells. Value -24 -
q-OffsetCell
+24dB
intraFreqBlackCellList List of blacklisted intra-frequency neighbouring cells. These
[1-16 instances] type of cells are not considered for cell re-selection
Sensitivity: Open
Set of physical cell identities reserved for CSG cells on the
frequency on which this field was received. The received
csg-PhysCellIdRange applies if less than 24 hours has
csg_PhysCellIdRange
elapsed since it was received and it was received in the same
primary PLMN. This field is Optional (mandatory for CSG
cell)
10.What SIB does?
t-ReselectionEUTRA defines the time to trigger for cell reselection. Value 0 to 7 sec.
Sensitivity: Open
defined in terms of Resouce blocks associated with a specific
allowedMeasBandwidth
channel bandwidth
cellReselectionPriority defines the Abolute priority of the frequency layer
neighCellConfig information regarding the neighbouring cells
defines the RSRP measurement offset, applied to all cells on the
q-OffsetFreq
specified RF carrier
interFreqBlackCellList the mentioned cells are no considered for cell reselection
11.What SIB6 does?
carrierFreqListUTRA_FDD/TDD
carrierFreq
cellReselectionPriority
threshX_High
threshX_Low
q_RxLevMin
p_Max
q_QualMin
t_ReselectionUTRA
t_ReselectionUTRA_SF
SF_Medium
SF_High
Field Descriptions:
Information specified for up to 16 instances of RF carriers for FDD or
carrierFreqListUTRA_FDD/TDD
TDD
carrierFreq carrier frequency helps the UE to seach
defines the absolute priority of the UMTS. Value 0-7, 0 is the lowest
cellReselectionPriority
priority
Sensitivity: Open
minimum RSCP requirement for candiate UMTS cell. Value -60 to -13
q_RxLevMin
dB. Actual value= Signaled value * 2 +1
Important contents of SystemInformationBlockType7
Sensitivity: Open
# Threshold (in dB) used by UE for cell re-selection to a LOWER priority
frequency
# Cell re-selection is allowed only when Srxlev of the candiate cell is
threshX_Low
greater then threshX_Low and RSRP of serving cell is less than the value
of ThreshServingLow singalled within SIB3
# Value 0 to 31 dB. Actual value= Signaled value * 2
Field Descriptions:
Identifies the source and type of ETWS notification (earthquake,
messageIdentifier
tsunami warning, any emergency or test message)
Sensitivity: Open
Identifies variations of an ETWS notification.
-uses various mechanisms to alert the user (display message, play a
serialNumber tone or vibrate, location where the message is applicable, also
contains an update number which specifies whether a change is in the
message content or not)
Field Descriptions:
Identifies the source and type of ETWS notification
messageIdentifier (earthquake, tsunami warning, any emergency or test
message)
Sensitivity: Open
# allows oedering of the message segments
# Segment number of the ETWS warning message
warningMessageSegmentNumber segment contained in the SIB. A segment number of
zero corresponds to the first segment, one
corresponds to the second segment, and so on
Field Descriptions:
messageIdentifier Identifies the source and type of CMAS notification
serialNumber Identifies variations of a CMAS notification
Indicates whether the included CMAS warning
warningMessageSegmentType
message segment is the last segment or not
Sensitivity: Open
SIB13: MBMS control information
contains the information required to acquire the MBMS control information associated with one or
more MBSFN areas
introduced in Release9
Signalling radio bearer: N/A
RLC-Mode: TM
Logical channel: BCCH
Direction: E-UTRAN to UE
Sensitivity: Open