Documente Academic
Documente Profesional
Documente Cultură
Drill hole
Upper ring
Raceway
Grease Inner ring
nipple
Ball
Ball
The ball bearing turntables and slewing rings allow the bogie
to turn relative to the trailer frame. They transfer both the
axial force and the thrust and tensile forces that occur during
a journey.
Direction of travel
Chassis A frame
Chassis
Upper ring
A frame
8
Ball bearing turntables and slewing rings
Maintenance
Grease nipple
Rubber
washer
Standard Low-maintenance
JOST standard ball bearing turntables are supplied with a thin The low-maintenance versions of ball bearing turntables and
base coating of lubricant. Before it is used for the first time slewing rings mean they do not have to be maintained for up
the ball bearing turntable must be lubricated thoroughly. See to three years or 300,000 km. After this period they must be
JOST installation and operating instructions. serviced in the same way as standard turntables. The low-
maintenance models are distinguished by a green type plate
Connection to the central vehicle lubrication system is and by the letter “W” at the end of the item number. Mainte-
possible (grease is essential, rather than oil). nance conditions differ when fitted to steered semi-trailers or
in the case of heavy conditions of use.
Axial load
KDL 900
KLK HE
KLK SO
KLK ND
KLK N
KLK L
axial load kN
= Standard
= Low-maintenance
The range of applications for ball bearing turntables and All load data for series KDL, HE, SO, ND, L and N apply to
slewing rings depends on the maximum axle load. JOST ball use on roads in fifth wheel steering systems and for paved
bearing turntables and slewing rings cover an axle load range standard road conditions in Central Europe.
from 7.5 to 250 kN.
If the ball bearing turntable and slewing ring are to be
The specified axle loads for series KDL, HE, SO and ND mounted above the steered axle and above the king pin on
relate to use where the slewing ring is mounted on the front semi-trailers, please ask JOST for the load data, giving details
axle of a trailer with three axles and fifth wheel steering, tra- of the vehicle. Any deviations are given on the specification
velling at speeds of up to 100 kph (65 mph). On dual-axle trai- sheet.
lers, the specified axle loads can be exceeded by 10% or
20% at speeds below 30 kph (18 mph).
9
Ball bearing turntables and slewing rings
G
Lower ring
ød ød
45° 20°
H
H
ød ød
G
G
45 °
32 °
øC øC
øE øE
øA øA
32 ° ø 18
KLK HE KLK SO ø 18
Standard Standard
øB øB
øF øF
øD øD
Drill template 2 Direction of travel
G
40° 20°
ød ød
G
G
øC øC
40°
20°
øE øE
øA øA
KLK HE KLK SO 34° ø 16
ø 16
Low-maintenance Low-maintenance
= Shaped profile
Explanations:
WA / Maintenance
10
Ball bearing turntables and slewing rings
Slewing ring
KDL 900
Technical Specification Included in supply
• Low-maintenance
ca. ø H
• Undrilled
øB
øF • Hardened bearings
øD • Primed
12
56
12
ca. ø G
øC
øE
øA
= Shaped profile
11
Ball bearing turntables and slewing rings
8
H
øC
øE
øA
ø 15
10
øC
230
øE
øA
12
Ball bearing turntables and slewing rings
General information
Terms of guarantee
13