Documente Academic
Documente Profesional
Documente Cultură
NO.558 YANLING DONG ROAD, CHANGZHOU CITY, JIANGSU PROVICE, P.R. CHINA
TEL: 0086-519-88803811 FAX: 0086-519-88823959
1 Scope
This specification identifies the requirements of size 、 dimension 、 weight 、 technical
requirements、inspections、tests、packing、marking and test documentation of perforating tube.
This specification is suitable for manufacturing hot rolling SEAMLESS STEEL TUBING FOR
PERFORATING GUN CARRIERS used in oil and gas wells.
2 Applicable Documents
The applicable documents as follows will be suitable for latest edition.
ASTM A751 Standard test methods, practices and terminology for chemical analysis of steel
products.
ASTM A519 Seamless carbon alloy steel mechanical tubing.
ASTM A370 Methods and definitions for mechanical testing of steel.
ASTM E23 Standard test methods for notched bar impact testing of metallic materials.
ASTM E213 Standard practice for ultrasonic examination of metal pipe and tubing.
ASTM E309 Standard practice for eddy-current examination of steel tubular products using
magnetic saturation.
ASTM E18 Standard test methods for Rockwell hardness and Rockwell superficial
hardness of metallic materials.
-1- No distribution without permission from JIANGSU CHANGBAO STEEL TUBE LIMITED CO.
JIANGSU CHANGBAO STEEL TUBE LIMITED CO.
NO.558 YANLING DONG ROAD, CHANGZHOU CITY, JIANGSU PROVICE, P.R. CHINA
TEL: 0086-519-88803811 FAX: 0086-519-88823959
4 Technical Requirements
4.1 Type of Steel and Chemical composition (heat analysis) shall be according to Table 2.
4.2 After heat treatment, mechanical properties shall be according to Table 3.
4.3 Pipes shall be inspected each by each by ET,UT and MT,ET shall be made according to
ASTM E309 level B,UT shall be made on level L2 and notch depth shall be 5% of nominal WT.
4.4 Surface quality.
Internal and external surface shall be free from laps, cracks, seams and other defects greater
than 5% of WT. These defects shall be fully clean up and actual WT shall be equal or exceed the
minimum WT.
Slight heaved or hollow slivering made from production is acceptable, but the OD and WT
shall conform to the specified tolerance and won’t affect use of pipes.
Table 1
OD inches WT inches
2.375 0.197
2.697 0.217
2.697 0.248
2.750 0.312
2.875 0.217
2.875 0.236
2.875 0.308
2.875 0.362
2.875 0.375
3.122 0.313
3.268 0.354
3.374 0.375
3.500 0.254
3.500 0.280
3.500 0.315
3.500 0.346
- 2 - No distribution without permission from JIANGSU CHANGBAO STEEL TUBE LIMITED CO.
JIANGSU CHANGBAO STEEL TUBE LIMITED CO.
NO.558 YANLING DONG ROAD, CHANGZHOU CITY, JIANGSU PROVICE, P.R. CHINA
TEL: 0086-519-88803811 FAX: 0086-519-88823959
3.500 0.362
3.500 0.394
3.500 0.428
3.750 0.313
3.780 0.394
4.000 0.276
4.000 0.354
4.000 0.374
4.000 0.394
4.252 0.315
4.500 0.374
4.500 0.394
4.500 0.438
4.625 0.375
4.625 0.430
4.625 0.438
4.875 0.438
5.000 0.362
5.000 0.375
5.000 0.500
5.125 0.430
5.250 0.430
5.875 0.438
6.000 0.500
7.000 0.500
Table 2
Type of Chemical composition %
Steel C Si Mn P S Cr Mo Ni Ca Cu
4130 0.27~0.32 0.17~0.37 0.5~0.7 ≤0.015 ≤0.008 0.90~1.20 0.15~0.25 ≤0.3 ≤0.20
4130-B 0.27~0.32 0.17~0.37 0.5~0.8 ≤0.015 ≤0.008 1.0~1.20 0.25~0.40 ≤0.3 0.0008-0.003
Table 3
-3- No distribution without permission from JIANGSU CHANGBAO STEEL TUBE LIMITED CO.
JIANGSU CHANGBAO STEEL TUBE LIMITED CO.
NO.558 YANLING DONG ROAD, CHANGZHOU CITY, JIANGSU PROVICE, P.R. CHINA
TEL: 0086-519-88803811 FAX: 0086-519-88823959
Yield
Grade strength Tensile Charpy V-Notch test a, b Akv ,J
RP0.2,KSI strength
Rm, Elongation Shear Hardness
KSI A,% transverse longitudinal percentage HRC
b When full size specimen isn’t available, the sub-size specimen with width that 7.5mm or
5.0mm shall be acceptable. The minimum CVN absorbed energy requirement for sub-size test
specimens shall be that specified for a full-size test specimen multiplied by the reduction factor
0.80 and 0.55.
5 Inspection
5.1 Pipes shall be measured each by each with available measurement.
5.2 Internal and external surface shall be visually inspected with light.
5.3 Inspection Item、Inspection Methods、Specimen Taken shall be according to Table 4.
Table 4
-4- No distribution without permission from JIANGSU CHANGBAO STEEL TUBE LIMITED CO.
JIANGSU CHANGBAO STEEL TUBE LIMITED CO.
NO.558 YANLING DONG ROAD, CHANGZHOU CITY, JIANGSU PROVICE, P.R. CHINA
TEL: 0086-519-88803811 FAX: 0086-519-88823959
Packing, Marking and Mill Test Certificate of pipes shall be according to API 5CT and EN
10204 3.1 ISO 10474 3.1B.
-5- No distribution without permission from JIANGSU CHANGBAO STEEL TUBE LIMITED CO.