Documente Academic
Documente Profesional
Documente Cultură
Manual
Overall Appearance
I. Purpose
This manual will mainly introduce the disassembly method for R829 (13075) to you
so as to serve as a guide for the production line in the factory and after-sale
maintenance, in order to avoid some unecessary damages.
Exploded Diagram
Fig. 3.1.1
IV. Disassembling procedure
1. Preparation
(1) Before conducting disassembly, this product shall be forced to shut down
instead of resorting to shutdown option in the system so as to completely cut off
the power supply and protect electronic components to the most.
(2) A forced shutdown is conducted through engineering order *#911# or pressing
the Power Key for about 8 seconds until the display screen has closed down.
2. Disassemble the battery cover
(1) Before disassembling the battery cover, please use the heat-gun to warm up the
whole battery cover for 1-2min, and suck the lower part of the battery cover to pull
out the battery cover by using the Sucker. After disassembling the battery cover,
please clear up the adhesive residue in the battery cover and the bottom cover. See
Fig. 4.2.1.
Fig. 4.2.1
3. Disassemble the Card Holder
(1) Put this smart phone downward, insert the pin or fine pin into the lower right
corner, push to eject the SIM card holder and then detach the SIM Card from the
Card Holder, as shown in Fig. 4.3.1.
Fig. 4.3.1
4. Disassemble the Bottom Cover
(1) Tear down the Graphite sheet with tweezers or Fingernail, as shown in Fig. 4.4.1.
Fig. 4.4.1
(2) Remove the 12 screws from the bottom cover of the fixed main board, and
classify these screws according to their category----CM1.4×3(6pcs),
CM1.4×2.3(4pcs), and CM1.2×2(2pcs), as shown in Fig. 4.4.2.
Fig. 4.4.2
(3) Unclench the snap from the top right corner of the bottom cover with the
Disassembling rod and finally unlock the snap at the SIM card holder (pay attention to
the risk of distortion and damage). When the snap has been thoroughly unlocked,
please remove the bottom cover and clear up the adhesive residue in the bottom cover
and top cover as shown in Fig. 4.4.3.
Unclench this
snap in the end
Fig. 4.4.3
add two
drops of
alcohol along
the left and
right sides
Fig. 4.5.1
(2) Loosen the two screws (CM1.2x2) at the fixed main board; then tear down the
high-temperature tape on the FPC Key with tweezers, take out the FPC Key from the
hole of the Key bracket and finally open the BTB button of the touch screen as shown
Fig. 4.6.2.
Fig. 4.6.2
(3) Open the RF connecting cable main board with tweezers in the shown method
and please try not to pull the RF cable directly with your hand (the risk of loosening
and breakage of the RF cable). See Fig. 4.6.3.
Fig. 4.6.3
(4) Lift up the main board from the top right corner, open the display screen BTB and
the main FPC-BTB, and remove the main board as shown in Fig 4.6.2.
Fig 4.6.2
7. Disassemble the antenna plate
(1) Pull out the sound device bracket according to the position and orientation as
shown in Fig. 4.7.1.
Fig. 4.7.1
(2) Pull out the FPC-BTB and RF Cable at the small plate with tweezers as shown in
Fig. 4.7.2.
Fig. 4.7.2
(2) Lift up the small plate with tweezers from the lower left corner of the antenna
plate and carefully shake to detach the antenna plate from the main board top cover as
shown in Fig. 4.7.3. Please avoid overexertion and protect the components of the
small plate from sealing off and even shedding. Finally, please try not to break FPC
when you are taking out the USB Port.
Fig. 4.7.3
Main FPC
Power Key
Volume Key
Loudspeaker
Motor
RF Cable
Battery
Card
Holder