Documente Academic
Documente Profesional
Documente Cultură
0 Product Specification
Rev.1.2
()Preliminary Specifications
(*
*)Final Specifications
_________________________________ ____________________________________
12
2/
01
Eugene CC Chen
y
nl
O
____________________________________
se
U
____________________________________
L
TC
or
Prepared By PM
lF
ia
Karen HY Hsieh
nt
e
____________________________________
fid
on
C
O
AU
Contents
No
CONTENTS
RECORD OF REVISIONS
1 GENERAL DESCRIPTION
3 ELECTRICAL SPECIFICATION
4 OPTICAL SPECIFICATION
5 MECHANICAL CHARACTERISTICS
0
6 PACKING
/2
12
7 PRECAUTION
O
se
7-5 STORAGE
or
Record of Revision
Version Date Page Description
0.0 2012/08/08 First release
0.1 2012/08/16 16 Modify center transmittance
2012/08/16 20 Update 2D drawing
10 Update Interface Connections
0.2 2012/09/10 12 Update timing table
16 Update Color Chromaticity
10 Update Interface Connections
1.0 2012/09/20 15 Update Power Sequence
23 Update box carrying for SKD
16 Update Surface Luminance
1.1 2012/10/01
20 Update 2D drawing
1.2 2012/12/01 16 Update Center Transmittance
2012/12/17 16 Update Color Chromaticity
0
/2
12
2/
01
/2
y
nl
O
se
U
al
rn
te
In
L
TC
or
lF
ia
e nt
id
f
on
C
O
AU
1. General Description
This specification applies to the 42.02 inch Color TFT-LCD SKD model T420HVN04.0. This LCD Open Cell Unit
has a TFT active matrix type liquid crystal panel 1,920x1,080 pixels, and diagonal size of 42.02 inch. This Open
Cell Unit supports 1,920x1,080 mode. Each pixel is divided into Red, Green and Blue sub-pixels or dots which are
arranged in vertical stripes. Gray scale or the brightness of the sub-pixel color is determined with a 8-bit gray scale
signal for each dot.
* General Information
Note 1: LCD display as below illustrated when signal input with “ABC”.
In
L
TC
or
lF
ia
nt
e
f id
on
C
O
AU
3. Electrical Specification
The T420HVN04.0 Open Cell Unit requires power input which is employed to power the LCD electronics and to
drive the TFT array and liquid crystal.
3.1.1: DC Characteristics
Value
Parameter Symbol Unit Note
Min. Typ. Max
LCD
Power Supply Input Voltage VDD 10.8 12 13.2 VDC
Power Supply Input Current IDD -- 1.1 1.3 A 1
Power Consumption PC -- 15.6 Watt 1
Inrush Current IRUSH -- -- 4 A 2
Permissible Ripple of Power Supply Input Voltage VRP -- -- VDD * 5% mVpk-pk 3
Input Differential Voltage ∣VID∣ 200 400 600 mVDC 4
LVDS Differential Input High Threshold Voltage VTH +100 -- +300 mVDC 4
0
Interface
/2
VIH
Input High Threshold Voltage 2.7 -- 3.3 VDC 5
/2
CMOS (High)
y
Interface VIL
nl
(Low)
se
U
al
rn
te
In
L
TC
or
lF
ia
ent
fid
on
C
O
AU
3.1.2: AC Characteristics
Value
Parameter Symbol Unit Note
Min. Typ. Max
Receiver Clock : Spread Spectrum Fclk Fclk
Fclk_ss -- MHz 6
Modulation range -3% +3%
Receiver Clock : Spread Spectrum
LVDS Fss 30 -- 200 KHz 6
Modulation frequency
Interface
Receiver Data Input Margin
Fclk = 85 MHz tRMG -0.4 -- 0.4 ns 7
Fclk = 65 MHz -0.5 -- 0.5
Note :
1. VDD = 12.0V, Fv = 60Hz, Fclk= Max freq., 25 ℃, Test Pattern : White Pattern
>> refer to “Section:3.3 Signal Timing Specification, Typical timing”
2. Measurement condition : Rising time = 400us
VDD
90%
10%
GND
0
/2
400µs
12
2/
3. Test Condition:
01
(1) The measure point of VRP is in LCM side after connecting the System Board and LCM.
/2
4. VICM = 1.25V
O
se
LVD S -
U
V IC M V TH
|V ID |
al
V TL
rn
LVD S +
te
In
L
TC
GND
or
lF
ia
|V ID |
e nt
0V
f id
on
|V ID |
C
O
AU
5. The measure points of VIH and VIL are in LCM side after connecting the System Board and LCM.
6. LVDS Receiver Clock SSCG (Spread spectrum clock generator) is defined as below figures
1/FSS
Fclk_ss(max)
Fclk
Fclk_ss(min)
0
/2
12
2/
01
/2
y
nl
O
se
U
al
rn
te
In
L
TC
or
lF
ia
nt
e
fid
on
C
O
AU
tRIP2
tRIP3
tRIP4
tRIP5
tRIP6
tRIP0
0
/2
tRIP1
12
LVDS-Rx
Rx3 Rx2 Rx1 Rx0 Rx6 Rx5 Rx4 Rx3 Rx2 Rx1 Rx0 Rx6
2/
Input Data
01
/2
LVDS-Rx
Input Clock Vdiff = 0V
y
nl
O
se
1/Fclk=T
U
al
rn
te
In
L
TC
or
lF
ia
nt
e
f id
on
C
O
AU
40 N.C.
not connect)
al
rn
not connect)
In
not connect)
or
not connect)
ia
nt
not connect)
AU
Clock
CHx_0+ R1 R0 G0 R5 R4 R3 R2 R1 R0 G0
CHx_0-
CHx_1+ G2 G1 B1 B0 G5 G4 G3 G2 G1 B1
CHx_1-
CHx_2+
CHx_2- B3 B2 DE NA NA B5 B4 B3 B2 DE
CHx_3+
CHx_3- R7 R6 NA B7 B6 G7 G6 R7 R6 NA
0
/2
12
Note: x = 1, 2, 3, 4…
2/
01
/2
Clock
al
rn
te
In
CHx_0+ R3 R2 G2 R7 R6 R5 R4 R3 R2 G2
CHx_0-
L
TC
or
CHx_1+ G4 G3 B3 B2 G7 G6 G5 G4 G3 B3
lF
CHx_1-
G7
ia
ent
CHx_2+
id
CHx_2- B5 B4 DE NA NA B7 B6 B5 B4 DE
f
on
C
CHx_3+
O
CHx_3- R1 R0 NA B1 B0 G1 G0 R1 R0 NA
AU
Note: x = 1, 2, 3, 4…
Notes:
(1) Display position is specific by the rise of DE signal only.
Horizontal display position is specified by the rising edge of 1st DCLK after the rise of 1st DE, is displayed on the
0
(2)Vertical display position is specified by the rise of DE after a “Low” level period equivalent to eight times of
2/
horizontal period. The 1st data corresponding to one horizontal line after the rise of 1st DE is displayed at the top
01
line of screen.
/2
(3)If a period of DE “High” is less than 1920 DCLK or less than 1080 lines, the rest of the screen displays black.
y
nl
O
(4)The display position does not fit to the screen if a period of DE “High” and the effective data period do not
se
Page 13 / 24
Tv M pixel
Tblk(v) Tdisp(v)
N L ine
Th
DE
0
/2
12
RGB Line Invalid Data Line Line Line Line
2/ Line Invalid Data
Data
N 1 2 3 4 01 N
CH1
Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel
Invalid Data Invalid Data
M-7 M-5 M-3 M-1 1 3 5 7 9 11 M-5 M-3 M-1 1 lF3
ia
nt e
CH2
Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel
Invalid Data Invalid Data id
M-6 M-4 M-2 M 2 4 6 8 10 12 M-4 M-2 M 2 4 f
on
C
O
AU
T420HVN04.0 Product Specification
Rev.1.2
3.3 Color Input Data Reference
The brightness of each primary color (red, green and blue) is based on the 8 bit gray scale data input for the color;
the higher the binary input, the brighter the color. The table below provides a reference for color versus data input.
RED(254) 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
12
2/
RED(255) 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
01
GREEN(000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
/2
GREEN(001) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0
y
nl
G ----
O
se
GREEN(254) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0
U
GREEN(255) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
al
rn
BLUE(000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
te
BLUE(001) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
In
L
B ----
TC
BLUE(254) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0
or
lF
BLUE(255) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
ia
ent
id
f
on
C
O
AU
0
/2
Values
12
Parameter Unit
Min. Type. Max.
2/
01
t1 0.4 --- 30 ms
/2
t2 0.1 --- 50 ms
y
nl
O
*1
t4 0 --- --- ms
U
al
t5 0 --- --- ms
rn
te
*2
t6 --- --- --- ms
In
*3
t8 10 --- 50 ms
or
t9 0 --- --- ms
lF
Note:
f
on
(1) t4=0 : concern for residual pattern before BLU turn off.
C
(2) t6 : voltage of VDD must decay smoothly after power-off. (customer system decide this value)
O
(3) When CMOS Interface signal is N.C. (no connection), opened in Transmitted end, t8 timing spec can be
AU
negligible.
4. Optical Specification
Optical characteristics are determined after the open cell unit and light source has been ‘ON’ and stable for
approximately 45 minutes in a dark environment at 25°C. The values specified are at an approximate distance
50cm from the LCD surface at a viewing angle of φ and θ equal to 0°.
Fig.1 presents additional information concerning the measurement equipment and method.
SR3 or equivalent
Values
Parameter Symbol Condition Unit Notes
Min. Typ. Max
Contrast Ratio CR 2400 3000 -- 1,2
Surface Luminance
0
(White)
12
Color Chromaticity 6
O
Red RX 0.660
se
U
RY 0.324
al
rn
Green GX 0.273
With CS-1000T
te
GY 0.595
In
Blue BX 0.138
TC
BY 0.092
or
White WX 0.297
lF
ia
WY 0.340
ent
Viewing Angle 7
f id
3. Surface luminance is luminance value at point 5 across the LCD surface 50cm from the surface with all pixels
displaying white. For more information see FIG 2. LWH=Lon5 where Lon5 is the luminance with all pixels
displaying white at center 5 location.
FIG. 2 Luminance
H/2 1 2 3
4 5 6 H
7 8
H/6
V/6 V/2
0
/2
12
5. Response time Tγ is the average time required for display transition by switching the input signal for five
/2
Measured Target
O
se
75%
TC
The response time is defined as the following figure and shall be measured by switching the input signal for
ia
nt
Any level of gray (Bright) Any level of gray (Dark) Any level of gray (Bright)
T γ (F) T γ (R)
6. Light source here is the standard light source “C” which is defined by CIE and driving voltages are based on
suitable gamma voltages. The calculating method is as following:
A. Measure the “Module” and “BLU” optical spectrums (W, R, G, B) of AUO standard module.
B. Calculate cell spectrum from “Module” and “BLU” spectrums.
C. Calculate color chromaticity by using cell spectrum and the spectrum of standard light source “C”.
7. Viewing angle is the angle at which the contrast ratio is greater than 10. The angles are determined for the
0
horizontal or x axis and the vertical or y axis with respect to the z axis which is normal to the LCD surface. For
/2
12
5. Mechanical Characteristics
Item Typ Unit Note
Weight 1200 g
0
/2
12
2/
01
/2
y
nl
O
se
U
al
rn
te
In
L
TC
or
lF
ia
ent
fid
on
C
O
AU
6.Packing
Open cell shipping label (35*7mm)
T420HVN04.0
1. S/N Number
2. Grade
3. Manufacture Fab.
4. Manufactured date
5. Model name
Carton Label:
0
/2
12
T420HVN04.0
2/
01
91.42T28.0XX
/2
XXXXX–XXXXX–XXXXX
y
nl
O
se
U
al
rn
te
In
L
TC
or
lF
ia
nt
e
fid
on
C
O
Packing Process:
0
/2
12
Pallet Dimension:1100*800*140 mm
fid
on
8 Boxes/Pallet, after stack 8 boxes, then put EPP top cover on it.
C
O
AU
7. PRECAUTIONS
Please pay attention to the followings when you use this TFT LCD Open Cell unit.
(1) The open cell unit listed in the product specification sheets was designed and manufactured for TV
12
application
2/
01
(2) The spike noise causes the mis-operation of circuits. It should be lower than following voltage:
/2
(3) Response time depends on the temperature. (In lower temperature, it becomes longer.)
O
(4) Brightness/transmittance depends on the temperature. (In lower temperature, it becomes lower.) And in
se
lower temperature, response time (required time that brightness is stable after turned on) becomes longer.
U
al
(5) Be careful for condensation at sudden temperature change. Condensation makes damage to polarizer
rn
te
or electrical contacted parts. And after fading condensation, smear or spot will occur.
In
(6) When fixed patterns are displayed for a long time, remnant image is likely to occur.
L
TC
(7) Module has high frequency circuits. Sufficient suppression to the electromagnetic interference shall be
or
done by system manufacturers. Grounding and shielding methods may be important to minimize the
lF
interface.
ia
nt
Since a open cell unit is composed of electronic circuits, it is not strong to electrostatic discharge. Make
f
on
certain that treatment persons are connected to ground through wrist band etc. And don’t touch interface pin
C
O
directly.
AU
7-5 STORAGE
When storing open cell units as spares for a long time, the following precautions are necessary.
(1) Store them in a dark place. Do not expose the open cell unit to sunlight or fluorescent light. Keep the
temperature between 5℃ and 35℃ at normal humidity.
(2) The polarizer surface should not come in contact with any other object. It is recommended that they be
stored in the container in which they were shipped.
0
/2
12
2/
01
/2
y
nl
O
se
U
al
rn
te
In
L
TC
or
lF
ia
nt
e
fid
on
C
O
AU