Documente Academic
Documente Profesional
Documente Cultură
SUB300
Amplifier/Subwoofer
SERVICE MANUAL
- CONTENTS -
BASIC SPECIFICATIONS……………….….….….….…………….1
DETAILED SPECIFICATIONS ……..…………….……………..2
OPERATION ………….……………………………..…………….4
CONNECTIONS..………………………..………….…….………...5
BASIC TROUBLESHOOTING…..…………….….….…….……...7
TEST SET-UP AND PROCEDURE……………………………….8
EXPLODED VIEW/PARTS LIST…………………………………..9
BLOCK DIAGRAM..…………………………………………….....10
PCB DRAWINGS………………..………………………………...11
120V ELECTRICAL PARTS LIST ………………..……………..13
230V ELECTRICAL PARTS LIST …………………..…………..16
INTEGRATED CIRCUIT/TRANSISTOR PINOUTS.................19
120V SCHEMATICS.………..………………….………. ………20
230V SCHEMATICS.………..…………………….……. ………23
PACKAGING…………………………….………………………...25
BASIC SPECIFICATIONS
SUB300 Subwoofer
Configuration: Floor-firing, bass-reflex ported enclosure
Woofer: 10" (254mm) cone
Occasional refinements may be made to existing products without notice but will always meet or exceed original
specifications unless otherwise stated
1
Downloaded from www.Manualslib.com manuals search engine
SUB300 (SCS300.7sys)
JBL SUB 300 150W Powered Sub/ Plate Amp
QA Test
Parameter Specification Unit Limits Conditions Notes
Amp Section
Type (Class AB, D, other) D D N/A
Load Impedance (speaker) 4 Ohms N/A Nominal
Rated Output Power 150 Watts 140 1 input driven
THD@ Rated Power 0.5 % 1 22KHz filter
THD @ 1 Watt 0.1 % 0.3 22KHz filter
DC Offset 10 mV-DC 50 @ Speaker Outputs
Measured at speaker terminals, Output
Damping factor >100 DF 30 power 140 Watts THD 0.1 %
Input Sensitivity
Input Frequency 50 Hz 50 Nominal Freq. 1 input driven
Line Input (L&R) 250 mVrms ±2dB To rated power 1 input driven
LFE Input 145 mVrms ±2dB To rated power LFE input driven only
Speaker/Hi Level Input 2.5 Vrms ±2dB To rated power (-20 dB below Line In)...1 input driven
Signal to Noise
SNR-A-Weighted 100 dBA 85 rel. to rated power A-Weighting filter
SNR-unweighted 90 dBr 80 rel. to rated power 22KHz filter
SNR @ 1W-unweighted 60 dBr 55 rel. to 1W Output 22KHz filter
Volume @max, using RMS reading
Residual Noise Floor 1 mVrms 2 DMM/VOM (or A/P)
Volume @max, w/ A/P Swept
Bandpass Measurement (Line freq.+
Residual Noise Floor 1 mVrms(max) 2 harmonics)
Input Impedance
Line input L&R , LFE >10 K ohms N/A Nominal
Speaker/Hi Level Input 4.7 K ohms N/A Nominal
Filters
Left & Right Low Pass fixed Hz -- ±2dB
Slope & Q 4th dB/Octave N/A
LFE Low Pass fixed Hz -- ±2dB
Slope & Q 2nd dB/Octave N/A
Subsonic filter (HPF) Hz -- ±2dB
Slope & Q 2nd dB/Octave N/A
Features
LFE Input YES functional BW Limited to 500 Hz
Volume pot Taper (lin/log) log -- functional
ATO YES functional
Input Configuration
Line In (L,R) L ,R -- functional RCA inputs: L , R Summed to Mono
Line level in LFE LFE functional
Spkr/Hi Level In (L,R) L,R -- functional L R Summed to Mono
Spkr Out: Level out (L,R)Hi P L,R functional Direct by pass from Speaker in
2
Downloaded from www.Manualslib.com manuals search engine
SUB300 (SCS300.7sys)
QA Test
Parameter Specification Unit Limits Conditions Notes
Transients/Pops
ATO Transient 5 mV-peak 10 @ Speaker Outputs
Turn-on Transient 50 mV-peak 100 @ Speaker Outputs AC Line cycled from OFF to ON
Turn-off Transient 50 mV-peak 100 @ Speaker Outputs AC Line cycled from ON to OFF
Efficiency
Maximum allowable input power under
nominal Input voltage and frequency,
Stand-by Input Power 14 Watts 15 @ nom. line voltage HOT or COLD operation.
Power Cons.@rated power 250 Watts 260 @ nom. line voltage 150 Watts @ 4 Ohms nominal line voltage
Protection
Short Circuit Protection YES -- functional Direct short at output
Temperature rise should not exceed 35K
Thermal Protection 65 deg. C -- functional @1/8 max unclipped Power rise
DC Offset Protection YES -- functional DC present at Speaker Out leads Relay or crowbar (for driver/fire
Line Fuse Rating
External fuse with UL/SEMKO rated
US Version 2.5 Amps Type-T or Slo Blo holder
External fuse with UL/SEMKO rated
EU Version 1.6 Amps Type-T or Slo Blo holder
3
Downloaded from www.Manualslib.com manuals search engine
SUB300 (SCS300.7sys)
OPERATION
Move the Master Power switch or if the subwoofer will not be
(marked “Power” å) to the “•” used, switch the Master Power
(On) position to use the sub- switch å to the Off position.
woofer. The SUB300 subwoofer
will automatically turn on or go
into standby (sleep) mode
when left in the auto mode
(“Auto/On” switch ç in the ç
“Auto” position). When your
receiver or amplifier is off, or is
not sending program material ∫
to the subwoofer, the sub-
woofer will be in standby mode
(LED will be red). When the
subwoofer senses an audio sig-
nal, it will automatically turn on
(LED will be green). If the sub-
woofer does not sense a signal
after approximately 20 minutes,
it will automatically go into
standby mode.
When the “Auto/On” switch ç å
is switched to the “On” posi-
tion, the subwoofer will remain CAUTION
RISK OF ELECTRIC SHOCK
material is playing.
If you will be away from home
for an extended period of time,
VOLUME
Volume may be adjusted
Subwoofer using the Subwoofer Level
Level control ∫ as shown.
MIN MAX
Subwoofer
Level
MIN MAX
10
4
Downloaded from www.Manualslib.com manuals search engine
SUB300 (SCS300.7sys)
DOLBY* DIGITAL OR DTS®
(OR OTHER DIGITAL SURROUND MODE) CONNECTION
RECEIVER SUBWOOFER Frequency Effects channel. your receiver for 5.1-, 6.1-
Connect this jack to the LFE or 7.1-channel operation as
L
LFE OUT LINE LFE output or subwoofer output appropriate. The front left,
LEVEL on your receiver or amplifier. front right, center and rear
R
IN
Connect each speaker to the speakers should all be set to
corresponding speaker “Small.” If your receiver
Use this installation method terminals on your receiver allows you to set the
for Dolby Digital, DTS or or amplifier. crossover frequency
other digital surround between the subwoofer and
Make sure that you have
processors: the main speakers, select
configured your surround
Use the line-level input jack sound processor for “Sub- 100Hz or the setting that is the
marked “LFE” for the Low- woofer On.” Also configure closest frequency below it.
Use this installation method Use RCA-type interconnects NOTE: If your receiver or
for Dolby Pro Logic applica- to connect the line-level amplifier only has one sub-
tions (not Dolby Digital, DTS subwoofer outputs on your woofer output jack, then you
or other digital processing), receiver or amplifier to the will need to use a Y-connector
where the receiver/proces- line-level inputs on the sub- (not included). Plug the male
sor is equipped with a sub- woofer. IMPORTANT: Do not end of the Y-connector into
woofer output, or a volume- use the LFE input on the sub- your receiver or amplifier’s
controlled preamp (line-) woofer with Dolby Pro Logic subwoofer output jack, and
level output: processors. connect each of the two
female ends to separate
RCA-type interconnects.
Left Front Center Right Front
Finally, plug the RCA-type
– + – + – + interconnects into the line-
level inputs on the sub-
Subwoofer
woofer.
Line-
Level In Connect each speaker to
L the corresponding speaker
R terminals on your receiver
Receiver
or amplifier.
Left Subwoofer Right Make sure your receiver or
Front Out Front
– + – + processor is correctly con-
R L figured to indicate that the
– +
subwoofer is “On.”
Center
Left
Note for advanced users: If
Surround Back Surround Back Right
Surround
– + –
Left
+
Right
– +
Surround your receiver/processor has
– +
a built-in low-pass crossover
filter for the subwoofer out-
Surround Back Surround Back
Left Surround Left Right Right Surround put, you may use the LFE
– + – + – + – + input to bypass the sub-
woofer’s internal crossover.
8
5
Downloaded from www.Manualslib.com manuals search engine
SUB300 (SCS300.7sys)
DOLBY PRO LOGIC (NON-DIGITAL) – SPEAKER LEVEL
– + – + – + – +
9
6
Downloaded from www.Manualslib.com manuals search engine
SUB300 (SCS300.7sys)
TROUBLESHOOTING
If there is no sound from any owner’s manual for that electrical outlet, and is
of the speakers: product for further informa- turned on (Power switch
• Check that receiver/ampli- tion. If the problem has fol- å in the “•” position).
fier is on and a source is lowed the speaker, consult • In Dolby Digital or DTS
playing. your dealer for further assis- modes, make sure your
• Check that the powered tance or, if that is not possi- receiver/processor is config-
subwoofer is plugged in, ble, visit www.jbl.com. ured so that the subwoofer
and its Power switch å is If there is no sound from the and LFE output are enabled.
switched on (“•” position). center speaker: If there is no sound from
• Check all wires and con- • Check all wires and con- the surround speakers:
nections between receiver/ nections between receiver/ • Check all wires and con-
amplifier and speakers. amplifier and speaker. Make nections between receiver/
Make sure all wires are con- sure all wires are connected. amplifier and speakers.
nected. Make sure none of Make sure none of the Make sure all wires are con-
the speaker wires are speaker wires are frayed, nected. Make sure none of
frayed, cut or punctured, or cut or punctured, or touch- the speaker wires are
touching each other. ing each other. frayed, cut or punctured, or
• Review proper operation of • If your receiver/processor touching each other.
your receiver/amplifier. is set in Dolby Pro Logic mode, • Review proper operation of
If there is no sound coming make sure the center speaker your receiver/amplifier and
from one speaker: is not in phantom mode. its surround sound features.
• Check the “Balance” control • If your receiver/processor • Make sure the movie or
on your receiver/amplifier. is set in one of the Dolby TV show you are watching
Digital or DTS modes, make is recorded in a surround
• Check all wires and con-
sure the receiver/processor sound mode. If it is not,
nections between receiver/
is configured so that the check to see whether your
amplifier and speakers.
center speaker is enabled. receiver/amplifier has other
Make sure all wires are con-
nected. Make sure none of If the system plays at low surround modes you may use.
the speaker wires are volumes but shuts off as • In Dolby Digital or DTS
frayed, cut or punctured, or volume is increased: modes, make sure your
touching each other. • Check all wires and con- receiver/processor is config-
• In Dolby Digital or DTS nections between receiver/ ured so that the surround
modes, make sure that the amplifier and speakers. speakers are enabled. When
receiver/processor is config- Make sure all wires are con- five satellites are in use,
ured so that the speaker in nected. Make sure none of remember to configure your
question is enabled. the speaker wires are receiver or processor for
frayed, cut or punctured, or 6.1-channel operation, and
• Turn off all electronics
touching each other. when all six satellites are in
and switch the speaker in
• If more than one pair of use, configure your receiver
question with one of the
main speakers is being used, or processor for 7.1 channels.
other speakers that is work-
ing correctly. Turn every- check the minimum imped- • Review the operation of
thing back on, and deter- ance requirements of your your DVD player and the
mine whether the problem receiver/amplifier. jacket of your DVD to make
has followed the speaker, or If there is low (or no) bass sure that the DVD features
has remained in the same output: the desired Dolby Digital or
channel. If the problem is • Make sure the connections DTS mode, and that you
in the same channel, the to the left and right “Speaker have properly selected that
source of the problem Inputs” have the correct mode using both the DVD
is most likely with your polarity (+ and –). player’s menu and the DVD
receiver or amplifier, and disc’s menu.
• Make sure the subwoofer
you should consult the is plugged into an active
11
7
Downloaded from www.Manualslib.com manuals search engine
SUB300 (SCS300.7sys)
SUB300 TEST PROCEDURE
Equipment needed:
• Function/signal generator/sweep generator
• Integrated Amplifier
• Multimeter
• Speaker cables
1) From the signal generator, Connect both right and left line level inputs (RCA) to signal generator and UUT.
Use Y-cable if necessary from mono source. Do not use the LFE jack.
2) On the front of the unit, turn the LEVEL control full counterclockwise (MIN).
3) Turn on generator, adjust to 100mV, 50 Hz.
4) Plug in UUT; turn the power switch ON. Turn LEVEL control full clockwise (MAX)
5) LED should now be Green; immediate bass response should be heard and felt from port tube opening.
6) Turn off generator, turn LEVEL control fully counterclockwise (MIN), disconnect RCA cable.
7) Connect one pair of speaker cables to one pair Speaker Level input terminals on UUT. Cables should be
connected to an integrated amplifier fed by the signal generator.
8) Turn on generator and adjust so that speaker level input at the amplifier is 2.0V, 50 Hz.
9) Turn LEVEL control full clockwise (MAX)
10) Green LED should light, immediate bass response should be heard and felt from the port tube opening.
Sweep Function
1) Follow steps 7-10 above, using a sweep generator as a signal source.
2) Sweep generator from 20Hz to 1kHz. Listen to the cabinet and drivers for any rattles, clicks, buzzes or any
other noises. If any unusual noises are heard, remove woofer and test.
8
Downloaded from www.Manualslib.com manuals search engine
SUB300 (SCS300.7sys)
SUB300
Exploded View
9
Downloaded from www.Manualslib.com manuals search engine
SUB300 (SCS300.7sys)
10
11
12
Input/Main PCBs
Resistors
Capacitors
13
Downloaded from www.Manualslib.com manuals search engine
SUB300 (SCS300.7sys) 120v Electrical parts List cont'd
Part Number Description Qty Reference Designator
Input/Main PCBs
Semiconductors
Miscellaneous
Power Amp Class D Module part# 012-7500-00022 RECOMMENDED: REPLACE ENTIRE MODULE
Resistors
14
Downloaded from www.Manualslib.com manuals search engine
SUB300 (SCS300.7sys) 120v Electrical parts List cont'd
Part Number Description Qty Reference Designator
Capacitors
Semiconductors
Miscellaneous
MISCELLANEOUS
15
Downloaded from www.Manualslib.com manuals search engine
SUB300 (SCS300.7sys)
Input/Main PCBs
Resistors
Capacitors
16
Downloaded from www.Manualslib.com manuals search engine
SUB300 (SCS300.7sys) 230v Electrical parts List cont'd
Part Number Description Qty Reference Designator
Input/Main PCBs
Semiconductors
Miscellaneous
Resistors
17
Downloaded from www.Manualslib.com manuals search engine
SUB300 (SCS300.7sys) 230v Electrical parts List cont'd
Part Number Description Qty Reference Designator
Capacitors
Semiconductors
Miscellaneous
MISCELLANEOUS
18
Downloaded from www.Manualslib.com manuals search engine
SUB300 (SCS300.7sys)
19
Downloaded from www.Manualslib.com manuals search engine
SUB300 (SCS300.7sys) 120v SCHEMATIC PAGE 1
20
21
22
23
24
SCS300.7
Packaging
Warranty Card
Speaker Wire 20 Feet (3) 405-000-00258
166-020F84XX
Owner’s Manual
Speaker Wire 40 Feet (4) 1 (120V) 406-000-00959
166-040F84XX (230V) 406-000-00958
Hardware Bag A
371-000-05024
Hardware Bag B
371-000-05027 Sub Packing
431-000-05034
Screw (6)
354-GC250703