Documente Academic
Documente Profesional
Documente Cultură
0
®
rap 2
lt co
U E
LEVELLING
COMPOUNDS
C20-F5
1
Rapid hydrating,
fast-drying
self-levelling compound
Ult Eco
– European EN 13813 CT-C20-F5
PRODUCT IDENTITY
Colour: grey
Self-levelling: yes
pH of mix: approx. 12
FINAL PERFORMANCES
• Do not use Ultraplan Eco 20 on metal compounds and traces of paint and gypsum.
surfaces.
Any laitance or weak layers from cement
based surfaces must be removed or where
• Do not use Ultraplan Eco 20 when the
possible, the surface consolidated with
temperature is below +5°C.
Prosfas or Eco Prim PU 1K .
• Do not attempt to apply in large areas Cracks must be first repaired with Eporip.
when the temperature is above +30°C.
Dusty or very porous concrete surfaces must
be cleaned then treated with a coat of
APPLICATION PROCEDURE
Preparing the substrate Primer G (1 part Primer G with 3 parts
The substrates must be sound, dry, free of of water) or Eco Prim T (diluted 1:1 with
dust, loose particles, wax, oils, rust, curing water depending on the type of substrate).
If applying onto ceramic or natural stones, However, the performance of the levelling
apply a coat of Mapeprim SP or Eco Prim T layer in the long term is not significantly
(diluted 1:1 water) after the surface has been affected.
thoroughly cleaned and/or mechanically
abraded. Level with Ultraplan Eco 20 SAFETY INSTRUCTIONS FOR THE
before Mapeprim SP has dried completely PREPARATION AND APPLICATION
(while indents are still possible to make). Ultraplan Eco 20 contains cement that when
in contact with sweat or other body fluids
Preparing the mix
Slowly pour a 23 kg bag of Ultraplan Eco 20 causes irritant alkaline reactions and allergic
into a rust-free bucket containing reactions to those predisposed.
5.5-5.75 litres of clean potable grade water It can cause damage to eyes. During use,
and mix with a low speed electric mixer fitted wear protective gloves and goggles and take
with a suitable mixing paddle to obtain an the usual precautions for handling chemicals.
homogeneous, self-levelling lump free mix. If the product comes in contact with the eyes
Larger quantities of Ultraplan Eco 20 can or skin, wash immediately with plenty of
be prepared in mortar mixers.
After allowing to settle for 2-3 minutes, the water and seek medical attention.
mix should be re-stirred and is then ready
for use. For further and complete information about
the safe use of our product please refer to
The quantity of Ultraplan Eco 20 mixed the latest version of our Safety Data Sheet.
must be used within 20-30 minutes
(at a temperature of +23°C). IIMPORTANT NOTES
Applying the mix Whilst we try to ensure that any advice,
Apply Ultraplan Eco 20 in a single layer of recommendations or information given in our
1 to 10 mm thick with a large metal trowel literature is accurate and correct, we have no
or a squeegee, keeping the trowel slightly control over the circumstances in which our
inclined to obtain the desired thickness. product is used. It is therefore important that
installers satisfy themselves that the product
Ultraplan Eco 20 can also be applied with and conditions are suitable for the envisaged
an automatic pressure pump.
application. No warranty can be given or
Due to its excellent self-levelling characteristic, responsibility accepted other than, that the
Ultraplan Eco 20 immediately eliminates product supplied by us will meet our written
small imperfections (trowel marks, etc.). specification. The installer should ensure that
our latest product data and safety information
If a second layer of Ultraplan Eco 20 is sheets have been consulted prior to use.
required, it is recommended to apply it as
soon as the first one is set to light foot traffic
Please refer to the current version of the
(approx. 3 hours at +23°C). Otherwise if the
previous layer is completely dry, prime with Technical Data Sheet, available from our
Primer G diluted with 1:3 with water after first website www.mapei.com
lightly abrading the surface of the previous
layer or Eco Prim T (diluted 1:1 water). LEGAL NOTICE
The contents of this Technical Data Sheet
The levelling layer of Ultraplan Eco 20 will (“TDS”) may be copied into other project-
be ready to receive ceramic, natural stone
related documents, but the resulting
(non-sensitive) fixed with adhesives after
12 hours at +23°C and resilient flooring, document shall not supplement or replace
carpet, after 24 hours at +23°C (time can vary requirements per the TDS in force at the
depending on the thickness of the levelling, time of the MAPEI product installation.
the room temperature and humidity). The most up-to-date TDS can be down-
loaded from our website www.mapei.com.
CLEANING ANY ALTERATIONS TO THE WORDING
Prior to setting, Ultraplan Eco 20 can be
cleaned and removed from tools and hands OR REQUIREMENTS CONTAINED OR
with water. DERIVED FROM THIS TDS EXCLUDES THE
RESPONSIBILITY OF MAPEI.
CONSUMPTION
1.6 kg/m² per mm of thickness. This symbol is used to identify Mapei products
STORAGE
When stored in dry conditions in the original,
unopened bags, Ultraplan Eco 20 has a All relevant references
shelf life of 12 months. If stored at high for the product are available
temperature and or high humidity conditions upon request and from
the shelf life may be reduced. www.mapei.com
A longer storage period could, determine
a slower setting time of Ultraplan Eco 20.
However, the performance of the levelling
ra
l
Ult Eco
an
p 20