Documente Academic
Documente Profesional
Documente Cultură
T R A N S L AT E
T U E S D A Y, D E C E M B E R 1 3 , 2 0 1 1 Select Language
I finished the project of the most simplest and cheaper modular instrument amplifier. The final amplifier have output C O N TA C T F O R M
power between 70W and 300W for 4 and 8 ohm speakers. Three several modules required for this project if bridged
and paralleled modes required. The 4th module is the speaker protection. The amplifier can be built as:
Single amplifier with only one module with 1 TDA7293 or TDA7294 / channel
Bridged amplifier with 2 modules / channel
Paralleled amplifier with 2 modules / channel
Combined bridged and paralleled with 4 modules / channel
Paralleled simple or bridged amplifier, but with 2 paralleled module
The modules can be connected with 15 pin connectors instead of wires. The single, bridged, and paralleled amplifier
modules are not same, one for the first and the most important "main" module, one for bridge connection, and one for
parallel connection what can be used for both main and bridged modules. The last 4th module is the speaker
protection, must be placed to the middle of stereo configuration between left and right channels.
Contact with blogger if you want to build at your home
these circuit designs. The bottom of posts read the
The official datasheet contains all modes of TDA729x circuits. The TDA7294 is very cheap, but cannot use for table of bare PCB board prices. The PCB/schematic
design not for sale for individuals, I cannot help if you
paralleled mode, and no clipping led output. The recommended max. power supply voltage is +-40V. The TDA7293 need something what is not listed in this blog. If you
have paralleled mode (where only the power stage works, the preamp stages off), the max. power supply voltage is need PCB (not the PCB design) read/search the post of
this site.
+-47V, and clipping led output available. The maximum output power of one circuit is 70-75W of TDA7294, and about • Folow me on G+
• Folow me on Facebook
80-100W of TDA7293.
• Folow me on EEWEB
• EEWB interview
• MSN: rentahost@hotmail.com
The possible output powers of bridged application: • Skype: flywithguitar
• How to order?
SEARCH
Search
SUBSCRIBE RSS
Posts
Comments
P D F M A N U A L S , S C H E M AT I C S
Headphone amplifier with TPA6120
TDA7293 modular amplifier
Expandable modular mixer
The V column is the power supply voltage, 1 means: 1 IC paralleled, 2 means: 2 IC paralleled with all others. Without Modular audio mixer
Modular EQ with gyrators
superscripted number have no parallel connections, this is only bridged.
Audio preamplifiers
UREI 545 and 546 EQ clone
The possible output power with single (non bridged) application: Bridge PA with TDA7294
First MicAmp with INA217
My youtube channel
SHARE MY POST
Like 0 |
More
MOST READED
http://custompcb.blogspot.com/2011/12/modular-tda7293-bridgeparallel.html 1/10
9/23/2018 Custom PCB for DIY electronics: Modular TDA7293 bridge/parallel amplifier
The first and the most important circuit is complete 70-75W amplifier: New power supply with 48V
phantom power and 24V for
relays
I have simple power supply for my
preamplifiers (and all other)
projects, but the 48V phantom
power is missing from this device.
This requi...
Preamplifiers
I finished two of my new projects
with preamplifiers. One of them
contains independent preamplifier
schematics , another one is an
audio mix...
http://custompcb.blogspot.com/2011/12/modular-tda7293-bridgeparallel.html 2/10
9/23/2018 Custom PCB for DIY electronics: Modular TDA7293 bridge/parallel amplifier
2x200W gainclone poweramp
2x400W gainclone poweramp
Simple 5 band EQ
Audio mixer prototype
jFET guitar preamp prototype
The softstart circuit for toroid
My rack mounted power supply
My guitar PA rack
KEYWORDS
pcb (10)
UREI 546 (8)
amplifier (8)
schematic (8)
equalizer (7)
microphone preamplifier (7)
eq (6)
guitar preamplifier (6)
headphone (6)
Modular (5)
parametric equalizer (5)
audio (4)
balanced (4)
mixer (4)
preamplifiers (4)
UREI 545 (3)
math expression (3)
INA217 (2)
alium designer (2)
gyrator (1)
hi-fi (1)
2 N D G U I TA R A M P P R O J E C T
The parts:
To the Conn2 on right edge can be connected another module for bridged or parallel application. It this one main Click to enable Adobe Flash Player
module required (for 75W output power) then Conn2 can be used for speaker protection, but this is not required. The
nother side have Conn4 connector for the second (right) channel is the setup is stereo. This Conn4 connector can be
connected the speaker protection only. For example the simplest stereo setup is: 1 main module for left channel, 1
speaker protection, 1 main module for the right channel. Examples are on the PDF manual. The speaker protection
will be protected bot left and right channels. The wood case for speakers:
On this first PCB the Conn5 connector is the stereo audio level inputs, the right channel wired to the input of another
main module on the right side of speaker protection. The output connector Conn6 is not stereo. This connector can be
user for one channel only (the another output is on the second main module). The single setup uses Out+ and GND,
the bridged setup uses Out+ and Out- for speaker connection.
POSTS
► 2012 (17)
▼ 2011 (19)
▼ December (4)
Failure in the official datasheet of TDA7293
http://custompcb.blogspot.com/2011/12/modular-tda7293-bridgeparallel.html 3/10
9/23/2018 Custom PCB for DIY electronics: Modular TDA7293 bridge/parallel amplifier
TDA7293 for more than 300W (500-600-700W)
New PWM FAN controlers with speaker
protection mod...
Modular TDA7293 bridge/parallel amplifier
► November (7)
► October (8)
AUTHOR'S PROFILE
CO SMI C ANTAGO NIST
VI EW MY COMPLETE PROFILE
http://custompcb.blogspot.com/2011/12/modular-tda7293-bridgeparallel.html 4/10
9/23/2018 Custom PCB for DIY electronics: Modular TDA7293 bridge/parallel amplifier
The Conn4 connector of this bridge PCB can be used for the connection of first main circuit. This module can be
continued by Conn5 connector with speaker protection (if the channel finalized) or with parallel module if more output
current needed.
If the setup must be continued with parallel mode, here is the schematic:
http://custompcb.blogspot.com/2011/12/modular-tda7293-bridgeparallel.html 5/10
9/23/2018 Custom PCB for DIY electronics: Modular TDA7293 bridge/parallel amplifier
This is the simplest module, because the premaplifiers are off within the circuit, only the power FETs working. This
mode controlled by Buffer Driver and Slave mode pins of TDA circuit. This module can be connected to the right side
of main module, bridge module, or if required can be connected to the parallel module to duplicate the paralleled
circuits within the application. The second parallel modules can be continued with speaker protection or with nothing
only. The another edge of the speaker protection (if used) can be restart the full setup with main module for right
channel.
http://custompcb.blogspot.com/2011/12/modular-tda7293-bridgeparallel.html 6/10
9/23/2018 Custom PCB for DIY electronics: Modular TDA7293 bridge/parallel amplifier
Here are the examples how to build complete amplifiers with several output powers with these four modules. The
"Module 1" is always the first and always required main module, the "Module 2" is the optional bridge module, "Module
3" is the optional parallel module can be duplicated within the setup, and the 4th is the speaker protection.
The simplest mono setup (75W on 4 Ohm, with 8 Ohm about half):
1. Module 1
http://custompcb.blogspot.com/2011/12/modular-tda7293-bridgeparallel.html 7/10
9/23/2018 Custom PCB for DIY electronics: Modular TDA7293 bridge/parallel amplifier
2. Speaker protection (optional)
Simple stereo setup (2x 75W on 4 Ohm, with 8 Ohm about half):
1. Module 1
2. Speaker protection (required)
3. Module 1
1. Module 1
2. Module 2
3. Speaker protection (optional)
1. Module 1
2. Module 2
3. Speaker protection
4. Module 1
5. Module 2
1. Module 1
2. Module 3
3. Speaker protection (optional)
1. Module 1
2. Module 3
3. Speaker protection (required)
4. Module 1
5. Module 3
1. Module 1
2. Module 3
3. Module 2
4. Module 3
5. Speaker protection (optional)
1. Module 1
2. Module 3
3. Module 2
4. Module 3
5. Speaker protection
6. Module 1
7. Module 3
8. Module 2
9. Module 3
The parallel module can be connected to the first parallel module for duplication. This increases the maximum current,
maybe smaller output impedance possible.
1. Module 1
2. Module 3
3. Module 3
4. Module 2
5. Module 3
6. Module 3
and the upper setup can be continued with speaker protection and the another edge of speaker protection can be
repeated the same setup for right channel is stereo application required.
See also:
http://custompcb.blogspot.com/2011/12/modular-tda7293-bridgeparallel.html 8/10
9/23/2018 Custom PCB for DIY electronics: Modular TDA7293 bridge/parallel amplifier
TDA7293 for more than 300W
New PWM Fan controller with speaker protection
PDF manual for TDA7293 amplifiers
2 COMMENTS:
A B N 1, 2012 5:47 AM
H , !
C ´ "K " - G , E . I ,
I HIFI- , I ( -/ -
- , , ` , ...).
B , ," " , , PCB ( TOOOO - 5.1
, ... , . 10
OPA2134). A ( ) + TDA7293.
T , ´ - , ...
C ?M ,
, FRED
R
C A N 2, 2012 2:27 AM
H, ,I :
:// . . / / - .
N P H O P
S :P C (A )
http://custompcb.blogspot.com/2011/12/modular-tda7293-bridgeparallel.html 9/10
9/23/2018 Custom PCB for DIY electronics: Modular TDA7293 bridge/parallel amplifier
READERS
Followers (4)
Follow
A N A LY T I C S
http://custompcb.blogspot.com/2011/12/modular-tda7293-bridgeparallel.html 10/10