Documente Academic
Documente Profesional
Documente Cultură
FOR
January 2013
Radegundo S. de Luna
Competent Person for Nickel (PMRC No. 071205)
Licensed Geologist (No. 0000218)
Update on the Mineral Resources of the MMDC Nickel Project
Marcventures Mining & Development Corporation
TABLE OF CONTENTS
1. EXECUTIVE SUMMARY 1
2. INTRODUCTION 4
3. TENEMENT AND MINERAL RIGHTS 5
4. GEOGRAPHIC FEATURES 5
4.1 Location and Accessibility 5
4.2 Topography, Physiography and Drainage 6
4.3 Climate 7
4.4 Vegetation 7
5. PREVIOUS WORK 8
6. HISTORY OF PRODUCTION 10
7. GEOLOGIC SETTING 12
7.1 Regional Geology and Tectonic Setting 12
7.2 Local Geology 15
7.2.1 Dinagat Ophiolite Complex 15
7.2.2 Sohoton Greenschist 16
7.2.3 Alipao Andesite 16
7.2.4 Timamana Limestone 16
8. MINERALIZATION 18
9. EXPLORATION 21
10. DRILLING 22
10.1 Drilling Contractors 24
10.2 Drill hole Collar Survey 26
11. SAMPLING METHOD 26
12. SAMPLE PREPARATION, SECURITY AND ANALYSES 28
13. DATA VERIFICATION 30
14. MINERAL RESOURCE ESTIMATE 31
15. INTERPRETATION AND CONCLUSIONS 33
16. RECOMMENDATIONS 34
17. REFERENCES 35
i
Update on the Mineral Resources of the MMDC Nickel Project
Marcventures Mining & Development Corporation
LIST OF TABLES
LIST OF FIGURES
Figure 1: Location Map of MMDC Tenement Area in Cantilan, Surigao del Sur 4
Figure 2: Road network from Surigao City and Butuan City to MMDC Tenement Area 6
Figure 3: Map showing location of Carac-an River 7
Figure 4: Climate map of the Philippines with relative location of MMDC Tenement Area 8
Figure 5: MMDC Tenement Map showing Cabangahan, Sipangpang and Pili Areas 10
Figure 6: Current Mine site in Cabangahan Area 11
Figure 7: General tectonic map of the Philippines 12
Figure 8: Close-up of the tectonic setting of northern Surigao Peninsula 13
Figure 9: Distribution of ophiolites in the Philippines 13
Figure 10: Updated stratigraphic column of the Northern Pacific Cordillera 15
Figure 11: Geologic map of MMDC Tenement Area 16
Figure 12: Graph of nickel and iron values versus depth 19
Figure 13: Frequency distribution graphs of Nickel and iron values of samples 20
Figure 14: Map showing dominant structures inferred in the vicinity of MMDC area 22
Figure 15: Location map of drill holes in Cabangahan, Sipangpang and Pili 23
Figure 16: Photograph of CDSI drill rig 24
Figure 17: Photograph of Georock drill rig 25
Figure 18: Photograph of portable mechanized auger used by Dr. Arcilla’s Team 25
Figure 19: Photograph of in-house drill rig, YBM 26
Figure 20: Sample of core photograph with label 27
Figure 21: Photograph of MMDC Sample Preparation Facility 28
ii
Update on the Mineral Resources of the MMDC Nickel Project
Marcventures Mining & Development Corporation
Figure 22: Steel plate and electric oven used for sample preparation 28
Figure 23: Crusher and pulverizer used for sample preparation 29
Figure 24: AAS equipment and chemical used for titration 29
Figure 25: Scatter plot for standard samples 30
LIST OF APPENDICES
Appendix 1: Daily Drilling Report, Core Log Form and Sample Submission Form
Appendix 2: Assay results of standard samples
Appendix 3: Sample database used in the resource estimation
iii
Update on the Mineral Resources of the MMDC Nickel Project
Marcventures Mining & Development Corporation
1. EXECUTIVE SUMMARY
On December 2012, Marcventures Mining and Development Coporation (MMDC) requested the
author to update the Competent Person Report on its mineral resource which was filed on August
2010. The first report was written by Dr. Carlo Arcilla, Competent Person for Geology and current
Director of the National Institute of Geological Sciences. The previous resource estimate of Dr.
Arcilla in 2010 reported a total of 3,867,000 dry metric tonnes of Indicated limonite resource at 1.0%
nickel cut-off, averaging 1.3% nickel and 35.9% iron, and 5,635,000 metric tonnes of Indicated
saprolite resource at 1.0% nickel cut-off, averaging 1.4% nickel, within a 120-hectare portion of the
4,799-hectare tenement area. This report discloses the result of exploration carried out by MMDC
from 2010 to 2012 on its Nickel Project as well as the updated resource estimate.
The tenement area is mostly underlain with serpentinized peridotite and dunite of the Dinagat
Ophiolite. Geological mapping and exploratory drilling showed favourable development of iron-rich
limonite ore north of Carac-an River and the occurrence of nickel-rich saprolite ore was observed
south of the said river.
The MPSA area is divided into three sub-areas, namely: 1) Cabangahan, 2) Sipangpang, and 3) Pili. A
total of 1,289 drill holes with an aggregate depth of 21,266.98 meters have been drilled to date.
Combination of compass and tape traverse, and Global Positioning System (GPS) were used primarily
to locate holes at 50-m, 100-m and 200-m interval. Collar coordinates of drill holes at 25-m interval
were obtained using total station. Assay results of Pili and Sipangpang drill holes indicate presence of
high-iron limonite ore in these areas. Cabangahan samples yielded assay results indicative of high-
nickel saprolite ore overlain by high-iron limonite ore.
Core samples from the field were logged and prepared at MMDC Core House and Sample Preparation
Facility located in Sition Banban, Cantilan. Whole-rock chemical analyses of the core samples were
done by Atomic Absorption Spectroscopy (AAS) at MMDC’s Laboratory also located within the
vicinity. Quality analysis/quality control program includes AAS calibration using in-house laterite
standard samples prepared by titration. Statistical evaluation and graphical presentation of 1,059
standards showed excellent correlation for nickel and iron with R2 = 0.99.
The Resources are classified purely as a function of the drilling density. Resource estimation used in
this report is the polygon method in which the classification guidelines applied are consistent with the
CIM or JORC classification standards, to wit:
1
Update on the Mineral Resources of the MMDC Nickel Project
Marcventures Mining & Development Corporation
Measured Resources - for limonite, where drilling is at a grid of 50m x 50m or less
- for saprolite, where drilling is at a grid of 25m x 25m or less
Indicated Resource - for limonite, where drilling is at a grid of up to 100m x 100m
- for saprolite, where drilling is at a grid of up to 50m x 50m
Inferred Resource - for limonite and saprolite, where drilling is at a grid of up to 300m x
300m
Cut-off grade for saprolite estimation is ≥1.5% nickel and <20% iron. While for limonite ore, cut-off
grade used was ≥0.7% nickel and ≥20% iron. Total Measured and Indicated Saprolite Resource
with average 1.90% nickel and 11.81% iron is 2,883,000 WMT. For Limonite Ore, total
Measured and Indicated Resource averaging 1.08% nickel and 44.48% iron is 15,991,000
WMT.
Total Inferred Saprolite Resource with average 1.73% nickel and 13.08% iron is 4,490,000
WMT. For Limonite Ore, total Inferred Resource averaging 1.00% nickel and 47.93% iron is
21,960,000 WMT. Details of the Mineral Resource estimation are shown in Table 1.
2
Update on the Mineral Resources of the MMDC Nickel Project
Marcventures Mining & Development Corporation
3
Update on the Mineral Resources of the MMDC Nickel Project
Marcventures Mining & Development Corporation
2. INTRODUCTION
This technical report was prepared at the request of Mr. Mario G. Vijungco, Chairman and President
of Marcventures Mining and Development Corporation (MMDC), with the purpose of providing an
updated nickeliferrous laterite resource estimate of the MMDC Nickel Project located within the
Municipality of Cantilan and Carrascal in Surigao del Sur (Figure 1).
The author was commissioned by MMDC to complete a review, site visit and technical report on the
mining and exploration activities being undertaken by the company. This technical report, which
complies with the requirements, guidelines and implementing rules and regulation of the Philippine
Mineral Reporting Code (PMRC), relied on the technical reports, opinion and statement of
geologists/consultants of MMDC.
The report also provides detailed summary of the assessment of historical data and results of the
exploration program carried out over the tenement area for the past 2 years after the last competent
person report. This document is compiled from technical reports written by consultants of MMDC,
published technical data and observations made by MMDC geologists. All sources of data used are
herein cited and listed in Section 17.
This technical report is compliant with the implementing rules and regulations of the Philippine
Mineral Reporting Code (PMRC).
4
Update on the Mineral Resources of the MMDC Nickel Project
Marcventures Mining & Development Corporation
MMDC Nickel Project is located within Barangays Cabangahan and Panikian in the Municipalities of
Cantilan and Carrascal, respectively. Cantilan and Carrascal are within the Province of Surigao del
Sur. The project is covered by MPSA 016-93-XI. Table 2 shows the geographic coordinates of the
boundary of the tenement area.
The project area is within a logging concession that was operated by Ventura Timber Corporation
since 1986. Realizing the potential of the area, Ventura Timber Corporation engaged the services of
Geomin Management Corporation in May 1991 to explore the area for possible mineral deposits and
in July 1991, applied for a Mineral Production Sharing Agreement (MPSA) over 4,799 hectares in
accordance with the transitory provision of the 1987 Mining Law known as Executive Order No. 279
(E.O. 279).
4. GEOGRAPHIC FEATURES
The tenement area is located approximately 3 kilometers west of Cantilan along the
Surigao City-Tandag National Highway and accessible through newly renovated
logging roads westward from Barangay Panikian. Surigao del Sur is bordered by
Surigao del Norte to the north, Agusan del Norte and Agusan del Sur to the west, and
Davao Oriental to the south.
5
Update on the Mineral Resources of the MMDC Nickel Project
Marcventures Mining & Development Corporation
Cantilan is accessible from Surigao City by travelling 120 kilometers southward (Figure
2) and from Tandag by land travel for about 60 kilometers northward. Surigao City and
Butuan City can be reached from Manila or Cebu City most conveniently by daily
flights by all major airlines in the country.
Figure 2. Map showing road network from Surigao City and Butuan City to MMDC tenement
area.
The tenement area is located at the north eastern fringe of the Diwata Mountain Range
(also called the Pacific Cordillera), a 300-kilometer stretch of rugged mountains that
extends all the way to Davao. To the west of the Diwata Mountain Range are
topographic low areas, Tubay Valley and Lake Mainit. These areas are bordered to the
west by a 70-kilometer long elevated terrain that runs parallel to the west coast of
Surigao del Norte, the Malimono Ridge.
Within the tenement area, the terrain is generally gently to moderately sloping and
undulating with the exception of some portions in Cabangahan with steep slopes. The
Carac-an River transects the tenement area from west to east (Figure 3). The portion of
the tenement north of the river attain elevations up to 400 meters above sea level while
the portion located south of the river reaches up to 650 meters above sea level. The
6
Update on the Mineral Resources of the MMDC Nickel Project
Marcventures Mining & Development Corporation
Carac-an River merges with the Taracan River to the south and empties into Lanuza
Bay at the east.
Figure 3. Map showing the Carac-an River transecting the tenement area. Also shown are the Eyamjo and
Taracan Rivers.
4.3 Climate
Surigao del Sur exhibits TYPE II Climate which has no pronounced dry and wet season
(Figure 4). Maximum rainfall is experienced from November to February and minimum
rainfall from May to April with annual rainfall not exceeding 4,500 millimeters
(Kintanar, 1984).
4.4 Vegetation
Dense growth of primary forest trees (e.g. narra, lauan, apitong, tangile) covers the
mountainous portions of the tenement. Secondary growth plant covers the logged out
portions of the area. Lowlands are used for agricultural purposes and are cultivated with
7
Update on the Mineral Resources of the MMDC Nickel Project
Marcventures Mining & Development Corporation
rice, corn, coconut and fruit trees. Mangroves are observed to grow along the lower
sections of rivers and coastal areas.
5. PREVIOUS WORK
The potential of the tenement area for nickeliferrous laterite was first recognized in the 1950s when
the Mines and Geosciences Bureau (MGB) delineated areas with potential for laterite in the Surigao
Peninsula. Several companies had taken interest in the property including Surigao Nickel Mining and
Industrial Corporation in a joint venture with Marcopper Mining Corporation (1970s); Ventura
Timber Corporation (1990s) who engaged Geomin Management Corporation to explore the area in
1991, and Queensland Nickel Incorporated and Hinatuan Mining Corporation in 1992.
Table 3 shows the previous exploration works and various resource estimates undertaken for MMDC.
8
Update on the Mineral Resources of the MMDC Nickel Project
Marcventures Mining & Development Corporation
1991 Geomin Area 1, Area 2 45 holes with 200-m grid 0.1 to 13% heavy mineral
Management Corp aggregate spacing fraction, high anomaly in
meterage of central northern part of
275 meters at the area; conducted
300-m grid geological mapping,
petrographic and
mineralogical studies
1992 Hinatuan Mining Area 2 (25 25 holes with 826kg of limonite at 0.9%
has.) depth ranging Ni cut-off, averaging
from 7 to 24 1.16% Ni and 50.7% Fe;
meters 2,044kg of saprolite at
1.6% Ni cut-off, averaging
2.15% Ni
1994 Ventura Timber 1,500 has. 1,000 drill 111 test pits estimated potential
holes ranigng from resource of 100MMT at
6.3 to 14.3 1.5% Ni, 24% Fe and
meters 0.05% Co
Initially, auger drilling and test-pitting was conducted to explore the area. In 1992, Hinatuan Mining
Corporation used portable vibro drills to explore for saprolite and drilled at several random locations.
The drilling program delineated a 120-hectare mineralized zone in Cabangahan, which was then
referred to as ‘Area 2’. The result of this drilling became the basis for the first PMRC-compliant
report of Arcilla in 2010. Figure 5 shows the location of Areas 1, 2, and 3 (or Pili, Cabangahan and
Sipangpang, respectively). A systematic rotary in-fill drilling program was then conducted over
Cabangahan, Sipangpang and Pili from 2010 to 2012. The second-phase exploration yielded 1,289
drill holes with a total meterage of 21,266.98 meters. A total of 21,247 samples were collected which
constitute the basis for the updated resource report of 2012.
9
Update on the Mineral Resources of the MMDC Nickel Project
Marcventures Mining & Development Corporation
Figure 5. MMDC MPSA 016-93-XIII tenement map showing Cabangahan, Sipangpang and Pili areas.
6. HISTORY OF PRODUCTION
MMDC has started its mining operation from the last quarter of 2010 which includes clearing,
grabbing and stockpiling of limonite and saprolite ore from Area 2 (Cabangahan) which is covered by
an ECC (120 has.). By the third quarter of 2011, MMDC was able to start shipping out limonite and
saprolite ore up to the present. MMDC has already shipped nearly 1,300,000 WMT of limonite and
saprolite. This indicates extensive mineralization in the MPSA. Nearly 30% of the shipped ore is
saprolite with an average grade of 1.8% Ni. The rest are limonite with an average grade of 1.01% Ni
and 48.44% Fe. Table 4 summarizes the shipment details of MMDC from 2011 to 2012.
10
Update on the Mineral Resources of the MMDC Nickel Project
Marcventures Mining & Development Corporation
Figure 6. Photograph of the current mine site in Cababangahan area where high-nickel saprolite resource has been
delineated.
11
Update on the Mineral Resources of the MMDC Nickel Project
Marcventures Mining & Development Corporation
7. GEOLOGIC SETTING
The principal tectonic element of the Philippine archipelago is the elongate Philippine
Mobile Belt (Rangin, 1991) which is bound to the east and west by two major
subduction zone systems, and bisected along its north-south axis by the Philippine Fault
(Figure 7).
The Philippine Fault and its associated faults play an important role in the
mineralization of the Surigao District. The trace of the Philippine Fault in Surigao is
marked by the highly rectilinear NNW-SSE trending Tubay Valler, Lake Mainit and
Maniayao Volcano (Figure 8). These structures were formed by a pull-apart mechanism
associated with left-stepping left-lateral strike slip fault.
12
Update on the Mineral Resources of the MMDC Nickel Project
Marcventures Mining & Development Corporation
13
Update on the Mineral Resources of the MMDC Nickel Project
Marcventures Mining & Development Corporation
The basement rocks in the district are basalts and slabs of the Dinagat Ophiolite and
metamorphic rocks of the Cretaceous Sohoton Greenschist. The ophiolite consists of
amphibolite, peridotite, pyroxenite, gabbro and dunite. They are regionally
serpentinized and can be found along Malimono Ridge and Northern Pacific Cordillera.
These rocks were dated to be Cretaceous to Paleocene (MGB, 2010; Rohrlach, 2005).
Overlying the basement rocks are calcareous conglomerates of the Upper Eocene
Madanlog Formation in Surigao, and its equivalent terrigenous and calcareous
sediments of the Nabanog Formation in Agusan. These formations are in turn overlain
by the Late Oligocene to Early Miocene Bacuag Formation. The Bacuag Formation
consists of basaltic flow and breccia, limestone, limestone conglomerate, wackes,
siltstone, and muddy limestone.
Intruding the Bacuag Formation and other older formations is the Asiga Diorite named
after the river where most outcrops were to be found. The Early to Late Miocene Alipao
Andesite also intrudes the Bacuag Formation in the vicinities of Alipao and Siana Mine
Pits. The Bacuag Formation is overlain by the Lower to Middle Miocene Mabuhay
Formation (Motherlode Turbidite by UNDP, 1987). The Middle Miocene Timamana
Limestone inconformably overlies the Bacuag and Mabuhay Formations. This consists
of massive coralline limestone (MGB, 2010).
Andesitic pyroclastic eruption and lava flows formed the Tugunan Formation
(Mabuhay Clastics by UNDP, 1987) during the Pliocene. Associated magmatism
brought about the epithermal mineralization of the Surigao District (Rohrlach, 2005),
and produced the andesites reported as the Andesite Group by Santos et.al. (1962) and
as the Andesite Series by Santos-Ynigo (1944). These were separated by MGB (2010)
into the Early to Late Pleistocene Ipil Andesite, Late Pliocene Bad-as Dacite and the
Pleistocene Maniayao Andesite. Pleistocene deposits in the region are the Mainit
Formation, Hinatigan Formation and Placer Conglomerate (MGB, 2010), all of which
are dominated by conglomerates and sandstones. Figure 10 shows the updated
stratigraphic column of the Northern Pacific Cordillera by MGB, 2010.
14
Update on the Mineral Resources of the MMDC Nickel Project
Marcventures Mining & Development Corporation
In summer of 2012, students from the National Institute of Geological Sciences (NIGS)
conducted geological and structural mapping within the MPSA area under the
supervision of Dr. Carlo Arcilla. Figure 11 shows the location and inferred boundaries
of the different lithologic units as mapped by the group.
15
Update on the Mineral Resources of the MMDC Nickel Project
Marcventures Mining & Development Corporation
Panikian. The rock units were also observed in Barangays Sipangpang and
Cabangahan located south of the MPSA area.
16
Update on the Mineral Resources of the MMDC Nickel Project
Marcventures Mining & Development Corporation
and low grade metamorphic rocks are distributed over the northwestern part
of Cabangahan in the vicinity of Sipangpang River.
The Alipao Andesite intrudes all older units and assigned to a Middle
Miocene age by UNDP (1987). Outcrops are found in the northwestern part
of the Cabangahan area, south of the metavolcanics and phyllite area. Minor
andesite dikes and outcrops are found along the Carac-an River in Lubo near
the metavolcanics zone. Rock samples are gray to greenish in color with no
observed manifestation of metamorphism. Texture is aphanitic to porphyritic
with long amphibole phenocrysts in fine-grained matrix.
17
Update on the Mineral Resources of the MMDC Nickel Project
Marcventures Mining & Development Corporation
8. MINERALIZATION
Nickel/Iron deposits in the MMDC tenement area are in the form of laterite (limonite ore) and
saprolite derived from the physical and chemical weathering in place of the underlying ultramafic
rocks, the bulk of rock suites of the Dinagat Ophiolite Complex. Laterites are accumulation of the
residual product of the upper oxidizing zone in the weathering profile. It is essentially made up of clay
and other oxide minerals rich in iron. The lower reducing zone directly underlying the laterite is the
saprolite, a secondary nickel enriched zone made up of rocks and clay in silicate form. They are
surface and near surface deposits localized by topographic controls and geologic structures.
The typical laterite deposit at Cabangahan mining pit shows distinct color variation with depth, to wit:
1) a pale yellowish and light brown upper to near surface laterite, 2) a middle section of a yellowish
laterite, and 3) a multi-colored bottom laterite. The color described is the gross effect of several colors
as viewed in its totality. However, a closer examination of the laterite would reveal various shades of
red, brown, orange, yellow and gray. They appear as alternating bands, streaks, oolites, lenses and
mottled colors. Occasional chromite, magnetite, manganese specks are noted.
Underlying the laterite is saprolitic layer with grey to greenish brown color. It has low plasticity and
consists of partly decomposed rocks, softly clayey rock, boulders rimmed by decomposed materials
with fairly unweathered core and clast of bedrock. This is a zone characterized by rapid changes in
physical properties and chemical composition. The saprolite layer may reach up to more than 8 meters
thickness in some portion of the tenement area. Garnierite was also observed in the saprolite layer. It
occurs as irregular fracture filling, lenses and paper thin coating in joints and layering structures.
Results of X-ray Diffraction (XRD) of a garnierite sample taken from the tenement area showed that
the garnierite consists mostly of lizardite (magnesium-dominant serpentine), remnants of forsterite
(magnesium-dominant olivine), augite (calcic magnesium-iron clinopyroxene), and traces of
magnetite. Geothite was also found as an alteration product of olivine.
Nickel is relatively mobile over a wide range of environment. Its fixation in the laterite zone is in
oxide form. Nickel is absorbed and included in the goethite and other oxide form. Its values generally
increase with depth and attain maximum values at the saprolite layer. Its concentration in the laterite
is not high compared to that in the saprolite. Iron content is highest in the laterite zone and remains so
in the laterite column with small variation but decreases rapidly from the bottom of the laterite to the
saprolite zone (Figure 12).
18
Update on the Mineral Resources of the MMDC Nickel Project
Marcventures Mining & Development Corporation
Nickel and iron grade distributions shown in Figure 13 show that Cabangahan Area contains the most
saprolite samples. This is manifested by higher number of iron values around 5 to 15 percent in
Cabangahan distribution graph than at around 45 to 55 percent. Likewise, abundance of nickel values
from 1.5 to 3 percent also denote high number of saprolite samples.
The iron grade distribution shows the typical trend observed for most laterite deposits in the country.
However, trend of nickel grade distribution observed so far in other laterite deposits in the country
show normal or bell-shaped distribution with the peak at medium grades or around 1 percent. In the
distribution graph above, there is an unusual peak at low nickel values of 0.2 to 0.5 percent. This does
not indicate predominant low grades in the area, but instead indicates an unusually high number of
bedrock samples drilled.
19
Update on the Mineral Resources of the MMDC Nickel Project
Marcventures Mining & Development Corporation
Frequency
Frequency
800
600 2000
400
1000
200
0 0
0.00
0.30
0.60
0.90
1.20
1.50
1.80
2.10
2.40
2.70
3.00
22.5
37.5
52.5
0
15
30
45
60
7.5
% Nickel % Iron
800 1000
600
400 500
200
0 0
1.50
0.00
0.30
0.60
0.90
1.20
1.80
2.10
2.40
22.5
37.5
52.5
0
7.5
15
30
45
60
% Nickel % Iron
100 400
300
50 200
100
0 0
0.00
0.30
0.60
0.90
1.20
1.50
1.80
2.10
2.40
22.5
37.5
52.5
0
7.5
15
30
45
60
% Nickel % Iron
Figure 13. Frequency distribution graphs of Nickel and Iron values of samples from Cabangahan, Sipangpang and Pili Areas.
20
Update on the Mineral Resources of the MMDC Nickel Project
Marcventures Mining & Development Corporation
9. EXPLORATION
The MMDC Nickel Project denominated as MPSA 016-93-XIII was registered on July 1993.
Community information and education campaigns commenced and have continued since that time.
All exploration work on the MMDC Nickel Project was carried out under the supervision of Mr.
Mario G. Vijungco, Chairman and President of Marcventures Mining and Development Corporation.
Assessment and review of related literature and available data on geology of the area was carried out
initially.
Detailed geologic mapping on a local scale was conducted by Dr. Arcilla’s Team in April 2012. The
team consists of 58 students supervised by 10 faculty members, 2 of which are licensed geologists,
and 2 representatives from MMDC. The activity included geologic mapping using 10,000-scale base
map and sampling within the tenement area. The main purpose of the mapping activity is to identify
different rock types and structures including fractures, joints and faults. Trend of structures were
measured using brunton compass and plotted on map using coordinates derived from Global
Positioning System (GPS) devices. Displacements were inferred by observing offset in the structures.
Stress orientation was determined by plotting the structures on rose diagrams; thence, the prevailing
stress regime in the area was determined.
A northeast-southwest lineament that extends from the General Islands toward Panikian which
appears to end southwest of Cabangahan was identified as the most prominent structure within the
vicinity of the tenement area (Figure 14). The structure is inferred to be the contact between the
limestone and ultramafics. Similar trending joints were found in the limestones while northwest-
southeast joints were found to be more dominant in ultramafic rocks.
While the sense of movement of several faults was difficult to ascertain due to lack of reference
bedding planes, high degree of weathering of outcrop, and relatively thick gouge; analysis of a left-
lateral fault in an outcrop south of Cabangahan together with faults with available rake data suggests a
primary compressive stress trending along the NW-SE.
21
Update on the Mineral Resources of the MMDC Nickel Project
Marcventures Mining & Development Corporation
Figure 14. Map showing dominant structures inferred in the vicinity of MMDC tenement area (Arcilla et.al., 2012).
10. DRILLING
Based on previous drilling by Hinatuan Mining Corp. and other exploration activities, MMDC
conducted extensive diamond drilling on the whole tenement area from 2010 to the last quarter of
2012 to further increase its mineral resource. Three (3) drilling contractors utilizing at least 10 drill
machines each, and 5 in-house YBM drill machines were used.
For the current resource estimate update, a total of 1,289 vertical holes have been completed covering
Cabangahan, Sipangpang, and Pili (Figure 15). Holes within Cabangahan area are located on 25-m to
100-m grid, in Sipangpang on 50-m to 100-m grid, and in Pili on 100-m to 200-m grid. Total
meterage is 21,266.98 with an average depth of 16.50 meters per hole and maximum of 40.0 meters.
Table 5. Summary of driling activities conducted over Cabangahan, Sipangpang and Pili Areas.
Depth Samples
Area No. of holes Total Min Max Average Total %Ni range %Fe range
Cabangahan 1,009 17,095.88 3 34 16.56 17,080 0.01-3.16 0.01-57.48
Sipangpang 231 3,091.30 4 28 13.38 3,088 0.01-2.73 3.35-55.27
Pili 49 1,079.80 7 40 22.04 1,079 0.01-1.80 0.42-53.82
TOTAL 1,289 21,266.98 21,247
22
Update on the Mineral Resources of the MMDC Nickel Project
Marcventures Mining & Development Corporation
Figure 15. Location map showing 1,289 drill holes completed from 2010 to 2012. The blue outline within Cabangahan indicates the 120-
hectare ECC Area where the current mining operations is located.
23
Update on the Mineral Resources of the MMDC Nickel Project
Marcventures Mining & Development Corporation
Construction and Drilling Specialist, Inc. (CDSI) was contracted to undertake coring
using a minimum of ten (10) units of man-portable drilling machines complete with HQ
or NQ triple-tube core barrels to ensure high percentage of core recovery. CDSI was
able to complete 66 holes in Cabangahan, 49 holes in Pili and 32 holes in Sipangpang
from June to September 2011. The table below lists the drill rigs used by CDSI during
the activity.
Figure 16. (LEFT) Photograph of drill hole location taken before drilling. (RIGHT) Sample of CDSI drill rig employed
by the contractor.
24
Update on the Mineral Resources of the MMDC Nickel Project
Marcventures Mining & Development Corporation
A total of 215 drill holes were completed by Georock Construction and Development
Corporation from July to November of 2011 covering Sipangpang area. The contractor
employed 10 units of Koken Mechanical Drill Machine, YBM Hydraulic Drilling
Machine, Kano Hydraulic Drilling Machine producing NQ size (45mm) core.
Figure 17. (LEFT) Sample of drill rig used by the contractor, Georock, in Sipangpang area specifically drill hole ID Sip-
42. (RIGHT) Close-up photo of Georock drill rig.
Dr. Arcilla conducted in-fill drilling within the Sipangpang and Cabangahan Area from
April to November 2012. A total of 351 drill holes were completed during that period
with a total of 5,420.00 meters. His team used 22 units of portable mechanized auger
drill with NQ-sized single tube core barrel.
25
Update on the Mineral Resources of the MMDC Nickel Project
Marcventures Mining & Development Corporation
The in-house drilling team of MMDC conducted the in-fill drilling at 25-m interval
over the saprolite-rich area within Cabangahan and completed 630 holes over the area.
The team utilized 5 YBM drill units with BQ size single tube core barrel (Figure 19).
Collar data of holes at 50-m, 100-m and 200-m grid were gathered using a Geographic
Positioning System (GPS) device.
Drill hole collar data, including position and elevation, of holes spaced at 25-m grid
was surveyed by MMDC surveyors using 2 units of Topcon total station (GPT-3107N
and GTS-100N). Two bench marks were established by the surveyors to be used as tie
point. Reference system used is PRS 92 or the Luzon-Mindanao datum.
Initial Drilling and Sampling Procedures was set up by MMDC personnel and was adapted from
2007. The protocols were re-evaluated and improvements were implemented by October 2012. The
procedures for core handling, logging and sampling applied by MMDC are briefly described below.
It is standard procedure that a representative from MMDC, either geologist or core checker, is present
on every drill rig during coring operation. This is to record drilling activities such as core recovery,
26
Update on the Mineral Resources of the MMDC Nickel Project
Marcventures Mining & Development Corporation
drill run, type of material recovered including problems encountered during drilling. These data are
recorded into the Daily Drilling Report (Appendix 1). Once a core box is filled, it is sealed with a
wooden board then secured with rubber packing band. A specific vehicle is assigned to transfer core
box from the field to the core house located within MMDC camp site in Sitio Banban.
Upon arrival at the core house, core box filled with samples are received by the Core House Lead
Man and recorded in a logbook. Meterage of core samples is checked against core blocks and the
Daily Drilling Report. After checking, core boxes are photographed with the proper drill hole ID,
project area, meterage and box number written on a white board label placed on top of the core box
(Figure 20).
Figure 20. Sample core photograph with drill hole ID, project area, meterage and box
number indicated in the white board label.
Core logging is carefully done in the core house by MMDC geologist. The geologist is guided by
different codes for laterite horizon classification, weathering scale, boulder size and color which are
readily available in the Core Log Sheet (Appendix 1).
Once core logging is done, the geologist determines the sample interval and records it in the Core Log
Sheet (Appendix 1) to be used as reference by the Samplers. Sampling is done at a nominal interval of
one meter down the hole regardless of laterite horizon boundaries. The core house sampler uses
spatula and sample pick to split the sample along the length and collect the samples from the left side.
27
Update on the Mineral Resources of the MMDC Nickel Project
Marcventures Mining & Development Corporation
Samples are placed into pre-labelled plastic sample bags and delivered to the Sample Preparation
Facility of MMDC which is supervised by the company chemist.
Figure 21. Photograph of MMDC Sample Preparation Facility in Sitio Banban. Sacks in front of the
facility contains the samples that were submitted.
MMDC QA/QC procedures were also diligently followed in the sample preparation and security
procedures. Split core samples from the core house are received by the Sample Prep Men and are
verified from the Sample Submission Form (Appendix 1) submitted by the Core House Lead Man.
Figure 22. (LEFT) Samples are manually crushed on steel plate installed on the floor of the Sample Preparation
Facility. (RIGHT) Metal trays with samples are place into the electric oven to be heated at 105°C for 8 hours.
28
Update on the Mineral Resources of the MMDC Nickel Project
Marcventures Mining & Development Corporation
The sample is manually crushed on a steel plate using sledge hammer then placed on metal trays. To
dry the samples, metal trays containing the samples are placed into the electric oven at 105°C for 8
hours or more if needed.
Figure 23. (LEFT) Crusher used to reduce the size of the sample after drying. (RIGHT) Pulverizer used to
further reduce the size of the sample after splitting.
The sample is then passed through a crusher to crush “the lumps” that were formed while drying the
sample. A riffle splitter is used to divide the sample into two parts. One part is retained and stored as
coarse reject that can be used for check analysis in the future. The other part is pulverized to 150 mesh
where about 1 gram sample is taken to be analysed.
Analyses of core samples are performed by the MMDC Laboratory using Atomic Absorption
Spectrometry (AAS).
Figure 24. (LEFT) Atomic Absorption Spectrometry (AAS) equipment installed at the MMDC Laboratory in Sitio
Banban. (RIGHT) Chemicals used for titration.
29
Update on the Mineral Resources of the MMDC Nickel Project
Marcventures Mining & Development Corporation
The author has observed and verified the datasets provided by MMDC against original field sheets
and official assay results. Core trays were visually inspected against core logs and selected drill hole
collars were inspected in the field and cross checked against survey plans and topographic data.
MMDC In-house laboratory regularly insert nickel standards for every 10 samples. A total of 1,059
standards, representing 5% of the total 21,247 core samples, were inserted. In-house standards were
established through series of analysis by four (4) chemists using AAS and Titration methods. All
assay results fall within the allowable range of ±0.03% for nickel and ±0.30% for iron were
considered. Standards used for the whole drilling course to date range from 0.25 to 2.40% nickel.
Figure 23 shows excellent correlation for nickel and iron of the standards that were analysed with R 2
being 0.99.
3.00 60.00
2.50 50.00
2.00 40.00
Reassay
Reassay
1.50 30.00
1.00 20.00
y = 0.9992x - 3E-05 y = 0.9975x + 0.0493
0.50 R² = 0.9989 10.00
R² = 0.9997
0.00 0.00
0.00 1.00 2.00 3.00 0.00 10.00 20.00 30.00 40.00 50.00 60.00
accepted value Accepted value
Figure 25. Scatter plot of % nickel and iron values of the standard samples used for QA/QC showing excellent correlation,
R2 = 0.99 both for nickel and iron. Standards are inserted every 10 samples.
Ni % Fe %
Relative Percent Error -0.19 0.13
Accepted value = Assay result 208 19
Accepted value < Assay result 382 479
Accepted value > Assay result 438 550
The Relative Percent Errors shown in Table 7 are below 1%, showing consistent and high precision
repeatability. A negative RE% value indicates that the accepted value is higher than the reassay.
Therefore, standards suggest that the analyses of MMDC Laboratory are suitably precise. Further
proof of the accuracy and precision of MMDC Laboratory and sampling practices is that purchasers of
30
Update on the Mineral Resources of the MMDC Nickel Project
Marcventures Mining & Development Corporation
the nickel ore conduct their own determination of grade and tonnage of materials transported in each
shipment and the values determined by the purchasers agree with MMDC’s data.
The data set in Microsoft Excel format used as basis for the resource estimation was provided by
MMDC in December 2012. The spreadsheets contained collar, survey and assay data which consists
of drill hole ID, northing and easting, from and to depth of each sample, and nickel and iron
percentage of each samples.
All holes were drilled vertically. No downhole survey was carried out which is acceptable due to
relatively short length of drill holes.
Polygon method was used to estimate the mineral resource of MMDC’s MPSA 016-93-XIII. In this
method, each drill hole is assigned a polygon that represents the extent of the area of influence of the
drill hole. The assumption is that everywhere within the polygon, the thickness and grade of the
resource material is uniform and more or less the same to the resource material of the drill hole
enclosed by the polygon.
The area of influence of each drill hole is based on the halfway rule, which states that the influence of
a drill hole sample extends until halfway to other samples laterally adjacent to it. For saprolite, the
Measured Mineral Resource was estimated using data of drill holes at 25-m interval and the Indicated
Mineral Resource at 50-m interval while Inferred Mineral Resource was estimated for holes at 100-m
and 200-m interval. In case of limonite, Measured Mineral Resource was estimated using data of drill
holes at 25-m and 50-m interval. Indicated Mineral Resource was estimated using data of drill holes at
100-m interval while Inferred Mineral Resource was estimated for holes at 200-m interval.
The volume of each block is the product of the area of influence and the combined thickness of
samples that fall within the set cut-off grades of each ore type. To determine the Wet Total Tonnage,
the total in-situ volume is multiplied to a swell factor of 1.35 and 1.37 for soft and hard materials,
respectively, and to the bulk density of 1.11 and 1.46, again for soft and hard materials, respectively.
The soft materials contain about 38% moisture while hard materials contain about 15% moisture.
Cut-off used for saprolite ore estimation is ≥1.5% nickel and <20% iron while for limonite ore, cut-off
grade used was ≥0.7% nickel and ≥20% iron. A total of 2,882,000 WMT (wet metric tonnes) of
31
Update on the Mineral Resources of the MMDC Nickel Project
Marcventures Mining & Development Corporation
Measured and Indicated Saprolite Resource with average 1.9% nickel and 11.88% iron was
calculated. For limonite ore, Measured and Indicated Resource was estimated at 15,992,000 WMT
averaging 1.08 percent nickel and 44.48 percent iron. Details of sample data used in the resource
estimation are shown in Appendix 3.
32
Update on the Mineral Resources of the MMDC Nickel Project
Marcventures Mining & Development Corporation
Widespread occurrence of serpentinized peridotite and dunite comprise the lithology in the MMDC
tenement area. High-iron limonite ore and high-nickel saprolite are present over most of the tenement
area.
The Cabangahan Area (Figure 13) hosts high-nickel saprolite and has been mined from 2011 up to
present. Additional drilling outside the present mine site has delineated additional high-iron limonite
ore. The summary of the mineral resource estimation results is presented in Table 8.
Table 9. Comparison of R. de Luna’s 2012 resource estimates with Dr. Arcilla's 2010 resource estimates.
Table 9 shows the comparison between the 2010 mineral resource estimate by Dr. Arcilla and 2012
mineral resource estimate by R. de Luna. There is notably a great increase in the high-iron limonite
ore resource from 2010 with 3.87 Million metric tonnes (1.3% Ni and 35.9% Fe), to 15.99 Million
33
Update on the Mineral Resources of the MMDC Nickel Project
Marcventures Mining & Development Corporation
wet metric tonnes (1.08% Ni, 44.48% Fe) in 2012. This is primarily due to the extensive drilling that
was done outside the 120-hectare ECC area.
The decrease in the saprolite resource is due to higher nickel cut-off used during the 2012 estimation.
Another factor is the reduction of saprolite resource due to production. Some of the saprolite resource
from the 2010 estimation has already been mined and shipped out. The potential for obtaining
substantially more saprolite ore tonnage is shown by the 4.48 Million WMT of Inferred Resource.
More detailed drilling would increase the saprolite resource tonnage considerably.
16. RECOMMENDATIONS
Additional exploration and drilling is recommended over the Pili and Sipangpang Areas to upgrade
the resources from Indicated and Inferred to Measured and Indicated. This will increase the shippable
high-iron limonite ore tonnage.
In-fill drilling is needed in Cabangahan where high-nickel saprolite has been delineated to upgrade the
4.48 Million WMT Inferred saprolite resource into Measured and Indicated resource.
Additional QA/QC method needs to be implemented to also check for accuracy of MMDC Laboratory
given that standard samples only check for analytical precision. Other method that can check for
accuracy is insertion of Certified Reference Materials and inter-laboratory check analysis. Insertion of
geological Blank Sample should also be considered to check and monitor contamination during
sample preparation. Coarse and Pulp Duplicate Samples will check for error in sample size reduction
and error in analyses.
34
Appendix 1
TIME DEPTH
%
From To From To RUN REC RECOVERY LITH Remarks
Operator:
Crew: Conforme (Operator):
Name &Signature
Form 2
rock fragments
Weathering of
Sample ID
fragments
Lithology
Page 1 of 10
Appendix 2 MMDC Standards
Page 2 of 10
Appendix 2 MMDC Standards
Page 3 of 10
Appendix 2 MMDC Standards
Page 4 of 10
Appendix 2 MMDC Standards
Page 5 of 10
Appendix 2 MMDC Standards
Page 6 of 10
Appendix 2 MMDC Standards
Page 7 of 10
Appendix 2 MMDC Standards
Page 8 of 10
Appendix 2 MMDC Standards
Page 9 of 10
Appendix 2 MMDC Standards
Page 10 of 10
Appendix 3 Sample Database
Page 1 of 118
Appendix 3 Sample Database
Page 2 of 118
Appendix 3 Sample Database
Page 3 of 118
Appendix 3 Sample Database
Page 4 of 118
Appendix 3 Sample Database
Page 5 of 118
Appendix 3 Sample Database
Page 6 of 118
Appendix 3 Sample Database
Page 7 of 118
Appendix 3 Sample Database
Page 8 of 118
Appendix 3 Sample Database
Page 9 of 118
Appendix 3 Sample Database
Page 10 of 118
Appendix 3 Sample Database
Page 11 of 118
Appendix 3 Sample Database
Page 12 of 118
Appendix 3 Sample Database
Page 13 of 118
Appendix 3 Sample Database
Page 14 of 118
Appendix 3 Sample Database
Page 15 of 118
Appendix 3 Sample Database
Page 16 of 118
Appendix 3 Sample Database
Page 17 of 118
Appendix 3 Sample Database
Page 18 of 118
Appendix 3 Sample Database
Page 19 of 118
Appendix 3 Sample Database
Page 20 of 118
Appendix 3 Sample Database
Page 21 of 118
Appendix 3 Sample Database
Page 22 of 118
Appendix 3 Sample Database
Page 23 of 118
Appendix 3 Sample Database
Page 24 of 118
Appendix 3 Sample Database
Page 25 of 118
Appendix 3 Sample Database
Page 26 of 118
Appendix 3 Sample Database
Page 27 of 118
Appendix 3 Sample Database
Page 28 of 118
Appendix 3 Sample Database
Page 29 of 118
Appendix 3 Sample Database
Page 30 of 118
Appendix 3 Sample Database
Page 31 of 118
Appendix 3 Sample Database
Page 32 of 118
Appendix 3 Sample Database
Page 33 of 118
Appendix 3 Sample Database
Page 34 of 118
Appendix 3 Sample Database
Page 35 of 118
Appendix 3 Sample Database
Page 36 of 118
Appendix 3 Sample Database
Page 37 of 118
Appendix 3 Sample Database
Page 38 of 118
Appendix 3 Sample Database
Page 39 of 118
Appendix 3 Sample Database
Page 40 of 118
Appendix 3 Sample Database
Page 41 of 118
Appendix 3 Sample Database
Page 42 of 118
Appendix 3 Sample Database
Page 43 of 118
Appendix 3 Sample Database
Page 44 of 118
Appendix 3 Sample Database
Page 45 of 118
Appendix 3 Sample Database
Page 46 of 118
Appendix 3 Sample Database
Page 47 of 118
Appendix 3 Sample Database
Page 48 of 118
Appendix 3 Sample Database
Page 49 of 118
Appendix 3 Sample Database
Page 50 of 118
Appendix 3 Sample Database
Page 51 of 118
Appendix 3 Sample Database
Page 52 of 118
Appendix 3 Sample Database
Page 53 of 118
Appendix 3 Sample Database
Page 54 of 118
Appendix 3 Sample Database
Page 55 of 118
Appendix 3 Sample Database
Page 56 of 118
Appendix 3 Sample Database
Page 57 of 118
Appendix 3 Sample Database
Page 58 of 118
Appendix 3 Sample Database
Page 59 of 118
Appendix 3 Sample Database
Page 60 of 118
Appendix 3 Sample Database
Page 61 of 118
Appendix 3 Sample Database
Page 62 of 118
Appendix 3 Sample Database
Page 63 of 118
Appendix 3 Sample Database
Page 64 of 118
Appendix 3 Sample Database
Page 65 of 118
Appendix 3 Sample Database
Page 66 of 118
Appendix 3 Sample Database
Page 67 of 118
Appendix 3 Sample Database
Page 68 of 118
Appendix 3 Sample Database
Page 69 of 118
Appendix 3 Sample Database
Page 70 of 118
Appendix 3 Sample Database
Page 71 of 118
Appendix 3 Sample Database
Page 72 of 118
Appendix 3 Sample Database
Page 73 of 118
Appendix 3 Sample Database
Page 74 of 118
Appendix 3 Sample Database
Page 75 of 118
Appendix 3 Sample Database
Page 76 of 118
Appendix 3 Sample Database
Page 77 of 118
Appendix 3 Sample Database
Page 78 of 118
Appendix 3 Sample Database
Page 79 of 118
Appendix 3 Sample Database
Page 80 of 118
Appendix 3 Sample Database
Page 81 of 118
Appendix 3 Sample Database
Page 82 of 118
Appendix 3 Sample Database
Page 83 of 118
Appendix 3 Sample Database
Page 84 of 118
Appendix 3 Sample Database
Page 85 of 118
Appendix 3 Sample Database
Page 86 of 118
Appendix 3 Sample Database
Page 87 of 118
Appendix 3 Sample Database
Page 88 of 118
Appendix 3 Sample Database
Page 89 of 118
Appendix 3 Sample Database
Page 90 of 118
Appendix 3 Sample Database
Page 91 of 118
Appendix 3 Sample Database
Page 92 of 118
Appendix 3 Sample Database
Page 93 of 118
Appendix 3 Sample Database
Page 94 of 118
Appendix 3 Sample Database
Page 95 of 118
Appendix 3 Sample Database
Page 96 of 118
Appendix 3 Sample Database
Page 97 of 118
Appendix 3 Sample Database
Page 98 of 118
Appendix 3 Sample Database
Page 99 of 118
Appendix 3 Sample Database