Documente Academic
Documente Profesional
Documente Cultură
Engine
Model ............................................................... TD40GA
Idle, r/s (rpm)
– low idling, ................................................... 12.5 ±0.5 (750 ±30)
– high idling, ................................................... 38.2 ±0.8 (2290 ±50)
Compression pressure at starter motor
revs, variation between cylinders
shall not exceed, kPa (psi)............................... 350 (51)
Valve clearence, in/out, mm/(in) ...................... 0.20 (0.008) / 0.45 (0.018)
Injectors, opening pressure, MPa (psi) ............
– basic ............................................................ 25.3 ±0.5 (3669 ±73 )
Pump timing (injection advance)...................... 18° ±2° B.T.D.C.
Lubricating oil pressure, kPa (psi) low idle ...... 75 (11)
minimum at high idling ..................................... 280 (41)
Engine
Model ............................................................... TD40KAE
Idle, r/s (rpm)
– low idling, ................................................... 12.5 ±0.5 (750 ±30)
Low emission .................................................. 40.0 ±0.8 (2400 ±50)
Compression pressure at starter motor
revs, variation between cylinders
shall not exceed, kPa (psi)............................... 350 (51)
Valve clearence, in / out, mm / (in) .................. 0.20 (0.008) / 0.45 (0.018)
Injectors, opening pressure, MPa (psi) ............
– low emission................................................ 25.3 ±0.5 (3669 ±73)
Pump timing, basic .......................................... 9° ±0.5°
Lubricating oil pressure, kPa (psi) low idle ...... 75 (11)
minimum at high idling ..................................... 280 (41)
Engine
Model ............................................................... TD40GFE
Idle, r/s (rpm)
– low idling, ................................................... 12.5 ±0.5 (750 ±50)
– high idling, ................................................... 38.8 ±0.8 (2330 ±50)
Compression pressure at starter motor
revs, variation between cylinders
shall not exceed, kPa (psi)............................... 350 (51)
Valve clearence, in / out, mm / (in) .................. 0.20 (0.008) / 0.45 (0.018)
Injectors, opening pressure, MPa (psi) ............ 290 (42050)
Lubricating oil pressure, kPa (psi) low idle ...... 50 (73)
high idling......................................................... 300-600 (44-87)
Electrical system
Type / system voltage...................................... Alternating current / 24 V
Alternator, output / current intensity................. 1680 W / 60 A
Battery electrolyte density when fully
charged............................................................ 1.275-1.285
Battery capacity ............................................... 2 x 105 Ah
Hydrostatic transmission
Pump
Pump feed pressure, MPa (psi) ....................... 2.6 ±2 (377 ±290)
Pressure cut-off, MPa (psi) .............................. 42.6 ±1 (6163 ±145)
at 2000 ±100 rpm
Stall diagram, MPa, (psi) ................................. 10.0 ±2.2 (1450 ±319) at 900 rpm
Stall diagram, MPa (psi) .................................. 40.0 ±3.5 (5800 ±508) at 1800 rpm
Motor
Change-over pressure dynamic, MPa (psi) ..... 26.5 ±1.0 (3843 ±145)
Change-over pressure static, MPa (psi) .......... 26.5 ±1.0 (3843 ±145)
Gearbox
Model ............................................................... HST - 75
Clutch pressure low and high gear,
– Low idling speed MPa (psi) ......................... 2.1 ±0.2 (305 ±29)
– High idling speed MPa (psi) ........................ 2.2 ±0.2 (319±29)
Lubrication oil pressure, MPa (psi) .................. 0.03-0.05 (4.35-7.25)
Drive axles
Model / Product No.,
front.................................................................. AWB 10 (23819)
front, with differential lock ................................ AWB 10 (23836)
rear .................................................................. AWB 10 (23820)
front, with limited slip ....................................... AWB 10 (23870)
rear, with limited slip ........................................ AWB 10 (23868)
Brakes
Type................................................................. Dual circuit, fully hydraulic
Wet-disc brakes and pressure accumulators
Accumulator, type ............................................ Diaphragm accumulator
precharging pressure, minimum, MPa (psi)..... 3.5 (508)
precharching pressure, new, MPa (psi) ........... 5.0 (725)
Cut-out pressure, MPa (psi)............................. 13.7 ±0,3 (1987 ±44)
Cut-in pressure, MPa (psi)............................... 12.0 (1740.5 ±44)
Max. output brake pressure, MPa (psi)............ 15.0 ±0.5 (2175 ±73)
Brake pressure, out, MPa (psi) ........................ 8.0 ±0.6 (1160 ±87)
Low pressure indication at, MPa (psi).............. 9.0 ±0.5 (1305 ±73)
Brake disc wear minimum disc thickness,
mm (in)............................................................. 7.2 (0.283)
New disc, mm (in) ............................................ 8.5 ±0.08 (0.335 ±0.003)
Steering system
Stand-by pressure, MPa (psi) .......................... 3.2 ±0.8 (464 ±116)
Max. working pressure, MPa (psi) ................... 21.0 ±0.5 (3046 ±73)
Shock pressure, MPa (psi) .............................. 28.0 ±0.5 (4061 ±73)
Air condition
Filling amount R134a....................................... 2.0 ±0.1 kg
Tightening torques
Cylinder head .................................................. N m (lbf ft)
First tightening,gradually until ......................... 110 (81)
Second tightening ........................................... 110 (81)
Final tightening, angular tightening.................. 180°
Injectors, nut for attaching screws ................... 12 (9)
Wheel nuts, front / rear .................................... 600 (443)
Measurements
mm in mm in