Documente Academic
Documente Profesional
Documente Cultură
7000 118-363 C1
Instruction
Physical VHF Transceiver
R5 SUPREME AIS Transponder Frequency 156-163 MHz
Size W x H x D: 227x77x192 [mm] Output power 1/12.5 W
This quick installation guide serves as a complement to R5 SUPREME CDU Channel bandwidth 25 kHz
the standard manuals found on the documentation CD. It Size W x H x D: 255x140x84 [mm] Bit Rate 9600 bps
Gimbal Mount Intervals between position reports 1-180 s
A I S
is designed to give immediate access to essential Size W x H x D: 295x170x84 [mm] Modulation FM-GMSK/GFSK
information when executing an installation and a Transmitter 1
functionality test. Installation of the R5 SUPREME AIS Power Receivers 3
R5 SUPREME AIS Transponder Transceiver Sensitivity <-107 dBm
Transponder System should always be carefully Input 12/24 VDC (Max 30 VDC)
planned and executed by skilled personnel. Power Consumption: 20W (60W peak) Environmental data
R5 SUPREME CDU Protected environment (IEC 60945)
Input 12/24 VDC (Max 30 VDC) Operating temperature -15 °C to 55 °C
Please visit our web-site, saab.com, for the latest news Power Consumption: 13W
Compass safe distance
regarding this and other Saab products. AIS equipment is GPS Receiver (AIS internal) R5 SUPREME AIS Transponder
currently found under : saab.com/security/maritime-traffic- Receiver: 50 CH 65 cm to standard magnetic compass
Frequency: L1 (1575.42 MHz) 40 cm to steering magnetic compass
management/traffic-management/
S U P R E M E
Cables (recommended)
VHF and GPS RG214/U
Sensors e.g. Gyro RFE-HFI 2x2x0.75 mm2
Ethernet Cable CAT-5
R5 SUPREME AIS Installation Short
7000 118-363 C1
Instruction
INSTALLATION INITIAL SET UP
Connect the system as detailed below.
SYSTEM POWER UP
Connect External GNSS sensor, and if available Heading and Rate Of The R5 SUPREME AIS Transponder and CDU units will start to operate
Turn sensors, to the Junction box Sensor inputs. when power is applied. The system is fully operational within two minutes.
Connect External ECDIS to Junction box ECDIS port.
SETUP WIZARD
ARPA displays with AIS support may be connected to Junction box ECDIS The first time the R5 CDU is powered up, a setup wizard will be launched
or Pilot port. that will guide through the system setup
Note: An additional Pilot port for temporary access to AIS data is available Make sure the transponder has power and is connected by network to the
under the CDU front hatch. R5 CDU before continuing.
Connect the alarm relay to alarm system.
GPS
VHF
Set up the system as an AIS system and follow the set up guide. Make
Ethernet sure to configure network unique IP and LWE ID for the transponder and
CDU. Default AIS user password is user in lower case letters.
R5 Transponder
R5 Power Cable SYSTEM CONFIGURATION
R5 Signal Cable
R5 Signal Cable Set up the following parameters under: Main Menu Maintenance
External power Configuration AIS Ship Static
12-24 VDC R5 Power Cable
MMSI
IMO
Call Sign
R5 AIS
Junction Box
ECDIS/
ARPA Sensor 1
Sensor 3 Pilot Alarm
Ship Name
In/Out In/Out
In/Out In/Out Relay
Height over Keel
Long Sensor 2
In/Out
4xDigital
In/Out
External Switch
(Blue Sign / Silent)
Ship Type
Range
In/Out
If external system will be used for full AIS configuration including ship Unacknowledged active alarms Flashing RED
size/antenna configuration, Standard Mode is recommended unless the
external system integration has been verified with R5 specifically. Acknowledged active alarms Solid RED