Documente Academic
Documente Profesional
Documente Cultură
11S021-07
Table of Content
1 Product Precautions .................................................................................................................................................... 6
2 Warranty ........................................................................................................................................................................ 6
3 Specifications ............................................................................................................................................................... 7
3.1 STC-MC33USB / STC-MB33USB .............................................................................................................................. 7
Electronic Specifications / Mechanical Specifications / Environmental Specifications........................................ 7
Spectral Sensitivity Characteristics ..................................................................................................................... 8
3.2 STC-MB33USB-C....................................................................................................................................................... 9
Electronic Specifications / Mechanical Specifications / Environmental Specifications........................................ 9
Spectral Sensitivity Characteristics ................................................................................................................... 10
3.3 STC-MC83USB / STC-MB83USB .............................................................................................................................11
Electronic Specifications / Mechanical Specifications / Environmental Specifications.......................................11
Spectral Sensitivity Characteristics ................................................................................................................... 12
3.4 STC-MC133USB / STC-MB133USB ........................................................................................................................ 13
Electronic Specifications / Mechanical Specifications / Environmental Specifications...................................... 13
Spectral Sensitivity Characteristics ................................................................................................................... 14
3.5 STC-MC152USB / STC-MB152USB ........................................................................................................................ 15
Electronic Specifications / Mechanical Specifications / Environmental Specifications...................................... 15
Spectral Sensitivity Characteristics ................................................................................................................... 16
3.6 STC-MC202USB / STC-MB202USB ........................................................................................................................ 17
Electronic Specifications / Mechanical Specifications / Environmental Specifications...................................... 17
Spectral Sensitivity Characteristics ................................................................................................................... 18
4 Connector Specifications .......................................................................................................................................... 19
5 Input / Output signals specifications ....................................................................................................................... 20
5.1 Input signals specifications ....................................................................................................................................... 20
Function for the input signals ............................................................................................................................ 20
Characteristics of the input signals ................................................................................................................... 20
Input signal circuits ............................................................................................................................................ 21
5.2 Output signals specifications .................................................................................................................................... 22
Function for the output signals .......................................................................................................................... 22
Characteristics of the output signals ................................................................................................................. 22
Output signal circuits ......................................................................................................................................... 23
6 Dimensions ................................................................................................................................................................. 24
6.1 STC-MB33USB / STC-MC33USB / STC-MB83USB / STC-MC83USB / STC-MB133USB / STC-MC133USB ...... 24
6.2 STC-MB33USB / STC-MC33USB / STC-MB83USB / STC-MC83USB / STC-MB133USB / STC-MC133USB
(with tripod) ............................................................................................................................................................... 25
6.3 STC-MB152USB / STC-MC152USB / STC-MB202USB / STC-MC202USB / STC-MB33USB-C........................... 26
6.4 STC-MB152USB / STC-MC152USB / STC-MB202USB / STC-MC202USB / STC-MB33USB-C (with tripod) ....... 27
6.5 Tripod ........................................................................................................................................................................ 28
7 Revision History ......................................................................................................................................................... 29
2. Disable the power save mode with the Sentech PC power management software.
The power save mode can disable with the Sentech PC power management software “StPowerCtrl”.
Please contact to the Sales representative about this software.
The power consumption and the heat of the PC are increased when disable the power save mode. Please understand
and accept this before disable the power save mode.
3. Change the camera clock from “Normal” to “1/2” or “1/4”. (Reduce the frame rate)
In this “Precautions for safe use”, notes divides into “Warning” and “Caution” to use the camera safety and prevent to
harm and damage.
About Graphic
symbols This symbol shows general prohibition.
[Environment / condition]
Warning
Do not use flammable or explosiveness Do not use for “safety for human body” related
atmospheres. usage.
This will cause of personal injury or fire. This camera is designed for use “do not harm
human body immediately” if by any chance the
camera has malfunction.
Caution
Use and store under specified environmental
conditions (Vibration, shock, temperature,
humidity) in the specifications for this camera.
This will cause of fire or damage the camera.
Warning
Do not use with out of power voltage range Do not wrong wiring.
that is specified in the specifications for this This will cause of fire or malfunction.
camera.
This will cause of fire, electrification or
malfunction.
Caution
Do not grounding DC power (+) of all devices It is necessary to wiring and mounting that is
that are connect to the camera. specified in the specifications for this camera.
The camera housing is connecting to 0 V line of This will cause of fire or malfunction.
camera inside circuit.
There is a risk of short circuit between camera
inside ciurcuit and frame ground.
This will cause of malfunction.
It is necessary to wiring with turn off the camera. It is necessary to mounting the camera without
This will cause of electrification or malfunction. stress for the cable.
This will case of electrification or fire.
[Usage instruction]
Warning
Do not touch the terminal and PCB board Do not put combustibles near the camera.
While turn on the camera. This will cause of fire.
This will cause of electrification or accident
caused by malfunction.
Do not use without usage that is specified in Do not push metals including screw driver into
the specifications for this camera. radiation holes.
This will cause of personal injury or malfunction. This will cause of electrification or malfunction.
Caution
Do not push contamination into opening of Do not block the radiation holes.
the camera. This will cause of fire due to increase the
This will cause of electrification or malfunction. camera inside temperature.
[Maintenance]
Caution
Do not disassemble or repair the camera. It is turn off the camera when maintaining or
This will cause of fire, electrification or inspecting the camera.
malfunction. This will cause of electrification.
[Disposal]
Caution
It is necessary to dispose as industrial waste.
]
1 Product Precautions
Do not give shock to the camera.
Do not haul or damage the camera cable.
Do not wrap the camera with any material while using the camera. This will cause the internal camera
temperature to increase.
When the camera moving or using the place that temperature difference is extreme, countermeasure for
dew condensation (heat removal / cold removal) is necessary.
While the camera is not using, keep the lens cap on the camera to prevent dust or contamination from getting
in the sensor or filter and scratching or damaging it.
Do not keep the camera under the following conditions.
・ In wet, moist, high humidity or dusty place
・ Under direct sunlight
・ In extreme high or low temperature place
・ Near an object that releases a strong magnetic or electric filed
・ Place with strong vibrations
Apply the power that satisfies the specified in specifications for the camera.
The defective pixels may appear due to the sensor characteristics.
Use below recommend materials (or equivalent materials) to clean the surface of glass.
・ Air dust: Non Freon air duster (NAKABAYASHI Co., LTD.)
・ Alcohol: Propan-2-ol (SAN’EI KAKO Co., LTD.)
・ Non-woven: nikowipe clean room (NKB)
Use a soft cloth to clean the camera.
2 Warranty
■Warranty period
One year after delivery (However, the camera had malfunction with camera uses correctly)
In below case for a fee even within warranty period.
・The malfunction caused by incorrect usage, incorrect modify or repair.
・The malfunction caused by external shock including the camera dropping after delivery the camera.
・The malfunction caused by fire, earthquake, flood disaster, thunderbolt struck, other natural disaster or
wrong voltage.
■Warranty coverage
Exchange or repair the malfunction camera if the malfunction is occurred by our responsibility.
“Warranty” mean is warranty for the delivered camera itself. Please accept the induction damage by the
camera malfunction is not included.
3 Specifications
(Caution)
Please DO NOT connects or disconnect any USB devices including USB memory while use this USB camera.
Its possibility to the USB camera DOES NOT recognize after connect or disconnect USB devices.
1
G
R
0.8
B
Relative Response
0.6
IR cut filter
0.4
0.2
0
400 500 600 700
Wave length [nm]
STC-MB33USB
0.8
Relative Response
0.6
0.4
0.2
0
400 500 600 700 800 900 1000
Wave length [nm]
3.2 STC-MB33USB-C
Product STC-MB33USB
Electronic Image Sensor 1/3" interline VGA monochrome progressive CCD:
Specifications ICX424AL (Sony)
Total picture elements 692 (H) x 504 (V)
Effective picture elements 659 (H) x 494 (V)
Chip size 5.79 (H) x 4.89 (V) mm
Cell size 7.40 (H) x 7.40 (V) μm
Scanning system Progressive
Resolution 640 (H) x 480 (V) (Full scanning)
640 (H) x 224 (V) (1/2 partial scanning)
640 (H) x 80 (V) (1/4 partial scanning)
Scanning methods Full scanning, 1/1 partial scanning, 1/2 partial scanning, 1/4 partial scanning,
Variable partial scanning,
Binning scanning, Binning 1/1 partial scanning, Binning 1/2 partial scanning, Binning 1/4 partial scanning,
Binning variable partial scanning
Maximum Full scanning 59.94 fps (Normal) / 29.97 fps (1/2 clock) / 14.98 fps (1/4 clock) / 89.91 fps (3/2 clock)
framer rate 1/2 partial scanning 120.11 fps (Normal) / 60.05 fps (1/2 clock) / 30.02 fps (1/4 clock) / 180.165 fps (3/2 clock)
1/4 partial scanning 240.22 fps (Normal) / 120.11 fps (1/2 clock) / 60.055 fps (1/4 clock) / 360.33 fps (3/2 clock)
Pixel frequency 24.5454 MHz (Normal) / 12.2727 MHz (1/2 clock) / 6.13635 MHz (1/4 clock) / 36.818 MHz (3/2 clock)
Video output 8bit / 10bit / 12bit
Minimum scene illumination 0.17 Lux at F1.2
Sync. System Internal
Electronic shutter Auto / Manual (software selectable)
Normal 1/100,000 to 1/59,94 seconds
1/2 clock 1/100,000 to 1/29.97 seconds
1/4 clock 1/100,000 to 1/14.99 seconds
3/2 clock 1/100,000 to 1/89.91 seconds
Gain Auto / Manual (software selectable)
Gamma Manual (software selectable)
White balance -
Trigger mode Free-run / Edge preset trigger / Pulse width trigger / Start & stop trigger (software selectable)
(Hardware trigger and Software tigger are available)
Input/output USB2.0 High speed
Power Input voltage +5 V through USB connector (+4.4 to +5.25V)
Consumption Less than 420 mA
Mechanical Dimensions 28 (W) x 28 (H) x 42 (D) mm (excluding the connector)
Specifications Lens mount C mount
Weight Approximately 45g
Interface connector USB: mini-B USB connector
IO signal: 6pin connector (HR10A-7R-6PB or equivalent)
Environmental Operational temperature 0 to 40 deg. C
Specifications Storage temperature -30 to 65 deg. C
Vibration 20Hz to 200Hz to 20Hz (5min./cycle), acccelaration 10G, 3 directions 30 min. each
Shock Accelaration 70G, half amplitude 6ms, 3 directions 3 times each
Standard compliancy EMS:EN61000-6-2, EMI:EN61000-6-3 (Class B)
RoHS RoHS compliance
(Caution)
Please DO NOT connects or disconnect any USB devices including USB memory while use this USB camera.
Its possibility to the USB camera DOES NOT recognize after connect or disconnect USB devices.
STC-MB33USB-C
0.8
Relative Response
0.6
0.4
0.2
0
400 500 600 700 800 900 1000
Wave length [nm]
(Caution)
Please DO NOT connects or disconnect any USB devices including USB memory while use this USB camera.
Its possibility to the USB camera DOES NOT recognize after connect or disconnect USB devices.
G
R
0.8
B
Relative Response
0.6
IR cut filter
0.4
0.2
0
400 500 600 700
Wave length [nm]
STC-MB83USB
0.8
Relative Response
0.6
0.4
0.2
0
400 500 600 700 800 900 1000
Wave length [nm]
(Caution)
Please DO NOT connects or disconnect any USB devices including USB memory while use this USB camera.
Its possibility to the USB camera DOES NOT recognize after connect or disconnect USB devices.
1
R
0.8
G
Relative Response
B
0.6
IR cut filter
0.4
0.2
0
400 500 600 700
Wave length [nm]
STC-MB133USB
0.8
Relative Response
0.6
0.4
0.2
0
400 500 600 700 800 900 1000
Wave length [nm]
(Caution)
Please DO NOT connects or disconnect any USB devices including USB memory while use this USB camera.
Its possibility to the USB camera DOES NOT recognize after connect or disconnect USB devices.
G
R
0.8
B
Relative Response
0.6
IR cut filter
0.4
0.2
0
400 500 600 700
Wave length [nm]
STC-MB152USB
0.8
Relative Response
0.6
0.4
0.2
0
400 500 600 700 800 900 1000
Wave length [nm]
(Caution)
Please DO NOT connects or disconnect any USB devices including USB memory while use this USB camera.
Its possibility to the USB camera DOES NOT recognize after connect or disconnect USB devices.
G
R
0.8
B
Relative Response
0.6
IR cut filter
0.4
0.2
0
400 500 600 700
Wave length [nm]
STC-MB202USB
0.8
Relative Response
0.6
0.4
0.2
0
400 500 600 700 800 900 1000
Wave length [nm]
4 Connector Specifications
1. USB connector: Mini B USB type
Pin assignment
Input and output signals are isolated. [Connector on the rear panel]
The polarity for the trigger signal input, the read out signal input and the sub trigger signal input can be
selectable.
(Recommend: Use with the negative polarity for reduces the timing delay by the photo-coupler)
Input signal duration: The signal duration should be longer than “Tf + Tr”.
Please check “Input signal response timings” for Tf and Tr.
Ts Td
IO_VCC
USER INPUT
IO_GND
3.3V
90%
Camera inside
10%
0V
Tf Tr
IO_VCC
3.3[V] 5.0[V] 12[V] 24[V]
Td 35.2 [us] 38.2 [us] 39.6 [us] 39.6 [us]
Example circuits 1
CAMERA
CAM_VCC IO_VCC
INPUT
6pin
4pin or 5pin
OPTO ISOLATOR
Renesas: PS2915-1
IO_GND
Example circuits 2
CAMERA
CAM_VCC IO_VCC
INPUT
6pin
IO_VCC
USER_INPUT
4pin or 5pin
OPTO ISOLATOR
Renesas: PS2915-1
IO_GND
The polarity for the trigger signal, the exposure end signal, the CCD read out end signal, the strobe signal
(time setting) and the strobe signal (exposure time) can be selectable.
(Recommend: Use with the negative polarity for reduces the timing delay by the photo-coupler)
Output signal duration: The signal duration should be longer than “Tf + Tr”.
Please check “Output signal response timings” for Tf and Tr.
The signal duration can adjust by the software.
3.3V
Camera inside
0V
IO_VCC
90%
USER OUTPUT
10%
IO_GND
Tf Tr
IO_VCC
3.3[V] 5.0[V] 12[V] 24[V]
Td 41.6 [us] 56.8 [us] 49.6 [us] 44.8 [us]
Example circuits 1
CAMERA
6pin IO_VCC
USER_Pull-Up
5.6k Ohm
OUTPUT
1pin
OPTO ISOLATOR
Renesas: PS2915-1
IO_GND
6 Dimensions
6.1 STC-MB33USB / STC-MC33USB / STC-MB83USB / STC-MC83USB / STC-MB133USB /
STC-MC133USB
Unit: mm
Unit: mm
Unit: mm
Unit: mm
6.5 Tripod
12
9.5 9.5
6.5
(10.5)
(10.5)
(R13.8)
Unit: mm
7 Revision History