Documente Academic
Documente Profesional
Documente Cultură
WPPM-1212-M2AF
WPPM-1212-M3BF
Specifications
System shall be plumbed using Watts WaterPEX cross-linked polyethylene pipe. All joints shall be made using Watts brass CrimpRing and/or poly-alloy CrimpRing fittings using either the Watts copper CrimpRing or stainless steel CinchClamp crimping methods as outlined in the Watts WaterPEX Installation Guidelines.
WPPM-12-M4AB
Installation Note
CrimpRing Manifold must be installed in accordance with all Watts WaterPEX installation procedures, including information provided in WaterPEX installation manual and guidelines.
Approvals
WPPM-12-M3BB
Manufactured in accordance with American Society for Testing and Materials (ASTM) F-877 and F-2159 Listed by the National Sanitation Foundation to NSF Standards 14 and 61 for use in potable water systems Listed by IAPMO to be in compliance with the Uniform Plumbing Code Labeled B137.5 which indicates that it is compliant to the CSA Standard B137.5 Manufactured from Acudel engineered thermoplastic resin.
* The wetted surface of this product contacted by consumable water contains less than one quarter of one percent (0.25%) of lead by weight. ** Note: Watts WaterPEX CinchClamp should not be used with wrot copper PEX fittings. Acudel is a registered trademark of Solvay Advanced Polymers.
Caution: The polyphenylsulfone material used in the Poly-Alloy CrimpRing manifolds can be compromised by exposure to volatile organic compounds (VOCs) and caustic chemicals which would include exposure to the following products: Pipe Dopes and thread sealants, insect sprays, lubricants, cleaners, paints, bleaches, acids, solder fluxes, plastic piping primers and cements, oxidizing agents, alkaline solutions, thinners, fuels, oil based caulks, hydrocarbons, spray foam insulations. CAUTION! f connections must be made in temperatures below 30F, I caution must be taken to allow the WaterPEX to form a proper seal against the barb in order to avoid subsequent water damage. Apply the connection slowly to ensure the PEX material conforms to the barb.
Watts product specifications in U.S. customary units and metric are approximate and are provided for reference only. For precise measurements, please contact Watts Technical Service. Watts reserves the right to change or modify product design, construction, specifications, or materials without prior notice and without incurring any obligation to make such changes and modifications on Watts products previously or subsequently sold.
Dimensions Weights
Model in Inlet mm. in OUTLET mm. . in mm PORTS PKG WEIGHT
Qty/Configuration
lbs.
kgs.
20 20 20 25 25 25 20 20 20 25 20 20
34 34 34 1
34 34 34 34
12 12 12 12
12 12 12 12
15 15 15 15 15 15 15 15 15 15 15 15
2/One Side 3/One Side 4/One Side 4/One Side 6/One Side 6/One Side 3/Offset 4/Offset 4/One Side 6/One Side 3/Offset 4/Offset
.04 .05 .06 .1 .14 .15 .04 .04 .06 .14 .04 .04
.018 .022 .027 .045 .063 .068 .018 .018 .027 .063 .018 .018
12 12
USA: No. Andover, MA Tel. (978) 688-1811 Fax: (978) 794-1848 www.watts.com Canada: Burlington, ONT. Tel. (905) 332-4090 Fax: (905) 332-7068 www.wattscanada.ca
ES-WP-PACrimpManifolds 1102
2011 Watts