Sunteți pe pagina 1din 2

Index

K-TRON SODER Product Specification


K-PH-MV-KT35
Twin-Screw Pharma Feeder

Application
Volumetric feeding of free flowing to very hard flowing powders (e.g. lumpy,
moist or bridge building materials), especially in pharma applications.
The feeder can be upgraded to a loss-in-weight feeder system at any time.

Design
Twin-screw feeder with interchangeable feeding tools. All parts in contact with
the material being fed are stainless steel. Feeding equipment is easy to
dismantle. The horizontal agitator gently moves bulk material to the large throat
and then into the discharge screws.

Controller: (see separate data sheet)


The K-PH-MV-KT35 uses the microprocessor based DigiDrive DC closed
loop motor speed controller. The pulse width modulation features of the
DigiDrive controller allow the motor to run efficiently at all speeds, increasing
motor life and providing control accuracy to within ±1 RPM. The simple user
friendly interface allows entry and display of feeder output in selectable
engineering units. Alarms are programmable. Setpoints can be stored.
As an alternative the drive can be a AC-motor. Control via frequency K-PH-MV-KT35
converter. with vertical outlet and optional housing
This equipment conforms to CE standards regarding EMC and safety. for motor and gearbox

Feeder Screws and Feed Rates


Actual feeder screws will be determined by the material being fed.
Speed range (rpm) and the type of gear are determined by the feed rate.
Feeder screws are easily interchangeable.

Twin Twin
Type concave Speed Gearbox
Pitch auger
of drive screws range type
screws

long
pitch
dm3/h ft3/h dm3/h ft3/h RPM
16 - 1611 0.57 - 56.9 17 - 1673 0.6 - 59.1 6 - 620 A
7.7 - 772 0.3 - 27.3 8.0 - 807 0.3 - 28.5 3 - 297 B
3.3 - 334 0.1 - 11.8 3.5 - 347 0.1 - 12.3 1.3 - 128 C

113 - 1965 4 - 69.4 117 - 2041 4.1 - 72.1 43 - 756 A


~ 54 - 942 1.9 - 33.3 56 - 978 2 - 34.5 21 - 362 B
23 - 407 0.8 - 14.4 24 - 423 0.9 - 14.9 9 - 157 C

short
pitch
dm3/h ft3/h dm3/h ft3/h RPM
5.6 - 558 0.2 - 19.7 5.9 - 589 0.2 - 20.1 6 - 620 A
2.7 - 267 0.09 - 9.4 2.8 - 282 0.1 - 10 3 - 297 B
1.2 - 116 0.04 - 4.1 1.2 - 122 0.04 - 4.3 1.3 - 128 C
Max. feed rates are based on a max.
motor speed of 2000 RPM with DC-
39 - 680 1.4 - 24 41 - 718 1.5 - 25.3 43 - 756 A
motor. The feed rate indications are
~ 19 - 326 0.8 - 11.5 20 - 344 0.7 - 12.1 21 - 362 B approximate values.
8.1 - 141 0.3 - 5 8.5 - 149 0.3 - 5.3 9 - 157 C The gravimetric feed rate can be
calculated from the bulk density.
Speed controller with DC-motor. Speed control range 1 : 100
~ Frequency inverter. Speed control range 1 : 17 (5 - 87 Hz)

Rev. 0 S-010602-en
04.2002
CD06 Doc# 0290005304 Page 1 of 2
Index

K-TRON SODER Product Specification


K-PH-MV-KT35
Twin-Screw Pharma Feeder

Configuration Technical Data


Standard
Hopper content: 15 dm3 (0.5 ft3)
Total weight (Mot. 0.45 kW): 25 kg (55 lb)
DigiDrive Frequency (without housing)
115-240 V inverter Materials:
50/60 Hz 220 V Parts in contact
with bulk material: stainless steel,
(DIN 1.4404 / 1.4435,
Range Range AISI 316L)
1 : 100 1 : 17 Seals: PTFE / silicon rubber
Painting of motor
and gearbox: light grey RAL 7035
Gearbox

A B C A B C
Options
1 Housing for motor and gearbox
Motor drive 2 Wall mounting device
200 V 3 x 220/127 V 3 x 220/127 V 3 Air purge nozzles
0.55 kW
4 Pre-reducer 4 : 1
0.45 kW 0.55 kW EEx de IIC T4
IP 55 IP 55 IP 55 5 Base hoppers (see table below)

Dimensions mm (in) shown with vertical outlet


Ø 254 (10)
Ø 220 (8.7)
31 (1.2)

488 (19.2)

Safety screen

Housing for motor and


285 (11.2)

15 dm3 10 dm3
0.5 ft3
0.33 ft3 gearbox = optional
325 (12.8)
291 (11.5)

a
120 (4.7)

DIN DN 100 Ø 100


(3.9)
116 (4.6) 326 (12.8) 415 (16.3)

6 (0.2) Base hoppers (see also sheet I-050101)


H D1 X
dm3(ft3)
mm(in.) mm(in.) mm(in.) D1
a) Horizontal outlet
270 (10.6)

50 615 400 90
Ø 78 (3.1)

39 (1.5)

(1.77) (24.2) (15.8) (3.54) X


H

80 869 400 90
(2.83) (34.2) (15.8) (3.54)
64 (2.5) 30 (1.2)
166 (6.5)
110 922 600 190
(3.9) (36.3) (23.6) (7.48)

K-TRON AMERICA K-TRON (Schweiz) AG For the addresses of all


Routes 55 & 553 Industrie Lenzhard K-TRON Companies
Pitman, NJ 08071 USA CH-5702 Niederlenz see info sheet I-000001
Tel: (856) 589-0500 Tel: 062 885 71 71
Fax: (856) 589-8113 Fax: 062 885 71 80
e-mail: ka@ktron.com e-mail ks@ktron.com
Rev. 0 S-010602-en
CD 06
Internet: www.ktron.com Page 2 of 2

S-ar putea să vă placă și