Documente Academic
Documente Profesional
Documente Cultură
Phone
Fax
E-mail
URL
Plant
Tokyo 108-8586, Japan
: +81 (0)3-3448-5850
: +81 (0)3-3447-7637
: ntt@ikonet.co.jp
: http://www.ikont.co.jp/eg/
: Gifu, Kamakura
• The specifications and dimensions of products in this catalog are subject to change without prior notice. • When these products are exported, the
exporter should confirm a forwarding country and a use, and, in case of falling under the customer's requirements, take necessary procedures such
as export permission application. • Although all data in this catalog has been carefully compiled to make the information as complete as possible,
NIPPON THOMPSON CO., LTD. shall not be liable for any damages whatsoever, direct or indirect, based upon any information in this catalog.
Gentle to The Earth NIPPON THOMPSON CO., LTD. makes no warranty, either express or impiled, including the impiled warranty of merchantability or fitness for a ISO 9001 & 14001 Quality system registration certificate
particular purpose. • Reproduction and conversion without permission are prohibited.
Slim design and easy mounting can reduce the size and weight of your equipment.
CRBTF Structure and Features What are Crossed Roller Bearings?
Inner ring
IKO Crossed Roller Bearings are compact bearings with their
Outer ring Roller
Make your equipment more compact rollers alternately crossed at right angles to each other
between inner and outer rings. The orthogonal array of the
with this super slim design! rollers allows a single bearing to handle complex loads
Mounting Holed Type Super Slim Crossed Roller Bearings have simultaneously from any direction, making mounting possible
Outer ring
an ultra-slim 5 mm bearing width, made possible thanks to without worrying about load direction.
IKO's technological expertise in miniature bearing production.
Roller
Mounting
5
Separator
· The shoulder height diameters (da and Da) which are related to
Inner ring mounting must meet the values shown in the dimension tables. da
Easy bolt-on mounting eliminates complex
mounting procedures. · When used with a housing, it is recommended to use a slight
interference fit adjusted to the actual measured dimensions of
Mounting hole
Mounting Holed Type Super Slim Crossed Roller Bearings can be the outer and inner ring. In addition, the depth of the housing
mounted directly to the mounting surface. No housing or pressure bore is recommended to be equal to or larger than the bearing
plate required. width.
Super Slim Type Crossed Roller Bearing Mounting Holed Type Super Slim
· Mounting Holed Type Super Slim Crossed Roller Bearings have
Mounting Method Crossed Roller Bearing Mounting Method Da
a plug hole for inserting cylindrical rollers. When mounting the
Until now... bearings, position the plug away from the maximum load. The
Housing and Tighten the fixing screws (M2.5 x 0.4) at 0.58 N·m torque.
pressure plates plug is located by the pin on the side.
were required.
High Low High Low High Low Maximum Maximum Min. Maximum
10 0 -8 0 -11 0 -75 13 20 0 15
Da
da
PCD 2
PCD1
r
30 0 -10 0 -13 0 -75 15 25 0 15
Table 1. Dimensions
Shaft diameter Identification number Mass Boundary dimensions mm Mounting holes mm Mounting dimensions mm Basic dynamic load rating Basic static load rating
(Ref.) C C0
Inner ring Outer ring
( )
1
rmin
mm g d D B PCD1 PCD 2 da Da N N
Mounting holes Mounting holes
6-φ 2.9 through
10 CRBTF 105 AT 46 10 43 5 0.15 16 6-M2.5 through 35 φ5.5 Counterbore depth 2.8 21.5 28 1 500 1 410
Note (1)
Minimum allowable single value of chamfer dimension r. Remarks 1. No oil hole is provided. 2. Provided with pre-packed grease. 1N ≈ 0.102 kgf