Documente Academic
Documente Profesional
Documente Cultură
SC2X6 SRS
SPR03 SPR02X
P46R
D2.2-S-P
AM17XL/R
AT119
SS3X3
ST69-00
Note: P46R ball should be placed O ST69-15 and ST69-25 screw
between SRS screw and ST69-00 screw. are .
Attention! fter installation of SPR02X rotate the complete D2.2-S-P damper within AM17XR/L
until the maximum up travel is reached ecure SC2X6 screw in the AM17X/RL after that.
SPR02X AM17X/RL !!!
SPR01
STEPS 6
FINISHED
Assemble 2 Right hocks
and 2 Left hocks.
Note:
Initial position of ST69-0 crew is ~0,6mm.
8
STEP 7
Note:C01B-X-MM2 Carbon Lower Deck is used in A800MMX kit.
C01B-X-MMA Alloy Lower Deck is used in A800MMXA kit.
D SF3X6
ST-A x4
ST-A x4 AT21ST-A
SH1.75 x4
FRONT
SH1.75 x4
SF3X6 x4
SF3X6 x4
REAR
SF3X6 M3x6 Flat Head Screw x8 P03 rm Ball Cap x8
STEP 8
SF3X5 M3x6 Flat Head Screw x14 ST24 4,8mm Ball Stud x2
Install two ST24 all Studs
on two rear AM78X1 Bulkheads. AM177 Motor Mount x1
AM78X1 Bulkhead x4
P56 Antenna Holder x1
AM78X1 x2
ST24 x2 SF3X5
REAR FRONT
5 4 3 2 1
Motor mount screws designation for setup sheet
AM78X1 x2
AM177 AM78X1 x2
P56
SF3X5 x4
SF3X5 x6
SF3X5 x4
9
STEP 9 STEP 10
G07 G07 G08
WA02 P39 WA02
G07
G07
WA02 ST31-1
WA02
G08
P46R
P46R
ST31-1
WA03
WA03 B85
B85 OR05
OR05
SC2X4 x3
hread Lock
AT123B
P138 B106RS
OR05M
OR06
OR13 ST23X
OR13
ttention! PIN02
SC X4
t B106RS MR106RS Bearing x2 AT123B GD2B Case1 x1
P 38 AT124B
AT124B GD2B Case2 x1
hread Lock B106RS B85 MR85 Bearing x2 P138 38T Pulley x1
ST23X IRJ Outdrive x2
OR05 O-Ring x2 ST31-1 GD2 Output Axle x2
P39 GD2 Cross Pin x1
STEP 11
OR06 O-Ring x2 OR13 13 mm -Ring x1
G07 GD2 Satellite Gear x4
P46R Piston x2 G08 GD2 Bevel Gear x1
PIN02 1,5x5,8 Pin x2 WA02 3.5x9.5x0.2 Washe x4
SC2X4 M2x4 Cap Head screw x3 WA03 5x15.5x0.3 Washer x2
Fill with desirable silicone oil (not included).
Screw AT123B GD2B Case with 10mm wrench slowly. STEP 12
The excessive oil will go out through the ST31-1 axial hole. ST23X
PIN02
OR06
P46R
B106RS
Diff Oil
oil level
SF3X8
AT03BX B106RS
ST37X
SF3X8
P138S SB3X5 x3
STEP 13 FINISHED
ttention!
SC3X5
t P 38S 03BX
hread Lock P 38S
P110 P110
P110
P110
11
STEP 15 STEP 16
Attention! Note orientation
of this chamfer on DT22.
DT22
SB3X8 AT120-5
B84RS
AM88L AT62-5M
AT120XB
SB3X8
B106RS
AM88R
REAR Note: AT120XB is fully factory
assembled for your kit.
AM19-FX x2
SB3X5 x4
AT120XB
SB25X8
AM19-FX x2
BEL351B
BEL351B
Rear belt
12
STEP 18
SB3X5AL
ST24
SH0.5
SB3X10
ST24
AT21ST-A x2
SH1.0
Use SB3X5AL s re as a steering
imiter (usually on carpet tracks).
AM180 SF3X5 x2
ST118
SF3X5 x2
AM180 Be ran position an e
changed via shi t ng of ST118 Axle ST118
ithin 1mm range or a justing of
the Ackermann setting. We recommend the rearward
AM 52 position for carpet and the forward position for asphalt tracks.
Attention!
Tighten SB3X8 screws of
FRONT
AM88L/R with 2mm ball
hex driver after tightening
of SF3X10 screws.
SF3X10
REAR SF3X10
REAR
13
STEP 20 Note: C127S Top Decks are used in A800MMXA kit.
SB3X5 x4 FRONT
C127 Top Decks are used in A800MMX kit.
ST019 C127 ST019
M05C ST019 x2
SB3X5 x4
SB3X6 x2 C127
A
B
op decks C
holes designation
for setup sheet
D
E
F
ST019
recess REAR
STEP 21 ST24 4
ST24 4
SH1.0 x4
SH1.0 x8
SH1.75 x4
SH1.75 x4
REAR FRONT
P07
P07
14