Documente Academic
Documente Profesional
Documente Cultură
Lucent Technologies’ Matched Cladding Lucent Technologies was one of the first
Single Mode Fiber sets the standard for fiber manufacturers to specify maximum
optical fiber performance. The exacting limits on polarization mode dispersion
specifications and quality control of (PMD). PMD can affect performance in
Lucent Technologies allows you to take digital systems at very high bit rates and
advantage of the full capability of single in high capacity analog systems.
mode fiber. Before you purchase any
Excellent control of the geometrical
matched clad fiber, evaluate our fiber.
properties of this fiber allows low loss
Matched Cladding Single Mode fiber splicing with either single fiber or mass
consists of a germanium-doped core fusion techniques. It can be readily
surrounded by a silica cladding. The spliced to most other manufacturers’
nominal mode field diameter is 9.3 µm, matched clad fibers or to Lucent
making this fiber compatible with most Technologies’ Depressed Clad fiber with
single mode fibers. Although character- extremely low splice loss, increasing
istics are optimized for operation in installation efficiency and maintaining
the 1310 nm region, where dispersion system performance.
is lowest, operation in the lowest loss
D-LUX® Coating for Long-term
1550 nm region is also possible.
Reliability
Since its introduction in 1989, D-LUX
coating has been recognized as a
superior coating. Recent enhancements
such as increased delamination resistance
and compatibility with additional filling
compound materials have been made to
make D-LUX coating even better.
All Lucent Technologies’ fiber features
the D-LUX coating system. A dual layer
of UV-cured acrylate material is applied
125 MICRON directly to the glass surface. This
CLADDING mechanically strippable coating material
has a nominal diameter of 245 µm. The
benefits of D-LUX coating include:
• Cushions fiber against microbending
loss
• Provides abrasion and cut-through
resistance for protection and ease-of-
use
8.3 MICRON CORE • Extremely stable over wide range of
environmental conditions for long-term
Cross section of 8.3 µm single mode fiber
reliability
• Resistant to color change for easy fiber
identification after aging
refractive index difference 0.4
0.3
0.2
0.1
0.0
-0.1
-15 -10 -5 0 5 10 15
radius (microns)
SPECIFICATIONS
2
dB/km
Wavelength dB/km
1.0 µm 1.15
1
1.30 µm 0.35
1.31 µm 0.34
1.38 µm 0.50 0
1.55 µm 0.19 0.90 1.10 1.30 1.50
WAVELENGTH (µm)
The maximum attenuation (loss) in dB/km may be 2.5%/min. Med = 706 ksi.m - 100
95
specified within the ranges indicated in the table below: 90
80
Wavelength (nm) Maximum Attenuation (dB/km) 70
60
1310 0.35 - 0.40 50
40
1550 0.21 - 0.30 30
% FAILURE
20
Attenuation vs.Wavelength:
10
The maximum attenuation in the wavelength region
from 1285 nm to 1330 nm is no more than 0.10 dB/km 5
greater than the attenuation at 1310 nm.
The maximum attenuation in the wavelength region
from 1525 nm to 1575 nm is no more than 0.05 dB/km 1
greater than the attenuation at 1550 nm.
50 100 200 400 600 800
Strength (kpsi)
Attenuation at Water Peak: Gauge Length is 20 meters
Point Discontinuities:
There are no attenuation discontinuities greater than 0.1
dB at 1310 nm or 1550 nm. OTHER PERFORMANCE CHARACTERIZATIONS
ENVIRONMENTAL CHARACTERISTICS
ORDERING INFORMATION
Fiber Type: Lucent Technologies Matched Cladding
Single Mode Fiber
Coating: D-LUX® Coating Series
Attenuation: 1310 nm maximum dB/km
1550 nm maximum dB/km
Length meters
Proof Test Level kpsi
Number/Color of Spools # spools
ORDERING INFORMATION
Lucent Technologies
Marketing
4553FS - Issue 2 - LLC - 6/96