Sunteți pe pagina 1din 8

PAINTING CYCLE

Client ENPPI Engineering for the Petroleum


and Process Industries

P.O. Number 3522-200-239-01-47

Name of Project ASSIL AND KARAM GAS DEVELOPMENT PROJECT

Project Number 3522-200

Document Title
Painting cycle applicable on carbon steel material with operating
temperature -35°C to 120°C according to
Spec. AKA-001-RA-7754-00001 Rev. 1 System LC1-N
(Applicable only for valves)
Document Number PC 3150

2
Revisionato come da commenti del cliente/ Q.C. Q.M.
1 29.01.2013
Revised as per client comments S Frazzi D.Morelli
Emissione per approvazione/ Q.C. Q.M.
0 17.01.2013
Issue for approval S Frazzi D.Morelli
Rev. Data/Date Descrizione/ Preparato/ Approvato
Description Prepared: /Approved :

PC 3150 Rev. 0 Page. 1 of 8


Doc. No. PC 3150
CICLO DI VERNICIATURA
Painting Cycle Sh 1 of 1

PROPRIETA’ TECNICHE
See attached technical sheet
Technical Properties

PREPARAZIONE SUPERFICIE Blast clean using dry grit type abrasive according to SA 2.5 (ISO 8501-1)
Surface preparation to achieve a surface profile of 30 ÷ 50 µm

DESCRIZIONE DEL CICLO / Cycle description


COAT PAINTING TYPE PRODUCT SUPPLIER M.D.F.T. (µm)
Primer Two pack, zinc rich epoxy primer Carbozinc 858 CARBOLINE 75 µm ÷ 100 µm
Two component, high build, low temperature
Intermediate Carbomastic 15 LT CARBOLINE 150 µm ÷ 175 µm
modified aluminium epoxy mastic
Top coat Acrylic aliphatic polyurethane Carbothane 134 HP CARBOLINE 75 µm ÷ 100 µm

TOTAL MINIMUM DRY FILM THICKNESS (µm) 300 µm ÷ 375 µm

FINAL COLOUR RAL 7035 LIGHT GREY

CONTROLLI RICHIESTI CHE DOVRANNO ESSERE ESEGUTI DA UN INSPETTORE NACE II LIVELLO/


Inspection requirements to be carried out by NACE inspector II level
CONTROLLO VISIVO PULIZIA SUPERFICIE DOPO SABBIATURA IN ACCORDO ALLA ISO 8501-1
Steel surface cleanliness visual check after blasting operation according to ISO 8501-1
CONTROLLO PULIZIA SUPERFICIE (PRESENZA DI POLVERE) DOPO SABBIATURA IN ACCORDO ALLA ISO 8502-3
(METODO ADESIVO SENSIBILE A PRESSIONE)
Steel surface cleanliness check (dust presence) after blasting operation according to ISO 8502-3(pressure sensitive tape method)
CONTROLLO PROFILO DELLA SUPERFICIE DOPO SABBIATURA IN ACCORDO ALLA ISO 8503 ; IL PROFILO DELLA SUPERFICIE DOVRÀ
ESSERE MISURATO DIRETTAMENTE TRAMITE VALUTAZIONE AL MICROSCOPIO DELLA REPLICA PRESA DALLA SUPERFICIE O ALTRO
METODO DIRETTO.
Steel surface preparation check after blasting operation according to ISO 8503; the surface profile shall be measured by direct microscopic
assessment of replica taken from the surface or by other direct methods on blast cleaned steel panels
CONTROLLO CLORURI DELLA SUPERFICIE DOPO SABBIATURA IN ACCORDO ALLA ISO 8502-2 ;
2
CRITERIO ACCETTABILITA’: CONTENUTO CLORURI INFERIORE A 60 µgm/m
Salt test of steel surface after blasting operation according to ISO 8502-2; Acceptance criteria: Chlorides contents lower than 60 µgm/m2
CONTROLLO CLORURI GRANIGLIA PER SABBIATURA ; CRITERIO ACCETTABILITA’: CONTENUTO CLORURI INFERIORE A 100 mg/l
Salt test of abrasive blasting; Acceptance criteria: Chlorides contents lower than 100 mg/l
2
CONTROLLO SPESSORE TOTALE IN ACCORDO ALLA SSPC PA 2 ; NUMERO MINIMO DI MISURAZIONI PER M DI AREA ISPEZIONATA 5
DOVE OGNI MISURAZIONE E’ LA MEDIA DELLE TRE MISURAZIONI INDIVIDUALI COMPRESE IN UN CERCHIO CON DIAMETRO DI 4 CM
Check of total DFT According to SSPC‐PA 2; minimum number of spot measurements 5 where each spot measurements to comprise the
average of at least 3 individual readings within a 4 cm diameter circle
TEST DI ADESIONE SOLO IN CASO DI DUBBIO SULLA QUALITA’ DELLA VERNICIATURA IN ACCORDO ALLA ASTM D4541;
CRITERIO DI ACCETTABILITA’: 5 MPa PER RIVESTIMENTI ESTERNI
Adhesion test applicable only when there is a doubt in painting quality according to ASTM D4541;
Acceptance criteria: minimum for external coatings 5 MPa
CONDISIONI AMBIENTALI DEVONO ESSERE REGISTRATE 4 VOLTE AL GIORNO SUL POSTO DI LAVORO ES. TEMPERATURA ATMOSFERICA,
RELATIVA UMIDITA’(<85%), PUNTO DI RUGGIADA, TEMPERATURA SUPERFICIE METALLO ( DA 10°C A 50°C E 3°C MIN SOPRA IL PUNTO
DI RUGGIADA)E CONDIZIONI GENERALI AMBIENTALI
Ambient conditions have recorded at least 4 times per day at the place of work i.e. atmospheric temperature, relative humidity(<85%),
dew point, metal surface temperature ( 10°C to 50°C and 3°C min above dew point)and general weather conditions

REMARK
Painting cycle applicable on carbon steel material with operating temperature -35°C to 120°C
according to Spec. AKA-001-RA-7754-00001 Rev. 1 System LC1-N

1 29/01/2013 S.Frazzi Q.C.M D.Morelli Revisionato come da commenti cliente / Revised as per client comments
0 11/01/2013 S.Frazzi Q.C.M D.Morelli Invio per approvazione / Issue for approval
Rev: Date: Prepared: Approved: Description:
Carbozinc®858
Product Data formerly Carbozinc 858 (P)

Selection & Specification Data Substrates & Surface Preparation


Generic Type Two component zinc filled, cross linked epoxy General Surfaces must be clean and dry. Employ
primer. adequate methods to remove dirt, dust, oil and
all other contaminants in accordance with
General Carbozinc 858 is high solids, organic zinc epoxy Standard SSPC-SP1.
Properties primer, for protection of structural steel in salt or
weathering environments Steel Blasted to minimum SA2 ½ (ISO 8501-1), SSPC-
SP10, and obtain 25-50 microns (1-2 mils) blast
Features ƒ Easily applicable profile. Alternative blast cleaning with Ultra high
ƒ Cures at low temperatures, 2°C (35°F) pressure water jetting to the standard of min
ƒ Hard tough film CHB2 M.
ƒ Pre-Thinned product, may be applied without
thinner addition Application Equipment
ƒ Good flexibility
ƒ Excellent abrasion resistance Spray This is a high solids coating and may require
ƒ Meets the requirements of SSPC-Paint N° 20 Application adjustments in spray techniques. Wet film
(rev. 11/2004) Type II Level 1. (General) thickness is easily and quickly achieved. The
following spray equipment has been found
Recommended Excellent as a maintenance or general use zinc suitable and is available from manufacturers
Uses epoxy primer over blasted steel. Used within such as Binks, DeVilbiss and Graco.
industry, petrochemical process, off-shore or
other heavy industries in severe environments Conventional Agitated pressure pot equipped with dual
with appropriate topcoats. Spray regulators, 3/8” I.D. minimum material hose,
Recommended for shop application where fast .070” I.D. fluid tip and appropriate air cap.
handling and re-coating are requested.
Airless Spray Pump Ratio: 30:1
Not GPM Output: 3.0 (min.) 11.5 liters/min.
Direct exposure to strong acids and alkalies
Recommended Material Hose: 3/8” I.D. (min.)
Tip Size: .017-.021”
Chemical Splash & Spillage Fumes Output PSI: 2000-2200
Resistance Acids Very Good Excellent Filter Size: 60 mesh
(with proper topcoat) Alkalies Very Good Excellent Teflon packings are recommended and available
Solvents Very Good Excellent from the pump manufacturer.
Salt Water Excellent Excellent
Fresh Water Excellent Excellent Brush & Roller Recommended for touch up, striping of weld
(General) seams and hard-to-coat areas only. Avoid
Color Gray / Green excessive re-brushing or re-rolling.

Finish Gloss Matte Brush Use a medium bristle brush.

Dry Temp. Continuous: 150°C (300°F) Roller Not Recommended.


Resistance Non-Continuous: 200°C (400°F)

Substrates Blasted steel or other as recommended Mixing & Thinning


Compatible May be top-coated with epoxy, polyurethane, or Mixing Power mix separately, then combine and power
Coatings other as recommended mix for a minimum of two minutes.
DO NOT MIX PARTIAL KITS.
Solids Content By Volume: 64 ± 2 %
Ratio 3:1 Ratio by volume (A to B)
Zinc Content By Weight: 85 ± 2 % in dry film
Thinning Normally not required but may be thinned up to
Dry Film 50-150 microns (2-6 mils) 6% by volume, with Thinner N°2. Use of thinners
Thickness than those supplied by Carboline, may adversely
effect product warranty, whether expressed or
Theoretical 25.2 m2/l at 25 microns (1mil) implied.
Coverage Rate 8.4 m2/l at 75 microns (3mils)
Mixing and application losses will vary and must Pot Life 24°C (75°F) 4 Hours lower at more elevated
be taken into consideration when estimating job temperature
requirements. Pot life ends when coating loses body and
begins to sag.
VOC Values VOC+ (Volatile Organic Content) are coating
with high solids, in other words, coating that are
less hazardous, more environmentally safe, and
more economical for the users.

Carboline Italia SpA – Via Milano, 150 – 20093 Cologno Monzese (Mi) – Tel. +39 02 253751 Fax +39 02 2537560 e-mail carboline.italia@stoncor.com
Carbozinc®858 (pag.2)

Cleanup & Safety Packaging, Handling & Storage


Cleanup Use #2 Thinner or Acetone. In case of spillage, Package Part A: 7.5 litres Part B: 2.5 liters
absorb and dispose of in accordance with local Thinner N°2: 20 liters
applicable regulations.
Flash Point (PMCC) Part A: 9°C
Safety Read and follow all caution statements on this Part B: 3°C
product data sheet and on the MSDS for this Thinner N°2 -5°C
product. Employ normal workmanlike safety
precautions. Hypersensitive persons should wear Storage (General) Store Indoors.
protective clothing, gloves and use protective
cream on face, hands and all exposed areas. Storage Temperature 5°-30°C
& Humidity 0-90% Relative Humidity
Caution This product contains flammable solvents. Keep
away from sparks and open flames. All electrical Shelf Life 12 months at 24°C (75°F)
equipment and installations should be made and
grounded in accordance with the National Electric Storage at temperatures higher than 30°C
Code. In areas where explosion hazards exist, reduces the shelf life of Part A considerably
workmen should be required to use non-ferrous
tools and wear conductive and non-sparking
shoes.

Application Conditions
Condition Material Surface Ambient Humidity
Normal 15-30°C 15-30°C 15-30°C 0-90%
Minimum 4°C 2°C 2°C 0%
Maximum 32°C 50°C 43°C 95%

Condensation due to substrate temperatures below the dew point can


cause flash rusting on prepared steel and interfere with proper
adhesion to the substrate. Special application techniques may be
required above or below normal application conditions. Do not apply
when the surface temperature is less than 3°C above
the DEW- POINT

Curing Schedule
Surface Temp. & Minimum Recoat
Final Cure
50% R. H. Time
2°C (35°F) 8 Hours 10 Hours
10°C (50°F) 5 Hours 6 Hours
24°C (75°F) 2 Hours 3 Hours
32°C (90°F) 1 Hour 1 Hour

These times are based on a 75 microns (3 mils) dry film thickness.


Higher film thickness, insufficient ventilation, high humidity or cooler
temperatures will require longer cure times and could result in solvent
entrapment and premature failure.

11/08 – BM mod. 08/07 Norge

Carboline Italia SpA

To the best of our knowledge the technical data contained herein is true and accurate on the date of publication and is subject to change without prior notice. User must contact Carboline
Company to verify correctness before specifying or ordering. No guarantee of accuracy is given or implied. We guarantee our products to conform to Carboline quality control. We assume no
responsibility for coverage, performance or injuries resulting from use. Liability, if any, is limited to replacement of products.
NO OTHER WARRANTY OR GUARANTEE OF ANY KIND IS MADE BY CARBOLINE, EXPRESS OR IMPLIED, STATUTORY, BY OPERATION OF LAW, OR OTHERWISE, INCLUDING
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Carbomastic®15 LT
Product Data

Selection & Specification Data Chemical Resistance Guide


Generic Type Two component, high build, low temperature Splash &
Exposure Immersion Fumes
modified aluminium epoxy mastic. Spillage
Acids NR Good Excellent
General Carbomastic® 15 LT is a high build coating Alkalies NR Good Excellent
Properties with excellent adhesion to rusted steel and Solvents NR Excellent Excellent
most aged coatings. Salt water Excellent Excellent Excellent
Fresh water Excellent Excellent Excellent
Features ƒ Single coat application characteristics.
ƒ Low temperature curing
ƒ Suitable as a tie-coat/topcoat for most Substrates & Surface Preparation
tightly adhered existing coatings.
ƒ Excellent film build on edges. General Surfaces must be clean and dry. Employ
ƒ Excellent choice for field touch-up of zinc adequate methods to remove dirt, dust, oil and
rich primers and galvanized steel. all other contaminants that could interfere with
ƒ VOC compliant to current AIM regulation. adhesion of the coating.

Color Aluminium – Metallic Red Steel Preferably blast in according to SSPC-SP6 /


SP10 with a 50-75 microns (2.0-3.0 mil) surface
Finish Flat profile for maximum protection. However, hand
or power tool cleaning is acceptable standard in
Primers Self-priming. May be applied over most tightly many cases to remove non adhering paints and
adhering coatings as well as inorganic zinc rust (SSPC-SP2, SP3), or SP7 are also
primers. A mist coat may be required to acceptable methods. Alternative blast cleaning
minimize bubbling over inorganic zinc with Ultra High Pressure Water Jetting to the
primers. standard of minimum CHB2

Topcoats Can be top coated with epoxies,


polyurethanes and others as recommended. Application Equipment
Some alkyd or oil modified paints exhibit poor
adhesion. Topcoat recommended within 14 Spray The following spray equipment has been found
days. Application suitable and is available from manufacturers
(General) such as Binks, DeVilbiss and Graco.
Dry Film 75 microns (3.0 mils) over inorganic zinc and
Thickness existing coatings, 125 microns (5.0 mils) on Conventional Pressure pot equipped with dual regulators, 3/8”
rusted steel substrates. Spray I.D. minimum material hose, .070” I.D. fluid tip
200-250 microns (8.0-10 mils) in one or two and appropriate air cap.
coats for severe exposure.
Airless Spray Pump Ratio: 30:1
Solids Content By Volume: 86 ± 2% GPM Output: 3.0 (min.).
Material Hose: 3/8” I.D. (min.)
Theoretical
2
34.4 m / l at 25 microns Tip Size: .023-.027”
Coverage Rate Allow for loss in mixing and application. Output PSI: 2000-2400
Filter Size: 60 mesh
VOC VOC+ (Volatile Organic Compounds) are Teflon packings are recommended and available
coatings with high solids, in other words from the pump manufacturer.
coatings that are less hazardous, more
environmentally safe, and more economical Brush & Roller For touch up, small areas and strip coat only.
for the users. Use a medium bristle brush and medium nap
synthetic roller cover with phenolic core
Dry Temp. Continuous: 120°C (250°F)
Resistance Non-Continuous: 150°C (300°F)

Limitations Epoxies lose gloss, discolor and eventually


chalk in sunlight exposure.

Carboline Italia SpA – Via Milano, 150 – 20093 Cologno Monzese (Mi) – Tel. +39 02 253751 Fax +39 02 2537560 e-mail carboline.italia@stoncor.com
Carbomastic®15 LT (pag.2)

Mixing & Thinning Curing Schedule


Mixing Power mix separately, then combine and Surface Temp. & Dry to
Final Cure
power mix. DO NOT MIX PARTIAL KITS. 50% R. H. Recoat/Topcoat
5°C 18 Hours 7 Days
Ratio 1:1 Ratio by volume (A to B) 10°C 10 Hours 5 Days
20°C 6 Hours 3 Days
Thinning Spray: Up to 25% with Thinner#2 30°C 4 Hours 2 Days
Use of thinners other than those supplied or
recommended by Carboline, may adversely These times are based on recommended DFT. Higher film
effect product performance and void product thickness, insufficient ventilation or cooler temperatures will require
warranty, whether expressed or implied. longer cure times and could result in solvent entrapment and
premature failure.
Pot Life 1 ½ Hours at 20°C and less at higher
temperatures. Note 1: Carbomastic® 15 LT meets the criterias set for NS 5403.
Pot life ends when coating loses body and The complete system will also meet the most stringent
begins to sag. rerequirements in NS 5415.
Note 2: This product contains conductive pigments and cannot be
Cleanup & Safety holiday tested.

Cleanup Use Thinner#2 or 25..


Packaging, Handling & Storage
Safety Read and follow all caution statements on this
product data sheet and on the MSDS for this Shipping Weight
product. Employ normal workmanlike safety Part A: 10lt Part: 10lt
(approximate)
precautions. Hypersensitive persons should
wear protective clothing, gloves and use Carbomastic® 15 LT - A: 0°C
protective cream on face, hands and all Flash Point (Setaflash) Carbomastic® 15 LT - B: 15°C
exposed areas.
Thinner#2: -5°C
Caution This product contains flammable solvents.
Storage (General) Store Indoors.
Keep away from sparks and open flames. All
electrical equipment and installations should
Storage Temperature 5°-45°C
be made and grounded in accordance with
& Humidity 0-100% Relative Humidity
the National Electric Code. In areas where
explosion hazards exist, workmen should be
Shelf Life 24 months at 24°C (75°F)
required to use non-ferrous tools and wear
conductive and non-sparking shoes.

Application Conditions
Condition Material Surface Ambient Humidity
Normal 15-30°C ) 15-30°C 15-30°C 35-80%
Minimum 5°C 2°C 2°C 0%
Maximum 35°C 75°C 40°C 95%

Do not apply when the surface temperature is less than 3°C above
the dew point. Condensation due to substrate temperatures below
the dew point can cause flash rusting on prepared steel. Special
application techniques may be required above or below normal
application condition. Note: this product contains conductive
pigments and cannot be holiday tested.

08/08 – 03/98Norge

Carboline Italia SpA


To the best of our knowledge the technical data contained herein is true and accurate on the date of publication and is subject to change without prior notice. User must contact Carboline
Company to verify correctness before specifying or ordering. No guarantee of accuracy is given or implied. We guarantee our products to conform to Carboline quality control. We assume no
responsibility for coverage, performance or injuries resulting from use. Liability, if any, is limited to replacement of products. NO OTHER WARRANTY OR GUARANTEE OF ANY KIND IS
MADE BY CARBOLINE, EXPRESS OR IMPLIED, STATUTORY, BY OPERATION OF LAW, OR OTHERWISE, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE.
Carbothane®134® HP
(Formerly Carbothane 834)
Product D ata

Selection & Specification Data Substrates & Surface Preparation


Generic Type Acrylic aliphatic polyurethane General Surfaces must be clean and dry. Employ
adequate methods to remove dirt, dust, oil
Description Carbothane 134 HP (formerly Carbothane and all other contaminants that could interfere
834), is an attractive, high gloss, high solids with adhesion of the coating.
urethane topcoat which is easily applied by
airless or conventional spray to yield a hard, Steel Prime with specific Carboline primers or as
very cleanable surface. It exhibits excellent recommended. Refer to the primer’s Product
flow and leveling properties to minimize dry Data Sheet for detailed requirements of the
spray and lampmarks. specific primer or intermediate coat.

Features Excellent weatherability Previously Lightly blast or abrade to roughen surface and
Excellent flexibility Painted degloss the surface. Existing paint must attain
Excellent abrasion resistance Surfaces a minimum 3B rating in accordance with
Meets most VOC (Volatile Organic ASTM D3359 “X-Cut” adhesion test
Content) requirements
Application Equipment
Color Ral Color Chart, is standard, other colors may
be required a special order. Spray This is a high solids coating and may require
Application adjustments in spray techniques. Wet film
Finish High Gloss- with special order, can be (General) thickness is easily and quickly achieved. The
manufactured in LG (Low Gloss) version following spray equipment has been found
suitable and is available from manufacturers
Primers May be used over epoxies, urethanes and such as Binks, De Vilbiss and Graco
others as recommended. Typically applied as
Conventional Pressure pot equipped with dual regulators,
topcoat for CG 893, CM 15 LO/LT, CM 90,
Spray 3/8” I.D. minimum material hose, .070” I.D.
CG 890, CZ 858 (P)
fluid tip and appropriate air cap.
Topcoats Normally none Airless Spray Pump Ratio: 30:1 (min.)
GPM Output: 3.0 (min.)
Dry Film 50-75 m (2.0-3.0 mils) per coat over smooth. Material Hose: 3/8” I.D. (min.)
Thickness Certain colors may require multiple coats for Tip Size: .015”-.017”
adequate hiding. Additional thickness may be Output PSI: 2100-2400
required over rough surfaces for appearance. Filter Size: 60 mesh
Dry Film Thickness in excess of 150 m Teflon packings are recommended and
(6.0 mils) per coat is not recommended. available from the pump manufacturer.

Solids Content By Volume: 65 2% Brush & Roller Multiple coat may be required to obtain
(General) desired appearance, recommended dry film
2
Theoretical 26.m /l at 25 microns thickness and adequate hiding: Avoid
Coverage Rate Allow for loss in mixing and application excessive re-brushing or re-rolling.

Dry Temp. Continuous: 93 C (200 F) Brush Brushing recommended only for touch-up of
Resistance Non-Continuous: 121 C (250 F) small areas. Use natural bristle brush
applying in full stokes. Two coats may be
Limitations Immersion service required to obtain desired appearance, hiding
and recommended DFT

Roller Use a short nap mohair roller with phenolic


core. Avoid rerolling.
Two coats may be required to obtain desired
appearance, hiding and recommended DFT

Carboline Italia SpA – Via Milano, 150 – 20093 Cologno Monzese (Mi) – Tel. +39 02 253751 Fax +39 02 2537560 e-mail carboline.italia@stoncor.com
Carbothane®134 HP (pag.2)
(formerly Carborhane®834)
Mixing & Thinning Application Conditions
Mixing Power mix separately, then combine and Condition Material Surface Ambient Humidity
power mix. Normal 16-29°C 16-29°C 16-29°C 40-60%
DO NOT MIX PARTIAL KITS Minimum 10°C 4°C 4°C 10%
Maximum 38°C 49°C 35°C 80%
Ratio CT 134 HP Part A: 4 by volume
CT 134 HP Part B: 1 by volume Do not apply when the surface temperature is less than 3°C above
the dew point.
Thinning Spray : up to 15% by volume with Th.# 25 Special thinning and application techniques may be required
Brush : up to 10% by volume with Th.#215 above or below normal condition.
Roller : up to 10% by volume with Th.#215
Use of thinners other than those supplied or Curing Schedule
recommended by Carboline may adversely
affect product performance and void product Surface Temp. &
warranty, whether expressed or implied. 50% Relative Dry to Handle and Final Cure
Humidity To Recoat

Pot Life 4 hours at 24°C (75°F) and less at higher 2°C 18 Hours 14 Days
temperature 10°C 8 Hours 7 Days
24°C 4 Hours 3 Days
Pot-life end when material becomes too
32°C 1 Hours 1 Day
viscous to use. This product is moisture
sensitive. Avoid moisture contamination.
These times are based on a 50-75 m dry film thickness.
Excessive film thickness, insufficient ventilation or cooler
Cleanup & Safety temperatures will lengthen cure time.

Cleanup Use #2 Thinner or Acetone. In case of


spillage, absorb and dispose of in accordance Packaging, Handling & Storage
with local applicable regulations.
Kit Standard Part A: 16 liters Part B: 4 liters

Safety Read and follow all caution statements on this


Flash Point (PMCC) Part A: 32°C ( 90°F)
product data sheet and on the MSDS for this
Part B: 53°C (106°F)
product. Employ normal workmanlike safety
Thinner# 25: 30°C ( 87°F)
precautions. Hypersensitive persons should
Thinner#215 54°C (128°F)
wear protective clothing, gloves and use
protective cream on face, hands and all
Storage Temperature Store indoors.
exposed areas.
& Humidity 4°-43 C (40°-110 F)
0-80% Relative Humidity
Ventilation When used as a tank lining or in enclosed
areas, thorough air circulation must be used
Shelf Life 24 months at 24 C (75° F)
during and after application until the coating is
NOTE: Polyurethane materials are
cured. The ventilation system should be
moisture sensitive. Keep tightly covered
capable of preventing the solvent vapor
before use. Moisture contamination will
concentration from reaching the lower
cause poor cure of the coating or
explosion limit for the solvents used. User
gellation of Part B
should test and monitor exposure levels to
insure all personnel are below guidelines. If
not sure or if not able to monitor levels, use
MSHA/NIOSH approved supplied air
respirator.

Caution This product contains flammable solvents.


Keep away from sparks and open flames. All
electrical equipment and installations should
be made and grounded in accordance with the Carboline Italia SpA
National Electric Code. In areas where
explosion hazards exist, workmen should be
required to use non-ferrous tools and wear
conductive and non-sparking 02/12-08/08 ITA CT 834

To the best of our knowledge the technical data contained herein is true and accurate on the date of publication and is subject to change without prior notice. User must contact Carboline
Company to verify correctness before specifying or ordering. No guarantee of accuracy is given or implied. We guarantee our products to conform to Carboline quality control. We assume no
responsibility for coverage, performance or injuries resulting from use. Liability, if any, is limited to replacement of products. NO OTHER WARRANTY OR GUARANTEE OF ANY KIND IS
MADE BY CARBOLINE, EXPRESS OR IMPLIED, STATUTORY, BY OPERATION OF LAW, OR OTHERWISE, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE.

S-ar putea să vă placă și