F= 245200 [N]

D1= -90 [mm] G= 76923.0769 [N/mm2] MODULO DE CIZALLAMIENTO

D2= 88.9 [mm] τ= 39.5027256 [N/mm2] ESFUERZO DE CORTE TRANSVERSAL EN BARRA 85mm
L= 31.75 [mm] τ lim = 200 [N/mm2] ESFUERZO DE CORRTE LIMITE
v1 = 0.3 [] Aparentemente la barra no fallaría por cizallamiento pero se debería chequear el criterio de falla.
v2= 0.3 [] Si es un gancho no tener en cuenta calculo de cizallamiento.
E1= 200000 [N/mm2]
E2= 200000 [N/mm2]
Sy = 400 [N/mm2]

2F/πL = 4916.50923415846
(1-v^2)/E = 4.55E-06
1/D1 = -0.011111111111111
1/D2 = 0.011248593925759
Perimetro 90 282.743338823081

b= 18.0395175424493 [mm] SEMIANCHO

2b = 36.0790350848986 [mm] ANCHO
A= 1145.50936394553 [mm2] AREA CONTACTO
α= 45.9372542059802 [grados] ANGULO DE CONTACTO
q= 214.053248028848 [N/mm2] CARGA DISTRIBUIDA SOBRE GANCHO

CASO 1
F= 245200 [N]
D1= -90 [mm]
D2= 85 [mm]
L= 22.22 [mm]
v1 = 0.3 []
v2= 0.3 []
E1= 200000 [N/mm2]
E2= 200000 [N/mm2]
Sy = 400 [N/mm2]
VM max = 683 [N/mm2]

CASO 2
F= 245200 [N]
D1= -90 [mm]
D2= 85 [mm]
L= 25.4 [mm]
v1 = 0.3 []
v2= 0.3 []
E1= 200000 [N/mm2]
E2= 200000 [N/mm2]
Sy = 400 [N/mm2]
VM max = [N/mm2]

CASO 3
F= 245200 [N]
D1= -90 [mm]
D2= 85 [mm]
L= 31.75 [mm]
v1 = 0.3 []
v2= 0.3 []
E1= 200000 [N/mm2]
E2= 200000 [N/mm2]
Sy = 400 [N/mm2]
VM max = 464 [N/mm2]

CASO 4 3D assembly
F= 245200 [N]
D1= -90 [mm]
D2= 88.9 [mm]
 L= 31.75 [mm]
v1 = 0.3 []
v2= 0.3 []
E1= 200000 [N/mm2]
E2= 200000 [N/mm2]
Sy = 400 [N/mm2]
VM max = [N/mm2]

CASO 4 2D hertz tension

F= 245200 [N]
D1= -90 [mm]
D2= 88.9 [mm]
L= 31.75 [mm]
v1 = 0.3 []
v2= 0.3 []
E1= 200000 [N/mm2]
E2= 200000 [N/mm2]
Sy = 400 [N/mm2]
VM max = 457 [N/mm2]
VERSAL EN BARRA 85mm

a chequear el criterio de falla.