Documente Academic
Documente Profesional
Documente Cultură
p/n 2230500000
SERVICE MANUAL
ATTENTION:
WARRANTY SERVICE PROCEDURES
The Blues Junior™ III Amplifier is considered to be field serviceable to the component level.
As such stuffed PCB Assemblies are not readily available for this unit. Any Fender Authorized
Service Center in need of a warranty replacement PCB Assembly for this unit should contact
FMIC Tech Support by phone at (866) 345-3642, or by email sent to: service@fender.com.
Fender Musical Instruments Corp. / 8860 East Chaparral Rd, Suite 100 / Scottsdale, AZ 85250
Issued: June, 2010
IMPORTANT NOTICE
• Copyright © 2010 FMIC. All rights reserved. All change without notice. This information and any
information contained herein is CONFIDENTIAL copies produced electronically or otherwise must
and PROPRIETARY and is the property of Fender be surrendered upon demand of Fender Musical
Musical Instruments Corporation. It is not to be Instruments Corporation.
sold or assigned to another party and is disclosed
solely for use by Fender® Authorized Service • Parts marked with two asterisks (**) indicate the
Centers for purposes of product service and required use of that specific part. This is
maintenance. All information is not to be necessary for RELIABILITY and SAFETY
disclosed to others without the expressed requirements.
permission of Fender Musical Instruments DO NOT USE A SUBSTITUTE!
Corporation. All specifications are subject to
SPECIFICATIONS
Model Name: BLUES JUNIOR III Combo
Power Amp Sensitivity: 10mV for full power into 8 ohms, Tone and Volume = 12
SERVICE NOTES
1. PCB ACCESS is accomplished by removing six 3. PCB ASSEMBLY REMOVAL is accomplished
(6) upper screws from the cabinet back panel. by removing the following items: six (6) knobs,
Please note that the lower (2) screws are used six (6) knob spacer bushings, one (1) input jack
to secure P/N 00 COVER TUBE BLUES nut and washer, and seven (7) PCB mounting
JUNIOR screws. Remove the chassis ground screw
from the green wire at the right of the PCB.
2. CHASSIS REMOVAL is accomplished by Disconnect the power transformer and output
removal of two (2) screws at the cabinet top transformer leads at P1-P18. Remove the
and two (2) screws at the cabinet sides. power LED from the red jewel lens cap by
Disconnect the ¼” speaker plug from the gently pulling out the tulip assembly.
speaker jack. Disconnect two (2) RCA
connections at the reverbs tank to free the 4. BREAKAWAY (TUBE) PCB REMOVAL is
cables from the reverb tank. After all cables are accomplished by removing the five (5) tubes
disconnected, slide the chassis toward the rear and nine (9) screws and nuts.
of the cabinet.
CIRCUIT DESCRIPTION
This section provides concise information about MASTER volume control, which couples to the input
new or unusual circuitry designs incorporated into of the Phase Inverter (V3).
this amplifier model. The purpose is to aid the
service technician by providing insight into the
POWER AMPLIFIER
design areas most likely to become obstacles in
troubleshooting. Information is focused for its
effective use while maintaining the security of The output tubes (6BQ5/EL84) are arranged in a
Fender® proprietary information wherever possible. push-pull configuration that will produce fifteen (15)
PRE-AMPLIFIER watts R.M.S. into eight (8) ohms @ 5% THD, 1kHz.
* Non-serviceable part. Replace complete parent assembly. See PCB EXCHANGE POLICY section above.
shaded Unique Fender® part. Order directly from the FMIC Parts Department.
shaded + * Access to this part or assembly is controlled. Please contact the FMIC Customer Service Department.
** Safety Requirement part. Replacement must match Safety Agency…–Value, if specified –Type, if specified –Approval Mark(s) if on part.
shaded + ** Both a unique Fender® part and a Safety Requirement part as defined above.
24
29
12
11
37 6X D
2X 10
11
2
30 6X
SERVICE MANUAL DOCUMENT
10/25/2010
13
15 2X
2 REF
18 14 2X
29 REF
15
28 .125
C
ITEM 31 (FOAM TAPE) PLACEMENT DETAIL
23 SCALE: 1/1
8
9
17 4X
22
ANGLES
CHKD S.M.E. (OPT) MGR/DIR P.E. SIZE PART NUMBER REV
ANGLES-------------- 0.5
UNMARKED ANGLES---90
DATE DATE DATE DATE
D 0079649000 ASSEMBLY A
DO NOT SCALE DRAWING FILE NAME: SCALE: NONE SHEET: 1 of 1
TITLEBLOCK REVISION: 1.8
8 7 6 5 4 3 2 1
D
17
14
18
2X 35
7 17/32"
33 REF
37 34 8X
3/4"
15
9
5 6X
C
13 4X
36 4X
8 4
2X 6
12
13
38 2 LABEL CARB 93120 COMPLIANCE
37 1 FOAM TAPE 1/4" 1/16 3M4516 B
36 4 EYELET RFLNGD .215 OD x.315 L
35 2 SCRW M 10-32X1/2 THP NI
34 8 PIN ESCUTCHEON #18 x 1/4 NI
33 1 NAMEPLATE BLUES JUNIOR III
2 32 1 LABEL VOLTAGE
7
18 1 LABEL AMP PRODUCT NOM
33
17 1 LABEL CSA C/US
16 4 PIN ESCUTCHEON #18x3/8 NI
4X 16 15 1 PANEL REAR BLUES JUNIOR III
14 1 "LABEL SERIAL ""B"" BLK ON CHRM"
13 5 SCRW PB 8x3/4 PHP ZI
12 1 CLAMP CABLE NYL SCRW MNT 5/16
11 1 REVERB UNIT 800 ohm 8EB2C1B DN
10 1 LABEL TUBE BLUES JUNIOR III
9 1 COVER TUBE BLUES JUNIOR
8 1 LABEL SPKR 12" 8 OHM STL CER
6 2X 7 1 CABLE ASSY SPKR RT ANG 13-1/2"
6 4 SCRW M 10-32x1-1/2 THP NI
5 6 SCRW M 10-32x3/4 THP NI
4 1 CHASSIS ASSY BLUES JUNIOR III
3 4 SCRW M 10-32 3/4 THP STL BLX
2 1 SPKR 12 INCH 8 OHM STL CER
38 2X
10 1 1 CABINET ASSY BLUES JR III
ITEM QTY DESCRIPTION
GENERAL TOLERANCES ENGINEER DATE
FENDER MUSICAL INSTRUMENTS CORP.
R
UNLESS OTHERWISE SPECIFIED 01-14-2010 RESEARCH AND DEVELOPMENT
WOOD FRACT------ 1/32
ENGLISH METRIC
DRAWN DATE
CORONA, CALIFORNIA U.S.A. A
X----------------------- 1
.X----------------------- .050 0.5 01-14-2010 TITLE
.XX--------------------- .020 0.25
MATERIAL .XXX------------------- .010
HOLE DIA.----------- +.005 -.001 +0.13 -0.03 CHKD DATE
1 WOOD HOLE DIA- .005 0.13
N/A ANGLES
ANGLES------------- 0.5
UNMARKED ANGLES--90 S.M.E. (OPT) DATE
END ITEM ASSEMBLY BLUES JUNIOR III