Documente Academic
Documente Profesional
Documente Cultură
Professional Objective: Seeking a position to utilize my skills and abilities in the Electronic Industry
that offers a professional growth while being resourceful, innovative and
flexible.
Email Id : tushar3377@yahoo.co.in .
WORK EXPERIENCE
4.6 Years +
EDUCATIONAL QUALIFICATION
Personnel Skills
PLC: - Unitronics.
GSM Modem: - Siemens TMAS or visiontek.
Communication:- RS 232, RS 485, Modbus protocol.
Depending upon Day time & water Level in Over head tank Pump will start & stop in Local auto
cycle. Same for motorized operated valve which provides distribution of water.
Using GSM communication, Master station gets status of slave station. As slave station sends a SMS
for each status change. That is decoded by master & Indicates on Master Panel, Mimic Panel & PC.
PC & Master Panel can also give command to any of slave for any operation of PUMP, BOREWLL,
and Motorized operated valve. Every Slave including master has separate SIM nos. acts as station ID.
PLC: - Unitronics.
RF Modem: - Maxon, TSLM Data radio.
Communication: - RS 232, RS 485, Modbus protocol.
In RF communication, PLC’s are interfaced using RF modem; Station ID is set in PLC. Master PLC
Polls data from slave. Both read & write operation is possible. All operations of GSM can be done.
PLC: - Messung.
GPRS Modem: - LEO.
Communication: - RS 232, Ethernet, WLAN, Modbus protocol.
Data transfer to Master computer which has static IP is through mobile internet. Each PLC
(Messung) is connected with GPRS Modem which has GPRS enabled SIM. Station ID & Static IP
address is o set in PLC. Data transfer takes place due to common server i.e. SIM service provider’s
server.
Pipeline pressure, flow & tank water level is transmitted to master. WLAN to write command to
slave.
MORDE FOODS PVT. LTD. (15 September 2008 –14 February 2010)
This system will make 0.5 kg chocolate mold. This plant will make 35 molds per minute.
PLC - SCHNEIDER having Analog (Input & Output), Digital (Input & Output),, & Counter card.
SCADA - GE-FANUC, PROTOCOL – MODBUS.
VFD – ABB, SERVO DRIVE – REXROTH.
This Plant will make Cocoa Powder from Cocoa cake kibbles.
PLC – SIEMENS (S7-300), ET-200S PLC. having Analog (Input), Digital (Input & Output) Card &
Remote I/O having
SCADA- SIEMENS, PROTOCOL – PROFIBUS.
VFD – DANFOSS.
Air circulation through plant is achieved through blower. Air speed feedback is taken through
anemometer. Three ways mixing valve operates from PLC (Analog output 4-20mA) in PID action.
PLC – ALLEN-BRADLEY having Analog (Output), Digital (Input & Output) Card.
PROTOCOL – No Protocol (Serial Communication).
VFD – ABB, SERVO DRIVE – REXROTH.
Analog output from PLC drives the Servomotor drive causes forward & backward motion of Piston.
Speed & Stroke Length is to be adjusted by Allen Bradley Scada.
PLC – Messung having Analog (Output), Digital (Input & Output) Card & RTD card.
PROTOCOL – MODBUS.
VFD – ABB.
Analog output from PLC drives chocolate circulating pump drive. Temperature of various zones is
measured by respective RTD. Depending upon actual temperature & set points Heaters & cold water coils
operates in PID. So that each zone temperature will remain constant.
PLC – Messung having Analog (Output), Digital (Input & Output) Card & RTD card.
PROTOCOL – MODBUS.
VFD – ABB.
Analog output from PLC drives Roll motor drive. Temperature of roll is measured by respective RTD.
Hydraulic motor & solenoid coil causes optimum roll pressure. Depending upon roll gap setting
respective particle size can be achieved.
Worked in Commissioning & Troubleshooting of project.
MECHATRONICS SYSTEM PVT. LTD. . (15 July 2006 – 1 Sepetmber 2008)
It has Microcontroller 89C52, PPI 8255, Optocoupler MCT6, MAX 485, BBRAM 48Z08,
Latch 74373, DIP switches for station ID & Watchdog MAX691.
Worked on both Hardware & Software of the system & on both types GMS-485, GMS-300.
This system will measure Temperature (LM35). It has temperature sensor which will give voltage o/p &
is read by ADC(7135). Controller will give temperature. Which will be transmitted through 485.
It has Microcontroller 89C2051, ADC 7135, Watchdog MAX691 and MAX 485.
This System will measure the Canal gate level in Millimeters. Also control gate movement in Up &
down Direction & Transmits gate level & various parameters from Local Site to Central Control Room.
It has Microcontroller 89C669, SRAM, Optocoupler MCT6, MAX 485, Watchdog MAX691 and
Latch 74373.
This System will track vehicle anywhere in India. It constitutes GPS which will give Lat, Long of the
vehicle & GSM will send message of Lat, Long to control station. It also has voice communication
facility.
It has Microcontroller 89C668, SRAM, GPS Engine board, Mobile handset, Watchdog MAX691 and
Latch 74373.
This System will give water level of Dam &Canal. Depending on sensor range & Datum level.
It has Microcontroller 89C52, Watchdog MAX691, ADC 7135, MAX 485 and Latch 74373
Worked on Hardware & Testing.
This System has 4 Analog i/ps & 20 Digital i/ps, to read various parameters. It has 1 CPU, 1 LCD-KBD
card, 2 ADC & 2 I/O cards. It is Mini PLC.
It has Microcontroller 89C669, Optocoupler MCT6, MAX 485, Watchdog MAX691 and
Latch 74373, PPI 8255, RTC 48T08.
AREAS OF INTERESTS
PERSONAL DETAILS
Date of Birth : 21st March 1984
Nationality : Indian
Sex : Male
Declaration
I hereby declare that the above written particulars are true to the best of my
knowledge and belief.