Documente Academic
Documente Profesional
Documente Cultură
Authorised by agreement between the Royal Institution of Chartered Surveyors and the Construction Confederation Seventh Edition Revised 1998
~i
Co-ordinated project information
First Edition, 1922 Second Edition, 1927 Third Edition, 1935 Fourth Edition, 1948 Fifth Edition, 1963; amended 1964; Sixth Edition, 1979 Seventh Edition, 1988 Reprinted 1989 incorporating Amendment Sheets Nos 1 and 2 dated September 1988 and May 1989. Reprinted 1992 incorporating Amendment Sheets Nos 1,2 and 3 dated September 1988, May 1989 and May 1992. Revised and Reprinted 1998 Reprinted 2000 incorporating Amendment Sheets Nos 1 and 2, both dated 2000 Reprinted 2009 incorporating Amendment Sheets Nos 1 and 2, both dated May 2000, and Amendment Sheet No 3 dated June 2009 Copyright
©1998
ISBN 0 854063609 (RICS) ISBN 0 852630043 (CC) All rights reserved. No part of this publication covered by the above copyright may be reproduced, stored in a retrieval system or transmitted in any form or by any means without the prior permission of the copyright owners. Designed and set by NBS Services ltd, Newcastle upon Tyne Ae-set and printed by Thanet Press, Margate, Kent.
contents
Summary of
To find the relevant work section for any given topic refer to the detailed contents list overleaf or to the alphabetical index.
Detailed contents
Preface General rules A
Page 1
conditions
C
D E F G
Stru ctu fa IICa rc assing meta IItimbe r Cladding/Covering Waterproofi ng linings/Sheathing/Dry Windows/Doors/Stairs Surface finishes Furniture/Equipment Building fabric sundries partitioning
H J K
l M N P Q
R
S T
U
V W
X Y
Alphabetical1index
Page 183
Detailed contents
Preface Preface Preface General to First Edition 1922 to Seventh Edition 1988 to Seventh Edition Revised 1998 Rules 8 9 10 11
D
A
A40
Preliminaries/General conditions
A40 A41 A42 A43 A44 A50 A51 A52 A53 A54 ASS A60 A61 A62 A63 A64 A70 20 20 20 21 21 21
A
AlO All A12 Al3 A20 A30
17 17 17 17
18 18 18 18 18 18
A31
A32 A33 A34 A35 A36 A37
19
Contractor's general cost items: Management and staff A41 Contractor's general cost items: Site accommodation A42 Contractor's general cost items: Services and facilities A43 Contractor's general cost items: Mechanical plant A44 Contractor's general cost items: Temporary works A50 Works/Products by/on behalf of the Employer AS1 Nominated sub-contractors A52 Nominated suppliers A53 Work by statutory authorities/undertakers A54 Provisional work ASS Oayworks A60 Preliminaries/General conditions for demolition contract A61 Preliminaries/General conditions for investigationlsurvey contract A62 Preliminaries/General conditions for piling/embedded retaining walls contract A63 PreliminarieslGeneral conditions for landscape contract A64 Preliminaries/General conditions for building services contract A70 General specification requirements for work package
22 22 22 22 22
* * * * *
19
B
Bll
E
810
B11
810 Prefabricated
* *
cia
Cll C12 C13 C14 C20
C21
C30 C40 C41 C42 C45 C50 C51 C52 C90
Cl1 C12 C13 C14 C20 C21 C30 C40 C41 C42 C45 C50 C51 C52 C90
cia
* * * * *
23 23 23 25 25 25 27 27 27 27 28
E05 EIO Ell E20 E30 E31 E40 E41 E42 E50 E60
43 43
45 46
49
50 50 51 52
53 54
F
FlO Fl1 F20 F21 F22 F30 F31
Masonry
Brick/Block walling Glass block walling Natural stone rubble walling Natural stone ashlar waiting/dressings Cast stone ashlar walling/dressings Accessories/Sundry items for brick/block/stone Prec ast concrete si IIs/llntels/c opings/features
FlO
Fl1 F20 F21 F22 F30 F31
walling
55 55 58 58 58 62
53
G
011
D Groundwork
D30
040 041 D50
Soil Stabilization Site dewatering Excavating and filling Ground gas venting Piling Embedded retaining walls Crib walls/Gabions/Aeinforced Underpinning
* *
29
*
33 38 40 41
D40
earth 041 050
fibre decking
70 70
H
HIO HI1 H12 H13 H14 H2O H21 H30 H31 H32 H33 H40 H41 H42 H43 H50 H51 H52 HoO H61 H62 H63 H64 H65 H66 H70 H71 H72 H73 H74 H75 H76 H90 H91 H92
Cia dd ing/Coveri ng
Patent glazing Curtain walling Plastics glazed vaulting/walling Structural glass assemblies Concrete rootlights/pavement lights Rigid sheet cladding Timber weatherboarding Fibre cement profiled sheet cladding/covering/siding Metal profiled sheet cladding/covering/siding Plastics profiled sheet cladding/covering/siding Bitumen and fibre profiled sheet cladding/covering Glassfibre reinforced cement panel cladding/features Glassfibre reinforced plastics panel cladding/features Precast concrete panel cladding/features Metal panel cladding/features Precast concrete slab cladding/features Natural stone slab cladding/features Cast stone slab cladding/features Plain roof tiling Fibre cement slating Natural slating Reconstructed stone slating/tiling limber shingling Single lap roof tiling Bituminous felt shingling Malleable metal sheet prebonded coverings/cladding lead sheet coverings/flashings Aluminium strip/sheet coverings/flashings Copper strip/sheet coverings/flashings Zinc strip/sheet coverings/flashings Stainless steel strip/sheet coverings/flashings Fibre bitumen thermoplastic sheet coverings/flashings Tensile fabric coverings Thatch roofing Rainscreen cladding
J
HIO Hll H12 HI3 H14 H2O H21 H30 H31 H32 H33 H40 H41 H42 H43 H50 H51 H52 H60 H61 H62 71 72 71 71 73 73 73 75 75 75 75 53 75 53 75
53
77
JIO J20 J21 J22 J30 J31 J32 J33 J40 J41 J42 J43 J44
Waterproofing
Specialist waterproof rendering Mastic asphalt tanking/damp proofing Mastic asph alt roofing/in sulation/finishes Proprietary roof decking with asphalt finish Liquid applied tanking/damp proofing Liquid applied waterproof roof coatings Sprayed vapour control layers In situg lassfi bre reinforc ed piasties Flexible sheet tanking/dampproofing Built up felt roof coverings Single I.ayer polymeric roof coverings Proprietary roof decking with felt finish She et lini ngs for pools/I akes/wate rways
JIO J20 J21 J22 J30 J31 J32 J33 J40 J41 J42 J43 J44
103 83 83 83 83 83
...
_,,_
85 85 85 85 85
K Kll
H64 H65 H66 H70 H71 H72 H73 H74 H75 H76 H90 H91 H92
H63
79 79 79 79 79 79 79 80 80 80 80 80 80 * * 73
80
77
K12 K13 K14 K15 K20 K21 K30 K32 K33 K40 K41
Kl0 Kll KI2 K13 KI4 K15 K20 K21 K30 K32 K33 K40 K41
87 73 73 73 73 73 73 73 90 91
53
92 94
L
110 L20
Windows/Doors/Stairs
WindowsiRooflights/Screens/louvres Doors/Shutters/Hatches Sta irsfWa lkways/Ba lustrades General glazing lead light glazing Infill panels/sheets LIO L20 l30 L40 L41 l42 95
96
97 98 101 102
l30
L40 L41 l42
M Surface finishes
Ml0 Mll M12 M13 M20 M21 M22 M23 M30 M31 M40 M41 M42 MSO MS1 M52 M60 M61 Cement: sand/Concrete screeds/toppings Mastic asphalt flooring/floor underlays Trowelled bitumen!resin/rubber-Iatex flooring Calcium sulfate based screeds Plastered/Rendered/Roughcast coatings Insulation with rendered finish Sprayed monolithic coatings Resin bound mineral coatings Metal mesh lathing/Anchored reinforcement for plastered coatings Fibrous plaster Stone/Cone rete/Quarry/Ceramic tiling/Mosa ic Terrazzo tiling/In situ terrazzo Wood block/Composition block/Parquet flooring Rubber/Pia stics/Cork/Lino/Ca rpet tiling/sheeting Edge fixed carpeting Decorative papers/fabrics Painting/Clear finishing Intumescent coatings for fire protection of steelwerk Ml0 MIl MI2 M13 M20 M21 M22 M23 M30 M31 M40 M41 M42 M50 M51 M52 M60 M61 103 83 103 103 103 106 107 103 108 109 111 113 111 113 113 115 116 116
Nl0 General fixtures/fumishi ngs/eq uipment Nil Domestic kitchen fittings NI2 Catering equipment NI3 Sanitary appliances/fittings NI5 Signs/Notices N16 BirdNermin control N20 N21 } Special purpose fixtureS/lurnishings/equipment N22 N23
Furniture/Equipment
NIO Nil NI2 NI3 NI5 N16 N20 N21 N22 N23 119 119 119 119 119 * * * * *
PIO Sundry insulation/proofing work/fire stops Foamed/Fibre/Bead cavity wall insulation Pit items P20 Unframed isolated trims/skirtings/sundry P21 Door/Window ironmongery P22 Sealant joints for buried engineering services P30 Trenches/Pipeways/Pits for services P31 Holes/Chases/Covers/Supports
Q
010 020 021 022 023
Kerbs/Ed ging s/Chan nels/Pav; ng accessori es Granular sub-bases to roads/pavings In situ concrete roads/pavings Coated macadam/Asphalt roads/pavings GravelJHoggin/Woodchip roads/pavings 024 Interlocking brick/block roads/pavings 025 Siab/Brick/Block/Sett/Cobble pavings 026 Special surfacings/pavings for sport/general amenity Q30 Seeding/Turfing Q31 External planting 032 Internal planting 035 Landscape maintenance Q40 Fencing Q41 Barriers/Guardrails 050 Site/Street furniture/equipment *No specific rules included - see General rules clause II
021
022 Q23 Q24 Q25 026 030 Q31 Q32 035 Q40 Q41 050
29
132 133 134 135 135 136 137 137 137 * 139 97 119
II
R
RIO Rll R12 Rl3 R14 R20 R21 R30 R31 R32 R33
Disposal systems
Rainwater pipework/gutters Foul drainage above ground Drainage below ground Land drainage Laboratory/Industrial waste drainage Sewage pumping Sewage treatment/sterilisation Centralised vacuum cleaning Refuse chutes Compa ctors/M acerators Incineration plant RIO Rll R12 R13 Rl4 R20 R21 RJO R31 R32 R33 141 141 145 145 y y Y
T
Tl0 Til T12 T13 T14 T15 T16
y
y
Y
Y
Y Y
no
y y
y Y y
S
S10 S11 Sl2 S13 S14 S15 S20 S21 S30 S31 S32 S33 S34 540 S41 S50 S51 S60 S61 S62 S63 564 S65 S70 S71
y
y
y
Y
T30 T31 T32 T33 T40 T41 T42 T50 T60 T61
y y y y y
y y y
y y y Y Y Y y Y
DO
TIl T72
T72
y y y
y y
V y
Y y y y
y Y See Y Mechanical and electrical services measurement
U
Ul0 U11 U12 U13 U14 U15 U16 U17 U20 U30 U31 U32 U33 U40 U41 U42 U43 U50 U60 U70
W Communications/Security/Control
y y y
y WlO W11 W12 W20 W21 W22 W23 W30 W40 W41 W50 W51 W52 W53 W54 W60 Telecommunications Paging/Emergency call Public address/Conference audio facilities Radio/TV/CClV Projection Information/Advertising display Clocks Data transmission Access control Security detection and alarm Fire detection and alarm Earthing and bonding Lightning protection EIectromagneti c sc reeni ng liquid detection alarm Central control/Building management
systems
Wl0 Wl1 W12 W20 W21 W22 W23 W30 W40 W41 WSO W51 W52 W53 W54 W60
y Y Y Y
Y Y Y V Y Y Y Y
y y y y y y Y y y y y
Y V V
Y Y y
Y
Y y
V
Vl0 Vll V12 V20 V21 V22 V30 V31 V32 V40 V41 V42 V50 V51 V90
Electrical supply/power/lighting
systems
Vl0 Vll V12 V20 V21 V22 V30 V31 V32 V40 V41 V42 V50 V51 V90
Electricity generation plant HV supply/distribution/public utility supply LV supply/public utility supply LV distribution General lighting General LV power Extra low voltage supply DC supply Uninterruptable power supply Emergency lighting Street/Area/Flood lighting Studio/Auditorium/Arena lighting Electric underfloor/ceiling heating Local electric heating units Electrical installation (self-contained specification)
y y y Y y y y
Y
Y Y
Transport Systems
Lifts Escalators Moving pavements Powered stairlifts Fire escape chutes/slings Hoists Cranes Trave lIin9 crad les/g antries/la dders Goods distribution/Mechanised warehousing Mechanical document conveying Pneumatic document conveying Automatic document filing and retrieval X10 Xl1 X12 X13 X14 X20 X21 X22 X23 X30 X31 X32 149 149 149 149 149 149 149 149 149 149 149 149
X23
X30 X31 X32
Y Y Y
y y
Y See Y Mechanical
1m
fJ
V
Yl0 Yll Y20 Y21 Y22 Y23 Y24 V25 Y30 Y40 Y41 Y42 Y43 Y44 Y45 Y46 Y50 Y51 Y52 Y53 Y54 Y59 Y60 Y61 V62 Y63 Y70 Y71 Y72 Y73 Y74 Yoo V81 VB2 V89 Y90 Y91 Y92
Appendices
A B Fixtures, furnishings, equipment, fittings and appliances Classification of mechanical and electrical services
177
181
Alphabetical index
183
11
E.
Others who have served on the Committee or the Development Unit during the preparation of this edition: Dr Martin Barnes, Robert A. Barrow, Ian T. Brown, Peter Graham, Alan M. Harrison, Patrick Kelly, Anthony R. Miller and Paul D. Morrell. Consultant Editors appointed by the Committee: Paul J. Gilkes and Richard E.N. McGill CJW: 1 October 1987
1998
The Joint Committee responsible for this Amended Edition at the date of issue was composed as follows: Appointed by the Royal Institution of Chartered Surveyors: Ronald CAllan (Chairman), Keith W. Bailey, Andrew O'Kelly, Michael A Rainbird, and Michael B.Smith. Appointed by the Construction Confederation: Donald J Rimmer (Vice Chairman), Kevin M.Callan, Brian W.Gordon, and Richard J
. Hooker.
Consultant members of the committee Andrew J.Costelioe and Christopher J Willis Joint Honorary Secretaries: Norman R. Wheatley (General) and John D.O'N.Davidson (Queries). RCA: 1 July
1998
III
General rules
1. Introduction
2.5
The left hand column of the classification table lists descriptive features commonly encountered in building works. The next column lists further sub-groups into which each main group of items shall be divided and similarly the third column provides for further division. The lists in these columns are not intended to be exhaustive.
1.1 This Standard Method of Measurement provides a uniform basis for measuring building works and embodies the essentials of good practice. Bills of quantities shall fully describe and accurately represent the quantity and quality of the works to be carried out. More detailed information than is required by these rules shall be given where necessary in order to define the precise nature and extent of the required work.
2.6
Each item descri ption shall identify the wo rk with respect to one descri ptive feature drawn from each of the first three columns in the classification table and as many of the descriptive features in the fourth column as are applicable to the item. The general principle does not apply to Preliminaries in that it will be necessary to select as many descriptive features as appropriate from each column.
1.2
The rules apply to measurement of proposed work and executed work.
2.
2.1
Generally
The rules in this document are set out in tables. Each section of the rules comprises information (to be) provided, classification tables and supplementary rules. The tabulated rutes are written in the present tense.
2.7
Where the abbreviation (or) is given in the classification shall be stated in the item description. table the quantity
2.2
Horizontal lines divide the classification zones to which different rules apply. table and supplementary rules into
Classification tables
2.3 Within the classification table where a broken line is shown, the rules given above and below the broken line may be used as alternatives.
2.4
In referring to columns in classification umn has been disregarded. tables the measurement unit col-
2.11 Coverage rules draw attention to particular incidental work which shall be deemed to be included in the appropriate items in a bill of quantities to the extent that such work is included in the tender documents. Where the coverage rules include materials they shall be mentioned in the item descriptions. 2.12 The column headed Supplementary Information contains rules governing the information which shall be given in addition to the information given as a result of the application of rule 2.6. 2.13 A separate item shall be given for any work which differs from other work with respect to any matter listed as supplementary information.
4.
Descriptions
4.1 Dimensions shall be stated in descriptions generally in the sequence length, width, height. Where ambiguity could arise, the dimensions shall be identified.
4.2
Information required by the application of rules 2.6 and 2.12 may be given in documents (e.g. drawings or specification) separate from the bills of quantities if a precise and unique cross reference is given in its place in the description ot the item concerned. This rufe does not allow the aggregation of a number of measured items which are otherwise required to be measured separately by these rules, except as provided by rule 9.1.
4.3
Headings to groups of items in a bill of quantities shall be read as part of the descriptions of the items to which the headings apply.
3.
3.1
Quantities
4.4 The use of a hyphen between two dimensions in this document or in a bill of quantities shall mean a range of dimensions exceeding the first dimension stated but not exceeding the second.
Work shall be measured net as fixed in position except where otherwise stated in a measurement rule applicable to the work. 3.2 Dimensions used in calculating quantities shall be taken to the nearest 10mm (i.e. 5mm and over shall be regarded as 10mm and less than 5mm shall be disregarded).
4.5
Each work section of a bill of quantities shall begin with a description stating the nature and location of the work unless evident from the drawn or other information required to be provided by these rules.
4.6
Unless otherwise specifically stated in a bill of quantities following shall be deemed to be included with all items: (a) Labour and all costs in connection (c) Assembling, therewith. therewith. (b) Materials, goods and all costs in connnection (d) Plant and all costs in connection therewith. (e) Waste of materials and all costs in connection with dispasal. (f) Square cutting. (g) Establishment charges, overhead charges and profit. or herein, the
3.3
Quantities measured in lonnes shall be given to two places of decimals. Other quantities shall be given to the nearest whole unit except that any quantity less than one unit shall be given as one unit.
3.4
Unless otherwise stated, where minimum deductions for voids are dealt with in this document they shall refer only to openings or wants which are within the boundaries of measured areas. Openings or wants which are at the boundaries of measured areas shall always be the subject of deduction irrespective of size.
4.7
A dimensioned description for an item in the bill of quantities shall define the item and state all the dimensions necessary to identify the shape and size of the item or its components.
3.5
The requirement to measure separate items for widths not exceeding stated limit shall not apply where these widths are caused by voids. a
IS
5.
Drawn information
5.1 Location drawings: (a) Block Plan: shall identify the site and locate the outlines of the building works in relation to a town plan or other context. (b) Site Plan: shall locate the position of the building works in relation to setting out paints, means of access and general layout of the site. (c) Plans, Sections and Elevations: shall show the position occupied by the various spaces in a building and the general construction and location of the principal elements.
(d) Work carried out in or under water shall be so described stating whether canal, river or sea water and (where applicable) the mean Spring levels of high and low water. (e) Work carried out in compressed air shall be so described pressure and the method of entry and exit. stating the
8.
5.2 Component drawings: shall show the information facture and assembly of a component.
8.1 Method of fixing shall only be measured and described where required by the rules in each Work Section. Where fixing through vulnerable materials is required to be identified, such materials are deemed to include those listed in rule 8.3 (e).
necessary
for manu-
8.2
Where the nature of the base is required to be identified each type of base shall be identified separately.
5.3
Dimensioned diagrams: shalt show the shape and dimensions of the work covered by an item and may be used in a bill of quantities in place of a dimensioned description, but not in place of an item otherwise required to be measured.
8.3
Where the nature of the background is required to be identified description shall state one of the following: the item
5.4
Schedules which provide the required information drawings as required under these rules. shall be deemed to be
(a) Timber, which shall be deemed to include manufactured building boards. (b) Masonry, which shall be deemed to include concrete, brick, block and stone. (c) Metal. (d) Metal faced materials. (e) Vulnerable materials, which shall be deemed to include glass, marble, mosaic, tiled finishes and the like.
6.
6.1 A precise and unique cross-reference to a catalogue or to a standard specification may be given in an item description instead of the description required by rules 2.6 and 2.12 or instead of a component drawing.
7.
9.
Composite items
(a) Work on or in existing building - see general rule 13. (b) Work to be carried out and subsequently orary works). (c) Work outside the curtilage of the site. removed (other than temp-
9.1 Notwithstanding the requirement of clause 4.2, work to be manufactured off site may be combined into one item even though the rules require items to be measured separately, provided the items in question are all incorporated into the composite item off site. The item description shalt identify the resulting composite item and the item shall be deemed to include breaking down for transport and installation and subsequent reoasse mbly.
10. Procedure where the drawn and specification inf·ormation required by these rules is not available
10.1 Where work can be described and given in items in accordance with these rules but the quantity of work required cannot be accurately determined, an estimate of the quantity shall be given and identified as an approximate quantity. 10.2 Where work cannot be described and given in items in accordance with these ru les it shall be given as a Provi sional Su m and identified as for either defined or undefined work as appropriate. 10.3 A Provisional Sum for defined work is a sum provided for work which is not completely designed but for which the following information shall be provided: (a) The nature and construction of the work. (b) A statement of how and where the work is fixed to the building and what other work is to be fixed thereto. (c) A quantity work .. or quantities wh,ich indicate the scope and extent ot the and the like identified in Section A35.
= =
:;
rn3
mm
or
kg I h pcsum provsum
= = = = =
:;
tonne hour Prime Cost Sum Provisional exceeding equal to or exceeding not exceeding less than percentage Sum
10.4 Where Provisional Sums are given for defined work the Contractor will be deemed to have made due allowance in programming, planning and pricing Preliminaries. Any such allowance will only be subject to adjustment in those circumstances where a variation in respect of other work measured in detail in accordance with the rules would give rise to adjustment. 10.5 A Provisional Sum for undefined work is a sum provided for work where the information required in accordance with rule 10.3 cannot be given. 10.6 Where Provisional Sums are given for undefined work the Contractor will be deemed not to have made any allowance in programming, planning and priCing Preliminaries.
> >
< < %
=
::::
12.2
Cross references within the classification Work Section number Example: Number from first column Number from second column tables are given in the form: Number from third column Number from fourth column
020: 2. 2. 2. 1
Excavation and filling Excavating To reduce levels Maximum depth < 1.00m Commencing level stated ground level.
where
12.3 An asterisk within a cross reference represents all entries in the column in which it appears.
12.4
The digit 0 within a cross reference represents which it appears. no entries in the column in
13.2
The additional rules for work to existing buildings are to be read in conjunction with the preceding rules in the appropriate Work Sections. 13.3 A description of the additional Preliminaries/General conditions which are pertinent to the work to the existing building shall be given, drawing attention to any specific requirements due to the nature of the work.
A Preliminaries/General conditlons
INFORMATION PROVIDED
Pl Location drawings as defined ill General Rule 5.1
II
SUPPLEMENTARY INFORMATION
MEASUREMENT RULES
DEFINITION RULES
01 A fixed charge is for work th e cost of which is to be conside red as independent of duration 02 A ti me related charge is tor work the cost of which is to be considered as dependent on du ra~on
COVERAGE RULES
C 1 Works of a temporary nature are dee med to include rates, lees and charges related thereto in Sections A36, A41 , A42, and A44
P2 Information to facilitate visiting site and addresses where drawillgs or other information additional to that required by Ihese rules or other listed information may be inspecled
CLASSIFICATION TABLE
item
3 Total heig ht
3 Detaits of related work by others
Mt Given onry when the equiv al ent information is not indicated on the drawings provided
item
sectons
7 Others
Preliminaries/General
conditions continued MEASUREMENT RULES DEFINITION RULES COVERAGE RULES SUPPLEMENTARY INFORMATION
CLASSiFICATION TABLE
1 Fixed cha.rge
2 nme related charge
item
and stall Includes management, trades supervision, engineering, programming and production, quantity surveying support staff and the like
03 Management
D4 Site accommodation inCludes offices, laboratories. ca~ns, stores, compounds, canteens, sanitary fadfities and the ijke
05 Ilems listed are not e)(haustive and are for convenience of pricing only
C3 General attendance is deemed to inClulla the use of the COlllracto(s temporary roads. pavings and paths, standing scaffold ing. 3tanding power operated hoisting plant the provision of temporary lighting and water supplies. clearing away rubbish. provision 01 space for the sub-contractor's own offices end the storage of his plant and materials and the use of messrooms. sanitary atcommodation and welfare facilities provided by the Contractor C4 General attendance. where the Joint Fire Code applies is detmed to in~lude hand bells, whistles. klaxons, manualiV operated sounders, security guards, fire· signage 18.g. location of fire access routes and positions of dry riser inlets end fire e~ting~jshersl. fire doors and fire stopping to lift-shafts. service ducts and voids. water supplies for fire fighting equipment and the services at an appropriate number of Fire Marshalls where the works are a ~rge project
fD
MEASUREMENT RULES DEFINITION RULES COVERAGE RULES SUPPLEMENTARY INFORMATION
07 Items listed are not exhaustive and are tor convenience 01 pricing only
etc,
2 Main contractors protrt 3 Main cDnlractDr's overheads 4 Special attendance, details stated 1 Scaffolding 2 Accessroads 3 Hardstandings 4 Positioning 5 Storage 6 Power 7 Temperature and humidity 8 Others
% % ilem 1 Fixed charge 2 Time related charge 08 Scaffolding under this rule is special scaffolding, scaffolding additional 10 the Contractor's standing scaffolding, or standing scaffolding required to be a~ered or retained D9 Positioning includes unloading, distributing, hoisting and placing in position giving in the case of significant Hems the weight and/or size and position relative to ground level or other datum Fixing only such items is deemed to include unloading, storing, hoisting the goods and materials and returning packaging materials to the nominated supplier carriage paid and obtaining credits therelor Dl0 Work by statutory authorities includes work by publk: companies responsfble lor statutory work when executi ng their statutory duty
C5
51 Particulars of any costs to be paid of conveying goods and materials to the site and/or of any special packing or similar requirements
A53 Work
by statutory authorities/undertakers
1 Work by the local authority 2 Work by statutory urnlertakers prov sum
ASS Dayworks
1 Oaywollls 1 LabOur 2 Ma.tefials 3 Plant prov sum
C Existing site/buildings/services
C20 Demolition
C21 Non-Hazardous and Hazardous material removal
MEASUREMENT RULES
Ml The rules within this Section apply to works to existing buildings as defined in the General Rules
DEFINITION RULES
COVERAGE RULES
SUPPLEMENTARY INFORMATION
CLASSIFICATION TABLE
1 Demolishing all slructures 1 Description sufficient for identification 1 Levels to which structures are demolished item 1 Materials remaining the property of the Employer 2 Materials for re-use 3 Making good structures 4 Leaving parts 01 existing walls temporarily in position to act as buttresses 5 Temporarily diverting, maintaining or sealing off exisling services 6 Non-hazardous material 7 Hazardous material 4 Support 01 structures not to be demolished 5 Support of roads a nd tire like 1 Position and type of shoring and nature of slruciure or road to be shored stated item 1 Providing and erecti ng 2 Maintaining. stated duration M2 Only temporarily diverting, maintaining or sealing off existing services is measured under this rule Dl Materials arising from demolitions are the property of the Contractor unless otherwise stated Cl Demolition items are deemed to include: (a) disposal 01 materials other than those remaining the property 01 the Employer or those for re-use (b) temporary support incidental to demolitions which is at the discretion 01 the Contractor SI Method of demolition where by specific means S2 Setting aside and storing materials remaining the property of the Employer or those lor re-use S3 Employer's restrictions on methods of disposal of materials
03
3 Adapting, details stated 4 Clearing away 5 Cutting holes in the structure. details stated
6 Temporary roofs
7 Temporary screens
item
INFORMATION PROVIDED
PI The following informa1ion is shown either on location drawings under A Preliminaries/General conditions or on further drawings which accompany the bills of quantities: (a) the scope and location of the work relative 10 the exi~ting layout indicating the existing structure
DEFINITION RULES
01 Materi als arising are the property of the Contractor unless otherwise stated 02 locations stated relative to the existing building
COVERAGE RULES
Cl Shoring and scaffolding incidenlal to the work and making good atl work disturt>ed by such shoring and scaffolding is deemed to be included C2 Wolllto existing buildi ngs ~ems are deemed to include: (a) disposal 01 materials other than those remaining the property of the Employer or those for re -use (b) incidenta.1 wolll which is at the discretion of the Contractor (c) atl new fixing or joining materials required
SUPPLEMENTARY INFORMATION
SI Melhod of operation, where by specific means S2 Setting aside and storing materials remaining the property of the Employer or those for re- use 53 Employers restrictions on methods of disposal of materials
CLASSIFICATION TABLE
1 Cuning out defective concrete and replacing with new 1 0 imen sioned description 1 Plain, delails stated 2 Reinforced, details stated 3 Gun applied, details staled m1 m 1 T reatment 01 reinforcement, details staled 2 Anchored mesh reinforcement, details staled 1 Centres of drilling holes 2 Removing existing finishes
---
nr
1 Dimensioned
description
ml
--
nr
--
m1
--
nr 4 Repainting 1 Size and depth 01 raking out of existing joint 1 Brickwork, details stated 2 Siockwork, details stated
--
1 Making good with materials other than to match existing, details stated
m2
- --
1 Type of painting
m
- --
S7 Composition mortar
and mix of
nr
CLASSIFICATION TABLE
5 Removing stains and the like (or) 1 > 1.00 m2 2
:0:;
MEASUREMENT RULES
I Concrete
DEFINITION RULES
COVERAGE RULES
SUPPLEMENTARY INFORMATION
Special cleaning rnaierials
m2
t--
1.00 ffi2
2 Brickwork 3 Blockwork
4 Stonework
nr
sa
6 Cleaning surfaces
1 Facings
m2
S9 Cleaning materials
nr
M4 Inserting new wall ties is measured here only when executed without demolition
1 Detailed description and size of new profi Ie 2 Detailed description and length and size 01 new p!'ofile
r-nr
9 Artificial weathering
m'
1 To match existing
C45
INFORMATION PROVIDED
PI The following information is shown either on location drawings under A Preliminaries/General
conditions or on further drawings which accompany the bills 01 quantities: (a) 1he scope and location of the work relative 10 the existing layout indicating the existing structure
SUPPLEMENTARY INFORMATION
51 Me1hod of operation, where by specific means S2 Damp proof chemicals
CLASSIFICATION TABLE
1 Chemical damp proof courses 2 Injection mortar damp proof courses 3 Inserted mecllanical damp JlIoof courses 1 Brickwork 2 Btockwork 1 Thickness of wall stated m 1 Centres 01 drilling holes 2 Removing existing finishes
3 Stonework
COO Repairing/RenovatinglConserving
C51
INFORMATION PROVIDED
metal timber
MEASUREMENT RULES
conditions or on further drawings
DEFINITION RULES
COVERAGE RULES
SUPPLEMENTARY INFORMATION
CLASSIFICATION TABLE
1 Repairing metal 2 Repairing limber 1 Dimensioned description m'
--
MI The dimensioned
description or dimensioned diagram (in conjunction with the Information Provided) must clearly idenfity all work in exploration, preparaton and execution together wilh Ihe associated works required
or
nr
--
SI SUCh inlormation as is appropriate to the repair. renovation or refurbishment of Iheitam S2 Such informatioo as ~ appropriate to the trealment 01 umber to eradicate fungus attacks or beetle infestation
ego
INFORMATION
Pl The following information is shown either on locabon drawings under A PreliminariesJGeneral conditions or on lurther drawings which accompany the bills of quantities: (a) the scope and location of the work relative to the existing layout indicating the existing structure
Ml The ru les within this Seelion apply to works to existing buildings as defined in the General Rules M2 Any operaton to existing buildings involving removal of existing materials (other Ihan for bonding purposes or renewal) is measured within this Section
Dl Materials arising from alterations - spot items are the property 01 the Contractor unless otherwise slated D2 Location is stated relative to existing build iog
Cl Shoring and scaHoh:ling incidental to the work and making good all wolll disturbed by such shoring and scaffolding is deemed to be included within each ite m C2 Alterations' spot items are deemed to include: (a) disposal of materials other than those remaining the property of the Employer or those lor re-use (b) work incidentallo a~erations - spot items which is at the discretion at the Contractor (e) all new fixing or joining materials required
CLASSIFICATION
TABLE
1 Removing fittings and fixtures 2 Removing plumbing and engineering installations 3 Removing finishings 4 Removing coverings 5 Cutting openings or recesses 6 Cul1ing back projections 7 Cutting to reduce thickness 8 Filling in openings 9 Temporary roofs
1 Delails sufficient for identificaton stated 2 Dimensioned description sufficient tor idenmication including type and thickness of existing structure
item
1 Making good structures 2 Extending and making good fi nishings 3 Inserti ng new work, details stated 4 Non-hazardous material
M3 Details stated for inserting new work are the equivalent of those details required by lhe rules for the measurement 01 the same in other wolll sections
D3 Inserting new work includes re·fixing or re-using removed materials D4 All male rial is deemed to be inert unless otherwise described
5 Hazardous material
item
1 Providing and erecting 2 Maintaining, duralion slaled 3 Adapting. details stated 4 Clearing away 5 Disposing 01 rainwater, details staled 6 Providing openings, detai Is stated
~0 Temporary screens ,
D Groundwork
020 Q20
INFORMATION PROVIDED
PI The following information is shown either onocancn drawings under A Preliminaries/General conditens or on further drawings whiCh accompany the bills 01quantities or slated as assumed: (a) the ground water level and the date when it was established, defined as the pre-contract water level (b) the ground water level is to be r·e~established at the time each excavation is carried out and is defined as the post contract water level (c) ground water levels subject to periodic changes due to tidal. or similar effects are so descdbed giving the mean high and low water levels (d) details 01 trial pits or boreholes including their location and the SOil Investigation Report together with the chemical a nalyses there of tro m which the inert, 11oil-hazard 0 usa 11d hazard 0 us mate ri a I elas s ilications ca n be deterrn i ned (e) features retained
(I) live over or underground services indicating location (g) pile sizes and layout in accordance with Sections D30 - D32 where applicable
CLASSIFICATION TABLE
1 Site prepara~on
1 Removing tfees
III
m. girth
MI Tree girths are measured at a height 01 1.00 m above grou nd M2 Stump girths are measured at the top
C 1 This worlds deemed to include: (a) grubbing up roots {b) disposal 01 materials (c) tilling voids Dl Site vegetation is bushes, scrub, undergrowth, hedges and trees and tree stumps s 600 mm girth
m2
ml
2 Excavating
ml m1
M3 The quantities given are Ihe bulk before excavating and no allowanoe is made for subsequent varia~on s 10 bulk or for extra space for working space or to accommodate earthwork support M4 Excavaling for grou nd beams not between piles is measured under 2.5 s 6.*.*
D2 All male rial is deemed to be inert un les s ot herw ise described D3 Not used
e
3 Items ext ra over excavating in inert material irres pectlvs 01 dept n
To bench sloping grou nd to receive filling m1 1 Excavating below ground water level
3 Hazardous male rial 4 Next existing seNiCes 5 Around existing services crossing excavation 4 Breaki ng out existing materials 5 Breaki ng out existing hard pavings, thickness stated
-rn
t Rock 2 Concrete
mJ
I-ml
Reinforced concrete
05 Rock is any material which is 01 such sire or ~sition that it can only be removed by wedges. special plant or explosives
5 Coated macadam or
asphalt 6 Working space allowance 10 excavatons 1 Reduce levels, basements and the like 2 P~s 3 Trenches 4 Pile caps and ground beams between pi les ml M7 Working space is measured where the face of the exca vaton is < 600 mm from the face of tormwork., re ndering, tanking or protective walls Me The area measured is calculated by mu Iliplying t~e girth at the tormwork, rendering, tanking or protective walls by the depth of excavation below the commenci ng level 01 the excavaton
06 Backfilling with special materials occurs where selected or trested excavated materials or im~ned materials are used
C2 Additio nal earthwork support, disposal, back!i Iling, work below ground water level and breaking out are deemed to be included
Ell
MEASUREMENT RULES
1 Curved
2 Below ground water level 3 Unstable grou nd 4 Next to roadways M9 Earthwork support is measured the lull depth to all faces 01 excavation whether or not required except to (a) tace s 0,25 m high (b) sloping faces of excavations where the angle of inclination is ::; 45° from the horizontal (c) faces of excavations which abut existi ng walls, piers, or other structures Ml0 Earthwork support below ground water level or in unstable ground is measured from the commencing level of the excavation to the full depth M1t Earthwork support below ground water level is only measured where a corresponding Item is measured in accordance with 3. t .0.0 a fld is adjusted accordingly if the post contract water level is diHerent
DEFINITION RULES
07 Earthwork support is deemed to mean providing everything to uphold the sides of excavation by means other than interlocking steel piling which is measured in Section 030 08 Earthwork support next to madways occurs wnere the horizontal distance from the face supported to the edge of the roadway or footpath is < the depth of the excavated face below the bottom of the foundations 09 Earthwork support next to existing buildings occurs wnere the horizontal distance from the lace suppo rted to the nearest part of the foundations of tm. bui Iding, is < the depth of the excavated face oolow the bottom of the foundations 010 Unstable ground is running silt. running sand, loose gravel and the like
COVERAGE RULES
C3 Curved eartt,work supporJ is deemed to include any extra costs of curved
SUPPLEMENTARY INFORMATION
s 2,00
excavaton
3 Distance between
opposing faces> 4,00 m
8 Disposal
ilem
M12 An ilem for disposal of ground water is onty measured where a corresponding item is measured in accordance with 3,1, and is adjusted accordingly if the post contract water level is different 1 Specified locations, detal Is staiec 2 Specified handling, details staled 3 Non-hazardous material M13 The Quantity given for disposal is the bulk before excav ali ng and no allowa nee is made for subsequent variations to bulk or for extra space to accommodate eanhwork support
011 Surface water is wa ter 0 n the surface of site and the excavations
3 Excavated material
1 Olfsite
m3
2 On sile
4 Hazarcous material
~
9 Filii ng to excavations 10 Filling
to make
up levels
' I Arisi ngiro m the excavations 2 Obtained from on site spoil heaps 3 Obtained off site, type stated
m'
MI4 Fitting is measured as equal to the void fill·ed MI5 The average Illi ckness measured for fiffing is that afte r com paction MI6 The positon 01 external planters and the like is only stated where not at grou nd level
C5 Filling arising from Ihe excavations is deemed to include multiple Ilandling at me contractors discretion
ml
13 Su nace treatments
I
I Applying herbicides
I-m'
2 Compacting
1 Ground 2 Filling
S7
Melhod of C{)mpacting
3 Bottoms of excavations
3 Trimming
I Siopi ng su rrace s
1 Battered
2 Vertical 3 In rock
3 Sides of embankments
59 Method 01 preparing
030
Piling
MEASUREMENT RULES
conditions or on further drawings
III
DEFINITION RULES COVERAGE RULES SUPPLEMENTARY INFORMA liON
INFORMATION PROVIDED
PI The following information IS shown either on location drawings under A Preliminaries/General which accompany the bills of quantities (a) the genera.1piling layout (b) the positions of different types of piles (e) the positions of the work within the site and 01 existing services (d) the relabonship to adjacent buildings
P2 Soil description: (a) the nature of the ground is given in accordance with Section 020 Information Provided (b) where work is carried oul near canals. rivers. etc. or tidal waters, the level of the ground in relation to the normal levels of the canal or river etc. or to the mean Spring levels of high and low tidal waters. is stated; flood levels are stated where app"cable P3 Commenong levels: (a) the levels from which the work is expeCted to begin and from which measurements have been taken are Slated; irregular ground is so described
nr
3 Total bored
m
m
M1 Bored and driven lengths are measured along the axes of the piles from the commencing surface to the bottom of the shafts of bored pi les and to the bottom of the casings of driven piles I------------i M2 Pre-boring is only measured where it is specifically reQuired
01 Piles comprising a driven light gauge casing which is first Ii lied with concrete and then withdrawn are classed as driven shell pi les where the piles are designed for the load to be carried OIl the co ncrete 02 Filling such piles is not
classed as filling hollow piles in accordance with Section
CIT otal concrete length is deemed to include concrete placed in excess of the completed length C2 Pre-boring is deemed to include grouting up voids between sides of piles and bores
S2 Tests of materials
S3
Type of grout
S4 Details 01 compaction
030.20.1··
M3 Breaking through obstructions is only measured where obstructions are encountered above the founding stratum of the pile C3 The work is deemed to include work below the specified bottom
2 Enlarging bases for bored piles 3 Enlarging bases lor driven shell piles
1 Diameter of enla.rged
base stated
nr
6 Permanent casings
C4 Permanent casi ngs are deemed to include driving heads and shoes
S5 Type of material and finish to external surface S6 Details 01 driving heads and shoes where not at the discretion of the Contractor
1 Totallenglh
1 Tops of permanent
casings
is deemed Ie include
preparabon and integration of reinforcement into pile cap or grou nd beam and disposal
8 Reinforcement to piles
C6 Aeir.lorcement to piles is deemed to include tying wire, spacers, links and binders which are at the discretion of the Contractor
9 Disposal
1 Excavated materials
sialed
3 Non-hazardOUS material 4 Hazardous material
10 Delays
1 Rig standing
f----
11 Pile tests
1 DetailS stated
or
sa
tests
030
continued
MEASUREMENT
1 Total number driven. speci fied length and com mencing su rf ace stated 2 Total driven depth nr t Preliminary piles 2 Raking. inclin alio n staled
RULES
DEFINITION RULES
COVERAGE RULES
SUPPLEMENTARY INFORMATION
S9 Kind end quality of materials S10 Tests of materials Sl1 Details of driving heads and shoes
M8 The measurement for the total driven depth includes for driving e)(lended piles M9 The driven depth is measured from the commencing surface to the bottom of the pile toe along the axis of the pile
04 The total driven depth is C8 Driving. heads and that specifically required by shoes ere deemed to be the designer included
1 Redriving piles
nr
M10 Reddving piles is only measured where it is specifically required MIl Pre-boring is only measured where it is specifically required
1B Pre-boring
C9 Pre-boring is deemed to include grouting up voids between sides of piles end bores
19 Jetting 20 Filling hollow piles with concrete 1 Plain m m nr m CIO Preparing heads, to receive pile extensions is deemed to be included S13 Specification 01 concrete end reinforcement
21 Pile extensions
",
1 Total length
C11 Cutting off tops of piles is deemed to include prepration and integration of reinforcement into pile ca p or ground beam and disposal M12 The volume of disposal 0.1 surplus excavated materials is calculated from the nominal cross-sectional size of piles and their depths measured in accordance with 12-16.1.1 and 2." 05 All material is deemed to be inert unless otherwise described
23 Disposal
1 Excavated material
1 Off site
ml
2 On site
1 Special locations. details stated 2 Specified handling. details stated 3 Non -nazaro 0us mate riaI 4 Hazardous material
24 Detays
1 Rig standing
tests
MEASUREMENT RULES
M14 The measurement of the total driven depths includes for driving extend ed pile s MI5 The driven depth is measured from the c ommen c inII surfa ce to the bottom of the pile toe along the axis of the pile MI6 The following separate items are required for each group of interlocking piles: (a) one or more items for the tota I area of th B group of piles divided into the ranges of specified lengths given in 27.1.1-3.~ (b) an item for the total driven area of the group of piles M17 The areas of items fo r inteno ckin 9 piles are calculated by multiplying the mean undeveloped horizontal lengths of the pile walls formed (including lengths occupied by special piles) by the depth s measured in accordance with the definllons of driven depths in the case of items for the driven areas and by the lengths measured in accordance with the definition of lengths in the case of items for the specified areas of piles
DEFINITION RULES
COVERAGE RULES
SUPPLEMENTARY INFORMATION
S15 Kind and quality of materials S16 Tests of materials
e13 The cost of extra ction is deemed to be included with piles so described
I Total area of specified length'" 14.00 m 2 Total area of specified laflgth 14.00- 24.00 m 3 Total area of specified len gth > 24.00 m 4 Total driven area
m'
ED
D30 continued CLASSIFICATION TABLE
28 Items extra over interlocking piles I Comers 2 Junctions 3 Closures 4 Tapers 29 Isolated pile extensions 1 Mass per metre and cross-sectional size, or section reference stated 2 Seetion moduIIIs and cross-ss ctio naI size. or section referen c B stated 1 Mass per metre and eross-seenonat SIze, or sE!ction reference stated 2 Section modulus and cross-sectional size, or section reference stated 32 Cutting interlocking piles to form holes 33 Delays 1 Dimensioned description 1 Ri9 sta nding 1 lsnlated piles 2 Inte rloc king pil es 34 Pile tests 1 Details stated nr 1 Total number 2 Extension length s 3,OQm 3 Extension length> 3.00m nr m I Preliminary piles 2 Raking, inclination ratio state d 3 To be extracted 4 Using materials arising from ctltting off 511 fill us len 9ths 01 other piles 1 Isolated piles (nr] m , Preliminary piles 2 Raking, inclination ratio stated 2 Interlocking piles (nr) m M20 The length measured is the surplus length of each pile MI9 Separate items are required for the length of pile extensions and for the number of pile extensions C14 The cost of extraction is deemed to be inel uded with piles so described CI5 Pile extensions are deemed to include tile work necessary to attach the extension to tile pile I Type stated m
MEASUREMENT RULES
MIS The length measured for items extra over is the totallen9til
DEFINITION
RULES
COVERAGE RULES
SUPPLEMENTARY INFORMATION
CI6 Cutting off surplus from specified lengths of piles is deemed to include provision and filling of working space and disposal
nr
CI7 Delays are deemed to include associated labour S17 Timing and details of tests
MEASUREMENT RULES
on further drawings M 1 Piled walls are measured in accordance with Section
DEFINITION RULES
COVERAGE RULES
SUPPLEMENTARY INFORMATION
030
P2 Soil description: (a) the nature ollhe groond is given in accordance with Section D20 Inlormation Provided (b) where work is carried out near canals, rivers, etc. or tidal waters, the level of the ground in relation to the normal level of tlle canal or river etc. or 10 the mean Spring levels of high alloj low tidal waters is stated: flood levels are stated where applicable P3 Commencing levels: (a) the levels from which the work is expected to begin and from which msasuremerns (b) irregular 9found is so described have been taken are stated
2 Items extra over excavating in inert material and disposi ng the reot
1 Non-Ml(Ifdous
material
m)
1 Rock 2 Concrete 3 Reinforced concrete 4 Brickwork. blockwcrk 0 r stonework 5 Coated macadem or asphalt M3 Concrete volume is measured net except that deductions are not made far the following: la) reinforcement Ib) steel sections of areas s ld) voids .. 0.05 m'in volume
Ie) cast in accessories
4 Breaking out existing hard pavings, thickness stated 3 Ba ckf IIing empty fre neh 4 Concrete 1 Type of IiII rnate rial stated 1 Thickness of wall staled
-m' mo
-
0.50 m'
m1
MEASUREMENT RULES
M4 Reinforcement is measured in accordance with Section E30 and the mass measured includes that of stiffening, lifting and supporting steel cast in where specifically required
I---
DEFINITION RULES
COVERAGE RULES
SUPPLEMENTARY INFORMATION
Cl Cutting oft to specified level is deemed to inc Iude provision and filling of working space and disposal
1 Oetails stated
I-
OJ'
M5 Waterproofed joints are only measured where they are specifically required M6 The lengths measured for guide walls are those of the diaphragm walls M7 The extent to which excavation. disposal. support, concrete, reinforcement, formwork, and the like are to be includ ed is stated in th II item description C2 Preparing cast in pockets or chases is deamed to include fe moving formwork and preparing cast in reinforcement
9 Guidewalls
I limitations on design
and construction stated
t-1 Prepa ring cast in pockets or chases at [unctiens, details stated item
2 Excavating temporary backfill J Removal of guide walls lOne side 2 Both sides 11 Oelays I Rig standing
Im' MB The Iengths mea sured fo r guide wa Us are those of the diaphragm walts M9 DelaVs are onlv measured where they are specifically authorised
C3 Removal of guide walls is deemed to include disposal C4 Delays are deemed to include associated labour
12 Tests
1 Details staled
I----nr
041
INFORMATION
MEASUREMENT RULES
on further
DEFINITION RULES
COVERAGE RULES
SUPPLEMENTARY INFORMATION
PI The following information is shown either on location drawings under A Preliminaries/General conditions drawings which accompany the bills of quantities: {a) The relative position of crib walls, gabions and earth reinforcement
CLASSIFICATION TABLE
I Crib walls I Thic kness stated 1 Flat undeveloped area m' 1 Vertical 2 Battering 3 Curved on plan Ml No deductions are made for openings within crib walls which are part of the modular system, nor for openings", 1.oom' Cl Crib walls are deemed to include dowels and pins, granular infill and compaction, special units, forming ends and comers, obtaining and providing manufacturer's certificates and for building in pipes and forming small openings C2 Gabion baskets are deemed to include assemblng, tying and fixing and bracing and tying lids 1 Selected, details started 2 Treated, details started 3 Specified handling, details started 4 Earth reinforcement 1 Fabric 1 Mesh refe rence m' 1 Flat 2 Sloping 3 Curved on plan M4 No deductions are made lor voids", I,oom' in area M3 The area measured for earth reinforcement excludes laps. C4 Earth reinforcement is deemed to include assembling, tying, fixing, stacking and tensioning S2 Minimum laps M2 filling is measured Ih e nett vol urnII of the basket C3 filling is deemed to include compaction and overfilling
2 Gabion baskets
1 Dimensioned description
Nr.
m'
050
Underpinning
MEASUREMENT RULES
conditions or on further drawings
II
DEFINITION RULES COVERAGE RULES SUPPLEMENTARY INFORMATION
INFORMATION PROVIDED
PI The following information is shown either on location drawings under A Preliminaries/General which accompany the bills of quandlies (a) the location and extent of the work (b) details of the existing structure to be underpinned
P2 Information regarding the nature of excavation work is described in accordance with Section 020 Information Provided
P3 The limit of length carried out in one operation and the number of secaons the Contractor is permitted to undertake at one time
CLASSIFICATION TABLE
1 T empor ary support lor
existing stnuctures I Particu lar requirements staled I Preliminary trenches 1 Maximum depth -:; 0.25 m 2 Maximum depth s 100 m item SI DetaHs ot making good
2 Excavating
ml
2 Underpinning pits
3 Maximum depth
s 2.00
Ml Wid1h allowances are relaled to the total depth of excavation measured from the top or the preliminary trench to the base of the underpinning pit as follows: (a) 1 m where the total depth is ~ f ,5 m (b) 1.5 m where the total depth is 1.5 ~ 3m (c) 2 m where Ihe total depth is > 3 m
M2 The width of a preliminary trench is calculated as the sum 01 any projection of Ihe retained foundation beyond the face of the wall plus any projection of th e underpinning beyond the face of the retained foundation plus the width allowance M3 The width at an u nderpinn ing pit is calculated as the sum of the width of retained toundation plus any projection of the underpinning beY0rld the face of the retained foundation plus the width allowance
01 Preliminary trenches
extend down to the underside of existing foundations
02 Underpi nning pits extend from Ihe underside of existing foundations down to the base of the underpinning excavation
M4 Items extra over are measured in accordance with Section D20:3~5. '*.
*. *
1 Preliminary trenches
2 underpinning pits
m1
M5 Earthwork support is measured in accordance with Section 020:7.*.*.* M6 Earthwork support to underpinning pits is measu red to the back. front and both ends of the underpinning pits and also between each section of Itle underpinning
M7 Disposal of water and excavated material are measured in accordance with Section 020:8.*.*.* M8 Filling is measured in accordance with Section 0209 & 10-*-*.* M9 Surface treatments are measured in accordance with Section 020:13.*.'-1<-. * M 10 Concrete, lormwork, reinforcement, brickwork and tanking are measu red in accordance with the appropriate Work Sections
8 Filling
9 Surface treatments
IS
MEASUREMENT RULES
M1 Concrete volume is measured net except that deductions are not made lor the following: (a) reinforcement (b) steel sections of area S 0,50 m2 (c) cast iII accessories (d) voids S 0,05 mJ in volume (except voids in troughed and coffered slabs)
DEFINITION RULES
COVERAGE RULES
C 1. Concrete is deemed to include finishing as struck from basic finish formwork Of with a non- mechanical tamped lin ish unless otherwise required under worked finishes
SUPPLEMENTARY INFORMATION
51 Kind and quaUty 01 materials and mix details 52 T esls of malerials and finished work Measures watertightness
sa
to achieve
CLASSIFICATiON TABLE
1 Foundations 2 Ground beams
m3
1 Reinforced
2 Reinforced> 3 Sloping S 15° 5%
recesses
M3 The th ickness range stated 01 collered and trough ed slabs is measu red overall
s 150 mm
Slabs slabs
03 Beds inc1ude:
(a) blinding beds (b) plinths (c) thidlenings 01 beds
1 Reinforced 2 Reinforced>
5%
04 Slabs include: (a) allached beams and beam casings whose depth is s three times their width (depth measured below Itle slab) (b) column drop heads
05 Collered and troughed slabs incfude margins whose width is S 500mm_ Wider margins are included with ordinary slabs 06 IWal1s include attached columns and piers
f---m1
13 Staircases
M4 Columns iIre only measured as such when isolated and when their lenglh on plan is s lour ~mes their thickn ess
07 Deep beams and beam casings are those whose depth (measured below the slab where anach ad) is ~ three times 1M eif width DB Staircases inelude landi ngs and strings
14 Upstands
m'
1 Top surlace sloping,,; 15° 2 Top surtaee sloping ~ 15°
16 Grouting
nr
f---------;
17 Filling
1 Mortices
2 Holes, (nr)
I
3 Chases ~ 0.01 m2
4 Chases
$;
o.oi
m2
ED
MEASUREMENT RULES
DEFINITION RULES
COVERAGE RULES
SUPPLEMENTARY INFORMATION
CLASSIFICATION TABLE
1 Slabs 1 Thickness staled 1 Tops 2 Soffits 2 Walls 3 Beams 4 Columns m' 1 Curved Ml Reinforcement is measured in Section E30 51 Kind and quality of materials 52 Preparato ry work
E20
INFORMATION PROVIDED
PI The following information is shown either on location drawings under A Preliminaries/General which accompany the bills of quantities: (a) the relanve positions of concrete members (b) the size of members (c) the thickness of slabs (d) the permissible loads in relation to casting times
DEFINITION RULES
01 Plain formwork surfaces
COVERAGE RULES
C 1 Formwork is deemed 10 indude adaptation to accommodate projecling pipes, reinforcing bars and Ihe like C2 FormWOrk is deemed to include all cutting, splayed edges and the like
SUPPLEMENTARY INFORMATION
S 1 Kind and quality of materials and propping requirements for permanent formwork S2 Basic finish where not at the discretion of the Contractor
03 Permanent formWOl'k is
thai which is designed 10 remain in position
CLASSIFICATION TABLE
1 Sides of foundations 1 Plain vel1ieal 1 Height> 1.00 m
f---------+----I
m~ m
1 LeI! in 2 Permanent
2 Dimensioned description
6 Steps in soffits
7 Machine bases and plinths 8 Soffits of slabs 9 Soffits of landings (nr) 1 Slab thid\fless
s 200
mm
m1
2 and thereal!er in 100 mm stages 1 Size of mould and profile. centres of mould. and slab Ih ickness stated
~--------------+-------------~
10 Soffits 01 coffered or troughed slabs
15°
M4 Voids:; 5.00 m1 irrespective of location are not deducted from the area measured M5 Soffits of coffered or lroughed slabs are measured as if to a plain surface M6 The thickness stated of the coffered or troughed slabs is measured overall M7 Top formwork is measu red for su rtaces slopi og > 150 or where otherwise specifically required
06 Formwork to soffits of slabs includes formwork 10 landings occurring at floor levels 07 Soffits of coffered or !roughed slabs include margins which are s 500 mm wide
11 Top formwork
E20 continued
CLASSIFICATION TABLE
12 Wa.lIs 1 Vertical 2 BaHered
II
MEASUREMENT RULES
ml
1 Heig ht >
DEFINITION RULES
D8 Walls include isolated columns and column casings whose length on pi ani s > fa ur tim es thei r th icl\fl ess
COVERAGE RULES
SUPPLEMENTARY INFORMATION
3.00 m above
M8 Voids s 5,00 ml irrespective ouocanon are not deducled from the area measured fa r walls M9 The area measured lor walls whose height is > 3.00 m includes the area below 3.00 m high Ml0 The area of wall kickers is not deducted
1.50 m
3 Left in
4 Permanent
MIl Passings 01 subsid iary beams or 0 Iher projectio ns are not deducted from areas 01 formwork but such intersections are deemed to constitute the commenc-ement of an additional member M12 Formwork to edges 01 suspended slabs associated with attached beams at slab perimeters is included with the measurement of the formwork to such beams M 13 Recesses, nibs or rebates wh ich OCCU r in beam or column lormwork measured in accordance with 13 -16.'1;-,2.-:+' are included in the measurement ot such tormwork
D9 Where a downstand beam is formed by tempor~ry fa rmwork bu t III e slab is supported by permanent formwork the downstand beam IS regarded as an isolated beam Dl(l Regular shaped includes rectangular. circular. hexagonal or other definable regular shape
C3 Formwork 10 beams,
columns and casings is deemed to include ends
1 Dimensioned description
M 14 Recesses, nibs and rebates are only measured as extra over on superficial items of tormwork
C4 Formwork to recesses is
deemed 10 include ends
ml
Dl1 Formed fimshes are those where a fin ish other than a basic finiSh is required
1 Laflin
2 Permanent
1 Plain 2 Dimensioned descriplion 1 Width> 1.00 m 2 Width.,; 250 mm ml m
23
MIS Formwork to wall kickers is measu red a 10 fig th e centre Iine 01 th e wa II and is deemed 10 include both sides
24 Openings in walls
-----------_----2 Dimensioned 26 Mortices 27 Holes diagram 1 Depth"; 250 rnrn m 2 Depth 250 - 500 mm 3 Depth 500 mm - 1.00 m
I
nr
1 R eClangula r 2 Circular
-----------------
E30
INFORMATION PROVIDED
PI The following information is shown either on location drawings under A Preliminaries/General which accompany the bills 01 quantities: (al the relative positions of concrete members (b) the size of members (e) the thickness of slabs (d) the permissible loads in relaton to cas~ng times
DEFINITION RULES
COVERAGE RULES
SUPPLEMENTARY INFORMATION
SI Kind and quality of materialS S2 S3 Details 01 tests Bending reslrictions
on further
drawings
CLASSIFICATION TABLE
1 Bar 1 Nominal size stated 1 Straight 2 Bent 3 Curved t 1 Horizontal, length 12.00 15.00m 2 and thereafter in 3.00 m stages 3 Vertical, length 6.009.00 m 4 and thereafter in 3.00 m stages 4 Links 2 Spacers and chairs 3 Sped al joint 1 Dimensioned description 2 Nominal size and type stated Ml The weight of bar reinforcement excludes surtace treatments and rolling margin M2 The stage lengths in the fourth column are the lengths before bending 01 Horizontal bars include bars sloping s 30° from horizontal 02 Vertical bars include bars sloping> 30° from horizonta.1 Cl Bar reinforcement is deemed to include hooks and tying wire, and spacers and chairs wtlich are at the discretion 01 the Contractor
or
M3 Spacers, chairs and special joints are measured only where they are not at the discretion of the Contractor 1 Bent 2 Sirips in one width, width staled M4 T he area meas ured for fabric excludes laps, M5 Voids S 100 m2 in area are not deducted C2 Fabric reinforcement is deemed to include laps, tying wire, all cutting and bending, and spacers and chairs which are at the discretion of the Contractor C3 Bent fabric reinforcement is deemed to include that wrapped around steel members
4 Fabric
ml
54 Minimum laps
E31
INFORMATION
PI The following information is shown ei1tw on location drawings under A Preliminaries/General which accompany the bills of quanti1ies: (a) the relative positions of concrete members (b) the size 01 members (c) the thicklless of slabs (d) the permissible loads in relation to casting limes CLASSIFICATION TABLE
1 Dimensioned description
nr
1 Composite co nstruction
51 Number, length.
material and size 01 wires in tendons
E40
INFORMATION
conditions
Ml Construction joinls located at ltIe discretion of the Contractor are nol measured m 1 Curved M2 The width or depth of join Is ism easorec over all Ot Plain joints are those which do not require formwork Cl Formed joints are deemed (0 include formwork
1 Dimensioned
description
S2 Details of fillers, waterstops. dowels. backi n9 strips and reinforcement crossing joints S3 Method of application S4 Preparation 01 contact surfaces, cleaners, primers and sealers
r-5 Angles in waterstops 6 Intersections in walerstops nr M3 Angles and intersections are measured only where Ihey are welded or pu rpose made
E41
m
DEFINITION RULES COVERAGE RULES SUPPLEMENTARY INFORMATION
SI Description of finish required and method 01 achieving where not at the discretion of the Contractor
INFORMATION PROVIDED
PI Informanon is shown on location drawings under A Preliminaries/General
CLASSIFICATION TABLE
1 Tamping by mechanical means 2 Power floating 3 Trowelling 4 Hacking 5 Grinding 6 Sandblasting 7 Finishings achieved by other means 8 Cutting chases 9 Cutting rebates 1 Depth s 50 mm 2 Depth 50 -100 mm 3 Depth 100-150 mm 4 Depth> 150 mm, depth staled m 1 Specific width slated 2 Making good 3 In reinforced concrete m2 1 Sloping 2 Falls 3 Crosslalls 4 Soffits
1 Oepth $100 mm 2 Depth 100- 200 mm 3 Depth 200 - 300 mm 4 Depth> 300 rrrn. depth stated
nr
1 Specific cross sectional size stated 2 Making good 3 In reinforced coner ete
M3 Cross sectional size is required to be stated only wh ere there is a Specific cross sectiooal size requirement
E42
INFORMATION
PI The tolklwing inlormation is shown either on location drawings under A Preliminaries/General condi~ons or on further drawings
which accompany the bi 115 qu an~ties: of (a) the relative positions of concrete members (b) the size of members (c) the thk:lmess of slabs (d) the permissibje klads in relation to casting times CLASSIFICATION TABLE
I Dimensioned description
ml m or
--
--
Ml Casl-in accessories are normally measured by number (nr). linear or area measure may be used provided that any appropriate spacing dimensions are given in descriptions
Dt cast-in accessories include anchor bolls, anchor boxes, anchor fixing bolts etc. dowels, column guards and isolated glass lenses. Cast-in accessories exclude remtorcement, tying wire, distance blocks, spacers, chairs, structural steelwork, hollow blocks, filler blocks, permanent formwork, joints and all components around which concrete is cast but which are not fixed by the Contractor
E50 Precast concrete frame structures F31 Precast concrete si lis/I inte Is/copi ngs/features
H40 Glassfibre reinforced cement panel cladding/features H42 Precast concrete panel cladding!features H50 Precast concrete slab cladding/features K33 Concrete/Terrazzo partitions
INFORMATION PROVIDED
Pl The following inlormation is either shown on location drawings under A Prelimina.rieslGeneral which accompany the bilts 01 quantities: la) details 01 precast concrete members showing stressing arrangements (b) lull details of anchorages, ducts, sheath ing and vents (c) the relative positons of concrete members (d) the siza 01 members (e) til a thickness 01 slabs (I) the permissible loads con(ji~ons or on further drawings
ED
MEASUREMENT RULES
DEFINITION RULES
COVERAGE RULES
CLASSIFICATION TABLE
1 Type or name stated 1 Dimensioned description 2 Dimen sioned description (nr) 3 Dimensio ned descn ption I Floor u nits. length stated nr t Reinlorceme nt, datai Is staled 2 Casl-in accessories. detai Is staled Mt Precast unts are normal~ measured by number (m). Linear measurement may be used wh ere the length 01 u nits is at the discretion of Ille Contractor, where the individua I u nits are 01 an identical stand ard length, or where otherwise idenbcal units vary in their length, In these cases the nu moor 01 u nits is stated M2 Where floor units are of the same length they may be measured in square metres and grouped together stating length 2 Ilems extra over the unils on whtch they occur 1 Angles 2 Fair ends 3 Stoolings 4 Others, details slated 3 Joints I Dimensioned prolile description 2 Dimensioned descriptiM 1 Sizes 01 lillin 9 and sealants slated m nr MJ Where units are measu red Iinea r, an gles, fair ends, stooliog$ and Ihe like are enu me ra.ted as ex Ira over the un its M4 Enumerated join Is ma~ be given in the description 01 the precast items in which they occur Ct Precast u nijg are deemed to include moulds, reinforcement, bedd.i ng, fixings, temporary supports, cast·i n accsssores and pretensioning SI Kind and quality of materials and mix details S2 Tests of materials and Iinish ed work
r---m
ml
53 54
S5
Melhods ot compaction and curing Bedd ing and fixing Surface finishes
S7 Ki nd and quality 01
materials
~
nr
E60
1NFORMAT10N PROVIDED
conditions or on further drawings PI The following information is shown either on location drawings under A PreliminarieslGeooral whfch accompany the blll of quantities: (a) details of purpose-made, prestressed concrete members showing stressing arrangements (b) lull details 01 anchorages, ducts, sheathing and vents (c) the relative positions 01 concrete members (d) the sile 01members (e) the thickness of slabs (I) the permissible klads
DEfiNITION RULES
01 Composrte slabs inelude margins::; 500 mm wide, wider margillS are included with ordinary slabs
COVERAGE RULES
Cl Composite slabs are deemed to inelude solid concrete work and filling ends
SUPPLEMENTARY INFORMATION
SI Kind and quality of materials, sizes and spac ngs of planks and blocks S2 S3 Top finish Soffit finish
54 Margins
S5 Formwork
CLASSifiCATION TABLE
1 Composite slabs t Thickness stated m1 1 SkJping s 15° 2 Sklping.> 15° 2 Formw()rk
56 Reinforcement and
preS1!essing arrangements
M4 Formwork to in situ component 01 work is measured in accordance with Sec~on E20 M5 Rei nforcement to in situ component 01 work is measured in accordance with Section E30
3 Reinforcement
F Masonry
F10 F11
INFORMATION PROVIDED
P1 The following information is shown either on location drawings under A Preliminaries/General conditions or on further drawings which accompany the bills of quantities: (a) Plans of each floor level and principal seclions showing the poston 01 and the materials used in the walls (b) External efevations showing the materials used
DEFINITION RULES
01 Thickness stated is nominal thickness unless defined otherwise betow D2 Facework is any wor k in bricks or blocks finished fair 03 Work is deemed vertical unless otherwise described 04 Walls include sk.ins of hollow walls
COVERAGE RULES
C1 Brickwork and blockwork are deemed to include (a) extra materials for curved work r (b) a.11ough and fa.ir wiling Ie) forming rough and lair grooves. throats, monioes, chases, rebates and holes, stops and mitres (d) raking out joints to form a key (e) labours in eaves filling (f) labours in returns, ends and angles (g) centering
52 53
54 55
Type of pointing
CLASSIFICATION TABLE
1 Walls 2 Isolated piers
1 Thickness stated
2 Facework one side, thickness stated 3 Facework both Sides. thickness stated
1 Vertical 2 Battering
m2
1 Building against other work 2 Bo ndi ng to other work 3 Used as formwork. d eta iIs of temporary strutting staled 4 Buildi ng ave rh a nd
3 Isolated casings
4 Ch i mney stacks
M5 Building against other work and bonding to other work is measured where the other work is existing or consists of a dinering material
05 Battering walls are sloping walls with parallel sides 06 Tape ring walls are walls of dimi nishi ng th ickn ess 07 Thickn ess sic led lor tapering walls is mean thickness 08 Isolated piers are isolated walls whose length on plan is $ four times their thickness, except where caused by openings
C2 Brickwork and blockwork bonded to another material is deemed to include extra material tor bonding
5 PrOJections
D9 Projections are attached piers Iwhose length on plan is," four times their thickness), plinths, oversailing courses and the like M6 Arches are measured the mean girth or length on face
6 Arches (nr)
1 Height on lace, thickness and width of exposoo soffit and shape 01 arch stated 1 Th ickn ess stated 1 Siz e on plan, sha pe and overall height stated
ml
scaffolding m' M7 Non brick masonry flue linings are measured in Section F30:1 1.10.0
1 Thickness slated
10 Boiler seating kerbs 11 hems extra over the work in which Uley occur 1 Shape and size stated 1 Specials, di rnensionec description 1 Reveals 2 Angles m m
3 Intersections
12 Closing cavities 1 Width of cavity and method of closing stated 1 Venical 2 Raking 3 Horizontal 13 Facework ornamental bands and the like, type stated 1 Flush 2 Sunk, depth of set back stated 3 Projectj ng, depth of set lorwa rd stated
1 Venical, width slated
2 Raking, width stated 3 Horiz on tal, widl h stated 4 Others, details staled
1 Extra over the work in which the)' occur 2 Entirely of stretchers 3 Entirely of headers 4 Building ove rhand
010 Radii stated are mean rad ii on face 011 Facework ornamental bands and the like are brick· on-edqe bands. brick-on-end bands, basket pattern bands, moulded or splayed plinth cappings. moulded string courses, moulded cornices and the like M8 Facework quoins are measured on the vertical angle 012 Facework quoins are formed with facing brids which diHer in kind or size from the gene raI 1aci ngs S6 Method of JOinbng quoins to brick or blockwork
14 F acework quoins
1 Flush 2 Sunk, depth 01 set back stated 3 Projecting. depth of set forward slated
1 Extra over the work In which they occur 2 Cut and rubbed 3 Rusticated 4 Tile inserts included
MEASUREMENT RULES
1 Dimensioned description
, Vertical
DEFINITION RULES
COVERAGE RULES
SUPPLEMENTARY INFORMATION
S7 Method ollorming sills, threshotds, copings and steps
1 Extra over !he wor1ol in which they occur 2 Buildin9 overhand 3 Set weathering
nr
buttresses 20 Facewor1ol ey blocks k 21 Facewor1ol orbels c 22 Facewor1ol ases to b pilasters 23 Facewor1ol appings to c pilasters 24 Facewor1ol appings to c isolated piers 25 Bonding to existing
1 Thickness 01 new wor1ol
m2
013 This ilem does not include appflcation of materials 10 the wall
F20 Natural stone rubble walling F21 Natural stone ashlar walling/dressings F22 Cast stone ashlar walling/dressings
INFORMATION PROVIDED
PI The following information is shown el1her on location drawings under A Preliminaries/General conditions or on further drawings which accompany Ihe bilts 01 quantities: (a) plans of each floor level and principal sections showing the position of and the materials used in the walls (b) external elevations showing the materials used
MEASUREMENT RULES
Ml Stonewoll<. is measured according 10 mean dimensions
M2 No deductiOn is made for: (a) voids S 0.10 m2 (b) flues, lined flues and flue blocks where voids and woll<. displaced are together S 0.25 m2 M3 Linear and enumerated items shall identify grooves, throats, flutes, rebales, cutting and mortices M4 Curved work is so described with !he radii stated
DEFINITION RULES
01 The thickness staled is the nominal thickness except where deli ned olhe!Wise below 02 Slone dressings are those in walls 01 other materials 03 Dimensioned diagrams are given unless a written description is sufficient for lull clarity 04 WorK is deemed vertical unless othe!Wise described
COVERAGE RULES
CI The woll<. is deemed 10 include: (a) exira. stone for joints (b) extra materials tor curvedwoll<. (e) mortices, (other than linear rtems) holes, stops and amses (d) raking oul joints to form key (e) metal cramps, slate dowels, metal dowels, lead plugs and the like (f) labours in eaves filling (g) labours in returns, ends and a.ngles (h) dressed margins to rubble Wllrk (j) levelling uncou rsed work (k) tempiets and patterns (I) rough and fair square cutting
SUPPLEMENTARY INFORMATION
SI Kind and quality 01 materials and, 101rubble walling, whether of random Or squared stones, buill wtIh or without mortar and where coursed the average height of the courses Of maximum and minimum heights of diminishing course $2 Coatings to backs 01 stones 53 Coatings 10 surface of finished work 54 Cleaning on completion and mix of
55 Composition mortar S6
Type of pointing
57 Method of jointing together and fixing S8 Thickness, mix and colour of !he fad rtg material to cast stonework S9 Stones not set on their natural bed 510 Type and positioning of metal cramps, slates, dowels, metal dowels, lead plugs and the like
F20lF21/F22 continued
CLASSifiCATION TABLE
1 Walls 2 Chimney stacks 1 Thickness stated 1 Venical 2 Battering 3 Taperi ng, one side 4 Taperi ng, both sides
MEASUREMENT RULES m1
1 Blocks> 1.50 m long 2 Blocks> 0.50 ml 3 Slone dressings 4 Faced one side 5 Faced both sides 6 Building against other work 7 Building againsl other battered work 8 Bonding to other work 9 Sunk to entasi s, greatest size stated 10 Plain 11 Sunk t2 Circular 13 Circular -aroul ar 14 Rustk:a!ed or flu ted 15 Used as lormwork, detailS 01 temporary slrut1in 9 slated 16 Wilh sloolinqs (m) 17 Band courses with returned ends (nr) 18 Building overhand M5 Building against othel ' work and bondi ng to other work is measured where the other work is existing 0 r consists 01 a diHering male rial
DEFINITION RULES
05 Battering walls are sloping walls with parallel sides 06 Tapering walls are walls 01 diminishing thickness 07 Thickness stated lor tapering walls is mean thickness 08 Walls include skins 01 hollow walls 09 Columns are walls whose length on plan is s lour fimes their th iclmess, except where caused by openings 010 Attached columns include attached piers and pilasters
COVERAGE RULES
C2 Battering and tapering walls are deemed to include the extra materials required C3 Work is deemed to include exira materi al tor bonding
SUPPLEMENTARY INFORMATION
511 Method 01 bonding to backing
S12 Type and spaci ng 01 1ixing and method 01 securi n9 to backi ng
Dl1 The dimensioned description stated 101 attached colum ns rele rs 10 the projection only
m'
'I----
1 Mached 2 Attached with different fin ish. type 01 finish stated 3 Isolated
1 Dimensioned descrip~on
012 AUaehed slo nes are Ihose attached to the same type 01 stone wailing 013 Isolated stones are those attached to another lorm 01 construction
t Dimensioned descripti 0 n
13 Slab surrounds to
openings
014 Slabs are those which are not bonded to their surrounding work
1 Vertical
2 Raking
3 Horizontal 4 Others, detai Is stated
17 Handrails
18 Cappings 19 Kerbs
M7 Mo uldi ngs are only measured separately on superficial items of masonry and attached piers. Mouldi ngs are given in the description 01 Iinear items
015 Band courses and the like include mouldings, enrichments, cornices and the like 016 Plain bands> 300 mm wide are measured as walling or faceworll
nr
--
M8 Arches are measured the mean girth or length on face M9 The quantity (nr) is only stated in an item which is meas urad Iinearl y
25 Closing cavities
26 Rough raking or circular cutting 27 Fair raking or circular cuMing 28 Grooves 29 Throats
1 Size stated
30
Flutes
31 Rebates
MtQ Grooves, throats, flutes, and rebate s are on Iy measured separatety on superficial items 01 masonry and attached piers
32 Chases
1 Rough
2 Fair
F20/F21/F22 continued
CLASSIFICATION TABLE
33 Special purpose stones 1 Function stated 1 Plain cuboid. dimensions stated 2 Dimensioned description nr
MEASUREMENT RULES
Mil Descriptions of stones are given as the smattest block from which each item can be obtained having regard in the case of natural stone to the plane in which the stone is required to be laid with relation to its quarry bed. The dimensions are taken over one mortar bed and one mortar joint
1 Providi ng models
DEFINITION RULES
COVERAGE RULES
34 Carvings 35 Sculptures
1 Component drawing
nr
C4 Carvings and sculptures are deemed to include: (a) selecting blocks of stan e for size and quality (b) boasting for calVing (c) working mouldings or similar members M 12 A dimensioned description of centering gives the shape and width of the surface to be supported. the span of the soffit. and, in the case of arches. whether segmental, semicircular. invert and the like. stating the rise C5 Centering is deemed to Include: (a) strutting. shoring, bolting. wedging, easing. striking and removing {b) cutting (e) scribed and splayed edges (d) notchi ng for key blocks. projecting voussiors and the like S13 Nature of supported surface
36 Centering
1 Arches 2 Tracery
1 Dimensioned description
nr
1 Sloping soffits 2 Maximum support height 3.00 - 450 m 3 and thereafter in 1.50 m stages 4 left in
J Projecti ng mason ry
4 Vaulting
F30
INFORMATION PROVIDED PI
The following information is shown either on location drawings under A Preliminaries/General conditions or on further drawings which accompany the bills of quantities: (a) plans of each floor level and principal sections showing the position 01 and the materials used in the walls (b) external elevations showing the materials used
DEFINITION RULES
COVERAGE RULES
Cl Accessories are deemed to include: (a) rough and fair cutting on walls around accessories (b) bedding and poi nting accessories (c) extra materials lor curved work
SUPPLEMENTARY INFORMATION
SI Kind and quality 01 materials
CLASSIFICATION TABLE
1 Forming cavities 1 In hollow walls 2 Between walls and other work 1 Width of cavity stated m2 1 Rigid sheet cavity insulation, thickness stated
S2 Type, size and spacing 01 wall ties S3 Type, thickness and method of fixing cavity insulation M2 No allowance is made tor laps M3 No deduction is made for voids::; 05{J m2 C2 Damp proof courses are deemed to include pointing exposed edges S4 Gauge, thickness or substance of sheet materials S5 Number of layers S6 Composition and mix of bedding materials S7 Minimum laps
m2
1 Cavity trays
3 Joint reinforcement
1 Wfdth stated
M4 No allowance is made for laps C3 Fillets are deemed to include ends and angles M5 Flashings are measured in Sections H70-H76
I--m I-m M6 Joints are only measu red where desig ned C5 Work is deemed to include lXepara~on, cl eaners, primers and sealers S8 Type of filler and sealant S9 Method of application S10 Preparation of contact surfaces, cleaners, primers and sealers
1 Dimensioned description
1 Width stated
1 Courses (01)
C6 Slates and tiles tor creaSing and sills are deemed to include ends, angles and pointing
F30 continued
CLASSIFICATION TABLE
11 Flue linings 1 Dimensioned description m
MEASUREMENT RULES
M7 Brick IIue linings are measu red in SeC1.ion
DEFINITION RULES
COVERAGE RULES
C7 Ftue linings are deemed to include: (a) cuning to form easings (b) cutting to form bends (c) cutting to walls around linings C8 Air bricks, ventilating gratings, soot doors and the Iike are deemed to include any necessary forming of openings, liners, cavity closers and damp proof
SUPPLEMENTARY INFORMATION
S11 Method 01 buitding
Fl0:91.00
nr
courses
1 Size 01 block and number of flues in each stated 1 Dimensioned description 1 Manufacturer's reference
f--nr
S12
Method of building
16 Proprietary
items
nr
S13
Method of fixing
G Structural/Carcassing metal/timber
G10 G11 G12
Structural steel framing Structural aluminium framing Isolated structural metal members
MEASUREMENT RULES on further
drawings
INFORMATION PROVIDED
PI The following information is shown either on location drawngs under A Preliminaries/General conditions or which accompany the bills of quantities: (a) the position of the work in relalion to other parts 01 Ihe work and of the proposed buildings (b) the types and sizes of structural members and their positions in relation to each other (c 1 details of connections or of Ihe reactions, moments and axial loads at connection points
DEFINITION RULES
COVERAGE RULES
SUPPLEMENTARY INFORMATION
SI Types and grades 01 materials S2 Details 01 welding tests and X-rays S3 Details of performance tests
CLASSIFICATION TABLE
t Framing, Iabricanon
1 Columns 2 Beams 3 Bracings 4 Purlins and cladding rails 5 Grillages 6 Overhead crane rails 1 Details of fixing clips and resilient pads stated
1 Weig ht s; 40 kg/m
2 Weight 3 Weig ht
40-100 kg/m
M2 Fittings
02 Purlins and claddmg rails are measured by weight when hal rolled 03 Wires, cables. rods and bars include sag rods, ties and the like
04 Special bolts and fasteners are those other than black bolts and holding down bolts or assemblies
Cl Items lor fabrication measured by weight are deemed to indude shop and site black bolts, nuts and washers for structural framing to structural framing connecnons
1 Details of construction
stated
10 Fillings
tl Hotding down bolts or assembfies 1 Details slated nr
1 Triat erection
05 Erection includes all operations subsequent to fabrication 1 Curved 06 Permanent lormwork is that which is structurally integral with the framing
ml
1 Type and method of fixing slated 1 Plain member stated use 1 Weight 2 Weight 3 Weight ::::;40kg/m
1 Castellated 2 Tapered
3 Curved
4 Cambered 5 Hollow, shape Slated
M6 The mass of built up members is calculatad as defined from 'Framing, fabrication' M7 Fixing bolts are measured in accordance with the rules contained in Section G20 :25_ .0.0
07 An isolated structural member is 8 member not part of H framing as measured under 1.1 -12 08 Use is defined as 1.1 - 1.9 inclusive 09 FixinQ bolts are bolts fixin~ an isolated structural mem er to another element
:> Concrete
7 Surface preparation 1 Blast cleaning 2 Pickling 3 Wire brushing 4 Flame cleaning 5 Others, details staled
I
m2
Surlace trealmenl
m2
_____,
m2 M8 Localised protective coating is only meas urad to structural aluminium lraming 010 localised protective coatings are localised applications to surfaces in contact with dissimilar metals and aggressive building materials
1 Type stated
G20
INFORMATION PROVIDED
PI The following information is shown eilher on location drawin:gs under A Preliminaries/General which accompany the bills ot quantities: (a) Ih e scope and location 01 th e worll
DEFINITION RULES
01 All sizes are nominal sizes unless staled as finished sizes
COVERAGE RULES
Cl The work is deemed to include labours on ilems at limber, excepl as olherwise requried
SUPPLEMENTARY INFORMATION
SI Ki nd and quality of materials and if limber whether sawn or wrol S2 Method of fixing where not at the discretion of the Contractor S3 Fixing through vulnerable materials
CLASSIFICATION TABLE
1 Trusses
2 Trussed rafters 3 Trussed beams 4 Wall or partition panels 5 Portal trames 6 Floor members 7 Wall or partition members 8 Plates 1 Dimensioned description m 1 Lenglh > 6,00 m in one continuous length, length stated 1 Dimensioned description nr 1 Stopped labou rs (nr) C2 The work is deemed to include webs, gussets, etc,
54 Preservative Ireatments applied as part of the production process S5 Surface treatments applied as part of the production process
S6 Selection and protection for subsequent treatment S7 Matching grain or colour Umits on the planing margi ns and if deviation trom the stated sizes is not permitted
03 Partiijon members
include struts and noggings 04 Plates are mose to structural elements only and include bearers
sa
9 Roof members
1 Flal 2 Pitched
05 Flat roof members include joists and bea ms D6 Pitched root members include struts, purlins, rafters, hip and valley rafters, ridge boards, ceiling joists, binders and braei ng
59 Method of jointing or form of construction where not at the discretion of the Contractor
to Joist strutting
cross-secton
07 Supports include grounds, batts ns. firrings, fillets. drips, rolls, upstands, kerbs or Ihe like 08 Framed supports are where the members are Jointed together other than butt jointed
13 tndividual
supports
m2 m
-----------------
M3 Gutter boards and sides are each measured overall as rndivid ual components but grouped together
09 Gutter boards include sides 010 Fascia boards include barge boards
3 Width s 300 mm 1 Dimensioned description nr 011 Cleats include sprockets and the like
18 Ornamental ends
19 Wlot surfaces 1 Plain 2 Irregular 20 Straps 2t Hangers 1 Dimensioned description 2 Dimensioned diagram 1 Widlh stated 1 Girth stated m D12 Wrot surfaces are those on sawn items only
nr
-----------------
C3 Work is deemed 10 include all labours in fabricating and fixing C4 Work is deemed to include all accessories
22 Shoes 23 Nail plates 24 Metal connectors 25 Bolts 26 Rod bracing 27 Wi re bracing 28 Others. details stated
G30
PI The following informalion is shown either on drawings under A Preliminaries/General accompany Ihe bills of quantities: (a) the enem of Ihe work and its height above ground level (b) the size of units where not at the discretion of the Contractor
DI All siz es are nom inaI sizes unless slated as finished sizes
CI Removalolli"ing devices and consequent making good and making good of handling holes and the like are deemed to be included
CLASSIFICATION
TABLE
S 4 Sur1ace treatments applied as part of the production process I Dimensioned description m' 1 Curved, radii slated 2 Fixing through underlinings 1 Holes 2 Notches 3 Others, deta.ils stated I Off site 2 Onsite nr Ml The number is stated on'Y where the size of unit is not at the discretion 01 the Contractor M2 No cedocton is made for voids sO_50 m'
3 Items extra over the decking or decking units in which they occur 4 Bearings 5 Eaves 6 Kerbs 7 Abutments 8 Nibs 9 Blocks 10 Fillets 11 Profile fillers
1 Dimensjoned descrip~on
G31 G32
Edge suppo rted/Rei nforced woodwoo Ilroc kfi bre deck ing
MEASUREMENT RULES
conditions or on further drawings
INFORMATION PROVIDED
Pl The following informaMn is shown either on location drawings under A PreliminariesJGeneral which accompany the bijlls 01 quantities: (a) the extent of the work andi ts heig ht above ground level (b) the size Of units where not at the discretion of the Contractor
DEFINITION RULES
01 All sizes are nomin al sizes unless stated as lin ished sizes
COVERAGE RULES
Cl Removal of lifting devices and consequent making good, and making good 01 handling holes and the like are deemed to be inCluded
SUPPLEMENTARY INFORMATION
CLASSIFICATION TABLE
1 Decking 2 Declling units (nr) 1 Dimensioned description m' 1 Cu rved, radii stated
t OHsite
2 On site
nr
Ml The numbe r is slated on ty where the size of u nit is not at the di seretion 01 the Contractor
M2 No deduction is made tor voids s 0.50 m'
4 WoodwOOI kerbs 5 Woodwool angle filtets 6 Filii ng rebates with insulating strips 7 Isolating strips
1 Dimensioned description
M3 Items 4-7.+.0
on Iy measured under Sec~on G32
* am
53 Method of JOinUng or form of construction where nol at the discretion of the Contractor
S4 Selection and protection for subsequent treatment S5 Surface treatments applied as pari of the
producton precess
56 57
Limits on the pianing margins and ~ deviation trom the stated sizes is not permitted
H Cladding/Coveri ng
H10 H12 H13
Patent glazing Plastics glazed vaulting/walling Structural glass assemblies
MEASUREMENT RULES
condilions or on further drawings
INFORMATION PROVIDED
P1 The following information is shown enher on location drawings under A Preliminaries/General wtlleh accompany the bills of quan~ties: (a) the scope and location ollhe wo rk (b) component drawings
DEFINITION RULES
COVERAGE RULES
SUPPLEMENTARY INFORMATION
SI Kind, qual ity and thickness of materials S2 Type, finish, length and spacing 01 9 lazing members
CLASSIFICATION TABLE
1 Rools areas (01) 2 Vertical surfaces (nr) ,3 Items extra over the glazing in which th ey occur 1 Single tier 2 Multi-Jier 1 Doors 2 Windows 3 Fixed louvres 4 Adj ustabte louvres 50th ers, d eta iIs stated 1 Dimensioned description nr 1 Contro' gear to single unit, type, method of fixing and distance vertically and horizo ntally Irom un it stated 2 Control gea r to bank of units, type, matn ad of fixing and di stance ve rtically a nd horizon tatty from u nits stated m m1 1 Si led rilling the beari ng s M 2 Glaz ing is measu red over bars Cl Work is deemed to include securing to wood unless otne rwise slated
4 Raking cutti ng 5 Curved cutting 6 Weatherings, flashings and fixing members at tops, bottoms and sides where part 01 the component t Preformed, gauge staled 2 Extruded, thickness staled 1 Dimensioned description
H11
Curtain walling
MEASUREMENT RULES
conditions or on further drawings MI Timber members which do not have a constant cross-section are so described and given stating the extreme dimensions M2 No deduction is made for voids s 1,00 ml
INFORMATION PROVIDED
PI The following information is shown either on location drawings under A Preliminaries/General which accompany the bills of quantities: (a) the scope and location of the work (b) component drawings
DEFINITION RULES
01 Curtain walling compri ses non loadbeari ng walls of wood or metal framing, fixed as an intergr atsd assembly, complete with windows and opening lights, glazing and infill panels 02 All sizes are nominal sizes unfess staled as finished sizes
COVERAGE RULES
SUPPLEMENTARY INFORMATION
CLASSIFICATION TABLE
1 Curtain walling 2 Items extra over the curtain walling in which they occur 1 Infill panels 1 Dimensioned description 1 Type and thickness stated ml m' 1 Flat 2 Sloping 3 Curved. radii stated 1 Irregular 2 Horizonlal 3 Sloping 4 Vertical 5 Curved, radii stated M3 In~1Ipanels are measured over all framing
Ct Curtain walling is deemed to include all cleats, brackets, bolts and fixings C2 Items include: (a.) doors where supplied with the unit (b) architraves, trims and th e like where part 01 the component (c) ironmongery where supplied with the component (d) finishes where part 01 the component as delivered (e) glazing where supplied with the component (f) mechan ical operation and automatic operating equ ipmenl wh ere supplied with the component (g) mastics/sealants unless executed by a specialist and measured in Section P22 (h) fixings and fastenings
St Kind and quality of materials and if timber whether sawn or wrot S2 Preservative treatments applied as part of the production process S3 Suriace treatments applied as part 01 the production process
2 Perimetsr
03 Irregular junctions are any ju ndions with angles othe r than 900
3 Angle
1 Internal 2 External
4 Closer
1 Dimensioned description
nr
S9 Method affixing where not at the discretion of the Contractor SIO Bedding and jointing or poi nling compound S11 Fixing throug h vu Inerable materials
H14
iii
SUPPLEMENTARY INFORMATION
INFORMATION PROVIDED
-------------~-~-
(nr)
m'
nr m
--
Ci Roof and pavement lights are deemed to include moulds, lormwork, reinforcement, bedding.and glass lenses
sealants staled
Glassfi bre reinforced gypsum Ii nings/panell iog/casi ngs/mou Idings Vitreous enamel linings/panelling K20 Timber board floori ng/decking/sarking/I inings/casi ngs
INFORMATION PROVIDED PI Intormation is shown on location drawings under A Preliminaries/General COnditions MEASUREMENT RULES DEFINITION RULES COVERAGE RULES Cl The work is deemed to include: (a) labours, except as otherwise required (b) breather paper lining/sheathing (el angtes, except as otherwise required SUPPLEMENTARY INFORMATION
intemal unless described as external 02 All sizes are nominal sizes unless stated as finished sizes 03 TImber ~ems which do not have a constant crosssecton are so described and given stating the extreme dimensions
CLASSIFICATION TABLE
1 Walls 1 Width>
300 mm
Di me nsionec descripti 0 n
mt
2 Floors
3 ~ilings
4 Roots 5 Tcps and cheeks 01 dormers
2 Width s 300 mm
3 Area s
i.co m
Dr -
04 Walls include jambs and cills to openings and recesse s in walls and attached columns Ceilings include soffits 10 openings and recesses in walts, all faces 01 recesses in ceilings aM attached beams 05
51 Type, quality and thickness of materials a.M if limber whether sawn or wrOI S2 Method of joinling 01 form 01 construction where not at the discretion 01 the Contractor S3 Na1ure of background S4 Preservatve treatments appl ied as part 01 the production process
2,
irrespec1ive of width
Isolated beams
mt
7 Isolated columns
D6 S lopi ng is defined as
sloping both > 10° from horizonta.1 and> 10°from vertical 07 Isolated beams and isolated columns inClude the faces 01 attached beams and attached colum ns which have a diftere nt finiSh from the adjoining face
55 Surtace treatments
applied as part of the production process
56
. 8 Abutments
1 Type stated
08 Abutments are defined as being where the detail is difterent tmrn the standard detail and (where appropriate) include around openings etc.
9 Finished angl as
1 External
I-m
loternal
09 Finished angles are those where the decorative veneer or facing is returned or on panelling where angles are other than butt jointed 010 Holes are those for pipes, standards and the like
I-or f-m nr
12
Fibre cement profiled sheet cladding/covering/siding Metal profiled sheet cladding/covering/siding Plastics profiled sheet cladding/covering/siding Bitumen and fibre profiled sheet cladding/covering Glassfibre reinforced plastics panel claddinglfeatures Metal panel cladding/features
MEASUREMENT RULES
conditions or on further drawings
INFORMATION PROVIDED
PI The tollowing information is shown either on location drawings under A Preliminaries/General which accompany the bills of quantities:
(a) the extent 01 !he work and its height above ground level
DEFINITION RULES
COVERAGE RULES
SUPPLEMENTARY INFORMATION
SI Klnd, qUality and size 01 materials S2 Type and spacing 01 fixing
CLASSIFICATION TABLE
1 Roof coverings 2 Wall cladding 1 P~ch stated ml 1 Curved, radii stated 2 Fixed through underlinings Ml No deducbon is made for voids s 1,00 m2 Ct Coverings are deemed to include: (a) work in forming voids s 1 ,00 m2 other than holes (b) integral underlay
3 Abutments 4 Eaves 5 Verges 6 Ridges 7 Hips 8 Vert~1 angles 9 Valleys 1 0 Expa nsion ja; nts 11 Barge boards 12 Skirtings 13 Flashings 14 Aprons/sins 15 Gullers and linings 16 Jambs 17 Filler pieces
M2 Boundary work to voids is only measured where the void is > 1,00 m1
C2 Boundary work is deemed to include bedding, pointi ng, ends, angles and intersections
18 Items extra over rool coverings 19 Ilems extra over wall cladding
1 Translucenl sheets 2 Sheets wrth soaker flanges 3 Rooflight units 4 Sheets w~h louvre blades
1 Dimensioned descripli(ln
nr
5 Ventilators 6 Junc~ons
20 Cutting 1 Raking 2 Curved
-
21 Holes
nr
H51 H52
INFORMATION
PI The following inlormation is shown either on loca~on drawings under A Preliminaries/General which accompany the bills of Quantities: (a) the scope and location of the work
Ml Work is measured on
the exposed face and no deduction is made lor voids s 0.50 m' M2 Work in staircase areas and plant rooms are each given separately M3 Work to ceilings and beams over 3.50 m above floor (measured to ceiling level in both cases), except in staircase areas, is so described stating the height in further 1.50 m stages
01 All work is deemed external unless described as internal 02 The thickness stated is the thickness exclusive 01 keys, grooves and the like 03 Rounded internal and external angles> 10 mm radius are classified as curved work where not measured under 15.1.*.0
Cl The work is deemed 10 include: (a) fair joints (b) working over and around obsmcnons (e) additional labour tor overhand work (d) wtting (e) drainage holes (II bedding mortars and adhesives (g) grouting (h) cleaning, sealing and polishing
54 Preparatory work
S5 Nature of finished surface including any sealing/polishing 56 Bedding or other method of fixing 57 Treatment of joints
CLASSIFICATION
TABLE
M4 Curved work is SO described wijh the radii stated measured on face 1 Plain, width > 300 mm 2 Plain, width s 300 mm 3 Work with joints laid oul to detail, widltl > 300 mm 4 Work wrth joi nts laid out to detail, width S" 300 mm i Dimensioned description
58 Layout of joints
r-m m2
ml
D4 Beams and columns are classified as isolated where the work is different from the abuWng ceilings or walls
05 Work to sides and soffits of attached beams and openings and to sides 01 attached columns is classed as work to the abutting walls or ceilings
C2 Work to walls, ceilings, beams and columns is deemed 10 inctude internal and external angles and intersections!> 10 mm radius
r-m
5 Floors
I Level or to falls only s; 15° from horizontal 2 To falls and crossfalls and to slopes ~ 15° from horizontal 3 To slopes> 15° from horizontal
t Plain
2 Work with joints laid out to detail, dimensioned diagram staled
m1
I Paltemed work. details stated 2 Floors laid in bays, average size of bays stated 3 Inserts, size or section stated
06
6 Treads
I
I
t Width stated
C4 Wolll. to treads, si lis and risers is deemed 10 include tair edges, internal and external angles C5 Curved treads, risers, strings and aprons are deemed to include curved and radiu.sed cuning tor speci al edge tiles C6 Strings and aprons are deemed 10 inClude lair edges, ends, angles and ramps
Strings
10 Aprons
11 Unings to channels
1 Horizontal
2 To tailS
I
I
C 7 Un ing.s to channels are deemed to include arrises, coves, ends, angles, intersections and outlets C8 Skirtings and kerbs are deemed 10 include fair edges, rounded edges, ends, angles and (amps
12 Skirtings 13 Kerbs
1 H eight slated
~~~--------------
3 Flush
4 Raking 5 Vertical 14 Corner pieces 15 Items e.xtra over the work in which Illey occur 1 Special units 2 Access units t Dimensioned description nr D7 Special units include non-standard units to prodoca fair edges, internal and external angles, moulded edges, beaded edges, and oovedjunctions
2 Manufacturer's
-~---------------
relerence
nr
3 Cover strips
4 Oivfding strips
59
Method 1)1fi~ing
5 Ornaments, dimensioned
description and characte r stated
1 In situ 2 Precast
nr
1 Undercut
nr
Plain roof tiling Fibre cement slating Natural slating Reconstructed stone slating/tiling Timber shingling Single lap roof tiling Bituminous felt shingling
MEASUREMENT RULES
conditions or on further drawings
1m
INFORMATION PROVIDED
PI The following information is shown either on location drawings under A Preiiminaries/General which accompany Ihe bills of quanti ties: (a) the extent of the rooting worn and its heighl above ground level
DEFINITION RULES
COVERAGE RULES
SUPPLEMENTARY INFORMATION
SI Kind, quality and size of materials 52 Method of fixing
CLASSIFICATION TABLE
1 Roof coverings 2 Wall coverings 1 Pitch stated m1 1 Curved, radii stated Ml No deduclion is made Cl Cove rings are deemed to include: (a) underlay and battens (b) wolll in forming voids S3 Minimum laps 54 Spacing 01 battens and counter battens
s 1.00 m2 other
holes 3 Abutments 4 Eaves 5 Verges m 1 Raking 2 Cu rved, lad ii stated M2 Sou ndaly work 10 voids is only measured where the void is > 1.00 mt
than
C2 Bou nd ary work is deemed to include underctoaks, cutting, bedding. pointing. ends. angles and intersections
S5 Method of forming
6 Ridges 7 Hips 8 Vertical angles 9 Valleys 10 Fittings 1 Ventilators 2 Finials 3 Gas terminals 4 Hip irons 5 Soakers 6 Saddles 11 Holes 1 Dimensioned descronon or 1 Fixing on Iy
nr
INFORMATlON PROVIDED
PI The following information is shown either on location drawings under A Pretiminaries/General
conditions or on further drawings which accompany the bitts of quantities: (a) the extent of the roofing work and its height above grouM level (b) the location and spacing of all laps, drips, welts, cross welts, beads, seams, rolls, upstands and downstands
weight and
S3 Method of fixing 54 Details of laps, drips, wells, beads, rolls, joints, upstands and downstands 55 Type of SUPllOrt
CLASSIFICATION TABLE
1 Roof coven ngs 1 Pitch stated m1 1 Curved, radii stated
Cl Coverings are deemed to include: (a) isolated areas (b) work to falls and crossfalis (c) underlay In contact with the covering (d) work in forming voids S; 1.00 m' other than holes (e) dressing/wedging into grooves, hollows, recesses and the like
ED
MEASUREMENT RULES
M3 Boundary work to voids is only measured where the void is > 1.00 ml
DEFINITION RULES
COVERAGE RULES
C2 Work is deemed to include: (a) laps, seams, ends (b) angles and intersecnons (c) rolls (d) upslands and downslands (e) dressi nglwedgi ng inl0 grooves, hollows, recesses and the like
SUPPLEMENTARY INFORMATION
--------------~--
15 Hips
16 Kerbs 17 Ridges 18 Reveals, returns and jambs 19 Valleys 20 Gutters
24 Edges 1 Welted 2 Beaded 3 Shaped 25 Dressings 1 Corrugated roofing 2 Slati ng and ti Iiog 3 Glass and glazing bars 26 Saddles 27 Soakers and slates 28 Hatch covers 29 Ventilators 30 Collars around pipes, standards and the like 31 Holes 1 Size 01 member and length of collar Slated nr Dl Collars include pipe sleeves D2 Holes are those lor pipes, standards and the like 1 Dimensioned descriplion nr 1 Handed 10others IOf iixing C3 All dressing and bossing is deemed included 1 Nature 01 roofing m 1 Down co rrugations 2 Across corrugations m
1 Details stated
J
J20 J21 J22 J30 J31 M11
Waterproofing
Mastic asphalt tanking/damp proofing
INFORMATION PROViDED
P1 The following information is shown either 011 location drawings under A Preliminaries/General conditions or on further drawings which accompany the bilts 01 quantities: (a) plan of each level indicating the extent of the work and its height above ground level together with restrictions on the siting 01 plant and materials (b) section indicating the extent of tanking work
DEFINITION RULES
01 Mastic asphalt flooring is deemed internal unless described as external
COVERAGE RULES
Cl Work is deemed to include: (a) cutting to fine (b) cutting. notching. bending and extra material for lapping the unde~ay and reinforcement (c) working into recessed duct covers and the like. shaped insets. recessed manhole covers, mat sinkings, outlet pipes, dishing 10 gullies and the like (d) work to falls and crossfalls C2 Work is deemed 10 include: (a) working to meta.1or other flashings and working against !rames of manhole covers, ducl covers and the like (b) intersections on work 10 crossfalls C3 Work subsequenlly covered is deemed 10 inelude edges and arnses
SUPPLEMENTARY INFORMATION
SI Kind, quality and size of materials including underla.ys and reinforcement 52 Thickness and number of coats S3 Nature 01 base on which applied S4 Surface treatments SS Method of fixing decking 56 Spacing of structural supports
CLASSIFICATION TABLE
1 Tanking a~d damp proofing 2 Flooring and underl.ay 3 Roofing 4 Paving I Widlh $150 mm 2 Width 150 - 225 mm 3 Width 225 - 300 mm 4 Width> 300 mm I Pitch Slated m1 1 Work subsequently covered 2 Carried out in working space s 600 mm wide 3 Overhand work M3 The area measu red is Ihat in contact with the base and no deduction is made 101 voids s 1.00 m'
1 Girth"
150mm
1 Stepped 2 Raking
2 Girth 150 - 225 mm 3 Girth 225 - 300 mm 4 Girth> 300 mm girth slaled
M4 Girth is measured on face M5 Boundary work to voids is onty measu red where me void is> 1.00 m'
C4 Skirtlngs, fascias and aprons are deemed to include edses, drips, arrises, inlernal angle-fillets, dressi ng over tilting fillets, turning nibs into grooves, angles, Slopped ends requ iring angle IiIlets, Slopped ends, fair ends, and extra. materials for turning into grooves C5 Linings to glllters, channels and valleys and coven ngs 10 kerbs are deemed to include edges, arrises, ,internal angle-fillets, tilting fillets, lu rn ing nibs into grooves, ends, angles, inlersec1ions, outlets and extra malerial for turning into grooves
1 Dimensioned descnplion
M6 12-17.*.0.* are only measured in association with work measured under 1-4.*.1.+
M7 Edges and arrises are only measured separatelv where the work is not subsequently covered
13 Fair edges
14 Rounded ooges 15 Drips 16 Arrise.s 17 Turning asphalt nibs into grooves 18 Collars around pipes, standards and like members 1 Size of member and length 01 collar stated
f-nr
C7 Collars around pipes, standards and the like are deemed 10 i nelude amses and internal angle Ii llets C8 linings to cesspools, sumps and the Iike are deemed to ineludearrises, internal angle-lillels and outlets
f--
1 Dimensioned description
nr
22 Edge trim
f-m
23 Rool ventilators
f-nr
Flexible sheet tanking/damp proofing Built up felt roof coverings Single layer polymeric roof coverings Proprietary roof decking with felt finish Sheet linings for pools/lakes/waterways
nON PROVIDED MEASUREMENT RULES DEFINITION RULES COVERAGE RULES SUPPLEMENTARY INFORMATION 51 Kind, quality and size of materials including undenays 52 Nature 01 base on which applied 53 Method 01 joi nling S4 Method 01 fixing deding S5 Spacing of structu fa I supports t Pitch stated ml 1 Curved radii stated M2 The area measured is that in contact with the base and no deduction is made for voids S; 1,00 m1 M3 Boundary work to voids is on Iy measured where the void is > 100 m2 C2 Bou nd ary work is deemed to include all cuHing, ends, angles, interseclions, notching, bending, turning into grooves, wedging, dressing, trimming and jointing covering to flashings, working into channels and the liKe and filler pi eces
PI The following information is shown either on location drawings under A Preliminaries/General conditions or on further drawings which accompany the bills of quanlities: (a) plan al each level indicating the extent of the work and its height above ground level together with restrictions on Ihe siting of plant and materials
CLASSIFICATION
TABLE
I Tanking and damp proofing 2 Roof coverings 3 Sliest linings 10 pools, lakes
or walerwaY$
4 Abutments 5 Eaves
I
ml
1 RaKing 2 Stepped
6 Verges 7 Ridges 8 Hips 9 Venical angles 10 Valleys. 11 Skinings 12 FIashi nilS 13 Aprons 14 Gutters and linings I 5 Coveri ngs to ke rhs
18 Lin in gs to cess pool s 17 Lin ing s to s um ps 18 Collars around pipes, stands rd sa nd 1M B Iike 19 Outlets and dishing to gullies
1 Dimensioned description
nr
~
20 Edge trim m
I--
or
~
or
~
1 Dimensioned description m
K Linings/Sheathing/Dry partitioning
K10 Plasterboard dry linings/partitions/ceilings
INFORMATION PROVIDED PI
The following inloffilation is shown either on location drawings under A Preliminaries/General conditions or on further drawings which accompany the bills 01 quantities: (a) the scope and location 01 the work (0) the servoes located within the ceiling or parti~on where the work includes comptex integral services
MEASUREMENT RULES
Work in staircase areas and plant foams are each 9 ivan separately
DEFINITION RULES
Dl Work is deemed internal unless described as external
COVERAGE RULES
Cl Work is deemed to include: (a) lair joints (b) working over and around obstructions into recesses and shaped inserts (c) additional labour lor overh and work (d) plaster lor dabs, filling and finishing (e) joint and reinforcing tape (I) bitumen impregnated pads C2 PaHerned work is deemed 10 include all extra wo rk involved
Ml
M2 Work to cei Iings and beams over 3.50 m above lloor (measured 10 ceiling level in bolh cases), except in stai rcase areas, is so described stali nJ;j the heig ht in further 1.50 m stages.
M3 Insulation. vapour barriers, fire barriers, isolating membranes. moisture resistant treatment and the like, are only measured in this section where they are an integ ra I part of a lining, or partition or cei lin g. or are fixe d theret.o
52
53
01 joints
54 Complex inteJ;jral services
55 S6
Method of fixing
Thermal insulation and vapour barriers fix.ed with liniflJ;! 57 tnsulation to limit sound lransmissio n
58
Moisture resistant treatment a nd the like 59 5urf~ce applications forming part of dry lining finish 510 IsolaliflJ;! membranes
CLASSIFICATION TABLE
I Proprietary partitions t Heighl in 300 mm stages an<! thickness of par1ibon stated I Walls I Boarded one side 2 Boarded bolh sides I Height in 300 mm stages staled I Total gir1h s 600 mm 2 and therealter in 60{1mm stages I Width 5: 300 mm 2 Width 300 - 600 mm m2 m m
1 Patterned, details stated
M4 The work is measured over obstructions M5 No allowance is made in measurement for lapped joints M6 The linear measurement 01 pamtians is the mean length of the par1ition M7 The linear measurement of linings is the length on
2 Linings
02 The height of framed work is th e height 01 the Irame and where the heig hts of the boarding dille r then this is so slated giving details 03 Reveals and soffits of openings and recesses in linings> 600 mm are defined as to wails, beams or columns 04 Linings are those which do no! lorm part of a proprietary system and exclude bmoor Irami ng
Iace
M8 No deduction is made 101 voids in par1itions and lin ings measu red Iinearly other than lor those voids which extend lull height, lull girth 01 lull width M9 No deduction is made for voids 5: 0.50 m2 in linings measured superficially
C3 Par1ltions and lini ngs are deemed to include the following where par1 of the proprietary system. Where not a pall ollhe proprietary system they are measured in accordance with the appropriate Work Seeton rules: (il) head and sole plates (b) studs, stillen ing sections, fiflings and channels (c) metal resilient bars (d) joi nling battens (e) insulation and barriers (f) lillets, banens and the like
Mil
A recess is only measured where it is for part on Iy of the heig ht and nol where il is full heighl 3 Angles
to parutions
1 Plain 2 Irregular
1 Th ickness of partilio n
staled
6 Abutments
7 Angles to linings
05 Abutments include Irimming to openings which extend full height, lull girth or full width unless linished with Ihe same finish as the faces. Trimming 10 openings which are not lull height. full girth or lull width are deemed to be included
C4 Angles, tee junctions, crosses and abutments are deemed 10 include lhe extra work involved, studding, grounds, angle tapes and the like
C5 Angles are deemed 10 include the exira work involved . .angle tapes and the like
r.P-I
1:8;1
MEASUREMENT RULES
m M12 Fair ends are only measured where me exposed en<.! 1the part~ion 0 is finished wilh the same finish as the faces, or with a trim which is an integral part of the partition system
DEFINITION RULES
D6 Fair ends to partitions include trimming 10 openings
COVERAGE RULES
C6 Fair ends are deemed to include the extra work involved, studding, boarding, Ifims and the like
SUPPLEMENTARY INFORMATION
513 Details of finish or trim
stated
1 Oimensioned description
nr
07 The function of beads as angle beads, casing beads, trims and the like are stated
C7 Beads are deemed to indude working finishes thereto CB Fixings for heavy fittings are deemed to include additional supports and any cutting of boarding, trim or jointing 514 Type of additional supports
1 Access panels
or
MEASUREMENT RULES
DEFINITION RULES
01 Work is deemed internal unless described as external
COVERAGE RULES
SUPPLEMENTARY INFORMATION
CLASSIFICATION TABLE
1 Partitions 1 Height and thickness of partition stated 1 FaClory applied finish 2 Site applied finish m m 1 Cu rved, radii stated 2 Obstructed by integral services Ml The work is measured over the obstructions M2 The linear measurement of partitions is the mean length of the partition M3 Factory applied finishes and site applied finishes are only measured where not at the discretion of the Contractor 02 Trims are separate items fixed on site as cover pieces to edges or panel joints 03 Openings is a general term for breaks in the general construction of partitions and includes the components filling the openings Cl Partitions are deemed to include all integral components, holes, etc preformed at factory but excluding trim SI Kind and quality of malerials 52 Method of construction
2 Trims
1 Dimensioned description
1 Oi mensioned description
nr
occur
C2 Openings are deemed to inctude additional integral components C3 Openings are deemed to include ironmongery. glass. linings or the like but exclude trim
S6 Method of bedding, jointing or pointing S7 Details 01 ironmongery, glass, linings or the tike
Access panels
MEASUREMENT RULES
DEFINITION RULES
COVERAGE RULES
SUPPLEMENTARY INFORMATION
CLASSIFICATION TABLE
1 Cubicle par1ilions; set 1 Dimensioned diagram nr Cubicle sets include doors, ironmongery or the like but exclude trims D2 Trims refer to separate items fixed on site at junclion of cubicles and al junctions with adjoining consnucnons
2 Trim
1 Dimensioned description
Cl Cubicle sets are deemed to include framing. stiffening, connecting and fixing devices supportings legs and brackets
MEASUREMENT RULES
Ml Soffit linings on battens, etc. fixed direct to underside
of slab are measured elsewhere in ihs relevant Sections M2 Work in staircase areas an d plant rooms are each give n separately M3 Work to ceilings and beams over 3,50 m above floor (measured to ceiling level in both cases), except in staircase areas, is so described stating the height in lurther 1.50 m stages
DEFINITION RULES
01 All work is deemed internal unless described as external
COVERAGE RULES
CI Suspended ceilings etc, are deemed to include (a) worki ng over and around obstructions (b) support work and accessories '-or fittings (c) suspension and framed members C2 Patterned work is deemed to include all exira work involved C3 Work incorporating integral fittings is deemed to include addiUonal hangers, Iraming and the like
SUPPLEMENTARY INFORMATION
SI Kind and quality of materials S2 Size of panels and strips S3 Construenon of framing and suspension systems S4 Method of fixing S5 NaMe of backgrounds S6 Services in Ihe suspended ceiling void S7 Insulation materials
S8 Vapour barriers S9 Integral healing, vennlanon, lighting and fire prevention fittings
CLASSIFICATION TABLE
1 Ceilings 2 Beams 1 Depth 01 suspension s 150mm 2 Depth 01 suspension 150 -500 mm 3 and thereal1er in 500 mm stages 1 Thickness 01 lining and method 01 Ii xin g system 10 str ucture stated ml 1 Pat\ernec. details stated 2 Siopi ng Iinings, details stated M4 The area measured is that 0 n t he exposed lace and no deduction is made for voids s 0_50 m' M5 The depth of suspension is measured from the main structural sollil to the lining M6 Insulation and vapour barriers are measured in this Section where they are an integral part 01 the ceiling and are Iixed in the ceilin g M7 Isolated strips of ceilings are not measured separately between the boundary 01 the lining and the lirst line 01 integral fittings 02 Intagral Ii"ings oceu r where Ihe littings are designed and incorporated into 1he ceiling structure
03 Isolated strips of ceiling are those which are narrower than the specdied relevant lining unit dimension
1 Access panels
1 Dimensioned description
nr
5 Upstands
1 Thickness 01 lining
MEASUREMENT RULES
DEFINITION RULES
COVERAGE RULES
C5 Irregular window and dormer cheeks are deemed to include cutting and extra supports C6 Cavity fire barriers are deemed to include an scribing, angles, ends, and support work
SUPPLEMENTARY INFORMATION
8 Edge mms
1 Plain
2 Floating
9 Angle trims
M8 Trims at regular inte!Vals within the area of suspended ceiling are included within the item description of same
D4 Plain edge trims are those which are fixed to the structure D5 Floating edge trims are those which are fixed to the ceiling system
C7 Trims are deemed to include mrtred. regular and irreg ular angles
1-3.*.*.5
M9 Trims are measured to openings formed for fittings
or
06 Irreg ular ang Ie pieces are purpose made manufactured corner pieces Ml0 Collars are measured where they are integral with fire barriers 1 Support to light fittings or the like S13 Types
or
MIt Bridging is measured where widths of trunking in the ceiling space obstruct the standard grid
13 Fillings
1 Dimensioned description
m nr
K41
INFORMATION PROVIDED
PI The following information is shown either on location drawings under A Preliminaries/General which accompany the bills of quantities: (a) the scope and location of the work
DEFINITION RULES
COVERAGE RULES
Cl Raised access floors
are deemed to include (a) panels. supporting structures. adhesives, bearing pads and the like (b) cuffing and notching and extra supports
SUPPLEMENTARY INFORMATION
SI Kind and quality of materials S2 S3 Supporti ng system s Frames to panels
CLASSIFICATION TABLE
1 Floors 1 Thickness of panel stated 1 Height 01 cavity stated m' 1 Patterned. details stated Ml No deduction is made for voids $; 0.50 m' M2 The height stated for ramps is the height at each end
54 Method of Iixi ng
nr
3 Items extra over the floors in which they occur 4 Ski rtings and perimeter edge trims
1 Special panels
1 Oimensioned description
nr
1 Dimensioned description
M3 Skirtings and perimeter edge frims not executed as part 01 the access floor are measured in Section P20
C 2 Skirtings and perimeter edge trims are deemed to include ends and angles
L Windows/Doors/Stairs
L10 Windows/Rooflights/Screens/Louvres
INFORMATION PROVIDED
PI Information is shown on location drawings under A PreliminaniesiGeneral conditions
MEASUREMENT RULES
DEFINITION RULES
01 All sizes of timber are nominal sizes unless stated as finished sizes
COVERAGE RULES
SUPPLEMENTARY INFORMATION
CLASSIFICATION TABLE
1 Windows and window frames 2 Window shulters 3 Sun shields 4 Rooflights, skylights, rool windows and frames 5 Screens, borrowed lights and frames 6 Shopfronls 7 Louvres and Irames 1 Dimensioned diagram
nr
C2 Items include: (a) doors wh ere suppl ied with the unit (b) architraves, trims, sills, sublrames, and the like where part of the component (c) ironmongery where suppl ied with th e component (d) finishes where part of the component as delivered (e) glazing wh ere suppl ied with the component (t) mechanical operation and automatic operating equipment where supplied with the component (g) lixings and fastenings
m
L20 Doors/Shutters/Hatches
INFORMATION PROVIDED MEASUREMENT RULES DEFINITION RULES COVERAGE RULES SUPPLEMENTARY INFORMATION
P1
conditions
CLASSIFICATION
01 All sizes of timber are nomina I sizes unless stated as finished sizes
1 Doors 2 Rolling shutters and collapsible gates 3 Slidinglfoiding 4 Hatches 5 Strong room doors 6 Grilles partitions
1 Dimensioned
diagram
nr
1 Approximate
weight
stated
MI Standard sections are identified M2 Each leaf of a multileafed door is counted as one door M3 Approximate weight is only stated for metal doors and inc ludes thei r associ ated frames M4 Doors where supplied with their associated Irarnes or linings are measured as composite items under General nute 9_1
Cl Doors are deemed to include fitting and hanging C2 The work is dee med to include notching around obstructions C3 Items include: (a) doors where supplied with the unit (b) architraves, trims and the like where part of the component Ie) ironmongery where supplied with the component (d) linishes where part of the com ponen 1as delivered (e) glazing where suppl ied with the component (tl mechanical operation and autom atie operating equipment where supplied wi Ih Ihe component (9) fixings and fastenings
SI Kind and quality of materials and if timber whether sawn or wrot S2 Preservatives treatment applied as part of the prod uclion process S3 Surface treatments applied as part ollhe production process S4 Selection and protec1ion for subsequent treatment S5 Matching grain or colour
1 Repeats 01 ide ntical sets (nr) 2 DiHerent cross-secfion shapes (nr) 3 Stopped labours (nrl
M5 Enumerated composite door frame and lining sets need not state the nu mber of sets within the description
S6 Limits on planing margins on timber and if deviation Irom stated size is not permitted S7 Method of jointing or form of construction S8 Method 01 fixing where not at the discretion of the Contractor S9 Fix ing through vu Inerable materials S10 Beddi n9, lointing and poi nling eom pound
----------------6 Composite sets 8 Bedding frames 9 Pointing frames t 0 Bedding and poi nting frames 1 Dimensioned description nr m
•
MEASUREMENT RULES DEFINITION RULES
01 Work in this Section covers: (a) staircases, ladders and loft ladders (b) landings, catwalks and access walkways (c) ba.lustrades and handrails (d) hatch doors where part 01 a loft ladder component or
Ml Where accessories such as linings, Uim nosings, ironmongery etc. are not included in a catalogue relerence they are measured in Ihe appropriate Work Sections M2 Isolated handrails are measured in Section P20 Cl Composhe items are deemed to include: (a) linings, nosings, cover moulds, trims and the like where part 01 the oomponent (b) soffit lining, spandrel panels and the like where part of the component (c) ironmongery and operating gear to loft ladders where supplied with the component (d) fi nishes where pari 01 the componenl as delivered (e) fixings, fastenings, blockings, wedges, bolts, brackets, cleats and the like C2 Staircases are deemed to include newels SI Kind and quality 01 materials and if timber whether sawn or wrol S2 Preservative treatments
COVERAGE RULES
SUPPLEMENTARY INFORMATION
CLASSIFICATION TABLE
1 Composite i1em, type stated t Dimensioned description
2 Component drawing
-----------------
2 Isolated balustrades
3 Associated handrai Is
4 Extra over the isolated balustrades or associated handrails in which they occ,,!r 1 Ramps 2 Wreaths 3 Bends 4 Ornamental ends or
02 Isolated balustrades are those which do not form an integral part at a staircase unit
03 Associated handrails are handraits 01 a material different from the balustrade with which th ey are associated