Documente Academic
Documente Profesional
Documente Cultură
1
10DWAbkg3.book Seite 1 Mittwoch, 22. Februar 2006 12:53 12
Welcome to BMW
i
1
Introduction
Contents
i
2
Introduction
Programming
Customising the anti-theft
alarm................................... 12
Default settings ................... 13
Accessing the
Introduction programming mode ............ 14
Welcome to BMW ................. 1 Programming ...................... 15
General ................................. 3 Exiting programming mode ...16
General
i
3
Introduction
Any attempt to move the motor- You can customise the anti-
cycle, change its position, start theft alarm in certain ways to
it without your permission, or suit your needs and prefer-
disconnect the battery will trig- ences.
ger the alarm. The sensitivity of
the system is set in such a way
that slight vibrations of the L Note:
motorcycle will not trigger a In order to protect the motorcy-
false alarm. cle’s battery and ensure that
Once you have activated the the engine can be started, the
alarm, any attempted theft is alarm system deactivates itself
indicated acoustically by the automatically a certain number
siren and visually by all four turn of days after being activated, al-
indicators flashing at the same though it always remains active
time. for at least 7 days.
10DWAbkg3.book Seite 4 Mittwoch, 22. Februar 2006 12:53 12
Controls
1 2
1
4 3
Overview and operation
L Note:
The signals from your remote
control unit could be disrupted by
interference from other radio sys-
tems or devices transmitting on
the same frequency.
If you encounter this problem, try
pointing the remote control unit at
the motorcycle from a different di-
rection.
10DWAbkg3.book Seite 6 Mittwoch, 22. Februar 2006 12:53 12
Activation
1 2
2
6
Alarm function
Activation
2
7
Alarm function
Activation phases
2
8
Alarm function
Alarm
1 2
2
9
Alarm function
Alarm
An alarm lasts for 26 seconds.
The alarm is active again
12 seconds later. You can can-
Triggering the alarm cel an alarm at any time after it
The alarm can by triggered has been triggered by pressing
• by the motion sensor button 2 on your remote control
• by an attempt to switch on the unit. This function does not
ignition with an unauthorised change the status of the anti-
key theft alarm.
• by disconnection of the anti- An acoustic alarm sounds and
theft alarm from the motorcy- the turn indicators flash for the
cle's battery (the anti-theft duration of the alarm. You can
alarm's internal battery cuts in program the sound of the
to supply power) acoustic alarm (b 15).
10DWA02g3.fm Seite 10 Dienstag, 22. Mai 2007 9:43 09
1 2
2
10
Alarm function
L
hand when you switched off
the ignition, it is reactivated Note:
30 seconds later) The alarm function can only be
or deactivated if the emergency
• by switching on the ignition stop switch is in the operating
with an authorised key position.
10DWA02g3.fm Seite 11 Dienstag, 22. Mai 2007 9:43 09
2
11
3
12
Programming
Default settings
3
13
Programming
Setting Status
Acoustic confirmation after activation/deactiva- OFF
tion
Type of acoustic alarm Intermittent
Automatic activation of alarm function when OFF
ignition is switched off
10DWAbkg3.book Seite 14 Mittwoch, 22. Februar 2006 12:53 12
1 2
3
14
Programming
Programming
3
15
Programming
The number of times the anti-
theft alarm telltale light flashes
indicates the step to which you
have progressed in program-
ming.
An alarm tone sounds as confir-
mation when you press
button 1, whereas an acknowl-
edgement tone sounds when
you press button 2.
The anti-theft alarm telltale light
stops flashing and four ac-
knowledgement tones sound
when you complete the final
step.
3
16
Programming
Programming is saved
• by switching off the ignition
after the final step is com-
pleted
or
• automatically 30 seconds
Programming mode is after completion of the final
cancelled step
• by switching off the ignition
before the final step is com- Four acknowledgement tones
pleted sound to indicate that you have
or exited the programming func-
• automatically if more than tion.
30 seconds are allowed to
elapse between any two con- Your custom settings are not
secutive steps in the pro- saved if programming is
gramming routine. aborted.
10DWAbkg3.book Seite 17 Mittwoch, 22. Februar 2006 12:53 12
4
17
4
18
Remote control units
1 2
4
19
3
4
20
Remote control units
Registration terminates
• once four remote control units
have been registered
• if the ignition is switched off
• if, after ignition OFF, 30 sec-
onds elapse without a button
being pressed
• if, after a remote control unit The LED flashes and the
has been registered, 30 sec- acknowledgement tone sounds
onds elapse without a button three times when registration
being pressed ends.
10DWAbkg3.book Seite 21 Mittwoch, 22. Februar 2006 12:53 12
1 2
4
3 21
1 2
5
22
3
Upkeep and maintenance
e Attention:
Changing the batteries in Use only 3 V type CR 2032 lith-
the remote control units ium batteries.
The batteries in the remote con- Take care not to reverse polari-
trol units are due for replace- ty when inserting the battery.
ment after approx. 2–3 years. Inserting a battery of a different
You can tell when a battery is type or inserting the battery with
weak if LED 3 lights up only polarity reversed could cause
briefly, or not at all, when a but- irreparable damage to the de-
ton is pressed. vice.
10DWAbkg3.book Seite 23 Mittwoch, 22. Februar 2006 12:53 12
6
7 5
23
11
C R 2032
Technical data
6
24
Technical data
Anti-theft alarm
Neutral activation time 15 seconds
Alarm duration 26 seconds
Neutral time between two con- 12 seconds
secutive alarms
Operating temperature –40 °C to +85 °C
(–40 °F to +85 °F)
Trigger angle of the motion sen- ±0.7°
sor
Current consumption (idle cur- < 1 mA
rent with system active)
Operating voltage 9–16 V
Remote control unit
Range of the remote control unit approx. 10 m (33 ft)
Transmission frequency 433.92 MHz
(Japan: 315 MHz)
Signal frequency > 25 kHz (broadband)
Battery for remote control unit 3 V lithium battery,
type CR 2032
10DWAbkg3.book Seite 25 Mittwoch, 22. Februar 2006 12:53 12
A-Z
A T
Activation phases, 8 Technical data, 24
Activation with motion sensor, 6 Triggering the alarm, 9, 11
Alarm, 9
Alarm function
Deactivating, 10
i
25
C
Changing the battery, 22, 23
Index
Controls, 4
Customising
the anti-theft alarm, 12
D
Default settings, 13
F
Functions of the
remote control unit, 5
M
Motion sensor, 7
P
Programming, 14, 15, 16
R
Registration, 18
Remote control unit
Registering, 17, 19
Synchronising, 21
10DWAbkg3.book Seite 26 Mittwoch, 22. Februar 2006 12:53 12
i
26
Index
10DWAbkg3.book Seite 27 Mittwoch, 22. Februar 2006 12:53 12
i
27
Index
10DWAbkg3.book Seite 28 Mittwoch, 22. Februar 2006 12:53 12
i
28
Index