Documente Academic
Documente Profesional
Documente Cultură
LC1 LC2
Stress ON LC1
STRESS ON LC2
DISPLACEMENT ON LC1
DISPLACEMENT ON LC2
DISCUSSION OF RESULTS:-
LOAD CONDITION 1:-
As we consider the material STEEL for the following beam there are different properties of
steel which we considered. They are
Young's modulus…………………. 2e+011N_m2
Poisson's ratio……………………..0.266
Density……………………………7860kg_m3
Coefficient of thermal expansion……..1.17e-005_Kdeg
Yield strength…………………………2.5e+008N_m2
for the analysis of the load condition we have to dicusses about the boundary conditions,
displacements and stresses.
BOUNDARY CONDITIONS:-
For the boundary condition have to check the restrain conditions and the applied loads
Restrain conditions:-
For the restrain conditions i have used two different restrains pivot and slid as per
the given conditions it helps in locking and unlocking of the degree of freedom of
component in a free space.
APPLIED LOADS:-
Fx = 4 . 377e-008 N
Fy = 6 . 139e-012 N
Fz = -4 . 500e+003 N
Mx = 4 . 484e-006 Nxm
My = -2 . 373e-008 Nxm
Mz = -3 . 605e-009 Nxm
There is only one type of load is applied on the soild beam . with that it gives the
different Applied load resultants. They are
STRESSES:-
Stress is a intranal resistive force for the applied load. which is represented as
St= f/a
Where as
F= force
A=sectional area
When we apllied the loads on the beam these stresses are obtained for the above
boundary conditions
DISPLACEMENT:-
When we analyse the load condition 1, deformation of the mass has been takes palce from its orginal postion.
LOAD CONDITION 2:-
As we consider the material STEEL for the following beam there are different properties of steel
which we considered. They are
Young's modulus…………………. 2e+011N_m2
Poisson's ratio……………………..0.266
Density……………………………7860kg_m3
Coefficient of thermal expansion……..1.17e-005_Kdeg
Yield strength…………………………2.5e+008N_m2
for the analysis of the load condition we have to dicusses about the boundary conditions,
displacements and stresses.
BOUNDARY CONDITIONS:-
For the boundary condition have to check the restrain conditions and the load
conditions
Restrain conditions:-
For the restrain conditions i have used two different restrains pivot and slid as per
the given conditions it helps in locking and unlocking of the degree of freedom of
component in a free space.
Applied LOAD :-
There is only one type of load is applied on the soild beam . with that it gives the
different Applied load resultants. They are
Fx = 2 . 000e+003 N
Fy = -3 . 183e-012 N
Fz = -2 . 500e+003 N
Mx = -4 . 490e-007 Nxm
My = -1 . 920e+002 Nxm
Mz = -1 . 927e-006 Nxm
STRESSES:-
St= f/a
Where as
F= force
A=sectional area
When we applied the loads on the beam these stresses are obtained for the above
boundary conditions.
1. wall thickness
wall thickness:-
The thickness of the beam are considered from the british standards which
plays a key role in the
stiffness of the beam. By varying this regulate the strength and stiffness of the beam.
t= (d1 – d2) /2, where d1 , d2 are the ID and OD respectively
it is defined as the ratio between effevtive length and radius of beam and
which is important for
design considerations.