Documente Academic
Documente Profesional
Documente Cultură
Transmitting LED Visible Red 660nm Visible Red 660nm Infrared 880nm
Sensitivity Adjustment no no yes no yes no
Housing/Lens Material Specially formulated polymer/Acrylic
ical
Connection Type (-A2) 2m PVC, 300V cable, (-F4) 4Ćpin DC micro QD on six inch pigtail, (-G4) 4Ćpin AC micro QD on six inch pigtail
M hanic
Supplied Accessories One 18mm mounting nut, two on fiber optic models
Optional Accessories See accessories for mounting brackets, reflectors, apertures, fiber optic cables, cordsets, and patchcords
-25_ to +55_C (-13_ to +131_F) > 132V AC/DC
Operating Temperature
-25_ to +70_C (-13_ to +158_F) < 132V AC/DC
ntal
ment
Operating Environment NEMA 3R, 4X, 6P, IP67; 8270kPa (1200psi) washdown
En ironm
Vibration/Shock 5g, 10-55Hz, 1mm amplitude, meets or exceeds IEC 947-5-2 / 30G, 1ms pulse duration, meets or exceeds IEC 947-5-2
Envir
Complementary LO & DO PNP 42EF-P2MPB-a Ċ 42EF-D1MPAK-a 42EF-S1MPA-a 42EF-B1MPBC-a 42EF-B1MPBE-a 42EF-G1MPA-a 42EF-R9MPB-a 42EF-R9MPBV-a
DO NPN & PNP 42EF-P2KBB-a 42EF-U2KBB-a 42EF-D1KBAK-a 42EF-S1KBA-a 42EF-B1KBBC-a 42EF-B1KBBE-a 42EF-G1KBA-a 42EF-R9KBB-a 42EF-R9KBBV-a
LO NPN & PNP 42EF-P2JBB-a 42EF-U2JBB-a 42EF-D1JBAK-a 42EF-S1JBA-a 42EF-B1JBBC-a 42EF-B1JBBE-a 42EF-G1JBA-a 42EF-R9JBB-a 42EF-R9JBBV-a
Voltage/Current/Power Consumption 10.8 to 30VDC @ 35mA maximum (1W maximum)
Sensor Protection Input reverse polarity, over voltage, false pulse protected, output shortĆcircuit (SCP) to 100mA, overload
ors
ensors
MOSFET, Light operate output Ë 42EF-P2RFB-b 42EF-U2RFB-b 42EF-D1RFAK-b 42EF-S1RFA-b 42EF-B1RFBC-b 42EF-B1RFBE-b 42EF-G1RFA-b 42EF-R9RFB-b 42EF-R9RFBV-b
Sens
Voltage/Current/Power Consumption 21.6 to 264V AC/DC @ 25mA maximum (1VA maximum) 21.6 to 132V AC/DC for 42EF-xxxFx-a models
AC/DC S
Sensor Protection Input reverse polarity, over voltage, false pulse protected, output shortĆcircuit (SCP) to 100mA, overload
AC/D
1
Typical Response Curves
Polarized Retroreflective Standard Retroreflective Diffuse Sharp Cutoff Diffuse Transmitted Beam
6 100 100 100 1000
5
Operating Margin
Operating Margin
Operating Margin
Operating Margin
Operating Margin
4 20m
100
10 10 10
3
4m
2
1 1 1
1 1
0.01 0.1 1 10 0.1 1 10 0.1 1 10 100 2.54 25.4 254 0.1 1 10 100
(0.03) (0.328) (3.28) (32.8) (0.32) (3) (32.8) (0.04) (0.4) (3.9) (39) (0.1) (1.0) (10) (0.33) (3) (32) (328)
Distance to 76mm Reflector, 92-39Ċm (ft) DistanceĊm (ft) Distance to White TargetĊcm (in) Distance to White TargetĊmm (in) Distance to White TargetĊm (ft)
Polarized Retroreflective Beam Pattern Standard Retroreflective Diffuse Beam Pattern Transmitted BeamĊ4m Beam Pattern Transmitted BeamĊ20m Beam Pattern
0.2 0.5
20 150 15 0.4
Beam DiameterĊmm
Beam DiameterĊmm
Beam DiameterĊmm
0.1 0.25
Beam DiameterĊm
Beam DiameterĊm
100
10 0.12
50 5
0 0
0 0 0 -0.12
-50 -5 -0.1 -0.25
-10 -0.4
-100 -0.2 -0.5
-20 -150 -15 0 1m 2m 3m 4m 0 5m 10m 15m 20m
0 1 2 3 0 1 2 3 4 5 6 0 20 40 60 (3) (7) (10) (13) (17) (33) (50) (67)
(3) (7) (10) (3) (7) (10) (13) (16) (20) (8) (16) (24)
DistanceĊm (ft) DistanceĊm (ft) DistanceĊcm (in) DistanceĊm (ft) DistanceĊm (ft)
100 2
Groove in
100mm
0 100mm Sensitivity end tip
10 50mm Adjustment
50mm
-2
1
0 20 40 60 80 100 -4 Target
(0.7) (1.5) (2.3) (3.1) (3.9) 20 40 60 80 100
0 (0.7) (1.5) (2.3) (3.1) (3.9)
Distance to White TargetĊmm (in) DistanceĊmm (in)
Note: Due to the detection method, targets traveling horizontal to
Table 1ĊLED Function the sensor's optics are detected. Targets traveling vertically may
Label Color State Status not be accurately detected. For reliable background suppression,
a minimum separation distance of 6mm (0.24in) is recommended
OFF Output de energized between the target and the backgrounds.
Output
p Yellow ON Output energized
Flashing Output SCP active (DC models only) Sensor Alignment
OFF Margin < 2.5 The orange LED is an alignment aid which indicates that a margin of 2.5 has been reached. This means that the sensor is receiving at
Margin
g Orange
g ON Margin >2.5 least 2.5 times the signal strength back from the target needed to trigger an output signal. In general, it is desirable to have a higher
margin to help overcome any deteriorating environmental conditions, i.e. dust buildup on the sensor's lens. When aligning the sensor,
Flashing Output SCP active (AC models only) the best performance can be obtained if this margin indicator is illuminated with the target in place.
OFF Sensor not powered, output active, SCP active
Status Green When aligning diffuse mode sensors, ensure that the sensitivity be set at its maximum setting using the singleĆturn adjustment knob
ON Sensor powered on the front panel. Pan the sensor left, right, up, and down to center the beam on the target. It may then be necessary to decrease this
Note: For DC models output and margin LEDs alternate flashing when SCP active. setting to prevent the sensor from detecting a background object. If this problem persists, the application will require the use of a
background suppression, sharp cutoff diffuse, or retroreflective sensing mode.
Short-Circuit Protection
RightSight photoelectric sensors provide shortĆcircuit protection (SCP) on the output leads. This feature is intended to protect the
sensor from damage in the event that the output load is shorted to ground. If this condition does occur, the SCP will activate and the
orange LED will flash until the source of the short is removed (power must be reset for AC/DC models). The SCP limits are set to
100mA over the entire voltage range for both DC and AC/DC models.
2
Wiring Diagrams (continued)
10.8–30V DC Sensors 21.6–264V AC/DC Sensors
Models with Dual NPN and PNP Outputs AC Wiring for 42EF–_ _ _C_ _–_ _ Models
Brown 1 Brown
+ + Blue 2 Red/White
L1 L1
White 2 White
Load Load 1 4 3
Black Black 3 Red
4 Black Load Load
Load Load 4 2
2 3
Blue 3 Blue 1
– – Brown 1 Red/Black
L2 L2
DC Micro
Cable QuickĆDisconnect
Cable QuickĆDisconnect
Models with NPN Outputs AC Wiring for 42EF–_ _ _F_ _–_ _ Models
Brown 1 Brown
+ + Brown 1 Red/Black
White 2 White L1 L1
Load Load 1 4
Black Black 3 Red
Load 4 Black Load Load
Load
2 3
Blue 3 Blue
– – Blue Red/White
L2 2 L2
DC Micro
Cable QuickĆDisconnect
DC Wiring for 42EF–_ _ _C_ _–_ _ Models
Models with PNP Outputs
Brown 1 Red/Black
Brown
+ 1 Brown
+ + +
3
Black 4 Black 1 4 Black 3 Red
Load Load Load Load 4 2
White 2 White
Load Load 2 3 Blue 2 Red/White 1
Blue 3 Blue
– –
– –
Cable QuickĆDisconnect DC Micro Cable QuickĆDisconnect
Blue Red/White
– 2
–
Transmitted Beam Source
AC and DC Wiring
Brown 1 Red/Black
T L1/+
T
L1/+
Blue 2 Red/White
L2/- L2/-
Cable QuickĆDisconnect
Note: All wire colors on quick-disconnect models shown refer to Allen-Bradley cordsets.
3
Sensor Dimensions—mm (inches)
AC/DC 34.5 DC
(1.36) 34.5
20.5 27 (1.36)
(0.81) (1.06) 20.5 27
Sensitivity Adjustment (0.81)
10 (1.06)
(Diffuse and Glass
(0.40) 32.7 10
Fiber Optic Only)
(1.29) (0.40)
69 32.7
(2.72) (1.29)
46.7
9.6 49.7 (1.84)
(0.38) 27.5
4 (1.96) 10 9.6 (1.08)
26.5 (0.16) Indicators (0.38) 4
(1.04) (0.40)
M18 X 1.0 Thread (0.16)
19
19 (0.75) 3.6 (0.145) Diameter
(0.75) M18 X 1.0 Thread Clearance for #6-32
3.6 (0.145) Diameter 18mm mounting nut
16.5 Screw (2 Places)
Clearance for #6-32
16.5 2m (6.56ft) Screw (2 Places) (0.65)
(0.65) Cable
Accessories
Straight Bracket #60–2656 Right Angle Bracket #60–2657 Swivel/Tilt Bracket #60–2649 Apertures
10_Adjustment in (Transmitted Beam and
Each Direction
Retroreflective Sensing Modes
Only)
57.15
(2.25)
28.6
(1.125)
7.95
Note: 18mm nut must be installed
(0.31)
prior to installing aperture if threads
on optics snout are to be used.
50.08 1mm Qty. 20 #60-2660
(2.0) 2mm Qty. 20 #60-2661
4mm Qty. 20 #60-2662
AccessoriesĊDescription Catalog Number Aperture Set (4 each) #60-2659