Documente Academic
Documente Profesional
Documente Cultură
Number: 1Y0-A09
Passing Score: 680
Time Limit: 120 min
File Version: 2010-05-26
Exam: 1Y0-A09
Version: 2010-05-26
Questions: 81
QUESTION 1
Scenario: During the creation of a Microsoft Windows 2003 Standard Edition server virtual machine
(VM), an administrator is asked to make as many processors available as possible to allow a
developer to test a new multi-cpu application. What is the maximum number of VCPUs that an
administrator can assign to this VM?
A. 2
B. 4
C. 8
D. 16
Answer: B
Section: (none)
Explanation/Reference:
QUESTION 2
According to best practices, which step should an administrator perform before booting the
installer CD to upgrade to XenServer Enterprise Edition 5.0 from XenServer 4.x?
Answer: D
Section: (none)
Explanation/Reference:
QUESTION 3
Which two physical hardware configurations are supported by XenServer Enterprise Edition 5.0?
(Choose two.)
A. 512GB RAM
B. 256GB RAM
C. 32 CPU cores
D. 128 CPU cores
E. 32-bit architecture
F. 64-bit architecture
Answer: CF
Section: (none)
Explanation/Reference:
QUESTION 4
To allow for rapid deployment of XenServer hosts in a large environment, an administrator decides
to install XenServer Enterprise Edition 5.0 using a network boot process. To which type of server
must the administrator configure DHCP to communicate?
A. FTP
B. HTTP
C. TFTP
D. HTTPS
Answer: C
Section: (none)
Explanation/Reference:
QUESTION 5
Where can an administrator determine when a XenServer Enterprise Edition 5.0 license will expire?
A. XenCenter
B. XenServer Tools
C. mycitrix.com web site
D. Citrix License Management Console
Answer: A
Section: (none)
Explanation/Reference:
QUESTION 6
Scenario: An administrator is installing XenServer Enterprise Edition 5.0 in an environment. The
administrator has two disks available for storage. According to best practices, how should the
administrator configure the local disk storage repositories (SRs) during the initial XenServer
installation?
A. Install XenServer on one disk and the control domain on the other disk
B. Install XenServer on one disk and the virtual machine SR on the other disk
C. Install XenServer and an in-place upgrade partition on one disk and the control domain on the other disk
D. Install XenServer and the virtual machine SR on one disk and an in-place upgrade partition on the other
disk
Answer: B
Section: (none)
Explanation/Reference:
QUESTION 7
How much disk space is required for the control domain and guest VM storage repository in a
XenServer Enterprise Edition 5.0 installation?
A. 4 GB
B. 8 GB
C. 16 GB
D. 32 GB
Answer: C
Section: (none)
Explanation/Reference:
QUESTION 8
Scenario: An organization has a single installation of XenServer Enterprise Edition 4.0. The
administrator plans to upgrade the host to version 5.0. Which upgrade path should the
administrator take?
Answer: C
Section: (none)
Explanation/Reference:
QUESTION 9
Scenario: A company has acquired two small businesses recently. The administrator for the
company needs to create a template of a virtual machine (VM) that has Microsoft Exchange running
on Microsoft Windows Server 2003. The template will be used to create two more VMs to
accommodate the recent business expansion. In which way should the administrator create the
template?
Answer: D
Section: (none)
Explanation/Reference:
QUESTION 10
Which two steps must an administrator take to create a Microsoft Windows virtual machine using
the XenConvert Physical to Virtual (P2V) conversion tool? (Choose two.)
Answer: CD
Section: (none)
Explanation/Reference:
QUESTION 11
An administrator created a template of a Microsoft Windows XP SP3 virtual machine (VM) and now
needs to modify it. How can the administrator modify the template?
A. Power on the VM template, make the changes and save the template
B. Export the template from the XenServer host, import it to another system, power it on and make the
changes
C. Put the XenServer host in Maintenance Mode, make the changes to the VM template and then exit
Maintenance Mode
D. Create a new VM based on the original template, make the changes to the new VM and turn the new VM
into the new template
Answer: D
Section: (none)
Explanation/Reference:
QUESTION 12
What are two best practices for cleaning up a virtual machine after completing a Physical to Virtual
(P2V) migration using XenConvert? (Choose two.)
Answer: AD
Section: (none)
Explanation/Reference:
QUESTION 13
In which three locations could an administrator go within XenCenter to create a new virtual
machine? (Choose three.)
A. VM menu
B. Tools menu
C. New VM button
D. Templates menu
E. Add New Server button
Answer: ACD
Section: (none)
Explanation/Reference:
QUESTION 14
What are two differences between a Microsoft Windows virtual machine (VM) installation of the
XenServer Tools and a Linux VM installation of the XenServer Tools? (Choose two.)
Answer: BD
Section: (none)
Explanation/Reference:
QUESTION 15
Scenario: An administrator wants to create a new virtual machine (VM) on XenServer1, which does
NOT reside in the current resource pool. The administrator wants to keep the configurations exactly
the same as those in the resource pool but does NOT want to manually configure the new VM. How
can the administrator create the new VM with the same configurations as those in the resource
pool?
Answer: D
Section: (none)
Explanation/Reference:
QUESTION 16
An administrator must __________ on the virtual machines to return performance data to XenCenter.
(Choose the correct phrase to complete the sentence.)
A. Enable logging
B. Set the system alerts
C. Install XenServer Tools
D. Configure the management interfaces
Answer: C
Section: (none)
Explanation/Reference:
QUESTION 17
Scenario: An administrator is adding a new XenServer host to a pool and wants to ensure server
management connectivity. To do so, the administrator creates a new NIC bond using XenCenter.
However, after completing the task, the administrator is unable to join the server to a pool. Which
step must the administrator take before the XenServer can join the pool?
Answer: C
Section: (none)
Explanation/Reference:
QUESTION 18
Which three performance data points can an administrator locate for a virtual machine in the
Performance tab in XenCenter? (Choose three.)
A. CPU usage
B. Memory usage
C. Disk and network I/O
D. High availability status
E. VCPU resources allocated
Answer: ABC
Section: (none)
Explanation/Reference:
QUESTION 19
In which scenario should an administrator choose to suspend a virtual machine (VM)?
Answer: B
Section: (none)
Explanation/Reference:
QUESTION 20
Which two tasks can an administrator perform using the Storage tab in XenCenter? (Choose two.)
Answer: CD
Section: (none)
Explanation/Reference:
QUESTION 21
An administrator is in the process of disabling a XenServer host that is part of a resource pool and
migrating its virtual machines (VMs) to another XenServer host in a pool. What does the
administrator need to do to accomplish this?
Answer: D
Section: (none)
Explanation/Reference:
QUESTION 22
Which action must an administrator take to create an internal-only network in a XenServer
environment?
Answer: A
Section: (none)
Explanation/Reference:
QUESTION 23
Scenario: An administrator is configuring a Microsoft Windows virtual machine (VM) that has
XenServer Tools installed. While configuring the VM, the administrator is asked to set a bandwidth
limit of 100Mbps on the virtual NIC. How can the administrator set this limit?
Answer: B
Section: (none)
Explanation/Reference:
QUESTION 24
Which three tasks can be performed using the tabs in XenCenter? (Choose three.)
Answer: BCE
Section: (none)
Explanation/Reference:
QUESTION 25
Which three steps must an administrator take to dedicate a separate bonded interface to storage
traffic? (Choose three.)
Answer: ACD
Section: (none)
Explanation/Reference:
QUESTION 26
Which two steps does an administrator need to complete in order to disconnect a storage
repository (SR) without losing any data? (Choose two.)
Answer: AB
Section: (none)
Explanation/Reference:
QUESTION 27
An administrator needs to set up a storage repository that can be accessed over the network. Which
storage repository type should the administrator use?
A. NFS
B. NetApp
C. iSCSI SAN HBA
D. Fibre Channel SAN
Answer: A
Section: (none)
Explanation/Reference:
QUESTION 28
Which storage repository type allows an administrator to create a new storage repository that does
NOT erase any existing data on the specified storage target?
A. EXT
B. NFS
C. EQUAL
D. NetApp
Answer: B
Section: (none)
Explanation/Reference:
QUESTION 29
Scenario: An administrator was unable to add a XenServer host, XSA, to a resource pool. XSA
currently has all of its virtual machines shut down, does NOT have shared storage configured and
its system clock is synchronized with the pool master. The administrator also has checked the NIC
bond on the management interface and verified the hardware compatability of XS. What should the
administrator do to successfully add XSA to the resource pool?
Answer: B
Section: (none)
Explanation/Reference:
QUESTION 30
What must an administrator configure on the pool master to allow migration of virtual machines
(VMs) between servers in the pool?
A. NIC bond
B. High availability
C. Shared storage
D. Management interface
Answer: C
Section: (none)
Explanation/Reference:
QUESTION 31
Scenario: An administrator has established a Fibre Channel storage repository (SR) for a XenServer
resource pool. The administrator now wants to enable multipathing for the master server in the
resource pool and has verified that multiple targets are set up on the storage server. Which step
must the administrator complete before enabling multipathing on the SR?
Answer: B
Section: (none)
Explanation/Reference:
QUESTION 32
What must an administrator do to allow a resource pool to avoid emergency mode automatically
and promote a secondary server to master in the event the master server fails?
Answer: B
Section: (none)
Explanation/Reference:
QUESTION 33
An administrator attempts to add additional virtual NICs to an existing virtual machine (VM) but the
operation fails. Which reason best describes why the administrator may NOT be able to increase the
virtual NIC count?
Answer: B
Section: (none)
Explanation/Reference:
QUESTION 34
When using the command line interface to access a XenServer host remotely, an administrator
would like to authenticate automatically instead of entering the password. Which argument would
the administrator need to use to authenticate without entering the password?
A. -p
B. -u
C. -pw
D. -pwf
Answer: D
Section: (none)
Explanation/Reference:
QUESTION 35
In which two ways can an administrator backup the XenServer metadata? (Choose two.)
Answer: CD
Section: (none)
Explanation/Reference:
QUESTION 36
Which two XenServer CLI commands are valid? (Choose two.)
A. pool-backup
B. pool-ha-enable
C. pool-create-pool
D. pool-recover-slaves
Answer: BD
Section: (none)
Explanation/Reference:
QUESTION 37
What is the purpose of the XenServer CLI?
Answer: A
Section: (none)
Explanation/Reference:
QUESTION 38
An administrator is trying to shut down a high availability (HA) protected virtual machine (VM) in
order to perform maintenance, but the VM constantly restarts. What should the administrator do to
allow the VM to fully shut down?
Answer: B
Section: (none)
Explanation/Reference:
QUESTION 39
Scenario: An administrator needs to enable high availability (HA) within the existing resource pool.
While running the HA configuration wizard, the administrator finds that the environment does not
meet the storage requirements. What are the only two storage types supported in an HA-enabled
resource pool? (Choose two.)
A. NFS
B. Local
C. CIFS
D. iSCSI
E. Fibre Channel
Answer: DE
Section: (none)
Explanation/Reference:
QUESTION 40
Scenario: An administrator has been tasked with creating a disaster recovery solution for the
XenServer environment. The disaster recovery site must be identical to the main location; both
consists of a XenServer resource pool and shared storage. SAN replication has been enabled to
replicate data from the SAN at the main location to the SAN at the disaster recovery site. What other
task should the administrator perform to ensure that virtual machines (VMs) are easily recoverable
at the disaster recovery site?
Answer: D
Section: (none)
Explanation/Reference:
QUESTION 41
An administrator needs to change the high availability (HA) level for a virtual machine (VM) from
Restart if possible to Protected by using __________ and __________. (Choose the two correct
options to complete the sentence.)
Answer: AC
Section: (none)
Explanation/Reference:
QUESTION 42
Scenario: During the design phase for a new XenServer environment an administrator discovers
that in order to accomodate the level of network traffic expected, the XenServer host will need
2Gbps for storage traffic. All NICs will be connected to a 1Gbps switch in the main data center. What
is the minimum number of NICs the administrator will need to configure?
Answer: C
Section: (none)
Explanation/Reference:
QUESTION 43
Which two properties of a network interface on a virtual machine can an administrator set using
XenCenter? (Choose two.)
A. IP address
B. MAC address
C. Bandwidth limits
D. Virtual interface-uuid
Answer: BC
Section: (none)
Explanation/Reference:
QUESTION 44
Scenario: An administrator created a number of virtual machines (VMs) on which to test some new
applications. However, the administrator is concerned that the VMs may negatively impact the
network performance. Which type of network should the administrator create for the test machines
to ensure they do not negatively impact the network?
A. Internal
B. Bonded
C. External
D. ALB Bonded
Answer: A
Section: (none)
Explanation/Reference:
QUESTION 45
Which command can an administrator use to reset the maximum transmission unit (MTU) of a
virtual network interface (VIF) to use jumbo frames?
A. xe vif-param-set mtu=9000
B. xe vif-other-config=<vif_mtu=9000>
C. xe vif-other-config=<set mtu=9000>
D. xe vif-param-set uuid=<vif_uuid> \other-config:mtu=9000
Answer: D
Section: (none)
Explanation/Reference:
QUESTION 46
Which is a valid MAC address?
A. 127.0.0.1
B. 255.255.255.0
C. 6A:70:A0:5E:D0
D. 6A:70:A0:5E:D0:04
Answer: D
Section: (none)
Explanation/Reference:
QUESTION 47
What must an administrator do to dedicate a NIC to storage traffic in a XenServer environment?
Answer: B
Section: (none)
Explanation/Reference:
QUESTION 48
Scenario: An administrator is tasked with migrating a physical Microsoft Windows 2003 Domain
Controller to a virtual machine running on XenServer. The administrator attempts to use XenConvert
1.0 for the migration process, but fails to complete the migration successfully. Which option could
have caused the Microsoft Windows 2003 server migration failure?
Answer: B
Section: (none)
Explanation/Reference:
QUESTION 49
Which step must an administrator take after upgrading XenCenter and the XenServer host software
on systems in a pool from XenServer 4.x to 5.0?
Answer: C
Section: (none)
Explanation/Reference:
QUESTION 50
After completing an upgrade from version 4.1 to 5.0 for two XenServer hosts in a resource pool, an
administrator notices that a suspended virtual machine (VM) is unable to start. What must the
administrator do to restart the VM?
Answer: D
Section: (none)
Explanation/Reference:
QUESTION 51
How should an administrator apply licensing if there are four XenServer Enterprise Edition 5.0 hosts
in a resource pool?
Answer: A
Section: (none)
Explanation/Reference:
QUESTION 52
Scenario: An administrator recently created an ISO library for a XenServer environment. The
administrator now wants to make the ISO library available to all XenServer hosts. What must the
administrator do before the ISO library can be attached using XenCenter?
Answer: C
Section: (none)
Explanation/Reference:
QUESTION 53
To enable grouping of XenServer hosts into resource pools, live relocation of virtual machines
(VMs), and sharing of server resources, an administrator must __________. (Choose the correct
option to complete the sentence.)
A. Install XenCenter
B. Add shared storage
C. Run the xe pool-restore-database command
D. Assign a static IP address only to one XenServer host
Answer: B
Section: (none)
Explanation/Reference:
QUESTION 54
Scenario: An administrator created a template with a Microsoft Windows Server 2003 operating
system. After creating the template the administrator realized that Microsoft SQL was NOT installed
on the virtual machine (VM) that was supposed to be the SQL server for the company. What must
the administrator do to get Microsoft SQL on to the VM template?
Answer: C
Section: (none)
Explanation/Reference:
QUESTION 55
An administrator wants to take several virtual machines (VMs) out of service but does not want to
uninstall them in case they are needed again. Which action should the administrator take to ensure
that the VMs are out of service but still available for future use?
Answer: C
Section: (none)
Explanation/Reference:
QUESTION 56
An administrator can change the CPU priority settings of a virtual machine (VM) from the
__________ tab of a VM in XenCenter. (Choose the correct option to complete the sentence.)
A. General
B. Network
C. Optimization
D. Memory and VCPUs
Answer: D
Section: (none)
Explanation/Reference:
QUESTION 57
An administrator enabled Remote Desktop on a Microsoft Windows virtual machine (VM) and now
wants to use RDP in XenCenter. From which tab in XenCenter can the administrator enable an RDP
connection?
A. General tab
B. Console tab
C. Control Panel
D. System Properties
Answer: B
Section: (none)
Explanation/Reference:
QUESTION 58
What can be configured from the Performance tab of a virtual machine (VM) in XenCenter?
Answer: D
Section: (none)
Explanation/Reference:
QUESTION 59
How can an administrator enable a virtual machine (VM) to connect to resources available through a
physical NIC on a XenServer host?
A. Use VLAN 0
B. Add a new internal network
C. Add a new external network
D. Use the XenServer management NIC
Answer: C
Section: (none)
Explanation/Reference:
QUESTION 60
Which step requires an administrator to enable Maintenance Mode on a XenServer host?
Answer: C
Section: (none)
Explanation/Reference:
QUESTION 61
Which is the best way for an administrator to ensure that NIC failover is enabled for all virtual
machines (VMs) in a resource pool?
Answer: D
Section: (none)
Explanation/Reference:
QUESTION 62
Which four steps must an administrator complete to configure a shared logical volume manager
(LVM) over Fibre Channel and iSCSI storage repository? (Choose four.)
Answer: BCEF
Section: (none)
Explanation/Reference:
QUESTION 63
Scenario: The master server in a XenServer resource pool has failed and the secondary members
have gone into Emergency Mode. After approximately 20 minutes, the administrator confirms that
the master server cannot be recovered. The resource pool does NOT have high availability (HA)
enabled and the administrator now needs to make configuration changes. What must the
administrator do in order to make the necessary configuration changes in the resource pool?
A. Enable HA
B. Promote a secondary member to master
C. Use a Portable Storage Repository to recreate the master server
D. Shut down the master server and remove the secondary members from Emergency Mode
Answer: B
Section: (none)
Explanation/Reference:
QUESTION 64
An administrator created a resource pool and assigned a master server to the pool. How many
additional servers can the administrator add to the resource pool?
A. 7
B. 8
C. 15
D. 16
Answer: C
Section: (none)
Explanation/Reference:
QUESTION 65
As a best practice, before attempting to add a server to a pool, an administrator should __________.
(Choose the correct phrase to complete the sentence.)
Answer: C
Section: (none)
Explanation/Reference:
QUESTION 66
An administrator needs to access the XenServer host using a remote binary command line interface.
Which two sets of information must the administrator type before each command when accessing
the XenServer host remotely using the command line interface? (Choose two.)
A. Username / password
B. Hostname / IP address
C. Hostname / MAC address
D. Password file / IP address
Answer: AB
Section: (none)
Explanation/Reference:
QUESTION 67
An administrator created a Server Status Report of a resource pool containing two servers and is
now getting ready to view the resulting packaged zip file. Which two things will be included in this
zip file? (Choose two.)
Answer: AD
Section: (none)
Explanation/Reference:
QUESTION 68
In which two ways can an administrator restore the XenServer metadata from a backup? (Choose
two.)
Answer: CD
Section: (none)
Explanation/Reference:
QUESTION 69
Scenario: A XenServer host in an existing resource pool with high availability enabled has failed. All
virtual machines (VMs) are set to protected mode, but one of the VMs failed to start on the other
hosts in the resource pool. What could have caused the VM to fail to start?
A. The VM was NOT shut down properly
B. The resource pool is overcommitted
C. The VM was in a crash-consistent state
D. The VM timed out waiting for another VM to shut down
Answer: B
Section: (none)
Explanation/Reference:
QUESTION 70
An administrator is attempting to configure high availability (HA) using the appropriate storage
repository (SR) defined in the prerequisites but is unable to configure the heartbeat SR. What could
be the reason why the heartbeat SR cannot be set?
Answer: B
Section: (none)
Explanation/Reference:
QUESTION 71
Scenario: An administrator is using a regular snapshot method on a Microsoft Exchange server
running on Microsoft Windows Server 2008. The administrator finds an issue within the virtual
machine (VM) and decides to recover the Exchange server using the snapshot from the previous
day. Since applying the snapshot, users are reporting that they are unable to connect to their
mailboxes. What could be preventing the users from connecting to their mailboxes?
Answer: B
Section: (none)
Explanation/Reference:
QUESTION 72
Click the Task button to place the steps in the correct order for an administrator to configure
multipathing using XenCenter. Click the Exhibit button for instructions on how to complete a Drag
and Drop item. What is the correct order of steps for the configuration of multipathing using
XenCenter?.
Answer:
Section: (none)
Explanation/Reference:
QUESTION 73
An administrator wants to create a server status report. Click the Task button to complete the task.
Click the Exhibit button for instructions on how to complete a Hot Spot item. How does the
administrator create a server status report using XenCenter?
Answer:
Section: (none)
Explanation/Reference:
QUESTION 74
Click the Task button to place the steps to move a virtual machine running on a VMware ESX host to
a new XenServer host in the correct order. Click the Exhibit button for instructions on how to
complete a Drag and Drop item.
Answer:
Section: (none)
Explanation/Reference:
QUESTION 75
An administrator needs to connect a network to an external VLAN using the command line interface
(CLI). Click the Task button to place the steps necessary to connect a network to an external VLAN
using the CLI in the correct order. Click the Exhibit button for instructions on how to complete a
Drag and Drop item.
Answer:
Section: (none)
Explanation/Reference:
QUESTION 76
An administrator using XenCenter needs to apply an update to a group of XenServer hosts and
wants to ensure that pre-checks on the servers are conducted. Click the Task button to place the
steps in the correct order for an administrator to apply an update to a group of XenServers using
XenCenter. Click the Exhibit button for instructions on how to complete a Drag and Drop item. How
must the administrator apply the update to the group of XenServer hosts to ensure that pre-checks
on the servers are conducted using XenCenter?
Answer:
Section: (none)
Explanation/Reference:
QUESTION 77
An administrator needs to configure high availability (HA) for an existing resource pool. Click the
Task button to place the steps to configure HA in the correct order. Click the Exhibit button for
instructions on how to complete a Drag and Drop item.
Answer:
Section: (none)
Explanation/Reference:
QUESTION 78
Scenario: An administrator is installing XenServer Enterprise Edition 5.0 in an environment. The
administrator has two disks available for storage. According to best practices, how should the
administrator configure the local disk storage repositories (SRs) during the initial XenServer
installation?
A. Install XenServer on one disk and the control domain on the other disk
B. Install XenServer on one disk and the virtual machine SR on the other disk
C. Install XenServer and an in-place upgrade partition on one disk and the control domain on the other disk
D. Install XenServer and the virtual machine SR on one disk and an in-place upgrade partition on the other
disk
Answer: B
Section: (none)
Explanation/Reference:
QUESTION 79
An administrator created a template of a Microsoft Windows XP SP3 virtual machine (VM) and now
needs to modify it. How can the administrator modify the template?
A. Power on the VM template, make the changes and save the template
B. Export the template from the XenServer host, import it to another system, power it on and make the
changes
C. Put the XenServer host in Maintenance Mode, make the changes to the VM template and then exit
Maintenance Mode
D. Create a new VM based on the original template, make the changes to the new VM and turn the new VM
into the new template
Answer: D
Section: (none)
Explanation/Reference:
QUESTION 80
What must an administrator do to allow a resource pool to avoid emergency mode automatically
and promote a secondary server to master in the event the master server fails?
Answer: B
Section: (none)
Explanation/Reference:
QUESTION 81
Which two XenServer CLI commands are valid? (Choose two.)
A. pool-backup
B. pool-ha-enable
C. pool-create-pool
D. pool-recover-slaves
Answer: BD
Section: (none)
Explanation/Reference: