Documente Academic
Documente Profesional
Documente Cultură
Integrated DTMF Receiver
Bias
PWDN Circuit VRef
Buffer
Q1
Chip Chip
Power Bias High Group Digital Code
Filter Detection Converter
Algorithm and Latch Q2
IN + Dial
Tone Zero Crossing
Filter Detectors Q3
IN -
GS Low Group
Filter Q4
to all St Steering
Chip
Clocks GT Logic
4-11
MT8870D/MT8870D-1 ISO2-CMOS
4-12
ISO2-CMOS MT8870D/MT8870D-1
Functional Description
VDD
Following the filter section is a decoder employing Before registration of a decoded tone pair, the
digital counting techniques to determine the receiver checks for a valid signal duration (referred to
frequencies of the incoming tones and to verify that as character recognition condition). This check is
they correspond to standard DTMF frequencies. A performed by an external RC time constant driven by
complex averaging algorithm protects against tone ESt. A logic high on ESt causes vc (see Figure 4) to
simulation by extraneous signals such as voice while rise as the capacitor discharges. Provided signal
0 PRECISE
DIAL TONES
10 X=350 Hz
Y=440 Hz
DTMF TONES
20
ATTENUATION A=697 Hz
(dB) B=770 Hz
C=852 Hz
30 D=941 Hz
E=1209 Hz
F=1336 Hz
G=1477 Hz
40 H=1633 Hz
50
1kHz
X Y A B C D E F G H
FREQUENCY (Hz)
Figure 3 - Filter Response
4-13
MT8870D/MT8870D-1 ISO2-CMOS
R2
R1
ESt
b) decreasing tGTA; (tGTP>tGTA)
4-14
ISO2-CMOS MT8870D/MT8870D-1
Power-down and Inhibit Mode
Crystal Oscillator
Figure 6 - Differential Input Configuration
The internal clock circuit is completed with the
addition of an external 3.579545 MHz crystal and is
normally connected as shown in Figure 10 (Single- To OSC1 of next
Ended Input Configuration). However, it is possible to C MT8870D/MT8870D-1
configure several MT8870D/MT8870D-1 devices X-tal
employing only a single oscillator crystal. The OSC1 OSC2
oscillator output of the first device in the chain is
coupled through a 30 pF capacitor to the oscillator
input (OSC1) of the next device. Subsequent devices OSC2 OSC1
are connected in a similar fashion. Refer to Figure 7
C
for details. The problems associated with
unbalanced loading are not a concern with the
C=30 pF
arrangement shown, i.e., precision balancing X-tal=3.579545 MHz
capacitors are not required.
Figure 7 - Oscillator Connection
4-15
MT8870D/MT8870D-1 ISO2-CMOS
Applications
VDD
C1
DTMF C2
Input R1 MT8870D-1
IN+ VDD
IN- St/GT
GS ESt R3
R2 VRef StD
INH Q4
PWDN Q3
OSC 1 Q2 NOTES:
X1
OSC 2 Q1 R1 = 102KΩ ± 1%
VSS TOE R2 = 71.5KΩ ± 1%
R3 = 390KΩ ±1 %
C1,C2 = 100 nF ± 5%
X1 = 3.579545 MHz ± 0.1%
VDD = 5.0V ± 5%
4-16
ISO2-CMOS MT8870D/MT8870D-1
Recommended Operating Conditions - Voltages are with respect to ground (VSS) unless otherwise stated.
Parameter Sym Min Typ‡ Max Units Test Conditions
DC Electrical Characteristics - VDD=5.0V± 5%, VSS=0V, -40°C ≤ TO ≤ +85°C, unless otherwise stated.
Characteristics Sym Min Typ‡ Max Units Test Conditions
4-17
MT8870D/MT8870D-1 ISO2-CMOS
MT8870D AC Electrical Characteristics - VDD=5.0V ±5%, VSS=0V, -40°C ≤ TO ≤ +85°C , using Test Circuit shown in
Figure 10.
* NOTES
1. dBm= decibels above or below a reference power of 1 mW into a 600 ohm load.
2. Digit sequence consists of all DTMF tones.
3. Tone duration= 40 ms, tone pause= 40 ms.
4. Signal condition consists of nominal DTMF frequencies.
5. Both tones in composite signal have an equal amplitude.
6. Tone pair is deviated by ±1.5 %± 2 Hz.
7. Bandwidth limited (3 kHz ) Gaussian noise.
8. The precise dial tone frequencies are (350 Hz and 440 Hz) ± 2 %.
9. For an error rate of better than 1 in 10,000.
10. Referenced to lowest level frequency component in DTMF signal.
11. Referenced to the minimum valid accept level.
12. Guaranteed by design and characterization.
4-18
ISO2-CMOS MT8870D/MT8870D-1
MT8870D-1 AC Electrical Characteristics - VDD=5.0V±5%, VSS=0V, -40°C ≤ TO ≤ +85°C , using Test Circuit shown
in Figure 10.
* NOTES
1. dBm= decibels above or below a reference power of 1 mW into a 600 ohm load.
2. Digit sequence consists of all DTMF tones.
3. Tone duration= 40 ms, tone pause= 40 ms.
4. Signal condition consists of nominal DTMF frequencies.
5. Both tones in composite signal have an equal amplitude.
6. Tone pair is deviated by ±1.5 % ± 2 Hz.
7. Bandwidth limited (3 kHz ) Gaussian noise.
8. The precise dial tone frequencies are (350 Hz and 440 Hz) ± 2 %.
9. For an error rate of better than 1 in 10,000.
10. Referenced to lowest level frequency component in DTMF signal.
11. Referenced to the minimum valid accept level.
12. Referenced to Fig. 10 input DTMF tone level at -25dBm (-28dBm at GS Pin) interference frequency range between 480-3400Hz.
13. Guaranteed by design and characterization.
4-19
MT8870D/MT8870D-1 ISO2-CMOS
AC Electrical Characteristics - VDD=5.0V±5%, VSS=0V, -40°C ≤ To ≤ +85°C , using Test Circuit shown in Figure 10.
Characteristics Sym Min Typ‡ Max Units Conditions
*NOTES:
1. Used for guard-time calculation purposes only.
2. These, user adjustable parameters, are not device specifications. The adjustable settings of these minimums and maximums
are recommendations based upon network requirements.
3. With valid tone present at input, tPU equals time from PDWN going low until ESt going high.
VDD
C1
DTMF
Input C2
R1
MT8870D/MT8870D-1
IN+ VDD
IN- St/GT R3
GS ESt
R2
VRef StD
INH Q4
PDWN Q3
OSC 1 Q2 NOTES:
X-tal OSC 2 Q1 R1,R2=100KΩ ± 1%
R3=300KΩ ± 1%
VSS TOE
C1,C2=100 nF ± 5%
X-tal=3.579545 MHz ± 0.1%
4-20
ISO2-CMOS MT8870D/MT8870D-1
EVENTS A B C E F G
TONE TONE
Vin TONE #n #n + 1 #n + 1
tDP tDA
ESt
tGTP tGTA
VTSt
St/GT
tPQ
tQStD
HIGH IMPEDANCE
Q1-Q4 DECODED TONE # (n-1) #n # (n + 1)
tPSrD
StD
tPTE
tPTD
TOE
EXPLANATION OF EVENTS
A) TONE BURSTS DETECTED, TONE DURATION INVALID, OUTPUTS NOT UPDATED.
B) TONE #n DETECTED, TONE DURATION VALID, TONE DECODED AND LATCHED IN OUTPUTS
C) END OF TONE #n DETECTED, TONE ABSENT DURATION VALID, OUTPUTS REMIAN LATCHED UNTIL NEXT VALID
TONE.
D) OUTPUTS SWITCHED TO HIGH IMPEDANCE STATE.
E) TONE #n + 1 DETECTED, TONE DURATION VALID, TONE DECODED AND LATCHED IN OUTPUTS (CURRENTLY
HIGH IMPEDANCE).
F) ACCEPTABLE DROPOUT OF TONE #n + 1, TONE ABSENT DURATION INVALID, OUTPUTS REMAIN LATCHED.
G) END OF TONE #n + 1 DETECTED, TONE ABSENT DURATION VALID, OUTPUTS REMAIN LATCHED UNTIL NEXT
VALID TONE.
EXPLANATION OF SYMBOLS
Vin DTMF COMPOSITE INPUT SIGNAL.
ESt EARLY STEERING OUTPUT. INDICATES DETECTION OF VALID TONE FREQUENCIES.
St/GT STEERING INPUT/GUARD TIME OUTPUT. DRIVES EXTERNAL RC TIMING CIRCUIT.
Q1-Q4 4-BIT DECODED TONE OUTPUT.
StD DELAYED STEERING OUTPUT. INDICATES THAT VALID FREQUENCIES HAVE BEEN PRESENT/ABSENT FOR THE
REQUIRED GUARD TIME THUS CONSTITUTING A VALID SIGNAL.
TOE TONE OUTPUT ENABLE (INPUT). A LOW LEVEL SHIFTS Q1-Q4 TO ITS HIGH IMPEDANCE STATE.
tREC MAXIMUM DTMF SIGNAL DURATION NOT DETECED AS VALID
tREC MINIMUM DTMF SIGNAL DURATION REQUIRED FOR VALID RECOGNITION
tID MAXIMUM TIME BETWEEN VALID DTMF SIGNALS.
tDO MAXIMUM ALLOWABLE DROP OUT DURING VALID DTMF SIGNAL.
tDP TIME TO DETECT THE PRESENCE OF VALID DTMF SIGNALS.
tDA TIME TO DETECT THE ABSENCE OF VALID DTMF SIGNALS.
tGTP GUARD TIME, TONE PRESENT.
tGTA GUARD TIME, TONE ABSENT.
4-21
MT8870D/MT8870D-1 ISO2-CMOS
Notes:
4-22
Package Outlines
3 2 1
E1 E
n-2 n-1 n
A2 A
L C
eA eC
b2 e eB
Notes: b
D1
1) Not to scale
2) Dimensions in inches
3) (Dimensions in millimeters)
A2 0.115 (2.92) 0.195 (4.95) 0.115 (2.92) 0.195 (4.95) 0.115 (2.92) 0.195 (4.95) 0.115 (2.92) 0.195 (4.95)
b 0.014 (0.356) 0.022 (0.558) 0.014 (0.356) 0.022 (0.558) 0.014 (0.356) 0.022 (0.558) 0.014 (0.356) 0.022 (0.558)
b2 0.045 (1.14) 0.070 (1.77) 0.045 (1.14) 0.070 (1.77) 0.045 (1.14) 0.070 (1.77) 0.045 (1.14) 0.070 (1.77)
0.008 0.014 (0.356) 0.008 (0.203) 0.014(0.356) 0.008 (0.203) 0.014 (0.356) 0.008 (0.203) 0.014 (0.356)
C (0.203)
D 0.355 (9.02) 0.400 (10.16) 0.780 (19.81) 0.800 (20.32) 0.880 (22.35) 0.920 (23.37) 0.980 (24.89) 1.060 (26.9)
E 0.300 (7.62) 0.325 (8.26) 0.300 (7.62) 0.325 (8.26) 0.300 (7.62) 0.325 (8.26) 0.300 (7.62) 0.325 (8.26)
E1 0.240 (6.10) 0.280 (7.11) 0.240 (6.10) 0.280 (7.11) 0.240 (6.10) 0.280 (7.11) 0.240 (6.10) 0.280 (7.11)
e 0.100 BSC (2.54) 0.100 BSC (2.54) 0.100 BSC (2.54) 0.100 BSC (2.54)
eA 0.300 BSC (7.62) 0.300 BSC (7.62) 0.300 BSC (7.62) 0.300 BSC (7.62)
L 0.115 (2.92) 0.150 (3.81) 0.115 (2.92) 0.150 (3.81) 0.115 (2.92) 0.150 (3.81) 0.115 (2.92) 0.150 (3.81)
General-8
Package Outlines
3 2 1
E1 E
n-2 n-1 n
D
α
A2 A
L C
eA
b2 e eB
Notes: b
D1
1) Not to scale
2) Dimensions in inches
3) (Dimensions in millimeters)
A2 0.125 (3.18) 0.195 (4.95) 0.125 (3.18) 0.195 (4.95) 0.125 (3.18) 0.195 (4.95) 0.125 (3.18) 0.195 (4.95)
b 0.014 (0.356) 0.022 (0.558) 0.014 (0.356) 0.022 (0.558) 0.014 (0.356) 0.022 (0.558) 0.014 (0.356) 0.022 (0.558)
b2 0.045 (1.15) 0.070 (1.77) 0.030 (0.77) 0.070 (1.77) 0.030 (0.77) 0.070 (1.77) 0.030 (0.77) 0.070 (1.77)
C 0.008 (0.204) 0.015 (0.381) 0.008 (0.204) 0.015 (0.381) 0.008 (0.204) 0.015 (0.381) 0.008 (0.204) 0.015 (0.381)
D 1.050 (26.67) 1.120 (28.44) 1.150 (29.3) 1.290 (32.7) 1.380 (35.1) 1.565 (39.7) 1.980 (50.3) 2.095 (53.2)
E 0.390 (9.91) 0.430 (10.92) 0.600 (15.24) 0.670 (17.02) 0.600 (15.24) 0.670 (17.02) 0.600 (15.24) 0.670 (17.02)
E1 0.330 (8.39) 0.380 (9.65) 0.485 (12.32) 0.580 (14.73) 0.485 (12.32) 0.580 (14.73) 0.485 (12.32) 0.580 (14.73)
e 0.100 BSC (2.54) 0.100 BSC (2.54) 0.100 BSC (2.54) 0.100 BSC (2.54)
eA 0.400 BSC (10.16) 0.600 BSC (15.24) 0.600 BSC (15.24) 0.600 BSC (15.24)
eB 0.430 (10.92)
L 0.115 (2.93) 0.160 (4.06) 0.115 (2.93) 0.200 (5.08) 0.115 (2.93) 0.200 (5.08) 0.115 (2.93) 0.200 (5.08)
Pin 1
C
L
H
Notes:
D 1) Not to scale
2) Dimensions in inches
3) (Dimensions in millimeters)
A2
4) Ref. JEDEC Standard M0-150/M0118 for 48 Pin
5) A & B Maximum dimensions include allowable mold flash
A1
General-11
Package Outlines
Pin 1
C
L
H
e
D L
4 mils (lead coplanarity)
Notes:
1) Not to scale
A1 2) Dimensions in inches
3) (Dimensions in millimeters)
4) A & B Maximum dimensions include allowable mold flash
A 0.093 0.104 0.093 0.104 0.093 0.104 0.093 0.104 0.093 0.104
(2.35) (2.65) (2.35) (2.65) (2.35) (2.65) (2.35) (2.65) (2.35) (2.65)
A1 0.004 0.012 0.004 0.012 0.004 0.012 0.004 0.012 0.004 0.012
(0.10) (0.30) (0.10) (0.30) (0.10) (0.30) (0.10) (0.30) (0.10) (0.30)
B 0.013 0.020 0.013 0.030 0.013 0.020 0.013 0.020 0.013 0.020
(0.33) (0.51) (0.33) (0.51) (0.33) (0.51) (0.33) (0.51) (0.33) (0.51)
C 0.009 0.013 0.009 0.013 0.009 0.013 0.009 0.013 0.009 0.013
(0.231) (0.318) (0.231) (0.318) (0.231) (0.318) (0.231) (0.318) (0.231) (0.318)
D 0.398 0.413 0.447 0.4625 0.496 0.512 0.5985 0.614 0.697 0.7125
(10.1) (10.5) (11.35) (11.75) (12.60) (13.00) (15.2) (15.6) (17.7) (18.1)
E 0.291 0.299 0.291 0.299 0.291 0.299 0.291 0.299 0.291 0.299
(7.40) (7.40) (7.40) (7.40) (7.40) (7.40) (7.40) (7.40) (7.40) (7.40)
e 0.050 BSC 0.050 BSC 0.050 BSC 0.050 BSC 0.050 BSC
(1.27 BSC) (1.27 BSC) (1.27 BSC) (1.27 BSC) (1.27 BSC)
H 0.394 0.419 0.394 0.419 0.394 0.419 0.394 0.419 0.394 0.419
(10.00) (10.65) (10.00) (10.65) (10.00) (10.65) (10.00) (10.65) (10.00) (10.65)
L 0.016 0.050 0.016 0.050 0.016 0.050 0.016 0.050 0.016 0.050
(0.40) (1.27) (0.40) (1.27) (0.40) (1.27) (0.40) (1.27) (0.40) (1.27)
General-7
http://www.mitelsemi.com
Information relating to products and services furnished herein by Mitel Corporation or its subsidiaries (collectively “Mitel”) is believed to be reliable. However, Mitel assumes no
liability for errors that may appear in this publication, or for liability otherwise arising from the application or use of any such information, product or service or for any infringement of
patents or other intellectual property rights owned by third parties which may result from such application or use. Neither the supply of such information or purchase of product or
service conveys any license, either express or implied, under patents or other intellectual property rights owned by Mitel or licensed from third parties by Mitel, whatsoever.
Purchasers of products are also hereby notified that the use of product in certain ways or in combination with Mitel, or non-Mitel furnished goods or services may infringe patents or
other intellectual property rights owned by Mitel.
This publication is issued to provide information only and (unless agreed by Mitel in writing) may not be used, applied or reproduced for any purpose nor form part of any order or
contract nor to be regarded as a representation relating to the products or services concerned. The products, their specifications, services and other information appearing in this
publication are subject to change by Mitel without notice. No warranty or guarantee express or implied is made regarding the capability, performance or suitability of any product or
service. Information concerning possible methods of use is provided as a guide only and does not constitute any guarantee that such methods of use will be satisfactory in a specific
piece of equipment. It is the user’s responsibility to fully determine the performance and suitability of any equipment using such information and to ensure that any publication or
data used is up to date and has not been superseded. Manufacturing does not necessarily include testing of all functions or parameters. These products are not suitable for use in
any medical products whose failure to perform may result in significant injury or death to the user. All products and materials are sold and services provided subject to Mitel’s
conditions of sale which are available on request.