Documente Academic
Documente Profesional
Documente Cultură
Tests : The meters as specified in annex 2 were tested for compliance with the
standards as specified on page 1 of this test report. The performed
tests are stated in annex 1. If applicable specific test conditions are
stated at each test.
Traceability : The measurements have been executed using standards for which the
traceability to primary standards, (inter)national standards and/or
properties of pure substances has been demonstrated.
Remark : The test data as presented in the annex 4 of this test report is performed
under RvA accreditation with reference number L029, in which
conformity to ISO/IEC 17025 has been demonstrated.
The data as presented in the annexes 1, 2 and 3 gives extra
information and is not included in the scope of this accreditation.
Test report CVN-505035-02
Annex 1
Page 1 of 2
Particular requirements of the IEC 62053-21 / 62053-22 / 62053-23 as well as the Dutch regulations:
The EMC-tests and the diëlectric tests are performed at the TNO EPS BV laboratory
in Niekerk, the Netherlands.
Test report CVN-505035-02
Annex 2
Page 1 of 1
Remark: The results as mentioned in this test report relate only to the meters which are tested.
*) Model: MT830-D2A42R55S52-I1-M3K01Z4
**) Model: MT830-T1A32R45S52-I1-M3K01Z4
Error [%]
I [%] of Ib Sample nr. 2 Sample nr. 3
cos(φ)=1 cos(φ)=0,5 ind. cos(φ)=0,8 cap. cos(φ)=1 cos(φ)=0,5 ind. cos(φ)=0,8 cap.
5 + 0,1 + 0,2
10 + 0,1 – 0,0 – 0,1 + 0,2 – 0,0 + 0,1
20 – 0,0 – 0,0 – 0,0 + 0,1 + 0,1 + 0,1
50 – 0,0 – 0,2 – 0,0 + 0,0 – 0,1 + 0,1
100 – 0,1 – 0,2 – 0,0 + 0,0 – 0,1 + 0,1
150 – 0,0 – 0,2 + 0,0 + 0,1 – 0,1 + 0,1
200 – 0,0 – 0,2 + 0,0 + 0,1 – 0,1 + 0,1
0,2·Imax – 0,0 – 0,3 + 0,0 + 0,1 – 0,1 + 0,1
0,4·Imax + 0,0 – 0,2 + 0,0 + 0,1 – 0,2 + 0,1
0,6·Imax + 0,1 – 0,2 + 0,1 + 0,1 – 0,1 + 0,2
0,8·Imax + 0,1 – 0,1 + 0,1 + 0,2 – 0,1 + 0,3
Imax + 0,1 – 0,2 + 0,2 + 0,2 – 0,1 + 0,3
5 – 0,2 – 0,1
10 – 0,1 – 0,3 – 0,2 – 0,0 – 0,3 – 0,1
20 – 0,0 – 0,1 – 0,0 – 0,0 – 0,1 + 0,0
50 + 0,0 – 0,2 + 0,0 + 0,1 – 0,2 + 0,0
100 + 0,1 – 0,1 + 0,1 + 0,1 – 0,1 + 0,1
150 + 0,0 – 0,1 + 0,1 + 0,1 – 0,2 + 0,1
200 + 0,1 – 0,1 + 0,1 + 0,1 – 0,1 + 0,2
0,2·Imax + 0,1 – 0,0 + 0,2 + 0,1 – 0,1 + 0,2
0,4·Imax + 0,2 + 0,0 + 0,2 + 0,1 – 0,1 + 0,2
0,6·Imax + 0,2 – 0,2 + 0,2 + 0,2 – 0,0 + 0,2
0,8·Imax + 0,3 + 0,0 + 0,3 + 0,2 – 0,0 + 0,3
Imax + 0,3 – 0,0 + 0,3 + 0,3 – 0,1 + 0,4
Remark: Before the measurements were started, the voltage was connected for at least one hour
and a current of 0,1·Ib was running through the meters.
Test report CVN-505035-02
Annex 4
Page 2 of 54
Error [%]
I [%] of In Sample nr. 5 Sample nr. 6
cos(φ)=1 cos(φ)=0,5 ind. cos(φ)=0,8 cap. cos(φ)=1 cos(φ)=0,5 ind. cos(φ)=0,8 cap.
1 + 0,1 + 0,4
2 + 0,0 – 0,0 + 0,0 + 0,1 + 0,1 + 0,2
5 + 0,0 – 0,1 + 0,0 – 0,0 + 0,1 + 0,1
10 – 0,0 – 0,1 – 0,0 + 0,0 – 0,1 – 0,0
20 – 0,1 – 0,2 + 0,0 – 0,1 – 0,1 – 0,1
50 – 0,0 – 0,2 – 0,0 – 0,1 – 0,2 – 0,1
100 – 0,0 – 0,2 + 0,0 – 1,9 – 0,1 – 0,1
150 – 0,1 – 0,2 + 0,0 – 0,1 – 0,1 – 0,1
200 – 0,0 – 0,2 – 0,0 – 0,0 – 0,1 – 0,0
0,4·Imax – 0,0 – 0,1 – 0,1 – 0,1 – 0,6 – 0,0
0,6·Imax – 0,0 – 0,2 + 0,0 – 0,1 – 0,1 – 0,1
0,8·Imax + 0,0 – 0,2 + 0,0 – 0,1 – 0,1 – 0,0
Imax + 0,0 – 0,2 + 0,1 – 0,1 – 0,1 – 0,1
1 + 0,1 – 0,4
2 – 0,0 – 0,2 – 0,0 – 0,1 – 0,4 – 0,2
5 – 0,0 – 0,2 – 0,1 – 0,1 – 0,3 – 0,2
10 – 0,0 – 0,2 – 0,0 + 0,0 – 0,2 – 0,1
20 – 0,0 – 0,2 – 0,0 – 0,1 – 0,2 – 0,2
50 – 0,0 – 0,2 + 0,0 – 0,1 – 0,2 – 0,1
100 – 0,0 – 0,2 + 0,0 – 0,1 – 0,2 – 0,1
150 – 0,0 + 0,1 + 0,1 – 0,1 – 0,1 – 0,1
200 + 0,0 – 0,2 + 0,0 – 0,1 – 0,2 – 0,1
0,4·Imax + 0,0 – 0,1 + 0,0 – 0,1 – 0,1 – 0,1
0,6·Imax + 0,0 – 0,2 + 0,1 – 0,0 – 0,1 – 0,1
0,8·Imax – 0,0 – 0,2 + 0,0 – 0,1 – 0,1 – 0,0
Imax – 0,0 – 0,1 + 0,0 – 0,1 – 0,1 – 0,0
Remark: Before the measurements were started, the voltage was connected for at least one hour
and a current of 0,1·In was running through the meters.
Test report CVN-505035-02
Annex 4
Page 3 of 54
1 – 0,5 – 0,0
2 – 0,3 – 1,0 – 0,6 – 0,0 – 0,1 – 0,2
5 – 0,1 – 0,7 – 0,3 – 0,0 – 0,2 – 0,1
10 – 0,1 – 0,3 – 0,1 – 0,1 – 0,2 – 0,1
20 – 0,1 – 0,3 – 0,1 – 0,1 – 0,3 – 0,1
50 – 0,1 – 0,3 – 0,0 – 0,1 – 0,2 – 0,1
100 – 0,1 – 0,3 – 0,0 – 0,1 – 0,2 – 0,1
150 – 0,0 – 0,2 – 0,0 – 0,1 – 0,2 – 0,1
200 – 0,1 – 0,2 – 0,0 – 0,3 – 0,2 – 0,1
0,4·Imax – 0,0 – 0,2 + 0,0 – 0,1 – 0,2 – 0,0
0,6·Imax – 0,0 – 0,2 + 0,0 – 0,1 – 0,2 – 0,3
0,8·Imax – 0,0 – 0,2 + 0,0 – 0,1 – 0,2 – 0,0
Imax – 0,0 – 0,2 + 0,0 – 0,1 – 0,2 – 0,2
1 + 0,5 – 0,0
2 + 0,2 – 0,3 + 0,1 – 0,1 – 0,8 – 0,2
5 + 0,1 – 0,2 + 0,1 – 0,0 – 0,3 – 0,1
10 + 0,0 – 0,2 + 0,0 – 0,1 – 0,3 – 0,1
20 – 0,1 – 0,2 + 0,0 – 0,1 – 0,3 – 0,1
50 – 0,1 – 0,2 – 0,0 – 0,1 – 0,2 – 0,1
100 – 0,0 – 0,2 + 0,0 – 0,1 – 0,2 – 0,1
150 – 0,1 + 0,0 + 0,0 – 0,1 – 0,2 – 0,1
200 – 0,1 – 0,2 + 0,0 – 0,1 – 0,2 – 0,1
0,4·Imax – 0,0 – 0,2 + 0,0 – 0,1 – 0,2 – 0,0
0,6·Imax – 0,0 – 0,2 + 0,0 – 0,1 – 0,2 – 0,2
0,8·Imax – 0,0 – 0,2 + 0,0 – 0,1 – 0,2 – 0,1
Imax – 0,0 – 0,2 + 0,0 – 0,1 – 0,2 – 0,1
Remark: Before the measurements were started, the voltage was connected for at least one hour
and a current of 0,1·In was running through the meters.
Test report CVN-505035-02
Annex 4
Page 4 of 54
Error [%]
I [%] of Ib Sample nr. 2 Sample nr. 3
sin(φ)=1 sin(φ)=0,5 ind. sin(φ)=0,5 cap. sin(φ)=1 sin(φ)=0,5 ind. sin(φ)=0,5 cap.
5 + 0,5 + 0,0
10 + 0,3 + 0,6 + 0,2 – 0,0 + 0,1 – 0,4
20 + 0,1 + 0,4 + 0,1 – 0,1 + 0,1 – 0,3
50 + 0,1 + 0,3 – 0,1 – 0,1 + 0,1 – 0,4
100 + 0,1 + 0,3 – 0,1 – 0,1 + 0,2 – 0,3
150 + 0,1 + 0,4 – 0,1 – 0,0 + 0,0 – 0,3
200 + 0,1 + 0,4 – 0,1 – 0,0 + 0,2 – 0,3
0,2·Imax + 0,2 + 0,2 – 0,1 – 0,0 + 0,2 – 0,3
0,4·Imax + 0,2 + 0,4 – 0,1 – 0,0 + 0,2 – 0,3
0,6·Imax + 0,2 + 0,5 – 0,3 + 0,0 + 0,3 – 0,3
0,8·Imax + 0,2 + 0,5 – 0,1 + 0,1 + 0,4 – 0,3
Imax + 0,2 + 0,6 – 0,1 + 0,1 + 0,5 – 0,3
Error [%]
I [%] of Ib Sample nr. 2 Sample nr. 3
sin(φ)=1 sin(φ)=0,25 ind. sin(φ)=0,25 cap. sin(φ)=1 sin(φ)=0,25 ind. sin(φ)=0,25 cap.
Error [%]
I [%] of In Sample nr. 5 Sample nr. 6
sin(φ)=1 sin(φ)=0,5 ind. sin(φ)=0,5 cap. sin(φ)=1 sin(φ)=0,5 ind. sin(φ)=0,5 cap.
2 + 0,0 + 0,0
5 – 0,1 + 0,2 – 0,3 + 0,0 + 0,2 – 0,1
10 – 0,1 + 0,1 – 0,3 – 0,1 + 0,0 – 0,2
20 – 0,1 + 0,1 – 0,3 – 0,1 + 0,1 – 0,2
50 – 0,1 + 0,2 – 0,3 – 0,1 + 0,1 – 0,2
100 – 0,1 + 0,1 – 0,3 – 0,0 + 0,1 – 0,2
150 – 0,1 + 0,1 – 0,3 – 0,1 + 0,1 – 0,2
200 – 0,0 + 0,2 – 0,3 – 0,0 + 0,1 – 0,2
0,4·Imax – 0,1 + 0,2 – 0,3 – 0,0 + 0,1 – 0,2
0,6·Imax – 0,0 + 0,2 – 0,3 – 0,1 + 0,1 – 0,2
0,8·Imax – 0,0 + 0,2 – 0,3 – 0,0 + 0,1 – 0,3
Imax – 0,1 + 0,2 – 0,3 – 0,1 + 0,1 – 0,2
Error [%]
I [%] of In Sample nr. 5 Sample nr. 6
sin(φ)=1 sin(φ)=0,25 ind. sin(φ)=0,25 cap. sin(φ)=1 sin(φ)=0,25 ind. sin(φ)=0,25 cap.
Error [%]
I [%] of In Sample nr. 5 Sample nr. 6
sin(φ)=1 sin(φ)=0,25 ind. sin(φ)=0,25 cap. sin(φ)=1 sin(φ)=0,25 ind. sin(φ)=0,25 cap.
2 + 0,2 + 0,4
5 + 0,1 + 0,2 – 0,2 + 0,2 + 0,3 – 0,2
10 + 0,0 + 0,3 – 0,3 + 0,0 + 0,3 – 0,1
20 – 0,1 + 0,2 – 0,3 – 0,0 + 0,2 – 0,2
50 – 0,1 + 0,2 – 0,3 – 0,1 + 0,1 – 0,2
100 – 0,1 + 0,1 – 0,3 – 0,1 + 0,1 – 0,3
150 – 0,1 + 0,2 – 0,3 – 0,1 – 0,1 – 0,3
200 – 0,1 + 0,2 – 0,3 – 0,1 + 0,1 – 0,3
0,4·Imax – 0,1 + 0,2 – 0,3 – 0,1 + 0,1 – 0,2
0,6·Imax – 0,1 + 0,2 – 0,4 – 0,1 + 0,0 – 0,3
0,8·Imax – 0,1 + 0,2 – 0,3 – 0,1 + 0,1 – 0,3
Imax – 0,1 + 0,1 – 0,4 – 0,1 + 0,1 – 0,3
Error [%]
I [%] of In Sample nr. 5 Sample nr. 6
sin(φ)=1 sin(φ)=0,25 ind. sin(φ)=0,25 cap. sin(φ)=1 sin(φ)=0,25 ind. sin(φ)=0,25 cap.
Error [%]
I [%] of In Sample nr. 5 Sample nr. 6
sin(φ)=1 sin(φ)=0,25 ind. sin(φ)=0,25 cap. sin(φ)=1 sin(φ)=0,25 ind. sin(φ)=0,25 cap.
Error [%]
I [%] of Sample nr. 2
Ib cos(φ)=1 cos(φ)=0,5 ind.
R S T R S T
10 – 0,2 – 0,2 + 0,0
20 – 0,2 – 0,2 – 0,0 – 0,2 – 0,2 – 0,2
50 – 0,3 – 0,1 – 0,1 – 0,3 – 0,3 – 0,3
100 – 0,2 – 0,1 – 0,0 – 0,3 – 0,2 – 0,2
0,5·Imax + 0,1 + 0,1 + 0,2 + 0,2 – 0,1 – 0,1
Imax + 0,2 + 0,2 + 0,4 + 0,3 + 0,1 + 0,1
Error [%]
I [%] of Sample nr. 3
Ib cos(φ)=1 cos(φ)=0,5 ind.
R S T R S T
10 + 0,2 + 0,0 + 0,0
20 + 0,1 + 0,0 – 0,1 + 0,0 + 0,0 – 0,4
50 – 0,0 – 0,0 – 0,2 – 0,2 – 0,0 – 0,5
100 + 0,0 + 0,0 – 0,2 – 0,1 + 0,1 – 0,5
0,5·Imax + 0,4 + 0,2 + 0,0 + 0,4 + 0,2 – 0,2
Imax + 0,5 + 0,3 + 0,2 + 0,6 + 0,2 – 0,1
Sample nr. 2
I [%] of Error [%]
Ib sin(φ)=1 sin(φ)=0,5 ind. sin(φ)=0,5 cap.
R S T R S T R S T
10 – 0,9 + 0,3 + 1,1
20 – 0,6 + 0,3 + 0,5 – 0,6 + 0,6 + 1,2 – 1,0 + 0,1 + 0,8
50 – 0,5 + 0,3 + 0,2 – 0,3 + 0,5 + 0,5 – 0,8 + 0,0 + 0,2
100 – 0,4 + 0,3 + 0,1 – 0,2 + 0,6 + 0,4 – 0,6 + 0,1 + 0,0
0,5·Imax + 0,0 + 0,5 + 0,2 + 0,4 + 0,9 + 0,7 – 0,1 + 0,2 + 0,0
Imax + 0,1 + 0,6 + 0,4 + 0,6 + 1,2 + 0,9 + 0,1 + 0,5 + 0,2
Sample nr. 3
I [%] of Error [%]
Ib sin(φ)=1 sin(φ)=0,5 ind. sin(φ)=0,5 cap.
R S T R S T R S T
10 – 1,0 + 0,1 + 0,5
20 – 0,6 – 0,1 + 0,1 – 0,7 + 0,1 + 0,8 – 1,3 – 0,1 + 0,2
50 – 0,4 – 0,2 – 0,1 – 0,2 – 0,0 + 0,3 – 0,9 – 0,3 – 0,2
100 – 0,3 – 0,2 – 0,1 – 0,0 – 0,1 + 0,3 – 0,7 – 0,3 – 0,3
0,5·Imax + 0,1 – 0,1 + 0,1 + 0,5 + 0,3 + 0,6 + 0,0 – 0,2 – 0,1
Imax + 0,2 + 0,0 + 0,3 + 0,9 + 0,4 + 0,9 + 0,2 – 0,1 + 0,1
Test report CVN-505035-02
Annex 4
Page 8 of 54
Error [%]
I [%] of Sample nr. 5
In cos(φ)=1 cos(φ)=0,5 ind.
R S T R S T
5 – 0,1 – 0,1 + 0,1
10 – 0,1 – 0,1 + 0,0 – 0,4 – 0,1 – 0,0
50 – 0,1 – 0,0 + 0,0 – 0,4 – 0,1 – 0,1
100 – 0,1 – 0,1 + 0,0 – 0,8 – 0,1 – 0,1
0,5·Imax – 0,1 + 0,0 + 0,0 – 0,3 – 0,1 – 0,1
Imax – 0,0 – 0,1 + 0,0 – 0,4 – 0,1 – 0,1
Error [%]
I [%] of Sample nr. 6
In cos(φ)=1 cos(φ)=0,5 ind.
R S T R S T
5 – 0,1 – 0,1 + 0,1
10 – 0,1 – 0,1 – 0,0 – 0,1 – 0,1 + 0,0
50 – 0,2 – 0,1 – 0,1 – 0,2 – 0,3 – 0,1
100 – 0,1 – 0,1 + 0,0 – 0,1 – 0,2 – 0,1
0,5·Imax – 0,1 – 0,1 – 0,1 – 0,1 – 0,2 + 0,0
Imax – 0,1 – 0,0 – 0,0 – 0,0 – 0,2 – 0,1
Sample nr. 5
I [%] of Error [%]
In sin(φ)=1 sin(φ)=0,5 ind. sin(φ)=0,5 cap.
R S T R S T R S T
5 – 0,2 – 0,3 + 0,1
10 – 0,1 – 0,2 + 0,2 + 0,3 – 0,1 + 0,1 – 0,6 – 0,4 + 0,0
20 – 0,6 – 0,2 + 0,1 + 0,2 – 0,1 + 0,2 – 0,7 – 0,4 + 0,1
100 – 0,1 – 0,1 + 0,0 + 0,3 – 0,0 + 0,1 – 0,5 – 0,2 – 0,1
0,5·Imax – 0,1 – 0,1 + 0,0 + 0,4 + 0,1 + 0,1 – 0,5 – 0,2 – 0,0
Imax – 0,1 – 0,1 + 0,0 + 0,4 + 0,1 + 0,1 – 0,5 – 0,2 – 0,0
Sample nr. 6
I [%] of Error [%]
In sin(φ)=1 sin(φ)=0,5 ind. sin(φ)=0,5 cap.
R S T R S T R S T
5 – 0,1 – 0,2 + 0,1
10 – 0,1 – 0,2 + 0,1 + 0,1 + 0,1 – 0,0 – 0,2 – 0,5 + 0,1
20 – 0,1 – 0,2 + 0,0 + 0,1 – 0,1 + 0,1 – 0,3 – 0,4 + 0,1
100 – 0,0 – 0,1 – 0,0 + 0,2 + 0,0 – 0,0 – 0,2 – 0,3 – 0,0
0,5·Imax + 0,0 – 0,1 – 0,0 + 0,2 + 0,1 + 0,0 – 0,2 – 0,3 – 0,0
Imax + 0,0 – 0,1 – 0,0 + 0,2 + 0,1 + 0,0 – 0,2 – 0,3 + 0,0
Test report CVN-505035-02
Annex 4
Page 9 of 54
Sample nr. 5
I [%] of Error [%] with 3x57,7/100V
In sin(φ)=1 sin(φ)=0,5 ind. sin(φ)=0,5 cap.
R S T R S T R S T
5 + 0,1 – 0,1 + 0,5
10 – 0,0 – 0,1 + 0,2 + 0,5 + 0,1 + 0,6 – 0,7 – 0,3 – 0,0
100 – 0,1 – 0,1 – 0,1 + 0,3 + 0,1 + 0,1 – 0,5 – 0,3 – 0,2
0,5·Imax – 0,1 – 0,1 – 0,1 + 0,3 + 0,1 + 0,1 – 0,5 – 0,3 – 0,2
Imax – 0,1 – 0,1 – 0,1 + 0,1 + 0,1 + 0,1 – 0,5 – 0,3 – 0,2
Sample nr. 6
I [%] of Error [%] with 3x57,7/100V
In sin(φ)=1 sin(φ)=0,5 ind. sin(φ)=0,5 cap.
R S T R S T R S T
5 + 0,2 + 0,1 + 0,4
10 + 0,0 – 0,0 + 0,2 + 0,3 + 0,2 + 0,5 – 0,4 – 0,4 – 0,0
100 – 0,1 – 0,1 – 0,1 + 0,0 + 0,1 + 0,0 – 0,4 – 0,3 – 0,1
0,5·Imax – 0,1 – 0,1 – 0,1 + 0,1 + 0,1 + 0,0 – 0,3 – 0,3 – 0,2
Imax – 0,1 – 0,1 – 0,1 + 0,1 + 0,1 + 0,1 – 0,2 – 0,3 – 0,2
Test report CVN-505035-02
Annex 4
Page 10 of 54
Sample nr. 2
No-load condition with no current and a tension of 80% and
√
115% of the reference voltage
Registration checked at % of Ib 0,4 %
Sample nr. 3
No-load condition with no current and a tension of 80% and
√
115% of the reference voltage
Registration checked at % of Ib 0,4 %
Sample nr. 2
No-load condition with no current and a tension of 80% and
√
115% of the reference voltage
Registration checked at % of Ib 0,4 %
Sample nr. 3
No-load condition with no current and a tension of 80% and
√
115% of the reference voltage
Registration checked at % of Ib 0,4 %
Sample nr. 5
No-load condition with no current and a tension of 80% and
√
115% of the reference voltage
Registration checked at % of In 0,1 %
Registration checked at % of In with export energy 0,1 %
Sample nr. 6
No-load condition with no current and a tension of 80% and
√
115% of the reference voltage
Registration checked at % of In 0,1 %
Registration checked at % of In with export energy 0,1 %
Sample nr. 5
No-load condition with no current and a tension of 80% and
√
115% of the reference voltage
Registration checked at % of In 0,1 %
Registration checked at % of In with export energy 0,1 %
Sample nr. 6
No-load condition with no current and a tension of 80% and
√
115% of the reference voltage
Registration checked at % of In 0,1 %
Registration checked at % of In with export energy 0,1 %
Sample nr. 2
Ib
percentage of Uref power factor variation [%]
1 + 0,0
115
0,5 ind. – 0,0
1 – 0,1
110
0,5 ind. – 0,1
1 – 0,0
90
0,5 ind. – 0,1
1 + 0,0
80
0,5 ind. – 0,1
1 + 0,1
22
0,5 ind. – 0,0
1 no registration
<22
0,5 ind. no registration
Sample nr. 3
Ib
percentage of Uref power factor variation [%]
1 – 0,0
115
0,5 ind. + 0,0
1 – 0,0
110
0,5 ind. – 0,0
1 – 0,0
90
0,5 ind. – 0,0
1 + 0,0
80
0,5 ind. + 0,0
1 + 0,0
22
0,5 ind. + 0,0
1 no registration
<22
0,5 ind. no registration
Sample nr. 2
Ib
percentage of Uref power factor variation [%]
115 1 + 0,0
0,5 ind. – 0,0
0,5 cap. – 0,0
110 1 + 0,0
0,5 ind. + 0,0
0,5 cap. – 0,0
90 1 + 0,0
0,5 ind. + 0,0
0,5 cap. + 0,0
80 1 + 0,0
0,5 ind. + 0,0
0,5 cap. – 0,0
22 1 + 0,1
0,5 ind. + 0,2
0,5 cap. + 0,2
<22 1 meter
0,5 ind. shuts
0,5 cap. down
Sample nr. 3
Ib
percentage of Uref power factor variation [%]
115 1 – 0,0
0,5 ind. + 0,0
0,5 cap. – 0,1
110 1 + 0,0
0,5 ind. + 0,1
0,5 cap. – 0,0
90 1 + 0,0
0,5 ind. + 0,1
0,5 cap. + 0,0
80 1 + 0,0
0,5 ind. + 0,0
0,5 cap. + 0,0
22 1 + 0,2
0,5 ind. + 0,2
0,5 cap. + 0,2
<22 1 meter
0,5 ind. shuts
0,5 cap. down
Sample nr. 2
Variation at frequency
Uref
49 Hz 51 Hz
I=0,1Ib, cos(φ)=1 + 0,0 – 0,1
I=0,5Imax, cos(φ)=1 + 0,1 – 0,0
I=0,5Imax, cos(φ)=0,5 ind. + 0,2 – 0,1
Sample nr. 3
Variation at frequency
Uref
49 Hz 51 Hz
I=0,1Ib, cos(φ)=1 – 0,0 – 0,1
I=0,5Imax, cos(φ)=1 + 0,2 + 0,1
I=0,5Imax, cos(φ)=0,5 ind. + 0,1 + 0,0
Sample nr. 2
Variation at frequency
Uref
47,5 Hz 52,5 Hz
I=0,1Ib, cos(φ)=1 – 0,0 + 0,1
I=0,5Imax, cos(φ)=1 + 0,1 + 0,0
I=0,5Imax, cos(φ)=0,5 ind. + 0,1 + 0,1
Sample nr. 3
Variation at frequency
Uref
47,5 Hz 52,5 Hz
I=0,1Ib, cos(φ)=1 + 0,0 + 0,1
I=0,5Imax, cos(φ)=1 + 0,1 + 0,1
I=0,5Imax, cos(φ)=0,5 ind. + 0,1 + 0,1
Sample nr. 2
Variation at frequency
Uref
49 Hz 51 Hz
I=0,1Ib, sin(φ)=1 – 0,1 – 0,1
I=0,5Imax, sin(φ)=1 – 0,0 + 0,0
I=0,5Imax, sin(φ)=0,5 ind. – 0,0 + 0,0
I=0,5Imax, sin(φ)=0,5 cap. + 0,0 + 0,0
Sample nr. 3
Variation at frequency
Uref
49 Hz 51 Hz
I=0,1Ib, sin(φ)=1 – 0,1 – 0,1
I=0,5Imax, sin(φ)=1 – 0,0 + 0,0
I=0,5Imax, sin(φ)=0,5 ind. – 0,0 + 0,0
I=0,5Imax, sin(φ)=0,5 cap. – 0,1 + 0,0
Results:
Sample nr. 2
I [%] of Ib
balanced load single phase load
10 100 Imax 50 R 50 S 50 T
error with RST sequence [%] + 0,01 – 0,02 + 0,15 – 0,25 – 0,12 – 0,05
error with RTS sequence [%] – 0,04 – 0,03 + 0,11 – 0,25 – 0,10 – 0,06
variation [%] – 0,05 – 0,01 – 0,04 + 0,00 + 0,02 – 0,01
Sample nr. 3
I [%] of Ib
balanced load single phase load
10 100 Imax 50 R 50 S 50 T
error with RST sequence [%] + 0,17 + 0,07 + 0,27 – 0,01 + 0,00 – 0,17
error with RTS sequence [%] + 0,11 + 0,07 + 0,23 + 0,03 + 0,02 – 0,21
variation [%] – 0,06 + 0,00 – 0,04 + 0,04 + 0,02 – 0,04
Definition: Variation = (Error with RTS sequence) - (Error with RST sequence)
Test report CVN-505035-02
Annex 4
Page 21 of 54
Results:
Sample nr. 2
interruption of phase R S T RS RT ST N
error with balanced load [%] + 0,05
error without phase [%] + 0,07 – 0,03 + 0,02 – 0,03 + 0,21 – 0,25 + 0,04
variation [%] + 0,02 – 0,08 – 0,03 – 0,08 + 0,16 – 0,30 – 0,01
Sample nr. 3
interruption of phase R S T RS RT ST N
error with balanced load [%] + 0,08
error without phase [%] + 0,00 + 0,15 + 0,01 + 0,00 – 0,09 – 0,04 + 0,08
variation [%] – 0,08 + 0,07 – 0,07 – 0,08 – 0,17 – 0,12 + 0,00
Sample nr. 4
Sample nr. 4
Sample nr. 4
Sample nr. 4
Definition: Variation = (Error with operation of accessories) - (Error without operation of accessories)
Test report CVN-505035-02
Annex 4
Page 23 of 54
Sample nr. 3
Variation at temperature Max. temperature
Uref
-40°C -20°C 0°C 40°C 60°C coefficient %/K
I=0,1Ib, cos(φ)=1 – 0,2 – 0,2 – 0,1 + 0,1 + 0,2 0,007
I=0,2Ib, cos(φ)=0,5 ind. – 0,1 – 0,1 – 0,0 + 0,1 + 0,2 0,006
I=Ib, cos(φ)=1 – 0,1 – 0,1 + 0,1 + 0,2 + 0,3 0,008
I=Ib, cos(φ)=0,5 ind. + 0,1 – 0,0 + 0,1 + 0,1 + 0,2 0,007
I=Imax, cos(φ)=1 – 0,1 – 0,1 + 0,1 + 0,2 + 0,3 0,009
I=Imax, cos(φ)=0,5 ind. + 0,1 + 0,0 + 0,0 + 0,1 + 0,1 0,005
Remark: Instead of the prescribed 20 K range (see par. 8.2, remark 9, of the IEC 62053-21), the above
mentioned temperatures are used.
Sample nr. 3
Variation at temperature Max. temperature
Uref
-40°C -20°C 0°C 40°C 60°C coëfficiënt %/K
I=0,1Ib, sin(φ)=1 + 0,6 + 0,2 + 0,1 + 0,1 + 0,4 0,020
I=0,2Ib, sin(φ)=0,5 ind. + 0,4 + 0,1 + 0,0 + 0,2 + 0,5 0,016
I=0,2Ib, sin(φ)=0,5 cap. + 0,8 + 0,4 + 0,2 + 0,2 + 0,4 0,021
I=Ib, sin(φ)=1 + 0,0 – 0,0 – 0,0 + 0,1 + 0,3 0,007
I=Ib, sin(φ)=0,5 ind. – 0,1 – 0,1 – 0,1 + 0,2 + 0,3 0,008
I=Ib, sin(φ)=0,5 cap. + 0,3 + 0,1 + 0,1 + 0,1 + 0,2 0,008
I=Imax, sin(φ)=1 – 0,0 – 0,1 – 0,0 + 0,1 + 0,2 0,006
I=Imax, sin(φ)=0,5 ind. – 0,2 – 0,2 – 0,1 + 0,2 + 0,3 0,008
I=Imax, sin(φ)=0,5 cap. + 0,1 + 0,0 + 0,0 + 0,1 + 0,2 0,005
Remark: Instead of the prescribed 20 K range (see par. 8.2, remark 7, of the IEC 62053-23), the above
mentioned temperatures are used.
Test report CVN-505035-02
Annex 4
Page 24 of 54
Sample nr. 6
Variation at temperature Max. temperature
Uref
-40°C -20°C 0°C 40°C 60°C coefficient %/K
I=0,05In, cos(φ)=1 – 0,0 – 0,0 – 0,0 + 0,1 + 0,1 0,004
I=0,1In, cos(φ)=0,5 ind. – 0,0 – 0,0 + 0,0 + 0,1 + 0,1 0,003
I=In, cos(φ)=1 + 0,1 + 0,0 + 0,0 + 0,1 + 0,0 0,006
I=In, cos(φ)=0,5 ind. + 0,2 + 0,1 + 0,1 + 0,1 + 0,0 0,007
I=Imax, cos(φ)=1 + 0,1 + 0,0 – 0,0 + 0,0 + 0,0 0,007
I=Imax, cos(φ)=0,5 ind. + 0,2 + 0,0 + 0,0 + 0,0 + 0,0 0,008
Remark: Instead of the prescribed 20 K range (see par. 8.2, remark 9, of the IEC 62053-22), the above
mentioned temperatures are used.
Sample nr. 6
Variation at temperature Max. temperature
Uref
-40°C -20°C 0°C 40°C 60°C coëfficiënt %/K
I=0,05In, sin(φ)=1 + 0,6 + 0,3 + 0,1 + 0,0 + 0,1 0,014
I=0,1In, sin(φ)=0,5 ind. + 0,6 + 0,3 + 0,1 + 0,0 + 0,1 0,014
I=0,1In, sin(φ)=0,5 cap. + 0,6 + 0,3 + 0,1 + 0,0 + 0,1 0,015
I=In, sin(φ)=1 + 0,1 + 0,1 + 0,0 + 0,0 + 0,1 0,004
I=In, sin(φ)=0,5 ind. + 0,1 + 0,1 + 0,0 + 0,0 + 0,1 0,003
I=In, sin(φ)=0,5 cap. + 0,2 + 0,1 + 0,0 + 0,0 + 0,1 0,003
I=Imax, sin(φ)=1 + 0,1 + 0,1 + 0,0 + 0,0 + 0,1 0,003
I=Imax, sin(φ)=0,5 ind. + 0,1 + 0,0 + 0,0 + 0,0 + 0,1 0,003
I=Imax, sin(φ)=0,5 cap. + 0,1 + 0,1 + 0,0 + 0,0 + 0,1 0,004
Remark: Instead of the prescribed 20 K range (see par. 8.2, remark 7, of the IEC 62053-23), the above
mentioned temperatures are used.
Test report CVN-505035-02
Annex 4
Page 25 of 54
DC and even harmonics in the a.c. current circuit (half wave rectification):
DC and even harmonics in the a.c. current circuit (half wave rectification):
Results: The influence due to the continuous magnetic field was negligible.
The meter was functioning correctly when applying the magnetic field, with
both active and reactive energy.
Test report CVN-505035-02
Annex 4
Page 29 of 54
Sample nr. 4
Sample nr. 4
Definition: Variation = (Error with an external magnetic field) - (Error at reference conditions)
Results: The difference in the error of indication at reference conditions before and after
the test was not greater than the uncertainty of the measurements, with both
active and reactive energy.
Test report CVN-505035-02
Annex 4
Page 32 of 54
During the test cables are used with an area of 25 square mm.
Remark: Before the measurements were started, the voltage was connected for at least
2 hours.
Test report CVN-505035-02
Annex 4
Page 33 of 54
Remark: Before the measurements were started, the voltage was connected for at least
2 hours.
Test report CVN-505035-02
Annex 4
Page 34 of 54
The test is performed with each circuit. The impulse voltage is applied ten
times with one polarity and then repeated with the other polarity.
The minimum time between the impulses was 3 s.
b) AC voltage test
The AC voltage test is performed with a r.m.s. test voltage of 4 kV.
b) AC voltage test
During the test no flashover, disruptive discharge or puncture occurred.
The difference in the error of indication at reference conditions before and after
the test was not greater than the uncertainty of the measurements.
No mechanical damage occurred to the meter.
Remark: During the test with 6 kV according to IEC 62052-11 the following auxilliary
circuits are investigated:
- CS and external power supply *)
*) The external power supply was not used to power the meter during
the tests.
Test report CVN-505035-02
Annex 4
Page 35 of 54
The tests are performed with reference voltage, with sample nr. 1.
Remark: During the test the following auxilliary circuits were connected:
- CS and external power supply *)
*) The external power supply was not used to power the meter during
the tests.
Test report CVN-505035-02
Annex 4
Page 37 of 54
Besides the stated peak value, the fast transient bursts had the following
characteristics:
Remark: During the test the following auxilliary circuits were connected:
- CS and external power supply *)
*) The external power supply was not used to power the meter during
the tests.
Test report CVN-505035-02
Annex 4
Page 38 of 54
The tests are performed with reference voltage, with sample nr. 1.
Remark: During the test the following auxilliary circuits were connected:
- CS and external power supply *)
*) The external power supply was not used to power the meter during
the tests.
Test report CVN-505035-02
Annex 4
Page 39 of 54
At each test the emission is measured under the following conditions of the
watthourmeter:
- with reference voltage;
- 10% of the basic current.
Remark: The cables have been manipulated in such a way that maximum disturbance
levels have been recorded.
Test report CVN-505035-02
Annex 4
Page 43 of 54
Results: During the tests a, b and c the content of the register is not changed,
for both active and reactive energy.
Test report CVN-505035-02
Annex 4
Page 46 of 54
The dry heat and cold test are performed with sample nr. 4.
The damp heat, cyclic test is performed with sample nr. 1.
Result: The meter case was not damaged; no affection of the meter functions took place.
After the test it was not possible to touch live parts.
Result: Ingress of dust and water of any quantity to impair the operation of the meter has
not been detected. The insulation strength test in accordance with par. 5.4.6 has
been carried out and no performance degradation of the insulation properties was
detected.
Result: At 650 °C there was no flame. At 960 °C there was a flame but it extinguished < 5 sec.
Test report CVN-505035-02
Annex 4
Page 50 of 54
Test: Stability
The error is checked during 10 consecutive measurements of 4 minutes under
reference conditions at 10% of the basic current.
Results:
0,1 Ib
Uref
Results:
Sample nr. 3
Definition: Variation = (Error with a harmonic in the current) - (Error at reference conditions)
Test report CVN-505035-02
Annex 4
Page 52 of 54
Results:
Sample nr. 3
Uref, cos(φ)=1
0,05 Ib Ib
error without DC-component [%] – 0,04 – 0,16
error with DC-component [%] + 0,06 – 0,11
variation [%] + 0,10 + 0,05
Definition: Variation = (Error with a DC-component in the current) - (Error at reference conditions)
Test report CVN-505035-02
Annex 4
Page 53 of 54
sample nr. 3
Results:
phases R S T RS RT ST RST
error with tension drops [%] + 0,00 – 0,16 – 1,85 + 0,01 + 0,08 – 1,88 – 2,51
sample nr. 4
phases R S T RS RT ST RST
error without tension drops [%] – 0,12
error with tension drops [%] – 0,07 – 0,14 – 1,35 – 0,05 – 1,39 – 1,48 – 1,69
variation [%] + 0,05 – 0,02 – 1,23 + 0,07 – 1,27 – 1,36 – 1,57
Measurement without any current: no impulses of the pulse output are measured.
Test report CVN-505035-02
Annex 4
Page 54 of 54
Results: