Sunteți pe pagina 1din 25

1.0.

DIGITAL SWITCHING CONCEPTS:Telephony was invented in 1876 and automatic telephone exchanges were

developed in 1895.All these exchanges were analog.Now we have only digital exchanges in the network,which work on time switching or time and space switching.The digital exchanges are compatible to provide value added services and Intelligent services. Communication can be defined as the transfer of information from one point to another point as per desire of the user under the control of some system.

The key aspects of a communication network are:

1.Switching 2.Transmission 3.Call control or signaling 4.End terminals or network elements

2.0.

SWITCHING:Switching is basically estabilishing temporary path or connection between two

points or it can also be defined as writing at one point of time and reading at another point of time. There are two modes of switching employed in our network. y y Circuit Switching Packet Switching

2.1.

CIRCUIT SWITCHING:In normal telephone service,basically,a circuit between the calling party and

called party is set up and this circuit is kept reserved till the call is completed.Here two speech time slots are involved,one of calling subscriber,other of called subscriber.It is called CIRCUIT SWITCHING. Circuit switching is based on the principle of SAMPLING THEOREM.

1|P ag e

2.1.1. SAMPLING THEOREM:Sampling Theorem states If a band limited signal is sampled at regular intervals of time and at a rate equal to or more than twice the highest signal frequency in the band,then the sample contains all the information of the original signal.Mathematically,if fh is the highest frequency then sampling frequency Fs needs to be greater than or equal to 2fh. i.e; Fs>=2 fh.

2.2.

PACKET SWITCHING:In packet switching,the information(speech,data etc.) is divided into packets,

each packet containing piece of information also bears source and destination address.These packets are sent independently through the network with the destination address embedded in them.Each packet may follow different path depending upon the network.

3.0.

SWITCHING CONCEPT:To connect any two subscribers,it is necessary to interconnect the time-slots of the two speech samples which may be on same or different PCM highways. The digitized speech samples are switched in two modes:

. Time Switching . Space switching 3.1. TIME SWITCHING:A Digital Time Switch consists of two memories,viz,a speech or buffer memory to store the samples till destination time-slots arrive,and a control or connection or address memory to control the writing and reading of the samples in the buffer memory and directing them on to the appropriate time-slots. Speech memory has as many storage locations as the number of time slots in input PCM,e.g; 32 locations for 32 channel PCM system.

2|P ag e

3.2.

SPACE SWITCHING:A space switch is used to simply change the PCM of a incoming time slot keeping the time slot number same in the outgoing PCM.

4.0. SWITCHING TECHNOLOGIES OF BSNL:OCB-283 EWSD 5ESS AXE-10 C-DOT E-10B

y y y y y y

3|P ag e

5.0.

EWSD: AN OVERVIEW:Communications networks are changing rapidly, placing vast new demands on switching systems. Once single-function machines designed simply to connect voice circuits, central office switches must now deliver a wide range of services, create customized services on demand, and manage network operations. In addition to these changes in functionality, changes to how these switches are deployed have also taken place. Once locked into central offices, they are now distributed into numerous network nodes, close to communications users and customized to the end users' needs. EWSD Digital switching system has been designed and manufactured by M/s Siemens, Germany. The name is the abbreviated form of German equivalent of Electronic Switching System Digital (Electronische Wheler Systeme Digitale). EWSD switch can support maximum 2,50,000 subscribers or 60,000 incoming, outgoing or both way trunks, when working as a pure tandem exchange. It can carry 25,200 Erlang traffic and can withstand 1.4 million BHCA. It is claimed that with the latest hardware and software version (Ver. 16), the system can withstand a BHCA of 16 million , can connect 6,50,000 subscribers or 2,40,000 trunks and handle 1,00,800 Erlang traffic. It can work as local cum transit exchange and supports CCS No.7, ISDN and IN and V5.X features.

4|P ag e

5.1.

EWSD: BLOCK DIAGRAM:-

DLU LINES TRUNKS CCNC

LTG(B)

LTG(C)

SN MB

SYP

CP CCG

OMT MDD MOD

PRINTER

6.0.

SYSTEM ARCHITECTURE:6.1)DIGITAL LINE UNIT(DLU):It is a functional unit on which analog and digital subscribers (ISDN-BRI) lines are terminated. DLUs are connected to EWSD sub-systems via a uniform interface standardized by CCITT, i.e., Primary Digital Carrier (PDC) to facilitate Local or Remote connection of subscriber lines. A subset of CCS# 7 is used for CCS on the PDCs. One DLU is connected to two different LTGs for the reasons of security. A local DLU is connected to two LTGs via two 4 Mbps (64 TSs) links, each towards a different LTG. In case of remote DLUs, maximum 4 PDCs of 2 Mbps (32 TSs) are used per DLU, two towards each LTG (PDC0 & PDC1 from DLU System 0, PDC2 &PDC3 from DLU System 1. Signaling information is carried in TS16 of PDC0 and PDC2. In case of a local DLU interface, TS32 carries the signaling information.

5|P ag e

In case the link between a remote DLU and the main exchange is broken,the subscribers connected to the remote DLU can still dial each other but metering will not be possible in this case.

6.1.1) PRINCIPLE FEATURES OF DLU:. Connection capacity of a rack: -Upto 952 analog subscriber lines -Upto 928 digital subscriber lines(ISDN basic access) -16 x 2 V5.1 interfaces

. Line types: The following analog line types can be connected: - subscriber lines (individual lines) with rotary dialing, DTMF dialing, subscriber's private meter operating at 16/12 kHz. payphones (coinbox) analog PBXs with/without direct dialing

The following digital line types can be connected: ISDN basic access small and medium-sized PBXs
Expansion capability:-

In small modular increments which consist of adding one analog subscriber line module (SLMA), which may be equipped with 4, 6 or 8 analog subscriber line circuits (SLCA), according to line type one digital subscriber line module containing 8 digital subscriber line circuits (SLCD) one subscriber line module (SLMX) for two V5.1 interfaces, each with 30 subscribers (Access Network (AN)) Signaling:Via common channel signaling (CCS) for transmission of control information between the DLU and line/trunk groups (LTGs). Channel 16 is used in both

6|P ag e

directions for signaling. For the local DLU interface, channel 32 is used for CCS on both 4096-kbit/s links. High reliability:A high level of reliability is ensured by: connecting each DLU to two LTGs duplicating all DLU units performing central functions, with load sharing continuous self tests

6.1.2) STRUCTURE OF DLU:Subscriber lines and PBX lines in EWSD are connected to digital line units (DLU). (Fig. 1) The DLUs can be operated locally in an exchange or remotely (Fig.2). The DLUs are connected to the Switching Network via LTG(B-function). A remote DLU is connected to an LTG by 2 Mbps Primary Digital Carriers (PDC). However, the local DLUs ( the DLUs located in the main exchange ) are connected to the LTG(B) by 4 Mbps carriers. For security reasons, a DLU is connected to two LTGs. A subset of CCS#7 according to CCITT is used for signaling between a DLU and the Group Processor (GP) in the two LTGs. Remote DLUs are installed in the vicinity of groups of subscribers. The resultant short subscriber lines and the flexible concentration of subscriber traffic to the exchange onto digital transmission links makes for an economical subscriber line network with optimum transmission quality.

7|P ag e

Analog 2 wire interface for a/b connection

DLU Concentration of the subscriber accesses

y y

Analog subscribers Small PSTN P(A)BX

a/b or

Analog/digital conversion for analog subscribers Modules


SLM for the connection of - a/b interfaces (SLMA with 8 or 16 subscriber line circuits - SLCA) - U interfaces (SLMD with 8 or 16 subscriber line circuits - SLCD)

Digital 2 wire interface for basic access (BA) y y Digital subscribers Small ISDN P(A)BX

U or

Fig. 1

8|P ag e

DLU

LTG

DLU

LTG

Fig2. Structure of DLU interface with LTG

9|P ag e

6.1.3) DLU H/W TYPE:Since the first issue of a DLU the frame and rack hardware was redesigned several times in order to optimize the DLU HW concerning the required size and the number of connected subscriber lines.

DLU A :This is the oldest DLU HW type. It contains SLM modules with max. 8 subscriber circuits (e.g. SLMA : COS or SLMDB). It may also contains SLM modules with max. 6 home metering / reversal subscriber circuits (e.g. SLMA : CMRL. One fully equipped DLU A is housed in one rack R : DLU. A maximum of 952 analog or 928 digital subscribers with a traffic volume of 0.1 ERL each can be connected to a DLU A. One DLU A can consist of: y y 1 frame F:DLU (A) 0,1,2 or 3 frames F:DLU(B) depending on the number and the traffic volume of the subscribers

DLU B :This is the DLU HW type used in most EWSD switches. It contains SLM modules with max. 16 subscriber circuits (e.g. SLMA:FPE or SLMD:QFB). Two fully equipped DLUBs are housed in one rack R:DLUB. A maximum of 1760 analog or 1536 digital subscribers with a traffic volume of 0.1 ERL each can be connected to a rack R:DLUB. One DLU B can consist of: y y 1 frame F:DLU(D) 0 or 1 frame F:DLU(E) depending on the number and the traffic volume

of the subscribers (alternatively frame F:DLU(F) for less high construction )

DLU D ( also called DLU B type D) :This was the latest DLU HW type. The main difference to the DLUB is a new more integrated solution for the central parts of the DLU. This offers mounting locations for 4 additional SLMA:FPE modules to connect one remote DLU to EWSD. One DLU D can consist of : y y 1 frame F : DLU(G) 0 or 1 frame F:DLU(E) depending on the number and the traffic volume

of the subscribers (alternatively frame F:DLU(F) for less high construction)


10 | P a g e

6.2) LINE AND TRUNK GROUP:The line/trunk group (LTG) forms the interface between the digital environment of the node and the digital switching network (SN). The connection between the LTG and the duplicated switching network (SN) is made by a secondary digital carrier (SDC). The transmission rate on the SDC from the LTG to the SN and vice-versa is 8192 kbit/s (abbreviated to 8 Mbit/s). Each of these 8-Mbit/s multiplex systems has 127 time slots, each with 64 kbit/s for useful information, and one 64kbit/s time slot for messages. y Operation and maintenance functions The operation and maintenance functions of the LTG comprise: transmitting messages to the CP for traffic measurement and observation switching test calls testing the trunks and port-specific parts of the LTG with the aid of the integrated automatic test equipment for trunks (ATE:T) and the automatic test equipment for transmission measurement (ATE:TM) indication of important operating states (e.g. channel assignment) with respect to the functional equipment creation, blocking, release of equipment via man-machine language (MML) commands. y Subscriber connections are connections that convey useful information. The subscribers may be telephone subscribers, or also, for example, telecopying devices, fax machines. For setting up subscriber connections, each LTG has at its disposal 127 time slots (1 - 127), also called channels, per 8-Mbit/s multiplex system. y The User information is the for the communication relevante information (speech, text,data, picture). y Messages serve the purpose of inter-processor communication with the coordination

processor (CP), other LTGs and the CCNC. User information and messages are transmitted together. y Signaling is communication between network nodes.

11 | P a g e

Call processing functions:The call processing functions of the LTG comprise: receiving and interpreting the signaling from the trunk and subscriber line transmitting the signaling transmitting audible tones transmitting messages to the coordination processor (CP) and receiving commands from the CP transmitting and receiving reports from the group processors (GP) of other LTGs transmitting orders for common channel signaling network control (CCNC); receiving orders from the CCNC controlling the signaling to DLU, PA matching the line conditions to the 8-Mbit/s standard interface to the duplicated switching network (SN) through-connection of messages and useful information

6.3) SWITCHING NETWORK:The Digital Electronic Switching System (EWSD) is equipped with a very powerful switching network (SN). By virtue of its high data transmission quality, the switching network can switch connections for various types of service (for example telephony, facsimile, teletext, data transmission). This means that it is also ready for the IntegratedServices Digital Network (ISDN). The switching network, to which up to 504 line/trunk groups (LTG) can be connected (SN:504LTG), can be employed in a number of optimized capacity stages .

12 | P a g e

The most significant features of the switching network are: y y y y y y y y y y y y low space requirement negligible internal blocking high degree of functional integrity provided by duplication modular hardware and software only eight module types for all capacity stages of the switching network ease of expansion use of the latest technology (NMOS and TTLLS) one switching format for both speech and data signals (octets) single-channel connections broadcast connections (for application of signal sources) microprocessor control with read-only software (firmware) self-supervision multilayer printed circuit backplanes in the module frames

6.4) CO-ORDINATION PROCESSOR:A network node is divided into different function areas. The functions of these areas are implemented for the most part by independent subsystem. Each subsystem has its own microprocessor controls, for example, the group processors (GP) in the line/trunk groups (LTG) in the function area for access. The coordination processor (CP) is responsible for the common functions in the network node, such as the coordination of the distributed microprocessor controls and the data transfer between them.

The CP performs the following functions in a network node: Call processing Digit translation Routing Zoning Path selection through the switching network Call charge registration

13 | P a g e

Traffic data administration Network administration

Operation and maintenance Input and output from/to external memories (EM) Communication with the operation and maintenance terminal (OMT) Communication with the operation and maintenance center (OMC)

Safeguarding Self-supervision Fault detection Fault treatment

One CP type is available for all sizes and configurations of a network node, namely the 113D coordination processor (CP113D). The CP113D meets all the applicable safety and performance requirements.

Main features of the CP113D are: Use of a modular multiprocessor system can be adapted to different sizes of exchange Performance (dependent on configuration): typically, more than 1 000 000 BHCA (The effective, dynamic performance depends on the features available, the traffic distribution and the call mix; it must be defined individually for each case Combination of task and load sharing Redundancy achieved by duplication of important functional units as well as creation of call processor pools Use of high-performance micro-processor types processing width of 32 bits Addressing capacity of 4 Gbytes (for the CP113C) Common memory with a capacity of 64 Mbytes to 512 Mbytes (based on 4-Mbit DRAM)
14 | P a g e

Local memory per processor with a maximum capacity of 32 Mbytes (expansion up to the required capacity is affected by the use of an appropriate number of memory modules)

8 interrupt levels with fixed priorities Flexible in allowing connection of peripheral devices

6.5) CENTRAL CLOCK GENERATOR(CCG):In order to switch and transmit digital information, the sequence of operations must be synchronous throughout the equipment involved. This requires a clock supply with a high level of reliability, precision and consistency for all the nodes in the digital network.This task is fulfilled by the central clock generator (CCG), which is assigned to the coordination section of a node . In view of its vital role, the central clock generator is always duplicated. One is always switched as master and the other as slave. This ensures that in the event of a malfunction or failure affecting the master CCG, the master/slave roles can be switched over immediately and automatically, and that the clock supply to the connected subsystems continues uninterrupted. Each subsystem generates fresh synchronization pulses, which it synchronizes with the output pulses of the equipment unit preceding it in the circuit, in order to then synchronize the equipment unit following it in the circuit. In addition to internal clock distribution, there is also the option of external clock distribution, in which the CCG controls synchronization. This overview deals with the CCG and its functional units, clock distribution, and the prepositioned reference frequency hierarchy in networks.

6.6) SYSTEM PANEL(SYP):In the digital electronic switching system EWSD the system panel (SYP) belongs to the coordination processor 113 (CP 113). The purpose of the system panel is to display alarms and advisories of internal and external supervisory units (outside the system) both visually and acoustically. In contrast to the detailed error messages, which can be retrieved from the CP113 via the operation
15 | P a g e

and maintenance terminal (OMT) in the event of a malfunction, the system panel provides a continuous overview of the current functional status of the system. The functional status of exchanges in an entire areas can be monitored from a superordinate operation and maintenance center (OMC). For this purpose, a central system panel (CSYP), which displays all alarms and advisories reported by the exchanges, can be used in the OMC.

6.7) MESSAGE BUFFER(MB):A network node is subdivided into several functional areas. The tasks of these functional areas are performed by largely independent subsystems. The subsystem Message buffer B (MB(B)) is assigned to the coordination area of a network node.

The task of MB(B) is to control the exchange of messages between the following subsystems: coordination processor (CP113) and line/trunk groups (LTG): commands and messages CP113 and switch group controls (SGCB) of the switching network: setting commands for the switching network LTGs among one another: reports LTGs and the common channel signaling network control (CCNC): orders The MB(B) is designed for the more stringent performance requirements. The increased performance in conjunction with of an MBU:LTG Type C provides operation with an access network (AN) via interface V5.2 or TR303. The characteristics of an MB(B) with MBU:LTG Type C include the following: excellent reliability due to redundancy load distribution in normal operation control of broadcasting and collective commands higher transmission rate by rerouting reports within an MBUL(C) as well as the packeting or unpacketing of messages
16 | P a g e

microprocessor control with permanently stored software (firmware) self-monitoring simple expansion in stages . Structure of Message Buffer B:Depending on the capacity stage, MB(B) can accommodate up to four message buffer groups (MBG). It is implemented with redundancy in a network node, i.e. MB(B)0 comprises MBG00...MBG03, and MB(B)1 comprises MBG10...MBG13. The arrangement of MB(B) and MBGs in a network node, including redundancy is shown in fig. For reliability reasons, each MB(B) side (with its MBGs) is supplied via two IOP:MBs (transposition).

Arrangement of MB(B) in a network node

17 | P a g e

6.8) COMMON CHANNEL SIGNALLING NETWORK CONTROL(CCNC):The EWSD digital electronic switching system can control connections to and from other network nodes using all the common signaling systems. One system that is particularly suitable for stored-program-controlled digital nodes is signaling system no. 7 (SS7). This transports signaling information separately from the user information (voice, data) on common-channel signaling links.

The advantages of common channel signaling as against channel-associated signaling are: higher speed signaling large repertoire of signals very reliable signal transmission flexibility to adapt to future requirements SS7 common channel signaling can be used in all types of node: local and transit exchanges, international gateway exchanges and nodes serving mobile subscribers.

The following are suitable for the transmission medium: copper wires, optical fibers, digital radio links, satellite links.

The common-channel signaling links are conducted via an independent signaling network in which the nodes are integrated in the nodes of the telecommunication network or form independent nodes in the signaling network. There are two types of node in a signaling network, performing different functions: signaling points (SP), signaling transfer points (STP).

18 | P a g e

An SP represents the origin or destination of signaling messages. An STP receives signaling messages from an SP or another STP and forwards them to an SP or STP. Some signaling points may perform both SP and STP functions. The number of signaling points in a signaling network is determined by project or traffic requirements and conditions. The signaling functions in an EWSD network node are handled by the "common channel signaling network control (CCNC)". The CCNC handles the exchange of messages between different nodes in order to control and monitor connections and to administer the signaling network. The processors in the node pass messages they wish to transmit to the CCNC with the addresses of the relevant destination processors in the destination node. The CCNC now creates signaling messages in SS7 format from this information and sends them over the appropriate signaling links. When it receives incoming messages, the CCNC checks whether they are intended for a processor in its own node or whether they have to be forwarded over outgoing signaling links to another node. The separation of the traffic and signaling channels offers the advantage of being able to exchange any required signaling messages in parallel with the user information. Because the CP and CCNC are units which operate independently, no dynamic losses arise in the CP when there is signaling traffic.

7.0) COMMON CHANNEL SIGNALLING SYSTEM NO.7:Communication networks generally connect two subscriber terminating equipment units together via several line sections for message exchange (e.g. speech, data, text or images). Control information has to be transferred between the exchanges for call control and for the use of facilities. In analog communication networks, channel-associated signaling systems have so far been used to carry the control information. Fault free operation is guaranteed with the channel-associated signaling systems in analog communication networks, but the systems do not meet the requirements in digital, processor-controlled communication networks. Such networks offer a considerably larger scope of performance as compared with the analog communication networks, due, for instance, to a number of new services and facilities. The amount and variety of
19 | P a g e

the control information to be transferred is accordingly larger. The information can no longer be economically transported by the conventional channel-associated signaling systems. For this reason, a more efficient signaling system is required in digital, processor-controlled communication networks. The signaling system no. 7 (SS7) has therefore been specified. SS7 is optimized for application in digital networks.

It is characterized by the following main features: internationally standardized (national variations possible) suitable for the national and international/intercontinental network level suitable for various communication services such as telephony, text services, data services and other services suitable for service-specific communication networks and for the integrated services digital network (ISDN) high performance and flexibility along with a future-oriented concept which will meet new requirements high reliability for message transfer signaling on separate signaling links; the bit rate of the circuits is therefore exclusively for communication signaling links always available, even during existing calls use of the signaling links for transferring user data also used on various transmission medi cable (copper, optical fiber), radio relay, satellite (up to 2 satellite links) use of the transfer rate of 64 kbit/s typical in digital networks used also for lower bit rates and for analog signaling links if necessary automatic supervision and control of the signaling network (signaling links + signaling points).

20 | P a g e

8.0) EWSD:USE
Because of its inherent versatility, the EWSD system has become the universal switch, capable of responding to the full range of telecommunications standards and the full variety of global service demands. Over 160 million lines of EWSD switch capacity are now in service in more than 100 countries. In North America, EWSD systems are leading the introduction of integrated digital services, Advanced Intelligent Network (AIN) capabilities and open interfaces to multi-service terminal platforms. The Siemens EWSD Switching System is well ahead of the challenge with a uniquely flexible architecture that anticipates change and adapts easily. y Personal Communications Services:The EWSD switch offers Bellcore AIN 0.2 Personal Communications Services. In addition, the EWSD switch also provides Global System for Mobile communications (GSM) based PCS. Siemens has established itself as the world leader in GSM by its key role in European wireless communications and is building on that experience to link PCS and wired networks with the same fundamental EWSD technology. y Growing in Capacity and Connectivity:The EWSD Switching System is based on a modular hardware platform, completely integrated under generic software. Processing is distributed throughout the modular components, and the components can be assembled into a single central office, or they can be distributed to move call processing close to subscriber communities.

21 | P a g e

CONCLUSIONS

EWSD is a digital electronic switching system upgraded by Siemens, taking into account the latest tendencies of services and communication means development. It is the solution that makes it possible to satisfy any current and future requirements. The new applications implemented on the EWSD platform are the EWSD Inter Node and the EWSD Broadband Node. The EWSD Inter Node integrates Internet technology into the EWSD system, it creates the basic conditions required for speech and data networks to grow together. It offers unrestricted access to Internet services. The EWSD Broadband Node is the foundation stone for a future oriented network in which various types of technology, such as ISDN in the public network (PSTN) and broadband communication, harmoniously operate together. Broadband technology offers the network operator the opportunity to introduce completely new services, e.g. services with high-quality graphics and multimedia applications as well as video telephony. EWSD system is based on the most advanced technologies in the field of communication and provides the networks operators with the possibility of prompt and cost-effective response to the market needs. The growing need for the powerful networks is also conditioned by the subscriber traffic growth evoked primarily by new communication services implemented with the transfer rates of up to 2 Mbit/s. These services include ISDN, online services, Internet services, and the services implemented in n x 64 Kbit/s configuration.

22 | P a g e

APPENDIX

TECHNICAL DATA Call-handling capacity No. of Subscriber lines No. of Trunks Switchable traffic Call attempts in busy hour max. 250 000 max. 60 000 max. 25 200 E. 10 million

Supply voltage -48 V nominal direct voltage

Clock accuracy Maximum relative frequency deviation: plesiochoronous 10-9 synchronous 10-11

Signaling systems All conventional signaling systems, e.g. CCITT R2, No.5, No.7

Analog subscriber line and trunk accesses Various loop and shunt resistance possible. Push-button dialing, Multi-freq. signaling to CCITT Rotary dialing: 5 to 22 pulse/s
23 | P a g e

ISDN accesses Basic access 160 kbps(2B+D+sync.) B= 64 kbps, D= 16 kbps Primary rate access 2048 kbps(30B+D+sync.)

Digital trunk accesses

2048 kbps

Traffic routing Per destination one primary route and max. 15 alternate routes. Sequential or random selection of idle trunk of a trunk group Number of trunk groups per exchange: Max. 1000 incoming and Max. 1000 outgoing and Max. 1000 both way

Environmental conditions Ambient temperature Relative humidity 5C to 40C 10% to 80%

24 | P a g e

25 | P a g e

S-ar putea să vă placă și