Documente Academic
Documente Profesional
Documente Cultură
HUAWEI
The WCDMA system is a self interference system. As the load of the WCDMA system increases, the interference rises. A relatively high interference may affect the coverage and Quality of Service (QoS) of established services. Therefore, capacity, coverage and QoS of the WCDMA system are mutually affected. The purpose of load control is to maximize the system capacity while ensuring coverage and QoS.
() Objectives
Upon completion of this course, you will be able to: D Know load control principles a Know load control realization methods in WCDMA system D Know load control parameters in WCDMA system
Page2
HUAWEI
@ Contents
1. Load Control Overview 2. Load Control Algorithms
Page3
| H | HUAWEI
Contents
1. Load Control Overview 1.1 Load Control Alaorithms Overview 1.2 Load Measurement 1.3 Priorities Involved in Load Control
Page4
H l l HUAWEI
Load Definition
Load: the occupancy of capacity Two kinds of capacity in WCDMA system
Hard capacity . Cell DL OVSF Code vA I> '
NodeB processing capability (NodeB credit) n Soft capacity . Cell Power (UL and DL) ;
C^
Pages
H l l HUAWEI
WCDMA network load can be dened by 4 factors: 1. Power .include DL transmitting power of cell and increased UL interference (RTWP). 2. DL OVSF code of a cell 3. DL and UL NodeB processing capability which is dened by NodeB credit. 4. lub transmission bandwidth of a NodeB The power resource is related to the mobility, distribution of the UE and also effected by the radio conditions. Therefore, for a xed power resource, the numbers of service can be supported is not a x result. We believe the UL and DL power resources are soft.
Pagee
w l p HUAWEI
WCDMA network load can be defined by 4 factors: 1,Power .include DL transmitting power of cell and increased UL interference (RTWP). 2,DL OVSF code of a cell 3.DL and UL NodeB processing capability which is defined by NodeB credit. 4,lub transmission bandwidth of a NodeB The power resource is related to the mobility, distribution of the UE and also effected by the radio conditions. Therefore, for a fixed power resource, the numbers of service can be supported is not a fix result. We believe the UL and DL power resources are soft.
rrr
Time
1, Before UE access
"%>
*~ PUC: Potential User Control IAC: Intelligent Admission Control LDR: Load Reshuffling
CAC: Call Admission Control LDB : Intra-frequency Load Balancing OLC: Overload Control
Page?
i f | f HUAWEI
The load control algorithms are applied to the different UE access phases as follows: Before UE access: Potential User Control (PUC) During UE access: Intelligent Access Control (IAC) and Call Admission Control (CAC) After UE access: intra-frequency Load Balancing (LDB), Load Reshuffling (LDR), and Overload Control (OLC)
i i
NodeB
RNC
CN
t I
Iub
Iu
PageS
HUAWEI
The load control algorithms are built into the RNC. The input of load control comes from the RNC and measurement information of the NodeB. RNC can calculate hard resource load, that is OVSF ,NodeB credit, Iub occupancy. The soft load need the NodeB reporting.
Contents
1 . Load Control Overview 1.1 Load Control Algorithms Overview 1.2 Load Measurement 13 Priorities Involved in Load Control
Page9
Wf
HUAWEI
JU
> ,*&&
*j
iAr^
*L
PagelO
W W
HUAWEI
The soft load control algorithms use load measurement values in the uplink and the downlink. A common Load Measurement (LDM) algorithm is required to control load measurement in the uplink and the downlink. The NodeB and the RNC perform measurements and filtering in accordance with the parameter settings. The statistics obtained after the measurements and filtering serve as the data input for the load control algorithms. The major measurement objects of the LDM are as follows: Uplink Received Total Wideband Power (RTWP) Received scheduled Enhanced Dedicated Channel (E-DCH) power share (RSEPS) E-DCH Provided Bit Rate oDownlink Transmitted Carrier Power (TCP) TCP of all codes not used for High Speed Physical Downlink Shared Channel (HSPDSCH), High Speed Shared Control Channel , (Non-HSPA TCP) Provided Bit Rate on HS-DSCH (PBR) HS-DSCH required power, also called Guaranteed Bit Rate (GBR) required power (GBP)
I
Sam;:: L1/L3 filtering
State and load information processing State and load information processing Slate and load information processing
-*! -*-
tt
Stale and toad -+information processing State and toad information processing
IX, p() = i = 2 _
N
HUAWEI
The NodeB measures the major measurement quantities and then obtains original measurement values. After layer 3 filtering on the NodeB side, the NodeB reports the cell measurement values to the RNC. The RNC performs smooth filtering on the measurement values reported from the NodeB and then obtains the measurement values, which further serve as data input for the load control algorithms. Filtering on the NodeB Side
Parameters
+
A Layer 1 filtering 8 Layer 3 filtering
I I
I I
A is the sampling value of the measurement. B is the measurement value after layer 1 filtering. C is the measurement value after layer 3 filtering ,which is the reported measurement value Layer 1 filtering is not standardized by protocols and it depends on vendor equipment. Layer 3 filtering is standardized. The filtering effect is controlled by a higher layer.
The NodeB periodically reports each measurement quantity to the RNC. The following table lists the reporting intervals for the measurement quantities.
Measurement RTWP RSEPS TCP Non-HSDPA power GBP HS-DSCH PBR E-DCH PBR
Smooth Window Filtering on the RNC Side
Reporting Interval ( Unit: ms ) 1000 1000 200 200 1000 100 100
After the RNC receives the measurement report, it filters the measurement value with the smooth window. Assuming that the reported measurement value is Qn and that the size of the smooth window is N, the filtered measurement value is :
W-l
Q =^ ^ , N
Delay susceptibilities of PUC, CAC, LDR, and OLC to common measurement are different. The LDM algorithm must apply different smooth filter coefficients and measurement periods to those algorithms; thus, they can get expected filtered values.
default Value 32 32 25 3 25
Smooth window for GBP for all related algorithms are the same and the default setting is 1
Contents
1 . Load Control Overview 1.1 Load Control Algorithms Overview 1.2 Load Measurement 1.3 Priorities Involved in Load Control
Pagel 3
W w
HUAWEI
13
Priority
The service of user with low priority wi 1 be affectedby the load control algorithms first
Three kinds of priorities a User Priority D RAB Integrate Priority n User Integrate Priority
Page14
##
HUAWEI
User Priority: mainly applying to provide different QoS for different users. Eg., setting different GBR according to the user priority for BE service. No consideration about the service. RAB Integrate Priority: Priority of a service, related to the service type, and the user priority of the user. User Integrate Priority: Only used for multi-RAB user ,it is a temporary priority of an ongoing-service user.
User Priority
There are three levels of user priority ^1 a gold (high), silver (middle) and copper (low) user
C~^)
Page15
#i
HUAWEI
In CN HLR, we can set ARP (Allocation Retention Priority ).During service setup, CN sends ARP to RNC .Based on the mapping relation( configured in RNC), RNC can identify the user's priority, gold, silver or copper one. The user priority affect GBR of a BE service in RAN, Iub transmission management and so on. B ^ allocationOrRetentioriPriority priorityLeveLOxc (12) pre-emptionCapability:shall-not-trigger-pre-emption (0) pre-emptionVulnerability:not-pre-emptable (0) queuingAllowediqueueing-allowed (1)
User Priority
# The mapping relation between user priority and ARP . (Allocation/Retention Priority) is configured in RNC by SET USERPRIORITY n An example:
ARP
10
11
12
13
14
15
User Priority
Gold
Silver
Copper
Page16
<Pj H U A W E I
The user priority mapping can be configured in RNC by SET USERPRIORITY ARP 15 is always the lowest priority and it cannot be configured. It corresponds to copper. If ARP is not received in messages from the Iu interface, the user priority is regarded as copper.
Page17
0$ HUAWEI
RAB Integrate Priority is mainly used in load control algorithms. The values of RAB Integrate Priority are set according to the Integrate Priority Configured Reference parameter as follows: If Integrate Priority Configured Reference is set to Traffic Class, the integrate priority abides by the following rules: Traffic classes: conversational -> streaming -> interactive -> background => Services of the same class: Priority based on Allocation/Retention Priority (ARP) values, that is, ARP1 -> ARP2 -> ARP3 -> ... -> ARP14 => Only for the interactive service of the same ARP value: priority based on Traffic Handling Priority (THP, defined in CN , sent to RNC during service setup), that is, THP1 -> THP2 -> THP3 -> ... -> THP14 => Services of the same ARP, class and THP (only for interactive services): High Speed Packet Access (HSPA) or Dedicated Channel (DCH) service preferred depending on the value of the Indicator of Carrier Type Priority parameter.
If Integrate Priority Configured Reference is set to ARP, the integrate priority abides by the following rules: ARP1 -> ARP2 -> ARP3 -> ... -> ARP14 => Traffic classes: conversational -> streaming -> interactive -> background => Only for the interactive service of the same ARP value: priority based on Traffic Handling Priority (THP), that is, THP1 -> THP2 -> THP3 -> ... -> THP14 => Services of the same ARP, class and THP (only for interactive services): HSPA or DCH service preferred depending on the value of the Indicator of Carrier Type Priority parameter. Integrate Priority Configured Reference and Indicator of Carrier Type Priority are set by SET USERPRIORITY . By default Integrate Priority Configured Reference is set to ARP Indicator of Carrier Type Priority is set to NONE, that means HSPA and DCH services have the same priority. ARP and THP are carried in the RAB ASSIGNMENT REQUEST message, and they are not configurable on the RNC LMT.
An Example for RAB Integrate Priority Based on ARP, HSPA priority is higher
Service ARP ID Services attribution in the cell Service ARP ID A B C D 1 1 2 2 Traffic Class Interactive Interactive Conversational Background Bear type DCH HSDPA DCH DCH B A C D 1 1 2 2 Traffic Class Interactive Interactive Conversational Background Bear type HSDPA DCH DCH DCH
Based on Traffic Class, HSPA priority is higher Service ID C B A D Traffic Class Conversational Interactive Interactive Background
Page19
ARP 2 1 1 2
This example shows the RAB Integrate Priority calculation in 2 different conditions
Page20
<|N HUAWEI
When the user has one RAB, User integrate priority is the same as the service of the RAB integrate priority; For multiple RAB users, the integrate priority of the user is based on the service of the highest priority. User integrate priority is used in user-specific load control. For example, the selection of R99 users during preemption, the selection of users during inter-frequency load handover for LDR, and the selection of users during switching BE services to CCH are performed according to the user integrate priority.
Page21
| 1 # HUAWEI
Integrate Priority Configured Reference Parameter ID: PRIORITYREFERENCE Value range: ARP, Traffic Class Content: This parameter is used to set the criterion by which the priority is first sorted. The default value of this parameter is ARP Set this parameter through SET USERPRIORITY Indicator of Carrier Type Priority Parameter ID: CARRIERTYPEPRIORIND Value range: NONE, DCH, HSPA Content: This parameter is used to decide which carrier (DCH or HSPA) takes precedence when ARP and Traffic Class are identical. When this parameter is set to NONE, the bearing priority of services on the DCH is the same as that of HSPA services. The default value of this parameter is NONE, Set this parameter through SET USERPRIORITY
^ J Contents
2. Load Control Algorithms 2.1 PUC (Potential User Control) 2.2 LDB (Intra-Frequency Load Balancing) 2.3 CAC {Call Admission Control) 2.4 IAC (Intelligent Admission Control) 2.5 LDR (Load Reshuffling) 2.6 OLC (Overload Control)
Page22
j l |
HUAWEI
PUC Principles
* The Potential User Control (PUC) algorithm controls the inter-.J ir
s**
.frequency cell reselection of the potential UE, and prevents UE from camping on a heavily loaded cell. Potential UE : D IDLE Mode UE Q CELL-FACH UE, CELL-PCH UE, URA-PCH UE
Page23
If
HUAWEI
The function of PUC is to balance traffic load among inter-frequency cells. By modifying cell selection and reselection parameters and broadcasting them through system information, PUC leads UEs to cell with light load. The UE may be in idle mode, Cell_FACH state, Cell _PCH state, UfRA_PCH state
i
Heavy Normal
ISI on
t t t t
time
HUAWEI
Cell load for PUC is of three states: heavy, normal, and light The RNC periodically monitors the downlink load of the cell and compares the measurement results with the configured thresholds Load level division threshold 1 and Load level division threshold 2, that is, load level division upper and lower thresholds. If the cell load is higher than the ioad level division upper threshold plus the Load level division hysteresis, the cell load is considered heavy. If the cell load is lower than the load level division lower threshold minus the Load level division hysteresis, the cell load is considered light. Otherwise the cell load is considered normal
5^'\
c\
Sy\
v-v*
->T
PUC Procedure
Threshold Every 200ms
Cell TCP
Every 30 minutes
Page25
HUAWEI
The parameters related to cell selection and cell reselection are Qoffset1(s,n) (load level offset), Qoffset2(s,n) (load level offset), and Sintersearch (start threshold for interfrequency cell reselection). The NodeB periodically reports the total TCP of the cell, and the PUC periodically triggers the following activities: Assessing the cell load level based on the total TCP Configuring Sintersearch, Qoffset1(s,n), and Qoffset2(s,n) based on the cell load level PUC can Modify inter-frequency cell reselection parameters based on the load: 1 s
**intersearch
when the load of a cell is "Heavy", PUC will increase Sintersearch when the load of a cell is "Light", PUC will decrease Sjntersearch
2- Qoffset1
when the load of current cell is "Heavy" and neighbor is "Non heavy", PUC will decrease
^Offset 5ffset
when the load of current cell is "Non heavy" and neighbor is "Heavy", PUC will increase
^Offset
Sintersearch S'intersearch = Sintersearch + Sintersearch offset 1 S'intersearch = Sintersearch S'intersearch = Sintersearch + Sintersearch offset 2 \ /
Change of Sintersearch
: indicates that the parameter value remains unchanged. / : indicates that the parameter value increases. \ : indicates that the parameter value decreases.
Q'offsetl
Change of Q'offsetl
Qoffset2
Change of Q'offse
i
Non-Heavy Non-Heavy
NonHeavy Heavy
Q'offsetl = Qoffsetl Q'offsetl = Qoffsetl + Qoffsetl offset 1 Q'offsetl = Qoffsetl + Qoffsetl offset 2 Q'offsetl = Qoffsetl
Q'offsetZ = Qoffset2 Qoffset2 = Qoffset2 + Qoffset2 offset 1 Q'offset2 = Qoffset2 + Qoffset2 offset 2 Q'offset2 = Qoffset2 \
Heavy
NonHeavy Heavy
Heavy
-*
-*
PUC Principles
Freql System Inf SIB3.11 LHard to trigger reselection 2.Easy to camp on the cell Increase the POTENTIAL load System Int SIB3.11
Freq2 1. Easy to trigger reselection 2.Easy to select light load Inter-freq neighbor Cell
,-^ J^
Heavy load
18'
CCH state
Page27
HUAWEI
Based on the characteristics of inter-frequency cell selection and reselection. Sintersearch When this value is increased by the serving cell, the UE starts inter-frequency cell reselection ahead of schedule. When this value is decreased by the serving cell, the UE delays inter-frequency cell reselection. Qoffsetl (s,n): applies to R (reselection) rule with CPICH RSCP When this value is increased by the serving cell, the UE has a lower probability of selecting a neighboring cell. When this value is decreased by the serving cell, the UE has a higher probability of selecting a neighboring cell. Qoffset2(s,n): applies to R (reselection) rule with CPICH Ec/10 When this value is increased by the serving cell, the UE has a lower probability of selecting a neighboring cell. When this value is decreased by the serving cell, the UE has a higher probability of selecting a neighboring cell.
Page28
H # HUAWEI
Cell LDC algorithm switch Parameter ID: NBMLDCALGOSWITCH PUC Value range: OFF, ON Content: This parameter is used to enable or disable the PUC algorithm.. The default value of this parameter is OFF Set this parameter through ADD CELLALGOSWITCH /MOD CELLALGOSWITCH
Load level division threshold 1 (Heavy) Parameter ID: SPUCHEAVY Value range: 0 to 100 Content: This parameter is one of the thresholds used to assess cell load level and to decide whether the cell load level is heavy or not. The default value of this parameter is 70%, Set this parameter through ADD CELLPUC / MOD CELLPUC Load level division threshold 2 (Light) Parameter ID: SPUCLIGHT Value range: 0 to 100 Content: This parameter is one of the thresholds used to assess cell load level and to decide whether the cell load level is heavy or not. The default value of this parameter is 45%, Set this parameter through ADD CELLPUC / MOD CELLPUC
Page30
4jp|t HUAWEI
Load level division hysteresis Parameter ID: SPUCHYST Value range: OFF, ON Content: This parameter specifies the hysteresis used during cell load level assessment to avoid unnecessary ping-pong effect of a cell between two load levels due to a little load change. The default value of this parameter is 5 (5%) Set this parameter through ADD CELLPUC / MOD CELLPUC PUC period timer length Parameter ID: PUCPERIODTIMERLEN Value range: 6 to 86400 s Content: This parameter specifies the period of potential user control. The higher the parameter is set, the longer the period to trigger the PUC is. The default value of this parameter is 1800(s) Set this parameter through SET LDCPERIOD
Page31
4 H | HUAWEI
Sintersearch offset 1 Parameter ID: OFFSINTERLIGHT Value range: -10 to 10 ,step:2dB Content: This parameter defines the offset of Sintersearch when the center cell load level is "Light". It is strongly recommended that this parameter be set to a value not higher than 0. The default value of this parameter is -2 (-4dB) Set this parameter through ADD CELLPUC / MOP CELLPUC Sintersearch offset 2 Parameter ID: OFFSINTERHEAVY Value range: -10 to 10 ,step:2dB Content: This parameter defines the offset of Sintersearch when the center cell load level is "Heavy". It is strongly recommended that this parameter be set to a value not lower than 0. The default value of this parameter is 2 (4dB) Set this parameter through ADD CELLPUC / MOD CELLPUC
a Parameter ID: OFFQOFFSET1 HEAVY o The default value of this parameter is 4 (8dB)
Page32
| H | HUAWEI
Qoffsetl offset 1 Parameter ID: OFFQOFFSET1 LIGHT Value range: - 1 0 to 10 ,step:2dB Content: This parameter defines the offset of Qoffsetl (RSCP) when the current cell has heavy load and the neighboring cell has light or normal load. To enable the UE to select a neighboring cell with relatively light load, it is strongly recommended that this parameter be set to a value not higher than 0. The default value of this parameter is -4 (-8dB) Set this parameter through ADD CELLPUC/MOD CELLPUC Qoffsetl offset 2 Parameter ID: OFFQOFFSET1 HEAVY Value range: - 1 0 to 10 ,step:2dB Content: This parameter defines the offset of Qoffsetl (RSCP) when the load of a neighboring cell is heavier than that of the center cell. To enable the UE to select a neighboring cell with relatively light load, it is strongly recommended that this parameter be set to a value not lower than 0. The default value of this parameter is 4 (8dB) Set this parameter through ADD CELLPUC/MOD CELLPUC
Page33
H # HUAWEI
Qoffsetl offset 1 Parameter ID: OFFQOFFSET1 LIGHT Value range: -10 to 10 ,step:2dB Content: This parameter defines the offset of Qoffsetl (RSCP) when the current cell has heavy load and the neighboring cell has light or normal load. To enable the UE to select a neighboring cell with relatively light load, it is strongly recommended that this parameter be set to a value not higher than 0. The default value of this parameter is -4 (-8dB) Set this parameter through ADD CELLPUC/MOD CELLPUC Qoffsetl offset 2 Parameter ID: OFFQOFFSET2HEAVY Value range: -10 to 10 ,step:2dB Content: This parameter defines the offset of Qoffset2 (EcNo) when the load of a neighboring cell is heavier than that of the center cell. To enable the UE to select a neighboring cell with relatively light load, it is strongly recommended that this parameter be set to a value not lower than 0. The default value of this parameter is 4 (8dB) Set this parameter through ADD CELLPUC / MOD CELLPUC
Contents
2. Load Control Algorithms 2.1 PUC (Potential User Control) 2.2 LDB (Intra-Frequency Load Balancing) 2 3 CAC (Call Admission Control) 2.4 IAC (Intelligent Admission Control) 2.5 LDR (Load Reshuffling) 2.6 OLC (Overload Control)
!: :,:-
Copyright 2009 Huawei Technologies Co., Ltd. Ail rights reserved. >
Page3S
||U|| HUAWEI
Intra-frequency Load Balancing (LDB) is performed to adjust the coverage areas of cells according to the measured values of cell downlink power load. RNC checks the load of cells periodically and adjusts the transmit power of the P-CPICH in the associated cells based on the cell load. When the load of a cell increases, the cell reduces its coverage to lighten its load. When the load of a cell decreases, the cell extends its coverage so that some traffic is off-loaded from its neighboring cells to it. Reduction of the pilot power will make the UEs at the edge of the cell handed over to neighboring cells, especially to those with a relatively light load and with relatively high pilot power. After that, the downlink load of the cell is lightened accordingly.
LDB Procedure
Threshold
^^ Normal?
!
RNC
NodeB
UE
Page36
^%
HUAWEI
The NodeB periodically reports the total TCP of the cell, and the LDB periodically triggers the following activities: Assessing the cell load level based on the total TCP If the downlink load of a cell is higher than the value of the Cell overload threshold, it is an indication that the cell is heavily loaded. In this case, the transmit power of the PCPICH needs to be reduced by a step, which is defined by the Pilot power adjustment step parameter. However, if the current transmit power is equal to the value of the Min transmit power of PCPICH parameter, no adjustment is performed. If the downlink load of a cell is lower than the value of the Cell underload threshold, it is an indication that the cell has sufficient remaining capacity for more load. In this case, the transmit power of the P-CPICH increases by a step, which is defined by the Pilot power adjustment step parameter, to help to lighten the load of neighboring cells. However, if the current transmit power is equal to the value of the Max transmit power of PCPICH parameter, no adjustment is performed.
n Parameter ID: IntraFreqLdbPeriodTimerLen p The default value of this parameter is 1800 (s)
Page37
| | i HUAWEI
Cell LDC algorithm switch Parameter ID: NBMLdcAlgoSwitch LDB Value range: OFF, ON Content: This parameter is used to enable or disable the LDB algorithm.. The default value of this parameter is OFF Set this parameter through ADD CELLALGOSWITCH / MOD CELLALGOSWITCH intra-frequency LDB period timer length Parameter ID: IntraFreqLdbPeriodTimerLen Value range: 0 to 86400 Content: This parameter specifies the length of the intra-frequency LDB period. The default value of this parameter is 1800 (s) Set this parameter through SET LPCPERIOD
a Parameter ID: CellUnderrunThd The default value of this parameter is 30(30%) Pilo t power adjustmen t s tep a Parameter ID: PCPICHPowerPace n The default value of this parameter is 2 (0.2dB)
MHP
Copyright 2009 Huawei Technologies Co., Ltd. All rights reserved. Page38
$ % HUAWEI
Cell overload threshold Parameter ID: CellOverrunThd Value range: 0 to 100 Content: If the downlink load of a cell exceeds this threshold, the algorithm can decrease the pilot transmit power of the cell so as to extend the capacity of the whole system. The default value of this parameter is 90%, Set this parameter through ADD CELLLDB / MOO CELLLDB
Cell underload threshold Parameter ID: CellUnderrunThd Value range: 0 to 100 Content: If the downlink load of a cell is lower than this threshold, the algorithm can increase the pilot transmit power of the cell so as to share the load of other cells. The default value of this parameter is 30%, Set this parameter through ADD CELLLDB / MOD CELLLDB Pilot power adjustment step Parameter ID: PCPICHPowerPace Value range: 0 to 10 , Step 0.1 dB Content: This parameter defines the step for the adjustment to the pilot power. The default value of this parameter is 2, 0.2dB Set this parameter through ADD CELLLDB / MOD CELLLDB
Page39
| P i | HUAWEI
Max transmit power of PCPICH Parameter ID: MaxPCPICHPower Value range: -100 to 500 .Step 0.1 dB Content: This parameter defines the maximum transmit power of the P-CPICH in a cell. This parameter has to be set according to the actual system environment, that is, for example, cell coverage (radius) and geographical environment. If the maximum transmit power of the P-CPICH is set too low, the cell coverage decreases. When a certain proportion of soft handover area is ensured, any more increase in the pilot power achieves no improvement on the performance of the downlink coverage. The default value of this parameter is 346 (34.6dBm) Set this parameter through ADD PCPICH / MOP PCPICHPWR Min transmit power of PCPICH Parameter ID: MinPCPICHPower Value range: -100 to 500 Content: This parameter defines the minimum transmit power of the P-CPICH in a cell. This parameter has to be set according to the actual system environment, that is, for example, (radius) and geographical environment. If the minimum transmit power of the P-CPICH is set too low, the cell coverage will be affected. The parameter has to be set under the condition that a certain proportion of soft handover area is ensured or the occurrence of coverage hole can be prevented. The default value of this parameter is 313 (31.3dBm) Set this parameter through ADD PCPICH / MOD PCPICHPWR
@ Contents
2. Load Control Algorithms 2.1 PUC (Potential User Control) 2.2 LDB (Intra-Frequency Load Balancing) 2.3 CAC (Call Admission Control) 2.4 IAC (Intelligent Admission Control) 2.5 LDR (Load Reshuffling) 2.6 OLC (Overload Control)
Page40
4fH HUAWEI
Page41
| H | HUAWEI
CAC is needed under such scenarios: 1. RRC connection setup request 2. RAB setup and Bandwidth increasing 3. Handover 4. Rate reconfiguration (Reconfigure RB)
res
Code Yes l-'ower aiJiTH'-.-.iiji'r--' Ye-, NodeB credit admission? admissionv
iub r e s o u r c e a d m i s s i o n ?
HUAWEI
The admission decision is based on: Cell available code resource: managed in RNC Cell available power resource, that is DL/UL load : measured in NodeB NodeB credits, that is, NodeB processing resource state, Channel Elements .managed in RNC Available Iub transport layer resource, that is, Iub transmission bandwidth: managed in RNC HSPA user number (only for HSPA service)
Page43
| l HUAWEI
Except the mandatory code and Iub resource admission control, the admission control based on power and NodeB credit,HSDPA User Number can be disabled through the LMT command: Power CAC can be switched off by ADD CELLALGOSWITCH / MOD CELLALGOSWITCH Uplink CAC algorithm switch (NBMULCACALGOSELSWITCH ) specifies the algorithm used for power admission in the uplink. Downlink CAC algorithm switch (NBMDLCACALGOSELSWITCH) specifies the algorithm used for power admission in the downlink. NodeB Credit CAC can be switched off bv SET CACALGOSWITCH CELLALGOSWITCH / MOD CELLALGOSWITCH or ADD
CAC algorithm switch (CacSwitch) specifies the NodeB level credit CAC algorithm Cell CAC algorithm switch (CRD_ADCTRL) specifies the Cell level credit CAC algorithm. HSDPA user number CAC switched off by ADD CELLALGOSWITCH / MOD CELLALGOSWITCH HSDPA_UU_ADCTRL specifies whether to enable or disable the HSDPA admission control algorithm. HSUPA user number CAC switched off by ADD CELLALGOSWITCH / MOD CELLALGOSWITCH HSUPA_UU_ADCTRL specifies whether to enable or disable the HSUPA admission control algorithm
Page44
| # HUAWEI
When a new service attempts to access the network, code resource admission is mandatory. 1. For RRC connection setup requests, the code resource admission is successful if the current remaining code resource is enough for the RRC connection. 2. For handover services, the code resource admission is successful if the current remaining code resource is enough for the service. 3. For R99 services setup and Rate Reconfiguration, the RNC has to ensure that the remaining code does not exceed the configurable threshold after admission. 4. For HSDPA services, the reserved codes are shared by all HSDPA services. Therefore, the code resource admission is not needed. So the RRC connection setup and Handover has higher priority to access a cell
Page45
# # HUAWEI
The UL CAC and DL CAC are independent. The basic principle of Power CAC is: RNC predict the cell power load after the access. If the load will be higher than a threshold, the admission is failed. So, by setting different threshold for different access services, we can realize different priorities. Power admission is used in all the access scenarios, except for: For Intra-frequency handover request, uplink power admission is not need. For rate downsizing, RNC accept the request directly without admission.
Algorithm 2: based on Equivalent Number of User (ENU) Algorithm 3: loose call admission control algorithm
/>y*V
Page46
flHI
HUAWEI
Huawei provide 3 Power CAC Algorithms Algorithm 1: power resource admission decision based on power or interference. Depending on the current cell load (uplink load factor and downlink transmitted carrier power) and the access request, the RNC determines whether the cell load will exceed the threshold upon admitting a new call. If yes, the RNC rejects the request. If not, the RNC accepts the request. Algorithm 2: power resource admission decision based on the number of equivalent users.Based on Huawei testing and experience, The 12.2 kbit/s AMR traffic is used to calculate the Equivalent Number of Users (ENU) of all other services in UL and DL. The 12.2 kbit/s AMR traffic's ENU is assumed to be 1. Depending on the current number of equivalent users and the access request in UL and DL, the RNC determines whether the number of equivalent users will exceed the threshold upon admitting a new call. If yes, the RNC rejects the request. If not, the RNC accepts the request. Algorithm 3: power resource admission decision based on power or interference, but with the estimated load increment always set to O.Depending on the current cell load (uplink load factor and downlink TCP) and the access request, the RNC determines whether the cell load will exceed the threshold, with the estimated load increment set to 0. If yes, the RNC rejects the request. If not, the RNC accepts the request.
n fc
iT T
(LV*I X
Get current RTWP, and calculate the current load factor Get the traffic characteristic, and estimate the increment of load factor
-%t=l-
RTWP
X
Calculate the predicted load factor "^VL predicted ~ VuL + A /7 + T]CCH
End of UL CAC
Page47
f t
' '
HUAWEI
Pn is uplink receive background noise. The procedure for uplink power resource decision is as follows: 1. 2. 3. 4.
JAXMTHT
The RNC obtains the uplink RTWP of the cell, and calculate the current uplink load factor. The RNC calculates the uplink load increment A n. UL based on the service request. The RNC uses the formula n UL,predicted= n UL + A n UL to forecast the uplink load factor. By comparing the forecasted uplink load factor a UL.predicted with the corresponding threshold ,the RNC decides whether to accept the access request or not.
For HSUPA service access, the RSEPS and PBR will be considered when calculating the cell load.
^:
j^
Ji
*AA
A
K^ -y
A>
if
Get measurement TCP and calculate the current downlink load factor
V
TCP
<
-+
^=ir
lot,?**** -Vm*^Hm +%!_**
v
Get the predicted downlink factor
Page48
HUAWG1
The procedure for downlink power resource decision is as follows: 1. The RNC obtains the cell downlink TCP and calculates the downlink load factor i j DL by dividing the maximum downlink transmit power Pmax by this TCP. 2. The RNC calculates the downlink load increment A P based on the service request and the current load. 3. The RNC forecasts the downlink load factor. 4. By comparing the downlink load factor with the corresponding threshold (DL threshold of Conv AMR service, DL threshold of Conv non_AMR service, DL threshold of other services, DL Handover access threshold), the RNC decides whether to accept the access request or not. For HSDPA service access, the GBP and PBR should be considered.
i
Get current total ENU
E N U t M l ( N ) = Y.ENU,
>v,
I
Get the traffic characteristic, and estimate the increment of ENU
^ *N.
new
it
1
Calculate the predicted ENU
\
admitted
ENULoad =
ENUtotal(N+l)/ENUaax
''
rejected
o
Page49 ^ ^ HUAWEI
Cop> right 2009 Huawei Technolog es Co., Ltd. All rights re served.
The procedure for ENU resource decision is as follows: 1. The RNC obtains the total ENU of all exist users ENUtotal. 2. The RNC get the ENU of the new incoming user ENUnew. 3. The RNC forecast the ENU load. 4. By comparing the forecasted ENU load with the corresponding threshold (the same threshold as power resource), the RNC decides whether to accept the access request or not. The ENUmax can be set by LMT, the ENUnew and ENUi is determined by Huawei algorithm, there is an example in next slide.
PageSO
w w
HUAWEI
To ensure that the RRC connection request is not denied by mistake, tolerance principles are applied. The admission decision is made for the following reasons of the RRC connection request: 1. For the RRC connection request for the reasons of emergency call, detach or registration, direct admission is used ,that is no limitation. 2. For the RRC connection request for other reasons, UL/DL OLC Trigger threshold is used for admission. By default, the OLC trigger threshold is relatively high (DL/UL 95%), which make the RRC connections are easily set up.
+r
luL-CCH
Where the
VuL
RTWP
By comparing the predicted uplink load factor n ULiPredicted with the corresponding threshold ,the RNC decides whether to accept the access request or not
Page51
wPIB' H U A W E I
The threshold for Conv AMR service , Conv non_AMR service , Other R99 services Handover are set independently, which provide different priorities. Normally, Other R99 services < Conv non_AMR service services < Conv AMR service < Handover The uplink load increment A n UL is determined by: 1. The Eb/No of the new incoming call 2. The uplink load increment is proportional to the value of Eb/No. 3. UL neighbor interference factor 4. Active Factor of the new incoming call
^DL
^DL-CCH
a Where the
?
TCP
7z>i=TT-
.
^DL-
_A?70i
By comparing the predicted downlink load factor ri DLiPredicted with the corresponding threshold ,the RNC decides whether to accept the access request or not
PageS2
W W
HUAWEI
The threshold for Conv AMR service , Conv non_AMR service , Other R99 services , Handover are set independently, which provide different priorities. Normally, Other R99 services < Conv non_AMR service services < Conv AMR service < Handover The downlink load increment A n DL is determined by: 1. The Eb/No of the new incoming call 2. Non-orthogonality factor 3. Current transmission carrier power 4. Active Factor of the new incoming call
Controllable part
The UL interference generated by E-DCH scheduling services belong to the controllable part
Uncontrollable part
Pge53
HUAWEI
RSEPS
T
EDCH Scfteduted
(TyJKJ A)
f 1 1
I *******
t
r
*
RTWP
JL_,
F
Jfci,
luL,EDCH
Page54
H H HUAWEI
^'HuL
+
tfuL^ch
+
W HS-DPCCH
<
<
^thd
tfuL.^ch
tfHS-DPCCH
tfthd-total
PageSS
|f) HUAWEI
n thd_tota| is the UL total power threshold of the current cell n thd is the cell UL admission threshold for specific type of service, that is UL threshold of Conv AMR service, UL threshold of Conv non_AMR service, UL threshold of other services or UL handover access service threshold
v
+ +
GS/C,
"'' QtM-Mel.' ' ^ z w g cases H'HS-DPCCH
-^ %i
+
'fol.cch
V HS-DPCCH
5. ^VL.mtt-ctrl n
^Rt + lui.uh
RNC admits HSUPA Non-scheduling service in either of the following cases a a Formula 1,2 or 3 is fulfilled Formula 4 and 5 are fulfilled
Page56
HUAWEI
ThdL is the Low priority HSUPA user PBR threshold of the current cell ThdE is the Equal priority HSUPA user PBR threshold of the current cell ThdGE is the High priority HSUPA user PBR threshold of the current cell
SPI lew user PE R, P 3R2
t
PBR,
Sflr-^-f,,,
PBR, >TM
- ]T
13
c,Hli
; )
i
10
11
12
14
15
P 8k >Th**..'
I <;HH,
eR
n HS.DPCCH ' s ^ e v a l u e f the UL HS-DPCCH reserve factor parameter, which defines the factor of UL HS-DPCCH resource reserved n tnd is the cell UL admission threshold for specific type of service, that is UL threshold of Conv AMR service, UL threshold of Conv non_AMR service, UL threshold of other services or UL handover access service threshold
PaqfiS?
MRS' HUAWEI
x. p
' fc_re
4. \P
< P
. ThA
um ' ""-.*v>>H~t;itv
' xm-htpa
'-" 111. ~
*hmpa_*!>**nm.
h^J
^"lX. -
"mix '
*'K't,/ijl-iar,
RNC admits R99 service (i.e. DCH RAB) in either of the following situations: Formula 1 and 2 are fulfilled Formula 1 and 3 are fulfilled
: ::;:;:: :: ' : '" " :: ::: :. Copyright 2009 Huawei Technologies Co., Ltd. All rights reserved.
Page58
flp
HUAWEI
Pnon_hspa is the current non-HSDPA power Pcch.res is the power reserved for the common channel Pmax is the cell maximum transmit power Thd^n^spg^g,. is the cell DL admission threshold for different types of service, that is DL threshold for Conv AMR service, DL threshold for Conv non-AMR service, DL threshold for other service or DL handover access threshold Ptotal is the current downlink transmitted carrier power Thdtotal-cac is the threshold of cell DL total power. It is defined by the DL total power threshold parameter GBP is power requirement for GBR nsupa-resis t h e Pwer reserved for HSUPA downlink control channels (E-AGCH/E-RGCH/E-HICH) F'max-nspa is the maximum available power for HSPA. Its value is associated with the HSDPA power allocation mode.
p
PBR^lzThd,^.
1
_ YCBRa, ,
, GBP + PU
+AP, <P
RNC admits the HSDPA streaming service in any of the following situations: a Formula 1 is fulfilled Formulas 3 and 4 are fulfilled Formulas 3 and 5 are fulfilled
RNC admits the HSDPA BE service in any o f the following situations: a a a Formula 2 is fulfilled Formulas 3 and 4 are fulfilled Formulas 3 and 5 are fulfilled
Page59
3# H U A W E I
PBRstrm is the provided bit rate of all existing streaming services Thdhsd fr is the admission threshold for streaming PBR decision. It is defined by the Hsdpa streaming PBR threshold parameter PBRbe is the provided bit rate of all existing BE services Thdhsdg fe is the admission threshold for BE PBR decision. It is defined by the Hsdpa best effort PBR threshold parameter GBR is the power requirement for GBR
P p
hsuPa-resis
s
the e
max-hspa' maximum available power for HSPA. Its value is associated with the HSDPA power allocation mode. Ptotai'\s the current downlink transmitted carrier power Pmax is the cell maximum transmitted power Thdtotal_cac is the threshold of cell DL total power, which is defined by the DL total power threshold parameter
P
Page60
tSPw HUAtArEI
By comparing the forecasted ENU load with the corresponding threshold ,the RNC decides whether to accept the access request or not
Page61
# HUAWEI
ENUtotal is the total ENU of all existing users. ENUnew is ENU of the new incoming user. ENUmax is the configured maximum ENU (UL total equivalent user number or DL total nonhsdpa equivalent user number). The threshold for Algorithm2 are the same with Algorithml,for Conv AMR service , Conv non_AMR service , Other R99 services , Handover, HSDPA are set independently:
Admission Threshold UL threshold UL threshold UL threshold UL Handover DL threshold DL threshold DL threshold DL Handover of Conv AMR service of Conv non_AMR service of other services access threshold of Conv AMR service of Conv non_AMR service of other services access threshold
DLDCH
HSDPA
Typically ENU (equivalent number of users) for different services (with activity factor to be 100%) Service*' ENU*' Uplink for DCH+ Downlink for DCH* HSDPA 3.4 kbit/s SIGo 13.6 kbit's SIG+= 3.4 + 12.2 kbit/s*-1 3.4 + 8 kbit/s (PS)+= 3.4 + 16 kbit's (PS)= 3.4 + 32 kbit's (PS>*= 3.4 + 64 kbit/s (PS)+3 0.44*1 1.1 I*1 1.44+' 1.35+' 1.62*= 2.15*' 3.45+= 0.42*5 111*'
1.42*3
0.28*'
0.74+3
-3
1.04+'
1.25*3 2.19+3 3.25+3 5.93+3
3.4 +128 kbit/s (PS)* 5.78*3 3.4 + 144 kbit/s (PS)* 6.41*3 3.4 + 256 kbit's (PS)+ 10.18P 3.4 + 384 kbit/s (PS)* 14.27*=
6.61+=
10.49+3 15.52*3
9.36+=
Admission Threshold UL threshold UL threshold UL threshold UL Handover DL threshold DL threshold DL threshold DL Handover of Conv AMR service of Conv non_AMR service of other services access threshold of Conv AMR service of Conv non_AMR service of other services access threshold
DLDCH
HSDPA
Key parameters
* UL threshold of Conv AMR service a Parameter ID: UlNonCtrlThdForAMR n The default value of this parameter is 75% UL threshold of Conv non_AMR service
Page63
| f t HUAWEI
UL threshold of Conv AMR service Parameter ID: UlNonCtrlThdForAMR Value range: 0 to 1 0 0 % Content: The uplink threshold for the AMR conversational service is used for the uplink admission of AMR conversational service users. The threshold is shared by algorithm 1, algorithm 2 and algorithm 3. The default value of this parameter is 75% Set this parameter through ADD CELLCAC / MOD CELLCAC UL threshold of Conv non_AMR service Parameter ID: UlNonCtrlThdForNonAMR Value range: 0 to 1 0 0 % Content: The downlink threshold for the AMR conversational service is used for the downlink admission of AMR conversational service users. The threshold is shared by algorithm 1, algorithm 2 and algorithm 3. The default value of this parameter is 75% Set this parameter through ADD CELLCAC / MOD CELLCAC
Key parameters
UL threshold of other services a Parameter ID: UlNonCtrlThdForOther n The default value of this parameter is 60% UL Handover access threshold
Page64
H H HUAWEI
UL threshold of other services Parameter ID: UlNonCtrlThdForOther Value range: 0 to 100 % Content: This parameter is the uplink threshold for services other than the conversational service. It is used for uplink admission of other services. The threshold is shared by algorithm 1, algorithm 2 and algorithm 3. The default value of this parameter is 60% Set this parameter through ADD CELLCAC / MOD CELLCAC UL Handover access threshold Parameter ID: UlNonCtrlThdForHo Value range: 0 to 100 % Content: The uplink handover threshold is used for uplink admission of handover users. The parameter is useful only to uplink inter-frequency handovers. Do not make the admission decision in the uplink soft handover. The threshold is shared by algorithm 1, algorithm 2 and algorithm 3. The default value of this parameter is 80% Set this parameter through ADD CELLCAC / MOD CELLCAC
Key parameters
DL threshold of Conv AMR service a Parameter ID: DLCONVAMRTHD n The default value of this parameter is 80% DL threshold of Conv non_AMR service a Parameter ID: DlConvNonAMRThd a The default value of this parameter is 80%
Page6S
H i HUAWEI
DL threshold of Conv AMR service Parameter ID: DLCONVAMRTHD Value range: 0 to 100 % Content: The downlink threshold for the AMR conversational service is used for the downlink admission of AMR conversational service users. The threshold is shared by algorithm 1, algorithm 2 and algorithm 3. The default value of this parameter is 80% Set this parameter through ADD CELLCAC / MOD CELLCAC DL threshold of Conv non__AMR service Parameter ID: DlConvNonAMRThd Value range: 0 to 100 % Content: The downlink threshold for the non-AMR conversational service is used for the downlink admission of non-AMR conversational service users. The threshold is shared by algorithm 1, algorithm 2 and algorithm 3. The default value of this parameter is 80% Set this parameter through ADD CELLCAC / MOD CELLCAC
Key parameters
DL threshold of other services a Parameter ID: DLOTHERTHD D The default value of this parameter is 75% DL Handover access threshold
Page66
0$
HUAWEI
DL threshold of other services Parameter ID: DLOTHERTHD Value range: 0 to 100 % Content: This parameter is the downlink threshold for services other than the conversational service. It is used for downlink admission of users of other services. The threshold is shared by algorithm 1, algorithm 2 and algorithm 3. The default value of this parameter is 75% Set this parameter through ADD CELLCAC/MOD CELLCAC DL Handover access threshold Parameter ID: DLHOTHD Value range: 0 to 100 % Content: The downlink handover threshold is used for downlink admission of handover users. The threshold is shared by algorithm 1, algorithm 2 and algorithm 3. The default value of this parameter is 85% Set this parameter through ADD CELLCAC / MOD CELLCAC
Key parameters
DL total power threshold a Parameter ID: DLCELLTOTALTHD D The default value of this parameter is 90% Hsdpa streaming PBR threshold Parameter ID: HSDPASTRMPBRTHD The default value of this parameter is 70% * Hsdpa best effort PBR threshold a Parameter ID: HSDPABEPBRTHD The default value of this parameter is 70%
Page67
| H | HUAWEI
DL total power threshold Parameter ID: DLCELLTOTALTHD Value range: 0 to 100 % Content: This parameter specifies the total downlink power threshold of the cell. The default value of this parameter is 90% Set this parameter through ADD CELLCAC / MOD CELLCAC Hsdpa streaming PBR threshold Parameter ID: HSDPASTRMPBRTHD Value range: 0 to 100% Content: This parameter specifies the average throughput admission threshold of the HSDPA streaming traffic. The default value of this parameter is 70% Set this parameter through ADD CELLCAC / MOD CELLCAC Hsdpa streaming PBR threshold Parameter ID:: HSDPABEPBRTHD Vaiue range: 0 to 100 % Content: This parameter specifies the average throughput admission threshold of the HSDPA best effort traffic. The default value of this parameter is 70% Set this parameter through ADD CELLCAC / MOD CELLCAC
Key parameters
UL total equivalent user number a Parameter ID: ULTOTALEQUSERNUM D The default value of this parameter is 80 DL total equivalent user number a Parameter ID: DLTOTALEQUSERNUM n The default value of this parameter is 80
Page68
|fc> HUAWEI
UL total equivalent user number Parameter ID: ULTOTALEQUSERNUM Value range: 1 to 200 Content: When algorithm 2 is used, this parameter defines the total equivalent number of users corresponding to the 100% uplink load. The default value of this parameter is 80 Set this parameter through ADD CELLCAC/MOD CELLCAC DL total equivalent user number Parameter ID: DLTOTALEQUSERNUM Value range: 1 to 200 Content: When algorithm 2 is used, this parameter defines the total equivalent number of users corresponding to the 100% downlink load. The default value of this parameter is 80 Set this parameter through ADD CELLCAC / MOD CELLCAC
CE stands for NodeB credit on RNC side and for Channel Element on NodeB side. It is used to measure the channel demodulation capability of the NodeBs The resource of one 12.2kbps voice service, including 3.4kbps signaling on the DCCH, consumed in baseband is defined as one CE. If there is 3.4kbps signaling on the DCCH, but no voice channel, one CE is consumed.The credit resource are divided into several resource pools. Each resource pool is shared by a local cell. According to the common and dedicated channels capacity consumption laws, as well as the addition, removal, and reconfiguration of the common and dedicated channels, the Controlling RNC (CRNC) debits the amount of the credit resource consumed from or credits the amount to the Capacity Credit of the local cell group (and local cell, if any) based on the spreading factor. the UL Capacity Credit and DL Capacity Credit are separate, so the CAC is performed in the UL and DL, respectively. For an RRC connection setup request, the credit resource admission is successful if the current remaining credit resource is sufficient for the RRC connection. For a handover service, the credit resource admission is successful if the current remaining credit resource is sufficient for the service. For other services, the RNC has to ensure that the remaining credit does not exceed the configurable thresholds after admission of the new services. There is no capacity consumption law for HS-DSCH in 3GPP TS 25.433, so certain credits are reserved for HSDPA RAB, and credit admission for HSDPA is not needed. UL Capacity Credit and DL Capacity Credit are separate, the credit resource admission is implemented in the UL and DL, respectively.
' '
:::. . " ' :- :-'.: \:'\fi:::::.::'' :.. : " '. ' :: ;;: " >: :; '
Page70 V i r HUAW61
Spreading Factor
1 2 1 2 1 2 2 6 1 3 2 6 4 10 8 20 384 kbit/s PS 128 kbit/s PS 64 kbit/s PS 32 kbps PS 64 kbit/s VP 12.2 kbit/s AMR 13.6 kbit/s SRB 3.4 kbit/s SRB
128 64 128 64 32 16 64 32 32 16 16 8 8 4
...;.... . . . .'
Page71
2. HUAW61
'
'
...
. ; '.
Direction*
Rate (IcMt/s)*'
Spreading Factor *!
Numljer of CEs C o n s u m e d *?
um
ULP
8-P
w
Q
1.5*3 1.5*= 3*3 3=
2*? 2*
16*3 32-3
ULf
3> *
3*3 6s 6*3 10*= 20*3 20*3 1
tJl> UL*'
UL3 UL* UL*> Ul>3
64*?
128*3 144.3 256*3 384f 608-3
s*10*3 10*3
UL*3
1450'
2SF2-3
32-3
64*3
UL*'
2048.'
2SF2*'
323
64*3
ULP
2890*3
2SF2+2SF4*--
48*3
96*3
UL*>
5760*3
2SF2+2SF4*?
48*J
96*3
<
Key parameters
UI Handover Credit Reserved SF a Parameter ID: UlHoCeResvSf D The default value of this parameter is SF16 Dl Handover Credit and Code Reserved SF a Parameter ID: DlHoCeCodeResvSf The default value of this parameter is SF32
Page72
iPfl HUAWEI
UI Handover Credit Reserved SF Parameter ID: UlHoCeResvSf Value range: SF4, SF8, SF16, SF32, SF64, SF128, SF256, SFOFF Content: The spreading factor specified by this parameter is used to define the uplink credit resource reserved for handover services. SFOFF means that none of resources are reserved for handover services. If the remaining uplink resource cannot fulfill the requirement for the reserved resource after the admission of a new service, the service is rejected. The default value of this parameter is SF16 Set this parameter through ADD CELLCAC / MOD CELLCAC Dl Handover Credit and Code Reserved SF Parameter ID: DlHoCeCodeResvSf Value range: SF4, SF8, SF16, SF32, SF64, SF128, SF256, SFOFF Content: The spreading factor specified by this parameter is used to define the downlink credit and channelized code resources reserved for handover services. SFOFF means that none of the resources is reserved for handover. If the remaining downlink resource cannot fulfill the requirement for the reserved resource after the access of a new service, the service is rejected. The default value of this parameter is SF32 Set this parameter through ADD CELLCAC / MOD CELLCAC
Page73
HUAWEI
A user accessing the network from a path should go through the admission of the path, resource group, and physical port in turn. The user that passes all the admission can be successfully admitted by the transport layer. Path means AAL2 PATH, IP PATH The physical ports correspond to IMA, UNI, FRAATM, NCOPT, ETHER, PPP, and MLPPP. The priority of the 2 types of access follows : Handover >RRC connection setup and Services RAB setup
; :
;
Page74
............
. .. ......
<P' H U A W E I
The Iub overbooking feature considers the statistic multiplexing of service activities and multiple users. Through the admission of more users, Iub overbooking increases the resource utilization on the Iub interface. If the RNC allocates the maximum bandwidth to the subscriber when a service is established, a large proportion of the Iub transmission bandwidth is unused. For example, downloading a 50 KB page takes only about one second, but reading this page needs dozens of seconds. Thus, over 90% of the Iub transmission bandwidth is not used. To save the Iub transmission bandwidth for operator use, Huawei provides the Iub overbooking function, which applies an admission control mechanism to access the service.
Page7S
$% HUAWEI
The UMTS supports four traffic classes: conversational, streaming, interactive, and background. The transmission rate varies with the traffic class as follows: For Circuit Switched (CS) conversational services, the channel transmits voice signals at a certain rate (for example, 12.2 kbit/s) during a conversation and only transmits Silence Descriptors (SIDs) at intervals when there is no conversation. For Packet Switched (PS) interactive and background services, such as web browsing, there is data transmitted during data downloading. After a web page has been downloaded, and when the user is reading the page, however, there is very little data to transfer.
.- .-::~ :-- -
'
'
. ...... ...
4 P w HUAtWVGI
Use SET DEFAULTFACTORTABLE to set a default of Activity Factor table for all the services. Use SET USERGBR to set GBR for BE services
Page77
ififr HUAWa
When the HSDPA_UU_ADCTRL is on, the HSDPA services have to undergo HSDPA user number admission decision. When a new HSDPA service attempts to access the network, it is admitted if the number of HSDPA users in the cell and that in the NodeB do not exceed the associated thresholds When the HSUPA_UU_ADCTRL is on, the HSUPA services have to undergo HSUPA user number admission decision. When a new HSUPA service attempts to access the network, it is admitted if the number of HSUPA users in the cell and that in the NodeB do not exceed the associated thresholds
Key parameters
HSDPA_UU_ADCTRL a Parameter ID: HSDPA_UU_ADCTRL HSDPA user number Maximum
a The default value of this parameter is 64 * HSUPA_UU_ADCTRL a Parameter ID: HSUPA_UU_ADCTRL HSUPA user number
Maximum a
Similar parameters for Maximum HSPA user number in NodeB level can be set by ADD NODEBALGOPARA
Page78
4Pw HUAWGI
Maximum HSDPA user number Parameter ID: MaxHSDSCHUserNum Value range: 0 to 100 Content: This parameter specifies the maximum number of HSDPA users in a cell. The default value of this parameter is 64 Set this parameter through ADD CELLCAC/MOD CELLCAC HSDPA_UU_ADCTRL Parameter ID: HSDPA_UU_ADCTRL Value range: 0 ,1 Content: This parameter specifies whether to enable or disable the HSDPA admission control algorithm. Set this parameter through ADD CELLALGOSWfTCH_/_LST CELLALGOSWITCH/MOD CELLALGOSWITCH HSUPA_UU_ADCTRL Parameter ID: HSUPA_UU_ADCTRL Value range: 0 ,1 Content: This parameter specifies whether to enable or disable the HSDPA admission control algorithm. Set this parameter through ADD CELLALGOSWITCH /MOD CELLALGOSWITCH Maximum HSUPA user number Parameter ID: MaxHsupaUserNum Value range: 0 to 100 Content: This parameter specifies the maximum number of HSDPA users in a cell. The default value of this parameter is 20 Content: This parameter specifies the maximum number of HSUPA users in a celL Set this parameter through ADD CELLCAC / MOD CELLCAC
W Contents
2. Load Control Algorithms 2.1 PUC (Potential User Control) 2.2 LDB (Intra-Frequency Load Balancing) 2 3 CAC (Call Admission Control) 2.4 IAC (Intelligent Admission Control) 2.5 LDR (Load Reshuffling) 2.6 OLC (Overload Control)
Page79
H l | HUAW6I
PageSO
w W HUAWGi
CAC limits the setup of RRC and RAB . When the cell is overloaded , the CAC will cause access failure. In order to improve the access success rate, the Intelligent Access Control (IAC) algorithm is used to improve the access success rate. The IAC procedure includes rate negotiation, Call Admission Control (CAC), preemption, queuing, and Directed Retry Decision (DRD).
AC Overview
ie access procedure (include the IAC)
RRC connection processing
DRD
Failed
Redirection
Succeeded
RAB processing
B setup request
Yes -~~!s t h e r e a n y ~ - ~ ^ ~-~^ce!l n o t tried2< Failed Failed Mo
Rate negotiation
PS domain: maximum rate PS and CS domains: initial rale PS domain; GBR of PS RT service Target Rate Negotiation
Admission algorithm
Load admission Code admission lob resource admission
Queuing
Failed or not supported
Qht )<c
a*-*/ JlJfJ
jy' HAM
As shown in the Figure, the procedure for the UE access includes the procedures for RRC connection setup and RAB setup. The success in the RRC connection setup is one of the prerequisites for the RAB setup. During the RRC connection processing, if resource admission fails, DRD and redirection apply. During the RAB processing, the RNC performs the following steps: Performs RAB DRD to select a suitable cell to access, for service steering or load balancing. Performs rate negotiation according to the service requested by the UE. Performs cell resource admission decision. If the admission is passed, UE access is granted. Otherwise, the RNC performs the next step. Selects a suitable cell, according to the RAB DRD algorithm, from the cells where no admission attempt has been made, and then goes to rate negotiation and cell resource admission again. If all DRD admission attempts to the cells fail, go to the next step. Makes a preemption attempt. If the preemption is successful, UE access is granted. If the preemption fails or is not supported, the RNC performs the next step, queuing. Makes a queuing attempt. If the queuing is successful, UE access is granted. If the queuing fails or is not supported, the RNC Rejects UE access.
81
KZJ
When a new service accesses the network, an RRC connection must be set up first. If the RRC connection request is denied, DRD is performed. If DRD also fails, RRC redirection is performed to direct the UE to an inter-frequency or inter-RAT cell through cell reselection. After the RNC receives the RRC CONNECTION REQUEST message, the CAC algorithm decides whether an RRC connection can be set up between the UE and the current cell. If the RRC connection can be set up between the UE and the current cell, the RNC sends an RRC CONNECTION SETUP message to the UE. If the RRC connection cannot be set up between the UE and the current cell, the RNC takes the following actions: RRC DRD : If the DRD_SWITCH is set to 0, the RRC DRD fails, and RRC redirection is performed. Else, the RNC performs the following steps: 1. The RNC selects inter-frequency neighboring cells of the current cell. These neighboring cells are suitable for blind handovers. 2. The RNC generates a list of candidate DRD-supportive inter-frequency cells. The quality of the candidate cell meets the requirements of inter-frequency DRD: ( C P I C H J E c / N o ) ^ > DRD_Ec/No nbce(| where (CPICH_Ec/No) RACH is the cached CPICH Ec/NO value included in the RACH RRC CONNECTION REQUEST measurement report. DRD_Ec/No nbcel| is the DRD Ec/NO Threshold set for the inter-frequency neighboring cell.
RNC selects a target cell from the candidate cells for UE access. If the candidate cell list contains more than one cell, the UE tries a cell randomly. 1. If the admission is successful, the RNC initiates an RRC DRD procedure. 2. If the admission to a cell fails, the UE tries admission to another cell in the candidate cell list. If all the admission attempts fail, the RNC makes an RRC redirection decision. If the candidate cell list does not contain any cell, the RRC DRD fails. The RNC performs the next step, that is, RRC redirection. RRC redirection, the RNC performs the following steps: 1. The RNC selects all inter-frequency cells of the local cell. 2. The RNC selects candidate cells. That is, exclude the cells to which inter-frequency RRC DRD attempts have been made from the cells selected in the previous step. 3. If more than one candidate cell is available, the RNC selects a cell randomly and redirects the UE to the cell.
Key parameters
* DRD Ec/NO threshold D Parameter ID: DRDEcNOThreshhold The default value of this parameter is -18 (-9 dB) RRC redirect switch D Parameter ID: RrcRedictSwitch D The default value of this parameter is Only_To_lnter_Frequency
Page84
i f e HUAW6J
DRD Ec/NO Threshold Parameter ID: DRDEcNOThreshhold Value range: -24 to 0 ,step :0.5dB Content: This parameter is used as the DRD Ec/No threshold of whether to perform the blind handover. If the Ec/No measured value of the current cell is greater than this parameter of the inter-frequency neighboring cell, this neighboring cell can be selected to be the candidate DRD cell. The default value of this parameter is -18 (-9 dB) Set this parameter through ADD INTERFREQNCELL RRC Redirect switch Parameter ID: RrcRedictSwitch Value range: OFF, Only_To_lnter_Frequency, Allowed_To_lnter_RAT Content: This parameter specifies the RRC redirection strategy. The default value of this parameter is Only_Tb_lnter_Frequency Set this parameter through SET DRD
PageSS
I U HUAW6I
2 negotiation includes the maximum expected rate negotiation, initial rate negotiation, and target rate negotiation. hen setting up, modifying, or admitting a PS service (conversational, streaming, interactive, or background service) the RNC and the CN negotiate the rate according to the UE capability to obtain the maximum expected rate while snsuring a proper QoS. > a non-real-time service in the PS domain, the RNC selects an initial rate to allocate bandwidth for the service r when Setup or UE state transits from CELL_FACH to CELL_DCH based on cell code and credit resource Initial rate selection is affected by 2 algorithm switches: RAB Downsizing Switch, DCCC Switch . "or DCH For HSUPA
*
F->
MmfX'L/DL BE traffic Inifbl bit rate, the negotiated rate based on cell resources) *'
o
iOFF.'
Mimlnitial rate 0/ HSUPA BE traffic, the negotiated rate based on cell resources)."
ON*
ON-"
OFF--
ce
OFF<=
Key parameters
RAB_Downsizing_Switch a Parameter ID: RAB_DOWNSIZING_SWITCH D The default value of this parameter is 1 (on) UL/DL BE traffic Initial bit rate a Parameter ID: a ULBETRAFFINITBITRATE/ DLBETRAFFINITBITRATE a The default value of this parameter is D64 (64k)
Page86
miHm
HUAWG1
RAB_Downsizing_Switch Parameter ID: RAB_DOWNSIZING_SWITCH Value range: (0,1) Content: This parameter specifies whether to support the FJAB downsizing function. The default value of this parameter is 1 (on) When this parameter is set to 1, the FJAB downsizing function is applied to determine the initial bit rate based on cell resources (code and credit).. Set this parameter through SET CORRMALGOSWITCH UL/DL BE traffic Initial bit rate Parameter ID: ULBETRAFFINITBITRATE / DLBETRAFFINITBITRATE Value range: D8, D16, D32, D64, D128, D144, D256, D384, D768, D1024, D1536, D1800, D2048k Content: This parameter defines the uplink initial access rate of background and interactive services in the PS domain. The default value of this parameter is D64 (64k) Set this parameter through SET FRC
Page87
#1HUAWSI
Through the RAB DRD procedure, the RNC selects a suitable cell for RAB processing during access control. RAB DRD is of two types: inter-frequency DRD and inter-RAT DRD. For inter-frequency DRD, the service steering and load balancing algorithms are available. After receiving a RANAP RAB ASSIGNMENT REQUEST, the RNC initiates an RAB DRD procedure to select a suitable cell for RAB processing during access control. The RNC performs inter-frequency DRD firstly. If all admission attempts of interfrequency DRD fail, the RNC performs an inter-RAT DRD. If all admission attempts of inter-RAT DRD fail, the RNC selects a suitable cell to perform preemption and queuing . Relation Between Service Steering DRD and Load Balancing DRD When both service steering DRD and load balancing DRD are enabled, the general principles of inter-frequency DRD are as follows: Service steering DRD takes precedence over load balancing DRD. That is, preferably take service priorities into consideration. To services of the same service priority, load balancing applies.
--
i^ 1
RAB setup
RAB_SETUP_DRD_SWITCH
DRD algorithm switch Parameter ID: DRDSWITCH The default value of this parameter is off Set this parameter through SET CORRMALGOSWITCH
T7
DRD for Service Steering is based on Service priorities of cells .include: - R99 RT services priority - R99 NRT services priority - HSPA services priority - Other services priority
Page89
H i HUAWei
If the UE requests a service in an area covered by multiple frequencies, the RNC selects the cell with the highest service priority for UE access, based on the service type of RAB and the definitions of service priorities in the cells. Cell service priorities help achieve traffic absorption in a hierarchical way. The priorities of specific service types in cells are configurable. If a cell does not support a service type, the priority of this service type is set to 0 in this cell. The service priorities in each cell is called Service priority group , which is identified by the Service priority group Identity parameter. Service priority groups are configured on the LMT. In each group, priorities of R99 RT services, R99 NRT services, HSPA services, and other services are defined. When selecting a target cell for RAB processing, the RNC check the service type firstly , then, selects a cell with a high priority for the service, that is, a cell that has a small value of service priority.
Cell A B
1 2
tftt*
h-M/ m
V::>;
C8SA
RTBorvic*
Page90
HUAWEI
Cell A and cell B are of different frequencies. Assume that the service priority groups given in the table are defined on an RNC, 2 groups of service priorities are defined. Then ,Cell A is configured with service priority group 1. Cell B is configured with service priority group 2 If UE requests a R99 RT service in cell A .Cell B has a higher service priority of the R99 RT service than cell A. If the UE requests an RT service in cell A, preferably, the RNC selects cell B for the UE to access.
[thA i
candidate reques ISPA
jccessfu
#H HUAWEI
The procedure for the service steering DRD is as follows: 1. The RNC determines candidate cells to which blind handovers can be performed and sorts the candidate cells into a descending order according to service priority. A candidate cell must meet the following conditions: The frequency of the candidate cell is within the band supported by the UE. The quality of the candidate cell meets the Ec/No requirements of inter-frequency DRD (DRD Ec/NO Threshold ) The candidate cell supports the requested service. 2> The RNC selects a target cell from the candidate cells in order of service priority for UE access. 3. The CAC algorithm makes an admission decision based on the status of the target cell. If the admission attempt is successful, the RNC accepts the service request. If the admission attempt fails, the RNC removes the cell from the candidate cells and then choose next candidate cell. 4, If admission decisions have been made in all the candidate cells For HSPA access, the HSPA request falls back to a DCH one. Then, the algorithm goes back to Step 1 to make an admission decision based on R99 service priorities. For DCH access, the RNC initiates an inter-RAT DRD.
Key parameters
DRD Ec/NO Threshold a Parameter ID: DRDEcNOThreshhold o The default value of this parameter is -18 (-9dB) Service differential drd switch
Parameter ID: ServiceDiffDrdSwitch o The default value of this parameter is OFF Service priority group Identity
Page92
W W
HUAWEI
DRD Ec/NO Threshold Parameter ID: DRDEcNOThreshhold Value range: -24-0 .Step: 0.5dB Content: This parameter is used as the DRD Ec/No threshold of whether to perform the blind handover. If the Ec/No measured value of the current cell is greater than this parameter of the inter-frequency neighboring cell, this neighboring cell can be selected to be the candidate DRD cell. The default value of this parameter is -18. Set this parameter through ADD INTERFREQNCELL Service differential drd switch Parameter ID: ServiceDiffDrdSwitch Value range: ON, OFF Content: This parameter specifies whether to enable the service steering DRD algorithm The default value of this parameter is OFF. Set this parameter through ADD CELLDRD/SET DRD Service priority ofR99 RT service Parameter ID: Spgld Value range: 1 to 8 Content: This parameter uniquely identifies a group of service priorities that map to cells and indicate the support of each cell for the following service types: R99 RT service, R99 NRT service, HSPA service, and other services. Set this parameter through ADD SPG When define a cell by ADD CELLSETUP, this SPG ID is a mandatory parameter
Key parameters
Service priority of R99 RT service o Parameter ID: Spgld Service priority of R99 NRT service PriorityServiceForR99NRT Service priority of HSPA service a PriorityServiceForHSPA Service priority of Other service a PriorityServiceForExtRab
Copyright <> 2009 Huawei Technologies Co., Ltd. All rights reserved. S
Page93
|i|HUAWei
Service priority of R99 RT service Parameter ID: PriorityServiceForR99RT Value range: 0 to 7 Content: This parameter specifies the support of the cells with a specific Service priority group Identity for R99 RT services. The value 0 means that these cells do not support R99 RT services. For the values 1 through 7, the service priority is inversely proportional to the value, that is, the value 7 indicates the lowest service priority, whereas the value 1 indicates the highest. Set this parameter through ADD SPG
Service priority of R99 NRT service Parameter ID: PriorityServiceForR99NRT Value range: 0 to 7 Content: This parameter specifies the support of the cells with a specific Service priority group Identity for R99 NRT services. The value 0 means that these cells do not support R99 NRT services. For the values 1 through 7, the service priority is inversely proportional to the value, that is, the value 7 indicates the lowest service priority, whereas the value 1 indicates the highest. Set this parameter through ADD SPG Service priority of HSPA service Parameter ID: PriorityServiceForHSPA Value range: 0 to 7 Content: This parameter specifies the support of the cells with a specific Service priority group Identity for HSPA services. The value 0 means that these cells do not support HSPA services. For the values 1 through 7, the service priority is inversely proportional to the value, that is, the value 7 indicates the lowest service priority, whereas the value 1 indicates the highest. Set this parameter through ADD SPG Service prionty of Other service
Parameter ID: PriorityServiceForExtRab Value range: 0 to 7 Content: This parameter specifies the support of the cells with a specific Service priority group Identity for Other services . The value 0 means that these cells do not support Other service . For the values 1 through 7, the service priority is inversely proportional to the value, that is, the value 7 indicates the lowest service priority, whereas the value 1 indicates the highest. Set this parameter through ADD SPG
D Any of these 2 resources can trigger inter-frequency DRD for Load Balance
Page9S
4$ HUAWEI
Load balancing considers two resources: power, and code. In practice, it is recommended that only either a power-based load balancing DRD or a code-based load balancing DRD is activated. If both are activated, power-based load balancing DRD takes precedence over code-based load balancing DRD. Code-based load balancing DRD is applicable to only R99 services because HSDPA services use reserved codes.
Copyright 2009 Huawei Technologies Co., Ltd. All rights reserved. Page96 W W HUAWEI
: I.
Two algorithms are available for power load balancing. If the power load balancing DRD is enabled, one of them can be used, and the algorithm used is defined by the Load balance DRD choice parameter. Algorithm 1: The load balancing DRD is performed according to the cell measurement values about the DL non-HSDPA power and DL HS-DSCH required power. For DCH service, the RNC sets up the service on a carrier with a light load of non-HSDPA power to achieve load balancing among the cells on the different frequencies. For HSDPA service, the RNC sets up the service on a carrier with a light load of HS-DSCH required power to achieve load balancing among the cells on different frequencies. Algorithm 2: The load balancing DRD is performed according to the DCH Equivalent Number of Users (ENU) and HSDPA user number. For DCH service, the RNC sets up the service on a carrier with a light load of DCH ENU to achieve load balancing among the cells on different frequencies. For HSDPA service, the RNC sets up the service on a carrier with a light toad of HSDPA user to achieve load balancing among the cells on different frequencies.
Inter-frequency DRD
>ower load balancing DRD
Receive a service request
oes power of a neighboring cell meet DRD conditions edition 2)? HSPA falls back to DCH Are there multiple such cells available?
Yes
Select the cell meeting the DRD conditions as the target ceil
Select the cell with the lightest power load as the target ceil
-^
CAC successful?
initiate an interRAT DRD The procedure for power-based load balancing DRD is as follows:
The RNC determines the candidate cells to which blind handovers can be performed. The frequency of the candidate cell is within the band supported by the UE.
A candidate cell must meet the following conditions: The quality of the candidate cell meets the requirements of inter-frequency DRD. The candidate cell supports the requested service.
2. If the current cell is not a candidate cell, the RNC selects a cell with the lightest load from the candidate cells as the target cell to do admission for the service. If the current cell is a candidate cell as well, RNC need to consider the current cell load condition (condition - !, described below), if current cell load is not higher than a threshold , means conditionl is met, RNC just do admission for the service in the current cell regardless the neighbors. Otherwise (conditionl is not met) ,RNC need to evaluate the load difference between the current cell and other candidate neighbors, if the load difference between current cell and a neighbor is larger than a threshold (concition2, described below), then this neighbor is an available target cell. After the filtration of the conditionl and condition2, If there are multiple such ceils , RNC select the cell with lightest load as the target cell, (the method to select the cell with lightest load is described below. ). If there is no such cell, the RNC selects the current cell as the target c e l l . The CAC algorithm makes an admission decision on the target cell. If the admission attempt is successful, the RNC admits the service request. If the admission attempt fails, the RNC checks whether admission decisions have been made in all candidate inter-frequency neighboring cells. If there is any cell where no admission decision is made, the algorithm goes back to 2. If admission decisions have been made in all the candidate cells: When the service request is an HSPA one, the HSPA request falls back to a DCH one. Then, the algorithm goes back to 1 to make an admission decision based on R99 service priorities. When the service request is a DCH one, the RNC initiates an inter-RAT DRD.
$
y ^
4 ""non-H ^ ^ "C'H
o/HM"*^ ^
>
_ P
Where cutcell H-tie ,cutcell
)lThdH_ttecutcell>ThdH
Thd.
Thd,,
is Dl load balance DRD power remain threshold for DCH of the current cell, is Dl load balance DRD power remain threshold for HSDPA of the current cell.
*GBP,nbcell
P
GBP,cutcell
) > ThdH
load,cutcell
)-(Thd
K load
,nbcell
*non-H
,nbcell )
\* ""
AMR, cutcell
*non-H
.cutcell )
""DJc--
yl TIMtotai
cutceu
~ * load,cutcell
V ^total,nbcell
"load ,nbcell )
<
* "^total
Joado
yi ndH_uenbceU
\f "&H-ite,cutcell
^H-rn,cutcell ) ' *
""H-iue.cuh
>ThdH Joadoffset
b. For a DCH service
[Thd
AMR,nbcell
- p
D-enu,nbcell
)-(Thd
AMR,cutcell
D-enu,cutcell
) > ThdD
loadoffsi
Current cell
--- - - Description DL total power threshold HS-DSCH re quired power load (GBP) Total power load. It is the sum of the non-HSDPA power and GBP. Non-HSDPA power load DL threshold of Conv AMR service Maximum HSDPA user number Number of all existing HSDPA users Total ENU of all existing DCH services Load balance DRD offset for HSDPA Load balance DRD offset for DCH Load balance DRD total power protect threshold
**Malma&
1
p
G2?f!&ce&
p
SSPjttvdl
P
P
1 rWjt&jaixdt
P
hadtHbce8 p
HM-JixicsS
1
^"JMB,S**
^^H-ucci&eE
2 ^jyHBf,M1a?S
p p
Pif-mxiedl
p -
*dB&ad&a
*"" n.ba&&iet
* ""fitt!J^xa&>jtf
Key parameters
Load balance DRD switch for DCH
o Parameter ID: LdbDrdSwitchDCH n The default value of this parameter is OFF
PagelOO
iPflHUAWei
Key parameters
Dl toad balance DRD power remain threshold for DCH
a Parameter ID: LdbDRDLoadRemainThdDCH The default value of this parameter is 35%
PagelOl
igfm HUAWEI
Dl load balance DRD power remain threshold for DCH Parameter ID: LdbDRDLoadRemainThdDCH
Key parameters
DL total power threshold
a Parameter ID: DLCELLTOTALTHD a The default value of this parameter 90%
| | # HUAWEI
DL total power threshold Parameter ID: DLCELLTOTALTHD Value range: 0-100% Content: Admission threshold of the total cell downlink power. If the value is too high, too many users will be admitted. However, the throughput of a single user is easy to be limited. If the value is too low, cell capacity will be wasted. The default value of this parameter is 90% Set this parameter through SET DRD Load balance DRD offset for DCH Parameter ID: LdbDRDOffsetDCH Value range: 0-100% Content: This parameter specifies the threshold of remanent load offset between the current cell and the target cell when load balancing DRD is applied for DCH users. Only when the remanent load offset reaches this threshold can a neighboring cell be selected as a candidate DRD cell for DCH users. The default value of this parameter is 10%. Set this parameter through SET DRD Load balance DRD offset for HSDPA Parameter ID: LdbDRDOffsetHSDPA Value range: 0-100% Content: This parameter specifies the threshold of remanent load offset between the current cell and the target cell when load balancing DRD is applied for HSDPA users. Only when the remanent load offset reaches this threshold can a neighboring cell be selected as a candidate DRD cell for HSDPA users. The default value of this parameter is 10% Set this parameter through SET DRD Load balance DRD total power protect threshold Parameter ID: LdbDRDTotalPwrProThd Value range: 0% to 100% Content: This parameter specifies the threshold of the downlink remanent total power difference between the current cell and the target cell when load balancing DRD is applied and the load balancing DRD choice is Power. Only when the downlink remanent total power difference is less than this threshold can a neighboring cell be selected as a candidate DRD cell. Set this parameter through SET DRD
Z - Inter-frequency DRD
Inter-Frequency DRD procedure for Code Load Balance
No
Yes
Yes
No
ortcd
Yes
The procedure is as follows: 1. The RNC determines whether the minimum remaining spreading factor of the current cell is smaller than Minimum SF threshold for code balance DRD. If the minimum SF is smaller than Minimum SF threshold for code balance DRD, the RNC tries the admission of the service request to the current cell. If the minimum SF is not smaller than Minimum SF threshold for code balance DRD, the RNC performs the next step. 2. The RNC determines whether the code load of the current cell is lower than Code occupied rate threshold for code balance DRD. If the code load is lower than Code occupied rate threshold for code balance DRD, the service tries the admission to the current cell. If the code load is higher than or equal to Code occupied rate threshold for code balance DRD, the RNC selects the cell with the lightest load or the current cell as the target cell. The RNC selects the cell as follows: If the minimum SF supported by the cell with the lightest code load is the same as the minimum SF supported by the current cell, and the difference between the code resource occupancies of the cell and the current cell is larger than or equal to the value of Delta code occupied rate, the RNC selects the cell with the lightest code load as the target cell. Otherwise, the RNC selects the current cell as the target cell. If the minimum SF supported by the cell with the lightest code load is smaller than the minimum SF supported by the current cell, the RNC selects the cell with the lightest code load as the target cell.
103
Key parameters
Code balancing drd switch n Parameter ID: CodeBalancingDrdSwitch The default value of this parameter is OFF Minimum SF threshold for code balancing a Parameter ID: CodeBalancingDrdMinSFThd n The default value of this parameter is SF8 drd
Pagel 04
4$$ HUAWEI
Code balancing drd switch Parameter ID: CodeBalancingDrdSwitch Value range: ON, OFF Content: This parameter specifies whether to enable the code-based load balancing DRD algorithm. The default value of this parameter is OFF. Set this parameter through SET DRD / ADD CELLDRD Minimum SF threshold for code balancing drd Parameter ID: CodeBalancingDrdMinSFThd Value range: SF4, SF8, SF16, SF32, SF64, SF128, SF256 Content: If the downlink minimum SF of the best cell is below this threshold, the code-based load balancing DRD is not triggered. The default value of this parameter is SF8 . Set this parameter through SET DRD / ADD CELLDRD
Key parameters
Code occupied rate threshold for code balancing a Parameter ID: CodeBalancingDrdCodeRateThd n The default value of this parameter is 13% drd
rate
Page! 05
H i HUAW6I
Code occupied rate threshold for code balancing drd Parameter ID: CodeBalancingDrdCodeRateThd Value range: 0% to 100% Content: This parameter specifies the code occupancy threshold of the current cell for code-based load balancing DRD.Only when the code occupancy of the best cell reaches this threshold can code-based load balancing DRD be triggered. The default value of this parameter is 13%. Set this parameter through SET DRD / ADD CELLDRD Delta code occupied rate Parameter ID: DeltaCodeOccupiedRate Value range: 0% to 100% Content: This parameter specifies the code occupied rate offset threshold of the current cell and the inter-frequency cell when code balancing drd algorithm is applied. Only when the code occupied rate offset reaches this threshold, the inter-frequency cell can be selected to be the target drd cell. The default value of this parameter is 7% . Set this parameter through SET DRD
generated?
Try admission to the target cell in order of blind handover priority Adm Max itiate an inter-RAT handover Preemption or queuing
The inter-RAT DRD procedure is as follows: 1,If the current cell is configured with any neighboring GSM cell suitable for blind handover and the Service Handover Indicator is set to HO_TO_GSM_SHOULD_BE_PERFORM, the RNC performs next step. Otherwise, the service request undergoes preemption and queuing. 2,The RNC generates a list of candidate DRD-supportive inter-RAT cells that fulfill the following requirement:
(CPICH_EcNo)
where
- (CPICH_EcNo)RACH is t h e cached CPICH Ec/NO value included in the RACH measurement report. - (DRD_EcNo)nbcell is the DRD Ec/NO Threshold set for the inter-RAT neighboring cell. 3,The service request then tries admission to a target GSM cell in order of blind handover priority. 4,lf all admission attempts fail or the number of inter-RAT directed retries exceeds 2, the service request undergoes preemption and queuing. Inter-RAT DRD is only available for AMR service in RAN 10:
Key parameters
DRD Ec/NO Threshold n Parameter ID: DRDEcNOThreshhold n The default value of this parameter is -18 (-18dB) * Max inter-RAT direct retry number p Parameter ID: DRMaxGSMNum The default value of this parameter is 2
Page107
lliHUAwei
DRD Ec/NO Threshold Parameter ID: DRDEcNOThreshhold Value range: -24-0 , Content: This parameter is used as the DRD Ec/No threshold of whether to perform the blind handover. If the Ec/No measured value of the current cell is greater than this parameter of the inter-RAT neighboring cell, this neighboring cell can be selected to be the candidate DRD cell. The default value of this parameter is -18. Set this parameter through ADD GSMNCELL Max inter-RAT direct retry number Parameter ID: DRMaxGSMNum Value range: 0 to 5 Content: This parameter defines the maximum number of inter-RAT directed retries for an RAB. The value 0 means that inter-RAT DRD is not allowed. The default value of this parameter is 2 Set this parameter through ADD CELLDRD
Page108
HUAWEI
Preemption and Queuing guarantees the success in the access of a higher-priority user by forcibly releasing the resources of a lower-priority user. After cell resource admission fails, the RNC performs Preemption and Queuing if the following conditions are met: The RNC receives an RAB ASSIGNMENT REQUEST message indicating that Preemption and Queuing is supported. By default, Preemption and Queuing setting in CN may be:
USER LEVEL High Medium Low
I Not able
_ _ . , , JL_ , _ . _ _ _ _ .
Preemption and Queuing is applicable to the following cases: Setup or modification of a service Q Hard handover or SRNS relocation UE state transits from CELL_FACH to CELL_DCH The RNC selects a suitable cell according to the settings of the DRD algorithms.
<yi
Preemption
'motion on different resources 1 Service Resource Service That cat Be Preempted R99 Service | R99 service Code Power CE Iub bandwidth HSDPA Code Power CE J V 7 V V V V V V V V V V V V V V V V HSUPA Service HSDPA Service R99 + HSPA Combined Service V V V V V ~J V V
1
HSUPA
The preemption procedure is as follows: 1 > The preemption algorithm determines which radio link sets can be preempted. The algorithm proceeds as follows: n Chooses SRNC users first. If no user under the SRNC is available, the algorithm chooses users under the DRNC. Sorts the pre-emptable users by user integrate priority, or sorts the preemptable RABs by RAB integrate priority. Determines candidate users or RABs. a Only the users or RABs with priorities lower than the RAB to be established are selected.
a Selects as many users or RABs as necessary in order to match the resource needed by the RAB to be established. When the priorities of two users or RABs are the same, the algorithm chooses the user or RAB that can release the most resources. 2^ The RNC releases the resources occupied by the candidate users or RABs. 3> The requested service directly uses the released resources to access the network without admission decision.
Key parameters
Preempt algorithm switch
a Parameter ID: PREEMPTALGOSWITCH a The default value of this parameter is OFF
Pagel10
<||i| HUAWEI
Preempt algorithm switch Parameter ID: PreemptAlgoSwitch Value range: ON, OFF Content: This parameter specifies whether to support the preemption function. The default value of this parameter is OFF Set this parameter through SET QUEUEPREEMPT
IAC-Queuing
After Preemption rejection, UE can wait in queue, then admission attempts for the service are made periodically till
Tmax expires.
-HI (101
Copyright 2009 Huawei Technologies Co., Ltd. All rights reserved.
Pagelll
^ # HUAWEI
After the cell resource decision fails, the RNC performs queuing if the RNC receives an RAB ASSIGNMENT REQUEST message indicating the queuing function is supported The queuing algorithm checks whether the queue is full, that is, whether the number of service requests in the queue exceeds the queue length that is defined by the Queue length The queuing algorithm is triggered by the heartbeat timer, which is set through the Poll timer length . If the queue is not full: Stamps this request with the current time. Puts this request into the queue. Checks whether there are requests whose integrate priorities are lower than that of the priority of the new request. If there is, delete the low priority request, put the new service in the queue. (Otherwise, the queuing algorithm rejects the new request directly.) Stamps the new request with the current time and then puts it into the queue. Selects the request with the highest integrate priority for an attempt of resource allocation . If more than one service has the same highest integrate priority, the RNC calculates the weights of the requests with the same highest integrate priority and chooses the request with the greatest weight for an attempt of resource allocation. The Weight = Telapsed If the attempt fails, the queuing algorithm proceeds as follows: Puts the service request back into the queue with the time stamp unchanged for the next attempt. Chooses the request with the greatest weight from the rest and makes another attempt until a request is accepted or all requests are rejected.
After the heartbeat timer (Poll timer length) expires, the queuing algorithm proceeds as follows:
Key parameters
* Queue algorithm switch a Parameter ID: QUEUEALGOSWITCH a The default value of this parameter is OFF Queue length p Parameter ID: QUEUELEN a The default value of this parameter is 5
: '.:"':';:':. - ' . . .: Copyright 2009 Huawei Technologies Co., Ltd. All rights reserved.
Page! 12
l U l HUAW6I
Queue algorithm switch Parameter ID: QUEUEALGOSWITCH Value range: ON, OFF Content: This parameter specifies whether to support the queuing function. The default value of this parameter is OFF Set this parameter through SET QUEUEPREEMPT Queue length Parameter ID: QUEUELEN Value range: 5 to 20 Content: This parameter defines the length of a queue. The default value of this parameter is 5 Set this parameter through SET QUEUEPREEMPT
A.
Key parameters
Poll timer length D Parameter ID: POLLTIMERLEN D The default value of this parameter is 50 (500ms) Max queuing time length
Pagel 13
| | | H U A W I
Poll timer length Parameter ID: POLLTIMERLEN Value range: 1 to 6000 , step: 10ms Content: This parameter defines the length of the heartbeat timer. Each time the timer expires, the RNC chooses the service that meets the requirement to make an admission attempt. The default value of this parameter is 50 (500ms) Set this parameter through SET QUEUEPREEIVJPT Max queuing time length Parameter ID: MAXQUEUETIMELEN Value range: 1 to 60s Content: This parameter defines the maximum time that the service request can be in the queue. The default value of this parameter is 5s Set this parameter through SET QUEUEPREEMPT
Page114
W W
HUAWEI
Compared with the RRC connection process of ordinary services, the RRC connection process of emergency calls incorporates the preemption due to hard resource admission failure. In case of power resources, direct admission is used without considering the CAC algorithm switch. In case of hard resources, (that is, code, Iub, and CE), the resource admission is successful if the current remaining resources are sufficient for the RRC connection. If the hard resource admission fails, preemption is performed regardless of whether the preemption switch is on or off. The emergency calls that trigger preemption have the highest priority. The range of users that can be preempted is defined by the Preemptvulnerability for emergency call switch parameter. If this switch is set to ON, all non-emergency users that have accessed the network can be preempted, regardless of the preemption-prohibited attribute of the users. If this switch is set to OFF, only the non-emergency users with preemption-allowed attribute can be preempted.
<
x4-
HUAWEI
In case of power resources: If the CAC algorithm switch is on, regardless of which algorithm is selected, the admission decision-making is as follows: When EMC_UU_ADCTRL (set through Cell CAC algorithm switch) is on, power admission fails if the system is in overload congestion state. Otherwise, the admission succeeds. When EMC_UU_ADCTRL is off, the emergency calls are directly admitted. If the CAC algorithm switch is off, the emergency calls are directly admitted. For hard resources (that is, code, Iub, and CE), the resource admission is successful if the current remaining resources are sufficient for the request. If the hard resource admission fails, preemption is performed regardless of whether the preemption switch is on or off. The emergency calls that trigger preemption have the highest priority. The range of users that can be preempted is defined by the Preemptvulnerability for emergency call switch parameter. If this switch is set to ON, all non-emergency users that have accessed the network can be preempted, regardless of the preemption-prohibited attribute of the users. If this switch is set to OFF, only the non-emergency users with preemption-allowed attribute can be preempted.
Key parameters
Preemptvulnerability for emergency call switch Parameter ID: EmcPreeRefVulnSwitch The default value of this parameter is ON (All services)
Pagel 16
: wPW HUAWEI
Preemptvulnerability for emergency call switch Parameter ID: EmcPreeRefVulnSwitch Value range: ON, OFF Content: When the switch is enabled, users of emergency call can preempt all the users of non emergency call. When the switch is disabled, users of emergency call can only preempt users of non emergency call with the preempted attributes. The default value of this parameter is ON Set this parameter through SET QUEUEPREEMPT
& ) Contents
Load Control Algorithms 2.1 PUC (Potential User Control) 2.2 LDB (Intra-Frequency Load Balancing) 2.3 CAC (Call Admission Control) 2.4 IAC (intelligent Admission Control) 2.5 LDR (Load Reshuffling) 2.6 OLC (Overload Control)
Page117
HUAWEI
m o
100/
u
section B section C
THL
Junes
Copyright 2009 Huawei Technologies Co., Ltd. All rights reserved. Pagel 18
HUAWEI
LCC (Load Congestion Control) consist of LDR (Load Reshuffling) and OLC (Over Load Control). In basic congestion state, LDR will be used to optimize resource distribution, the main rules is not to affect the feeling of users as possible as we can. In overload state, OLC will be used to release overload state quickly, keep system stability and the service of high priority users.
Load Reshuffling
Reasons D When the ceil is in basic congestion state, new coming calls could be easily rejected by system Purpose a Optimizing cell resource distribution a Decreasing load level, increasing admission successful rate
Page119
0r- HUAWEI
When the usage of cell resource exceeds the basic congestion triggering threshold, the cell enters the basic congestion state. In this case, LDR is required to reduce the cell load and increase the access success rate.
Load Reshuffling
Triggering of LDR Power resources n Code resource a Iub resources D NodeB Credit resource
Page120
4PH HUAWEI
For power resource, the RNC performs periodic measurement and checks whether the cells are congested. For code, Iub, and NodeB credit resources, event-triggered congestion applies, that is, the RNC checks whether the cells are congested when resource usage changes.
Load Reshuffling
LDR Actions: D D n D a D Inter-frequency load handover Code reshuffling BE service rate reduction AMR rate reduction Inter-RAT load handover in the CS domain Inter-RAT load handover in the PS domain Real time service Iu QoS renegotiation MBMS power reduction
Page121
l U l HUAWEI
When the cell is in basic congestion state, the RNC takes one of the actions in each period until the congestion is resolved j(yxKi^
~ft\\r>JJA
-Jj,
f^M
ik
Power
UL
4 4 4 V
4*
4*
DL
Credit
UL
DCH HSUPA
4 4 4
4 V
DL
If the downlink power admission uses the equivalent user number algorithm, basic congestion can also be triggered by the equivalent number of users. In this situation, LDR actions do not involve AMR rate reduction or MBMS power reduction, as indicated by the symbol "*" in above table Congestion of different resource may trigger different actions. For example, Credit congestion do not trigger "Inter-Frequency Load Handover", "AMR Rate Reduction", and "Code Reshuffling" When congestion of all resources is triggered, the action to be taken is based on the resource priority configuration.
\ \
Key parameters
Cell LDC algorithm switch a Parameter ID: NBMLDCALGOSWITCH . UL_UU_LDR . DL_UU_LDR . CELL_CODE_LDR NodeB LDC algorithm switch M-.pvw '"
Page! 23
| P | HUAWEI
Cell LDC algorithm switch Parameter ID: NBMLDCALGOSWITCH Value range: ON, OFF Content: If ULLDR, DLLDR, CELL_CODE_LDR are selected, the corresponding algorithms are enabled.. Set this parameter through ADD CELLALGOSWITCH / MOD CELLALGOSWITCH NodeB LDC algorithm switch Parameter ID: NodeBLdcAlgoSwitch Value range: ON, OFF Content: If IUB_LDR, NODEB_CREDIT_LDR, are selected, the corresponding algorithms will be enabled; otherwise, disabled.. Set this parameter through ADD NODEBALGOPARA / MOD NODEBALGOPARA / SET LDCALGOPARA
Key parameters
UL (RTWP) LDR trigger threshold D Parameter ID: ULLDRTRIGTHD The default value of this parameter is 55%
threshold
Pagel24
| P HUAWEI
UL LDR trigger threshold Parameter ID: ULLDRTRIGTHD Value range: 0 to 100 , % Content: If the UL load of the cell is not lower than this threshold, the UL load reshuffling function of the cell is triggered. The default value of this parameter is 55% Set this parameter through ADD CELLLDM/MOD CELLLDM UL LDR release threshold Parameter ID: ULLDRRELTHD Value range: 0 to 100 , % Content: If the UL load of the cell is lower than this threshold, the UL load reshuffling function of the cell is stopped. The default value of this parameter is 45% Set this parameter through ADD CELLLDM / MOD CELLLDM
Key parameters
DL (TX POWER) LDR trigger threshold a Parameter ID: DLLDRTRIGTHD o The default value of this parameter is 70%
threshold
. .::::::::::. .-:;:::::::: :: :
Page125 WW HUAIWEI
DL LDR trigger threshold Parameter ID: DLLDRTRIGTHD Value range: 0 to 100, % Content: If the DL load of the cell is not lower than this threshold, the DL load reshuffling function of the cell is triggered. The default value of this parameter is 70% Set this parameter through ADD CELLLDM / MOP CELLLDM DL LDR release threshold Parameter ID: DLLDRRELTHD Value range: 0 to 100, % Content: If the DL load of the cell is lower than this threshold, the DL load reshuffling function of the cell is stopped. The default value of this parameter is 60% Set this parameter through ADD CELLLDM / MOP CELLLDM
Key parameters
Cell LDR SF reserved threshold a Parameter ID: CELLLDRSFRESTHD p The default value of this parameter is SF8 UI LDR Credit SF reserved threshold
u Parameter ID: ULLDRCREDITSFRESTHD The default value of this parameter is SFS Dl LDR Credit SF reserved threshold
Page126
i P f HUAWEI
Cell LDR SF reserved threshold Parameter ID: CELLLDRSFRESTHD Value range: SF4, SF8, SF16, SF32, SF64, SF128, SF256 Content: If the SF corresponding to the current remaining code of the cell is higher than the threshold defined by this parameter, code congestion is triggered and the related handling actions are taken. The default value of this parameter is SF8 Set this parameter through ADD CELLLDR / MOD CELLLDR UI LDR Credit SF reserved threshold Parameter ID: ULLDRCREDITSFRESTHD Value range: SF4, SF8, SF16, SF32, SF64, SF128, SF256 Content: If the SF corresponding to the current UL remaining credit resource is higher than the threshold defined by this parameter, the UL credit LDR can be performed and the related handling actions are taken. The default value of this parameter is 60% Set this parameter through ADD NOPEBLDR/MOD NODEBLDR Dl LDR Credit SF reserved threshold Parameter ID: DLLDRCREDITSFRESTHD Value range: SF4, SF8, SF16, SF32, SF64, SF128, SF256 Content: If the value of SF corresponding to the current DL remaining credit resource is higher than the threshold defined by this parameter, the DL credit LDR can be performed and the related handling actions are taken. The default value of this parameter is SF8 Set this parameter through ADD NQDEBLDR/MOD NODEBLDR
Key parameters
The First / Second/ Third/ Fourth priority for a Parameter ID: LdrFirstPri LdrSecondPri LdrThirdPri LdrFourthPri a The default configuration is : . lUBLDR > CREDITLDR > CODELDR > UULDR load reshuffling
Page127
l i d HUAWEI
The First / Second/ Third/ Fourth priority for load reshuffling Parameter ID: LdrFirstPri / LdrSecondPri / LdrThirdPri / LdrFourthPri Value range: IUBLDR(lub load reshuffling), CREDITLDR(Credit load reshuffling), CODELDR (Code load reshuffling), UULDR (Uu load reshuffling) Content: These parameters specify the triggering resource order when congestion of all resources are triggered. The default configuration is lUBLDR > CREDITLDR > CODELDR > UULDR Set this parameter through SET LDCALGOPARA
LDR procedure
Turn on LDR algorithm switch Mark "current LDR state = uncongested1
Inter-freq oad handover Code reshuffling BE rate reduction Sequence of actions can be configured (current action is taken firstly) Inter-system handover in CS domain Inter-system handover In PS domain AMR rate reduction QoS renogiation on Iu interface
Succeed?
action duration
Succeed?
MBMS power reduction No related action can be found Mark current action first LDR action"
V,
Key parameters
LDR period timer length a Parameter ID: LDRPERIODTIMERLE D The default value of this parameter is 10 s
Switch
Page129
$(1 HUAWEI
LDR period timer length Parameter ID: LDRPERIODTIMERLE Value range: 0 to 86400 s Content: This parameter specifies the period of load reshuffling . The default value of this parameter is 10 s Set this parameter through SET LDCPERIOD Gold User Load Control Switch Parameter ID: GoldUserLoadControlSwitch Value range: ON, OFF Content: This parameter specifies whether LDR actions are applicable to users of gold priority. The default value of this parameter is OFF Set this parameter through ADD CELLLDR / MOP CELLLDR
Key parameters
DL LDR first / second / third /fourth eighth / ninth / tenth action /fifth / sixth / seventh /
a Parameter ID: DILdrFirstAction / DILdrSecondAction / DILdrThirdAction / DILdrFourthAction / DILdrFifthAction / DILdrSixthAction / DILdrSeventhAction / DlLdrEighthAction / DlLdrNinthAction / DILdrTenthAction The default configuration is : . 1st:CODEADJ , 2 nd : INTERFREQLDHO , 3rd: BERATERED
Page130
V w
HUAWEI
DL LDR first/second/third/fourth/fifth/sixth/seventh/eighth/ninth/tenth
action
Parameter ID: DILdrFirstAction / DILdrSecondAction / DILdrThirdAction / DILdrFourthAction / DILdrFifthAction / DILdrSixthAction / DILdrSeventhAction / DlLdrEighthAction / DlLdrNinthAction / DILdrTenthAction Value range: NOACT (NO ACTION), INTERFREQLDHO (INTER-FREQ LOAD HANDOVER), BERATERED (BE TRAFF RATE REDUCTION), QOSRENEGO (UNCONTROLLED REAL-TIME TRAFF QOS RE-NEGOTIATION), CSINTERRATSHOULDBELDHO (CS DOMAIN INTER-RAT SHOULD BE LOAD HANDOVER), PSINTERRATSHOULDBELDHO (PS DOMAIN INTER-RAT SHOULD BE LOAD HANDOVER), AMRRATERED (AMR TRAFF RATE REDUCTION), MBMSDECPOWER(MBMS DESCEND POWER), CODEADJ(CODE ADJUST), CSINTERRATSHOULDNOTLDHO (CS DOMAIN INTER-RAT SHOULD NOT BE LOAD HANDOVER), PSINTERRATSHOULDNOTLDHO (PS DOMAIN INTER-RAT SHOULD NOT BE LOAD HANDOVER). Content: These parameters specify the LDR action order. The default configuration is 1st:CODEADJ , 2 n d : INTERFREQLDHO , 3 rd : BERATERED, Set this parameter through ADD CELLLDR / MOD CELLLDR / ADD NODEBLDR / MOP NODEBLDR
V^
LDR Actions
Inter-frequency load handover n Target users
' ^ * A4 \ c\ s Xtfv^oi
. Current bandwidth for DCH or "GBR bandwidth for HSPA" has to be less than the UL/DL Inter-freq cell load handover maximum bandwidth parameter
Target cells
Load difference between current load and the basic congestion trigger threshold of target cell is larger than "UL/DL Inter -freq cell load handover load space threshold"
Page! 31
H H HUAWEI
implemented as follows: The LDR check whether the existing cell has a target cell of inter-frequency blind handover. If there is no such a target cell, the action fails, and the LDR performs the next action. The LDR checks whether the load difference between the current load and the basic congestion trigger threshold of each target cell for blink handover is larger than UL/DL Inter-freq cell load handover load space threshold (Both uplink and downlink condition must be all fulfilled). If the basic congestion trigger threshold is not set, the admission threshold of the cell is used. If the difference is not larger than the threshold, the action fails. The LDR performs the next action. If the LDR finds a target cell that meets the specified blind handover conditions, the LDR selects one UE to perform an inter-frequency blind handover to the cell according to the user integrate priority. For the selected UE, its UL/DL current bandwidth for DCH or GBR bandwidth for HSPA has to be less than the UL/DL Inter-freq cell load handover maximum bandwidth parameter (both the uplink and downlink conditions must be fulfilled). If there is more than one such UE, the one with the greatest bandwidth is taken. If the LDR cannot find such a UE, the action fails. The LDR performs the next action.
Key parameters
UL/DL Inter-freq cell load handover load space a Parameter ID: UL/DllnterFreqHoCellLoadSpaceThd a The default value of this parameter is 20 InterFreq HO code used ratio space a Parameter ID: LdrCodeUsedSpaceThd D The default value of this parameter is 13 UL/DL Inter-freq cell load handover maximum a Parameter ID: UL/DLINTERFREQHOBWTHD a The default value of this parameter is 200000 bandwidth threshold threshold
Pagel 32
4Pw
HUAWEI
UL/DL Inter-freq cell load handover load space threshold Parameter ID: UL/DLINTERFREQHOCELLLOADSPACETHD Value range: 0 to 100 % ,step:1% Content: The target cell can be a cell for inter-frequency blind handover only when the UL/DL load space is higher than the threshold. The UL/DL load space is the difference between the UL/DL basic congestion triggering threshold and the current UL/DL load of a target cell for blind handover.. The default value of this parameter is 20% Set this parameter through ADD CELLLDR / MOD CELLLDR InterFreq HO code used ratio space threshold Parameter ID: LdrCodeUsedSpaceThd Value range: 0 to 100%,step:1% Content: The target cell can be used for inter-frequency blind handover only when the DL Code used ratio space is higher than the threshold. The DL Code used ratio space is the difference of code used ratio between the source cell and the target cell. The default value of this parameter is 13% Set this parameter through ADD CELLLDR / LST CELLLDR / MOD CELLLDR UL/DL Inter-freq cell load handover maximum bandwidth Parameter ID: UL/DLINTERFREQHOBWTHD Value range: 0 to 400000 bps Content: During the inter-frequency load handover, the UE is selected as the target of inter-frequency load handover from the UE set where the bandwidth is less than this threshold. The default value of this parameter is 200000 Set this parameter through ADD CELLLDR / MOD CELLLDR
K X
LDR Actions
BE Rate Reduction a Target RABs Based on RAB integrate priority The data rate of BE service is larger than GBR Number of RABs to be selected is configurable
Page133
HUAWEI
BE rate reduction is implemented by reconfiguring the bandwidth. Bandwidth reconfiguration requires signaling interaction on the Uu interface. The LDR algorithm is implemented as follows: 1. Based on the integrate priority, the LDR sorts the RABs into a descending order. The top RABs related to the BE services (whose current rate is higher than its GBR configured by SET USERGBR command) are selected. If the integrate priorities of some RABs are identical, the RAB with the highest rate is selected. The number of RABs to select is determined by the UL/DL LDR-BE rate reduction RAB number parameter. 2. The bandwidth of the selected services is reduced to the specified rate. 3. If services can be selected, the action is successful. If services cannot be selected, the action fails. The LDR takes the next action. 4. The reconfiguration is completed as indicated by the RB RECONFIGURATION message on the Uu interface and through the RL RECONFIGURATION message on the Iub interface. 5. The BE rate reduction algorithm is controlled by the DCCC algorithm switch. BE rate reduction can be performed only when the DCCC algorithm is enabled.
Key parameters
* UL /DL LDR-BE rate reduction RAB number a Parameter ID: UL/DLLDRBERATEREDUCTIONRABNUM The default value of this parameter is 1
: ::'
::
'
'--:.:''--
::; - '
Page134
J# HUAWEI
UL /DL LDR-BE rate reduction RAB number Parameter ID: UL/DLLDRBERATEREDUCTIONRABNUM Value range: 1 to 10 Content: These parameters specify the number of RABs to select in a UL/DL LDR BE rate reduction. If the number of RABs that fulfil the criteria for BE rate reduction is smaller than the value of this parameter, then all the RABs that fulfil the criteria are selected. The default value of this parameter is 1 Set this parameter through ADD CELLLDR /MOD CELLLDR/ADD NODEBLDR/MOD NODEBLDR
LDR Actions
Uncontrolled Real-time service QoS Renegotiation
D Target RABs Based on RAB integrate priority Real-time services in the PS domain
Page135
I U HUAWEI
The load is reduced by adjusting the rate of the real-time services through uncontrolled realtime OoS renegotiation. Upon receipt of the message, the CN sends the RAB ASSIGNMENT REQUEST message to the RNC for RAB parameter reconfiguration. Based on this function, the RNC can adjust the rate of real-time services to reduce the load. The LDR algorithm is implemented as follows: 1. Based on the integrate priority, the LDR sorts the real-time services in the PS domain in descending order. The top services are selected for QoS renegotiation. 2. The LDR performs QoS renegotiation for the selected services. The GBR during service setup is the rate of the service after QoS renegotiation. 3. The RNC initiates the RAB Modification Request message to the CN for QoS renegotiation. 4. If the RNC cannot find a proper service for QoS renegotiation, the action fails. The LDR performs the next action.
Key parameters
UL/DL LDR un-ctrlRTQos re-nego RAB num a Parameter ID: UL/DLLDRPSRTQOSRENEGRABNUM D The default value of this parameter is 1
Paget 36
|f|| rlUAWEI
UL /DL LDR un-ctrl RT Qos re-nego RAB num Parameter ID: UL/DLLDRPSRTQOSRENEGRABNUM Value range: 1 to 10 Content: These parameters specify the number of RABs to select in a UL/DL LDR uncontrolled real-time QoS renegotiation. If the number of RABs that fulfil the criteria for uncontrolled real-time QoS renegotiation is smaller than the value of this parameter, then all the RABs that fulfil the criteria are selected. The default value of this parameter is 1 Set this parameter through ADD CELLLDR / MOD CELLLDR/ADD NODEBLDR/MOD NODEBLDR
LDR Actions
Inter-system Handover In the CS/PS Domain n Target user Based on the user integrate priority Handover Indicator
- "Handover to GSM should be performed" - "handover to GSM should not be performed"
GSM cell
WCDMA ce
Paget 37
HUAWEI
The 2G and 3G systems have different cell sizes and coverage modes. Therefore, blind handover across systems is not taken into account. The LDR is implemented in the downlink (e.g.) as follows: 1. Based on the integrate priority, the LDR sorts the UEs in descending order. The top CS/PS services are selected. 2. For the selected UEs, the LDR sends the load handover command to the inter-system handover module to ask the UEs to hand over to the 2G system. 3. The handover module decides to trigger inter-system handover, depending on the capability of the UE and the capability of the algorithm switch to support the compression mode. 4. This action is successful if any load handover UE is found. Otherwise, this action fails.
Key parameters
UL/DL CS should be ho user number n Parameter ID: UL/DLCSINTERRATSHOULDBEHOUENUM a The default value of this parameter is 3
# UL/DL
UL / DL CS should be ho user number Parameter ID: UL/DLCSINTERRATSHOULDBEHOUENUM Value range: 1 to 10 Content: These parameters specify the number of users to select in a UL/DL Inter-RAT Should Be Load Handover in the CS Domain. If the number of users that fulfil the criteria for Inter-RAT Should Be Load Handover in the CS Domain is smaller than the value of this parameter, then all the users that fulfil the criteria are selected. The default value of this parameter is 3 Set this parameter through ADD CELLLDR / MOD CELLLDR/ADD NODEBLDR/MOD NODEBLDR UL / DL CS should not be ho user number Parameter ID: UL/DLCSINTERRATSHOULDNOTBEHOUENUM Value range: 1 to 10 Content: These parameters specify the number of users to select in a UL/DL Inter-RAT Should Not Be Load Handover in the CS Domain. If the number of users that fulfil the criteria for Inter-RAT Should Not Be Load Handover in the CS Domain is smaller than the value of this parameter, then all the users that fulfil the criteria are selected. The default value of this parameter is 3 Set this parameter through ADD CELLLDR / MOD CELLLDR/ADD NODEBLDR/MOD NODEBLDR
Key parameters
UL/DL PS should be ho user number D Parameter ID: UL/DLPSINTERRATSHOULDBEHOUENUM a The default value of this parameter is 1
UL/DL
Page139
Hi H U A W E I
UL / DL PS should be ho user number Parameter ID: UL/DLPSINTERRATSHOULDBEHOUENUM Value range: 1 to 10 Content: These parameters specify the number of users to select in a UL/DL Inter-RAT Should Be Load Handover in the PS Domain. If the number of users that fulfil the criteria for Inter-RAT Should Be Load Handover in the PS Domain is smaller than the value of this parameter, then all the users that fulfil the criteria are selected. The default value of this parameter is 1 Set this parameter through ADD CELLLDR/ MOD CELLLDR/ADD NODEBLDR/MOD NODEBLDR UL / DL PS should not be ho user number Parameter ID: UL/DLPSINTERRATSHOULDNOTBEHOUENUM Value range: 1 to 10 Content: These parameters specify the number of users to select in a UL/DL Inter-RAT Should Not Be Load Handover in the PS Domain. If the number of users that fulfil the criteria for Inter-RAT Should Not Be Load Handover in the PS Domain is smaller than the value of this parameter, then all the users that fulfil the criteria are selected. The default value of this parameter is 1 Set this parameter through ADD CELLLDR/ MOD CELLLDR/ADD NODEBLDR/MOD NODEBLDR
LDR Actions
AMR Rate Reduction Target user AMR services and with the bit rate higher than the GBR Based on RAB integrate priority
Page140
HUAWEI
In the WCDMA system, voice services work in eight AMR modes. Each mode has its own rate. Therefore, mode control is functionally equal to rate control. The LDR algorithm is implemented as follows: 1. Based on the integrate priority, the LDR sorts the RABs in the descending order. The top UEs accessing the AMR services (conversational) and with the bit rate higher than the GBR are selected. 2. In uplink, the RNC sends the "Rate Control request" message through the lu-UP to the CN to adjust the AMR rate to the GBR. 3. In downlink, The RNC sends the TFC CONTROL command to the UE to adjust the AMR rate to the assured rate. 4. If the RNC cannot find a proper service for AMR rate reduction, the action fails. The LDR performs the next action.
Key parameters
# UL/DL LDR-AMR rate reduction RAB number D Parameter ID: UL/DLLDRAMRRATEREDUCTIONRABNUM D The default value of this parameter is 3
Page141
' W W
Hfi HUAWEI
UL/DL LDR-AMR rate reduction RAB number Parameter ID: UL/DLLDRAMRRATEREDUCTIONRABNUM Value range: 1 to 10 Content: These parameters specify the number of RABs to select in a UL/DL LDR AMR rate reduction. If the number of RABs that fulfil the criteria for AMR rate reduction is smaller than the value of this parameter, then all the RABs that fulfil the criteria are selected. The default value of this parameter is 3 Set this parameter through ADD CELLLDR / MOD CELLLDR
LDR Actions
Code Reshuffling n Reallocate code resources for candidate user
a Code Adjustment
*
Figure 1 Code treefee-orecase- wi'ru^v.-.y
EH
A
*
O rode occupied
?, / \
l & a & a n o p n n D D C D E
A A Aj Ai A A M fe i J in
\b
Q code not occupied
E 3
A AAA A / \ / \ / \ A
/ X
A
J33
\ K. A ofi
&
da
LO
i*rt3
u Kf5 a
ciS
ii
o selected subtree
C3 t i * a c
;_; i.'ofcrvtt!i.-i;-jp.i<
Page142
HUAWEI
The algorithm operates as follows: 1,Initialize the SF_Cur of the root node of subtrees to Cell LDR SF reserved threshold. 2,Traverse all the subtrees with this SF_Cur at the root node. Leaving the subtrees occupied by common channels and HSDPA channels out of account, take the subtrees in which the number of users is not larger than the value of the Max user number of code adjust parameter as candidates for code reshuffling. 3,Select a subtree from the candidates according to the setting of the LDR code priority indicator parameter. If this parameter is set to TRUE, select the subtree with the largest code number from the candidates. If this parameter is set to FALSE, select the subtree with the smallest number of users from the candidates. In the case that multiple subtrees have the same number of users, select the subtree with the largest code number.
4,Treat each user in the subtree as a new user and allocate code resources to each user. 5,Initiate the reconfiguration procedure for each user in the subtree and reconfigure the channel codes of the users to the newly allocated code resources. The reconfiguration procedure on the air interface is implemented through the PHYSICAL CHANNEL RECONFIGURATION message and that on the Iub interface through the RL RECONFIGURATION message.
Key parameters
Max user number of code adjust a Parameter ID: MAXUSERNUMCODEADJ D The default value of this parameter is 1
indicator
Page143
HUAWEI
Max user number of code adjust Parameter ID: MAXUSERNUMCODEADJ Value range: 1 to 3 Content: This parameter specifies the maximum number of users that can be selected whenever code reshuffling is performed. The default value of this parameter is 1 Set this parameter through ADD CELLLDR / MOD CELLLDR LDR code priority indicator Parameter ID: LdrCodePriUselnd Value range: True, False Content: This parameter specifies whether to select preferentially the subtree with a relatively large code number during subtree selection. Set this parameter through ADD CELLLDR / MOD CELLLDR
LDR Actions
MBMS Power Reduction
a Purpose The downlink power load can be reduced by lowering power on MBMS traffic channels
Page144
HUAWEI
The LDR algorithm is implemented as follows: 1. 2. Select all RABs with low priorities. The RNC initiates the reconfiguration procedure and resets the transmit power of MTCH (FACH) to the minimum value. The transmit power corresponds to the MBMS service. The reconfiguration procedure on the Iub interface is implemented through the COMMON TRANSPORT CHANNEL RECONFIGURATION REQUEST message.
3.
: Contents
2. Load Control Algorithms 2.1 PUC (Potential User Control) 2.2 LDB (Intra-Frequency Load Balancing) 2.3 CAC {Call Admission Controi) 2.4 IAC (Intelligent Admission Control) 2.5 LDR (Load Reshuffling) 2.6 OLC (Overload Control)
Page145
W W
HUAWEI
Page146
wMp
HUAWEI
After the UE access is granted, the power consumed by a single link is adjusted by the single link power control algorithm. The power varies with the mobility of the UE and the changes in the environment and the source rate. In some situations, the total power load of the cell may be higher than the target load. To ensure system stability, overload congestion must be handled.
k
__.Cell in overload congestion _ Overload congestion released
j
/
/-**m
u
1
tr V
time""
f
*-
If the current UL/DL load of an R99 cell is not lower than the UUDL OLC Trigger threshold for some hysteresis (defined by the DL State Trans Hysteresis threshold in DL; not configurable in UL), the cell works in overload congestion state and the related overload handling action is taken. If the current UL/DL load of the R99 cell is lower than the UL/DL OLC Release threshold for some hysteresis (defined by the DL State Trans Hysteresis threshold in DL; not configurable in UL), the cell comes back to the normal state. The HSPA cell has the same uplink decision criterion as the R99 cell. The load in the downlink, however, is the sum of load of the non-HSPA power (transmitted carrier power of all codes not used for HS-PDSCH or HS-SCCH transmission) and the GBP..
Key parameters
Cell LDC algorithm switch a Parameter ID: NBMLDCALGOSWITCH . UL_UU_OLC, DL_UU_OLC UL/DL OLC trigger
D
threshold
The default value of this parameter is 95% UL/DL OLC release threshold
Pagel48
ifcf HUAWEI
Cell LDC algorithm switch Parameter ID: NBMLDCALGOSWITCH Value range: OFF, ON Content: This parameter specifies the switch of UL/DL OLC. UL_UU_OLC: UL overload control algorithm DL_UU_OLC: DL overload control algorithm Set this parameter through ADD CELLALGOSWITCH / MOD CELLALGOSWITCH UL/DL OLC trigger threshold Parameter ID: UL/DLOLCTRIGTHD Value range: 0 to 1 0 0 % Content: If the UL load of the cell is not lower than the value of the UL OLC trigger threshold, the UL overload congestion control of the cell is activated. If the DL load of the cell is not lower than the value of the DL OLC trigger threshold, the DL overload congestion control of the cell is activated. Set this parameter through ADD CELLLDM / MOD CELLLDM UL/DL OLC release threshold
Parameter ID: UL/DLOLCRELTHD Value range: 0 to 1 0 0 % Content: If the UL load of the cell is lower than the value of the UL OLC release threshold, the UL overload congestion control of the cell is deactivated. If the DL load of the cell is lower than the value of the DL OLC release threshold, the DL overload congestion control of the cell is deactivated. Set this parameter through ADD CELLLDM / MOD CELLLDM
Turn on OLC algorithm switch Mark "current OLC state = un congested" Start OLC congestion indication report
Mark "current action = first OLC action" Clear the "selected" mark of all UE OLC actions Congestion state indicatio Send congestion release indication to MAC (downlink congestion)
1 I I
JLZ
=-c^purrerit OLC state = conge^rtetTr^z^TFControl ^<T Succeed?^ Y Mark "current action = successful action"
7
N
I
Sequence factions cannot be configured (current action is taken firstly)
Jl
-"" Succeed?
timer'
$
Releasing of
Succeed?
The general OLC procedure covers the following actions: TF control of BE services, channel switching of BE services, and release of RABs. The RNC takes periodical actions if overload congestion is detected. When the cell is overloaded, the RNC takes one of the following actions in each period (defined by the OLC period timer length parameter, e.g.3s) until the congestion is resolved: 1. TF control of BE service (only for DCH BE service) 2. Switching BE services to common channel 3. Choosing and releasing the RABs (for HSPA or DCH service) If the first action fails or the first action is completed but the cell is still in congestion, then the second action is taken.
Key parameters
OLC period timer length a Parameter ID: OLCPERIODTIMERLEN D The default value of this parameter is 3000 (ms)
Paget 50
HUAWEI
' >
Value range: 100 to 86400000 Content: This parameter specifies the period of overload control. The default value of this parameter is 3000 (ms) Set this parameter through SET LDCPERIOD
)h C^pC L^
<-\
^ K\
V*t
,^r
f***
.4 -<\
**
\^~^-+y
a**
....,!
OLC Action
TF Control n Target user Based on RAB integrate priority The RABs with the DCH BE services n Execution The RNC sends the "TF control indication" message to the MAC. MAC restricts the TFC selection : maximum TB number
- TFmax(N+1) = TFmax(N) x Ratelimitcoeff
Page151
iPI HUAWEI
Based on the RAB integrate priority, the OLC sorts the RABs into a descending order. The following RABs are selected: The RABs with the DCH BE services The RABs with the lowest integrate priority. The number of RABs selected is DL/UL OLC fast TF restrict RAB number. In downlink, The RNC sends the TF control indication message to the MAC. Each MAC of selected RABs will receive one TF control indication message and will restrict the TFC selection (from TFCS) of the BE services to reduce the data rate step by step.
MAC restricts the TFC selection in a way like that the maximum TB number is calculated with the formula: TFmax(N+1) = TFmax(N) x Ratelimitcoeff where: TFmax(O) is the maximum TB number of the BE service before the service is selected for TF control. TFmax(N+1) is the maximum TB number during time TO+RateRstrctTimerLen* (N) to TO+RateRstrctTimerLen* (N+1), where TO is the time MAC receiving the TF control indication message. RateRstrctTimerLen is a configurable parameter (DL TF rate restrict timer length). Ratelimitcoeff is a configurable parameter (DL OLC fast TF restrict data rate restrict coefficient). If the RNC cannot find an appropriate service for the TF control or the time for performing the TF control exceed the DL OLC fast TF restrict times parameter, the action fails. The OLC performs the next action. If the congestion is released, the RNC sends the congestion release indication to the MAC. At the same time, the rate recovery timer (whose length is defined by DL OLC fast TF restrict data rate recover timer length) is started. When this timer is expired, the MAC increases the data rate step by step. MAC restricts the TFC selection by calculating the maximum TB number with the formula: TFmax(N+1) = TFmax(N) x RateRecoverCoeff where: TFmax(O) is the maximum TB number of the BE service before congestion release indication is received. TFmax(N+1) is the maximum TB number during time T1+ RateRecoverTimerLen * (N) to T1+RateRecoverTimerLen* (N+1), where T1 is the time MAC receiving congestion release indication message. RateRecoverTimerLen is a configurable parameter (DL TF rate recover timer length). RateRecoverCoeff is a configurable parameter (DL TF rate recover coefficient).
In the Uplink For a UE accessing the DCH service, the RNC, in compliance with the 3GPP TS25.331, restricts the TFC of the UE by sending the TRANSPORT FORMAT COMBINATION CONTROL message to the UE , UE does not have any response if the procedure can be performed successfully. The number of RABs to select is defined by the UL OLC fast TF restrict RAB number parameter.
UE UTRAN
The TRANSPORT FORMAT COMBINATION CONTROL message contains the following lEs: Transport Format Combination Set Identity: defines the available TFC that the UE can select, that is, the restricted TFC sub-set. It is always the two TFCs corresponding to the lowest data rate. TFC Control duration: defines the period in multiples of 10 ms frames for which the restricted TFC sub-set is to be applied. It is set to a random value from the range of 10 ms to 5120 ms, so as to avoid data rate upsizing at the same time. After the TFC control duration is due, UE can apply any TFC of TFCS before the TF control. Each UE of selected RABs will receive the TRANSPORT FORMAT COMBINATION CONTROL message. How many times TF control is performed is defined by the UL OLC fast TF restrict times parameter. If the RNC cannot find an appropriate service, the OLC performs the next action.
<
^
"'
OLC Action e ^
TF Control example
>..; \
9*336 *~
\i
4*33S
Pagel54
HUAWEI
Before point A, the cell is not in OLC state. The downlink data transfer rate is 384 kbit/s, the corresponding TF is 12 x 336, and TFS is {12 x 336, 8 x 336,4 x 336, 2 x 336, 1 x 336, 0 x 336}.336 is the TB size, 320 payload + 16 MAC head At point A, the cell enters OLC state. The RNC selects this RAB to do fast TF restriction. MAC restricts the TFC selection during time between point A and point B by calculating the maximum TB number as follows: TFmax(1) = TFmax(O) x Ratelimitcoeff = 12 x 0.68 = 8.16 Match 8.16 and the TFS. Therefore, the maximum TB number is 8. At point B, MAC performs further TFC restriction by calculating maximum TB number as follows: TFmax(2) = TFmax(1) x Ratelimitcoeff = 8 x 0.68 = 5.44 Match 5.44 and the TFS. Then, the maximum TB number is 4. At point C and point D, similar process is followed.
Key parameters
UL/DL OLC fast TF restrict RAB number a Parameter ID: U17DL0LCFTFRSTRCTRABNUM The default value of this parameter is 3 UL/DL OLC fast TF restrict times a Parameter ID: UL/DLOLCFTFRSTRCTTIMES The default value of this parameter is 3
Page155
j W
HUAWEI
UL/DL OLC fast TF restrict RAB number Parameter ID: UL/DLOLCFTFRSTRCTRABNUM Value range: Oto 10 Content: These parameters specify the maximum number of RABs selected in a fast TF restriction of UL/DL OLC. If the number of RABs that fulfil the criteria for TF control is smaller than the value of this parameter, then all the RABs that fulfil the criteria are selected. The default value of this parameter is 3 Set this parameter through ADD CELLOLC / MOD CELLOLC UL/DL OLC fast TF restrict times Parameter ID: UL/DLOLCFTFRSTRCTTIMES Value range: Oto 100 Content: These parameters specify the times of UL/DL OLC fast TF restrictions that are executed. The default value of this parameter is 3 Set this parameter through ADD CELLOLC / MOD CELLOLC
Key parameters
* DL TF rate restrict coefficient a Parameter ID: RateRstrctCoef D The default value of this parameter is 68% DL TF rate restrict timer length
D Parameter ID: RateRstrctTimerLen n The default value of this parameter is 3000 (ms)
Page156
| P t | HUAWEI
DL TF rate restrict coefficient Parameter ID: RateRstrctCoef Value range: 1 to 99 % Content: This parameter specifies the data rate restriction coefficient in the fast TF restriction. The smaller the parameter is, the more effective the TF restriction is. After receiving the TF control indication, the MAC obtains the maximum TF format with the formula TFmax' = TFmax x Ratelimitcoeff. The default value of this parameter is 68 % Set this parameter through ADD CELLOLC / MOD CELLOLC DL TF rate restrict timer length Parameter ID: RateRstrctTimerLen Value range: 1 to 65535 ms Content: This parameter specifies the length of the data rate restriction timer in the fast TF restriction. The smaller the value of this parameter is, the more effective the TF restriction is. The default value of this parameter is 3000 ms Set this parameter through ADD CELLOLC / MOD CELLOLC
Key parameters
DL TF rate recover timer length n Parameter ID: RateRecoverTimerLen D The default value of this parameter is 5000 (ms) DL TF rate recover coefficient
Pagel 57
|1> HUAWEI
DL TF rate recover timer length Parameter ID: RateRecoverTimerLen Value range: 1 to 65535 ms Content: This parameter specifies the length of the data rate recovery timer. The smaller the value of this parameter is, the faster the BE traffic rate increases after the congestion is resolved. The default value of this parameter is 5000 ms Set this parameter through ADD CELLOLC / MOD CELLOLC DL TF rate recover coefficient Parameter ID: RecoverCoef Value range; 100 to 200 % Content: This parameter specifies the data rate recovery coefficient in the fast TF restriction. The larger the parameter is, the larger the TF recover effect. After receiving congestion release indication, the MAC obtains the maximum TF format with the formula TFmax' = TFmax x RateRecoverCoeff. The default value of this parameter is 130% Set this parameter through ADD CELLOLC / MOD CELLOLC
OLC Action
Switching BE Services to Common Channel
p Target user Based on the user integrate priority The users with the DCH or HSDPA BE services in PS n Execution The RNC sends "RB Reconfiguration" message to UE UE make a response by "RB Reconfiguration Complete" ' .
--- ;-
Page158
#l# HUAWEI
The OLC algorithm for switching BE services to common channel operates as follows: Based on the user integrate priority, the OLC sorts all UEs that only have PS services including HSPA and DCH services (except UEs having also a streaming bearer) into a descending order. The top N UEs are selected. The number of selected UEs is equal to Transfer Common Channel user number. If UEs cannot be selected, the action fails. The OLC performs the next action. The selected UEs are switched to common channel.
Key parameters
Transfer Common Channel User number a Parameter ID: TransCchUserNum D The default value of this parameter is 1
Page159
W W # 1HUAWEI
Transfer Common Channel User number Parameter ID: TransCchUserNum Value range: 1 to 10 Content: This parameter specifies the transfer common channel user number The default value of this parameter is 1 Set this parameter through ADD CELLOLC / MOD CELLOLC
OLC Action
Release of Some RABs D Target user
Based on the RAB integrate priority DCH services RAB n Execution The RNC sends "IU Release Request" message to CN The RNC sends "RRC Connection Release" message to UE
Page160
OLC Algorithm for the Release of Some RABs in the Uplink: The OLC algorithm for the release of some RABs in the uplink operates as follows: Based on the integrate priority, the OLC sorts all RABs including HSUPA and DCH services into a descending order. The top RABs selected. If the integrate priorities of some RABs are identical, the RAB with higher rate (current rate for DCH RAB and GBR for HSUPA RAB) in the uplink is selected. The number of selected RABs is equal to UL OLC traff release RAB number. The selected RABs are released directly. OLC Algorithm for the Release of Some RABs in the Downlink The OLC algorithm for the release of some RABs in the downlink operates as follows: Based on the integrate priority, the OLC sorts all RABs into a descending order. The top-priority RABs are selected. If the integrate priorities of some RABs are identical, the RAB with higher rate (current rate) The number of selected RABs is equal to DL OLC traff release RAB number. The selected RABs are directly released.
Key parameters
UL/DL OLC traff release RAB number u Parameter ID: UL/DLOLCTRAFFRELRABNUM D The default value of this parameter is 0
Page161
Pw
HUAWEI
UL/DL OLC traff release RAB number Parameter ID: UL/DLOLCTRAFFRELRABNUM Value range: Oto 10 Content: Either parameter specifies the number of RABs released in a UL or DL OLC release action. If the number of RABs that fulfil the criteria for release is smaller than the value of this parameter, then all the RABs that fulfil the criteria are selected. The default value of this parameter is 0 Set this parameter through ADD CELLOLC / MOD CELLOLC
) Summary
Load Control Algorithms PUC (Potential User Control) LDB (Intra-Frequency Load Balancing) CAC (Call Admission Control) IAC (Intelligent Admission Control) LDR (Load Reshuffling) OLC (Overload Control)
'
:: :- . ..
Page162
Thank You
www.huawei.com
Paget 63
| P | HUAWEI
163