Documente Academic
Documente Profesional
Documente Cultură
Road Construction and Maintenance Variable Factors Hot Mix Mixture Specifications Road Recycling Industrial Usage
Variable factors
The exact make-up of a road will depend on several variable factors such as the weight and volume of traffic it has been designed to carry, local climatic conditions and the availability of mineral aggregates. In most cases bitumen will be needed for its properties of waterproofing and durability and as the cheapest adhesive generally available. A minor secondary road may use bitumen only for its top two courses, at the rate of 7 tonnes per kilometre. A highway engineer may call for bitumen to be applied to three courses, with tack coats in between, because of the mixture's superior load bearing properties. In this case bitumen consumption can amount to 1000 tonnes per kilometre. The bitumen percentage in an aggregate/bitumen mixture is usually between 4-8%. General Road Construction and Maintenance Applications Paving Cutbacks Emulsions Modified Grades bitumens Low High Example of Use 50 170 320 600 viscosity viscosity Cutback Manufacture Emulsion Manufacture Hot-mix asphalt Spray Seals Tack Coat This table defines some typical road construction and maintenance applications.
Hot Mix
The mixing of aggregates and bitumen to produce asphalt may take place at a purpose-built plant located away from the road construction site or it may be done at the site itself. Controlled amounts of aggregates, which have been carefully graded to meet the specification, are dried and heated before being mixed with a measured quantity of hot bitumen. All this takes place in a purpose-built plant. The hot mixture, at a temperature of up to 160C, is carried to the construction site and laid while still hot. This describes in simple terms a process in which skill and experience are combined with computerised control systems to carry out a complex series of operations. Various sizes of aggregates dry out, gain and retain heat at different rates. Their temperature must be controlled so that the bitumen does not cool when it is mixed with the aggregates. The supply of aggregates is continuously weighed by scales linked to the pump metering the supply of bitumen, so that a constant ratio of aggregate to bitumen is maintained. The mixing time should be no longer than is necessary for the uniform distribution of the bitumen as a coating for the aggregate particles, otherwise the bitumen film will harden as it is exposed to air. If the mixing process takes too long the durability of the mixture will be impaired. To provide consistent high quality mixtures, continuous operation of the plant is required which in turn means that all parts of the operation must be integrated so there are no hold-ups as the drying, screening, mixing, transporting and laying processes are carried out. Bitumen supplies are ordered daily to meet the production schedules based on the road gangs' programmes for the following day. As bitumen storage capacity is usually limited, delivery has to be made on a when required basis, often within thirty minutes of a target time based on the moment when the aggregates have been heated to the right temperature for mixing with bitumen. Any delay means that expensive fuel is wasted in keeping the aggregate at the right temperature. This precision in delivery calls for a high degree of commitment on the part of the supplier in terms of capital equipment, logistics and technical expertise. With cutbacks and bitumen emulsions, lower aggregate (stone) temperatures (30-100C) can be used: mixing may be carried out on site or by using mobile mixing plants. This is one of the significant advantages of using these bitumens when the design of the road allows them to be specified.
Mixture Specifications
Asphalts have been classified into a number of different types, which may be simply stated as: Asphaltic Concrete: a dense, continuously graded mixture of coarse and fine aggregates, mineral filler and bitumen produced hot in a mixing plant. It is delivered, spread and compacted while hot. Bituminous Macadam: a road with a graded aggregate and bituminous coating, in which the mechanical interlock of the aggregate particles contributes significantly to its strength. Open-graded Asphalt: an asphaltic mix using aggregates containing only small amounts of fine material and providing a high percentage of air voids. Stone Mastic Asphalt: a gap-graded wearing course mix with a high proportion of coarse aggregate content which interlocks to form a stone-onstone skeleton to resist permanent deformation. The mix is filled with a mastic of bitumen and filler. Tack coat: a thin layer of emulsified or cutback bitumen that bonds a layer of road to the layer beneath. Current practice is to favour the more modem bitumen emulsions in place of cutbacks. Surface treatments: including dressings and coats, involve spraying a coating of bitumen onto the surface of a wearing course. It can be sprayed as an emulsion, a cutback or a paving grade bitumen. Either a single or double coating of fine aggregates or stone chippings is applied. These treatments are applied to renovate and waterproof old roads that require maintenance. An example of such a treatment is a fog seal which is a coat of bitumen emulsion applied to an existing surface to seal cracks as a maintenance treatment. Bituminous Slurry Surfacing: an important maintenance treatment for the surface in which a mixture of fine aggregates and filler and emulsified bitumen is applied to a structurally sound road surface for minor shape corrections and to improve skid resistance. It has the advantage that it can be applied rapidly at a relatively low cost by a truck-mounted mixing plant.
Road Recycling
The techniques of road recycling reclaim the materials used to build roads. They offer benefits in terms of reduced demands for aggregates and energy. The layers of road surface are ripped up, crushed and reprocessed with varying proportions of fresh aggregate, new bitumen or emulsions and, if necessary, a recycling agent. The process may be carried out on site (in situ), or the reclaimed material can be transported to and from the site to be mixed in a dedicated, static plant.
Industrial Usage
The use of bitumen in industry accounts for less, than 20% of world bitumen production. It is nevertheless important to those manufacturers and engineers who rely on its particular properties as an economical binder and protector. In many parts of the world it is used extensively to waterproof the roofs of houses, often in the form of shingles which are strips of
felt first impregnated with bitumen and then covered on both sides with harder bitumen and a coating of mineral granules. A similar construction technique involves sheets of bitumensaturated felt laid onto a flat roof with layers of bitumen below, between and above them. In more complex roofing projects, bitumen is to be found holding in place a protective coating of chippings on the cantilevered roof of a sports stadium. By contrast, bitumen is also used in dampproofing and floor composition tiles. Other materials, particularly felts and papers, are impregnated with bitumen to improve their performance as regards insulation. Packaging papers, printing inks, linoleum, sound deadening felts hidden inside car bodies and the undersealing compounds beneath them, electrical insulating compounds and battery boxes are some of the hundreds of industrial and domestic products likely to contain bitumen.