Documente Academic
Documente Profesional
Documente Cultură
Introduction
In this practice Packet Tracer Skills Exam, you will: finish designing the IP addressing scheme implement the addressing in the network to meet the requirements configure Frame Relay and EIGRP to enable communication with the rest of the network configure a backup link in case the Frame Relay network becomes unavailable implement a security policy using access control lists to filter traffic
Addressing Table
Device Interface Fa0/0.1 Fa0/0.10 BR2 Fa0/0.20 Fa0/1 S0/0/0.101 Fa0/0 Edge3 Fa0/1 S0/0/0.201 Fa0/0 ISP Fa0/1 S1 S2 S3 H1 H2 Server VLAN1 VLAN1 VLAN1 NIC NIC NIC 172.16.1.222 172.17.1.6 255.255.255.248 172.17.1.1 172.16.1.227 172.17.1.2 255.255.255.248 172.17.1.1 10.10.10.5 255.255.255.252 n/a 10.10.10.2 172.31.1.1 172.17.1.1 10.10.10.6 172.31.1.2 10.10.10.1 255.255.255.252 255.255.255.252 255.255.255.248 255.255.255.252 255.255.255.252 255.255.255.252 Address Subnet Mask Default Gateway n/a n/a n/a n/a n/a n/a n/a n/a n/a
NOTE: To aid in configuring, verifying and troubleshooting the devices, use a printed version of these instructions to fill in the missing address information in the table during Step 2.
All contents are Copyright 19922010 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 1 of 4
CCNA Discovery Designing and Supporting Computer Networks DCompNtwk Frame Relay/EIGRP PT Practice SBA
d. Assign the last (highest) address in this subnet to H1. e. Subnet the remaining address space to provide 30 host addresses for the BR2 VLAN 20 while wasting the least amount of space. f. Assign the first available subnet to the BR2 VLAN 20.
g. Assign the first (lowest) address in this subnet to the Fa0/0.20 subinterface on BR2. h. Subnet the remaining address space to provide 6 host addresses for the BR2 VLAN 1 while wasting the least amount of space. i. j. k. Assign the first available subnet to the BR2 VLAN 1. Assign the first (lowest) address in this subnet to the Fa0/0.1 subinterface on BR2. Assign the second address in this subnet to the VLAN 1 interface on S1.
Step 3: Configure S1 with IP Address, VLANs and as the STP Root Bridge.
NOTE: S2 is already configured. You do not have access to S2. On S1, you will receive a Domain Mismatch message every 30 seconds until S1 is correctly configured. a. Configure the S1 VLAN interface with the correct IP addressing as determined in Step 1 b. Configure the default gateway. c. Establish an 802.1q trunk with BR2 and with S2. After STP converges, S1 should be able to ping both BR2 and S2.
d. S1 should be configured as a VTP server for the discovery domain. Set the VTP password to cisco. S2 is already configured as a client for this domain. e. Create and name two VLANs on the VTP server. Names are case-sensitive: f. VLAN 10, Name: Staff VLAN 20, Name: Guest
g. Use a priority of 4096 to set S1 as the STP root for all VLANs.
All contents are Copyright 19922010 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 2 of 4
CCNA Discovery Designing and Supporting Computer Networks DCompNtwk Frame Relay/EIGRP PT Practice SBA
b. Verify that Frame Relay is operational between BR2 and Edge3. BR2 should be able to ping the directly-connected interface of Edge3.
b. Verify that BR2 is now neighbors with Edge3. H1 should be able to ping Discovery Server.
d. Use the "Add Simple PDU" tool to verify that H2 can ping Discovery Server.
b. Verify that the backup link is operational by temporarily shutting down the Serial 0/0/0 interface. c. H1 and H2 should still be able to ping Discovery Server after the network converges.
d. Restore the Serial 0/0/0 interface and verify the Frame Relay network is operational again.
All contents are Copyright 19922010 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 3 of 4
CCNA Discovery Designing and Supporting Computer Networks DCompNtwk Frame Relay/EIGRP PT Practice SBA
c.
All other traffic is allowed. The access list should still be in effect when the backup link is active.
b. Use the "Add Simple PDU" tool to verify that H2 cannot ping Discovery Server or Edge3. Take the BR2 Frame Relay link down and verify that the same results occur through the backup link.
All contents are Copyright 19922010 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 4 of 4