Documente Academic
Documente Profesional
Documente Cultură
to
MINI-32
The whole PIC32 development board fitted on DIP40 containing powerful PIC32MX534F064H microcontroller. Its the first ever PIC32 chip on DIP40 socket, pin compatible with PIC16F887 and PIC18(L)F45K20 microcontrollers!
The Microchip, Atmel, NXP and CYPRESS name, logo and products names are trademarks of Microchip, Atmel, NXP and CYPRESS Inc. in the U.S.A and other countries.
Table of Contents
Introduction to MINI-32 Key features System Specification 1. Programming with bootloader step 1 Connecting MINI-32 step 2 Browsing for .hex file step 3 Select .hex file step 4 .hex file uploading step 5 Finish upload 2. Schematic 3. Dimensions 4. Pinout 4 4 5 6 6 7 7 8 9 10 11 12
Page 3
Introduction to MINI-32
Key features
01 Reset button 02 DATA LED (connected on RD6) 02 01 03 04 05 07 06 03 STAT LED (connected on RG6) 04 POWER supply LED 05 Microcontroller PIC32MX534F064H 06 Quartz-crystal oscillator 07 USB MINIB connector
Miniature and powerful development tool designed to work as stand alone device or as MCU in DIP40 socket. MINI-32 comes with preinstalled bootloader so it is not necessary to have external programmer. If there is need for external programmer (mikroProg) attach it to MINI-32 via pads marked with RB6 (PGC), RB7 (PGD) and MCLR.
Page 4
System Specification
power supply 3.3V via pads or 5V via USB
power consumption depends on MCU state (max current into 3.3V pad is 300mA) board dimensions 50.80 x 17.78mm (2 x 0.70)
Page 5
Figure 1-1: mikroBootloader USB HID 01 Connect MINI-32 board with a PC via USB cable and USB icon will turn red 02 Whitin 5s click on Connect button
Page 6
MINI-32
01 01
01 Figure 1-2: Browse for HEX 01 Click on Browse for HEX button Figure 1-3: Selecting HEX 01 Select .hex file via open window 02 Click on Open button
Page 7
MINI-32
MINI-32
01
01 Figure 1-4: Begin uploading 01 To start .hex file uploading click on Begin uploading button Figure 1-5: Progress bar 01 You can monitor .hex file uploading via progress bar
Page 8
01
Page 9
2. Schematic
VCC-3.3 VCC-3.3
CN2 RB8 RD4 RD5 RB9 RD11 RB0 RB1 RB4 RB5 MCLR
VCC-3.3
VCC-3.3
C1 100nF
C2 100nF
VOUT E2 10uF
REG1 3 2 1
VCC-USB
VIN E1 10uF
E3 10uF
VCC-3.3
VCC-3.3
R1 10K RESET
RE3 RE2 RE1 RE0 RF1 RF0 VDD VCAP RD7 RD6 RD5 RD4 RD3 RD2
RE4
RD1
LD1 R5 2K2
RE5
SOSCO
MCLR
T1
SOSCI SOSCO
VCC-3.3
C6 22pF
RB6 RB7 AVDD AVSS RB8 RB9 RB10 RB11 VSS VDD RB12 RB13 RB14 RB15 RF4
RF5
X2 32.768kHz
C5 22pF
RE6 RE7 RG6 RG7 RG8 MCLR RG9 VSS VDD RB5 RB4 RB3 RB2 RB1
RB0
SOSCI RD0 RD11 RD10 RD9 RD8 VSS OSC2 PIC32MX534F064H OSC1 VDD D+/RG2 D-/RG3 VUSB VBUS USB-ID
VCC-3.3
C8 100nF
USBDP USBDM
VCC-3.3
C3 100nF
OSC1 OSC2
USB-DET
CN3
R2 100
GND 5 ID 4 D+ 3 D- 2 VBUS 1
C9 22pF
X1 8MHz
C7 22pF
RE7 RE6 RE5 RE4 RF4 RF5 RG8 RG7 RE3 RE2
R7 100K
USB MINIB
3. Dimensions
50.80mm (2")
17.78mm (0.70")
2.54mm (0.10")
Figure 3-1: Board dimensions
Page 11
4. Pinout
Pin functions AN5 Analog I/O AN4 AN1/VREFAN0/VREF+ INT4 AN9 Digital I/O AN8/U5RX 3.3V Power supply GND CAN C1TX C1RX AN15 INT0 SCK2 Digital I/O Analog Lines MCLR RB5 RB4 RB1 RB0 RD11 RB9 RD5 RD4 RB8 3.3V GND RF1 RF0 RB14 RB15 RD0 RG6 RE0 RE1 Interrupt Lines SPI Lines
Page 12
RB7 RB6 RD3 RD2 RD1 RD10 RD9 RD8 3.3V GND RE7 RE6 RE5 RE4 RF4 RF5 RG8 RG7 RE3 RE2 I2C Lines
PGED2 PGEC2
SCL3/SDO3/U1TX SDA3/SDI3/U1RX SCK3/U1RTS INT3 INT2 RTCC/INT1 3.3V Power supply GND
SPI/UART
Digital I/O
AN14/U5TX
U2RX U2TX
CAN lines
Notes:
Page 13
Notes:
Page 14
DISCLAIMER All the products owned by MikroElektronika are protected by copyright law and international copyright treaty. Therefore, this manual is to be treated as any other copyright material. No part of this manual, including product and software described herein, may be reproduced, stored in a retrieval system, translated or transmitted in any form or by any means, without the prior written permission of MikroElektronika. The manual PDF edition can be printed for private or local use, but not for distribution. Any modification of this manual is prohibited. MikroElektronika provides this manual as is without warranty of any kind, either expressed or implied, including, but not limited to, the implied warranties or conditions of merchantability or fitness for a particular purpose. MikroElektronika shall assume no responsibility or liability for any errors, omissions and inaccuracies that may appear in this manual. In no event shall MikroElektronika, its directors, officers, employees or distributors be liable for any indirect, specific, incidental or consequential damages (including damages for loss of business profits and business information, business interruption or any other pecuniary loss) arising out of the use of this manual or product, even if MikroElektronika has been advised of the possibility of such damages. MikroElektronika reserves the right to change information contained in this manual at any time without prior notice, if necessary. HIGH RISK ACTIVITIES The products of MikroElektronika are not fault tolerant nor designed, manufactured or intended for use or resale as on line control equipment in hazardous environments requiring fail safe performance, such as in the operation of nuclear facilities, aircraft navigation or communication systems, air traffic control, direct life support machines or weapons systems in which the failure of Software could lead directly to death, personal injury or severe physical or environmental damage (High Risk Activities). MikroElektronika and its suppliers specifically disclaim any expressed or implied warranty of fitness for High Risk Activities. TRADEMARKS The Mikroelektronika name and logo, the Mikroelektronika logo, mikroC, mikroC PRO, mikroBasic, mikroBasic PRO, mikroPascal, mikroPascal PRO, AVRflash, PICflash, dsPICprog, 18FJprog, PSOCprog, AVRprog, 8051prog, ARMflash, EasyPIC5, EasyPIC6, BigPIC5, BigPIC6, dsPIC PRO4, Easy8051B, EasyARM, EasyAVR5, EasyAVR6, BigAVR2, EasydsPIC4A, EasyPSoC4, EasyVR Stamp LV18FJ, LV24-33A, LV32MX, PIC32MX4 MultiMedia Board, PICPLC16, PICPLC8 PICPLC4, SmartGSM/GPRS, UNI-DS are trademarks of Mikroelektronika. All other trademarks mentioned herein are property of their respective companies. All other product and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are only used for identification or explanation and to the owners benefit, with no intent to infringe. Mikroelektronika, 2011, All Rights Reserved.
Page 15
MINI-32
If you want to learn more about our products, please visit our website at www.mikroe.com If you are experiencing some problems with any of our products or just need additional information, please place your ticket at www.mikroe.com/en/support If you have any questions, comments or business proposals, do not hesitate to contact us at office@mikroe.com