Documente Academic
Documente Profesional
Documente Cultură
OUTLINE
Preliminary Section: y Contact Information, Preliminary Matters, Specifications, LCD Overview, General Troubleshooting Steps, Signal Distribution, Disassembly Instructions and Voltages Disassembly Section: Removal of Circuit Boards Troubleshooting Section: Board Operation Troubleshooting of : Switch Mode Power Supply Ballast (Backlight Driver) Main Board Ft Control Board
Key Board
Speakers
At the end of this Section the Technician should be able to Identify the Circuit Boards f S f C and have the ability and knowledge necessary to safely remove and replace any Circuit Board or Assembly.
CAUTION
To avoid personal injury, disconnect the power before servicing this product. If electrical power is required for g purposes, disconnect the p , power immediately after p y performing the necessary checks. Also be g y diagnosis or test p p aware that many household products present a weight hazard. At least two people should be involved in the installation or servicing of such devices. Failure to consider the weight of an product could result in physical injury.
ESD Notice
Todays sophisticated electronics are electrostatic discharge (ESD) sensitive. ESD can weaken or damage the electronics in a manner that renders them inoperative or reduces the time until their next failure. Connect an ESD wrist strap to a ground connection point or unpainted metal in the product. Alternatively, you can touch your finger repeatedly to a ground connection point or unpainted metal in the product. Before removing a replacement part from its package, touch the anti static bag to a ground connection point or anti-static unpainted metal in the product. Handle the electronic control assembly by its edges only. When repackaging a failed electronic control assembly in an anti-static bag, observe these same precautions.
Regulatory Information l f
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to g provide reasonable p protection against harmful g Part 15 of the FCC Rules. These limits are designed to p interference when the equipment is operated in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is reception, on, encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna; Increase the separation between the equipment and the receiver; Connect the equipment to an outlet on a different circuit than that to which the receiver is connected; or consult the dealer or an experienced radio/TV technician for help.
LG Contact Information
Customer Service (and Part Sales) Technical S T h i l Support (and Part Sales) ( dP S l ) USA Website (GSFS) Customer Service Website Knowledgebase Website LG Web Training LG CS L Learning A d i Academy (800) 243-0000 (800) 84 847-7597 9
http://136.166.4.200
Training Manuals, Schematics with Navigational Bookmarks, Start-Up Sequence, Owners Guides, Interconnect Diagrams, Dimensions, Connector IDs, Product Pictures and Features.
42SL80, 47LG90, 47LH85, 42LE5500, 42LX6500 (3D), 47LX9500 (3D), 55LX6500 (3D) 42PG20, 42PJ350, 42PQ20, 42PQ30, 50PG20, 50PJ350, 50PK250, 50PK750, 50PS80, 50PK950, PLASMA: 50PS60, 60PK750, 60PK950, 60PS11, 60PS60, 60PS80 32LD350, 32LG40, 32LH30, 37LH55, 42LG60, 42LG70, 42LH20, 42LH40, 42LH50, 42LH90, LCD-DV: 32LD350 32LG40 32LH30 37LH55 42LG60 42LG70 42LH20 42LH40 42LH50 42LH90
Also available on the Plasma Page: PDP Panel Alignment Handbook, Plasma Control Board ROM Update (Jig required)
Published July 2010 by LG Technical Support and Training LG El Electronics Al b i Alabama, I Inc. 201 James Record Road, Huntsville, AL, 35813.
This section of the manual will discuss the specifications of the 32LD350 LCD Direct View Display
9 November LCD TV 32LD350
Basic Specifications
Key TV Features High Definition Resolution 70 000 1 D 70,000:1 Dynamic C t t R ti i Contrast Ratio Picture Wizard II (Easy Picture Calibration) Smart Energy Saving gy g AV Mode (Cinema, Sports, Game) Clear Voice II ISFccc Ready 24P Real Cinema 2 HDMI 1.3 Inputs SIMPLINK Connectivity C ti it Dolby Digital 5.1 Decoder Infinite Sound
10 November LCD TV 32LD350
Clear Voice Clearer dialogue sound Automatically enhances and amplifies the sound of the human voice frequency range to provide high-quality dialogue when background noise swells swells.
1 1
12
BOTTOM PORTION
p/n AKB72915206
13
To access the Service Menu. 1) You must have either Service Remote. ) p/n 105-201M or p/n MKJ39170828 2) Press In-Start 3) A Password screen appears. 4) Enter the Password. )
Note: A Password is required to enter the Se ce e u Service Menu. Enter; 0000 te ; Note: If 0000 does not work use 0413.
105-201M
MKJ39170828
14
Side In/Out
Component Inputs
15
2) Copy new software (xxx.epk) to "LG_DTV" folder. Make sure to have correct software file. 3) With TV turned on insert USB flash drive. on, drive 4) You can see the message TV Software Upgrade (See figure to right) 5) Cursor left and highlight "START" Button and push Enter button using the remote control. 6) You can see the download progress Bar. 7) Do not unplug until unit has automatically restarted. 8) When download is completed, you will see COMPLETE COMPLETE. 9) Your TV will be restarted automatically.
* CAUTION: Do not remove AC power or the USB Flash Drive. Do not turn off Power, during the upgrade process. Software Files are available from the GSFS or GCSC web sites.
16
17
Host Diagnostics
Host Information Model Name : 32LD350-UB (Liquid Crystal Display) Memory FLASH : 16384 KB DRAM : 131072 KB NVM : 64 KB Host Release Version Firmware Version(MP) : 3.05.00(0.1.58.22) Micom Version : 3.02 Compile Date & Time : 20100126 & 08:56:56 Compile User : jh.jung
Channel Frequency
Channel Selected
Parental Control : Channel is not blocked DVI/HDMI Status Cant display this information now
Software Version
FAT Status (Main) Center Frequency : 663.00 MHz Program Clock Reference (Locked or No) PCR lock : Locked Modulation mode : QAM 256 Carrier lock status : Locked SNR : 36 dB Signal level : 99 dBmV Channel Type (8VSB, QAM 64, 256) Channel (Locked or No) Channel Signal Level (Above 80dBmV good) 8VSB (Above 20 is good) QAM 64 (Above 24 is good) QAM 256 (Above 30 is good)
Half Page
CH
Move Page
Exit
18
November 2010
32LD350
LCD-DV
19
6) Highlight Start then press Select key. begins. Select key Writing begins
20
7-7/8" 200mm
6-5/16" 160mm
3-15/16" 100mm
Center
10" 254mm Remove 4 screws to remove stand for wall mount 2-3/16" 55.56mm
11 1/8" 281.78mm
15-3/4" 400mm
8-1/8" 205.74mm
21
November 2010
32LD350
LCD-DV
DISASSEMBLY SECTION
Disassembly: This section of the manual will discuss Disassembly, Layout (Circuit B d Id tifi ti ) f th (Ci it Board Identification) of the 32LD350 LCD Di t Vi Direct View T l i i Television. Upon completion of this section the Technician will have a better understanding of the disassembly procedures, the layout of the printed circuit boards and be able to identify each board.
22
Remove the 20 screws indicated. Pay attention to the i th size and t d type of screw as there are many different types.
Stand Base is Glass Handle with Care The Stand does not have to be removed before removing the back.
23
Board Layout
Clips hold front frame in place, use caution. Suggest adding screw while servicing.
Ballast
LVDS Cable
IR/LED Board
24
TFT PANEL
AUSWLJR, AUSDLFR, p/n: EAJ60890301 AUSDLJR, AUSDLUR, CUSDLH
Panel Interface
If the Panel is replaced, reset the UTTTime. Service Menu, System Item 18
Ballast
P203 P201
CN1
POWER SUPPLY
SMPS Used in the 32LD350: EAY60868901 32LD350 AUSWLJR or AUSDLFR or AUSDLUR or AUSDLJR EAY60869101 32LD350 CUSWLH or CUSDLH or CUSWLHO
P402
MAIN BOARD
P802
Main Boards Used in the 32LD350: EBU60850009 32LD350 AUSWLJR and AUSDLFR EBR66049702 32LD350 AUSDLJR EBU60850010 32LD350 AUSDLUR EBU60850003 32LD350 CUSDLH EBU61005102 32LD350 CUSWLH and CUSWLHO
P600
P2401
AC In
J2 J1
IR
p/n: EBR64965302
25
November 2010
32LD350
LCD-DV
26
Press inward on the two locking tabs and pull the connector out. P402 Flip the locking tab upward, pull the LVDS ribbon out.
P802 Remove any tape holding down any cables. Remove the 4 screws indicated by the arrows.
N/C
N/C
Decorative Metal Plate After removing the Main, there are tabs sticking through the Main board holding the Metal plate in place.
P600 NOTE: Always check on top and behind the Large ICs. And look for a piece of Chocolate (Heat Transfer Material). Be sure to transfer to new Board if present present.
P2401
Main Boards Used in the 32LD350: EBU60850009 32LD350 AUSWLJR and AUSDLFR EBR66049702 32LD350 AUSDLJR EBU60850010 32LD350 AUSDLUR EBU60850003 32LD350 CUSDLH EBU61005102 32LD350 CUSWLH and CUSWLHO
27
Remove the 6 screws indicated by the arrows. Remove the Inverter Cover.
Backlight connector
28
NOTE: After removing the Inverter, pay attention to the Cushions behind the Inverter. Make sure to return them to there correct positions if they should fall or pull off with the board.
Connectors to the Backlights. The Inverter board slides into these connectors.
29
p/n EBR64965302
Disconnect J1 and J2 connectors. Remove the 1 screw and pull the board forward.
J2
30
TROUBLESHOOTING SECTION
Troubleshooting: g This section of the manual will discuss troubleshooting. Upon completion of this section the Technician will have a better understanding of how to diagnosis and resolve problems.
31
32
p/n EAY60868901
Cold Gnd Hot Gnd F501 3.15A/250V STBY 0V Run 388V From Hot Gnd
33
AC In
Relay
Bridge
5
1
Rectifier
P r i m a r y
S e c o n d a r y
24V Regulator
INV On
Stand By 3.5V
At point 3 TV is in Stand-By state. Energy Star compliant. Less than 1 Watt
24V
INV On
T-CON Inside Panel 12V LVDS Along with Video On LVDS cable
2
Q402
5
Audio_AMP IC600
12V
6 8 8
PWM-DIM Digital Dimming Manipulates Backlight Brightness
MAIN BOARD
2
Q401
Power On
12V 7
LVDS Video
2 3
RL_ON
PWR_On/ Off_1
Ft Control
34
November 2010
32LD350 3D-LCD
11.97V
11.97V
S G 2 6
1.84V
R439 10K
12V L412
R440 1.8K 11.97V 2.39V
Q409
4.99V
Q407
0.02V
Q406
R429 47K
L422 8 7 L421 8 7
+5V Normal
3.35V
IC406
0.68V
0.03V
12V L417
R459 10K
SMPS
MAIN Board
P201
PWR_ON 24V
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 3.41V 3.41V 3.41V 3.41V Gnd Gnd Gnd Gnd 11.97V 3.32V 11.97V 0.59V 11.97V 4.49V N/C 2.46V PWR On 24.19V 24.19V 24.19V 3.28V
P403
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
PWR ON 24V
+3.3V Normal
IC405
2 6
11.97V 2.39V
12V L416
R456 10K
2
PANEL_CTL R245 100
3.28V 3
Q402
0.89V R406 2 4.7K 0V 0.64V
Q401
R401
10K
Step 1
E5 R237
100
RL_On SAR0 A4
Step 2
KEY 1
1 L404
3.39V
3.5V_ST
3.5V_ST
C401 100uF
IR R193
0
Error_Out Pin 20: (Silk Screened A-DIM) Goes high (3.3V) when the backlights are told to +3.3V Normal come on. Goes back low when they light. If it goes high again on the 5th attempt to fire the backlights, the set shuts off. R419
H6
IC100 Mstar
1K
Q405
0V
18 19 20 21 22 23 24
+3.3V Normal
R473 0
R486 4.7K
3.32V
Step 3
R201 E9
100
Error_Out
GPIO 097
R472 0
R479 0
R424 0
P-DIM
35
November 2010
32LD350 3D-LCD
(A) Add a jumper between (3.5V STBY) pin 7, 8, 9 or 10 and Pin 1 (PWR_ON). Apply AC. This will turn on the power supply, relays will click. a) Check that the 24V and 12V power supplies are turned on, P201 (12V pins 17 19 and 21) P201 (24V pins 2 3 and 4) P203 (24V pins 1~5) 17, 2, The Backlights should turn on at this point. If the 24V and the Inverter On command is arriving at the Ballast, but no backlights, then see Ballast Section for further testing. (B) Remove AC power and Remove Jumper. SMPS and Ballast are OK.
36
Label PWR-ON 24V GND 3.5V Gnd n/c 12V INV-ON 12V ERROR 12V A-DIM n/c PWM-DIM
Run 3.28V 24.19V Gnd 3.41V Gnd n/c 11.97V 3.32V 11.97V 0V 11.97V 4.49V 0V 0.65V~3.25V
Diode Check 1.16V 0.73V Gnd Open Gnd Open Open Open Open Open Open Open Open Open (1) PWR_ON Pin 1 Turns on 12V, 24V to the Main and 24V to the Inverter P203 Pins 1~5. 1~5 (2) INV_ON Pin 18 (To P203 pin 12) Turns on the Backlights. (3) Error Pin 20 (From P203 pin 11 Silk Screened A-DIM) Goes high when the backlights are told to come on. Goes g g back low when they come on. If it goes high again on the 5th attempt to fire the backlights, the set shuts off. (4) A-DIM Pin 22 (To P203 pin 13 Silk Screened PWM-DIM) Is not used. (5) PWM-DIM Pin 24 (To P203 pin 14 Silk Screened Error_Out) can vary according to incoming video IRE level and OSD Backlight setting Output from the Video Processor IC100. Range 0.65V to 3.25V.
37
P203
(1) Error Pin 11 (To P201 pin 20 Silk Screened A-DIM) Goes high when the backlights are told to come on. Goes back low when they come on. If it goes high again on the 5th attempt to fire the backlights, the set shuts off. (2) INV_ON Pin 12 (From P201 pin 18) Turns on the Backlights. (3) A-DIM Pin 13 (From P201 pin 22 Silk Screened PWM-DIM) Is not used. (4) PWM-DIM Pin 14 (From P201 pin 24 Silk Screened Error_Out) can vary according to incoming video IRE level and OSD Backlight setting Output from the Video Processor IC100. Range 0.65V to 3.25V.
38
Power Supply Fuses and Connector SK100 Voltage and Diode Check
SK100 "SMPS" to AC IN Label L N STBY Run Diode Check OL OL
120Vac
F501
Bottom Left of SMPS
F100
F100 5A/250V AC IN N L L N
SK100
F100 (Diode Check) Red or Black Lead on Fuse (Open) Other Lead on Hot Ground Diode Mode values taken with all Connectors Removed
If reading th voltage on F501 right after di the lt i ht ft power off, it takes a very long time to bleed down to the reading given here.
39
BALLAST SECTION
The Ballast receives 24V from the SMPS on CN1 pins 1~5. The Inverter On (INV ON) command g p g ,( ) arriving on CN1 pin 12 starts the Ballast drive signals, (120Hz). P-DIM is delivered from the Main board through the SMPS to the Inverter on CN1 pin 14. The Ballast responsible for delivering approx. 1.2kV to each of the 8 Cold Cathode Florescent bulbs. This is accomplished by 8 step-up transformers, 1 for each lamp.
Cover On
Cover Off
40
Bottom Half
CN1
24V Fuse
41
P203
POWER SUPPLY
P201
P402
INV On/Off
18 9 18 10 11 12
Q405
IC100 MStar
G5 INV-On/Off
3.32V 3.5V_ST
Q402
1 2 1 2 3 4 5
Q401
E5 RL-ON
Error Normal is Low. But when the backlights are told to fire via INV_ON, this line goes high. When they fire, it goes back low. If they fail to light after 5 attempts, the set shuts off.
24V
24V Reg
Controller
24V
3 4 5
12V Reg
17 19 2 3
21 4
11 14 13
11 14 13
20 24 22
20 24 22
ERR
0.59V
E5 AB12
Error
PWB-2
VBR-B (PWM Diming) Manipulates the Backlight Brightness via Customers OSD. Manipulates the Backlight Brightness via the BCM Chip. Darker Picture, Darker Backlights to facilitate improved Contrast Ratio. 0.65V ~ 3.25V Range A-DIM (Analog Diming) Fixed Voltage, this line is not used.
42
November 2010
32LD350
LCD-DV
1 2 3
U1
Pin Pi 1 Pin 2 Pin 3 0V Gnd 24.07V
43
PWMPWM-DIM (Global Dimming) Explained: P-DIM P(PWM(PWM-DIM may also be called P-DIM, VBR-B, PDS, BCM-VBR-B) PVBRBCM-VBR-
44
CN1
F1 (Diode Mode Check) (Di d M d Ch k) Open (Red Lead on Fuse) 0.9V (Black Lead on Fuse)
F101 7A
45
46
STBY 0V 0V 0V 0V Gnd 0V
Diode Check Open Open O Open Open Gnd Open Not Used Inverter On Control
INV_ON
(3)
Pin 14. PWM_DIM can vary according to OSD Backlight setting and the incoming video IRE level. PWM-DIM is Output from the Video Processor IC100. Range 0.65V to 3.25V.
(2) A-DIM
(1) P-DIM
(3) ERROR
Pin 11. Normal low. Goes high when the Backlights are told to turn on by INV_ON. After backlights fire, go back low. Will repeat 5 times then shut off the set.
47
The Main board also develops several B+ sources on the board. STAND-BY VOLTAGES 3.3V_ST (Voltage direct from SMPS) GENERAL 5V_Normal (From 12V from SMPS) 5V_EXT LVDS 5V USB (From 12V from SMPS) Panel_VCC (12V Not generated, but switched AUDIO from the 12V arriving from the SMPS) SMPS). 1.8V (Made from 3.3V_Normal) TUNER and VSB CIRCUIT 24V (From Power Supply) 5V_TU (Made from 5V_Normal) 3.3V_TU (Made from 3.3V_Normal) 1.26V (Made from the 3.3V TU) 3.3V_TU) +1.2V_PVSB (Made from 3.3V_TU) +3.3V_PVSB (Made from 3.3V_TU) MStar IC100 Video Processors 1.2V, D1.5V, D1.8V_DDR, 1.26V_VDDP, 3.3V_VDDP, +3.3V_AVDD_MPLL T-CON IC9001 3.3V_VCC, -5V_VGL, 27V_VGH, 16V_VDD and HVDD (7.8V)
48
P600 To Speakers
P2401 To Front IR
EBU60850003 32LD350 CUSDLH (The one shown) EBU60850009 32LD350 AUSWLJR and AUSDLFR EBR66049702 32LD350 AUSDLJR EBU60850010 32LD350 AUSDLUR EBU61005102 32LD350 CUSWLH and CUSWLHO
49
P802
IC401
P402
SW100 Microprocessor Reset
L422
IC1
IC1450
IC406
L421
USB1 HDMI
Headphone
C B B E C E
12MHz
D1100
C
A2 A1
25MHz
Digital Video 18. IF p 17. IF n 16. IF AGC 15. Reset TUNER 14. 3.3V TDVJ-H001F 13. 1.26V 12. GND Analog Video 11. CVBS 10. NC Audio 9. SIF 8. NC Tuner Data 7. SDA Tuner Clock 6. SCL 5. NC 4. NC Tuner B+ 3. 5V 2. NC 1. NC
Q1104
Q1103
IC5001
3 2 2 1
SIDE A/V
JK1104
JK1102
JK1103
JK9800
P600
R-R+L-L+
P2401
Main Boards Used in the 32LD350: EBU60850009 32LD350 AUSWLJR and AUSDLFR EBR66049702 32LD350 AUSDLJR EBU60850010 32LD350 AUSDLUR Main Boards Used in the 32LD350: EBU60850003 32LD350 CUSDLH EBU61005102 32LD350 CUSWLH and CUSWLHO
50
November 2010
32LD350
LCD-DV
Q100
Q1100
Q1103-4
Q1105
5V Routing Pin for IC1100 [A1] 0.07V [A2] 4.98V [C] 4.37V
51
November 2010
32LD350 LCD-DV
Q407
B E C C
S G D
3 2 1 C
Q405 B
3 1 2
C E
B E
IC103
IC408
In
Gnd
Gnd Out
IC400
3 2 1
D7706
A2 A1
2
IC601
C
D7703 IC1100
B E C DS G C B
A1 A2
A1 A2
Q1101 Q1102 C
E B E B
C B E C
D102 Q600
IC7701
Q7701 Q7703
Q5004
C B E
IC1201
IC1104 IC1105
A1 A2
D1115 C
Q2405
E BE B C C
Q2406
52
November 2010
32LD350
LCD-DV
IC103
Reset Pin Generator [1] Gnd [2] 0V [3] 3.39V EEPROM Mstar 0V (Gnd) 0V (Gnd) 0V (Gnd) 0V (Gnd) 3.31V 3.31V 0V (Gnd) 3.31V
IC1100 Pin [1] [2] [3] [4] [5] [6] [7] [8] IC1104 Pin [1] [2] [3] [4] [5] IC1105 Pin [1] [2] [3] [4] [5] [6] [7] [8] Q407
IC104 Pin [1] [2] [3] [4] [5] [6] [7] [8] IC400
Earphone Amp 2.14V 0V (Gnd) 0.02V 2.19V 2.19V 4.37V 2.19V 2.18V Optical Audio Amp 1.64V 3.29V 0V (Gnd) 0V (Gnd) 3.29V EDID Data PC 0V (Gnd) 0V (Gnd) 0V (Gnd) 0V (Gnd) 4.7V 4.7V 4 7V 4.7V 4.7V
IC1201 Pin [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12] [13] [14] [15] [16] IC7701 Pin [1] [2] [3] [4] [5] [6] [7] [8] Q409
(+3.3V_AVDD_MPLL) Pin Regulator [In] 3.35V [Gnd] Gnd [Out] 3.34V Power_Det Pin 24V, 12V, 3.5V [1] 3.52V [2] 3.35V 3 35V [3] Gnd (+1.8V_Amp) Pin Regulator [1] Gnd [2] 1.81V [3] 3.31V PANEL_VCC Pin Control 1st Driver B 0.05V C 0.68V E Gnd
RS232 Data Buffer 3.34V 3.48V 0V 0V (-5.37V) 5.39V (-5.37V) n/c (0V) n/c (3.39V) n/c (3.35V) n/c (0V) 3.35V 0V 5.47V 0V (Gnd) 3.37V EDID Data HDMI2 0V (Gnd) 0V (Gnd) 0V (Gnd) 0V (Gnd) 4.7V 4.7V 4 7V 4.7V 4.7V
IC7702 Pin [1] [2] [3] [4] [5] [6] [7] [8] Q401
EDID Data HDMI4 0V (Gnd) 0V (Gnd) 0V (Gnd) 0V (Gnd) 4.69V 4.69V 4.69V 4.69V
Q1101-2
EARPHONE Pin MUTE B 0V C 0V E Gnd IR Buffer Pin 1st Driver B 0.6V C 0V E Gnd IR Buffer Pin 2nd Driver B 0V C 3.3V E Gnd Tuner SIF Pin (Sound) Buffer B 0.163 C Gnd E 0.85V HDMI 2 Det
Q2405
Power On/Off Pin Driver for Q402 B 0.64V C 0V E Gnd Power On/Off Pin Switch 1 3.39V (In) 2 0.89V (Ctl) 3 3.28V (Out) Inverter On/Off Pin Switch B 0.06V C 3.32V 3 32V E Gnd
Q2406
Q402
Q5004
IC408
Q405
Q7701 Pin B 0.63V 0 63V C 0V E Gnd Q7703 Pin [B] [G] [S] [D] D7706
IC601
PANEL_VCC Pin Switch S 11.97V (In) G 1.84V (Enable) D 11.97V (Out) 5V Routing Pin for IC7705 [A1] 0.03V [A2] 0V [C] 4.69V
Q600
Q406
D1115
D7703
3.5V Blocking Pin for Q7703 [A1] 0V [A2] 3.37V [C] 3.3V
53
November 2010
32LD350 LCD-DV
X100
12Mhz
Runs all the time Runs only when set is on
X1005
25Mhz
3.61V p/p
2.91V p/p
3.64V p/p
4.59V p/p
X100
X1005
MAIN Board
54
Main Board Connector P402 to Power Supply Voltage and Diode Check
P402
P402 Main Board" to P201 SMPS" Pin 1
(1)
Run 3.28V 24.19V Gnd 3.40V Gnd n/c 11.96V 3.32V 11.96V 0.59V 0 59V 11.96V 4.49V n/c 0.65V~3.25V
Diode Di d Check 1.16V 0.73V Gnd Open Gnd Open p Open Open Open Open O Open Open Open Open
55
P802
Note: The P N t Th Panel has an additional b d th t sets on t and t k th lh dditi l board that t top d takes the 12V to generate the 5 usable voltages for the Panel.
56
57
Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Label Gnd Gnd N/C N/C Gnd TXA3+ TXA3Gnd TXAC+ TXACGnd TXA2+ TXA2Gnd TXA1+
Run Gnd Gnd n/c n/c Gnd 1.14V 1.34V Gnd 1.25V 1.2V Gnd 1.16V 1.35V Gnd 1.15V 1 15V
Pin 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
Label TXA1Gnd TXA0+ TXA0Gnd N/C LVDS_Sel Gnd Gnd Gnd Gnd Panel_VCC Panel_VCC Panel_VCC Panel_VCC Panel VCC
Run 0.79V Gnd 0.79V 0.79V Gnd n/c 2.42 Gnd Gnd Gnd Gnd 11.97V 11.97V 11.97V 11.97V 11 97V
58
P2401
Label
(1) (1)
STBY 0V 0V Gnd 3.4V 3.4V 3.41V Gnd 0V 2V Gnd 0.02V 2.49V 2 49V
Run 0V 0V Gnd 3.39V 3.39V 3.39V Gnd 0V 1.98V 1 98V Gnd 3.3V 0V
Diode Check Open Open Gnd 1.52V 1.52V 0.9V Gnd 2.3V Open O Gnd 0.58V 2.14V 2 14V
SCL SDA
IR
Gnd +3.3V_Normal LED_R/BUZZ LED R/BUZZ Clock or Data pulses pulses (1.6V p/p)
59
Mute Pin 25
1.8V_Amp Pin 16
Use speaker out to test for defective Audio Amp IC600 ( , ) Note: (Normal, Audio B+) P600 CONNECTOR "Main" to "Speakers" Pin 1 2 3 4 LABEL SPK R( ) SPK-R(-) SPK-R(+) SPK-L(-) SPK-L(+) SBY 0V 0V 0V 0V Run 12.95V 12 95V 12.95V 12.95V 12.95V Diode Check Open Open Open Open
IC600
(1)
Circuit Location on the Main Board
P600
R- R+ L- L+
60
The IR board receives it operating B+ via J1 pin 6 (STBY 3.5V). The IR (Infrared) remote receiver can be measured (2V) at pin 9 of connector J1 or P2401 on the Main board in Stand-By. During run pin 9 reads (1.98V). The IR pulses (1.6V p/p) J1 pin 9 are sent to P2401 on the Main board and on to the Microprocessor (IC100) via pin C4. The Front Power LEDs are controlled by pins 8 (Blue LED) and 12 (Red LED) of J1. The K b Th Key board is routed to the IR board via J3 and output on J1 K 1 and K 2 li di t d t th b d i d t t Key d Key lines, (Key 1 pin 4 and Key 2 pin 5). Arriving at P2401 pins 4 and 5 on the Main Board. Then to the Microprocessor Pins A4 and B4.
61
p/n EBR64965302
J1
J2
p/n EBR64965302
IR Receiver
Diode Check R indicates Red Lead B indicates Black Lead IR Center Leg Ground
Power LEDs
63
J2 "Front IR" to Key Board" Run 0V 0V Gnd 3.39V 3.39V 3.39V Gnd 0V 1.98V Gnd 3.3V 0V Diode Check Open Open p Gnd Open Open Open Gnd Open Open Gnd Open Open O Pin 1 2 3 4 Label KEY 1 Gnd KEY 2 Gnd STBY 3.4V Gnd 3.4V Gnd Run 3.39V Gnd 3.39V Gnd Diode Check Open Gnd Open Gnd
Label
(1) (1)
STBY 0V 0V Gnd 3.4V 3.4V 3.41V Gnd 0V 2V Gnd 0.02V 2.49V 2 49V
SCL SDA
IR
64
The Key board is routed to the IR board from P3000 to J3 and output on J1 Key 1 and Key 2 lines. Arriving at P2401 pins 4 and 5 on the Main Board. Then to the Microprocessor Pins A4 and B4. On P3000 (Key 1 is pin 1 and Key 2 is pin 3), Pins 2 and 4 are ground. Key 1 / 2 Voltage and Resistance Chart with buttons pressed. Label ey Key 1 Function Vol + o Vol Menu Enter Resistance 17M 10M 5.27M 0.98M Voltage 1.70V 0 1.09V 0.52V 0.10V Voltage and Resistance taken with AC applied to the set. No Button N B tt pressed R i t d Resistance is Open and Voltage is 3.4V. Diode Check on Key 1 and Key p 2 is Open. Voltage with no key pressed 3.4V STBY and 3.39V RUN
Label Key 2
65
Installed
66
This section shows the 1 1X17 foldout thats available in the Paper and Adobe version of the Training Manual. g The Adobe version of this Training Manual allows the viewer to g zoom in and out making reading of the small text easier. This Power Point shows a graphical representation of the 1 X 17 1 foldout page so clarity is limited limited.
67
TO TFT MODULE PANEL BOARD P201 SMPS to P402 "Main PWB" Pin Label STBY 1 2-4 5-8 9-12
1 2 3
J1 Run 3.28V 24.19V Gnd 3.4V Gnd 11.96V Diode 1.16V 0.73V Gnd Open Gnd Open Pin 18 19 20 21 22 23 24
(4) (3) (2)
To Back Light
4 3 T109
(1)
1 2 2 3
P201
1
2 2
Q103 Q109
To Back Light
4 3 T108 1
1 3
(5)
Jumper
1 2 2 3
1 2 2 3
SMPS Used in the 32LD350: EAY60868901 32LD350 AUSWLJR or AUSDLFR or AUSDLUR or AUSDLJR
P402 to SMPS P201 Pin 1 2-4 5-8 9-12 13-16 17 18 19 20 21 22 23 24 Diode Check 2.75V Open Gnd 0.91V Gnd 2.58V 1.5V 2.58V 3.04V 2.58V Open Gnd Open
1 2 2 3
D251
D255
To Back Light
4 3 T107 1
2 3
D252
P203
CN1
F101 Diode Check Red lead Open Blk lead 0.9V Cold
D201
(1)
P201
T101
To Back Light
F101
24V 7A
T501
PWR-On Pin 1: Turns on 12V, 24V to the Main and 24V to the Inverter P203 Pins 1~5. INV-On Pin 18: Turns on the Backlights
(2)
IC101
Hot
LVDS
Q407
Panel Vcc 2nd Driver
T106
D502 D503
To Back Light
U1 4 T105 3 1 U3 4 T104 3 1 U201 U2
1 2 2 3
Q102
450V 68uF 450V 68uF
1) 2) 3)
C608
+
C607
-
To Back Light
Q103 Q109
2
Pin 1) 24.16V 1 2 2) 9.03V 3 3) 0V Pin 1) Gnd 1 2 2) 9.03V 3 3) 4.58V Pin 1) 24.16V 2) 9.03V 3) 0V Pin 1) 0V 2) Gnd 3) 24.07V
Error_Out Pin 20: (Silk Screened A-DIM) Goes high (3.3V) when the backlights are told to come on. Goes back low when they light. If it goes high again on the 5th attempt to fire the backlights, the set shuts off.
(4)
(3)
P402
L415
IC2
DDR
IC403
From 3.3V_ST Power On Switch
P802
Q409
B E C
B E
5V_USB
G S D
Q406
IC401
12V In
3
INV_CTL Driver
IC407
HDCP EEPROM +1.8V_DDR
SW100 Microprocessor Reset
C E B
Q405
1 2
1 2 C E B
Q402 Q401
1
From 3.3V_ST
IC408
+5V_Normal
12V In
Reset Gen
2
L423
IC105
Power_Det
IC103
IC1000
3.3V_TU In
L406
F100 5A / 250V
L422
+1.2V_PVSB
IC1
DDR
IC1450
Q104 Q108
2
IC406
IC405
3
L421
IC400
In
Gnd
IC104
MStar EEPROM
3.3V_Normal In
USB1 HDMI
+3.3V_Normal
1
Gnd Out
WP
Serial Flash
12V In
3.3V_ST In
IC102
Digital Video
EDID HDMI 4
IC1004
To Back Light Pin 4 of T103 ~ T110 Warning: Over 1.2Kv To each Backlight. To Back Light Pin 1 of T103 ~ T110
3 4 T103 1 1 2
Q107 Q101
2 1 2 3
D101
L
L600
L101 4 4 3
U1
2 1 2 3
SK100
P-DIM Pin 24 (Silk Screened Error_Out) can vary according to incoming video IRE level and OSD Backlight setting Output from the Video Processor IC100. Range 0.65V to 3.25V.
(5)
+3.3V_AVDD_MPLL +1.8V_AMP
IC601
3.3V_Normal In
2
A2 A1
D102 Q600
IC600
3.3V_Normal Pin 8 1.8V_Amp Pin 16 24V Amp_VCC Pins 32~35 24V Amp_VCC Pins 49~52
C B E
Mute Routing
CEC Switch
X100
B
Earphone Amp
IC7702 D7706
X1005 Q7702
B E C C
A2 A1
A1 A2
C S
Q7703
D G C E
D7705
A1 A2
12MHz
EDID HDMI 2
Q1100
C
Earphone Amp Mute
IC1100
C B E
Audio Mute
D7703 B
D1100
C
A2 A1
Q7701
HDMI Hot Swap
B E
IC7701
Q1105
Audio Amp
JK7700
J1 Ft IR
Diode Open Open Gnd Open Open 2.97V Gnd Open 2.77V Gnd Open Open
L607
R-R+ L-L+
L606
JK1104
IC1201 IC1104
Digital Video 18. IF p 17. IF n 16. IF AGC 15. Reset 14. 3.3V 13. 1.26V 12. GND C Analog Video 11. CVBS E B 10. NC Audio 9. SIF 8. NC 7. SDA 6. SCL 5. NC 4. NC 3. 5V 2. NC 1. NC
IC5001
3 2 2 1
SIDE A/V
Q5004
Put the 3 screws in on the right side for service position. P203 "SMPS" to CN1 "Inverter PWB" Pin 1,2,3,4,5 6,7,8,9,10 11 12 13
(3)
Key 1 / 2 Voltage and Resistance Chart with buttons pressed. Key 1 Resistance Function 17M Vol + 10M Vol 5.27M Menu 0.98M Enter Key 2 Resistance Function 17M CH + 10M CH 5.27M Power 0.98M Input Voltage 1.70V 1.09V 0.52V 0.10V
Q2406
B
A2 A1
EB
E C
Q2405 IC1105
D1115
JK9800
P600
R-R+L-L+
PC EDID
2Msec per/div 44V p/p 120Hz 50% P-DIM Pin 3 of T103 ~ T110
STBY 0V Gnd 0V 0V 0V 0V
P2401
J1 J2
A-DIM P-Dim
14
Voltage and Resistance taken with AC applied to the set. No Button pressed Resistance is Open and Voltage is 3.4V
P3000
Pin 1 Key 1 Pin 3 Key 2 Diode Check Open Pins 2 and 4 Gnd
Front IR
IR Receiver Power Button
Main Boards Used in the 32LD350: EBU60850009 32LD350 AUSWLJR and AUSDLFR EBR66049702 32LD350 AUSDLJR EBU60850010 32LD350 AUSDLUR EBU60850003 32LD350 CUSDLH EBU61005102 32LD350 CUSWLH and CUSWLHO
32LD350 MAIN (FRONT SIDE) SIMICONDUCTORS IC101 Pin [1] [2] [3] [4] [5] [6] [7] [8] IC105 Pin [1] [2] [3] [4] [5] [6] [7] [8] IC401 Pin [1] [2] [3] [4] [5] [6] [7] [8] Serial Flash Memory 0.05V 3.28V 2.26V 0V (Gnd) 0V 0V 3.28V (B+) 3.28V (B+) HDCP EEPROM 0V (Gnd) 0V (Gnd) 3.3V (B+) 0V (Gnd) 0V 3.3V 0V (Gnd) 3.28V (B+) 5V Regulator for USB 11.9V (In) 5.09V (Out) 5.09V (Out) 0V (Gnd) 3.25V (PWR On/Off1) 0.8V 5.05V 0V (Gnd) IC405 Pin [1] [2] [3] [4] [5] [6] [7] [8] IC406 Pin [1] [2] [3] [4] [5] [6] [7] [8] IC403 Pin [1] [2] [3] [4] [5] [6] [7] [8] (+1.26V_VDDC) Regulator 0.79V 0V (Gnd) 3.37V (In) 4.47V 3.34V 1.3V (Out) 1.3V (Out) 2.96V (PWR On/Off2_1) (+3.3V_NORMAL) Regulator 0V (Gnd) 11.92V (In) 0V (Gnd) 0.8V 0.84V 2.39V (PWR On/Off1) 3.35V (Out) 3.35V (Out) (+5V_NORMAL) Regulator 0V (Gnd) 11.92V (In) 0V (Gnd) 0.8V 0.84V 2.39V (PWR On/Off1) 4.98V (Out) 4.98V (Out) IC407 Pin [1] [2] [3] [4] [5] [6] [7] [8] IC1000 Pin [1] [2] [3] [4] [5] [6] [7] [8] IC1450 Pin [1] [2] [3] [4] [5] [6] [7] [8] (D1.8V) Regulator 0.8V 0V (Gnd) 3.38V 4.79V 3.35V 1.76V (Out) 1.76V (Out) 2.36V (PWR On/Off1) (+1.2V_PVSB) Regulator n/c 3.26V (Enable) 3.26V (In) n/c n/c 1.81V (Out) 1.21V n/c 5V Shot Protection for USB 0V (Gnd) 5V (In) 5V (In) 0V (USB-Ctl) 5V (Out) 5V (Out) n/c IC5001 (+1.26V) for Tuner Pin Regulator [1] 3.3V (In) [2] 1.26V (Out) [3] 0V (Gnd) Write Protect for IC101 Q7702 Pin B 0.63V C 0V E Gnd D1100 Pin [A1] 0.07V [A2] 4.98V [C] 4.37V D7705 Pin [A1] 0V [A2] 4.98V [C] 4.71V HDMI 4 Det
Pin B 0V C 2.26V E Gnd Q1103-4 Pin B 0V C 0V E Gnd Q1105 Pin B 0.63V C 0V E Gnd
EARPHONE MUTE
32LD350 MAIN (BACK SIDE) SIMICONDUCTORS IC103 Pin [1] Gnd [2] 0V [3] 3.39V IC104 Pin [1] [2] [3] [4] [5] [6] [7] [8] IC400 Reset Generator IC1100 Pin [1] [2] [3] [4] [5] [6] [7] [8] IC1104 Pin [1] [2] [3] [4] [5] IC1105 Pin [1] [2] [3] [4] [5] [6] [7] [8] D7703 Earphone Amp 2.14V 0V (Gnd) 0.02V 2.19V 2.19V 4.37V 2.19V 2.18V Optical Audio Amp 1.64V 3.29V 0V (Gnd) 0V (Gnd) 3.29V EDID Data PC 0V (Gnd) 0V (Gnd) 0V (Gnd) 0V (Gnd) 4.7V 4.7V 4.7V 4.7V 3.5V Blocking for Q7703 IC1201 Pin [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12] [13] [14] [15] [16] IC7701 Pin [1] [2] [3] [4] [5] [6] [7] [8] D7706 Pin [A1] 4.98V [A2] 0V [C] 4.69V RS232 Data Buffer 3.34V 3.48V 0V 0V (-5.37V) 5.39V (-5.37V) n/c (0V) n/c (3.39V) n/c (3.35V) n/c (0V) 3.35V 0V 5.47V 0V (Gnd) 3.37V EDID Data HDMI2 0V (Gnd) 0V (Gnd) 0V (Gnd) 0V (Gnd) 4.7V 4.7V 4.7V 4.7V 5V Routing for IC7702 IC7702 Pin [1] [2] [3] [4] [5] [6] [7] [8] Q401 EDID Data HDMI4 0V (Gnd) 0V (Gnd) 0V (Gnd) 0V (Gnd) 4.69V 4.69V 4.69V 4.69V Q407 PANEL_VCC Pin Control 2nd Driver B 0.679V C 0V E Gnd PANEL_VCC Pin Switch S 11.97V (In) G 1.84V (Enable) D 11.97V (Out) AMP_MUTE Pin Pin 25 IC600 B 0.08V C 3.35V E Gnd EARPHONE MUTE Q5004 Tuner SIF Pin (Sound) Buffer B 0.163 C Gnd E 0.85V HDMI 2 Det
EEPROM Mstar 0V (Gnd) 0V (Gnd) 0V (Gnd) 0V (Gnd) 3.31V 3.31V 0V (Gnd) 3.31V
Q409
Q7701 Pin B 0.63V C 0V E Gnd Q7703 Pin [B] [G] [S] [D] D102 Pin [A1] 0V [A2] 0V [C] 0V
Power On/Off Pin Driver for Q402 B 0.64V C 0V E Gnd Power On/Off Pin Switch 1 3.39V (In) 2 0.89V (Ctl) 3 3.28V (Out) Inverter On/Off Switch
Q600
(+3.3V_AVDD_MPLL) Pin Regulator [In] 3.35V [Gnd] Gnd [Out] 3.34V (+1.8V_Amp) Regulator
Q402
Q1101-2 Pin B 0V C 0V E Gnd Q2405 Pin B 0.6V C 0V E Gnd Q2406 Pin B 0V C 3.3V E Gnd
D1115
Power_Det Pin 24V, 12V, 3.5V [1] 3.52V [2] 3.35V [3] Gnd
Pin 6
Pin 7
Pin 9
Pin 10
Pin 12
5uSec per/div
625mV p/p
5uSec per/div
561mV p/p
5uSec per/div
548.5mV p/p
5uSec per/div
565.1mV p/p
5uSec per/div
349.9mV p/p
Clock (TXAC+)
Clock (TXAC-)
Pin 13
Pin 15
Pin 16
Pin 18
Pin 19
5uSec per/div
535.6mV p/p
5uSec per/div
540.7mV p/p
5uSec per/div
534.1mV p/p
5uSec per/div
583.9mV p/p
5uSec per/div
395mV p/p
32LD350 P802 LVDS CABLE WAVEFORMS: Waveforms taken using SMTP Color Bar input. All readings give the Scale 100mV and 5uSec per division Time Base related to scope settings.