Documente Academic
Documente Profesional
Documente Cultură
Joel Prabhakar Periathambi Ajit Narwal North Carolina State University 5th December, 2011
Honor Pledge
We, Ajit Narwal and Joel Prabhakar Periathambi, have neither given nor received any unauthorized aid on this project
Executive summary
Design for the fully-differential operational transconductance amplifier (OTA) was implemented using a folded cascode operational amplifier with PMOS-differential pair input and the required gain was achieved by employing gain-boosting operational amplifiers. The common-mode feedback (CMFB) circuit is that of a series-shunt feedback type (topology 41). All the design specifications were comprehensively met; however, the operational amplifier gain suffers from cross-over frequency distortion (further elucidated in section 2.4). 1.1)
Design results
Specifications
92 dB
CMRR PSRR Supply Voltage Power dissipation Slew rate Input-referred noise voltage
0.849V pk-pk single ended 1.624 V pk-pk differential Overlap with output range >0.5-V 0.1 to 1.05 with an overlap of 0.669 V >60dB 135.3dB >60dB 245.1dB 1.8V 1.8V <10mW 6.695mW >30 V/usec 33.08 V/usec <10 nV/Hz 9.96 nV/Hz Table 1
1.2)
Design Methodology
At the onset attempts were made to establish the circuit using a folded amplifier with gain boosting provided by a common-source second stage; rigorous calculations were followed by circuit simulations, however the circuit displayed severe limitations when it came to the overlap of the common-mode input voltage range and single-ended output (to the tune of 30mV),which rendered the circuit hard to implement for unity gain feedback even though substantial gain could be achieved through the secondstage. The second and the final circuit that was attempted was a folded cascode design. The proposed circuit used PMOSes for input for they provided a higher slew rate in comparison to NMOSes for the same current. Design on paper was based on the gain-bandwidth product (GBWP). Employing the gpdk180 design kit the nominal size of the input PMOSes was randomly decided upon to provide enough transconductance for a given current to achieve the basic specification of GBWP. One thing to be kept in
1
mind while designing folded cascades is that the current through NM5 (and NM1) shall be larger than the tail current through PM8. This prepared the arrangement for the worst case of differential wherein all the current is drawn to one leg of the input PMOSes which can occur when if inputs rail to one side. To make sure that the circuit endured the situation and the CMOSes were being driven in saturation (i.e. the circuit gain is maintained) INM5 (and INM1)>IPM8. The bottom current sources thus were designed accordingly and a rough idea of designing the other CMOSes in the circuit was gained. Fig.a) depicts the circuit in discussion. The design criteria also lend a valuable range of VDsats for CMOSes in the circuit. Since output swing, single ended, was 0.8 V the overdrive VDsatsI could be designed 0.25V, preferably on the lower side to ensure a safety margin.
Simulations were run for single ended circuit lending a gain of 57dB.
1.3)
Gain-boosting amplifiers
The (required gain) =92-57dB was the basis for the design of the gain-boosting amplifiers. The design parameters for NMOS operational amplifier is as under. It was made sure that the differential amplifier inputs were
Fig.b Gain-boosting amplifier design NMOSes if providing negative feedback to a PMOS. These operational amplifiers drive the gate of the CMOS to ensure that there is the source of PM4 is set to a set voltage, and which if set properly can allow only a Vdsat drop across PM6 and NM1 lending an output of the circuit a swing of 2Vdsat within each rail. Also voltage drop across PM6 becomes less dependent on Vout. Fig b) is an NMOS gain-booster. Another PMOS booster was designed as well. A circuit of this type comes with a few caveats. Firstly make sure that the feedback of the circuit is indeed negative or else positive feedback shall lead to oscillations. Secondly the input common mode range for booster amplifiers shall be within the range of the parent operational amplifier. This circuit lends the capacitor between gate and source of PM4 Miller effect and Cgs becomes effectively Cgs (1+A), A being the gain of the internal operational amplifier. This leads to reduction in frequency of the secondary pole which deteriorates the phase margin of the circuit2. This needs to be countered and hence these boosters need compensation. This shall be discussed under the sectionCompensation, section 1.4.
Jiang, Xin, Sanghyun Seo, and Yumin Lu. CMOS Single Stage Fully Differential Operational amplifier with 120 dB DC Gain (2003): 1-2. Print.
Fig.c Operating points for the main circuit, with the gain-boosting operational amplifiers inserted
1.4)
Common mode feedback is required in all fully-differential amplifiers having active loads. Here a topology was used which senses the output voltages in terms of current flowing through PM0. This can be classified as a sensor for the output voltage.
Gate of PM0 drives the gates of PM5 and PM6 until the common-mode output voltage is set to the desired point. The feedback is negative and the phase margin of the loop thus obtained has to be taken care of to ensure stability of the circuit.
1.5)
Compensation
Every circuit which includes feedback needs to be checked for stability and hence compensated for adequate phase-margin for operation over variations of process, voltage and temperature. As discussed in 1.4 the gain-boosting amplifiers induced a Miller effect on Cgs of PM4 and reduced the secondary pole frequency wp2 which deteriorated the phase margin of the loop, hence a capacitor was connected at the high impedance node (gain-boosting operational amplifier output) to ensure that the loop gain dropped to a low value at wp2. The unity-gain frequency of the gain-boosting operational amplifiers must lie between the 3-dB bandwidth of the original circuit and its unity-gain frequency ensuring a high gain during the bandwidth of the original circuit and such that at higher frequency the pole of the gainboosters doesnt affect the stability of the system. Likewise the CMFB circuit also needed compensation which was provided by the compensation capacitor of the main operational amplifier. 7
1.6)
While the initial stages of circuit design involved extensive use of ideal energy sources, these were finally replaced with circuits which require a trigger circuit and the regular Vdd supply=1.8V. These circuits were replaced by a current reference (Vgs based) biasing circuit. Here the produced current is independent of Vdd. One can notice two feedback loops in the biasing circuit, one positive and the other negative, here the negative feedback dominates the circuit and ensures circuit stability. The necessary bias voltages were obtained by the usage of a MOS transistor and its complementary in diode connection.
As seen from the response above the low frequency gain obtained was about 105dB with a healthy phase margin of 71o. The gain-bandwidth product was 554 MHz and the 3dB bandwidth of the circuit was 4KHz. These values not only meet but exceed the required specifications by a healthy margin.
10
11
12
13
14
The power supply rejection ratio or PSRR is a measure of circuit robustness against supply variations, both in Vdd and ground. The PSRR was calculated by plotting the differential gain while applying only a common mode input to the differential pairs of the OTA and adding a 1V AC to the power supply, versus the differential mode gain.
15
2.6) Noise
The design exhibited a noise, referred to the input, less than 10 nV/Hz. The main culprit devices were the current sourcing NMOS transistors in the cascade circuit (namely NM5 and NM1, refer fig. a)) followed by the input differential pairs.
16