Documente Academic
Documente Profesional
Documente Cultură
. SPECIFICATION
1. 2. 3. 4. 5. CAMERA SPECIFICATION SYSTEM REQUIREMENTS TFT LCD PANEL MARK CONNECTION DIAGRAM IDENTIFICATION OF FEATURES 4 5 6 8 9
. ADJUSTMENT
1. 2. 3. 4. 5. Digital camera service38 Adjustment items by changed parts 44 Adjustment 45 How to check the FIRMWARE VERSION 56 How to update the FIRMWARE 57
. PATTERN DIAGRAM
1. PARTS ARRANGEMENT FOR EACH PCB ASS Y 1) MAIN_TOP 58 2) MAIN_BOTTOM 59 3) TOP 60 4) STROBO60 5) CCD_TOP61 6) CCD_BOTTOM 61
. CIRCUIT DIAGRAM
1. BLOCK DIAGRAM 62
2. CIRCUIT DIAGRAM 1) MAIN_BLOCK_S500 63 2) MAIN_DSP_S500 64 3) MAIN_DDR_S500 65 4) MAIN_FEB_S500 66 5) MAIN_MEMORY_S500 67 6) MAIN_MOTOR_S50068 7) POWER_S500 69 8) TOP_S500 70 9) STROBO_S500 71 10) STROBO_S500 72 11) CCD_S500 73 12) KEY_S500 74 13) AUDIO_S500 75 14) LCD_S500 76 15) CRADLE_S500 77 16) MAIN_BLOCK_S600 78 17) MAIN_COACH_S600 79 18) MAIN_DDR_S600 80 19) MAIN_FEP_S600 81 20) MAIN_MEMORY_S600 82 21) MAIN_MOTOR_S600 83 22) POWER_S600 84 23) TOP_S600 85 24) STROBO_S600 86 25) KEY_S600 87 26) AUDIO_S600 88 27) LCD_S600 89 28) CRADLE_S600 90
. TROUBLESHOOTING
1. 2. 3. 4. Check List for repairing 91 Main troubleshooting 92 Pattern of Power PCB 96 How to check each parts 98
. SERVICE INFORMATION
1. The order of disassembly and assembly 107
. SPECIFICATION
1. CAMERA SPECIFICATION
Image Sensor - Type : 1/2.5" CCD
Effective Pixel Total Pixel S500 Approx. 5.1 Mega-pixel Approx. 5.3 Mega-pixel S600 Approx. 6.0 Mega-pixel Approx. 6.1 Mega-pixel
Lens - Focal Length : SHD Lens f = 5.8 ~ 17.4mm (35mm film equivalent : 35 ~ 105mm) - F No. : F2.8 ~ F7.1 (Wide), F4.9 ~ F12.4 (Tele) - Digital Zoom :Still Image mode : 1.0X ~ 5.0X Play mode : S500 : 1.0X ~ 10.1X S600 : 1.0X ~ 11.0X (depends on image size) LCD Monitor : 2.4" color TFT LCD (112,000 dots) Focusing - Type : TTL auto focus - Range : Normal : 80cm ~ infinity Macro : 5cm ~ 80cm (Wide), 40cm ~ 80cm (Tele) Auto Macro : 5cm ~ Infinity (Wide), 40cm ~ Infinity (Tele) Shutter - Type : Mechanical and Electronic shutter - Speed : 1 ~ 1/1,500 sec. (Manual : 8 ~ 1/1,500 sec.) Exposure - Control : Program AE Metering : Multi, Spot - Compensation : 2EV (0.5EV steps) - ISO Equivalent : Auto, 50,100, 200, 400 Flash - Modes : Auto, Auto & Red-eye reduction, Fill-in flash, Slow sync, Flash off - Range : Wide : 0.2m ~ 3.0m, Tele : 0.4m ~ 2.5m (ISO AUTO) - Recharging Time : Approx. 6 sec. Sharpness : Soft, Normal, Vivid Effect : Normal, B&W, Sepia, Red, Blue, Green, Negative, RGB White Balance : Auto, Daylight, Cloudy, Fluorescent_H, Fluorescent_L, Tungsten, Custom Voice Recording : Voice Recording (max.1 hour), Voice Memo in Still Image (max. 10 sec.) Date Imprinting : Date, Date&Time, Off (user selectable) Shooting - Still Image : Modes : Auto, Program, Scene Scene : Night, Portrait, Children (in Mode Dial), Landscape, Close-up, Sunset, Dawn, Backlight, Fireworks, Beach & Snow Mode Dial : Auto, Program, Manual, Movie, Scene, Portrait, Night, Children Shooting : Single, Continuous, AEB Self-timer : 10 sec., 2 sec., Double (10 sec., 2 sec.) - Movie Clip : With Audio or without Audio (user selectable, recording time : memory capacity dependent) Size : 640x480, 320x240, 160x120 (3X Optical Zoom, Mute during Zoom Operation) Frame rate : 30 fps, 15 fps Movie Editing (Embedded): Pause during recording, Still Image Capture Storage - Media :Internal memory : Approx.20MB flash memory External memory : MMC / SD card (Up to 1GB Guaranteed)
. SPECIFICATION
- File Format : Still Image : JPEG (DCF), EXIF 2.2, DPOF 1.1, PictBridge 1.0 Movie Clip : AVI (MJPEG) Audio : WAV - Image Size
*6M 5M 4M 3M 2M 1M 2816X2112 2592x1944 2272x1704 2048x1536 1600x1200 1024x768 VGA 640x480 VGA 96 114 125
These figures are measured under Samsung standard conditions and may vary depending on shooting s conditions and camera settings Image Play - Type : Single image, Thumbnails, Slide show, Movie Clip - Editing : Trimming, Resizing, Rotate, Effect Interface - Digital output connector : USB 2.0 - Audio : Mono - Video output : NTSC, PAL (user selectable) - Cradle Interface (Optional) Power Source - Primary Battery : 2 x AA Alkaline (High Capacity) - Rechargeable battery (Optional) : SNB-2512 (Ni-MH) SBP-2524 (Ni-MH) Included battery may vary depending on sales region. Dimensions (WxHxD) : 96.8 X 61.8 X 26.4mm (excluding the projecting parts of the camera) Weight : Approx. 136g (without batteries and card) Operating Temperature : 0 ~ 40 C Operating Humidity : 5 ~ 85% Software - Camera Driver : Storage Driver (Windows98/98SE/2000/ME/XP, Mac OS 9.2 ~ 10.3) - Application : Digimax Master Special Features : User-friendly Effect button, Easy Grip, 2.4 Large LCD, Convenient Mode Dial .S600 only.
2. SYSTEM REQUIREMENTS
For Windows PC with processor better than Pentium II 450MHz (Pentium 700MHz recommended) Windows 98/98SE/2000/ME/XP Minimum 64MB RAM 200MB of available hard disk space USB port CD-ROM drive 1024x768 pixels, 16bit color display compatible monitor (24bit color display recommended) For Macintosh Power Mac G3 or later Mac OS 9.2 ~ 10.3 Minimum 64MB RAM 110MB of available hard-disk space USB port CD-ROM drive
. SPECIFICATION
No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
Descripition Recording mode Battery Aperture Value / Shutter Speed Continuous shot Flash Self-timer Macro Metering Card inserted indicator Auto focus frame Camera shake warning Date / Time Exposure compensation White Balance ISO RGB Sharpness Image quality / Frame rate 6
Icons
F2.8, 1/30
2006/01/01 01:00 PM
RGB
. SPECIFICATION
19 20 21 22
Image size Number of available shots remaining Remaining time (Movie clip/ Voice recording) Voice memo Optical/ Digital Zoom bar/ Digital Zoom rate 12 00:01:30/ 01:00:00
No. 1 2 3 4 5 6 7 8 9 10 11 12
Descripition Play mode icon Battery Voice Memo Protect DPOF Recording date Image size Flash Shutter speed Aperture Value ISO Folder name & File name
Icons
. SPECIFICATION
Card Reader
SD Card
4. CONNECTION DIAGRAM
Lap top
USB Cable
AV Cable
IBM / MAC
TV Monitor AC Adaptor
. SPECIFICATION
5. IDENTIFICATION OF FEATURES
Mode dial Shutter button Strap eyelet Speaker Flash Power button
Microphone
Zoom W button (Thumbnail) Zoom T button (Digital zoom) LCD monitor E (Effects) button +/- button, Delete button Play mode / Printer button 5 function button
Tripod
. SPECIFICATION
Bottom
5-function button
Voice memo / Voice Recording / Up button Menu / OK button
10
. SPECIFICATION
Cradle
Top
Back
AC connection terminal
11
2. Install the DirectX, Digimax Master by selecting a button shown on the monitor.
12
13
14
3. After restarting the computer, connect the PC to the camera with the USB cable.
4. Turn the camera power on. The [Found New Hardware Wizard] will open and the computer will recognize the camera. If your OS is Windows XP, an image viewer program will open. If the download window of Digmax Master opens after starting Digimax Master, the camera driver was setup successfully.
If you have installed the camera driver, The [Found New Hardware Wizard] may not open. On a Windows 98 or 98 SE system, the Found New Hardware Wizard dialog box opens and a window asking you to select a driver file may appear. In this case, specify "USB Driver" in the CD supplied. (for Windows 98 and 98 SE).
15
FAQ
<< Windows >> * System Requirements - Windows 98/98SE, ME, 2000, XP (Digimax Master can be installed and run in the Windows 98FE but that is not covered by Samsung's warranty) - Pentium 450MHz or higher (Pentium 700MHz recommended) - Minimum 200MB hard disk space (1GB recommended) - Minimum 64MB RAM (128MB recommended) - 1024X768 pixels, 16-bit colour display compatible monitor. - DirectX 9.0 or later
* Using a Hand-made PC or a PC and OS that has not been guaranteed by the manufacturer is not covered by the Samsung warranty. * When the supplied software is installed in the Windows 2000 or XP, log on as an Administrator account. * If two or more USB devices are connected on a PC, some devices may not operate correctly. * Connect the camera directly to the PC. Don't use the USB usb or USB located on the keyboard. * The compter may not recognize the camera when the computer is resuming from the suspend or sleep mode. * If there are delays when the movie plays back on the camera, copy the files on the computer and play them back on the computer.
Q1. While the S/W installation, DirectX is inatalled. Do I have to install the program? A1. To play back a Movie taken with S500 on the computer without any delay, you must install the program. Click the Install button on the auto-run window and USB driver will be installed first and DirectX 9.0 is installed. On the Windows 98/98SE/ME, DirectX will installed automatically, on the Windows 2000/XP, your computer checks the version of DirectX. If an old version of DirectX was installed on your compter, DirectX 9.0 will install automatically. easily handling tasks related to multi-media and game programs on the Microsoft Windows operation system. DirectX allows direct access 2D, 3D graphics, sound, movie programs to hardware devices. So it is called 'DirectX'.
Q2. How can I check the version of installed DirectX? A2. Click 'Start Run and type 'DXdiag'. Click OK button and a window for checking the DirectX will display. You can check the version of installed DirectX on the window.
16
< Note > DirectX is required about 55MB hard disk space. It will take about 22MB hard disk space. It will change settings of applications and registries. You can't remove it as the OS doesn't have uninstall program.
Q3. My computer can't recognize the camera. A3. (1) Install the supplied USB Driver. (2) Check the USB cable connection between the compter and camera. (3) The connected camera must be turned on. If the battery capacity is low, change it with fully charged one or use the AC adapter. 4) USB menu of the camera setting must be set as Computer. You can change the setting in the Setup menu of the camera by using the 5 function button. (5) If connect the camera to the computer without installing the USB Driver, the compter may not recognize the camera. In this case, remove the cable and install the USB drive first. 6) If other USB cables are connected to the compter, remove them. Sometimes the devices crash each other. Remove them and reboot the computer. And then check whether the computer can recognize the camera. (7) If the steps 1-6 are correct, remove the USB driver and install again.
Q4. How can I check whether the USB Driver was installed correctly? A4. Install the USB Driver and connect the camera and the computer with the supplied USB cable. And then turn them on. You can find the removeable disk. (1) "The device is working properly" message will display on the system information window. (2) The camera driver file has to be installed under the following folders. < Windows 98/98SE > S500.inf : Windows/inf DSCPDR.pdr : Windows/system/iosubsys DSCSYS.sys : Windows/system32/drivers < Windows ME / 2000 / XP > usbstor.sys : Windows/system32/drivers usbstor.inf : Windows/inf
17
Q5. Removing the USB Mass Storage driver for Windows 98/98SE A5. When you remove the USB drivr files for Windows 98/99SE manually, refer to the following steps. 1) Click [Control Panel Program Add/Remove] and remove the Digimax S500. (2) Click [Start Run]. (3) Type "regedit" to run the regedit program. (4) Select "HKEY_LOCAL_MACHINE/Enum/SCSI/SAMSUNG_DIGITAL_CAMERA_" and delete the VID :0839, PID:103F folders by pressing the DEL button. (5) Select "HKEY_LOCAL_MACHINE/Enum/USB" folder and delete VID_0839&PID_103F folder by pressing the DEL button. 6) Select "HKEY_LOCAL_MACHIN/System/CurrentControlSet/Services/Class/hdc" folder. Select each folders related with "S500.inf" and delete them by pressing the DEL button. The registry structures of Window 2000/XP are different from other Operating Systems. You must check the folder name before deleting the data. To delete the data, you must log on as administrator account.
Q6. Does S500 support USB 2.0? A6. S500 supports full speed of USB 2.0.
18
Digimax Master 1.0 Digimax Master : This is the all-in-on multi media software solution. You can download, view, edit and save your digital images and movie clips clip with this software.
1. Functions (1) AutoDownload : This program will download images captured with Samsung camera automatilcally. - Click [File Basic settings Find Option] and then check the "....................." option.
(2) Viewer : You can view the stored images easily. (3) Image edit : You can edit the still image. (4) Movie edit : You can edit the movie and save it as *.avi, *.asf, *.wmv file type. 2. Essential codec - Must be installed : DirectX 9.0c or later (Install separately) - QuickTime 6.5 : This program is required for playing back the *.MOV type file. (Install separately) 3. I want send a mail with captured image. But E-mail icon is not activated. - You did not set a default mail program. set the Microsoft Outlook Express as the default MAPI client.
19
1-2
1-3 1-4
1-4
1-1
1-4
20
2. BODY ASSEMBLY
2-30
2-31
2-8
2-23
2-29
2-8
2-17
2-25 2-21
2-22
2-20
2-18
2-8
2-26
2-8
2-7 2-14 2-5 2-33 2-12 2-15 2-13 2-16 2-1 2-2 2-3 2-4
2-8
2-6
2-11 2-32
22
3. BARREL ASSEMBLY
3-42 3-9
3-41 3-13
3-14
3-40 3-12
3-23
3-24 3-25
3-1 3-7 3-2 3-15 3-8 3-4 3-18 3-17 3-10 3-16
3-19
3-20
3-124
3-24
3-26
3-3 3-36
3-37
3-33
3-32
3-31
3-28
3-30 3-29
24
4. BARRIER ASSEMBLY
4-4
4-1
4-6
4-2
4-7
26
5-10 5-8
5-14 5-27
5-15 5-17
5-16 5-21 5-25
5-1 5-2
5-22
5-5
28
6-1
6-4
6-6
6-5
30
7. CRADLE ASSEMBLY
7-1
7-2
7-3
7-4
7-5
7-6
7-7
7-8
7-9
32
8. PACKING ITEM
8-4 8-22 8-19 8-20 8-12
8-17
8-18
8-1
8-7 8-3
8-6
8-5
34
. ADJUSTMENT
1. Digital camera service
To take a digital camera service (Repair, Tuning and Checking), the following equipments have to be arranged.
The sequences for the camera service are as shown. Receiving the camera
1. Receiving the camera When receiving a camera, check whether the accessories are included or not and ask the customer exact problems. 2. Checking the camera Checking the camera with priority given to the exact problems to find overall malfunctions. 3. Repairing the camera Repair the camera malfunctions found at the step 2. 4. Inspection After repairing the camera, inspect all of the camera functions.
Tuning
Inspection
Finish
3. Tuning
The illustrations may be different from the real display in accordance with the camera model.
38
. ADJUSTMENT
No. 1
2 3 4 5 6 7 8 9 10 11
Description - Installing a digital camera driver or Checking the removable device - Checking the file transference(upload and download) - Playing back the still image or movie clip HARD RACK, For the compatibility test. by Operating System by the O/S(WIN 98SE, ME, 2000, XP) Driver CD, by camera models S/W CDs for installing a camera driver USB HUB For using all kinds of USB cable at a time USB cable, by camera models For checking file transference(upload and download) by camera models Chart for checking colors For checking color and image resolution before or after camera repair TV MONITOR For checking video output and whether NTSC/PAL can be selected Memory card by types checking card recognition by brands and sizes A/V CABLE For checking whether the image can be displayed on a external monitor POWER SUPPLY For checking camera power by camera models Power cable by camera models
39
. ADJUSTMENT
No. 1 2 3 4 5 6 7 8 9 10 11 12
Device A set of tools Cleaning paper Detergent container Parts case Anti-electricity mat Soldering sponge Air pump LIGHT BOX POWER SUPPLY Soldering iron Tester BATTERY & AC ADAPTOR
Description Pincette/ Screwdriver/ Discharger etc. For cleaning camera lens and camera parts For containing detergent For keeping various camera parts and disassembled camera parts For repairing table made from anti-electricity material For removing solder For removing various kinds of dust Color temperature 5100 7.5V 2.0A Soldering iron that can select temperature Portable tester that can test AC/DC, ,ect. AC ADAPTOR & Rechargeable battery by camera models - SBP3603/ SBP3605/ SBP3606 - SLB 1437 - SBP 1103
40
. ADJUSTMENT
No. 1 2 3 4 5 6
Device AE TESTER AWB LIGHT SOURCE BOX COLOR chart AF chart Chart for checking resolution TRIPOD
Description For tuning AE and STROBE For checking and tuning AWB For checking AWB and color of images For tuning AF For checking image resolution
41
. ADJUSTMENT
42
. ADJUSTMENT
No. 10 11 12
Checking item MANUAL focus. Take a movie clip with TELE zoom during 10 seconds. Take a chart with TELE zoom in a low light condition. monitor.
Check point - Check whether the icon and counter are displayed on the LCD - Check whether the recording time is displayed and there are a noise, dim frame and discontinuous frame in the movie clip. - Check whether the zoom rate is changed and there are unclear part, noise and dim part in the image. - The distance from the subject is 2M and have to use the FILL IN flash.
13
- Check whether the PLAY mode can be selected without any problem and there are any noise, frame shaking and discoutinuous frame. - Check the voice recorded in the still image and the movie clip. - Check whether the still image can be enlarged correctly with the 5 function button.
14 15 16
Start the slide show in the PLAY mode. Try to rotate the mode dial. Download a image from a PC with USB cable and check the image quality in a external monitor.
- Select 2 sec. of slide show interval time and check whether there are any noise, image shaking and discontinuous frame. - Check whether the mode dial is rotated with the equal force. - Check whether each camera mode can be recognized correctly. - Check whether there are unclear part, dim part, noticeable flare, noise, ghost image and smear. - Check whether all images are deleted.
17 18
Format the card in the PLAY mode. (Delete all images in the PLAY mode)
Check whether there is no image and - Check whether the NO IMAGE message is displayed on the reset the camera. Remove the card and turn off the camera. LCD monitor. - Check whether the LARGE, FINE icon and 0018 number are displayed. - Check whether the camera power is turned off without any problem.
43
. ADJUSTMENT
44
. ADJUSTMENT
3. Adjustment
To adjust all items, all kinds of code by items have to be inserted in program file and saved them to the SD card as TXT file type. The codes are listed below. < Description of TXT file >
Codes of program
<1> PROCESS CODE ; <2> 65535 ; <3> PROCESS CODE ; <4> 0 OR 1 ; <5> 0 OR 1 ; <6> CONDITION ; <7> SPEC ; <8> NOT <9> NOT <10> NOT <11> NOT <12> NOT <13> NOT <14> 0 <15> 0
Codes of program
Insert the PROCESS CODE that you want to adjust 65535 --> DEFAULT Insert the PROCESS CODE that you want to adjust Insert 1 to write adjusted code to the EEPROM To save the result data to the SD card, insert 1 or 0 Insert each adjustment item's condition (See each adjustment item) Insert each adjustment item's value (See each adjustment item) Not used Not used Not used Not used Not used Not used 0 --> DEFAULT 0 --> DEFAULT
If the program is saved as shown above, the file name has to be saved as STS253ADJ.TXT (for S500)/STS263ADJTXT(for S600). SD CARD SHOULD BE FORMATTED BEFORE USING. After inserting each code, [;] mark has to be inserted.
45
. ADJUSTMENT
1) OB SETTING
After changing the MAIN PCB, adjust the black color. < Codes of program >
BASIC PROGRAM
<1> PROCESS CODE ; <2> 65535 ; <3> PROCESS CODE ; <4> 0 OR 1 ; <5> 0 OR 1 ; <6> CONDITION ; <7> SPEC ; <8> NOT <9> NOT <10> NOT <11> NOT <12> NOT <13> NOT <14> 0 <15> 0 <1>18; <2>65535; <3>18,1; <4>1; <5>0; <6>1,0,0,0,1000,10; <7>35,0,0,0,1000,10; <8>; <9>; <10>; <11>; <12>; <13>; <14>65535; <15>0;
OB SETTING
< How to adjust > a. Insert the codes and save the program in the SD card. b. Insert the SD card to the camera and turn on the camera. c. After completing the adjustment, the camera will be turned off.
PREVIEW OB SETTING R: 1808 G: 1792 B: 1792 CAPTURE OB SETTING R: 1808 G:1808 B: 1808
46
. ADJUSTMENT
2) LENS SHADING
After changing the MAIN PCB, BARREL and CCD, adjust the brightness gaps between center of the lens and around the lens. < Codes of program >
BASIC PROGRAM
<1> PROCESS CODE ; <2> 65535 ; <3> PROCESS CODE ; <4> 0 OR 1 ; <5> 0 OR 1 ; <6> CONDITION ; <7> SPEC ; <8> NOT <9> NOT <10> NOT <11> NOT <12> NOT <13> NOT <14> 0 <15> 0 <1>8; <2>65535; <3>8,0; <4>1; <5>1; <6>1,100; <7>; <8>; <9>; <10>; <11>; <12>; <13>; <14>65535; <15>0;
LENS SHADING
< How to adjust the item > a. Prepare a AE TESTER that can test upto LV 16.10.2 b. Attach the camera to the AE TESTER. c. Change the LV to 9.00.1 d. Insert the codes and save the program in ths SD card. e. Insert the SD card to the camera and turn on the camera. f. After completing the adjustment, the camera will be turned off. If the adjustment is incomplete, <Figure 2-1> will display with beep sound. In this case, re-try the adjustment process.
PREVIEW OB SETTING R: 1808 G: 1792 B: 1792 CAPTURE OB SETTING R: 1808 G:1808 B: 1808
PROCESS FAIL Result : Shading Failure (7) Before : 196, 8, 73, 160, 100 After : 45, 53, 146, 66, 100 NG < Figure 2-2 >
47
. ADJUSTMENT
BASIC PROGRAM
<1> PROCESS CODE ; <2> 65535 ; <3> PROCESS CODE ; <4> 0 OR 1 ; <5> 0 OR 1 ; <6> CONDITION ; <7> SPEC ; <8> NOT <9> NOT <10> NOT <11> NOT <12> NOT <13> NOT <14> 0 <15> 0
< How to adjust the item > a. Prepare a POWER SUPPLY. b. Connect the camera to the POWER SUPPLY. c. Change the voltage to 2.71 d. Insert the codes and save the program in ths SD card. e. Insert the SD card to the camera and turn on the camera. f. The adjustment is complete automatically. The LCD will be turned off and the camera is turned off.
48
. ADJUSTMENT
BASIC PROGRAM
<1> PROCESS CODE ; <2> 65535 ; <3> PROCESS CODE ; <4> 0 OR 1 ; <5> 0 OR 1 ; <6> CONDITION ; <7> SPEC ; <8> NOT <9> NOT <10> NOT <11> NOT <12> NOT <13> NOT <14> 0 <15> 0 <1>9; <2>65535; <3>9,0; <4>1; <5>1; <6>2; <7>50; <8>; <9>; <10>; <11>; <12>; <13>; <14>65535; <15>0;
BACK LASH
<How to adjust the item> a. Insert the codes and save the program in the SD card. b. Insert the SD card to the camera and turn on the camera. c. After completing the adjustment, the camera will be turned off.
49
. ADJUSTMENT
BASIC PROGRAM
<1> PROCESS CODE ; <2> 65535 ; <3> PROCESS CODE ; <4> 0 OR 1 ; <5> 0 OR 1 ; <6> CONDITION ; <7> SPEC ; <8> NOT <9> NOT <10> NOT <11> NOT <12> NOT <13> NOT <14> 0 <15> 0
< How to adjust the item > a. Prepare a AE TESTER that can test upto LV 16.10.2 b. Attach the camera to the AE TESTER. c. Change the LV to 15.80.1 d. Insert the codes and save the program in ths SD card. e. Insert the SD card to the camera and turn on the camera. f. After completing the adjustment, the camera will be turned off. If the adjustment is incomplete, <Figure 5-2> will display with beep sound. In this case, re-try the adjustment process.
PROCESS FAIL TEST COUNT : 5 LUMINANCE : 510 LINE DELAY : 249 SHUTTER ADJ SUCCESS! TEST COUNT : 15 LUMINANCE : 3048 LINE DELAY : 109
50
. ADJUSTMENT
6) FLASH ADJUSTMENT
After changing the MAIN PCB and SUB PCB, adjust the FLASH. < Codes of program >
BASIC PROGRAM
<1> PROCESS CODE ; <2> 65535 ; <3> PROCESS CODE ; <4> 0 OR 1 ; <5> 0 OR 1 ; <6> CONDITION ; <7> SPEC ; <8> NOT <9> NOT <10> NOT <11> NOT <12> NOT <13> NOT <14> 0 <15> 0
FLASH ADJUSTMENT
<1>13; <2>65535; <3>13,1; <4>1; <5>1; <6>1300,100,620,500,345,245,10; <7>; <8>; <9>; <10>; <11>; <12>; <13>; <14>65535; <15>0;
< How to adjust the item > a. Arrange a 36% reflect chart in a darkroom. b. Arrange a camera in a darkroom. c. The distance between the reflect chart and the camera should be 80cm. d. Insert the codes and save the program in the SD card. e. Insert the SD card to the camera and turn on the camera. f. After completing the adjustment, the camera will be turned off. If the adjustment is incomplete, <Figure 6-2> will display with beep sound. In this case, re-try the adjustment process.
STROBO TEST TEST COUNT : 3 LUMINANCE : 3768 FAIL!! FLASH ADJ IN WIDE
51
. ADJUSTMENT
7) PUNT ADJUSTMENT
After changing the MAIN PCB and BARREL, adjust the PUNT. < Codes of program >
BASIC PROGRAM
<1> PROCESS CODE ; <2> 65535 ; <3> PROCESS CODE ; <4> 0 OR 1 ; <5> 0 OR 1 ; <6> CONDITION ; <7> SPEC ; <8> NOT <9> NOT <10> NOT <11> NOT <12> NOT <13> NOT <14> 0 <15> 0
PUNT ADJUSTMENT
<1>2; <2>65535; <3>2,3; <4>1; <5>1; <6>1,0,1,2,3,4,5,6,7; <7>7,245,51,248,43,240,41,238,47,244,49,246,38,235,63,230,13,225,25,228,29,220,36,218,44,224,53,226,51,215,67,210; <8>; <9>; <10>; <11>; <12>; <13>; <14>65504; <15>0;
< How to adjust the item > a. Arrange a chart for adjust the PUNT. b. Attach the camera to the tripod. c. The distance between the chart and the camera should be 80cm. d. Insert the codes and save the program in the SD card. e. Insert the SD card to the camera and turn on the camera. f. After completing the adjustment, the camera will be turned off. If the adjustment is incomplete, < Figure 7-2 > will display. In this case, re-try the adjustment process.
ZOOM 0 : 127 ZOOM 1 : 123 ZOOM 2 : 117 ZOOM 3 : 117 ZOOM 4 : 123 ZOOM 5 : 129 ZOOM 6 : 120 ZOOM 7 : 117 < Figure 7-2 >
52
. ADJUSTMENT
BASIC PROGRAM
<1> PROCESS CODE ; <2> 65535 ; <3> PROCESS CODE ; <4> 0 OR 1 ; <5> 0 OR 1 ; <6> CONDITION ; <7> SPEC ; <8> NOT <9> NOT <10> NOT <11> NOT <12> NOT <13> NOT <14> 0 <15> 0
BURNING TEST
<1>10; <2>65535; <3>10,0; <4>0; Specify the repeat times <5>0; <6>1,14,1,2,4,3,6,7,8,9,10,11,12,13,14,15; <7>; <8>; Camera function number <9>; <10>;0; Change '0' into '1' for adjust the DEFECT CELL <11>0,0,1,800,800,6,30000,0;Change the first and second code ingo '1' to adjust the DEFECT CELL <12>65535,0; <13>; <14>65408; <15>0;close lens
< How to test > a. Insert the camera function number to the <6> code. The first position is for repeat time (10 means 10 repeat time), the rest of the positions are for camera function. See the below list. CODE 1 2 3 4 5 6 7 8 DELETE ALL LCD ON WIDE TELE NOT USE FLASH ONSHOOTING FLASH OFF SHOOTING NORMAL SHOOTING Function CODE 9 10 11 12 13 14 15 Function MACRO SHOOTING CONTINUOUS SHOOTING(2) SELF TIMER (10 sec.) PLAY MODE SLIDE SHOW MOVIE CLIP RECORD MOVIE PLAY
b. Insert the codes and save the program in the SD card. c. Insert the SD card to the camera and turn on the camera. (Set the mode dial to a still image mode) d. The programed camera function will work. If the test is complete, the camera will be turned off.
53
. ADJUSTMENT
9) EEPROM READ
To read the data of EEPROM, refer to the below codes. < Codes of program >
BASIC PROGRAM
<1> PROCESS CODE ; <2> 65535 ; <3> PROCESS CODE ; <4> 0 OR 1 ; <5> 0 OR 1 ; <6> CONDITION ; <7> SPEC ; <8> NOT <9> NOT <10> NOT <11> NOT <12> NOT <13> NOT <14> 0 <15> 0 <1>16; <2>65535; <3>16,3; <4>0; <5>1; <6>0,540; <7>; <8>; <9>; <10>; <11>; <12>; <13>; <14>; <15>0;
EEPROM READ
< How to test > a. nsert the codes (from START ADDRESS 0 to END ADDRESS 540) and save the program in the SD card. b. Insert the SD card to the camera and turn on the camera. c. Turn on the camera and the DATA in the EEPROM will be copied in the SD card. The codes from ADDRESS 1 to 10 will display on the LCD monitor and the rest of codes will not display. d. Turn off the camera after reading and saving the data. e. If you read the SD card in your PC, you can find the STS2_E2PR.CSV file and you can check the EEPROM DATA.
54
. ADJUSTMENT
BASIC PROGRAM
<1> PROCESS CODE ; <2> 65535 ; <3> PROCESS CODE ; <4> 0 OR 1 ; <5> 0 OR 1 ; <6> CONDITION ; <7> SPEC ; <8> NOT <9> NOT <10> NOT <11> NOT <12> NOT <13> NOT <14> 0 <15> 0
EEPROM WRITE
<1>17; <2>65535;53248 <3>17,3; <4>0; <5>0; <6>Sum_ADD,ADDRESS 0,DATA, ,....,ADDRESS 158,DATA; <7>; <8>; Number of ADDRESSes you want to insert <9>; If you want to insert all addresses <10>; (from 0 to 540), 541 will display. <11>; <12>; <13>; <14>; <15>0;
< How to test > a. Insert the codes (from 0 to 540) and save the program in the SD card. b. Insert the SD card to the camera and turn on the camera. c. Turn on the camera and the data of EEPROM will be copied to the camera. d. When the copy is complete, turn off the camera.
55
. ADJUSTMENT
2. In any camera modes, press the UP button twice to select the Voice recording mode.
3. When the Voice recording mode is displayed on the LCD monitor, press the left, right, down and +.-/Delete button one by another to check the firmware. After checking, press the Power button to turn it off.
4 1 3 2
56
. ADJUSTMENT
3. Press the buttons in the same way as firmware version check and the firmware will be updated. When the update is progressing, AF lamp will be blinking.
4 1 2
4. When the camera turns off if the update is completed, remove the SD card and check the firmware.
When doing the firmware update, use the AC adapter. If the camera turns off while updating, the camera couldnot work. After updating firmware, reset the camera.
57
. PATTERN DIAGRAM
1. PARTS ARRANGEMENT FOR EACH PCB ASSY
1) MAIN_TOP
58
. PATTERN DIAGRAM
2) MAIN_BOTTOM
59
. PATTERN DIAGRAM
3) TOP
4) STROBO
60
. PATTERN DIAGRAM
5) CCD_TOP
6) CCD_BOTTOM
61
. CIRCUIT DIAGRAM
1. BLOCK DIAGRAM
62
. CIRCUIT DIAGRAM
2. CIRCUIT DIAGRAM
1) MAIN_BLOCK_S500
63
. CIRCUIT DIAGRAM
2) MAIN_DSP_S500
64
R56 VDDRTC
. CIRCUIT DIAGRAM
3) MAIN_DDR_S500
65
. CIRCUIT DIAGRAM
4) MAIN_FEB_S500
66
. CIRCUIT DIAGRAM
5) MAIN_MEMORY_S500
67
. CIRCUIT DIAGRAM
6) MAIN_MOTOR_S500
68
. CIRCUIT DIAGRAM
7) POWER_S500
69
. CIRCUIT DIAGRAM
8) TOP_S500
70
. CIRCUIT DIAGRAM
9) STROBO_S500
71
. CIRCUIT DIAGRAM
10) STROBO_S500
72
. CIRCUIT DIAGRAM
11) CCD_S500
73
. CIRCUIT DIAGRAM
12) KEY_S500
74
. CIRCUIT DIAGRAM
13) AUDIO_S500
75
. CIRCUIT DIAGRAM
14) LCD_S500
76
. CIRCUIT DIAGRAM
15) CRADLE_S500
77
. CIRCUIT DIAGRAM
16) MAIN_BLOCK_S600
78
. CIRCUIT DIAGRAM
17) MAIN_COACH_S600
79
. CIRCUIT DIAGRAM
18) MAIN_DDR_S600
80
. CIRCUIT DIAGRAM
19) MAIN_FEP_S600
81
. CIRCUIT DIAGRAM
20) MAIN_MEMORY_S600
82
. CIRCUIT DIAGRAM
21) MAIN_MOTOR_S600
83
. CIRCUIT DIAGRAM
22) POWER_S600
84
. CIRCUIT DIAGRAM
23) TOP_S600
85
. CIRCUIT DIAGRAM
24) STROBO_S600
86
. CIRCUIT DIAGRAM
25) KEY_S600
87
. CIRCUIT DIAGRAM
26) AUDIO_S600
88
. CIRCUIT DIAGRAM
27) LCD_S600
89
. CIRCUIT DIAGRAM
28) CRADLE_S600
90
. TROUBLESHOOTING
1. Check List for repairing
1) When received
Grasp customer's complaints exactely Check the product's condition of exterior view(damage by shock) Check the condition of battery and all kinds of cables(USB cable, AV cable, AC Adaptor) Check working condition with new battery or adaptor - ON/OFF - TELE/WIDE - Check if the image shows correctly with TFT LCD on (Turn on the TFT LCD and check if the image shows correctly) - Take a picture by pressing the shutter button - Turn the dial and check if modes change correctly Download from the camera by connecting it with PC and check if correctly Check if the image shows correctly with it connected to monitor
Discharge Positions
2) When repairing
Check the connectors' condition to each PCB(dirt, short, assembly, lean, etc.) Change each doubtful PCB one after another to find out bad PCB - When doubtful of Main PCB Ass'y, check the operating condition by assembling with a good Main PCB ass'y (Manufacture of checking machine for each bad PCB is in schedule) Refer to each page to fix bad items of each PCB Check the connections of each PCB before assembling covers and embarkation of the parts (soldering condition) with the naked eye Ateter assembling the camera, insert battery only when condition of the parts' embarkation and connection is all right (Inserting battery when the camera has inside-short will result in death or serious injury to the CPU and all parts) After setting the mode dial in position assemble the Top Cover and check if the dial nverts correctly
3) After repairing
A/S Check list for each item - To judge inferior goods, begin with doubtful PCBs, replacing one after another to replace bad parts ex.) When Main PCB ass'y is in trouble, try replacing it with inferior camera's fair Main PCB ass'y
91
. TROUBLESHOOTING
2. Main troubleshooting
1) The power can't be turned on
Check : Power input (Battery, Adaptor, etc.)
Check connection : Between the Main PCB and the TOP F PCB. Check soldering : Battery contact Check connection : Between the Main PCB and the FLASH F PCB.
92
. TROUBLESHOOTING
LCD
2. Download the Full version Firmware into the SD card. 3. Connect the power supply to the camera and turn on the camera. 4. The LED on the Main PCB will blink while the firmware is upgrading and the LED will be off after completing the upgrading. 5. After upgrading firmware, release the short on the Main PCB.
93
. TROUBLESHOOTING
TP22
TP7
94
. TROUBLESHOOTING
TP18 TP19
TP20
TP11 TP12
TP# 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23
TP NAME N75CCD CCDCNT 33CCD 45VCC 33HR CCDCNT2 33LCD BLEDP BLEDN 15CCD VCCMOT 33AUD CCDCNT3 PWSW BLCNT VDDPWR BATCHK 25M 33M 18M GND VCC 3_3VCC
Normal voltage -7.5 3.3V 3.0V 5.0V 3.3V 3.3V 3.3V 10.5V 1.5V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V VCC/2 2.5V 3.45V 1.75M 3.3V 3.3V 95
. TROUBLESHOOTING
FUSE
33VCC_CCD 33VCC_HR
96
. TROUBLESHOOTING
2) MAIN PCB(BOTTOM)
BACKLIGHT
45VCC
15VCC_CCD
UP1 33VCC_MAIN
18VCC_MAIN
97
. TROUBLESHOOTING
NO
The camera doesn't turn on and the current is between hundreds or thousands of mA.
NO
NO The voltage of TP4 is about 5.0V YES The voltage of TP11 is about 3.2V
The voltage of TP18 is about 2.5V Change the Main Board Change the UP1 NO YES
98
. TROUBLESHOOTING
a
The voltage of TP 20 is about 1.75V YES The voltage of TP 2 is 3.3V YES NO NO The voltage of TP 12 is 3.3V
b
Change the UF3
NO
99
. TROUBLESHOOTING
2) Flash Defect.
Check the XE TUBE condition (Breakage, incorrect assembly)
< How to check the Q1 IGBT > - 1,2,3+4 = about 4.7K - 1,2,3+5,6,7,8 and 4+5,6,7,8 = hundreds of K ~ several M
100
. TROUBLESHOOTING
3) Flashing Defect.
Check the connetion (soldering) of MAIN PCB
TS1
MAIN BOTTOM
101
. TROUBLESHOOTING
Check the connection of CCD F PCB When the assemble is correc, a line of silk will appear
JF1
102
. TROUBLESHOOTING
3.3V
4_5VCC TP :4.5V 3_3CCD :3V 3_3HR :3.3V C_F29, C_F36, C_F39 :3V C_F44 :3.3V C_F41, C_F41: -7.5V C_F33, C_F37 :15V
103
. TROUBLESHOOTING
Interference of MAIN PCB and CF_41 - Check the location of tape on the bakc of the LCD Check the protect tape of BACK LIGHT soldering
CF_41
104
. TROUBLESHOOTING
6) Defect related to AUDIO - First of all, check that the AUDIO is ON in the MENU. - When the MIC & SPEAKER are soldered, be careful of breakage by a high temperature.
Check the soldering condition of speaker
Check the connection of Top F PCB and whether the pattern of #12, 13are shorted or not
Voices are not recorded, output sound is too low MIC assemble error. Check the assembling condition
105
. TROUBLESHOOTING
Defect related to the card recognition Check the soldering condition of Card socket
106
. SERVICE INFORMATION
1. The order of disassembly and assembly
Caution
1. Do the disassembling and assembling camera where the blocking static electricity mat is on the table. 2. When handling the major PCBs of camera, please wearing the band which cuts off the electric current on the wrist. 3. When handling the major parts, be careful of below caution.
Parts
F PCB type
Caution
When assembling the F PCB to the CONNECTOR by using pincette, be careful of tearing and hooking.
etc.
Be careful of the handprinting while handling them. Using the pincette which has soft tip. The spot will be shown by using normal alchol when cleaning them. Do the repairing where is no dust.
PCB type
Wearing the band which cuts off the electric current and do the reparing where the blocking static electricity mat is on by preventing the defect of parts.
CONTACT type
107
. SERVICE INFORMATION
a
2. Take apart the BACK COVER. When disassemble the Back cover, take care not to break the connection part.
108
. SERVICE INFORMATION
CAUTION
After disassembling the LCD FRAME, you must discharge the Main condensor before doing the next step. Discharging point
109
. SERVICE INFORMATION
6. To disassemble the FRONT COVER, remove the MODE F PCB and a screw. ax1
CAUTION
When you disassemble the FRONT COVER, remove the MODE F PCB CONNECTOR first.
a
7. Disassemble the FRONT COVER.
8. To disassemble the MAIN PCB ASS'Y, remove the MODE F PCB soldering and screws. ax2
a
110
. SERVICE INFORMATION
9. To disassemble the MAIN PCB ASS'Y, remove the CCD F PCB and BARREL F PCB.
10. To disassemble the LENS ASS'Y, remove the screws. ax2 bX2
111
. SERVICE INFORMATION
11. To disassemble the STROBE ASS'Y, remove the screws. aX1 bX1
112
. SERVICE INFORMATION
113
. SERVICE INFORMATION
3. To disassemble the barrel, remove the screws that hold the F PCB. dX1
114
. SERVICE INFORMATION
Disassemble the Outer Guide Barrel from the Outer Cam Barrel. Rotate the Outer Guide Barrel to the Outer Cam Barrel guide part and disassemble it.
5. Disassemble the Outer Guide Barrel from the Outer Cam Barrel. Rotate the Outer Guide Barrel to the Outer Cam Barrel guide part and disassemble it. Guide part
115
. SERVICE INFORMATION
7. To disassemble the Guide Plate from the Cam Barrel, push inside the three point of the Guide Plate and pull the Guide Plate out of the Cam Barrel.
116
. SERVICE INFORMATION
9. To disassemble the Shutter Ass'y and 2nd Lens Ass'y, remove the F PCB Guide and screw. F PCB Guide
F PCB Guide
When disassemble the F PCB Guide, take care of the double-stick tape.
117
. SERVICE INFORMATION
When disassembling, take care of a tape stuck on the 2nd Lens Ass'y
After disassembling
f b
11. To disassemble the Gear and Motor of Lens Base, remove the screws. bX3 fX1
118
. SERVICE INFORMATION
12. Remove the Photo Interrupter and disassemble the Zoom Cover.
Zoom Gear A
119
. SERVICE INFORMATION
14. Remove two screws and disassemble the Zoom Motor. eX2
120
. SERVICE INFORMATION
AF Guide Holder
16. To disassemble the 3rd Lens Ass'y, remove the spring and disassemble the 3rd Lens Ass'y.
121
. SERVICE INFORMATION
17. To disassemble the AF motor Ass'y, remove the AF Clip Holder, screw and AF Clip. hX1
122
. SERVICE INFORMATION
Disassemble is complete
123
. SERVICE INFORMATION
When assembling the parts, F PCB must be attached on the 2nd Lens Ass'y firmly. Attached firmly
124
. SERVICE INFORMATION
3. Assemble the F PCB Giude. Take care of the direction. F PCB must be attached to the F PCB Guide firmly.
125
. SERVICE INFORMATION
4. Assemble the 2nd Lens Ass'y and Zoom Ring Ass'y. When assembling, arrange the grooves to view the Barrier Lever.
After assembling
Arrange the holes of 2nd Lens Ass'y and Zoom Ring Ass'y at the same position
5. Assemble the Cam Barrel and Guide Plate. When assembling them, press the Guide Plate slightly to assemble the Cam barrel. When they are assembled correctly, you can hear "Click".
126
. SERVICE INFORMATION
6. Arrange the boss part of the Outer Guide Barrel and guide part of the Outer Guide at the position shown as alongside and assemble them.
7. Assemble the Zoom Ring and the 2nd Lens Ass'y. Assemble the Cam Barrel and the Guide Plate. When assembling, rotate the Guide Plate to see the groove of Cam Barrel.
127
. SERVICE INFORMATION
The boss must be upper left side of the ass'y before assembling.
After assembling
128
. SERVICE INFORMATION
8. Assemble the Outor Cam Barrel and Outer Guide Barrel. Take care of the positions of screw hole of the Outer Cam Barrel and reflector of Outer Guide Barrel.
After assembling
129
. SERVICE INFORMATION
9. Rotate the Outer Cam Barrel to extract the barrier and screw it. Rotate the Outer Cam Barrel to the opposite direction to put it in.
10. Assmble it with the Lens Base Ass'y. Take care of the F PCB.
130
. SERVICE INFORMATION
131