Documente Academic
Documente Profesional
Documente Cultură
PRODUCT NAME
SP07CT99300 -010
2004/09/02 01 1/11
PUBLISHED BY
GPS RECEIVER/CT-9930
`gz
93. 9. 08
SPECIFICATION
SPEC NO. PART NO. PRODUCT NAME G G G SP07CT99300-010 07G211212000120 GPS RECEIVER/CT-9930
DESCRIPTION
48N/5V/HFL/11P/C/3100
REVISION STATUS VERSION 01 DATE PAGE REVISION DESCRIPTION PREPARED DESIGNED APPROVED Har k Har k Fr ank 2004/09/02 Whole New Issued
Pr epar ed By
Designed By
Appr oved By
92.05.30
All right reserved by Cirocomm Technology Corporation.
B400-010.01
SP07CT99300 -010
2004/09/02 01 2/11
PUBLISHED BY
GPS RECEIVER/CT-9930
`gz
93. 9. 08
INDEX
Item No. 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0 11.0 12.0 Cautions Absolute Maximum Rating
Nor mal Oper ating Conditions Electr ical Char acter istics Module Specification Time to Fir st Fix (TTFF) Module Inter face Communication Specification
Contents
Page 3 4 4 4 5 6 6 6 7 8 9 11
Recommend Antenna Specifical Dimension GPS Receiver Module Configur ation Reference
SP07CT99300 -010
2004/09/02 01 3/11
PUBLISHED BY
GPS RECEIVER/CT-9930
`gz
93. 9. 08
1.0 Cautions
GPS (Global Positioning System) is a satellite-based navigation system. In an unobstructed clear view of the sky, GPS works anywhere in the world, 24 hours a day. GPS is developed and operated by the government of United States. Under the policy of the government, the degradation in accuracy shall occur without prior warnings, and sometimes satellites dont transmit signal due to adjustment, test, and orbital revision. Please be aware that the performance of the GPS receiver module does not warrant against the above factors. Also, please note: 1. products such as motors, computer, and RF devices, which emmit high levels of magnetic field and interference that may cause the performance of the GPS unit to drop. 2. the optimal position during automobile applications is on the roof top of the vehicles. If the GPS unit is to be placed inside the car, be certain to avoid coverage by metal objects for optimal performance. (Position Accur acy) Position data and position accuracy are affected or degraded by the satellite geometry, electric magnetic interference, and multipath. (Equipment) The high frequency noise will interfere with signal receiving. The high frequency noise within the receiver frequency band, 1575Mhz 10MHz, will affect the receiver quality. Also, because of the mixer and modulation, the low frequency noise will be increased by several times. If this increased frequency drops into the 1575MHz 10MHz band, it will also affect the receiver quality. Another warning should be notified. GPS receiver modules should not be placed close to heat and fans. Drastic changes in temperature will degrade the signal receiving strength even when operating within the operation temperature. Crystal and crystal oscillator on PCB ASSY should be kept away from the cooling fan. (Power ) If the impedance of the power terminal is too high (power cable too thin and over 10 cm long), then S/N will be degraded. Please insert condenser (above 47gF) into cable terminal to remove ripple. (Oper ation) Static electricity will destroy IC and erase backup data. Wear anti static electricity bundle while you are using the GPS Receive Module). Besides static electricity, plugging in or out the connector while power on will cause initialization. Make sure this is performed under power-off condition.
SP07CT99300 -010
2004/09/02 01 4/11
PUBLISHED BY
GPS RECEIVER/CT-9930
`gz
93. 9. 08
(Antenna) In order to strengthen the sensitivity for car navigation, GPS antenna is suggested to mount on a flat place around 80x80mm.
(War r anty) If the product fails within one year after the date of delivery while it has been used properly it will be replaced or repaired free of charge. (Environmental conditions) The product should be suitably installed or shielded so that it should not be affected by high frequency (1575.42MHz10MHz) noises from other devices like CPUs. Dont allow the airflow from the cooling fan to come directly to the quartz crystal oscillator in the receiver module. 2.0 Absolute Maximum Ratings Note: This module is not intended to operate under the conditions listed in Absolute Maximum Ratings. Continuous operation under these conditions or exceeding the maximum ratings may result in permanent damage to this device. Symbol
Vcc VI TA T STG
Parameter
Module Supply Voltage Input Voltage Ambient Temp. (Power applied) Stor age Temp.
Min
- 0.3 - 0.3 - 40 - 40
Typ
5.0
Max
9
Vcc
Units
V V
C C
95 95
Parameter
Vcc Supply Voltage
Min 3.0
Apd ANT-V
Vcc Supply Voltage Noise Module Power Dissipation (not including ANT power ) Oper ational Temp. (Power applied) -40 Exter nal supply voltage to RTC. 2.5 VBATT cur rent consumption. 2.5V 3.5V 5.0V Power Down model Cur rent Output to ANT DC voltage Vcc-0.5
Max 7.5 50
Units V mVP-P mW C V uA
85 5.0
150 Vcc
uA V
Symbol
VIH VIL VOH VOL
Parameter
Module Supply Voltage Input signal high level Input signal low level Output signal high level IOH = 1mA Output signal low level IOL = 1 mA
Min 3.0
1.5 -0.3 Vcc-0.5 0
Typ 5.0
Max 7.5
Vcc 0.84 Vcc .22Vcc
Units V
V V V V
SP07CT99300 -010
2004/09/02 01 5/11
PUBLISHED BY
GPS RECEIVER/CT-9930
`gz
93. 9. 08
5.0 Module Specification Dimensions Satellite Tracking RF input Center frequency Characteristics impedance Signal sensitivity
50mm * 30mm * 13mm(L*W*H) 12 Parallel channels 1575.42MHz L1 band, C/A code 50 ohm -145 dBm (Searching Mode) -157 dBm (Tracking) WGS-84 All major coordinate systems 10 m CEP (50%) 0.2m/s (50%) 4g Default 1 second (see 13.2.5) 40X to 85X C C 40X to 95X C C 3.0 V 7.5 V ( Linearly regulated ) Same as board supply or Separate external supply (e.g. 5V) External active 60 mA, 170 mW (Active antenna power not included) asynchronous data I/O ports RTC Back-up battery input
Positioning system
Positioning accuracy
Follow-up performance Navigation Update Rate Operation Temperature Storage Temperature Operating voltage Antenna supply
I/O port
Mbits
of
on-board
volatile
SP07CT99300 -010
2004/09/02 01 6/11
PUBLISHED BY
GPS RECEIVER/CT-9930
`gz
93. 9. 08
6.0 Time To Fir st Fix (TTFF) Typical Condition: 8 satellites in view + all previous conditions stand. Hot Start (time, position, valid ephemeris, and valid almanac) Warm Start (time, position, no ephemeris, and valid almanac) Cold Start (no time & position, no ephemeris, and no almanac) 7.0 Module Inter face RF input connector I/O connector (Power supply, serial data) 12 seconds 35 seconds 50 seconds
8.0 Communication Specification Communication method Transfer rate input/output Logic levels I/O code Communication format
SP07CT99300 -010
2004/09/02 01 7/11
PUBLISHED BY
GPS RECEIVER/CT-9930
`gz
93. 9. 08
9.0 Recommended Antenna Specification Antenna Center frequency Polarization Gain Axis ratio Pr e-amplifier Gain Noise figure (NF)
1575.42MHz Right-handed circular polarization -5dBi or more (5X Angle of elevation) 3dB typical (Angle of elevation = 90)
Over all Specification Gain Output impedance Output VSWR Supply voltage Maximum Current consumption
17dBi or more (Angle of elevation = 90) 50 ohms 2.0 or less GPS active Antennas working voltage must match the VCC. 30mA
SP07CT99300 -010
2004/09/02 01 8/11
PUBLISHED BY
GPS RECEIVER/CT-9930
`gz
93. 9. 08
10.0 Dimension
SP07CT99300 -010
2004/09/02 01 9/11
PUBLISHED BY
GPS RECEIVER/CT-9930
`gz
93. 9. 08
Pin Configur ation Pin No. 1 2 3 4 5 6 7 8 9 10 11 Symbol GND V-Batter y TXD RXD0 VCC N.C N.C N.C N.C N.C GND I/O Ground I O I I Description Power and signal ground Batter y Voltage input. UART Por t, Tr ansmit Data output. UART Por t, Receive Data input. GPS Module & active ANT power input. No connection. No connection. No connection. No connection. No connection. Power and signal ground
Ground
Coaxial Cable
RF Cable with H.F.L. connector GPS Module I/O I/O Connector See Pinout Table for connections GPS Module I/O I/O Connector See Pinout Table for connections
SP07CT99300 -010
2004/09/02 01 10/11
PUBLISHED BY
GPS RECEIVER/CT-9930
`gz
93. 9. 08
1/2 VDD
GND
Minimum 100 uS
SP07CT99300 -010
2004/09/02 01 11/11
PUBLISHED BY
GPS RECEIVER/CT-9930
`gz
93. 9. 08