Documente Academic
Documente Profesional
Documente Cultură
PointSource Ai 5050
SERVICE MANUAL
Published in May 99 2AD70761 Revision 1
PointSource Ai 5050
CAUTION
DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE RECOMMENDED BY THE MANUFACTURER. DISPOSE OF USED BATTERIES ACCORDING TO THE MANUFACTURERS INSTRUCTIONS.
ATTENTION
IL Y A DANGER DEXPLOSION SIL Y A REMPLACEMENT INCORRECT DE LA BATTERIE. REMPLACER UNIQUEMENT AVEC UNE BATTERIE DU MME TYPE OU DUN TYPE RECOMMAND PAR LE CONSTRUCTEUR. METTRE AU RBUT LES BATTERIES USAGES CONFORMMENT AUX INSTRUCTIONS DU FABRICANT.
Service Manual
PointSource Ai 5050
Safety precautions
This booklet provides safety warnings and precautions for our service personnel to ensure the safety of their customers, their machines as well as themselves during maintenance activities. Service personnel are advised to read this booklet carefully to familiarize themselves with the warnings and precautions described here before engaging in maintenance activities.
DANGER:
High risk of serious bodily injury or death may result from insufficient attention to or incorrect compliance with warning messages using this symbol.
WARNING: Serious bodily injury or death may result from insufficient attention to or incorrect compliance with warning messages using this symbol. CAUTION: Bodily injury or damage to property may result from insufficient attention to or incorrect compliance with warning messages using this symbol.
Symbols The triangle ( ) symbol indicates a warning including danger and caution. The specific point of attention is shown inside the symbol. General warning.
Warning of high temperature. indicates a prohibited action. The specific prohibition is shown inside the symbol. General prohibited action.
Disassembly prohibited.
indicates that action is required. The specific action required is shown inside the symbol. General action required.
1. Installation Precautions
WARNING Do not use a power supply with a voltage other than that specified. Avoid multiple connections to one outlet: they may cause fire or electric shock. When using an extension cable, always check that it is adequate for the rated current. ............................................................... Connect the ground wire to a suitable grounding point. Not grounding the copier may cause fire or electric shock. Connecting the earth wire to an object not approved for the purpose may cause explosion or electric shock. Never connect the ground cable to any of the following: gas pipes, lightning rods, ground cables for telephone lines and water pipes or faucets not approved by the proper authorities. ........................
CAUTION: Do not place the copier on an infirm or angled surface: the copier may tip over, causing injury. ........................................................................... Do not install the copier in a humid or dusty place. This may cause fire or electric shock. ..................................................................................... Do not install the copier near a radiator, heater, other heat source or near flammable material. This may cause fire. ....................................... Allow sufficient space around the copier to allow the ventilation grills to keep the machine as cool as possible. Insufficient ventilation may cause heat buildup and poor copying performance. ...............................
Always handle the machine by the correct locations when moving it. .... Always use anti-toppling and locking devices on copiers so equipped. Failure to do this may cause the copier to move unexpectedly or topple, leading to injury. .......................................................................... Avoid inhaling toner or developer excessively. Protect the eyes. If toner or developer is accidentally ingested, drink a lot of water to dilute it in the stomach and obtain medical attention immediately. If it gets into the eyes, rinse immediately with copious amounts of water and obtain medical attention. .................................................................................... Advice customers that they must always follow the safety warnings and precautions in the copiers instruction handbook. ...................................
Always use parts having the correct specifications. ............................... Always use the thermostat or thermal fuse specified in the service manual or other related brochure when replacing them. Using a piece of wire, for example, could lead to fire or other serious accident. ........... When the service manual or other serious brochure specifies a distance or gap for installation of a part, always use the correct scale and measure carefully. ........................................................................... Always check that the copier is correctly connected to an outlet with a ground connection. .................................................................................
Check that the power cable covering is free of damage. Check that the power plug is dust-free. If it is dirty, clean it to remove the risk of fire or electric shock. ......................................................................................... Never attempt to disassemble the optical unit in machines using lasers. Leaking laser light may damage eyesight. .............................................. Handle the charger sections with care. They are charged to high potentials and may cause electric shock if handled improperly. .............
CAUTION Wear safe clothing. If wearing loose clothing or accessories such as ties, make sure they are safely secured so they will not be caught in rotating sections. ..................................................................................... Use utmost caution when working on a powered machine. Keep away from chains and belts. ............................................................................. Handle the fixing section with care to avoid burns as it can be extremely hot. ......................................................................................... Check that the fixing unit thermistor, heat and press rollers are clean. Dirt on them can cause abnormally high temperatures. ......................... Do not remove the ozone filter, if any, from the copier except for routine replacement. ............................................................................... Do not pull on the AC power cord or connector wires on high-voltage components when removing them; always hold the plug itself. .............. Do not route the power cable where it may be stood on or trapped. If necessary, protect it with a cable cover or other appropriate item. ........ Treat the ends of the wire carefully when installing a new charger wire to avoid electric leaks. ............................................................................
Remove toner completely from electronic components. ......................... Run wire harnesses carefully so that wires will not be trapped or damaged. ................................................................................................
After maintenance, always check that all the parts, screws, connectors and wires that were removed, have been refitted correctly. Special attention should be paid to any forgotten connector, trapped wire and missing screws. ...................................................................................... Check that all the caution labels that should be present on the machine according to the instruction handbook are clean and not peeling. Replace with new ones if necessary. ...................................................... Handle greases and solvents with care by following the instructions below: ..................................................................................................... Use only a small amount of solvent at a time, being careful not to spill. Wipe spills off completely. Ventilate the room well while using grease or solvents. Allow applied solvents to evaporate completely before refitting the covers or turning the main switch on. Always wash hands afterwards. Never dispose of toner or toner bottles in fire. Toner may cause sparks when exposed directly to fire in a furnace, etc. ......................... Should smoke be seen coming from the copier, remove the power plug from the wall outlet immediately. ..................................................
3. Miscellaneous
WARNING Never attempt to heat the drum or expose it to any organic solvents such as alcohol, other than the specified refiner; it may generate toxic gas. .........................................................................................................
2AD
CONTENTS
I THEORY AND CONSTRUCTION SECTION
1-1 Specifications 1-1-1 Specifications ................................................................................ 1-1-1 1-2 Handling Precautions 1-2-1 Drum ............................................................................................. 1-2-1 1-2-2 Developer and toner ...................................................................... 1-2-1 1-3 Mechanical Construction 1-3-1 Parts names and their functions .................................................... 1-3-1 1-3-2 Machine cross section ................................................................... 1-3-3 1-3-3 Drive system ................................................................................. 1-3-5 1-3-4 Mechanical construction .............................................................. 1-3-11
II ELECTRICAL SECTION
2-1 Electrical Parts Layout 2-1-1 Electrical parts layout .................................................................... 2-1-1 2-2 Detection of Paper Misfeed 2-2-1 Paper misfeed detection ............................................................... 2-2-1 2-2-2 Paper misfeed detection conditions .............................................. 2-2-2 2-2-3 Original misfeed detection ........................................................... 2-2-14 2-2-4 Original misfeed detection conditions ......................................... 2-2-15 2-3 Operation of the PCBs 2-3-1 Power source PCB ........................................................................ 2-3-1 2-3-2 Engine PCB ................................................................................... 2-3-4 2-3-3 Main PCB ...................................................................................... 2-3-5 2-3-4 Memory copy PCB ........................................................................ 2-3-7 2-3-5 Scanner control PCB ..................................................................... 2-3-9 2-3-6 Scanner motor PCB .................................................................... 2-3-11 2-3-7 CCD PCB .................................................................................... 2-3-12 2-3-8 DF driver PCB ............................................................................. 2-3-13 2-3-9 Operation unit main PCB,operation unit right PCB,and operation unit left PCB ................................................................ 2-3-14 2-3-10 Deck main PCB ........................................................................... 2-3-18
1-1-1
2AD 3-3-2 Paper feed section ........................................................................ 3-3-3 3-3-3 Optical section ............................................................................. 3-3-23 3-3-4 Main charging section ................................................................. 3-3-40 3-3-5 Drum section ............................................................................... 3-3-43 3-3-6 Developing section ...................................................................... 3-3-49 3-3-7 Transfer and separation section .................................................. 3-3-54 3-3-8 Cleaning section .......................................................................... 3-3-57 3-3-9 Fixing section .............................................................................. 3-3-62 3-3-10 Feedshift and duplex section ...................................................... 3-3-79 3-3-11 SRDF section .............................................................................. 3-3-88 3-3-12 Large paper deck section .......................................................... 3-3-101 PCB Initial Settings 3-4-1 Replacing the main PCB ............................................................... 3-4-1 3-4-2 Replacing the main PCB ROMs .................................................... 3-4-2 3-4-3 Adjustment-free variable resisters (VR) ........................................ 3-4-3 Self-Diagnosis 3-5-1 Self-diagnosis ................................................................................ 3-5-1 Troubleshooting 3-6-1 Image formation problems ............................................................ 3-6-1 3-6-2 Paper misfeeds ........................................................................... 3-6-16 3-6-3 PCB terminal voltages ................................................................. 3-6-31 3-6-4 Electrical problems ...................................................................... 3-6-74 3-6-5 Mechanical problems .................................................................. 3-6-98 Appendixes Timing chart No. 1 .................................................................................... 3-7-1 Timing chart No. 2 .................................................................................... 3-7-2 Timing chart No. 3 .................................................................................... 3-7-3 Timing chart No. 4 .................................................................................... 3-7-4 Timing chart No. 5 .................................................................................... 3-7-5 Timing chart No. 6 .................................................................................... 3-7-6 Timing chart No. 7 .................................................................................... 3-7-7 Timing chart No. 8 .................................................................................... 3-7-8 Timing chart No. 9 .................................................................................... 3-7-9 Timing chart No. 10 ................................................................................ 3-7-10 Timing chart No. 11 ................................................................................ 3-7-11 Timing chart No. 12 ................................................................................ 3-7-12 Power source PCB ................................................................................. 3-7-13 Engine PCB 1/2 ...................................................................................... 3-7-14 Engine PCB 2/2 ...................................................................................... 3-7-15 Main PCB 1/5 .......................................................................................... 3-7-16 Main PCB 2/5 .......................................................................................... 3-7-17 Main PCB 3/5 .......................................................................................... 3-7-18 Main PCB 4/5 .......................................................................................... 3-7-19 Main PCB 5/5 .......................................................................................... 3-7-20 Memory copy PCB 1/12 .......................................................................... 3-7-21 Memory copy PCB 2/12 .......................................................................... 3-7-22 Memory copy PCB 3/12 .......................................................................... 3-7-23 Memory copy PCB 4/12 .......................................................................... 3-7-24 Memory copy PCB 5/12 .......................................................................... 3-7-25 Memory copy PCB 6/12 .......................................................................... 3-7-26
3-4
3-5 3-6
3-7
1-1-2
2AD Memory copy PCB 7/12 .......................................................................... Memory copy PCB 8/12 .......................................................................... Memory copy PCB 9/12 .......................................................................... Memory copy PCB 10/12 ........................................................................ Memory copy PCB 11/12 ........................................................................ Memory copy PCB 12/12 ........................................................................ Scanner control PCB 1/4 ........................................................................ Scanner control PCB 2/4 ........................................................................ Scanner control PCB 3/4 ........................................................................ Scanner control PCB 4/4 ........................................................................ Scanner motor PCB ................................................................................ CCD PCB ................................................................................................ DF driver PCB ......................................................................................... Operation unit main PCB 1/2 .................................................................. Operation unit main PCB 2/2 .................................................................. Operation unit right PCB ......................................................................... Operation unit left PCB ........................................................................... Deck main PCB ...................................................................................... Interface PCB ......................................................................................... SRDF connection diagram ...................................................................... General connection diagram ................................................................... SRDF wiring diagram .............................................................................. Large paper deck wiring diagram ........................................................... Optical section wiring diagram ................................................................ General wiring diagram ........................................................................... 3-7-27 3-7-28 3-7-29 3-7-30 3-7-31 3-7-32 3-7-33 3-7-34 3-7-35 3-7-36 3-7-37 3-7-38 3-7-39 3-7-40 3-7-41 3-7-42 3-7-43 3-7-44 3-7-45 3-7-46 3-7-47 3-7-48 3-7-49 3-7-50 3-7-51
1-1-3
2AD
1-1-5
2AD
1-1-1 Specifications
Copier Type Console Copying system Dry, indirect electrostatic system Originals Sheets and books Maximum size: A3/11" 17" Original feed system Fixed Copy paper Drawer and duplex unit: Plain paper (64 80 g/m2) Bypass table: Plain paper (60 160 g/m2) Special paper: Transparencies, tracing paper, colored paper, letterhead and envelopes (only when used as a printer) Note: Use the bypass table for special paper. Copying sizes Maximum: A3/11" 17" Minimum: A6R/5 1/ 2" 8 1/ 2" During duplex copying Maximum: A3/11" 17" Minimum: A5R/5 1/ 2" 8 1/ 2" Magnification ratios Manual mode: 25 400%, 1% increments Auto copy mode: Fixed ratios Metric 1:1 0.1%, 1:4.00/1:2.00/1:1.41/1:1.06/1:0.75/ 1:0.70/1:0.50/1:0.25 Inch 1:1 0.1%, 1:4.00/1:2.00/1:1.29/1:1.21/1:0.78/ 1:0.64/1:0.50/1:0.25 Copy speed At 100% magnification in memory copy mode: A4/11" 81/2": 50 copies/min. A4R/8 1/ 2" 11": 35 copies/min. A3/11" 17": 26 copies/min. B4 (257 x 364 mm)/8 1/ 2" 14": 28 copies/min. When the SRDF is used (at 100% magnification): A4/11" 81/2": 40 copies/min. First copy time 4.5 s or less (A4/11" 81/ 2", 100% magnification, upper drawer, manual copy density control) Warm-up time 180 s or less (room temperature 20C/68F, 65%RH) Paper feed system Automatic feed Capacity: Drawers: 550 sheets Manual feed Capacity: Bypass: 100 sheets Photoconductor OPC (drum diameter 60 mm) Charging system Single positive corona charging Exposure light source Semiconductor laser Exposure scanning system Polygon mirror
1-1-1
2AD Developing system Dry, reverse developing (magnetic brush) Developer: 2-component, ferrite carrier and N29T black toner Toner density control: toner sensor Toner replenishing: automatic from a toner hopper Transfer system Single negative corona charging Separation system Single AC corona charging Fixing system Heat roller Heat source: halogen heaters (main 850 W, sub 850 W) Control temperature: 190C/374F (at normal ambient temperature) Abnormally high temperature protection devices: 140C/284F and 150C/302F thermostats Fixing pressure: 210 N Charge erasing system Exposure by cleaning lamp Cleaning system Cleaning blade and cleaning brush Scanning system Flat bed scanning by CCD image sensor Bit map memory 24 MB (standard) Image storage memory 64 MB (standard) Resolution 600 600 dpi Light source Inert gas lamp Dimensions 627 (W) 748 (D) 1131 (H) mm 2411 /16 " (W) 297/ 16" (D) 449/ 16" (H) Weight 160 kg/352 lbs Floor requirements 1287 mm (W) 748 (D)mm 505/ 16" (W) 297/16 " (D) Functions (1) Self-diagnostics (2) Preheat (3) Automatic copy density control (4) Original size detection (5) Automatic paper selection (6) Automatic magnification selection (7) Enlargement/reduction copy (8) Fixed ratio selection (9) Size zoom mode (10) XY zoom mode (11) Photo mode (12) Duplex copy (13) Margin copy (14) Print page numbers function (15) Split copy (16) Border erasing (17) Sheet copy (18) Transparency backing sheet function (19) Form overlay (20) Combine copy (21) Booklet + cover copy (22) Sort copy (23) Invert copy (24) Mirror image mode
1-1-2
2AD (25) Program copy (26) Setting change mode (27) Job build mode (28) Job reservation function (29) Department control (30) Weekly timer (31) Language selection Power source 120 V AC, 60 Hz, 10 A 220 240 V AC, 50 or 60 Hz, 4.8 A Power consumption 1200 W Options Finisher, key counter,printer unit, additional memory (16 MB/32 MB) and copy tray (for 120 V specifications only). SRDF Original feed system Automatic feed Originals Sheets Original weights Single-sided original mode: 35 160 g/m2 Double-sided original mode: 50 120 g/m2 Original paper Plain paper, thermal paper, art paper, colored paper Original sizes A3 A5R, folio/11" 17" 51/ 2" 8 1/ 2" No. of originals Up to 50 sheets (A3, B4, folio, 11" 17", 81/ 2" 14") Up to 70 sheets (up to A4/11" 81/2") Up to 50 sheets in the auto selection mode Art or thermal paper must be fed individually. Power source Electrically connected to the copier Large paper deck Paper Plain paper (64 80 g/m2) Paper size A4, B5, 11" 81/2" Capacity 3000 sheets (1500 sheets 2) No. of stacks 2 Power source Electrically connected to the copier Type of cassette Universal (to change the paper size, the deck must be adjusted by a service person.)
1-1-3
2AD
1-1-7
2AD
1-2-1 Drum
Note the following when handling or storing the drum. When removing the image formation unit, never expose the drum surface to strong direct light. Keep the drum at an ambient temperature between 20C/4F and 40C/104F and at a relative humidity not higher than 85% RH. Avoid abrupt changes in temperature and humidity. Avoid exposure to any substance which is harmful to or may affect the quality of the drum. Do not touch the drum surface with any object. Should it be touched by hands or stained with oil, clean it. If the machine is left open for more than 5 minutes for maintenance, remove the drum and store it in the drum storage bag (Part No. 78369020).
1-2-1
2AD
1-1-9
E A E
E A E
2AD
8 @ $ # & %
9 !
Figure 1-3-1 1 2 3 4 5 6 7 8 9 0 ! Contact platen Original size indictor lines Operation panel Bypass table Insert guide Support guide Front cover Right cover Upper drawer Length guide tab Width guide tab @ # $ % ^ & * ( ) Lower drawer Large paper deck Deck side cover Drawer Deck front cover Lifts Paper side guides DF original reversing cover Original set indicator Original insertion guides Original table DF opening/closing lever Original ejection cover Paper ejection guide Main switch Left cover Copy tray* Toner cartridge Toner cartridge release lever Image formation unit release button Image formation unit handle Paper transfer unit release lever Paper feed section knob Duplex unit Re-feeding section Duplex unit cover Duplex unit handle Fixing unit Fixing unit handle Fixing knob Fixing unit release lever Handles for transport * Optional for 120 V specifications.
1-3-1
E A E A A E 2AD (MCA) E A A E
E A E
E A E
2AD Metric
284 9
4
A A A A A
/C
3 5
Inch
76
! 0@#
& *
284 9
1 2 3 4 5 6 7 8 9 0 ! @ # $ % ^ & * ( )
Punch mode key Punch mode indicator Staple mode key Staple mode indicator Sorter mode key Sort mode indicator Group mode indicator Brightness adjustment control Data indicator Program key Manual key Add job key Copier/printer switching key Touch panel Numeric keys Stop/clear key Print key Print indicator CA/reset key Auto selection key Auto selection indicator Energy saver key Energy saver indicator Interrupt key Interrupt indicator
Data
Punch
812 14 812 11
4
Staple
812 14 812 11
6
Energy Saver
A A
A A A
Program
Copier/ Printer
Sort Group
Manual
Add job
Stop/ Clear
Interrupt
35
76
! 0@#
Figure 1-3-2 Operation panel
& *
1-3-2
E A E A E A 2AD (MCA) E A A E
2AD
3 2 8 9 6 5 7
4 1
Figure 1-3-3 Machine cross sectioncopier and SRDF 1 2 3 4 5 6 7 8 9 0 ! Paper feed section (page 1-3-11) Main charging section (page 1-3-19) Optical section (page 1-3-22) Developing section (page 1-3-28) Transfer and separation section (page 1-3-39) Cleaning section (page 1-3-43) Charge erasing section (page 1-3-44) Fixing section (page 1-3-46) Feedshift and eject section (page 1-3-52) Duplex section (page 1-3-54) SRDF (page 1-3-60)
1-3-3
2AD
Paper path
1-3-4
2AD
As viewed from the machine front Figure 1-3-5 Drive systemcopier 1 2 3 4 5 6 7 8 9 0 Drive motor gear Idle pulley 63/35 Cleaning drive belt Idle pulley 40/38 Blade thrust gear Cleaning spiral gear Idle pulley 80/26 Drum drive belt Drum drive tension pulley Drum drive pulley ! @ # $ % ^ & * ( ) Gear 35/29 Developing drive gear Gear 31 Gear 24 Gear 20 Registration clutch gear Upper registration roller gear Lower registration roller gear Gear 39/25 Gear 30
1-3-5
2AD Gear 37 Gear 20 Bypass paper feed clutch gear Gear 18 Gear 16 Lower bypass paper feed pulley gear Gear 16 Bypass forwarding pulley gear paper feed motor gear Gear 55/45 Feed clutch 5 gear Gear 30 Feed clutch 4 gear Gear 47 Gear 40 Gear 28 Gear 34 Lower feed roller gear Upper feed roller gear Gear 30 Gear 28 Feed clutch 1 gear Idle pulley 38/23 Paper feed drive belt Idle pulley 31/42 Feed clutch 2 gear Upper paper feed clutch gear Upper paper feed pulley gear Gear 21 Forwarding pulley gear Gear16 Lower paper feed pulley gear Paper feed tension pulley Idle pulley 31/42 Lower paper feed clutch gear Upper paper feed pulley gear Gear 21 Forwarding pulley gear Gear 16 Lower paper feed pulley gear Feed clutch 3 gear Feed roller 3 pulley Feed drive belt Feed idle pulley Tension pulley 10 Feed roller 4 pulley Paper conveying motor gear Idle gear 43 Duplex unit input gear Pulley 63/32 Paper conveying drive belt Pulley 36/32 Idle gear 36/36 Idle gear 30 Gear 26 Paper conveying roller Paper conveying belt Paper conveying pulley Fixing drive gear Idle gear 30 Idle gear 26 Idle gear 26 Gear 19 Pulley 22 Gear 19 Feedshift drive belt Tension pulley 22 Pulley 22 Gear 20/28 Idle gear 29 Idle gear 30 One-way gear Idle gear 20 Eject speed switching clutch gear Gear 26 Idle gear 26 Idle gear 20 Gear 23 Pulley 28 Eject drive belt Tension pulley 28 Eject roller pulley Scanner motor pulley Scanner drive belt Scanner drive pulley Scanner wire drum Scanner wire Scanner wire pulley
' ` 1 2 3 4 5 6 7 8
1-3-6
2AD
1 6
0 7 8 9 ^ ! @ $
2 5 3 4
#
As viewed from machine front
Figure 1-3-6 Drive systemDuplex section 1 2 3 4 5 6 7 8 Duplex joint gear Gear 28 Duplex registration gear 20/30 Gear 26 Switchback roller gear Forwarding drive gear 18 Pulley 22 Forwarding belt 9 0 ! @ # $ % ^ Forwarding pulley 27 Gear 18 Gear 26 Paper conveying pulley 40 Paper conveying drive belt Paper conveying tension pulley Paper conveying pulley 20 Paper conveying pulley 20
1-3-7
2AD
4 9 5 6
3 @ !
^ 0 1
$ & %
As viewed from machine rear Figure 1-3-7 Drive systemSRDF (inside rear of machine) 1 2 3 4 5 6 7 8 9 Original feed motor pulley Pulley 35/22/22 Idle gear 26 Original feed clutch gear DF original feed pulley 28 DF forwarding pulley 20 Tension pulley Original feed drive belt DF forwarding belt 0 ! @ # $ % ^ & * DF registration pulley 28/18 Idle gear 15 Idle gear 20 Switchback gear 18 DF registration drive belt Gear 22/35 Original conveying motor pulley Gear 28 Original conveying drive belt 1
1-3-8
2AD
8 6 7 5 9 1 0 3
4 !
2
As viewed from machine front
Figure 1-3-8 Drive systemSRDF (inside front of machine) 1 2 3 4 5 6 Lower original conveying pulley 25/18 Gear 18/25 Eject gear 18 Middle original conveying pulley 18 Upper original conveying pulley 18 JAM release gear 24 7 8 9 0 ! Joint gear 14 JAM release gear 14 Tension pulley Eject drive belt Conveying drive belt 2
1-3-9
2AD
9 3 $ ) $ 5 % $ & # 4 $ # % 5 $ *
2 $ % 6 5
7 8
@ # $ ^ & ( 5
5 6 0 1 !
As viewed from machine front Figure 1-3-9 Drive systemLarge paper deck
1 2 3 4 5 6 7 8 9 0 ! @ #
Belt 180-6 Paper feed clutch 1 Paper feed clutch 2 Paper conveying clutch Gear 20 Gear 26 Gear 50-20 Gear 35-1-20 Pulley 18 Gear 43-20 Pulley S2M-18 Gear 16 Roller 0.8-20
$ % ^ & * ( )
Pulley 20, gear 32 One-way drum Pulley 18-OW Pulse gear Belt 258 Belt 234 Belt 144 Gear 1.0-24 Lift pulley Left lift belt assembly Right lift belt assembly Paper deck motor gear Pulley 16
1-3-10
2AD
$ 4 6 ^ * % 7 & 5 1 2 8 9 0 # ) 3 3 @ # 1 2 ! # #
Figure 1-3-10 Drawer paper feed and secondary paper feed sections
1-3-11
2AD 1 2 3 4 5 6 7 8 9 0 ! @ # $ % ^ & * ( ) Forwarding pulley Upper paper feed pulley Lower paper feed pulley Upper feed roller Lower feed roller Upper feed guide plate Middle feed guide plate Lower feed guide plate Feed roller 1 Feed roller 2 Feed roller 3 Feed roller 4 Feed pulley Upper registration roller Lower registration roller Upper registration guide Lower registration guide Lower pre-transfer guide Feed guide Drawer lift Lift operation plate Upper paper feed clutch (PFCL-U) Lower paper feed clutch (PFCL-L) Feed clutch 1 (FCL1) Feed clutch 2 (FCL2) Feed clutch 3 (FCL3) Feed clutch 4 (FCL4) Feed clutch 5 (FCL5) Registration clutch (RCL) Upper paper switch (PSW-U) Lower paper switch (PSW-L) Upper lift limit switch (LICSW-U) Lower lift limit switch (LICSW-L) Paper feed switch 1 (PFSW1) Paper feed switch 2 (PFSW2) Paper feed switch 3 (PFSW3) Paper feed switch 4 (PFSW4) Feed switch (FSW) Registration switch (RSW) Upper paper length switch (PLSW-U) Lower paper length switch (PLSW-L) *Upper paper width switch (PWSW-U) *Lower paper width switch (PWSW-L)
1-3-12
2AD Each drawer consists of a lift driven by the lift motor and other components. Each drawer can hold up to 550 sheets of paper. Paper is fed from the drawer by the rotation of the forwarding pulley and upper paper feed pulley. The lower paper feed pulley prevents multiple sheets from being fed at one time, via the torque limiter.
CN13-4 CN13-7 CN8-B11 CN13-10 CN13-13 CN8-B2 CN13-1 CN12-A2 CN8-B9 CN12-A4
RCL
LICSW-U
PSW-U
FCL2
PFCL L PFSW3
PFSW4
Figure 1-3-11
1-3-13
2AD
Image ready Print key FCL4 FSW RSW FCL5 RCL PFM DM PFCL-U FCL2 PFSW2 FCL1 PFSW1 163 ms 28 ms 35 ms 250 ms 100 ms 50 ms 58 ms 100 ms 74 ms 80 ms
174 ms
35 ms
A B C
Auto copy density control, copy paper: A4/11" 81/2", magnification ratio 100%
1-3-14
2AD A When the print key is pressed, the paper feed motor (PFM) turns on, and 250 ms later the drive motor (DM) turns on to start drive for the paper feed section. B 100 ms after the print key is pressed, the upper paper feed clutch (PFCL-U) turns on, and the upper and lower paper feed pulleys rotate to start the primary paper feed. C 50 ms after the upper paper feed clutch (PFCL-U) turns on, feed clutch 2 (FCL2) turns on, and feed roller 2 rotates. D 28 ms after the leading edge of the paper turns paper feed switch 2 (PFSW2) on, feed clutch 1 (FCL1) turns on, and feed roller 1 to rotates. E 163 ms after paper feed switch 2 (PFSW2) turns on, the upper paper feed clutch (PFCLU) turns off. F 174 ms after the leading edge of the paper turns paper feed switch 1 (PFSW1) on, feed clutch 4 (FCL4) turns on, and the lower feed roller rotates at high speed to create slack in the paper before registration. G 58 ms after the trailing edge of the paper turns paper feed switch 2 (PFSW2) turns off, feed clutch 2 (FCL2) turns off. H 35 ms after the leading edge of the paper turns the registration switch (RSW) on, feed clutches 1 and 4 (FCL1 and FCL4) turn off. I 74 ms after image ready signal turn on, the registration clutch (RCL) turns on, causing the upper and lower registration rollers to rotate to start secondary paper feed. Simultaneously, feed clutch 5 (FCL5) turns on and the lower feed roller rotates at low speed. J 100 ms after the trailing edge of the paper turns the feed switch (FSW) off, feed clutch 5 (FCL5) turns off. K 80 ms after the trailing edge of the paper turns the registration switch (RSW) off, the registration clutch (RCL) turns off.
1-3-15
0 ! 9 6 5 7 1 4 3 8 2 #
Figure 1-3-12 Bypass paper feed section 1 2 3 4 5 6 7 8 Bypass table Bypass upper guide Bypass lower guide Bypass stopper Bypass friction plate Bypass forwarding pulley Bypass upper paper feed pulley Bypass lower paper feed pulley 9 0 ! @ # $ Bypass paper feed clutch (BYPPFCL) Bypass solenoid (BYPSOL) Bypass paper switch (BYPPSW) Bypass paper length switch (BYPPLSW) Bypass paper width switch (BYPPWSW) Bypass table extended detection switch (BYPEDSW)
The bypass table can hold up to 100 sheets of paper at one time. When the start key is pressed, the bypass solenoid (BYPSOL) turns on, unlocking the bypass stopper and lowering the bypass forwarding pulley until it comes into contact with the paper. This conveys paper placed on the bypass table to the bypass upper and lower paper feed pulleys. The bypass paper feed clutch (BYPPFCL) then turns on, transmitting the drive motor (DM) drive to these pulleys to start primary paper feed. The bypass lower paper feed pulley rotates opposite to the paper feed direction so that the torque limiter prevents multiple sheets from being fed at one time.
1-3-16
2AD
CN14-A8 CN14-A4 CN14-A7 CN8-B11 RCL BYPPSW BYPSOL BYP PFCL RSW FSW FCL5 FCL4
Image ready
Print key FSW RSW FCL5 RCL PFM DM BYPSOL BYPPFCL A B 250 ms 100 ms 300 ms 90 ms 200 ms 115 ms 65 ms 100 ms 74 ms 80 ms
D E F
Auto copy density control, copy paper: A5R/51/2" 81/2", magnification ratio 25%
1-3-17
2AD A When the print key is pressed, the paper feed motor (PFM) turns on, and 250 ms later the drive motor (DM) turn on to start drive for the paper feed section. B 100 ms after the print key is pressed, the bypass solenoid (BYPSOL) turns on. The bypass stopper is then unlocked, and the bypass forwarding pulley lowers to forward the paper. C 300 ms after the bypass solenoid (BYPSOL) turns on, the bypass paper feed clutch (BYPPFCL) turns on, and the upper and lower bypass paper feed pulleys rotate to start primary paper feed. D 115 ms after the leading edge of the paper turn the feed switch (FSW) on, feed clutch 5 (FCL5) turns on, and the lower feed roller rotates at low speed to create slack in the paper before registration. E 200 ms after the feed switch (FSW) turns on, the bypass paper feed clutch (BYPPFCL) turns off. F 90 ms after feed clutch 5 (FCL5) turns on, the bypass solenoid (BYPSOL) turns off. G 65 ms after the leading edge of the paper turns the registration switch (RSW) on, feed clutch 5 (FCL 5) turns off. H 74 ms after the image ready signal turns on, the registration clutch (RCL) turns on, and the upper and lower registration rollers rotate to start secondary paper feed. Simultaneously, feed clutch 5 (FCL5) turns on and lower feed roller rotates at low speed. I 100 ms after the trailing edge of the paper turns the feed switch (FSW) off, feed clutch 5 (FCL5) turns off. J 80 ms after the trailing edge of the paper turns the registration switch (RSW) off, the registration clutch (RCL) turns off.
1-3-18
2AD (2) Main charging section The main charging section consists of the drum and the main charger assembly. The main charger assembly charges the drum so that a latent image is formed on the surface, the charger grid ensuring the charge is applied uniformly.
Main charger assembly Main charger grid Tungsten wire
Drum
Figure 1-3-14
1-3-19
2AD
! 0 3 1 6 4 9 7 5 8
2
Figure 1-3-15 1 2 3 4 5 Main charger front housing Main charger rear housing Main charger front lid Main charger rear lid Main charger shield Main charger 6 7 8 9 0 ! Tungsten wire Charger spring Charger terminal Charger pin Main charger grid Grid tension plate
MC
Figure 1-3-16
1-3-20
2AD
360 ms
300 ms 290-30000 ms
B
1 2
Auto copy density control, copy paper: A4/11" 8 / ", magnification ratio 100%
Timing chart1-3-3 Main charging A When the print key is pressed, the paper feed motor (PFM) turns on. B 520 ms after the paper feed motor (PFM) turns on, main charging (MC REM) starts. C 300 ms after cooling fan motor 1 (CFM1) turns off, main charging (MC REM) is completed.
1-3-21
2AD (3) Optical section The optical section consists of the scanner, mirror frame and image scanning unit for scanning and the laser scanner unit for printing.
6 9 4 $ 5 7 2 3 ! 1 @ # 8 0
Figure 1-3-17 Optical section 1 2 3 4 5 6 7 Scanner Mirror frame Mirror 1 Mirror 2 Mirror 3 Exposure lamp (EL) Reflector 8 9 0 ! @ # $ Image scanning unit Lens Optical rail Laser scanner unit (LSU) CCD PCB (CCDPCB) Scanner motor (SM) Scanner home position switch (SHPSW)
1-3-22
2AD Original scanning The original image is illuminated by the exposure lamp (EL) and scanned by the CCD PCB (CCDPCB) in the image scanning unit via the three mirrors, the reflected light being converted to an electrical signal. The scanner and mirror frame travel to scan on the optical rails on the front and rear of the machine to scan from side to side. The speed of the mirror frame is half the speed of the scanner. When the SRDF is used, the scanner and mirror frame stop at the DF original scanning position to start scanning.
Original SHPSW CCDPCB SM EL
CN2-1 CN2-6
CN4-2
CN2-1
CN4-1 CN4-14
CN1-1 CN1-14
SCPCB
CN7-1 CN7-13
MPCB
CN1-1 CN1-140
EPCB
CN7-1 CN7-2
CN9-1 CN9-4
1-3-23
2AD
Print key 410 P Fwd. rotation SM Rev. rotation SHPSW 414 P 9921 P
110 P
FVSYNC signal A B C D
Manual copy density control, copy paper: A3/11" 17", magnification ratio 100%
Timing chart 1-3-4 Scanner operation A When the print key is pressed, the scanner motor (SM) reverses for 410 pulses and then rotates forward. B 414 pulses after the scanner motor rotates forward, the FVSYNC signal turns on for 9921 pulses for scanning. C The scanner motor (SM) reverses to return the scanner to the home position. D 110 pulses after the scanner home position switch (SHPSW) turns on, the scanner motor (SM) turns off, and the scanner stops at its home position.
1-3-24
2AD Image printing The image data scanned by the CCD PCB (CCDPCB) is processed on the main PCB (MPCB) and transmitted as image printing data to the laser scanner unit (LSU). By repeatedly turning the laser on and off, the laser scanner unit forms a latent image on the drum surface. Laser scanner unit
Collimator lenses Laser diodes (LD) LD control PCB BD sensor mirror Lens 1 Lens 3 Lens 2 Polygon mirror Polygon motor (PM) Beam spritter
Figure 1-3-19
1-3-25
2AD
5 6
1 2
3 5
8 9 0 5
Drum
Figure 1-3-20 Laser scanner unit (2) 1 Laser diodes: Generate the laser beams that form the latent image on the drum. 2 Collimator lenses: Collimate the diffused laser beams emitted from the laser diodes into cylindrical beams. 3 Beam splitter: Refracts the laser beam emitted from one of the laser diodes so that it becomes parallel to the other laser beam, and sends those two beams to lens 1. 4 Polygon mirror: 6-faced mirror that rotates at approximately 29527 rpm. Each face reflects the laser beams toward the drum in the horizontal (main) scan direction. The motion of the beams across the drum forms one scan line. 5 Lenses 1, 2, 3 and 4: Maintain scanning speed across the drum and beam diameters constant. These lenses also correct the vertical alignment of the polygon mirror so that the focal plane of the laser beams are always on the drum. 6 Object mirror: Reflects the laser beams onto the drum surface. 7 BD sensor mirror: Directs a laser beam to the BD sensor to generate the horizontal sync signal. 8 Cylindrical correcting lens: Corrects for the deviation of the laser beam reflected by the BD sensor mirror. 9 BD sensor: Detects the laser beam reflected by BD sensor mirror, and sends the detection signal to the main PCB (MPCB). The main PCB (MPCB) uses this signal to determine the horizontal scanning signal timing. 0 Glass dust filter: Prevents dust from entering the unit.
1-3-26
2AD The dimensions of the laser beam are as shown in Figure 1-3-19.
70 m
65 m
Figure 1-3-21 Scanning in the main direction is provided by the rotating polygon mirror, while scanning in the auxiliary direction is provided by the rotating drum, forming a static latent image on the drum. The static latent image of the letter A, for example, is formed on the drum surface as shown in Figure 1-3-22. Electrical charge is dissipated on the area of the drum surface irradiated by the laser. The focal point of the laser beam is moved line by line, and adjacent lines slightly overlap each other.
Main scanning direction
: laser beam is on
Figure 1-3-22
1-3-27
2AD (4) Developing section The developing section consists of the developing unit and the toner recycling assembly.
Developing unit Toner sub hopper
Figure 1-3-23 Developing section The developing unit consists of the developing roller where a magnetic brush is formed, the doctor blade and the developing spirals that agitate the developer. The toner recycling assembly consists of the toner main and sub-hoppers. In t he main hopper new toner from the toner cartridge is mixed with residual toner recovered from the cleaning section. The mixture is conveyed by the sub-hopper to the developing unit. The amount of toner in the main hopper is monitored by the toner level detection sensor (TLDS).
1-3-28
2AD
Toner cartridge paddle Toner cartridge spiral Toner cartridge
Toner recycle paddle B Toner hopper lockup sensor Toner recycle spiral Toner level sensor Toner recycle paddle A Cleaning spiral Cleaning unit
Toner feed motor Main hopper spiral Developing unit Toner sub hopper Toner main hopper Sub hopper spiral Toner recycle motor
Toner flow
Figure 1-3-24
Toner recycling
1-3-29
2AD Formation of magnetic brush The developing roller consists of a magnet roller with five poles and a sleeve roller. Rotation of the sleeve roller around the magnet roller entrains developer, which in turn forms a magnetic brush at pole N1 on the magnet roller. The height of the magnet brush is regulated by the doctor blade; the developing result is affected by the position of the poles on the magnet roller and the position of the doctor blade. A developing bias voltage generated by the high-voltage transformer (HVTPCB) is applied to the developing roller to provide image contrast.
4
A
6 7
Magnetic poles on the developing roller S2 74.5 85.5 N3 N1 59
2 5 1 3
N2
A: Distances beteen the doctor blade and developing roller: 0.53 0.05 mm
830 104 T 630 104 T 450 104 T 860 104 T 700 104 T
Figure 1-3-25 1 2 3 4 Developing unit housing Developing roller Toner sensor (TNS) Doctor blade
1-3-30
2AD
TRM
TFM
CN2-A10
CN2-B11 CN2-B9
TNS
DB REM DB CONT 24 V DC
Figure 1-3-26 Developing section block diagram Toner density is detected by the toner sensor (TNS). The sensor section of the toner sensor detects the ratio of toner to carrier in the developer near it and converts it into a voltage. As more toner is used, the ratio of toner to carrier decreases, increasing the toner sensor output voltage. When the ratio drops below the specified value, the increase in toner sensor output voltage triggers toner replenishing. When toner is added and the ratio of toner to carrier returns to normal, the toner sensor output voltage drops to the point where toner replenishing stops.
1-3-31
2AD Toner density control Toner density control is conducted using the TARGET value as the reference which is the toner sensor initial output value set by maintenance item U130 when developer is loaded for the first time.
Toner being replenished message Toner sensor output voltage (V) Toner empty detection level Toner empty reset level Toner feed start level (TARGET by U130) Toner feed stop level Toner request message (Toner cartridge to be replaced.)
Copying
A B
Figure 1-3-27
C D E F
H I J
A When the toner sensor output voltage exceeds the toner feed start level, the toner feed motor (TFM) and the toner recycle motor (TRM) operate intermittentlyon for 0.5 s and off for 1.5 s, and on for 1.0 s and off for 1.0 s, respectivelyto replenish toner. B As toner is replenished, the toner sensor output voltage drops below the toner feed stop level and replenishing stops. C Both the toner feed motor (TFM) and toner recycle motor (TRM) operate intermittently on for 0.5 s and off for 0.5 sto replenish toner until the toner sensor output voltage reaches the toner empty reset level after exceeding the toner feed start level. D The toner feed motor (TFM) and toner recycle motor (TRM) operate intermittentlyon for 1.0 s and off for 1.0 s, and on for 1.5 s and off for 0.5 s, respectivelyto replenish toner until the toner sensor output voltage reaches the toner empty detection level after exceeding the toner feed reset level E When the toner sensor output voltage exceeds the toner empty detection level after toner replenishing is carried out, the toner being replenished message appears. Both the toner feed motor (TFM) and toner recycle motor (TRM) then operate intermittentlyon for 1.5 s and off for 0.5 sfor 1 min. for aging. If the voltage fails to fall to the toner empty reset level, the toner request message appears.
1-3-32
2AD F When the toner sensor output voltage drops to the toner empty reset level, the toner being replenished message disappears, and both the toner feed motor (TFM) and toner recycle motor (TRM) operates intermittentlyon for 0.5 s and off for 0.5 sto replenish toner. G When toner is replenished, the toner sensor output voltage drops below the toner feed stop level and replenishing stops. H After the toner cartridge is replaced, both the toner feed motor (TFM) and toner recycle motor (TRM) operate intermittentlyon for 1.5 s and off for 0.5 sto replenish toner. I When the toner sensor output voltage drops to the toner feed stop level, the toner request message disappears. Both the toner feed motor (TFM) and toner recycle motor (TRM) then operate intermittentlyon for 1.0 s and off for 1.0 sto replenish toner. J When toner is replenished, the toner sensor output voltage drops to the toner feed stop level and replenishing stops.
1-3-33
2AD Correcting toner feed start level The toner density is subject to humidity changes and the total time the drive motor has been on. To maintain the toner density constant, the toner feed start level is corrected based on the absolute humidity and the total drive motor time. Correction based on the absolute humidity
Correction at the toner feed start level (V) 0.74 C D
B 0 0.16 0 3.09 10.8 A Maintenance item U130 performed. 35.9 Absolute humidity (g/m3)
Figure 1-3-28
A When maintenance item U130 is carried out for initial developer setting, the toner sensor control voltage (CONTROL) is set so that the toner sensor outputs 2.01 V when the absolute humidity is 10.8 g/m3. B When the absolute humidity is between 0 and 10.8 g/m3, the toner feed start level is decreased with the absolute humidity so that the toner sensor output voltage drops. C When the absolute humidity is between 10.8 and 35.9 g/m3, the toner feed start level is increased with the absolute humidity so that the toner sensor output voltage rises. D When the absolute humidity exceeds 35.9 g/m3, the toner feed start level is increased by 0.74 V to regulate the toner sensor output.
1-3-34
2AD Computing the absolute humidity The external humidity sensor (EHUMSENS) and external temperature thermistor (ETTH) are located on the humidity sensor PCB (HUMPCB). The external humidity sensor (EHUMSENS) converts the relative humidity detected by the humidity sensing element into a voltage and sends it to the engine PCB (EPCB). The main PCB (MPCB)computes the absolute humidity based on this EHUMSENS signal and the temperature (ETTH signal) detected by the external temperature thermistor (ETTH).
EPCB HUMPCB ETTH 4 3 Humidity sensing element 2 EHUMSENS 1 5V CN5-A4 EHUMSENS CN5-A3 ETTH GND CN5-A1 CN5-A2
Figure 1-3-29
1-3-35
2AD Correction based on the total drive motor time The toner feed start level is also corrected based on the total time the drive motor (DM) has been on from execution of maintenance item U130, so that the toner sensor output is regulated properly.
Correction at the toner feed start level (V)
E
0.76
D C B
10
30
50
150
A When maintenance item U130 is carried out for initial developer setting, the total drive motor time is cleared and the correction for the toner feed start level is reset to 0. B When the total drive time reaches 10 hours, the toner feed start level is corrected with a constant value of 0.24 V. C When the total drive time reaches 30 hours, the toner feed start level is corrected with a constant value of 0.36 V. D When the total drive time reaches 50 hours, the toner feed start level is corrected with a constant value of 0.46 V. E When the total drive time exceeds 150 hours, the toner feed start level is corrected with a constant value of 0.76 V.
1-3-36
2AD Toner level detection The toner level in the toner main hopper is monitored by the toner level detection sensor (TLDS). It converts the presence or absence of toner in the toner main hopper into a voltage and sends it to the main PCB (MPCB), which triggers a message to request the toner cartridge to be replaced before the recycled toner ratio in the toner main hopper reaches a significant level.
Toner request message Toner empty detection Toner empty detection reactivated. reactivated. Toner cartridge to be U 130 performed. replaced. Toner empty detection Toner empty detection ignored. ignored. TFM: on 1 min. 5 min. 10 s Toner feed motor (TFM) 4.5 V Toner level detection sensor output voltage 0.5 V 10 s 10 s
Figure 1-3-31 Toner level detection A When the toner level detection sensor (TLDS) output voltage drops below 0.5 V while the toner feed motor (TFM) is on, the toner motor drive time starts to be counted. B If the toner level detection sensor (TLDS) output voltage remains below 0.5 V for 10 s, the toner request message appears. Note: When the toner request message is displayed under these conditions, the available copy mode and the number of copies that can be made are restricted as set in maintenance item U258 (see page 3-2-74). C Toner empty detection is ignored for 1 min. (the toner feed motor on time) after the toner cartridge has been replaced. If the toner level detection sensor (TLDS) output remains at 4.5 V or above for 10 s, toner empty detection is reactivated. D Toner empty detection is ignored for 5 min. (the toner feed motor on time) after maintenance item U130 has been performed for developer initial setting. If the toner level detection sensor (TLDS) output remains at 4.5 V or above for 10 s, toner empty detection is reactivated.
1-3-37
2AD Toner hopper lockup detection The amount of recycled toner in the toner main hopper is monitored by the toner hopper lockup sensor (TLS). It converts the presence or absence of toner in the toner main hopper into a voltage and sends it to the main PCB, which prevents toner main hopper lockup as the amount of the recycled toner in the hopper increases.
Toner feed start level Toner feed stop level Toner recycle motor 1 min
Figure 1-3-32 Toner hopper lockup detection A When the toner hopper lockup sensor (TLS) output voltage is below 0.5 V, toner is replenished to control toner density. B When the toner hopper lockup sensor (TLS) output voltage exceeds 4.5 V while toner sensor output voltage is below the toner feed start level, toner is not replenished. C When the toner sensor output voltage is over the toner feed start level while the toner hopper lockup sensor (TLS) output level is over 4.5 V, the toner feed motor (TFM) does not operate, while the toner recycle motor (TRM) operates continuously. D When the toner hopper lockup sensor (TLS) output voltage is over 4.5 V, the on-time of the toner recycle motor (TRM) is counted. When the continuous on-time exceeds 1 min., C740 (toner hopper problem) is displayed.
1-3-38
Figure 1-3-33
The transfer and separation section consists of the transfer charger assembly and drum separation claws. The transfer charger assembly consists of the transfer charger that applies a high voltage to transfer the toner image from the drum surface onto the paper, and the separation charger that helps the paper separate from the drum surface. In the transfer charger, a high voltage generated by the high-voltage transformer PCB (HVTPCB) is applied to the both ends of the tungsten wire. The separation charger uses the AC voltage applied from the high-voltage transformer PCB to neutralize the residual charge on the paper after the transfer process. The paper can then separate from the drum under its own weight. The separation claws ensure that the paper separates reliably from the drum.
1-3-39
2AD
1-3-40
2AD Charger wire cleaning The charger wires are cleaned by the transfer charger cleaning pad and separation charger cleaning pad traveling along each wire. The pads are placed on a slider which moves back and forth along the charger cleaning spiral as the spiral is turned by the charger cleaning motor (CCM). The two shield cleaning sponges travel along the transfer charger shield, cleaning the inside of the shield.
6 4 7 3 # 5 8 ! 0 9 @ $
Figure 1-3-35 1 2 3 4 5 6 7 Transfer charger front housing Transfer charger rear housing Transfer charger front lid Transfer charger rear lid Transfer charger shield Separation guide Tungsten wire for transfer
Transfer charger assembly 8 9 0 ! @ # $ Tungsten wire for separation Transfer charger cleaning pad Separation charger cleaning pad Shield cleaning sponges Charger cleaning pad slider Charger cleaning spiral Charger cleaning motor (CCM)
1-3-41
2AD
Image ready Secondary paper feed start Secondary paper feed end Print key CFM1 ESW 520 ms MC REM PFM SC REM 700 ms RSW RCL TC REM 74 ms 210 ms 80 ms 270 ms 300 ms 290-30000 ms 360 ms
D
1 2
Auto copy density control, copy paper: A4/11" 8 / ", magnification ratio 100%
When the print key is pressed, the paper feed motor (PFM) turns on. 700 ms after the paper feed motor (PFM) turns on, separation charging (SC REM) starts. 210 m after the registration clutch (RCL) turn on to start secondary paper feed, transfer charging (TC REM) starts. 270 ms after the trailing edge of the paper turns the registration switch (RSW) off, transfer charging (TC REM) ends. 290 to 30000 ms after the main charging (MC REM) ends, the paper feed motor (PFM) turns off and separation charging (SC REM) ends.
1-3-42
2AD (6) Cleaning section The cleaning section consists of the cleaning blade and brush that remove residual toner from the drum surface after the transfer process, and the cleaning spiral that carries the residual toner back to the toner recycling assembly.
Figure 1-3-36 Cleaning section 1 2 3 4 5 Drum Cleaning blade Cleaning brush Cleaning spiral Lower cleaning seal
1-3-43
2AD (7) Charge erasing section The cleaning lamp (CL) consists of 36 LEDs which remove residual charge from the drum surface.
Cleaning lamp
CN2-A2
CL REM
CL
Drum EPCB
Figure 1-3-38
1-3-44
2AD
A B
Auto copy density control, copy paper: A4/11" 81/2", magnification ratio 100%
Charge erasing
When the print key is pressed, the paper feed motor (PFM) turns on. 50 ms after the paper feed motor (PFM) turns on, the cleaning lamp (CL) lights to remove the residual charge from the drum surface after the residual toner is removed by the cleaning section. 600 ms after the paper feed motor (PFM) turns off, the cleaning lamp (CL) turns off.
1-3-45
1 @ !
5 3 #
4 0
7 $
9 8 6
Fixing section 8 9 0 ! @ # $ Fixing heater M (H1) Fixing heater S (H2) Eject switch (ESW) Fixing unit thermostat 1 (TH1) Fixing unit thermostat 2 (TH2) Fixing unit thermistor (FTH) Press roller separation claws
Figure 1-3-39
1 2 3 4 5 6 7
Fixing unit upper cover Fixing unit front guide Fixing unit upper guide Fixing unit lower left guide Heat roller Press roller Heat roller separation claws
1-3-46
2AD The fixing section consists of the parts shown in Figure 1-3-39. When paper reaches the fixing section after the transfer process, it passes between the press roller and heat roller, which is heated by fixing heaters M or S (H1 or H2). Pressure is applied by the pressure springs so that the toner on the paper is melted, fused and fixed onto the paper. When the fixing process is completed, the paper is separated from the heat roller by its separation claws and is ejected from the copier to either the eject section or duplex section.
TH2 PRY
TH1
CN4-4 H1 REM
H2 REM
CN4-5
CN3-B8 EPCB
CN6-7
Figure 1-3-40
CN6-8
CN3-B7
5 V DC
FTH
1-3-47
5 4
1 3 2
Figure 1-3-41 Heating the heat roller and detecting temperature 1 2 3 Heat roller Fixing heater M (H1) Fixing heater S (H2) 4 5 6 Fixing unit thermostat 1 (TH1) Fixing unit thermostat 2 (TH2) Fixing unit themistor (FTH)
The heat roller is heated by fixing heaters M or S (H1 or H2) inside it; its surface temperature is detected by the fixing unit thermistor (FTH) and is regulated by the fixing heaters turning on and off. If the fixing section becomes abnormally hot, either the fixing unit thermistor detects it or fixing unit thermostat 1 or 2 (TH1 or TH2) operates, in each case, shutting the power to the fixing heaters off.
1-3-48
Copying enabled
120 s MSW 2s PRY H1 H2 Charger wire cleaning CCM 3s DM 200 ms PCM 270 ms CL 50 ms DB REM CFM1 PCFM IFFM PM 1s Half speed Full speed Half speed 600 ms 176 s
A B
C D E
Aging end
B C
2s after the main switch (MSW) is turned on, the power relay (PRY) and fixing heater M (H1) turn on to heat the heat roller. The charger cleaning motor (CCM) also turns on to clean the charger wire, and cooling fan motor 1 (CFM1) rotates at half speed. 1 s after fixing heater M (H1) turns on, the polygon motor (PM) in the laser scanner unit turns on. When the fixing temperature reaches 175C/347F, the copier enters primary stabilization. 50 ms later the cleaning lamp (CL) and developing bias (DB REM) turn on and primary stabilization starts. 200 ms after the cleaning lamp (CL) turns on, the drive motor (DM) turns on.
1-3-49
2AD E 270 ms after the drive motor (DM) turns on, the paper conveying motor (PCM), paper conveying fan motor (PCFM) and image formation section fan motor (IFFM) turn on and cooling fan motor 1 (CFM1) rotates at full speed. When the fixing temperature reaches 190C/374F, the copier enters secondary stabilization. Fixing heater M (H1) is turned on and off to keep the fixing temperature at 190C/374F and aging starts. 176 s after the power relay (PRY) turns on or 120 s after the copier enters secondary stabilization (whichever event occurs first), copying is enables. 3 s after copying is enabled, the drive motor (DM), paper conveying motor (PCM) and image formation section fan motor (IFFM) turn off, and aging ends. Cooling fan motor 1 (CFM1) rotates at half speed. 600 ms after aging ends, the cleaning lamp (CL), developing bias (DB REM) and paper conveying fan motor (PCFM) turn off.
G H
Fixing control temperature correction Depending on the ambient temperature, the fixing control temperature is corrected as follows. Table 1-3-1 Copy setting Correction for low ambient temperature (Ambient temperature: 17C/ 62.6F or below) Correction for high ambient temperature (Ambient temperature: 37C/ 98.6F or higher) Paper feed from upper and lower drawers, bypass table and large paper deck Continuous copying of 100 or less sheets in duplex copy mode Fixing control temperature 195C/383F (5C/9F higher)
Fixing heater M or S (H1 or H2) is turned on for 5 s from the start of the copying operation so that the fixing control temperature becomes 195C/383F (5C/9F higher).
1-3-50
2AD Paper separation Paper is separated in the fixing section by the separation claws as shown in Figure 1-342.
Heat roller
1-3-51
2AD (9) Feedshift and eject section The feedshift and eject section consists of the parts shown in Figure 1-3-43. When fixing is complete, the conveying path is switched by the feedshift guide to eject the paper to either the copy tray or duplex unit.
3 4
( #
5 6
7 $
* @
^ % & 9 0 !
Figure 1-3-43 1 2 3 4 5 6 7 8 9 0
Feedshift and eject section ! @ # $ % ^ & * ( Lower feedshift roller Feedshift pulley Left switchback eject guide Right middle switchback eject guide Right switchback feed roller Left switchback feed roller Lower right switchback eject guide Feedshift switch (FSSW) Switchback eject switch (SBESW)
Eject roller Eject pulley Upper eject guide Feedshift guide Upper right feedshift guide Right feedshift roller Left feedshift roller Lower right feedshift guide Lower left feedshift guide Lower feedshift guide
1-3-52
2AD
CN3-A8 CN3-A9
CN3-B9
EPCB
Figure 1-3-44
1-3-53
2AD (10) Duplex section In duplex copy mode, the paper copied onto the first face (rear face) is sent to the duplex section for side registration and switchback, and refeed for copying onto the second face (front face).
3 $
@ 8 0
2 # 5 % 7
^ 9
Figure 1-3-45
& !
Duplex section Duplex eject roller Duplex eject pulley Side registration guides Switchback feedshift guide Stock switch (STKSW) Duplex registration switch (DUPRSW) ^ Duplex paper conveying switch (DUPPCSW) & Duplex eject switch (DUPESW) 0 ! @ # $ %
1 2 3 4 5 6 7 8 9
Duplex forwarding pulley Upper refeed guide Paper tapping guide Refeed pulley Switchback roller Duplex upper registration roller Duplex lower registration roller Duplex conveying roller Duplex conveying pulley
1-3-54
2AD When the paper is sent to the duplex section, the duplex paper tapping solenoid (DUPPTSOL) lowers, which forwards the paper by means of the rotation of the duplex forwarding pulley until it is caught by the switchback roller. In duplex copy mode, the switchback feedshift solenoid (SBFSSOL) turns on to operate the switchback feedshift guide. The paper is then sent to the duplex paper conveying section by the rotation of the switchback roller. During switchback ejection, the paper is conveyed to the feedshift and eject section and ejected with the copied face down.
5 2
Figure 1-3-46 1 2 3 4 5
Duplex forwarding pulley Switchback feedshift guide Paper tapping guide Refeed pulley Switchback roller
1-3-55
2AD
EPCB CN10-10 CN10-12 CN10-14 CN10-1 CN10-5 SRM SRHPSW CN9-7 CN9-16 CN10-8 CN9-11 CN9-12 DUPESW CN9-8 DUP PCSW DUP PTSOL
SBFSSOL1 SBFSSOL2
1-3-56
30 ms 80 ms 60 ms 12 P
74 ms
D E
100% magnification
A 74 ms after the image ready signal turns on during copying onto the first face (back), the registration clutch (RCL) turns on to start secondary paper feed. B 1160 ms after the registration clutch (RCL) turns on, the feedshift solenoid (FSSOL) turns on, operating the feedshift guide to switch the paper path to the duplex unit. C When the leading edge of the paper turns the eject switch (ESW) on, the switchback feedshift solenoid (SBFSSOL) turns on, operating the switchback guide to switch the paper path to the duplex unit conveying section. D 60 ms after copying onto the first face (back) is competed and the trailing edge of the paper turns the feedshift switch (FSSW) off, the side registration motor (SRM) rotates forward for 12 pulses for side registration. At the same time, the duplex paper tapping solenoid (DUPPTSOL) turns on, and the paper tapping guide lowers to hold down the trailing edge (leading edge during refeed) of the paper that was conveyed to the duplex section. E 30 ms after the duplex paper tapping solenoid (DUPPTSOL) turns on, the duplex forwarding solenoid (DUPFWDSOL) turns on, operating the duplex forwarding pulley to forward the paper until it is caught by the switchback roller. F 80 ms after the stock switch (STKSW) turns off, the duplex tapping solenoid (DUPPTSOL) and duplex forwarding solenoid (DUPFWDSOL) turn off.
1-3-57
2AD
1160 ms FSSOL 360 ms SBFSSOL Fwd. rotation SRM Rev. rotation SRHPSW DUPRSW DUPPCSW DUPESW 232 ms FCL1 FCL4 FSW RSW FCL5 RCL ESW A B C D E F G
1/ 2",
500 ms
500 ms
500 ms 5P
30 ms 35 ms
74 ms
100 ms 80 ms
I J
K L
100% magnification
Refeed
A 232 ms after the leading edge of the paper turns the duplex eject switch (DUPESW) on, feed clutch 1 (FCL1) turns on and feed roller 1 rotates. B 30 ms after the leading edge of the paper turns the feed switch (FSW) on, feed clutch 4 turns on and the lower feed roller rotates at high speed to create slack in the paper before registration. C 35 ms after the leading edge of the paper turns the registration switch (RSW) on, feed clutch 1 (FCL1) and feed clutch 4 (FCL4) turn off. D 74 ms after feed clutch 4 (FCL4) turns off, the registration clutch (RCL) turns on, and the upper and lower registration rollers rotate to start secondary paper feed. At the same time feed clutch 5 (FCL5) turns on and the lower feed roller rotates at low speed. E 100 ms after the trailing edge of the paper turns the feed switch (FSW) off, feed clutch 5 (FCL5) turns off. F 80 ms after the trailing edge of the paper turns the registration switch (RSW) off, the registration clutch (RCL) turns off. G 1160 ms after the registration clutch (RCL) turns on, the feedshift solenoid (FSSOL) turns off. H 360 ms after copying onto the second face (front) is completed and the eject switch (ESW) turns off, the switchback feedshift solenoid (SBFSSOL) turns off. I 500 ms after the switchback feedshift solenoid (SBFSSOL) turns off, the side registration motor (SRM) reverses to move the side registration guides outwards.
1-3-58
2AD J When the side registration home position switch (SRHPSW) turns on, the side registration motor (SRM) turns off. K 500 ms after the side registration home position switch (SRHPSW) turns on, the side registration motor (SRM) rotates forward to move the side registration guides inwards. L When the side registration home position switch (SRHPSW) turns off, the side registration motor (SRM) turns off. M 500 ms after the side registration home position switch (SRHPSW) turns off, the side registration motor (SRM) reverses for 5 pulses, and the side registration guide stops at its home position.
1-3-59
2AD (11) SRDF (11-1) Original feed section The original feed section consists of the parts shown in Figure 1-3-48. An original placed on the original table is conveyed to the original switchback section or the original conveying section.
# @ 3 7 $ 2 5 1
8 0
9
Figure 1-3-48 1 2 3 4 5 6 7 Original table DF forwarding pulleys DF original feed pulley DF separation pulley DF original feed upper guide DF original feed lower guide Original stopper Original feed section 8 9 0 ! @ # $ DF registration pulley DF registration roller DF registration guide Original set switch (OSSW) Original feed switch (OFSW) Original feed clutch (OFCL) Original feed solenoid (OFSOL)
1-3-60
2AD
OFSOL OFCL
OFSW
OSSW OFM
CN5-B12 CN5-B13
DFDPCB
Figure 1-3-49
CN5-B1 CN5-B6
CN6-B5
CN5-A5
CN6-B2
1-3-61
OFSOL A
200 ms
OFSOL R OFCL Fwd. rotation OFM Off Rev. rotation OFSW OSBSW OCM DFTSW
288 P*2 + 30 ms
556 P*1 20 ms
A The OFSOL A signal turns on for 200 ms and then the original feed solenoid (OFSOL) turns on, lowering the DF forwarding pulleys and releasing the original stopper to convey the original forward. The original feed clutch (OFCL) simultaneously turns on, rotating the DF original feed pulley to start primary original feed. The original feed motor (OFM) rotates forward during this operation. B 556 OFM pulses after the leading edge of the original turns the original feed switch (OFSW) on, the original feed clutch (OFCL) and original feed motor (OFM) turn off. 20 ms later, the rotation of the motor switches to the reverse direction and secondary original feed is performed by rotation of the DF registration roller. C 288 OFM pulses plus 30 ms after the leading edge of the original turns the DF timing switch (DFTSW) on, the original feed motor (OFM) turns off. D After ejection of the original, as the original conveying motor (OCM) turns off, the OFSOL R signal turns on for 200 ms and the original feed solenoid (OFSOL) turns off.
1-3-62
2AD (11-2) Original switchback section The original switchback section consists of the parts shown in Figure 1-3-50. The original from the original feed section or original conveying section is reversed and conveyed to the original conveying section.
2 7
3 5
4 6
Figure 1-3-50 Original switchback section 1 2 3 4 Switchback pulley Switchback roller Switchback feedshift guide Left switchback guide 5 6 7 8 Switchback guide Original switchback switch (OSBSW) Switchback feedshift solenoid (SBFSSOL) Switchback pressure solenoid (SBPSOL)
1-3-63
2AD
1-3-64
2AD Operation of original switchback In the double-sided original mode, the switchback feedshift solenoid (SBFSSOL) turns on, changing the position of the switchback feedshift guide. This switches the path of the original to the original switchback section to where the original is fed. The switchback feedshift solenoid (SBFSSOL) then turns off, allowing the switchback feedshift guide to return to the original position by which the path of the original is switched back to the original conveying section. The now reversed original is carried to the original conveying section and the switchback pressure solenoid (SBPSOL) turns off, releasing the switchback pulley to prevent an original jam in the original switchback section.
Switchback pulley
Figure 1-3-52
1-3-65
2AD (11-3) Original conveying section The original conveying section consists of the parts shown in Figure 1-3-53. Synchronized with the copier scanning operation, the original is conveyed across the slit glass and ejected when scanning is complete. In the double-sided original mode, the eject feedshift solenoid (EFSSOL) turns on, moving the eject feedshift guide to switch the path of the original. When the scanning of the first face (reverse face) of the original is complete, the original is conveyed to the original switchback section again.
% 1 0 7
2 $ 3 5 4 9 #
Figure 1-3-53 1 2 3 4 5 6 7 8
6 @ 8
Original conveying section 9 0 ! @ # $ % Original conveying guide Eject feedshift guide Upper eject guide Lower eject guide Slit glass (copier) DF timing switch (DFTSW) Eject feedshift solenoid (EFSSOL)
Upper original conveying pulley Upper original conveying roller Lower original conveying roller Front scanning pulley Middle original conveying roller Middle original conveying pulley Eject pulley Eject roller
1-3-66
2AD
OCM
EFSSOL DFTSW
CN5-A8 CN5-A13
CN6-A14
DFDPCB
CN5-A7
1-3-67
Fwd. rotation Off OFM Rev. rotation OFSW SBFSSOL SBPSOL OSBSW OCM EFSSOL DFTSW
Scanning speed
F G
*1 Burst of OFM pulses *2 Burst of OCM pulses
Timing chart 1-3-11 Reversing the first face of the original A During primary original feed, when the original feed switch (OFSW) turns on, the switchback feedshift solenoid (SBFSSOL) also turns on, changing the position of the switchback feedshift guide. This switches the path of the original to the original switchback section. B 556 OFM pulses plus 20 ms after the original feed switch (OFSW) turns on, the rotation of the original feed motor (OFM) switches to the reverse direction and the original is conveyed to the switchback section by the rotation of the switchback roller. The switchback pressure solenoid (SBPSOL) simultaneously turns on to operate the switchback pulley. C When the trailing edge of the original turns the original switchback switch (OSBSW) off, the switchback feedshift solenoid (SBFSSOL) turns off, the switchback feedshift guide returns to the original position. D 115 OFM pulses after the original switchback switch (OSBSW) turns off, the original feed motor (OFM) turns off. 100 ms later, the original feed motor (OFM) rotates forward, switching the rotational direction of the switchback roller. The original in the original switchback section is then reversed and conveyed to the original conveying section. E Simultaneously as the original feed motor (OFM) starts rotating forward, the original conveying motor (OCM) turns on to convey the original onto the slit glass. The eject feedshift solenoid (EFSSOL) simultaneously turns on, changing the position of the eject feedshift guide. This switches the path of the original to the original switchback section. F When the original is conveyed onto the slit glass, the DF timing switch (DFTSW) turns on. 288 OCM pulses later, the switchback pressure solenoid (SBPSOL). G 30 ms after the switchback pressure solenoid (SBPSOL) turns off, the original feed motor (OFM) turns off.
1-3-68
2AD
Scanning request signal : On Fwd. rotation Off OFM Rev. rotation OFSW SBFSSOL SBPSOL OSBSW OCM EFSSOL DFTSW Scanning speed
327 P*1 100 ms 115 P*1 564 P*1 30 ms 288 P*2 100 ms 30 ms 2337 P*2 + 30 ms
Scanning speed
B C D E
F G H I
Timing chart 1-3-12 Reversing of the second face of the original and ejection A 564 OFM pulses after the scanning of the first face (reverse face) of the original completes and the DF timing switch (DFTSW) turns off, the switchback pressure solenoid (SBPSOL) turns on, operationg the switchback pulley. B When the trailing edge of the original turns the original switchback switch (OSBSW) off, the eject feedshift solenoid (EFSSOL) turns off and the eject feedshift guide returns to the original position, switching the path of the original to the eject section. Simultaneously, the switchback feedshift solenoid (SBFSSOL) turns off and the switchback feedshift guide returns to the original position. C 30 ms after the original switchback switch (OSBSW) turns off, the original conveying motor (OCM) turns off. D 115 OFM pulses after the original switchback switch (OSBSW) turns off, the original feed motor (OFM) turns off. E 100 ms after the original feed motor (OFM) turns off, the motor starts rotating forward, switching the rotational direction of the switchback roller. The original in the original switchback section is then reversed and conveyed to the original conveying section. F 327 OFM pulses plus 100 ms after the original feed motor (OFM) turns off, the motor starts rotating forward again and the original conveying motor (OCM) turns on simultaneously, conveying the original onto the slit glass. G 288 OFM pulses after the original is conveyed onto the slit glass and the DF timing switch (DFTSW) turns on, the switchback pressure solenoid (SBPSOL) turns off. H 30 ms after the switchback pressure solenoid (SBPSOL) turns off, the original feed motor (OFM) turns off. I When the scanning request signal turns on, scanning of the second face (front face) of the original starts. J 2337 OCM pulses plus 30 ms after scanning of the second face (front face) of the original completes and the DF timing switch (DFTSW) turns off, the original conveying motor (OCM) turns off, completing the ejection of the original.
1-3-69
2AD (12) Large paper deck The large paper deck consists mainly of the right and left cassettes and separation section. The right cassette primary paper feed section sends paper from the lift to the upper and lower deck separation rollers. When the right cassette becomes empty, the left cassette primary paper feed section conveys paper onto the lift of the right cassette. The upper and lower deck separation rollers in the separation section convey paper received from the right cassette primary paper feed section into the copier, preventing multiple sheets from being fed at one time.
Figure 1-3-55 Mechanical construction (1) 1 2 3 4 5 6 7 Deck paper feed roller 1 Deck paper conveying roller Deck paper feed roller 2 Pickup arm Paper conveying base Lift Paper guide U 8 9 0 ! @ # $ Deck side cover Upper deck separation roller Lower deck separation roller Bracket Paper guide D Guide pulley Air damper
1-3-70
2AD
6 8 4 0
! 3
5 7 $ 9 1
% ^
( ) * # @ &
Figure 1-3-56 Mechanical construction (2) Paper path sensor 1 (PPSENS1) Paper path sensor 2 (PPSENS2) Paper path sensor 3 (PPSENS3) Paper empty sensor (PESENS) Deck level switch 1 (DLSW1, front) Deck level switch 2 (DLSW2, front) Upper limit switch 1 (UPSW1, rear) Upper limit switch 2 (UPSW2, rear) Paper feed clutch 1 (PFCL1) Paper feed clutch 2 (PFCL2) Paper conveying clutch (CCL) Paper deck motor pulse sensor 1 (PDMSENS1) # Paper deck motor pulse sensor 2 (PDMSENS2) 1 2 3 4 5 6 7 8 9 0 ! @ $ Deck open/closed safety switch (DOSSW) % Side cover switch (SCSW) ^ Deck paper conveying motor (CM) & Paper deck motor 1 (PDM1) * Paper deck motor 2 (PDM2) ( Paper level detection sensor 1 (PLDSENS1) ) Paper level detection sensor 2 (PLDSENS2) *Dehumidifier heater 1 (DH1) *Dehumidifier heater 2 (DH2) * Service part.
1-3-71
2AD (12-1) Right cassette primary paper feed As paper feed clutch 1 (PFCL1) turns on, the drive is transmitted to deck paper feed roller 1 and the upper and lower deck separation rollers, starting primary paper feed from the right cassette. The upper and lower deck separation rollers ensure that the paper is fed one sheet at a time and that it is fed into the copier correctly. To prevent multiple sheets from being fed, there is a torque limiter on the lower deck separation roller.
Paper feed signal from the copier 100 ms 64 P (70 ms) PFSW4 (copier)
B C
Timing chart 1-3-13 Right cassette primary paper feed A The paper feed signal from the copier turns paper feed clutch 1 (PFCL1) on, starting primary paper feed. B 64 pulses after paper feed switch 4 (PFSW4) on the copier has been turned on by the leading edge of the paper, paper feed clutch 1 (PFCL1) turns off. C 70 ms after paper feed switch 4 (PFSW4) on the copier has turned on, copier feed clutch 3 (FCL3) turns on to feed the paper to complete primary paper feed.
1-3-72
2AD
FCL3 Feed pulley Paper path Feed roller 4 Upper deck separation roller PFCL1 Deck paper feed roller 1 Copier
PFSW4
1-3-73
2AD When the right cassette is empty, its lift serves as a guide for the paper being conveyed from the left cassette lift.
PFSW4 (copier)
PFCL1
PFCL1
CN5-6
CN1-4
PFCL1
CN4-4
I/FPCB
PDMPCB
Figure 1-3-58 Right cassette primary paper feed section block diagram
1-3-74
2AD (12-2) Left cassette primary paper feed As the last sheet in the right cassette is fed, paper feed clutch 2 (PFCL2) and the paper conveying clutch (CCL) turn on for primary feed from the left cassette. Deck paper feed roller 2 and the deck paper conveying roller start to rotate to convey paper from the left cassette onto the right cassette lift.
B C
Timing chart 1-3-14 Left cassette primary paper feed A When copier paper feed switch 4 (PFSW4) is turned on by the last paper from the right cassette, paper feed clutch 2 (PFCL2) turns on to start primary paper feed. B The paper conveying clutch (CCL) turns on as soon as the leading edge of the paper from the left cassette turns paper path sensor 3 (PPSENS3) on. C Paper feed clutch 2 (PFCL2) turns off as soon as the leading edge of the paper from the left cassette turns paper path sensor 2 (PPSENS2) on, completing primary paper feed. D 43 pluses after the leading edge of the paper from the left cassette turns paper path sensor 1 (PPSENS1) on, the paper conveying clutch (CCL) turns off and the paper stops in the right cassette.
1-3-75
2AD
PPSENS1
PFSW4 (copier)
PFCL2
PFSW4 (copier) PPSENS2 PPSENS3 PFCL2 CCL PPSENS1 CN4-8 CN4-2 CN5-4 CN5-2 CN7-2 PPSENS2 CN2-6 PPSENS3 CN2-11 PFCL2 CN1-5 CCL CN1-6 PPSENS1 CN1-9 I/FPCB CN9-5 CN1-6 CN1-11 CN4-5 CN4-6 CN4-9 PDMPCB
Figure 1-3-60 Left cassette primary paper feed section block diagram
1-3-76
2AD (12-3) Raising and lowering the lifts The following is a description of the right cassette lift operating mechanism. The left cassette lift operates in the same manner. Paper deck motor 1 (PDM1) drives the right lift belt assembly that winches the belt up and hence raises the lift until it is stopped by deck level switch 1 (DLSW1). When paper is loaded on the lift and the deck is closed, the lift is raised until deck level switch 1 (DLSW1) turns on. When desk level switch 1 (DLSW1) is turned off as the paper on the lift is used, paper deck motor 1 (PDM1) starts to raise the lift until the switch turns on.
Deck level switch 1 Lift
Air damper
Figure 1-3-61 Raising and lowering the lift When the deck is opened for removing a jammed paper or other purposes, the winch shaft is released from its holder on paper deck motor 1 (PDM1), allowing the lift to descend under its own weight. The air damper buffers the impact of the descending lift.
1-3-77
2AD
DLSW2
DLSW1
PDM2
PDM1 DLSW1 DLSW2 CN3-3 CN3-9 DLSW1 CN2-7 DLSW2 CN2-9 CN1-7 CN1-9 PDM1 CN7-1 PDM2 CN7-4 PDMPCB
I/FPCB
1-3-78
2AD (12-4) Detecting the paper level The lift rises as paper in the deck is used. When the remaining number of sheets in either right or left cassette reduces to around 100 to 250 sheets, the projection on the lift belt assembly pushes against the sensor lever which turns the relevant paper level detection sensor 1 or 2 (PLDSENS1/2) on. When both paper level detection sensors 1 and 2 (PLDSENS1, 2) have turned on, the message Low on paper. is shown on the copier touch panel. This message is not shown when only one of them is on. As more copies are made with the message on, paper path sensors 1, 2 and 3 (PPSENS1, 2, 3) or the paper empty sensor (PESENS) start to detect absence of paper, and the message on the copier touch panel changes to Place paper in deck.
Sensor lever Sensor lever
Lift belt assembly Lift belt assembly When paper level detection sensor 1 is off When paper level detection sensor 1 is on
PLDSENS2
PLDSENS1
1-3-79
II ELECTRICAL SECTION
II Electrical Section
2AD
1-1-11
2AD
15
14
Machine inside
Figure 2-1-1 Copier (PCBs) 1. Main PCB (MPCB) ....................................... Controls the other PCBs, electrical components and optional devices; modifies and modulates image signal. 2. Power source PCB (PSPCB) ....................... Generates 24 V DC, +12 V DC and 5 V DC; controls fixing heaters M and S. 3. Engine PCB (EPCB) .................................... Interfaces output and input signals to and from electrical components and optional devices. 4. High-voltage transformer PCB (HVTPCB) ... Main charging. Generates developing bias, and high voltages for transfer and separation. 5. Scanner motor PCB (SMPCB) .................... Controls the scanner motor. 6. Scanner control PCB (SCPCB) ................... Controls the scanning section, SRDF and image processing. 7. Inverter PCB (INPCB) .................................. Controls the exposure lamp. 8. CCD PCB (CCDPCB) .................................. Reads the image off originals. 9. Operation unit main PCB (OMPCB) ............ Controls the operation unit. 10. Operation unit right PCB (ORPCB) ............. Consists of operation keys and display LEDs.
2-1-1
2AD 11. Operation unit left PCB (OLPCB) ................ Consists of the operation keys, backlight and display LEDs. 12. LCD ............................................................. Displays copy modes and messages. 13. Touch panel ................................................. Consists of a touch-sensitive layer which detects presses of operation keys displayed on the LCD. 14. Humidity sensor PCB (HUMPCB) ............... Detects the absolute humidity. External humidity sensor (EHUMSENS) ... Detects the external humidity. External temperature thermistor (ETTH) ... Detects the external temperature. 15. Memory copy PCB 1 (MCPCB1) ................. Reads and outputs the image. 16. Memory copy PCB 2 (MCPCB2) ................. Reads and outputs the image.
2-1-2
2AD
2 1 3,6 4 5
Machine inside
Figure 2-1-2 Copier (switches and sensors in the scanning system) 1. Scanner home position switch (SHPSW) .... Detects the scanner in the home position. 2. Original detection switch (ODSW) ............... Operates the original size sensors. 3. Original size sensors 1 and 2 (OSD1, 2) ..... Detects the original size. 4. Original size sensors 3 and 4 (OSD3, 4) ..... Detects the original size. 5. Original size sensors 5 and 6 (OSD5, 6) ..... Detects the original size. 6.*Original size sensors 7 and 8 (OSD7, 8) ..... Detects the original size. * For metric specifications only.
2-1-3
2AD
7 10 19 18 17 13 9 8
11
14
5 12 2
15
6 16
Machine inside
Figure 2-1-3 Copier (switches in the paper feed and conveying system) 1. Upper paper switch (PSW-U) ...................... Detects the presence of paper in the upper drawer. 2. Lower paper switch (PSW-L) ....................... Detects the presence of paper in the lower drawer. 3. Upper paper length switch (PLSW-U) ......... Detects the length of paper in the upper drawer (inch specifications). Detects the presence of the upper drawer (metric specifications). 4. Lower paper length switch (PLSW-L) .......... Detects the length of paper in the lower drawer (inch specifications). Detects the presence of the lower drawer (metric specifications). 5.*Upper paper width switch (PWSW-U) ......... Detects the width of paper in the upper drawer. 6.*Lower paper width switch (PWSW-L) .......... Detects the width of paper in the lower drawer. 7. Bypass paper switch (BYPPSW) ................. Detects the presence of paper on the bypass table. * For inch specifications only.
2-1-4
2AD 8. Bypass paper length switch (BYPPLSW) .... Detects the length of paper on the bypass table. 9. Bypass paper width switch (BYPPWSW) .... Detects the width of paper on the bypass table. 10. Bypass table extended detection switch ...... Detects when the bypass table support (BYPEDSW) guide is extended to use long paper. 11. Upper lift limit switch (LICSW-U) ................. Detects the upper drawer lift reaching the upper limit. 12. Lower lift limit switch (LICSW-L) .................. Detects the lower drawer lift reaching the upper limit. 13. Paper feed switch 1 (PFSW1) ..................... Controls feed clutch 4. 14. Paper feed switch 2 (PFSW2) ..................... Controls feed clutch 1, 2 and 3, and the upper paper feed clutch. 15. Paper feed switch 3 (PFSW3) ..................... Controls the lower paper feed clutch. 16. Paper feed switch 4 (PFSW4) ..................... Controls feed clutch 3. 17. Feed switch (FSW) ...................................... Controls the secondary paper feed start timing. 18. Registration switch (RSW) ........................... Controls the secondary paper feed end timing. 19. Eject switch (ESW) ...................................... Detects paper jam in the fixing section.
2-1-5
2AD
7 6
3 2
Machine inside
Figure 2-1-4 Copier (switches and sensors) 1. Main switch (MSW) ...................................... Turns the AC power on and off. 2. Safety switch 1 (SSW1) ............................... Breaks the safety circuit when the front cover is opened; resets paper jam detection. 3. Safety switch 2 (SSW2) ............................... Breaks the safety circuit when the left cover is opened; resets paper jam detection. 4. Safety switch 3 (SSW3) ............................... Breaks the safety circuit when the right cover is opened; resets paper jam detection. 5.*Heater switch (HSW) ................................... Turns the optical and drawer heaters on and off. 6. Toner sensor (TNS) ..................................... Detects the toner density in the developing section. 7. Toner level sensor (TLDS) .......................... Detects the toner level in the toner hopper. 8. Toner hopper lockup sensor (TLS) .............. Detects the amount of recycled toner in the toner hopper. 9. Fixing unit thermistor (FTH) ......................... Detects the heat roller temperature. * Service part.
2-1-6
2AD
1 12,13 2 7 8 10 9 11 4 3
Machine inside
Figure 2-1-5 Copier (motors) 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. Scanner motor (SM) .................................... Drives the scanner. Drive motor (DM) ......................................... Drives the image formation section. Paper feed motor (PFM) .............................. Drives the paper feed section. Paper conveying motor (PCM) .................... Conveys paper. Upper lift motor (CLM-U) ............................. Drives the upper drawer lift. Lower lift motor (CLM-L) .............................. Drives the lower drawer lift. Toner feed motor (TFM) .............................. Replenishes toner. Toner recycle motor (TRM) ......................... Replenishes recycled toner. Charger cleaning motor (CCM) ................... Cleans the transfer and separation charger wires. Image formation unit fan motor (IFFM) ........ Collects scattered toner. Paper conveying section fan motor ............. Assists paper advance along the paper (PCFM) conveying path and exhausts heat. Cooling fan motor 1 (CFM1) ........................ Cools the machine interior. Cooling fan motor 2 (CFM2) ........................ Cools the machine interior.
2-1-7
2AD
11 10 9 8 6 7 3
4 1
5 2
Machine inside
Figure 2-1-6 Copier (clutches and solenoids) 1. Upper paper feed clutch (PFCL-U) .............. Primary paper feed from the upper drawer. 2. Lower paper feed clutch (PFCL-L) .............. Primary paper feed from the lower drawer. 3. Feed clutch 1 (FCL1) ................................... Controls the drive of feed roller 1. 4. Feed clutch 2 (FCL2) ................................... Controls the drive of feed roller 2. 5. Feed clutch 3 (FCL3) ................................... Controls the drive of feed rollers 3 and 4. 6. Feed clutch 4 (FCL4) ................................... Controls the drive of the lower feed roller at high speed. 7. Feed clutch 5 (FCL5) ................................... Controls the drive of the lower feed roller at low speed. 8. Eject speed switching clutch (ESCL) ........... Switches the paper ejection speed. 9. Registration clutch (RCL) ............................ Secondary paper feed. 10. Bypass paper feed clutch (BYPPFCL) ........ Primary paper feed from the bypass table. 11. Bypass solenoid (BYPSOL) ......................... Operates the bypass forwarding pulley.
2-1-8
2AD
2 8 1
11 10 4 3 9 12 5
7 6
Machine inside
Figure 2-1-7 Copier (feedshift and duplex sections) 1. Feedshift switch (FSSW) ............................. Detects a paper jam in the feedshift section. 2. Switchback eject switch (SBESW) .............. Detects a paper jam in the switchback eject section. 3. Stock switch (STKSW) ................................ Detects the presence of paper in the duplex unit. 4. Duplex registration switch (DUPRSW) ........ Detects a paper jam in the duplex section. 5. Duplex paper conveying switch ................... Detects a paper jam in the duplex (DUPPCSW) paper conveying section. 6. Duplex eject switch (DUPESW) ................... Detects a paper jam in the duplex eject section. 7. Side registration home position switch ........ Detects the side registration guides in (SRHPSW) the home positions. 8. Feedshift solenoid (FSSOL) ........................ Operates the feedshift guide. 9. Duplex forward solenoid (DUPFWDSOL) .... Operates the duplex forwarding pulley. 10. Switchback feedshift solenoid ..................... Operates the switchback feedshift (SBFSSOL) guide. 11. Duplex paper tapping solenoid .................... Operates the paper tapping guide. (DUPPTSOL) 12. Side registration motor (SRM) ..................... Operates the side registration guides.
2-1-9
2AD
9 11 8 5,6 4 3 2
7 10
Machine inside
Figure 2-1-8 Copier (other electrical components) 1. Exposure lamp (EL) ..................................... Exposes originals. 2. Cleaning lamp (CL) ...................................... Removes residual charge from the drum surface. 3. Fixing heater M (H1) .................................... Heats the heat roller. 4. Fixing heater S (H2) .................................... Heats the heat roller. 5. Fixing unit thermostat 1 (TH1) ..................... Prevents overheating in the fixing section. 6. Fixing unit thermostat 2 (TH2) ..................... Prevents overheating in the fixing section. 7. Relay (PRY) ................................................. Turns the AC power and 24 V DC power supplies to the fixing section on and off. 8. Laser scanner unit (LSU) Polygon motor (PM) .................................. Drives the polygon mirror. Laser diode (LD) ........................................ Generates the laser beam. 9.*Optical heater (OPH) ................................... Dehumidifies the optical section. 10.*Drawer heater (CH) ..................................... Dehumidifies the drawer section. 11. Total counter (TC) ....................................... Displays the total number of copies produced. * Service part.
2-1-10
2 1
Machine inside
Figure 2-1-9 SRDF (PCBs) 1. DF driver PCB (DFDPCB) ........................... Controls electrical components of SRDF. 2. Original set LED PCB (OSLEDPCB) ........... Indicates presence of originals on the SRDF or an original jam.
2-1-11
2AD-1 2AD
2 4 5 6 3 8
Machine inside
Figure 2-1-10 SRDF (switches and sensors) 1. DF safety switch 1 (DFSSW1) ..................... Breaks the safety circuit when the SRDF is opened; resets original jam detection. 2. DF safety switch 2 (DFSSW2) ..................... Breaks the safety circuit when the DF original reversing cover is opened; resets original jam detection. 3. Original set switch (OSSW) ......................... Detects the presence of an original. 4. Original feed switch (OFSW) ....................... Detects primary original feed end timing. 5. Original switchback switch (OSBSW) .......... Detects an original jam in the original switchback section. 6. DF timing switch (DFTSW) .......................... Detects the original scanning timing. 7. Original size length switch (OSLSW) ........... Detects the length of the original. 8. Original size width switch (OSWSW) ........... Detects the width of the original.
2-1-12
2AD
1 2
Machine inside
Figure 2-1-11 SRDF (motors) 1. Original feed motor (OFM) ........................... Drives the original feed and switchback sections. 2. Original conveying motor (OCM) ................. Drives the original conveying section.
2-1-13
2AD
2 4
5 3
Machine inside
Figure 2-1-12 SRDF (clutches and solenoids) 1. Original feed solenoid (OFSOL) .................. Moves the DF forwarding pulleys vertically. 2. Switchback feedshift solenoid ..................... Moves the switchback feedshift guide. (SBFSSOL) 3. Eject feedshift solenoid (EFSSOL) .............. Moves the eject feedshift guide. 4. Switchback pressure solenoid ..................... Moves the switchback pulley. (SBPSOL) 5. Original feed clutch (OFCL) ......................... Controls the drive of the DF original feed pulley.
2-1-14
Machine inside
Figure 2-1-13 Large paper deck (PCBs) 1. Deck main PCB (PDMPCB) ........... Controls other PCBs and electrical components. 2. Interface PCB (I/FPCB) .................. Interfaces between the deck main PCB and other electrical components.
2-1-15
2AD
8 6 4 14
7 3 2 5 13
1 10 9
12
11
Machine inside
Figure 2-1-14 Large paper deck (switches and sensors) 1. Paper path sensor 1 (PPSENS1) .... Detect paper jams and the absence of paper on the lifts. 2. Paper path sensor 2 (PPSENS2) .... Detect paper jams and the absence of paper on the lifts. 3. Paper path sensor 3 (PPSENS3) .... Detect paper jams and the absence of paper on the lifts. 4. Paper empty sensor (PESENS) ...... Detects the absence of paper in the left cassette. 5. Deck level switch 1 (DLSW1) .......... Detects the right cassette lift in the home position. 6. Deck level switch 2 (DLSW2) .......... Detects the left cassette lift in the home position. 7. Upper limit switch 1 (UPSW1) ......... Detects the right cassette lift being raised past the limit. 8. Upper limit switch 2 (UPSW2) ......... Detects the left cassette lift being raised past the limit. 9. Side cover switch (SCSW) .............. Detects if the deck side cover is opened or closed. 10. Deck open/closed safety switch ...... Detects if the deck is open or closed. (DOSSW) 11. Paper deck motor pulse sensor 1 .... Detects abnormal paper deck motor 1 rotation. (PDMSENS1) 12. Paper deck motor pulse sensor 2 .... Detects abnormal paper deck motor 2 rotation. (PDMSENS2) 13. Paper level detection sensor 1 ........ Detects the paper level in the right cassette. (PLDSENS1) 14. Paper level detection sensor 2 ........ Detects the paper level in the left cassette. (PLDSENS2)
2-1-16
2AD
4 1
8 2 7
Machine inside
Figure 2-1-15 Large paper deck (other electrical components) 1. Deck paper conveying motor .......... Drives the large paper deck. (CM) 2. Paper deck motor 1 (PDM1) ........... Raises the right cassette lift. 3. Paper deck motor 2 (PDM2) ........... Raises the left cassette lift. 4. Paper feed clutch 1 (PFCL1) .......... Regulates drive transmission to deck paper feed roller 1, and the upper and lower deck separation rollers. 5. Paper feed clutch 2 (PFCL2) .......... Regulates drive transmission to deck paper feed roller 2. 6. Paper conveying clutch (CCL) ........ Regulates drive transmission to the deck paper conveying roller. 7.*Dehumidifier heater 1 (DH1) ........... Dehumidifies paper in the right cassette. 8.*Dehumidifier heater 2 (DH2) ........... Dehumidifies paper in the left cassette. * Service part.
2-1-17
2AD
1-1-13
2AD
3 6
7 2
1 4
Inch
3 6
7 2
1 4
Figure 2-2-1 Misfeed location indication 1 2 3 4 Paper feed section Paper conveying section Fixing and eject section Duplex section 5 Large paper deck 6 Finisher* 7 SRDF * Optional.
2-2-1
2AD
BYPPFCL RCL SBESW ESW FSSW DUPFWDSOL DUPRSW DUPPCSW DUPESW PFCL-U PFSW2 RSW FSW PFSW1
PFCL-L
PFSW3
PFSW4
2-2-2
2AD 1. Jam at power-on (jam code 00) One or more of the switches in the paper conveying system is on when the main switch is turned on. 2. Paper feed section No paper feed from copier upper drawer (jam code 10) Paper feed switch 2 (PFSW2) does not turn on within 586 ms of the upper paper feed clutch (PFCL-U) turning on; the clutch is then held off for 1 s and turned back on, but the switch again fails to turn on within 586 ms of the retry.
PFCL-U 1s Off On 586 ms 586 ms Off On
PFSW2
No paper feed from copier lower drawer (jam code 11) Paper feed switch 3 (PFSW3) does not turn on within 586 ms of the lower paper feed clutch (PFCL-L) turning on; the clutch is then held off for 1 s and turned back on, but the switch again fails to turn on within 586 ms of the retry.
1s Off On 586 ms 586 ms Off On
PFCL-L
PFSW3
No paper feed from bypass (jam code 14) The feed switch (FSW) does not turn on within 1120 ms of the bypass paper feed clutch (BYPPFCL) turning on; the clutch is then held off for 1 s and turned back on, but the switch again fails to turn on within 1120 ms of the retry.
BYPPFCL 1s Off On 1120 ms 1120 ms Off On
FSW
2-2-3
2AD Jam in copier vertical paper conveying section (jam code 18) The feed switch (FSW) does not turn on within 780 ms of paper feed switch 1 (PFSW1) turning on.
Off PFSW1 On 780 ms Off On
FSW
Paper feed switch 1 (PFSW1) does not turn on within 733 ms of paper feed switch 2 (PFSW2) turning on.
Off PFSW2 On 733 ms Off On
PFSW1
Paper feed switch 2 (PFSW2) does not turn on within 814 ms of paper feed switch 3 (PFSW3) turning on.
Off PFSW3 On 814 ms Off On
PFSW2
Jam in converging section (jam code 20) The registration switch (RSW) does not turn on within 444 ms of the feed switch (FSW) turning on.
Off FSW On 444 ms Off On
RSW
2-2-4
2AD Multiple sheets in paper feed section (jam code 21) Paper feed switch 2 or 3 (PFSW2 or 3) does not turn off within 1470 ms of turning on.
PFSW2 PFSW3
1470 ms
Off On
Timing chart 2-2-8 Multiple sheets in copier vertical conveying section (jam code 22) Paper feed switch 1 (PFSW1) does not turn off within 733 ms of paper feed switch 2 (PFSW2) turning off.
Off PFSW2 On 733 ms Off On
PFSW1
Paper feed switch 2 (PFSW2) does not turn off within 814 ms of paper feed switch 3 (PFSW3) turning off.
PFSW2
Paper feed switch 1 (PFSW1) does not turn off within 833 ms of duplex eject switch (DUPESW) turning off.
Off DUPESW On 833 ms Off On
PFSW1
2-2-5
2AD Multiple sheets before registration section (jam code 23) The feed switch (FSW) does not turn off within 1340 ms of paper feed switch 1 (PFSW1) turning off.
Off PFSW1 On 1340 ms Off On
FSW
The feed switch (FSW) does not turn off within 2528 ms of turning on during bypass paper feed.
FSW
2528 ms
Off On
3. Paper conveying section Jam in registration/transfer section (jam code 30) The registration switch (RSW) does not turn off within 764 ms of the feed switch (FSW) turning off.
RSW
2-2-6
2AD 4. Fixing section Jam in fixing section (jam code 40) The eject switch (ESW) does not turn on within 2552 ms of the registration clutch (RCL) turning on.
Off RCL On 2552 ms Off On
ESW
5. Eject section Jam in eject section (jam code 50) The eject switch (ESW) does not turn off within 2528 ms of turning on.
ESW
2528 ms
Off On
Jam in switchback eject section (jam code 51) The switchback eject switch (SBESW) does not turn off within 1470 ms of turning on.
SBESW
1470 ms
Off On
2-2-7
2AD 6. Feedshift section Jam in feedshift section (jam code 52) The feedshift switch (FSSW) does not turn on within 1400 ms of the eject switch (ESW) turning on.
Off ESW On FSSW 1400 ms Off On
Timing chart 2-2-18 The feedshift switch (FSSW) does not turn off within 1400 ms of the eject switch (ESW) turning off.
Off ESW On FSSW 1400 ms Off On
Timing chart 2-2-19 7. Duplex section Jam in duplex stock section (jam code 60) The switchback eject switch (SBESW) does not turn on within 856 ms of the duplex forward solenoid (DUPFWDSOL) turning on.
2-2-8
2AD The duplex registration switch (DUPRSW) does not turn on within 707 ms of the duplex forward solenoid (DUPFWDSOL) turning on.
Off DUPFWDSOL On DUPRSW 707 ms Off On
Timing chart 2-2-21 Duplex paper conveying section (jam code 61) The duplex paper conveying switch (DUPPCSW) does not turn on within 860 ms of the duplex registration switch (DUPRSW) turning on.
Off DUPRSW On DUPPCSW 860 ms Off On
Timing chart 2-2-22 The duplex eject switch (DUPESW) does not turn on within 860 ms of the duplex paper conveying switch (DUPPCSW) turning on.
Off DUPPCSW On DUPESW 860 ms Off On
Timing chart 2-2-23 Paper feed switch 1 (PFSW1) does not turn on within 833 ms of the duplex eject switch (DUPESW) turning on.
Off DUPESW On PFSW1 833 ms Off On
2-2-9
2AD Duplex registration switch (DUPRSW) does not turn off within 1470 ms of turning on.
Off On
DUPRSW
1470 ms
Timing chart 2-2-25 Duplex paper conveying switch (DUPPCSW) does not turn off within 860 ms of the duplex registration switch (DUPRSW) turning off.
Off DUPRSW On DUPPCSW 860 ms Off On
Timing chart 2-2-26 The duplex eject switch (DUPESW) does not turn off within 860 ms of the duplex paper conveying switch (DUPPCSW) turning off.
Off DUPPCSW On DUPESW 860 ms Off On
2-2-10
PFSW4
PFCL2
PPSENS3
PPSENS2
PPSENS1 PFCL1
Figure 2-2-3 Large paper deck No paper feed from large paper deck (jam code 12) Paper feed switch 4 (PFSW4) does not turn on within 672 ms of paper feed clutch 1 (PFCL1) turning on; the clutch is then held off for 1 s and turned back on, but the switch again fails to turn on within 672 ms of the retry.
Off On 672 ms 672 ms Off On
PFCL1
1s
PFSW4
Timing chart 2-2-28 Multiple sheets in paper feed section (jam code 21) Paper feed switch 4 (PFSW4) does not turn off within 1470 ms of turning on.
PFSW4
1470 ms
Off On
2-2-11
2AD Paper failing to reach PPS2 in large paper deck horizontal paper path (jam code 15) Paper path sensor 3 (PPSENS3) does not turn on within 260 ms of paper feed clutch 2 (PFCL2) turning on.
Off PFCL2 On 260 ms Off On
PPSENS3
Timing chart 2-2-30 Paper failing to reach PPS1 in large paper deck horizontal paper path (jam code 16) Paper path sensor 2 (PPSENS2) does not turn on within 150 ms of paper path sensor 3 (PPSENS3) turning on.
Off PPSENS3 On 150 ms Off On
PPSENS2
Timing chart 2-2-31 Paper failing to reach PPS0 in large paper deck horizontal paper path (jam code 17) Paper path sensor 1 (PPSENS1) does not turn on within 405 ms of paper path sensor 2 (PPSENS2) turning on.
Off PPSENS2 On 405 ms Off On
PPSENS1
2-2-12
2AD (3) Finisher (see the finisher service manual) Initial clogging jam (jam code 00) Jam in paper entry section (jam code 81) Jam in eject section of non-sort tray (jam code 82) Jam in paper conveying section of internal tray (jam code 83) Jam in eject section of sort tray (jam code 84)
2-2-13
2AD
OCM
DFTSW
Figure 2-2-4
2-2-14
2AD
Timing chart 2-2-33 An original jam in the original feed/conveying section (jam code 71) During the secondary original feed in the single-sided original mode, the DF timing switch (DFTSW) does not turn on within 3425 original feed motor (OFM) pulses from the start of reverse rotation of the original feed motor (OFM). Alternatively, during continuous original feed in the single-sided original mode, the DF timing switch (DFTSW) does not turn on for the second time under the above conditions.
Timing chart 2-2-34 During the secondary original feed in the single-sided original mode, the original feed switch (OFSW) has not turned off before the DF timing switch (DFTSW) turns off.
2-2-15
2AD During original switchback operation in the double-sided original mode, the original feed switch (OFSW) remains on when the original switchback switch (OSBSW) turns off.
Off OSBSW On Off OFSW On
Timing chart 2-2-35 During the secondary original feed in the single-sided or double-sided original mode, the DF timing switch (DFTSW) does not turn on within 10200 original conveying motor (OCM) pulses from the DF timing switch (DFTSW) turning on.
Off On * Burst of OCM pulses
DFTSW
10200 P*
Timing chart 2-2-36 In the single-sided or double-sided original mode, the DF timing switch (DFTSW) turns off within 2016 original conveying motor (OCM) pulses from the DF timing switch (DFTSW) turning on.
Off On * Burst of OCM pulses
DFTSW
2016 P*
Timing chart 2-2-37 While scanning the first face (reverse face) of an original in the double-sided original mode, the original switchback switch (OSBSW) does not turn on within 3591 original conveying motor (OCM) pulses from the DF timing switch (DFTSW) turning on.
Off DFTSW On OSBSW 3591 P* Off On * Burst of OCM pulses
2-2-16
2AD An original jam in the original switchback section (jam code 72) During the switchback operation of an original in the double-sided original mode, the original switchback switch (OSBSW) does not turn on within 2520 original feed motor (OFM) pulses from the start of reverse rotation of the original feed motor (OFM).
Off OFM On (Rev.) OSBSW 2520 P* Off On * Burst of OFM pulses
Timing chart 2-2-39 During switchback operation of an original in the double-sided original mode, the original switchback switch (OSBSW) does not turn off within 5100 original feed motor (OFM) pulses from the original switchback switch (OSBSW) turning on.
Off On * Burst of OFM pulses
OSBSW
5100 P*
Timing chart 2-2-40 During the secondary original feed in the double-sided original mode, the DF timing switch (DFTSW) does not turn on within 1528 original conveying motor (OCM) pulses from the original conveying motor (OCM) turning on.
Off OCM On DFTSW 1528 P* Off On * Burst of OCM pulses
2-2-17
2AD
1-1-15
2AD
PSPCB
Rectifier circuit L D001 Noise filter circuit L1* Noise filter circuit L001 L101 D107 D108 T1
~
N
Q101 Zero-cross circuit H2 H1 TR2 C TR3 D PT2 H2 REM H1 REM T1 D201 D203 24 V DC output circuit IC3 D202 A B C PC1 PC2 PC3 5.1 V DC output circuit IC5 (sub) L201 PT1 Power-factor improvement control circuit (IC1)
C101 + Q103
Q104
B SLEEP SIG
24 V DC Q201 GND 12 V DC output circuit IC6 Overvoltage/ overcurrent detection D circuits 5.1 V DC GND 5.1 V DC GND Z CROSS SIG 12 V DC GND
TH
2-3-1
2AD The power source PCB (PSPCB) is a switching regulator which converts an AC input to generate 24 V DC, 5.1 V DC and 12 V DC. It consists of the components shown in Figure 2-3-1; noise filter circuit, rectifier circuit, power factor improvement control circuit, switching control circuit, 24 V DC output circuit, 5.1 V DC output circuit, 12 V DC output circuit, fixing heater control circuit, cooling fan control circuit, overheat detection circuit, overvoltage detection circuit, overcurrent detection circuit. The noise filter circuits, consisting mainly of the noise filter circuit in the power source section and capacitors, attenuates external noise and prevents switching noise generated by the power source circuit and the heater control circuit from leaving the machine via the AC line. The rectifier circuit full-wave rectifies the AC input which has passed through the noise filter using the diode bridge D001. In the power factor improvement control circuit, a boosting converter, the controller IC1 turns FETs Q101 and Q102 on and off at high frequency so that the waveform of the input current becomes analogous with the waveform of the constantly-monitored input voltage. It then restores this by imitating the input voltage waveform to improve the wave form of the input current (which usually looks like pulses) into sine waves. Choke coil L101 and diodes D107 and D108 are part of the boosting converter. The switching control circuit turns the FETs Q103 and Q104 on and off via the PWM controller IC2 to apply the AC component from the DC voltage smoothed via the electrolytic capacitor C101 to the primary coil of the transformer T1. The 24 V DC output circuit smoothes the current induced on the secondary coil of the transformer T1 via diodes D201, D202 and D203, and outputs a more stable 24 V DC by the function of shunt regulator IC3. The output status of 24 V DC is fed back to the PWM control IC2 in the switching control circuit via the photocoupler PC1, and based on the feedback, the PWM control IC2 outputs stable 24 V DC constantly by controlling the switching duty pulse width for the FETs Q103 and Q 104. The 5.1 V DC output control circuits IC4 and IC5 receive 24 V DC from the 24 V DC output circuit and output stable 5.1 V DC by the function of the DC/DC converter control IC4 and IC5. The 12 V DC output circuit receive 24 V DC from the 24 V DC output circuit and outputs stable 12 V DC by the function of a power supply regulator. The cooling fan control circuit IC7 monitors the temperature of heating elements on the primary side, and activates the cooling fan if the temperature reaches the predetermined level for forced air-cooling of the heating elements. In the energy saving mode, FET Q201 conducts when it receives a sleep signal from the main PCB (MPCB), thus cutting off the output of 24 V DC. Since input to the 12 V DC control circuit IC6 is also cut off, output of 12 V DC also ceases. The 5.1 V DC output circuit IC4 also stops the control circuit IC5 and output of 5.1 V DC when it receives a sleep signal. As a result, all outputs except the sub-output from the 5.1 V DC output circuit IC5 are cut off, by which means energy consumption is lowered to the Energy Star accreditation level while in the stand-by mode. Abnormal rise of voltage for all DC outputs and overcurrent in all outputs except the 24 V DC and 12 V DC outputs are monitored by the overvoltage and overcurrent detection circuits, and if any abnormal rise is detected, alarm signals are fed back to the PWM control circuit IC2 on the primary side via photocoupler PC2, by which means power supply is shut down. Overload of the 24 V DC output is monitored by resistors R117 and R118 as the total sum of current on the primary side, and if any abnormal condition is detected, the operation of the PWM control circuit IC2 stops and the power supply is
2-3-2
2AD shut down. Overload of the 12 V DC output circuit is controlled by the overcurrent protection function of power source regulator IC7. When the abnormal output condition is removed, the 12 V DC output returns to the normal output condition. The fixing heater control circuit sends zero-crossing signal (Z CROSS SIG) via the photocoupler PC3 to the main PCB (MPCB). These signals are in turn converted into signals to control the on/off timing and phases, which are then input to the power source PCB (PSPCB) as the H1 REM and H2 REM signals. The phototriacs PT1 and PT2 are turned on by the H1 REM and H2 REM signals, and electricity flows through triacs TR2 and TR3 to turn the fixing heaters on.
2-3-3
2AD
EPCB
Communication interface
Switches, sensors
Motors
Driver IC
Clutches, solenoids
High-voltage transformer PCB *1: Optional. *2: Optional for 120 V specifications only.
Figure 2-3-2 Engine PCB block diagram The engine PCB (EPCB) transmits the status of each switch to the main PCB (MPCB) and transmits the control signals output from the main PCB (MPCB) through driver ICs to motors, clutches and solenoids. It also receives and transmits input and output signals to and from optional devices via a communication interface.
2-3-4
2AD
SRDF
Address bus
Data bus
Main CPU IC28 EPROM IC11 Backup RAM IC16 SRAM IC43 Engine CPU IC21 EPROM IC10 SRAM IC15
SELA
SELB
FIFO IC40
SELC
IC42
VIDEO DATA
LSU
ASIC1 IC33
ASIC2 IC19
IC9
2-3-5
2AD The main PCB (MPCB) consists of the main CPU IC28, the engine CPU IC21, communication microcomputers IC41 and IC7, SRAMs IC43 and IC15, batteryintegrated RAM for back-up IC16, EPROMs IC11 and IC10, a dual port RAM IC29, ASICs for input and output control IC33 and IC19, an ASIS for controlling image data output IC42. The main CPU IC28 controls the engine CPU IC21, and the flow of image data transmitted between memory copy PCB 1 (MCPCB1), memory copy PCB 2 (MCPCB2), the scanner control PCB (SCPCB) and the printer board. The engine CPU IC21 controls the operation of motors, clutches and solenoids, output of image data and communication with optional devices via the engine PCB (EPCB).
2-3-6
2AD
CPU U17
SRAM U4,11
EPROM U1
ASIC U16
CODEC U26
Address bus
Address bus
FF
2-3-7
2AD The following is a description of memory copy PCB 1 (MCPCB1). Memory copy PCB 2 (MCPCB2) is identical to memory copy PCB 1 (MCPCB1). Memory copy PCB 1 (MCPCB1) consists of CPU U17, ASIC U16, SRAMs U4 and U11, DRAMs U13, U14, U15, U18, U19 and U20, EPROM U1, and CODECs U25 and U26. The memory copy PCB mainly serves to read images from the scanner based on the control signals from the main PCB (MPCB), and output the images to the engine (the component where printing to paper and driving of mechanisms are executed). It also performs editing operations such as image rotation, image summary and image synthesizing. Since the original scanning speed of the scanner and the printing speed of the engine (the component where printing to paper and driving of mechanisms are executed) are different, and their operations not synchronized, memory copy PCB 1 (MCPCB1) also serves as a buffer to deal with the speed and timing differences between them.
2-3-8
2AD
SCPCB Analog differential communication receivers IC23, 24 Digital differential driver IC 25 S/H IC16 A/D converters IC14, 15
CCD PCB
ASIC1 IC17 Image data High speed SRAMs IC26, 27 Bus line
Main PCB
ASIC2 IC5
EPROM IC28
Switches, sensors
SM
INPCB
EL
Figure 2-3-5 Scanner control PCB block diagram The scanner control PCB (SCPCB) drives the CCD PCB (CCDPCB), processes image signals, controls the scanner motor (SM) and the exposure lamp (EL), processes input from the original size sensors (OSD1, 2, 3, 4, 5, 6, 7* and 8*) of the scanner unit, and controls the SRDF. The CPU IC22 communicates with the main PCB (MPCB) to control operations. * For inch specifications only.
2-3-9
2AD The driving of the CCD PCB (CCDPCB) and processing of images input from the CCD PCB (CCDPCB) are performed by CPU IC22 via ASIC1 IC17. The image data is converted from analog to digital and transmitted to ASIC2 IC5. ASIC2 IC5 processes the image in response to instructions from the CPU IC22 and transmits the image data to the main PCB (MPCB). ASIC1 IC17 and ASIC2 IC5 output PG data depending on instructions from the CPU IC22. The SRDF is controlled by signals from the ports of CPU IC22 and XIO IC21 to SRDF motors, clutches and solenoids in response to signals generated by sensors in the SRDF. The scanner motor (SM), the exposure lamp (EL) and the scanner home position switch (SHPSW) are also controlled through the ports of CPU IC22 and XIO IC21. To detect the size of an original, the original size sensors (OSD1, 2, 3, 4, 5, 6, 7* and 8*) are monitored under the control of original size detection microcomputer IC29 from the port of XIO IC21. * For inch specifications only.
2-3-10
2AD
SMPCB
Driver IC1
SM A SM A SM B SM B
SM
5 V DC
SHPSW
EL
Figure 2-3-6 Scanner motor PCB block diagram The scanner motor PCB (SMPCB) drives the scanner motor (SM), turns the exposure lamp (EL) on and off, and relays signals from the scanner home position switch (SHPSW) and the original detection switch (ODSW). The scanner motor (SM) is driven by turning the output for motor phase switchover on and off (SM A, SM A, SM B, SM B). It is activated by the driver IC1 processing the currently set reference signal (SM Vref), mode signals (SM M1 - M3, SM CWB), phase changeover clock (SM CLK), drive/stop signals (SM ENABLE) from the scanner control PCB. The exposure lamp (EL) is turned on when the signal (EL ON REM) from the scanner control PCB (SCPCB) is inverted by DT2 and the resulting lamp on/off signal (EL) goes low. Signals from the scanner home position switch (SHPSW) and the original detection switch (ODSW) are relayed to the scanner control PCB (SCPCB).
2-3-11
2AD-1 2AD
CCDPCB
11 clks
4 clks
IC3
Clock generation
CCD IC1
Odd
Even
2-3-12
2AD
DFDPCB 24 V DC 24 V DC OCM A OCM B OCM A OCM B 24 V DC Scanner control PCB Motor driver IC 24 V DC OFM A OFM B OFM A OFM B
Motor driver IC
OCM
OFM
Switches
Clutches, solenoids
Figure 2-3-8 DF driver PCB block diagram The DF driver PCB (DFDPCB) consists of a motor drive ICs and several other components. It mainly serves to drive the original feed motor (OFM) and the original conveying motor (OCM), under the control of signals received form the scanner control PCB (SCPCB). It also relays the 24 V DC power supply to the SRDF clutches and solenoids and the 5 V DC power supply to various switches and drives, and relays inputs and outputs of other signals.
2-3-13
2AD
2-3-9 Operation unit main PCB, operation unit right PCB, and operation unit left PCB
OMPCB CFL
Address bus Data bus
EPROM IC12
EPROM IC16
Reset circuit
Chip select
LCD
23 V DC
SRAM IC20
Figure 2-3-9 Operation unit main PCB, operation unit right PCB, and operation unit left PCB block diagram
2-3-14
2AD On the operation unit main PCB (OMPCB), the major component is the CPU IC19, which directly controls the operation of the machine in response to a control program located in EPROM IC12 and executed from SRAM IC9. EPROM IC16 contains font data for the LCD display and LCD controller IC11 controls the LCD panel display from instructions contained in SRAM IC20. The operation unit right PCB (ORPCB), consisting of key switches and LEDs, is controlled by scan signals and LED lighting signals from the operation unit main PCB (OMPCB). The operation unit left PCB (OLPCB) consists of key switches, LEDs and the CFL lighting drive circuit. Key switches and LEDs are controlled by scan signals and LED lighting signals from the operation unit main PCB (OMPCB), and the CFL lighting drive circuit. This circuit generates AC power for CFL lighting drive and is controlled by the turning on and off of CFL lighting signals by the operation unit main PCB (OMPCB).
2-3-15
KEY4 KEY5
KEY6 KEY7
D2
D3
R1
R2
R3 TR1
R4
R5 TR2
R6
TR3
LED10
LED11
LED12
LED13
LED14
LED15
R13
LED16 R15
LED1
LED2
LED3
LED4
LED5
LED6
LED7
LED8
LED9
R14
Figure 2-3-10 Operation unit left PCB block diagram Selection of key switches and the lighting of LEDs are determined by scan signals (SCAN L1 - L3) and LED signal selection signals (DIGLED L1 - L4). The key switch operated is identified by the scan signals (SCAN L1 - L3) and the return signals (DIGKEY L1 - L3). As an example, to light LED 1, the LED lighting selection signal (DIGLED L1) should be driven low in synchronization with a low level on the scan signal (SCAN L1). Transistor TR1 conducts and LED1 is lit. LEDs can be lit dynamically by repeating such operations. As an example, if KEY1 is pressed, the corresponding key switch is turned on feeding the low level of the scan signal back to the operation unit main PCB (OMPCB) via the return signal (DIGKEY L1). The operation unit main PCB (OMPCB) locates the position where the line outputting the scan signal and the line inputting the return signal cross, and thereby determines which key switch was operated.
2-3-16
N.C.
TB
KEY8 KEY9 DIGKEY R1 DIGKEY R2 DIGKEY R3 DIGKEY R4 CNB-1 CNB-2 CNB-3 CNB-4 KEY11 KEY10
KEY15
KEY19
KEY23
D5
D6
D7
SCAN R3 SCAN R4
R7
R8
BZ
TR4
BUZZER
CNB-13
LED17
LED18
LED19
Figure 2-3-11 Operation unit right PCB block diagram The operation unit right PCB (ORPCB) consists of key switches and LEDs. Depending on the scan signals (SCAN R1 - R4) and the LED lighting selection signals (DIGLED R1 - R4) received from the operation unit main PCB (OMPCB), the LED to be lit is selected, and the key switch pressed is identified by the scan signals (SCAN R1 - R4) and the return signals (DIGKEY R1 - R4). As an example, to light LED17, the LED lighting selection signal (DIGLED R1) should be driven low in synchronization with a low level on the scan signal (SCAN R1). Transistor TR4 conducts and LED17 is lit. LEDs can be lit dynamically by repeating such operations. As an example, if KEY8 is pressed, the corresponding key switch is turned on feeding the low level of the scan signal back to the operation unit main PCB (OMPCB) via the return signal (DIGKEY R1). The operation unit main PCB (OMPCB) locates the position where the line outputting the scan signal and the line inputting the return signal cross, and thereby determines which key switch was operated.
LED20
2-3-17
2AD
Main PCB
Engine DECK TXD PCB DECK RXD PFSW4 Deck paper conveying motor drive circuit
Communication circuit
Latch
ROM
CM
Reset circuit
Figure 2-3-12 Deck main PCB block diagram The deck main PCB (PDMPCB) consists of the CPU IC7, which serially communicates with the main PCB (MPCB) via the engine PCB (EPCB); the deck paper conveying motor drive circuit; the paper deck motor drive circuits; the clutch drive circuit; the reset circuit; and the LED drive circuit. It controls the entire large paper deck.
2-3-18
+24 V DC R25 1
+24 V D1 DC SIG
+5 V DC
58
8 IC6.4
2 R36
CN1-8
UPSW1
PDMPCB
Figure 2-3-13 Paper deck motor 1 drive circuit The following is a description of the paper deck motor 1 drive circuit. Paper deck motors 1 and 2 are identical. When pin 14 of the CPU IC7 goes low, transistor Q1 is turned on causing paper deck motor 1 (PDM1) to rotate. When transistor Q1 is turned off, paper deck motor 1 (PDM1) stops. A brake circuit ensures the prompt stopping of the motor. When transistor Q1 turns off, transistor Q3 turns on, supplying 24 V DC to CN7-1 thereby preventing paper deck motor 1 (PDM1) from rotating further under momentum. When the right cassette lift is raised past the limit, upper limit switch 1 (UPSW1) turns on, taking the level at pin 58 of the CPU IC7 low, which turns transistor Q1 and hence paper deck motor 1 (PDM1) off. This level change is also passed to pin 9 of a protective circuit consisting of IC8.3, forcing paper deck motor 1 (PDM1) off directly in case the CPU IC7 fails.
2-3-19
+24 V DC 9 16 COM1 COM2 CPU IC7 19 3 6 11 14 IN1 IN2 IN3 IN4 IC4 01 02 03 04 2 7 10 15
PDMPCB
When pin 19 of the CPU IC7 goes low, pin 2 of IC4 goes low, which turns the paper conveying clutch (CCL) on. The other clutches are controlled in the same manner.
2-3-20
2AD (3) Operating principle of reflective photosensors PPSENS1, PPSENS2, PPSENS3 and PESENS
5 CPU IC7
5 IC5.3
R43 R15
Q14
76
8 IC9.4
Off On
Figure 2-3-15 Reflective photosensor (PPSENS3) circuit The following is the operating principle of paper path sensor 3 (PPSENS3). Paper path sensors 1 and 2 (PPSENS1, PPSENS2) and the paper empty sensor (PESENS) operate in the same manner. Pulsating signal from pin 5 of the CPU IC7 turns Q14 on and off, causing the LED on the sensor PCB to flash. When the flashing LED light reflects on the paper, the phototransistor turns on and off. The on/off signal is then inverted by IC9.4 and the paper presence signal (pulse) is input at pin 76 of the CPU IC7. If there is no paper, the phototransistor remains off and 5 V DC is input at pin 76 of the CPU IC7.
2-3-21
+5 V DC
50 7
CPU IC7
TCK CT
RES
Figure 2-3-17 CPU reset operation timing chart (abridged) IC1 monitors the supply voltage and also determines if the CPU IC7 is operating correctly. If the supply voltage VCC drops below VSL (approx. 4.2 V DC), the reset signal (RES) is output to the CPU IC7 (A in the timing chart). IC1 monitors the clock signal (CK) from pin 50 of the CPU IC7 which goes low periodically. If the CPU IC7 fails, IC1 detects that the clock signal (CK) has stopped and sends a reset signal (RES) to the CPU IC7 (B in the timing chart). To reset the CPU IC7, pin 8 (RES) of IC1, which usually outputs 5 V DC, goes low and takes the level at pin 7 of the CPU IC7 low.
2-3-22
2AD
1-1-17
2AD-1
Figure 3-1-1 Installation dimensions a: 811 mm/3115/ 16" b: 1131 mm/441/2" c: 627 mm/2411/16" d: 1279 mm/503/8" e: 748 mm/297/16 " f: 1506 mm/595/16 " g: 455 mm/1715 /16" h: 1827 mm/7115 /16 " i: 35 mm/13/ 8"
3-1-1
Unpack.
Remove the developing unit. Apply toner to the cleaning blade (maintenance item U160)
Load developer.
Install the copy tray* and paper size label sheet. Check the toner sensor control voltage and toner feed start level (maintenance items U131 and U156).
3-1-2
2AD
Light source unit 1 pins
3-1-3
5 ^
6 4 % @
0 1 3 7 8
Figure 3-1-3 Unpacking 1 2 3 4 5 6 7 Copier Paper size label sheet Bottom pads Outer case Right pad Left pad Skid 8 9 0 ! @ # $ Inner frame Tray spacer Machine cover Hinge joint Bar code labels Plastic bag Drum set % ^ & * ( Top spacer Upper case Business reply mail*1 Power cord*2 Copy tray*2
*1: For 120 V specifications only. *2: For 220 - 240 V specifications only.
3-1-4
2AD Remove the tapes. 1. 2. 3. 4. 5. 6. 7. Remove the tape holding the front cover. Remove the two tapes holding the drawers. Remove the tape holding the right cover. Remove the tape holding the deck side cover. Open the front cover and remove the three tapes holding the SRDF. Remove the two tapes holding the power cord.* Remove the tape binding the power cord.
SRDF
Front cover
Drawers
3-1-5
2AD 8. 9. 10. 11. Remove the two tapes holding the DF original reversing cover. Remove the tape holding the paper ejection guide. Remove the three tapes holding the pins for light source units 1 and 2. Remove the tape holding the left cover.
DF original reversing cover Paper ejection guide
Left cover
Figure 3-1-5
3-1-6
2AD 12. Open the front cover and then the duplex unit. Remove the two tapes holding the duplex cover.
Duplex cover
Duplex unit
Figure 3-1-6 13. Open the drawers and remove the tape from each of them.
Figure 3-1-7
3-1-7
2AD 14. Open the SRDF and remove the paper from the contact glass. 15. Remove the protective film from the edge of the contact glass. 16. Remove the tape holding the original detection switch.
Figure 3-1-8 Remove pins holding light source units 1 and 2. 1. Remove the two pins for light source unit 1 and the pin for light source unit 2.
Figure 3-1-9
3-1-8
2AD Remove the developing unit. 1. Open the front cover. 2. Turn the paper transfer section release lever to the right.
Paper transfer section release lever
Figure 3-1-10
3-1-9
2AD 3. While pressing the image formation unit release button, pull the image formation unit out.
Image formation unit release button
Figure 3-1-11 4. Remove the two screws and open the image formation rail.
Screw Image formation rail Screw
Figure 3-1-12
3-1-10
2AD 5. Detach the 1-pin connector of the developing unit and 4-pin connector of the toner sub-hopper. 6. Slide the joint toward the machine rear. While sliding the shutter toward the machine front, close the shutter. 7. Lift the toner sub-hopper slightly and turn it toward the machine right.
Developing unit Shutter Joint
Toner sub-hopper
Figure 3-1-13 8. Hold the front and rear of the developing unit and remove it from the image formation unit.
Developing unit
3-1-11
2AD Load developer. 1. Remove the two screws and unlock the two hooks to remove the developing unit upper cover. Caution: Place the developing unit on a level surface when loading developer.
Hook
Screws
Hook
Figure 3-1-15 2. Shake the developer bottle well to agitate the developer. 3. While turning the developing gear in the direction of the arrow in the diagram, uniformly pour developer into the developing unit. Caution: Never turn the developing gear in the reverse direction.
Developing gear
Developer
Figure 3-1-16 Loading developer 4. Refit the developing unit upper cover using the two screws.
3-1-12
2AD Install the drum. 1. Remove the two screws and detach the main charger assembly. 2. Remove the two screws and open the upper cleaning cover.
Screw
Screw
Figure 3-1-17 3. Remove the screw from each of the front and rear drum retainers and then the retainers.
Screw
Figure 3-1-18
3-1-13
2AD 4. Fit the front and rear drum retainers to the drum and install the drum to the image formation unit. 5. Secure each of the front and rear drum retainers using the screws removed in step 3. When installing the drum, orient correctly with the thinner end of the drum flange shaft at the machine front and the thicker end at the machine rear.
Front drum retainer Drum Rear drum retainer
Screw
Screw
Figure 3-1-19 Installing the drum 6. Close the upper cleaning cover and secure using the two screws. 7. Fit the main charger assembly to the image formation unit and secure using the two screws. When installing the main charger assembly, fix with the assembly pushed all the way toward the machine front. 8. Fit the developing unit to the image formation unit. 9. Return the toner sub-hopper to the original position. 10. Open the shutter by sliding toward the machine rear and connect it to the joint. 11. Plug the 1-pin connector of the developing unit and 4-pin connector of the toner sub-hopper. 12. Close the image formation rail and secure using the two screws.
3-1-14
2AD 13. While pressing the image formation unit safety lock release plate, put the image formation unit back into the machine.
Image formation unit safety lock release plate Image formation unit
Figure 3-1-20 14. Return the paper transfer section release lever to the original position to secure the paper conveying section. Adjust the fixing pressure. 1. While lifting the fixing unit release lever, pull the fixing unit out from the machine.
Fixing unit release lever
Fixing unit
3-1-15
2AD 2. To adjust the fixing pressure, tighten the fixing pressure nuts on the front and rear of the fixing unit clockwise until each nut clamps the angle bracket against the locking nuts underneath.
Angle bracket
Figure 3-1-22 Adjusting the fixing pressure 3. While lifting the fixing unit release lever, slide the fixing unit back into the machine. 4. Close the front cover.
3-1-16
2AD Connect the power cord. 1. Connect the power cord to the machine.* 2. Insert the power plug into the wall outlet. Carry out initial developer setting (maintenance item U130). 1. Turn the main switch on and enter the maintenance mode by entering 10871087 using the numeric keys. The machine enters the maintenance mode immediately after the transfer charger wire cleaning completes. 2. Enter 130 using the numeric keys and press the print key. 3. Press the print key to execute the maintenance item. In approximately 2.5 minutes, the toner feed start level and toner sensor control voltage are automatically set and the settings displayed on the touch panel. Display example CONTROL: 156 (Toner sensor control voltage) TARGET: 100 (Toner feed start level) HUMID: 91 (Absolute humidity) 4. Press the stop/clear key. Check the toner sensor control voltage and toner feed start level (maintenance items U131 and U156). 1. Run maintenance items U131 and U156 and check that the values set in maintenance item U130 are displayed on the touch panel. 2. Press the stop/clear key. Apply toner to the cleaning blade (maintenance item U160) 1. Enter 160 using the numeric keys and press the print key. 2. Press the print key to execute the maintenance item. Toner is applied to the drum and then the drive stops automatically. 3. Press the stop/clear key.
3-1-17
2AD Release the cleaning blade. 1. Open the front cover. 2. Turn the paper transfer section release lever to the right to unlock the paper conveying section. 3. While pressing the image formation unit release button, pull the image formation unit out. 4. After checking that toner is applied to the drum, loosen the cleaning blade pin at the left of the image formation unit and slide the cleaning blade lever in the direction of the arrow. The cleaning blade is now unlocked and comes into contact with the drum. 5. Retighten the cleaning blade pin to secure the cleaning blade lever.
Figure 3-1-23 6. While pressing the image formation unit safety lock release plate, slide the image formation unit back into the machine. 7. Return the paper transfer section release lever to the original position to secure the paper conveying section. 8. Close the front cover. Exit maintenance mode. 1. Enter 001 using the numeric keys and press the print key. The machine exits the simulation mode. Install a toner cartridge. 1. Shake the toner cartridge upside-down and side-to-side to agitate the toner.
Figure 3-1-24
3-1-18
2AD 2. After the machine has stabilized, open the front cover. 3. Shift the toner cartridge release lever to the left.
Toner cartridge release lever
Figure 3-1-25 4. Insert the toner cartridge by aligning the two arrows on the top of the toner cartridge with the two markings on the machine. 5. Shift the toner cartridge release lever to the right to secure the toner cartridge.
Markings Toner cartridge Toner cartridge release lever
3-1-19
2AD Adjust the height adjusters. 1. Turn the four height adjusters at the bottom of the machine so that the machine is level.
Height adjuster
Figure 3-1-27 Install the copy tray* and paper size label sheet. 1. Install the copy tray.* 2. Load paper so that the copying side (the side facing upward when unpacked) faces downward. When loading paper on the bypass table, load so that the copying side (the side facing upward when unpacked) faces upward. Loading paper upside down may cause a paper jam.
Copying side (side facing upward when unpacked)
3-1-20
2AD 3. Slide the paper size label sheet into the front of drawer.
Figure 3-1-29 4. If the user requests the side guides to be fixed, fix according to the paper size using four M3 8 flat-head screws.
Screws Side guides
Screws
Figure 3-1-30 5. Set the paper size on the operation panel.* Make test copies. 1. Place an original and make test copies. Check if the center lines of the large paper deck, the bypass table and each drawer are correct. If not, adjust the center lines. Completion of the machine installation. * For 220 - 240 V specifications only.
3-1-21
2AD
Contents Switching between double and single counts Turning auto start function on/off Setting auto clear time Turning auto preheat/energy saver function on/off Switching copy operation at toner empty detection Changing the copy count timing Switching between duplex/simplex copy mode Setting preheat/energy saver mode Setting auto drawer size detection Setting the copy density adjustment range
Factory setting Double count ON 90 ON SINGLE MODE, 0 EJECT Simplex copy Energy Star ON (inch) OFF (metric) SPECIAL AREA
3-1-22
2AD
Figure 3-1-31
3-1-23
2AD 4. Remove the six screws holding the sequence cover and then the cover.
Figure 3-1-32 5. Fit an image memory into the add-on memory slot on the memory copy PCB.
Memory copy PCB 2
1 2
Image memory
Figure 3-1-33
3-1-24
2AD
Cable holes
Connector
Figure 3-1-34
3-1-25
2AD 10. Route the dehumidifier relay cable using the five wire saddles. 11. Insert the 2-pin connector of the optical heater into the 2-pin connector of the dehumidifier relay cable. 12. Insert the 2-pin connector of the main PCB into the 2-pin connector of the dehumidifier relay cable. 13. Insert the 4-pin connector of the main PCB into the 4-pin connector of the dehumidifier relay cable.
Wire saddle
Main harness
Wire saddle
1-pin connectors
Figure 3-1-35
3-1-26
2AD 14. 15. 16. 17. 18. Remove the two screws holding the lower left cover and then the cover. Remove the cap in the lower left cover. Refit the lower left cover using the two screws. Insert the heater switch instead. Plug the two 1-pin connectors of the dehumidifier relay cable onto the terminals of the heater switch.
Cap
1-pin connector
3-1-27
2AD
Drawer heater
Figure 3-1-37
3-1-28
2AD 7. 8. 9. 10. Detach the SRDF connector. Remove the six screws holding the rear cover and then the cover. Route the dehumidifier relay cable using the five wire saddles. Insert 2-pin connector of the drawer heater into the 2-pin connector of the dehumidifier relay cable. 11. Insert the 2-pin connector of the main harness into the 2-pin connector of the dehumidifier relay cable. 12. Insert the 4-pin connector of the main harness into the 4-pin connector of the dehumidifier relay cable.
Wire saddle
Wire saddle
Dehumidifier relay cable 4-pin connector 4-pin connector 2-pin connector 2-pin connector Wire saddle
Main harness
Wire saddle
Figure 3-1-38
3-1-29
2AD 13. 14. 15. 16. 17. Remove the two screws holding the lower left cover and then the cover. Remove the cap in the lower left cover. Refit the lower left cover using the two screws. Insert the heater switch instead. Plug the two 1-pin connectors of the dehumidifier relay cable onto the terminals of the heater switch.
Cap
1-pin connector
3-1-30
2AD
M4 6 screws (B4304060)
Figure 3-1-40
3-1-31
2AD 3. 4. 5. 6. Remove the screw holding right front lower cover B and then the cover. Remove the screw holding the right rear lower cover and then the cover. Remove the two screws and detach the middle right cover from the machine. Cut out the aperture plate on the middle right cover using nippers.
Screw
Aperture plate
Screw
Figure 3-1-41
3-1-32
2AD 7. Pass the 4-pin connector of the key counter through the apertures in the key counter cover retainer and middle right cover, and insert into the 4-pin connector inside the machine. 8. Seat the projection of the key counter cover retainer in the aperture in the middle right cover, and fasten them both to the machine using the two screws. 9. Refit the screw to the machine front side of the middle right cover. 10. Fit the key counter cover with the key counter assembly inserted to the key counter cover retainer on the machine.
Aperture Middle right cover Key counter cover retainer (66060021) M4 10 screw (B4304100) Key counter cover
M4 10 screw (B4304100)
Figure 3-1-42 11. 12. 13. 14. 15. Insert the key counter into the key counter assembly. Turn the main switch on and enter the maintenance mode. Run maintenance item U204 and select KEY COUNTER. Exit the maintenance mode. Check that the message requesting the key counter to be inserted is displayed when the key counter is pulled out. 16. Check that the counter counts up as copies are made.
3-1-33
2AD
Screws
Screws
Figure 3-1-43 2. Remove the two screws from each of the deck right cover, deck left cover and deck rear cover and then the covers. 3. Open the large paper deck. 4. Detach the deck paper conveying motor connector. 5. Remove the spring from the deck paper conveying motor bracket. 6. Remove the four screws holding the deck paper conveying motor bracket and then the bracket. 7. Remove the two screws holding the deck paper conveying unit assembly and then the assembly.
Spring Connector Screws
Screws
Figure 3-1-44
3-1-34
2AD 8. Fit the dehumidifier heater assemblies to the right and left of the large paper deck using two screws for each.
Screws Screws
Figure 3-1-45 9. Fit the edgings to the two U-shaped cutouts in the rear frame. 10. Pull the dehumidifier heater wires out to the machine rear through the edgings.
Edging Edging
Figure 3-1-46
3-1-35
2AD 11. Detach the open connector from the connector of the main wire on the machine rear.
Main wire
Open connector
Figure 3-1-47 12. Insert the dehumidifier heater connectors into the relay wire connectors (see A in Figure 3-1-48). 13. Insert the main wire connector into the relay wire connector (see B in Figure 3-148). 14. Tidy up the large paper deck wires and relay wire using the six bands and route the wires while clipping the bands into holes in the rear frame.
A
Main wire
Bands Band
Relay wire
Band
Bands
3-1-36
2AD
1-1-19
2AD
Enter 10871087.
Enter the number of the maintenance item to be executed using the numeric or Up/Down keys.
Yes
No
Yes
No Enter 001 using numeric or Up/Down Exiting the maintenance mode keys, and press the print key.
End
3-2-1
2AD Data setting Data is changed by pressing the Up/Down keys, and the new data is set by pressing the print key. In a maintenance item where multiple items can be changed, the item to be changed is selected by pressing on it on the touch panel.
U035 330
Metric
/C
1 6 2
Inch
Stop/ Clear
4
Figure 3-2-1
1 Adjustment window Displays the data to be set. 2 Up/Down keys Changes the setting. 3 Items Displays the selected item in reverse. 4 Current setting Displays the previously set data by pressing the print key. 5 Print key Sets the changed setting. 6 Stop/clear key Cancels the change.
3-2-2
2AD Operation execution The specified operations and auto adjustments are performed by pressing the print key. In a maintenance item where multiple operations can be performed, the item to be executed is selected by pressing on it on the touch panel. Metric
/C
U030
MAIN MOTOR
3
Stop/ Clear
3
Figure 3-2-2 1 Items Displays the selected item in reverse. 2 Print key Starts operation. 3 Stop/clear key Stops operation.
Interrupt copy mode Outputting a test copy or VTC pattern is required in some maintenance items. Such an output is enabled by pressing the interrupt key to enter interrupt copy mode. However, since this function is restricted depending on maintenance items, only outputting may be enabled, or a test copy even from an original may not be as good as that made in normal copy mode. To return the screen from interrupt copy mode to maintenance mode, press the interrupt key again.
3-2-3
2AD-1 2AD ( 2 ) Maintenance mode item list Section General Item No. U000 U001 U003 U004 U005 U019 Initialization U020 U021 U022 Drive, paper feed, paper conveying and cooling system U030 U031 U032 U033 U034 Maintenance item contents Outputting an own-status report Exiting the maintenance mode Setting the service telephone number Setting the machine number Copying without paper Displaying the ROM version Initializing all data Initializing memories Initializing backup data Checking motor operation Checking switches for paper conveying Checking clutch operation Checking solenoid operation Adjusting the print start timing Adjusting leading edge registration Adjusting leading edge registration (second face) Adjusting the print center line Setting folio size Length Width Setting envelope size Length Width Adjusting the amount of slack in the paper before registration Drawer feed Bypass feed Duplex feed Adjusting the side margins for duplex copying Performing fine adjustment of the motor speed Drive motor/paper conveying motor Adjusting the scanner input properties Text/text and photo/photo mode Turning the exposure lamp on Adjusting the shading position Adjusting the scanner magnification Main scanning direction/auxiliary scanning direction Initial setting*
4 0 0
330 210 242 162
U035
U036
U051
20 5 25 0 8 12 0 0
3-2-4
2AD Item No. U066 U067 U070 U071 U072 U073 U088 U089 U091 U092 U093 U099 High voltage U100 U101 Initial setting* 0 0 0 0 0 OFF 0 150 220/57 140 100 1 153 ON 114 20
Section Optical
Maintenance item contents Adjusting the scanner leading edge registration Adjusting the scanner center line Adjusting the DF magnification Adjusting the DF scanning timing Adjusting the DF center line Checking scanner operation Setting the input filter (moir reduction mode) Outputting a PG pattern Checking shading Adjusting the scanner automatically Setting the exposure density gradient Text/text and photo/photo mode Checking and initializing the original size detection sensors Setting the surface potential Setting high voltages Developing bias Transfer voltage Separation voltage Setting the cleaning interval for the transfer charger Checking/clearing the drum count Checking/clearing the drum drive time Initial setting for the developer Setting the toner sensor control voltage Replenishing toner forcibly Collecting the recycled toner Checking toner motor operation Turning the toner level detection function on/off Checking the toner level detection sensor Displaying the toner sensor output Changing the toner control level Toner feed start level Toner empty level Checking/clearing the developing drive time Checking/clearing the developing count
U102 U110 U111 Developing U130 U131 U132 U133 U135 U136 U137 U155 U156
U157 U158
3-2-5
2AD-1 2AD Item No. Initial setting* 190 175 190 120 ON OFF 0 75000 150 SINGLE COUNT ON 120 ON SINGLE MODE, 0 EJECT
Section
Maintenance item contents Applying toner to the cleaning blade Setting the fixing control temperature Normal stabilization control temperature Primary stabilization temperature Secondary stabilization temperature Aging time after secondary stabilization Stabilizing fixing forcibly Turning the fixing heater on Setting the fixing phase control Turning all LEDs on Initializing the touch panel Setting the MMD host monitoring system Operating DF separately Setting the presence or absence of a key card or key counter Setting the presence or absence of the coin vender Setting date and time Checking the operation of the DF motors, clutches and solenoids Checking the DF switches Checking messages Checking the operation of the large paper deck and paper feed desk Setting the paper eject device Adjustment of the amount of slack in the paper in punch mode Punch limit Punch-hole scrap count Setting the maintenance cycle Checking/clearing the maintenance count Setting the destination Switching between double and single counts Turning auto start function on/off Setting auto clear time Turning auto preheat/energy saver function on/off Switching copy operation at toner empty detection Changing the copy count timing
U162 U196 U198 Operation U200 panel and U201 support equipment U202 U203 U204 U206 U209 U243 U244 U245 U247 U248
Mode setting
3-2-6
2AD Item No. U343 U344 U345 U347 U348 Image U402 processing U403 U404 Others U901 U904 U905 U906 U990 U992 Initial setting* OFF Energy Star applied 0 ON NORMAL
Maintenance item contents Switching between duplex/simplex copy mode Setting preheat/energy saver mode Setting the value for maintenance due indication Setting auto drawer size detection Setting the copy density adjustment range Adjusting margins in image printing Adjusting margins for reading an original on the contact glass Adjusting margins for DF original reading Checking/clearing copy counts by paper feed locations Checking/clearing the service call counts Checking/clearing counts by optional devices Resetting partial operation control Checking/clearing the time for the exposure lamp to light Checking/clearing the printer count
3-2-7
2AD ( 3 ) Contents of maintenance mode items Maintenance item No. U000 Description Outputting an own-status report Description Outputs lists of the current settings of the maintenance modes, and paper jam and service call occurrences. Purpose To check the current setting of the maintenance modes, or paper jam or service call occurrences. Before initializing or replacing the backup RAM, output a list of the current settings of the maintenance modes to reenter the settings after initialization or replacement. Method 1 Press the print key. The screen for selecting an item is displayed. 2 Select the item to be output. The selected item is displayed in reverse. Display MAINTENANCE JAM SERVICE CALL Output list List of the current settings of the maintenance modes List of the paper jam occurrences List of the service call occurrences
3 Press the print key. The interrupt copy mode is entered and a list is output. When A4/11" 81/2" paper is available, a report of this size is output. If not, specify the paper feed location. When output is complete, the screen for selecting an item is displayed. Completion Press the stop/clear key at the screen for selecting an item. The screen for selecting a maintenance item No. is displayed.
3-2-8
Description Exiting the maintenance mode Description Exits the maintenance mode and return to the normal copy mode. Purpose To exit the maintenance mode. Method Press the print key. The normal copy mode is entered.
U003
Setting the service telephone number Description Sets the telephone number to be displayed when a service call code is detected. Purpose To set the telephone number to call service when installing the machine. Method Press the print key. The currently set telephone number is displayed. Setting 1 Enter a telephone number (up to 15 digit) using the numeric keys. To enter symbols such as hyphens and parentheses, select as required from the symbols displayed on the touch panel as shown below. To move the cursor, press either of the arrows in the bottom row. * # ( ) (Space) 2 Press the print key. The phone number is set, and the screen for selecting a maintenance item No. is displayed. Completion To exit the maintenance mode without changing the current setting, press the stop/clear key. The screen for selecting a maintenance item No. is displayed.
3-2-9
2AD Maintenance item No. U004 Setting the machine number Description Displays and changes the machine number. Purpose To check or set the machine number. Method Press the print key. The currently set machine number is displayed. Setting 1 Enter the last six digits of the machine number using the numeric key. Do not enter the first two digits, 3 and 7. 2 Press the print key. The machine number is set. Completion To exit the maintenance mode without changing the current setting, press the stop/clear key. The screen for selecting a maintenance item No. is displayed.
Description
3-2-10
2AD Maintenance item No. U005 Copying without paper Description Simulates the copy operation without paper feed. Purpose To check the overall operation of the machine. Method 1 Press the print key. The screen for selecting an item is displayed. 2 Select the item to be operated. The selected item is displayed in reverse. Display PPC PPC + DF Operation Only the copier operates. Both the copier and SRDF operate (continuous operation).
Description
3 Press the interrupt key. The copy mode screen is displayed. 4 Set the operation conditions required on the copy mode screen. Changes in the following settings can be made. Paper feed locations Magnifications Simplex or duplex copy modes Number of copies: in simplex copy mode, continuous copying is performed when set to 999; in duplex copy mode, continuous copying is performed regardless of the setting. Copy density Keys on the operation panel other than the energy saver key 5 To control the paper feed pulley, remove all the paper in the drawers, or the drawers. With the paper present, the paper feed pulley does not operate. 6 Press the print key. The operation starts. Copy operation is simulated without paper under the set conditions. When operation is complete, the screen for selecting an item is displayed. 7 To stop continuous operation, press the stop/clear key. Completion Press the stop/clear key at the screen for selecting an item. The screen for selecting a maintenance item No. is displayed.
3-2-11
2AD Maintenance item No. U019 Displaying the ROM version Description Displays the part number of the ROM fitted to each PCB. Purpose To check the part number or to decide if the ROM version is new from the last digit of the number. Method 1 Press the print key. The last six digits of the part number indicating the ROM version are displayed. 2 Change the screen using The Up/Down keys. Display MAIN ENGINE MMI FONT SCANNER MEM1 MEM2 Description Main ROM IC Engine ROM IC Operation ROM IC Font ROM IC Scanner ROM IC Memory copy ROM IC Memory copy ROM IC
Description
Completion Press the stop/clear key. The screen for selecting a maintenance item No. is displayed. U020 Initializing all data Description Initializes all the backup RAM on the main PCB to return to the original settings. Purpose Used when replacing the backup RAM on the main PCB. Method 1 Press the print key. The screen for executing is displayed. 2 Press EXECUTE on the touch panel. It is displayed in reverse. 3 Press the print key. All data in the backup RAM is initialized, and the original settings for Japan specifications are set. When initialization is complete, the machine automatically returns to the same status as when the main switch is turned on. Completion To exit the maintenance mode without executing initialization, press the stop/clear key. The screen for selecting a maintenance item No. is displayed.
3-2-12
2AD Maintenance item No. U021 Initializing memories Description Initializes the setting data other than that for adjustments due to variations between respective machines, i.e., settings for counters, service call code detection and modes. As a result, initializes the backup RAM according to the specifications depending on the destination selected in U252. Purpose Used to return the machine settings to the factory settings. Method 1 Press the print key. The screen for executing is displayed. 2 Press EXECUTE on the touch panel. It is displayed in reverse. 3 Press the print key. All data other than that for adjustments due to variations between machines is initialized. When initialization is complete, the machine automatically returns to the same status as when the main switch is turned on. Completion To exit the maintenance mode without executing initialization, press the stop/clear key. The screen for selecting a maintenance item No. is displayed.
Description
3-2-13
2AD-1 2AD Maintenance item No. U022 Initializing backup data Description Initializes only the data set for the optical section. Purpose To be executed after replacing the scanner unit. Method 1 Press the print key. The screen for executing is displayed. 2 Press SCANNER on the touch panel. EXECUTE is displayed. 3 Press EXECUTE on the touch panel. It is displayed in reverse. 4 Press the print key. The data for the optical section (U060 to 099, U403, U404 and U990) is initialized. Completion To exit the maintenance mode, press the stop/clear key. The screen for selecting a maintenance item No. is displayed.
Description
3-2-14
2AD Maintenance item No. U030 Checking motor operation Description Drives each motor. Purpose To check the operation of each motor. Method 1 Press the print key. The screen for selecting an item is displayed. 2 Select the motor to be operated. The selected item is displayed in reverse and the operation starts. Display MAIN MOTOR CONV MOTOR FEED MOTOR Operation The drive motor operates and developing bias is applied. The paper conveying motor operates. The paper feed motor operates.
Description
3 To stop operation, press the stop/clear key. Completion Press the stop key after operation stops. The screen for selecting a maintenance item No. is displayed.
3-2-15
Description Checking switches for paper conveying Description Displays the on-off status of each paper detection switch on the paper path. Purpose To check if the switches for paper conveying operate correctly. Method 1 Press the print key. A list of the switches, the on-off status of which can be checked, are displayed. 2 Turn each switch on and off manually to check the status. When the on-status of a switch is detected, that switch is displayed in reverse. Display FEED1 SW FEED2 SW FEED3 SW FEED4 SW FEED SW R SW EJE SW BRA SW REV SW DUP PESW DUP1 SW DUP2 SW DUP3 SW Switches Paper feed switch 1 (PFSW1) Paper feed switch 2 (PFSW2) Paper feed switch 3 (PFSW3) Paper feed switch 4 (PFSW4) Feed switch (FSW) Registration switch (RSW) Eject switch (ESW) Feedshift switch (FSSW) Switchback eject switch (SBESW) Stock switch (STKSW) Duplex registration switch (DUPRSW) Duplex paper conveying switch (DUPPCSW) Duplex eject switch (DUPESW)
Completion Press the stop/clear key. The screen for selecting a maintenance item No. is displayed.
3-2-16
2AD Maintenance item No. U032 Checking clutch operation Description Turns each clutch on. Purpose To check the operation of each clutch. Method 1 Press the print key. The screen for selecting an item is displayed. 2 Select the clutch to be operated. The selected item is displayed in reverse, and the clutch turns on for 1 s. Display SB FEED F FEED S FEED FEED L FEED H FEED 1 FEED 2 FEED 3 REGIST EJECT SP Clutches Bypass paper feed clutch (BYPPFCL) Upper paper feed clutch (PFCL-U) Lower paper feed clutch (PFCL-L) Feed clutch 5 (FCL5) Feed clutch 4 (FCL4) Feed clutch 1 (FCL1) Feed clutch 2 (FCL2) Feed clutch 3 (FCL3) Registration clutch (RCL) Eject speed switching clutch (ESCL)
Description
3 To turn each clutch on while a motor is driving, press the interrupt key before selecting the clutch. The drive motor, paper feed motor and paper conveying motor turn on, and the selected clutch remains on until the stop/clear key is pressed. If the upper or lower paper feed clutch is turned on while a motor is driving, paper is conveyed by the rotation of the paper feed pulley, resulting in a paper jam. Be sure to remove the paper drawers before turning either of these clutches on. 4 To stop the motor drive, press the interrupt copy key. Completion Press the stop/clear key. The screen for selecting a maintenance item No. is displayed.
3-2-17
2AD Maintenance item No. U033 Checking solenoid operation Description Turns each solenoid on. Purpose To check the operation of each solenoid. Method 1 Press the print key. The screen for selecting an item is displayed. 2 Select the solenoid to be operated. The selected item is displayed in reverse, and the solenoid turns on for 1 s. Display SB LIFT BRANCH END PRE TRAY FEE TRAY CHG MSW OFF Solenoids Bypass solenoid (BYPSOL) Feedshift solenoid (FSSOL) Duplex paper tapping solenoid (DUPPTSOL) Duplex forwarding solenoid (DUPFWDSOL) Switchback feedshift solenoid (SBFSSOL) The main switch turns off.
Description
MSW OFF is selected when the operation of the main switch is checked in auto shutoff mode. Completion Press the stop/clear key. The screen for selecting a maintenance item No. is displayed. U034 Adjusting the print start timing Adjustment See pages 3-3-18 and 19.
3-2-18
2AD Maintenance item No. U035 Setting folio size Description Changes the image area for copying onto folio size paper. Purpose To prevent the image at the trailing edge, or right or left side of the paper from not being copied by setting the actual size of the folio paper used. Method Press the print key. The screen for selecting an item is displayed. Setting 1 Select the item to be set. The selected item is displayed in reverse, and the current setting is displayed in the adjustment window. 2 Change the setting using the Up/Down keys. Display Setting Setting range Initial setting LENGTH DATA Length 330 to 356 mm 330 WIDTH DATA Width 220 to 220 mm 210 3 Press the print key. The value is set. Completion Press the stop/clear key. The screen for selecting a maintenance item No. is displayed. U036 Setting envelope size Description Changes the image area for printing onto an envelope when the optional printer unit is installed. Purpose To prevent the image at the trailing edge, or right or left side of the paper from not being printed by setting the actual size of the envelop used. Method Press the print key. The screen for selecting an item is displayed. Setting 1 Select the item to be set. The selected item is displayed in reverse, and the current setting is displayed in the adjustment window. 2 Change the setting using the Up/Down keys. Display Setting Setting range Initial setting LENGTH DATA Length 162 to 242 mm 242 WIDTH DATA Width 98 to 162 mm 162 3 Press the print key. The value is set. Completion Press the stop/clear key. The screen for selecting a maintenance item No. is displayed.
Description
3-2-19
2AD Maintenance item No. U051 Adjustment See page 3-3-22. U052 Adjusting the side margins for duplex copying Adjustment See page 3-3-87. U053 Performing fine adjustment of the motor speed Description Performs fine adjustment of the speeds of the drive motor and paper conveying motor. Purpose Used to adjust the speed of the respective motors when the magnification in the auxiliary scanning direction is not correct after the motor is replaced. Method Press the print key. The screen for selecting an item is displayed. Setting 1 Select the item to be set. The selected item is displayed in reverse, and the current setting is displayed in the adjustment window. 2 Change the setting using the Up/Down keys. Display Description Setting range Initial setting MAIN MOTOR Drive motor speed adjustment 0 to 14 8 CONV MOTOR Paper conveying motor speed adjustment 0 to 14 8 Increasing the setting makes the motor speed faster and the image longer, and decreasing it makes the speed slower and the image shorter. 3 Press the print key. The value is set. Interrupt copy mode While this maintenance item is being performed, a VTC pattern shown below is output in interrupt copy mode. Correct values for an A3/11" x 17" output are: A = 150 mm B = 300 mm
A B
Figure 3-2-3
3-2-20
Description Adjustment 1 Output an A3/11" 17" VTC pattern in interrupt mode. 2 Measure A and B on the VTC pattern (Figure 3-2-3), and perform the following adjustments if they are different from the correct sizes: A: Drive motor adjustment B: Paper conveying motor adjustment Completion Press the stop/clear key. The screen for selecting a maintenance item No. is displayed.
U060
Adjusting the scanner input properties Description Adjusts the image scanning density in text, text and photo, or photo mode. Purpose Used when the entire image appears too dark or light in the specified mode. Method Press the print key. The screen for selecting an item is displayed. Setting 1 Select the item to be set. The selected item is displayed in reverse, and the current setting is displayed in the adjustment window. 2 Change the setting using the Up/Down keys.
Description Density in text mode Density in text and photo mode Density in photo mode
Setting range 0 to 23 0 to 23 0 to 23
Initial setting 12 12 12
Increasing the setting makes the density lower, and decreasing it makes the density higher.
3 Press the print key. The value is set. Interrupt copy mode While this maintenance item is being performed, copying from an original can be made in interrupt copy mode. Completion Press the stop/clear key. The screen for selecting a maintenance item No. is displayed. Supplement The following settings are also reset to the initial values by performing this maintenance item: Exposure density gradient set in maintenance mode (U093) Auto and manual exposure set in the copy default item of the copier management mode
3-2-21
2AD Maintenance item No. U061 Description Turns the exposure lamp on. Purpose To check the exposure lamp. Method 1 Press the print key. The screen for selecting an item is displayed. 2 Press the print key. The exposure lamp lights. 3 To turn the exposure lamp off, press the stop/clear key. Completion Press the stop/clear key. The screen for selecting a maintenance item No. is displayed. U063 Adjusting the shading position Description Changes the shading position. Purpose Used when white lines continue to appear longitudinally on the image after the shading plate is cleaned. This is due to flaws or stains inside the shading plate. To prevent this problem, the shading position should be changed so that shading is possible without being affected by the flaws or stains. Method 1 Press the print key. The screen for adjustment is displayed. 2 Change the setting using the Up/Down keys. Description Shading position Setting range Initial setting Change in value per step 2 to +2 0 0.17 mm
Increasing the setting moves the shading position toward the machine right, and decreasing it moves the position toward the machine left. 3 Press the print key. The value is set. Interrupt copy mode While this maintenance item is being performed, copying from an original can be made in interrupt copy mode. Completion Press the stop/clear key. The screen for selecting a maintenance item No. is displayed.
3-2-22
2AD Maintenance item No. U065 Adjustment See pages 3-3-34 and 35. U066 Adjusting the scanner leading edge registration Adjustment See page 3-3-37. U067 Adjusting the scanner center line Adjustment See page 3-3-36. U070 Adjusting the DF magnification Adjustment See page 3-3-95. U071 Adjusting the DF scanning timing Adjustment See page 3-3-97. U072 Adjusting the DF center line Adjustment See page 3-3-96.
3-2-23
2AD Maintenance item No. U073 Checking scanner operation Description Simulates the scanner operation under arbitrary conditions. Purpose To check scanner operation. Method 1 Press the print key. The screen for selecting an item is displayed. 2 Select the item to be changed. The selected item is displayed in reverse. 3 Change the setting using the Up/Down keys. Display ZOOM SIZE LAMP Operating conditions ZOOM Magnification Original size LAMP on and off of the exposure lamp Setting range 25 to 400% See below. 0 (off) or 1 (on)
Description
Original sizes for each setting in SIZE Setting 8 9 18 36 39 40 41 Original size A4 B5 11" 81/2" A3 B4 A4R B5R Setting 42 47 52 53 55 56 58 Original size A5R Folio 11" 17" 11" 15" 81/2" 14" 81/2" 11" 51/2" 81/2"
4 Press the print key. Scanning starts under the selected conditions. 5 To stop operation, press the stop/clear key. Completion Press the stop/clear key when scanning stops. The screen for selecting a maintenance item No. is displayed.
3-2-24
Description Setting the input filter (moir reduction mode) Description Turns moir reduction mode on and off by switching the input filter on and off. Purpose Used to prevent regular density unevenness (moir) on halftone image areas of the copy image in text mode and text and photo mode. Such moir is more likely to appear when an enlargement or reduction copy is made in text mode from an original containing large halftone image areas. Method Press the print key. The screen for selecting an item is displayed. Setting 1 Select ON or OFF. The selected item is displayed in reverse. Display Description ON Moir reduction mode OFF Normal copy mode Initial setting: OFF If moir on the copy image is significant, change the setting to ON. Note that when the moir reduction mode is turned on, the resolution may be slightly reduced. 2 Press the print key. The value is set. The screen for selecting a maintenance item No. is displayed. Completion To exit the maintenance mode without changing the current setting, press the stop/clear key. The screen for selecting a maintenance item No. is displayed.
3-2-25
2AD Maintenance item No. U089 Outputting a PG pattern Description Selects and outputs the PG pattern created in the copier. Purpose When performing respective image printing adjustments, used to check the machine status apart from that of the scanner with a non-scanned output PG pattern. Method 1 Press the print key. The screen for selecting an item is displayed. 2 Select the PG pattern to be output. Display GRAYSCALE PG pattern to be output Purpose To check the laser scanner unit engine output characteristics.
Description
MONO-LEVEL
256-LEVEL
1 DOT-LINE
To check fine line reproducibility. To adjust the position of the laser scanner unit (lateral squareness)
3-2-26
Description 3 To change the output conditions for MONO-LEVEL, change the setting using The Up/Down keys. Description Setting range Initial setting Output conditions 0 to 255 0 for MONO-LEVEL Increasing the setting makes the density higher, and decreasing it makes the density lower. Entirely white paper is output when the setting is 0, and entirely black paper is output when it is 255. 4 Press the interrupt key. The screen for copy mode is displayed. 5 Press the print key. A PG pattern is output. Completion Press the stop/clear key at the screen for selecting an item. The screen for selecting a maintenance item No. is displayed.
3-2-27
2AD Maintenance item No. U091 Checking shading Description Performs scanning under the same conditions as before and after shading is performed, displaying the original scanning values at nine points of the contact glass on the touch panel. Purpose To check the change in original scanning values before and after shading. The results may be used to decide the causes for fixing unevenness (uneven density) of the gray area of an image: either due to optical (shading or CCD) or other problems. Also to check the causes for a white or black line appearing longitudinally.
Description
3-2-28
Description Method 1 Press the print key. The screen for selecting an item is displayed.
2 Select the item to be operated. The selected item is displayed in reverse. Display Operation SHD BEFORE Performs scanning before shading and displays the result. SHD AFTER Performs scanning after shading and displays the result. 3 Press the print key. Operation starts. Scanning is performed under the selected conditions and the result is displayed. When scanning is performed before shading, the scan value at the machine center should be slightly different from those at the machine front and rear. When scanning is performed after shading, there should be no difference between respective values. Any differences between the values at machine front and rear indicates that scanner problem causes the fixing unevenness. If the displayed results indicate no shading problems, the fixing unevenness (uneven copy density) is caused by factors other than in the scanner section (shading or CCD). If a black line appears, the cause may assumed to be based on the results of the scanning operation before shading: if a white line appears, they may be assumed based on the results of the scanning operation after shading. Note that depending on the thickness and location of the black or white line, it may not be possible to use this method to determine the cause. This is because the displayed values obtained from scanning at the limit of nine points are insufficient to provide significant information. 20 mm from the machine left 200 mm from the machine left 400 mm from the machine left
: : :
100 mm from the machine Machine center center toward machine front 100 mm from machine center toward machine rear Figure 3-2-4 4 Press the stop/clear key. The screen for selecting an item is displayed. Completion Press the stop/clear key. The screen for entering a maintenance item is displayed.
3-2-29
Description Adjusting the scanner automatically Description Makes auto scanner adjustments in the order below using the specified original. Adjusting the scanner center line (U067) Adjusting the scanner magnification in the main scanning direction (U065) Adjusting the scanner leading edge registration (U066) Adjusting scanner magnification in the auxiliary direction (U065) When this maintenance item is performed, the settings in U065, U066 and U067 are also changed. Purpose Used to make respective auto adjustments for the scanner. Method 1 Place the specified original (P/N: 2AC68240) on the contact glass. 2 Press the print key. The screen for executing is displayed. 3 Press the print key. Auto adjustment starts. When adjustment is complete, each adjusted value is displayed. Display SCAN CENTER ADJ MAIN SCAN ADJ SCAN TIMING ADJ SUB SCAN ADJ Description Scanner center line Scanner magnification in the main scanning direction Scanner leading registration Scanner magnification in the auxiliary direction
If a problem occurs during auto adjustment, an error code is displayed and operation stops. Should this happen, determine the details of the problem and either repeat the procedure from the beginning, or adjust the remaining items manually by running the corresponding maintenance items.
Completion Press the stop/clear key after auto adjustment is complete. The screen for selecting a maintenance item is displayed. If the stop/clear key is pressed during auto adjustment, adjustment stops and no settings are changed.
3-2-30
Description Setting the exposure density gradient Description Changes the exposure density gradient in manual density mode, depending on respective image modes (text, text and photo, photo). Purpose To set how the image density is altered by a change of one step in the manual density adjustment. Also used to make copy image darker or lighter. Start 1 Press the print key. The screen for selecting an item is displayed. 2 Select the image mode to be adjusted. The screen for the selected item is displayed. Display Description TEXT Density in text mode MIXED Density in text and photo mode PHOTO Density in photo mode Setting 1 Select the item to be adjusted. The selected item is displayed in reverse and the current setting is displayed in the adjustment window. 2 Adjust the setting using the Up/Down keys.
Description Change in density when manual density is set dark Change in density when manual density is set light
Increasing the setting makes the change in density larger, and decreasing it makes the change smaller. Image density Dark Setting: 3 Setting: 0
Set to LIGHTER
Set to DARKER
Density adjustment range: Normal Density adjustment range: Special area Figure 3-2-5 Exposure density gradient
3-2-31
Description 3 Press the print key. The value is set. 4 To return to the screen for selecting an item, press the stop/clear key. Interrupt copy mode While this maintenance item is being performed, copying from an original can be made in interrupt copy mode. Completion Press the stop/clear key at the screen for selecting an item. The screen for selecting a maintenance item No. is displayed.
U099
Checking and initializing the original size detection sensors Description Displays the on-off status of the original size detection sensors. Also initializes and displays the data for the respective sensors. Purpose To check if the original size detection sensors operate correctly. Also to initialize the respective sensors after they are replaced. The respective sensors are arranged as shown below.
A3/11" 17" 11" 15"
Folio
B4
OSD7 OSD8
A4/11" 81/2"
Figure 3-2-6 Arrangement of the original size detection sensors Start 1 Press the print key. The screen for selecting an item is displayed. 2 Select the item to be checked or initialized. The screen for executing is displayed. Display INDICATION INITIALIZING ADJUST Description Checking sensor operation Initializing the sensor Displaying the sensor data
3-2-32
Description Method to check sensor operation A list of sensors and switches for on-off status checking is displayed. 1 Check the on-off status of a sensor by placing an original on the contact glass. If on-status is detected, the corresponding switch or sensor is displayed in reverse. Display SENS 1 SENS 2 SENS 3 SENS 4 SENS 5 SENS 6 SENS 7* SENS 8* MAT SW Sensor or switch Original size detection sensor 1 (OSD1) Original size detection sensor 2 (OSD2) Original size detection sensor 3 (OSD3) Original size detection sensor 4 (OSD4) Original size detection sensor 5 (OSD5) Original size detection sensor 6 (OSD6) Original size detection sensor 7 (OSD7) Original size detection sensor 8 (OSD8) Original detection switch (ODSW)
* For metric specifications only. 2 To return to the screen for selecting an item, press the stop clear key. Method to initialize the sensors 1 Place ten sheets of A3/11" x 17" paper on the contact glass. 2 Press INITIALIZING on the touch panel. 3 Press the start key to initialize. All sensors are initialized, and the initial scanned data is set. To check the initial scanned data, select the number of a sensor using Up/Down keys. 4 To return to the screen for selecting an item, press the stop/clear key. Method to display the data for the sensor 1 Selects the number of the sensor to be checked using the Up/Down keys. The data for the sensor is displayed. Display ADJUST DATA INITIAL DATA Description Transmission data for a sensor Initial scanned data for a sensor
2 To return to the screen for selecting an item, press the stop/clear key. Completion Press the stop/clear key at the screen for selecting an item. The screen for maintenance item No. is displayed.
3-2-33
2AD Maintenance item No. U100 Setting the surface potential Description Changes the surface potential by changing the grid control voltage. Also performs main charging. Purpose To set the surface potential or check main charging. Also used when reentering data after replacing the backup RAM or initializing the set data. Start Press the print key. The screen for selecting an item is displayed. Display Description MC DATA Changing the grid control voltage MC ON Turning the main charger on MC ON/OFF Turning the main charger on and off LASER ON/OFF Turning the main charger on and the laser scanner unit on and off Method for main charger output 1 Select the main charger output on the screen for selecting an item: select one from MC ON, MC ON/OFF or LASER ON/OFF on the touch panel. The selected operation starts. 2 To stop operation, press the stop/clear key. Setting the grid control voltage 1 Press the MC DATA on the touch panel of the screen for selecting an item. 2 Change the setting using the Up/Down keys. Description Grid control voltage Setting range Initial setting 0 to 255 150
Description
Increasing the setting makes the surface potential higher, and decreasing it makes the potential lower. Change in value per step: approximately 3.6 V 3 Press the print key. The value is set. Interrupt copy mode While this maintenance item is being performed, copying from an original can be made in interrupt copy mode. Completion Press the stop/clear key at the screen for selecting an item when main charger output stops. The screen for selecting a maintenance item No. is displayed.
3-2-34
2AD Maintenance item No. U101 Setting high voltages Description Changes the developing bias voltage, transfer voltage and separation voltage by changing the developing bias control voltage, transfer control voltage and separation control voltage. Also checks the transfer output voltage. Purpose To check and change high voltages other than the main charger voltage. Start 1 Press the print key. The screen for selecting an item is displayed. 2 Select an item to be set or checked. The screen for the selected item is displayed. Display DEV BIAS SET TC SET AC SET Description Setting the developing bias Setting and checking the transfer voltage Setting the separation voltage
Description
Setting the developing bias 1 Select the item to be adjusted. The selected item is displayed in reverse, and the current setting is displayed in the adjustment window. 2 Change the setting using the Up/Down keys.
Display DB DATA
Operation Developing bias control voltage during image formation DB DATA2 Developing bias control voltage during no image formation
Increasing the setting makes the developing bias higher, and decreasing it makes the bias lower. 3 Press the print key. The value is set. 4 To return to the screen for selecting in item, press the stop/clear key.
3-2-35
Description Setting the transfer voltage 1 Change the setting using the Up/Down keys. Operation Transfer control voltage Setting range 0 to 255 Initial setting 140
Display TC DATA
Increasing the setting makes the transfer voltage higher, and decreasing it makes the voltage lower. 2 Press the print key. The value is set. 3 To check the transfer voltage output, press the TC ON on the touch panel. The currently set transfer voltage is output. 4 To stop the transfer voltage output, press the stop/clear key. 5 To return to the screen for selecting an item, press the stop/clear key after the transfer voltage output is stopped. Setting the separation voltage 1 Change the setting using the Up/Down keys. Display AC DATA Description Separation control voltage Setting range 0 to 255 Initial setting 100
Increasing the setting makes the separation voltage higher, and decreasing it makes the voltage lower. 2 Press the print key. The value is set. 3 To return to the screen for selecting an item, press the stop/clear key. Interrupt copy mode While this maintenance item is being performed, copying from an original can be made in interrupt copy mode. Completion Press the stop/clear key. The screen for selecting a maintenance item No. is displayed.
3-2-36
Description Setting the cleaning interval for the transfer charger Description Executes a cleaning operation for the transfer charger and changes the intervals at which the transfer charger is cleaned. Purpose To check the cleaning operation for the transfer charger. Also to change the intervals for the operation. Making the intervals longer decreases the stand-by time when starting copying. Method 1 Press the print key. The screen for selecting an item is displayed. 2 To execute the cleaning operation, press TEST RUN. The cleaning operation for the transfer charger is executed once. Setting 1 Change the setting using the Up/Down keys.
Description Setting range Initial setting Change in value per step Transfer charger 0 to 20 1 1000 copies cleaning operation intervals When set to 3, the transfer charger is cleaned every 3000 copies (3 by 1000) counted after the main switch is turned on. When set to 0, the transfer charger is not cleaned. 2 Press the print key. The value is set. Completion Press the stop/clear key. The screen for selecting a maintenance item No. is displayed.
3-2-37
Description Checking/clearing the drum count Description Displays the drum counts for checking or clearing the figure, which is used as a reference when correcting the main charger potential output. Purpose To check the drum status. Also used to clear the count after replacing the drum during regular maintenance. Since the count was cleared before shipping, do not clear it when installing. Method Press the print key. The drum counter count is displayed. Clearing 1 Press CLEAR on the touch panel. 2 Press the print key. The count is cleared, and the screen for selecting a maintenance item No. is displayed. Setting 1 Enter a six-digit count using the numeric keys. 2 Press the print key. The count is set, and the screen for selecting a maintenance No. is displayed. Completion To exit the maintenance mode without changing the count, press the stop/ clear key. The screen for selecting a maintenance item No. is displayed.
3-2-38
Description Checking/clearing the drum drive time Description Displays the drum drive time for checking or clearing a figure, which is used as a reference when correcting the high voltage based on time. Purpose To check the drum status. Also used to clear the drive time after replacing the drum. Method Press the print key. The drum drive time is displayed in minutes. Clearing 1 Press CLEAR on the touch panel. 2 Press the print key. The time is cleared, and the screen for selecting a maintenance item No. is displayed. Setting 1 Enter a five-digit drive time (in minutes) using the numeric keys. 2 Press the print key. The time is set, and the screen for selecting a maintenance No. is displayed. Completion To exit this maintenance item without changing the time, press the stop/ clear key. The screen for selecting a maintenance item No. is displayed.
3-2-39
Description Initial setting for the developer Description Automatically sets the toner sensor control voltage and toner feed start level for the installed developer. Purpose To set the initial settings for the developer when installing the machine or replacing the developer. Method 1 Press the print key. The screen for executing is displayed. 2 Press the print key. The initial settings for the developer is set, and the result is displayed. Display Description CONTROL Toner sensor control voltage TARGET Toner feed start level HUMID Absolute humidity The toner sensor output value is displayed on the right side of the screen. Supplement The following data is also renewed or cleared by performing this maintenance item: Renewing the toner sensor control voltage (U131) Renewing the toner feed start level (U156) Clearing the developing drive time (U157) Clearing the developing count (U158) Resetting the toner feed start level and toner empty detection Completion After initial setting is complete, press the stop/clear key. The screen for selecting a maintenance item No. is displayed.
3-2-40
Description Setting the toner sensor control voltage Description Displays or changes the toner sensor control voltage automatically set in maintenance item U130. Purpose To check the automatically set toner sensor control voltage. Also to change the toner density if an image is too dark or light. Method Press the print key. The current setting for the toner sensor control voltage is displayed. Setting 1 Change the setting using the Up/Down keys. Description Toner sensor control voltage Setting range 0 to 255 Initial setting 153
Increasing the setting makes the density higher, and decreasing it makes the density lower. Increasing the setting too high may result in toner scattering. 2 Press the print key. The value is set. Completion Press the stop/clear key. The screen for selecting a maintenance item is displayed.
3-2-41
2AD Maintenance item No. U132 Replenishing toner forcibly Description Replenishes toner forcibly until the toner sensor output value reaches the toner feed start level. Purpose Used when the toner empty is detected frequently. Method 1 Press the print key. The screen for executing is displayed. 2 Press the print key. Operation starts, and the current data is displayed. Toner is replenished until the toner sensor output value reaches the toner feed start level. To stop operation, press the start/clear key. Display TARGET (NOW) CONTROL (NOW) HUMID Description Current toner feed start level Current toner sensor control voltage Absolute humidity
Description
The current toner sensor output value is displayed on the right side of the screen. Completion Press the stop/clear key when toner replenishment stops. The screen for selecting a maintenance item No. is displayed. U133 Collecting the recycled toner Description Transfers residual toner in the cleaning section, toner main hopper and toner sub hopper to the developing unit. Purpose To dispose of residual toner inside the machine when the developer is replaced. Be sure to run this maintenance item before replacing the developer. Failing to do so could lead to toner scattering. There is no need to run this maintenance item if the developer is to be loaded for the first time in such occasion as machine installation.
3-2-42
Description Method 1 Press the print key. The screen for executing is displayed. 2 Press ON on the touch panel. The selected item is displayed in reverse. 3 Press the print key. The toner recycle motor turn on and recycled toner collection is performed for approximately 5 minutes. The ON display on the touch panel flashes during the operation and returns to the normal state when it ends. To interrupt operation, press the stop/clear key. Completion Press the stop/clear key when operation stops. The screen for selecting a maintenance item No. is displayed.
U135
Checking toner motor operation Description Drives the toner feed motor or toner recycle motor. Purpose To check the operation of the toner feed motor or toner recycle motor. Caution Note that driving either of the motors unnecessarily long may cause a toner jam, resulting in machine lockup. Be sure to drive each motor for just several seconds. Method 1 Press the print key. The screen for selecting an item is displayed. 2 Select the motor to be driven. The selected motor is displayed in reverse, and operation starts. Description MOTOR 1 MOTOR 2 Operation Toner feed motor drive Toner recycle motor drive
3 To stop operation, press the stop clear key. Completion Press the stop/clear key when operation stops. The screen for selecting a maintenance item No. is displayed.
3-2-43
Description Turning the toner level detection function on/off Description Turning the control based on the toner level sensor output on/off. Purpose To enable copying using the toner in the developing section after the toner level in the toner hopper decreases, by turning the control function off Method Press the print key. Setting 1 Press ON or OFF to change the operation. Display Description ON Controls based on the detection by the toner sensor detection sensor. OFF Ignores the detection by the toner level detection sensor. Initial setting: ON 2 Press the print key. The setting is set , and the screen for entering a maintenance item is displayed. Completion To exit this maintenance item without changing the current setting, press the stop/clear key. The screen for selecting a maintenance item No. is displayed.
U137
Checking the toner level detection sensor Description Displays the detection status of the toner level detection sensor and toner hopper lockup detection sensor. Purpose To check the toner level and recycle toner level in the toner hopper. Method 1 Press the print key. The detected status of the each sensor is displayed. Display Description TE1 SW Toner level detection sensor (toner level in the toner hopper) TE2 SW Toner hopper lockup detection sensor (recycle toner level) When there is toner or if the sensor connector is disconnected, on is detected , and the corresponding display is displayed in reverse. Completion Press the stop clear key. The screen for selecting a maintenance item No. is displayed.
3-2-44
Description Displaying the toner sensor output Description Displays the toner sensor output value , and related data. Purpose To check the toner sensor output value. Method 1 Press the print key. The screen for executing is displayed. 2 Press the print key. The current data is displayed. Display TARGET (NOW) Description Current toner feed level (corrected value for humidity and drive time) CONTROL (NOW) Current toner sensor control voltage HUMID Absolute humidity The current toner sensor output value is displayed on the right side of the screen. Completion Press the stop/clear key. The screen for selecting a maintenance item No. is displayed.
3-2-45
Description Changing the toner control level Description Changes the toner feed start level set in maintenance item U130 or the toner empty level to be determined by the difference from the toner feed start level. Purpose To check the toner feed start level and toner empty level. Method Press the start key. The screen for selecting an item is displayed.
Display Description TARGET Toner feed start level EMPTY Difference between the toner feed start level and toner empty level Setting for the toner feed start level 1 Press TARGET. 2 Change the setting using the Up/Down key. Description Toner feed start level Setting range 0 to 255 Initial setting 114
Increasing the setting makes the toner density lower. 3 Press the print key. The value is set. Setting for the toner empty level 1 Press EMPTY. 2 Change the setting using the Up/Down key. Description Difference between the toner feed start level and the toner empty level Setting range 0 to 255 Initial setting 20
Increasing the setting makes the toner empty level higher: the toner density is lower when the toner empty is detected. 3 Press the print key. The value is set. Completion Press the stop/clear key. The screen for selecting maintenance item No. is displayed.
3-2-46
Description Checking/clearing the developing drive time Description Checks or clears the developing drive time, which is used as a reference when correcting the toner control. It is automatically cleared when U130 is executed. Purpose To check the developing drive time after replacing the developer. Method Press the print key. The developing drive time is displayed in minutes. Clearing 1 Press CLEAR on the touch panel. 2 Press the print key. The count is set, and the screen for selecting a maintenance item No. is displayed. Setting 1 Enter a five-digit drive time (in minutes) using the numeric keys. 2 Press the print key. The time is set, and the screen for selecting a maintenance No. is displayed. Completion To exit the maintenance mode without changing the time, press the stop/ clear key. The screen for selecting a maintenance item No. is displayed.
U158
Checking/clearing the developing count Description Checks or clears the developing count, which is used as a reference when correcting the toner control. It is automatically cleared when U130 is executed. Purpose To check the developing count after replacing the developer. Method Press the print key. The developing count is displayed. Clearing 1 Press CLEAR on the touch panel. 2 Press the print key. The count is set, and the screen for selecting a maintenance item No. is displayed. Setting 1 Enter a six-digit count using the numeric keys. 2 Press the print key. The count is set, and the screen for selecting a maintenance No. is displayed. Completion To exit the maintenance mode without changing the count, press the stop/ clear key. The screen for selecting a maintenance item No. is displayed.
3-2-47
Description Applying toner to the cleaning blade Description Applies toner to the cleaning blade. Purpose To apply toner to the drum to coat the cleaning blade. To be executed when replacing or cleaning the cleaning blade or the drum. Method 1 Press the print key. The screen for executing is displayed. 2 Press the print key. Operation starts. When the operation is complete, the screen for selecting a maintenance item No. is displayed. Completion To exit this maintenance item without performing operation, press the stop/ clear key. The screen for selecting a maintenance item No. is displayed.
3-2-48
Description Setting the fixing control temperature Description Changes the fixing control temperature. Purpose Normally no change is necessary. However, can be used to prevent curled or creased paper, or solve a fixing problem on thick paper. Also used to output a test pattern for measuring fixing pressure. Method Press the print key. The screen for selecting an item is displayed. Setting 1 Select the item to be set. The selected item is displayed in reverse, and the current setting is displayed in the adjustment window. 2 Change the setting using the Up/Down key.
Display Description CONTROL TEMP Normal stabilization fixing temperature FIRST TEMP Primary stabilization fixing temperature SECOND TEMP Secondary stabilization fixing temperature RUNNING TIME Aging time after secondary stabilization
Setting range 100 to 200 (C) 100 to 200 (C) 100 to 200 (C) 0 to 120 (s)
The respective temperatures are to be set such that CONTROL TEMP $ SECOND $ TEMPFIRST TEMP. 3 Press the print key. The value is set. Interrupt copy mode While this maintenance item is being performed, a test pattern for measuring fixing pressure is output in interrupt copy mode (see page 3-378). Completion Press the stop/clear key. The screen for selecting maintenance item No. is displayed.
3-2-49
2AD Maintenance item No. U162 Stabilizing fixing forcibly Description Stops the stabilization fixing drive forcibly, regardless of fixing temperature. Purpose To forcibly stabilize the machine before the fixing section reaches stabilization temperature. Method 1 Press the print key. The screen for executing is displayed. 2 Press the print key. The forced stabilization mode is entered, and stabilization operation stops. The screen for selecting a maintenance item No. is displayed. To exit the forced stabilization mode, turn the power off and on. Completion To exit this maintenance item without executing forced fixing stabilization, press the stop clear key. U196 Turning the fixing heater on Description Turns the fixing heater on. Purpose To check fixing heaters M or S. Method 1 Press the print key. The screen for selecting an item is displayed. 2 Select the heater to be turned on. The selected heater turns on for 3 s and then turns off. Display MAIN SUB Description Fixing heater M (H1) Fixing heater S (H2)
Description
Completion Press the stop/clear key when fixing motors M and S are off. The screen for selecting the maintenance item No. is displayed.
3-2-50
Description Setting the fixing phase control Description Sets the use of fixing phase control to reduce electrical noise generated by the copier. Purpose Normally no change is necessary. If electrical noise generated by the copier causes flickering of the lights around the copier, select fixing phase control to reduces the noise. Method Press the print key. Setting 1 Press ON or OFF to change operation. Display Description ON Fixing phase control present OFF Fixing phase control absent Initial setting: ON for metric and OFF for inch specifications 2 Press the print key. The setting is set. The screen for selecting a maintenance item No. is displayed. Completion To exit this maintenance item without changing the current setting, press the stop/clear key. The screen for selecting a maintenance item No. is displayed.
U200
Turning all LEDs on Description Turns all the LEDs on the operation panel on. Purpose To check if all the LEDs on the operation panel light Method Press the print key. All the LEDs on the operation panel light. Completion Press the stop/clear key or wait for 10 s. The LEDs turns off, and the screen for selecting a maintenance mode is displayed.
3-2-51
2AD Maintenance item No. U201 Initializing the touch panel Description Automatically correct the positions of the X- and Y-axes of the touch panel. Purpose To automatically correct the display positions on the touch panel after it is replaced. Method 1 Press the print key. The screen for executing is displayed, and the + key displayed at the upper left of the touch panel flashes. 2 Press on the center of the + key. The + key on lower right flashes. 3 Press the center of the flashing +. Initialization of the touch panel is complete, and the screen for selecting a maintenance item No. is displayed. Completion To exit this maintenance item without initializing, press the stop/clear key. The screen for selecting a maintenance mode No. is displayed.
Description
3-2-52
Description Setting the MMD host monitoring system Description Initializes or operates the MMD host monitoring system* * Optional for 120 V specifications only. Purpose Used when setting up the machine or during regular maintenance or repair. Method 1 Press the print key. The basic status screen is displayed. 2 Operates the device following the instructions on the touch panel. Completion Press the stop/clear key on the basic screen. The screen for selecting a maintenance item No. is displayed. [Basic status]
Maintenance item No. select screen Technician arrive Maintenance count clear
U202
1 2 3 4 5
To initialize the MMD host monitoring system, run the following modes in order: Phone number setting 4 Device initialization 5 During regular maintenance or service Technician arrive 1 Maintenance count clear 2 Service report (leave) 3
3-2-53
Description 2
Maintenance parts check/clear Select parts & push clear DRUM DEVELOPER 00000000 00000000 00000000 00000000 00000000
U202
Ready to send Push print key Print key Transmission start Basic status screen
Clear
Maintenance parts check/clear Select parts & push clear SEP.CLAW MOUNT00000000 SEP.CLAW ASS'Y 00000000 HEAT ROLLER PRESS ROLLER FIX HEATER M 00000000 00000000 00000000
U202
Clear
Clear Stop/ clear key Ready to send Push print key Print key Counts are cleared. Basic status screen
3-2-54
Description
U202
Select an item. Ready to send Push print key Print key Transmission starts.
U202
0000000000 0000000000 0000000000 Pulse10 Pulse20
Select an item and enter the digits using numeric keys. Press the interrupt key to enter a space.
Set
Set Ready to send Push print key Stop/ clear key Print key The phone number is stored. Basic status screen
3-2-55
Description 5
Device initialization Select a mode
U202
Standard
Standard
U202
000000
U202
000000
Enter the digits using the numeric keys and press the print key.
Device initialization Select a mode PPC ID Initialization ID
Enter the digits using the numeric keys and press the print key.
Device initialization Select a mode Model Personal ID
U202
000000 000000
U202
000000 000000
Enter the digits using the numeric keys and press the print key.
Device initialization Select a mode PPC ID Initialization ID Total count
Enter the digits using the numeric keys and press the print key.
Device initialization Select a mode Model Personal ID Total count
U202
000000 000000 00000000
U202
000000 000000 00000000
Enter the digits using the numeric keys and press the print key.
Enter the digits using the numeric keys and press the print key.
51
3-2-56
Description
Ready to send Push print key Print key Initialization starts. Yes Initialization succeeded? Yes No
xxxx (Reason for failure) Check Check MMD system problem? No Screen depending on the reason for failure
U202
Retry initialization 51
3-2-57
2AD Maintenance item No. U203 Operating DF separately Description Simulates the original conveying operation separately in the SRDF. Purpose To check the SRDF. Method 1 Press the print key. The screen for selecting an item is displayed. 2 Set the magnification to between 25 and 200% using the Up/Down keys. 3 Place an original in the SRDF if running this simulation with paper. 4 Select the item to be operated. The selected item is displayed in reverse and operation starts. Display Operation ADF MODE With paper, single-sided original RADF MODE With paper, double-sided original ADF MODE (NON-PAPER) Without paper, single-sided original (continuous operation) RADF MODE (NON-PAPER) Without paper, double-sided original (continuous operation) 5 To stop continuous operation, press the stop/clear key. Completion Press the stop/clear key when the operation stops. The screen for selecting the maintenance item No. is displayed.
Description
3-2-58
Description Setting the presence or absence of a key card or key counter Description Sets the presence or absence of the optional key card or key counter. Purpose A key card is not available for metric specifications. The setting for the HECON key card, which is supported by inch-specification machines, is not necessary in this maintenance item. Method Press the start key. Setting 1 Select the optional counter to be installed. The selected counter is displayed in reverse. Pressing the reversed item again resets the selection. Display Description KEY CARD The key card is installed. KEY COUNTER The key counter is installed. 2 Press the print key. The screen for selecting a maintenance item No. is displayed. Completion To exit this maintenance item without changing the current setting, press the stop/clear key. The screen for selecting a maintenance item No. is displayed.
3-2-59
Description Setting the presence or absence of the coin vender Description Sets the presence or absence of the optional coin vender. Also sets the details for coin vender operation, such as mode and unit price. This is an optional device which is currently supported only by Japanese specification machines, so no setting is necessary.
3-2-60
2AD-1 2AD Maintenance item No. U209 Setting date and time Description Sets the real time clock, which is used as a reference when correcting drum time. Purpose To set the date and time after initializing data. Method 1 Press the print key. The screen for executing is displayed. The current setting for the year is displayed. 2 Set the year (last two digits of the year) using the numeric or Up/Down keys and press the print key. The current setting for the month is displayed. 3 Set the month using the numeric or Up/Down keys and press the print key. The current setting for the date is displayed. 4 Set the date using the numeric or Up/Down keys and press the print key. The current setting for the day of the week is displayed. 5 Set the day of the week using the numeric or Up/Down keys and press the print key. The current time setting for hours is displayed. Setting 1 2 3 4 5 6 7 Description Monday Tuesday Wednesday Thursday Friday Saturday Sunday
Description
6 Set the time (hours, 0 to 23) using the numeric or Up/Down keys and press the print key. The current time setting for minutes is displayed. 7 Set the minutes using the numeric or Up/Down keys and press the print key. Setting is complete, and the screen for selecting a maintenance item No. is displayed. Supplement To return to the last screen, press the stop/clear key while setting. Completion To stop this maintenance item without changing the current setting, press the stop/clear key at the screen for the year setting. The screen for selecting a maintenance item No. is displayed.
3-2-61
Description Checking the operation of the DF motors, clutches and solenoids Description Turns the SRDF motors, clutches or solenoids on. Purpose To check the operation of the SRDF motors, clutches and solenoids. Method 1 Press the print key. The screen for selecting an item is displayed. 2 Select the item to be operated. The selected item is displayed in reverse, and operation starts.
Motors, clutches and solenoids Original feed motor (OFM) Original paper conveying motor (OCM) Original feed clutch (OFCL) Eject feedshift solenoid (EFSSOL) Switchback feedshift solenoid (SBFSSOL) Original feed solenoid (OFSOL) Switchback pressure solenoid (SBPSOL)
Operation In operation In operation On for 0.5 s On for 0.5 s On for 0.5 s On and off On and off
3 To turn each motor off, press the stop/clear key. Completion Press the stop/clear key when operation stops. The screen for selecting a maintenance item No. is displayed.
3-2-62
2AD Maintenance item No. U244 Checking the DF switches Description Displays the status of the respective switches on the SRDF. Purpose To check if respective switches on the SRDF operate correctly. Start 1 Press the print key. The screen for selecting an item is displayed. 2 Select the type of switches (SW or VR) to be checked. The screen for executing is displayed. Display Type of switches SW On/off switches VR Volume switch Method for the on/off switches 1 Turn the respective switches on and off manually to check the status. If the on-status of a switch is detected, the corresponding switch is displayed in reverse. Display Switches SET SW Original set switch (OSSW) FEED SW Original feed switch (OFSW) REV SW Original switchback switch (OSBSW) TMG SW DF timing switch (DFTSW) SZ A SW Original size length switch (OSLSW)
Description
2 To return to the screen for selecting an item, press the stop/clear key. Method for the volume switch 1 Move the original insertion guides to check the detection status of the original size width switch. As shown on the next page, the detected original width is displayed as a numerical value with the decimals omitted.
3-2-63
2AD Maintenance item No. U244 Numerical value 000 49.664 A5R 50.176 61.440 61.952 B5R 103.936 104.448 Folio/A4R 139.264 139.776 146.432 B4/B5 146.994 197.120 197.632 197.720 223.232 A3/A4 256 For example, if any value between 105 and 139 is displayed when the original insertion guides are adjusted for A4R paper, it indicates that the original width is detected correctly. 2 To return to the screen for selecting an item, press the stop/clear key. Completion Press the stop/clear key at the screen for selecting an item. The screen for selecting a maintenance item No. is displayed. CF (11" 15") 11" 17"/ 11" 15"/ 11" 81/2" 81/2" 14"/ 81/2" 11"
3-2-64
2AD Maintenance item No. U245 Checking messages Description Displays a list of messages on the touch panel of the operation panel. Purpose To check the messages to be displayed. Method 1 Press the print key. 2 Change the screen using the Up/Down keys to display each message one at a time. Completion Press the stop/clear key. The screen for selecting a maintenance item No. is displayed. U247 Checking the operation of the large paper deck and paper feed desk Description Turns on motors and clutches of the large paper deck or the upper and lower drawers of the optional paper feed desk. However, this machine currently does not support the use of the upper or lower drawer of the paper feed desk. Purpose To check the operation of motors and clutches of the respective paper feed devices. Start 1 Press the print key. The screen for selecting an item is displayed. 2 Select the paper feed device to be checked. The screen for executing is displayed. Display 3000 DECK 500 2 DESK Paper feed device Large paper deck Upper and lower drawers of the paper feed desk
Description
Method 1 Press the item to be operated. The selected item is displayed in reverse and operation starts. Large paper deck Display Motors and clutches LCF MOT Deck paper conveying motor (CM) L CL Paper feed clutch 1 (PFCL1) PCL1 Paper conveying clutch (CCL) PCL2 Paper feed clutch 2 (PFCL2) Operation On for 5 s On for 1s On for 1s On for 1s
3-2-65
2AD-1 2AD Maintenance item No. U247 Display DESK MOT FEED CL UPP CL LOW CL
Description Upper and lower drawers of the paper feed desk Motors and clutches Desk drive motor (DDM) Desk feed clutch (DFCL) Upper desk paper feed clutch (DPFCL-U) Lower desk paper feed clutch (DPFCL-L) Operation On for 5 s On for 1 s On for 1s On for 1s
2 To return to the screen for selecting an item, press the stop/clear key. Completion Press the stop/clear key at the screen for selecting an item. The screen for selecting a maintenance item No. is displayed. U248 Setting the paper eject device Description Adjusts the amount of slack in the paper for the optional finisher in punch mode when it is attached. Also sets the punch limit and displays and clears the punch-hole scrap count. Purpose Adjustment of the amount of slack in the paper in punch mode
Adjusts the amount of slack in the paper while in the punch section if, in punch mode, paper jams or is Z-folded frequently due to too much slack in the paper, or, the position of punch holes varies due to too little slack in the paper.
Punch limit setting Sets the punch limit to notify the user of the time to collect punch-hole scrap. Punch-hole scrap count display (clearing) Used to manually clear the punch-hole scrap count if a message requiring collection of punch-hole scrap is shown on the touch panel after collection. If punch-hole scrap is collected with the copier power turned off, the punch-hole scrap count is not cleared and consequently this problem occurs. Start Press the print key. The screen for selecting an item is displayed. Display PUNCH TIMING PUNCH LIMIT Description Adjustment of the amount of slack in the paper in punch mode Punch limit/punch-hole scrap count
3-2-66
2AD-1 2AD Maintenance item No. U248 Description Setting range Punch timing Amount of slack in the paper 15 to +15 Initial setting 0
Description
I f the position of punch holes varies, increase the setting to make the amount of slack larger. If paper jams or is Z-folded frequently, decrease the setting to make the amount of slack smaller. Changing the value by 1 changes the amount of slack by 1.25 mm.
3 Press the print key. The value is set. 4 To return to the screen for selecting an item, press the stop/clear key. Setting the punch limit or displaying the punch-hole scrap count 1 Select PUNCH LIMIT on the screen for selecting an item. 2 Select the item to be set. 3 Change the setting using the numeric keys or the Up/Down keys. To clear the punch-hole scrap count, press the all clear/reset key. Display Description PUNCH LIMIT Punch limit (maximum number of punching times) PUNCH CNT Punch-hole scrap count (current number of punching times) Setting range Initial setting 0 to 999000 75000 0 to 999999
PUNCH LIMIT can be changed in increments of 1000 times. When the punch-hole scrap count reaches the punch limit, Check punch waste tank. is displayed on the touch panel. 4 Press the print key. The value is set. 5 To return to the screen for selecting an item, press the stop/clear key. Completion Press the stop/clear key at the screen for selecting an item. The screen for selecting a maintenance item No. is displayed.
3-2-67
Description Setting the maintenance cycle Description Displays and changes the maintenance cycle. Purpose To check and change the maintenance cycle. Method Press the print key. The current setting is displayed as follows: Maintenance cycle (number of copies) = setting 1000 Setting 1 Change the setting using the Up/Down keys.
For example, when set to 120, the maintenance cycle is set to 120000. Pressing the Up key when set to 600 rolls over the setting to 0. 2 Press the start key. The value is set , and the screen for selecting a maintenance item No. is displayed. Completion To exit this maintenance item without changing the current setting, press the stop/clear key. The screen for selecting an item is displayed. U251 Checking/clearing the maintenance count Description Displays, clears and changes the maintenance count. Purpose To check the maintenance count. Also to clear the count during maintenance service. Method Press the print key. The maintenance count is displayed. Clearing 1 Press CLEAR on the touch panel. 2 Press the print key. The count is set, and the screen for selecting a maintenance item is displayed. Setting 1 Enter a six-digit count using the numeric key. 2 Press the print key. The count is set , and the screen for selecting a maintenance item is displayed. Completion To exit this maintenance item without changing the count, press the stop/ clear key. The screen for entering a maintenance item No. is displayed.
3-2-68
2AD Maintenance item No. U252 Setting the destination Description Switches the operations and screens of machines according to the respective destinations. Purpose To be executed after replacing the backup RAM on the main PCB or initializing the backup RAM by running maintenance item U020, in order to return the setting to the value before replacement or initialization. Method Press the print key. The screen for entering an item is displayed. Setting 1 Select the destination. The selected item is displayed in reverse. Display JAPAN METRIC INCH EUROPE METRIC ASIA PACIFIC Description Metric (Japan) specifications Inch specifications Metric (Europe) specifications Metric (Asia Pacific) specifications
Description
2 Press the print key. The value is set, and the screen for selecting a maintenance item No. is displayed. Completion To exit this maintenance item without changing the count, press the stop/ clear key. The screen for entering a maintenance item No. is displayed. Supplement The specified initial settings are provided according to the destinations in the maintenance items below. To change the initial settings in those items, be sure to run maintenance item U021 after changing the destination. Initial setting according to the destinations Maintenance Title item No. 198 Setting the fixing phase control 253 Switching between double and single counts 255 Setting auto clear time 347 348 Setting auto drawer size detection Setting copy density adjustment range Japan ON SINGLE COUNT 120 s ON NORMAL Inch OFF DOUBLE COUNT 90 s ON SPECIAL AREA Europe Metric, Asia Pacific ON DOUBLE COUNT 90 s OFF SPECIAL AREA
3-2-69
Description Switching between double and single counts Description Switches the count system for the total count and other counts. Purpose According to user (copy service provider) request, select if A3/11" x 17" paper is to be counted as one sheet (single count) or two sheets (double count). Method Press the print key. The screen for selecting an item is displayed. Setting 1 Select double or single count. Display Description DOUBLE COUNT Double count for A3/11" 17" paper only Single count for all size paper SINGLE COUNT Initial setting: DOUBLE COUNT 2 Press the print key. The value is set, and the screen for selecting an maintenance item No. is displayed. Completion To exit this maintenance item without changing the current setting, press the stop/clear key. The screen for selecting an maintenance item No. is displayed.
3-2-70
Description Turning auto start function on/off Description Selects if the auto start function is turned on. Purpose Normally no change is necessary. If incorrect operation occurs, turn the function off: this may solve the problem. Method Press the start key. The screen for entering an item is displayed. Setting 1 Select either ON or OFF. The selected item is displayed in reverse. Display Description ON Auto start function on OFF Auto start function off Initial setting: ON 2 Press the print key. The setting is set. The screen for selecting a maintenance item is displayed. Completion To exit this maintenance item without changing the current setting, press the stop clear key. The screen for selecting a maintenance item No. is displayed.
3-2-71
2AD Maintenance item No. U255 Setting auto clear time Description Sets the time to return to initial settings after copying is complete. Purpose To be set according to frequency of use. Set to a comparatively long time for continuous copying at the same settings, and a comparatively short time for frequent copying at various settings. Method Press the print key. The value is set. Current settings are displayed. Setting 1 Change the setting using the Up/Down key. Description Auto clear time Setting range 0 to 270 Initial setting 90
Description
The setting can be changed by 30 s per step. Pressing the Up key when set to 270 rolls over the setting to 0. When set to 0, the auto clear function is cancelled. 2 Press the print key. The value is set. The screen for selecting a maintenance item is displayed. Completion To exit this maintenance item without changing the current setting, press the stop clear key. The screen for selecting a maintenance item No. is displayed.
3-2-72
Description Turning auto preheat/energy saver function on/off Description Selects if the auto preheat/energy saver function is turned on. When set to ON, the time to enter preheat/energy saver mode can be changed in copy management mode. Purpose According to user request, to set the preheat time to save energy, or enable copying promptly without the recovery time from preheat mode. Method Press the print key. The setting is set. The screen for selecting an item is displayed. Setting 1 Select ON or OFF. The selected item is displayed in reverse. Display Description ON Auto preheat/energy saver function on OFF Auto preheat/energy saver function off Initial setting: ON 2 Press the print key. The setting is set. The screen for selecting a maintenance item is displayed. When change from OFF to ON, the initial value of 15 min. is set. Completion To exit this maintenance item without changing the current setting, press the stop clear key. The screen for selecting a maintenance item No. is displayed.
3-2-73
Description Switching copy operation at toner empty detection Description Selects if continuous copying is enabled after toner empty is detected, and sets the number of copies that can be made after the detection. Method Press the print key. The current setting is displayed. Setting 1 Select single or continuous copying. The selected item is displayed in reverse. Display Description SINGLE MODE Enables only single copying. CONTINUE MODE Enables single and continuous copying. Initial setting: SINGLE MODE 2 Set the number of copies that can be made using the Up/Down keys.
The setting can be changed by 5 copies per step. When set to 0, the number of copies is not limited regardless of the setting for single or continuous copying. 3 Press the print key. The setting is set , and the screen for entering a maintenance item No. is displayed. Completion To exit this maintenance item without changing the current setting, press the stop/clear key. The screen for selecting a maintenance item is displayed.
3-2-74
Description Changing the copy count timing Description Changes the copy count timing for the total counter and other counters. Purpose To be set according to user (copy service provider) request. If a paper jam occurs frequently in the finisher when the number of copies is counted at the time of paper ejection, copies are provided without copy counts. The copy service provider cannot charge for such copying. To prevent this, the copy timing should be made earlier. If a paper jam occurs frequently in the paper conveying or fixing sections when the number of copies is counted before the paper reaches those sections, copying is charged without a copy being made. To prevent this, the copy timing should be made later. Method Press the start key. The screen for selecting an item is displayed. Setting 1 Select the copy count timing. Display Description COUNT:FEED When secondary paper feed starts. COUNT:EJEC When the paper is ejected. Initial setting: EJECT 2 Press the print key. The setting is set , and the screen for entering a maintenance item No. is displayed. Completion To exit this maintenance item without changing the current setting, press the stop/clear key. The screen for selecting a maintenance item is displayed.
3-2-75
Description Switching between duplex/simplex copy mode Description Switches the initial setting between duplex and simplex copy. Purpose To be set according to frequency of use: set to the more frequently used mode. Method Press the start key. The screen for selecting an item is displayed. Setting 1 Select ON or OFF. Display Description ON Duplex copy OFF Simplex copy Initial setting: OFF 2 Press the print key. The setting is set, and the screen for entering a maintenance item No. is displayed. Completion To exit this maintenance item without changing the current setting, press the stop/clear key. The screen for selecting a maintenance item is displayed.
3-2-76
Description Setting preheat/energy saver mode Description Changes the control mode for preheat/energy saver. Purpose According to user request, selects which has priority, the recovery time from preheat or energy saver. Method Press the start key. The screen for selecting an item is displayed. Setting 1 Select control mode.
Control in preheat mode Without decreasing the fixing control temperature, the display on the operation panel is turned off. ENERGY STAR The fixing control temperature is decreased by 10C/18F, the copier is forcibly stabilized 30 s after exiting preheat mode. E 2000 The fixing control temperature is decreased by 20C/36F. Initial setting: Energy Star applied 3 Press the print key. The setting is set, and the screen for entering a maintenance item No. is displayed. Completion To exit this maintenance item without changing the current setting, press the stop/clear key. The screen for selecting a maintenance item is displayed.
3-2-77
Description Setting the value for maintenance due indication Description Sets when to display a message notifying that the time for maintenance is about to be reached, by setting the number of copies that can be made before the current maintenance cycle ends. When the difference between the number of copies of the maintenance cycle and that of the maintenance count reaches the set value, the message is displayed. Purpose To change the time to display the maintenance due indication. Method Press the print key. The current setting is displayed.
Setting 1 Change the setting using the numeric or Up/Down keys. Description Setting range Display period for the next maintenance 0 to 9999 (remaining count before the end of the maintenance cycle) Initial setting: 0 2 Press the print key. The setting is set, and the screen for entering a maintenance item No. is displayed. Completion To exit this maintenance item without changing the current setting, press the stop/clear key. The screen for selecting a maintenance item is displayed.
3-2-78
Description Setting auto drawer size detection Description Turning the auto drawer size detection function on/off. Purpose To be used when turning the auto paper size (in the drawers) detection off and making copies onto only the specified size paper. Method Press the print key. The screen for selecting an item is displayed. Setting 1 Select ON or OFF. Display Description ON Detects the paper sizes in the drawers automatically. OFF Does not detect the paper sizes in the drawers automatically. Initial setting: ON for inch and OFF for metric specifications 2 Press the print key. The setting is set, and the screen for entering a maintenance item No. is displayed. Completion To exit this maintenance item without changing the current setting, press the stop/clear key. The screen for selecting a maintenance item is displayed.
3-2-79
Description Setting the copy density adjustment range Description Selects the adjustment range for copy density from NORMAL and SPECIAL AREA (for wider range). Purpose To change the setting according to user request. When especially dark or light density is requested, set to SPECIAL AREA. Method Press the print key. The screen for selecting an item is displayed. Setting 1 Select the density range. Display Description SPECIAL AREA 25 steps (enlargement mode) NORMAL 13 steps Initial setting: SPECIAL AREA 2 Press the print key. The setting is set, and the screen for entering a maintenance item No. is displayed. Completion To exit this maintenance item without changing the current setting, press the stop/clear key. The screen for selecting a maintenance item is displayed.
U402
U403
Adjusting margins for reading an original on the contact glass Adjustment See page 3-3-38.
U404
3-2-80
Description Checking/clearing copy counts by paper feed locations Description Displays or clears copy counts by paper feed locations. Purpose To check the time to replace consumable parts. Also to clear the counts after replacing the consumable parts. Method 1 Press the print key. The counts by paper feed locations are displayed. 2 Change the screen using the Up/Down keys. Display BYPASS FIRST SECOND THIRD* FORTH* LCF DUPLEX Paper feed locations Bypass table Copier upper drawer Copier lower drawer Paper feed desk upper drawer Paper feed desk lower drawer Large paper deck Duplex unit
* Optional. However, currently not supported by this machine. When an optional paper feed device is not installed, the corresponding count is not displayed. Clearing 1 Select the count to be cleared. The selected item is displayed in reverse. To clear the counts for all paper feed locations, press ALL on the touch panel. 2 Press the print key. The setting is set, and the screen for entering a maintenance item No. is displayed. Completion To exit this maintenance item without changing the current setting, press the stop/clear key. The screen for selecting a maintenance item is displayed.
3-2-81
Description Checking/clearing the paper jam counts Description Displays or clears the jam counts by jam locations. Purpose To check the paper jam status. Also to clear the jam counts after replacing consumable parts. Method 1 Press the print key. The jam count is displayed by jam codes. 2 Change the screen using the Up/Down keys. Clearing 1 Press ALL on the touch panel. Jam counts cannot be cleared individually. 2 Press the print key. The count is cleared, and the screen for entering a maintenance item No. is displayed. Completion To exit this maintenance item without changing the current setting, press the stop/clear key. The screen for selecting a maintenance item is displayed.
3-2-82
Description Checking/clearing the service call counts Description Displays or clears the service call code counts by types. Purpose To check the service call code status by types. Also to clear the service call code counts after replacing consumable parts. Method 1 Press the print key. The jam count is displayed by service call codes. 2 Change the screen using the Up/Down keys. Clearing 1 Select the count to be cleared. The selected count is displayed in reverse. To clear all counts, press ALL on the touch panel. 2 Press the print key. The count is cleared. When all counts are cleared, the screen for entering a maintenance item No. is displayed. Completion Press the stop/clear key. The screen for selecting a maintenance item is displayed.
3-2-83
Description Checking/clearing counts by optional devices Description Displays or clears the counts by optional devices. Purpose To check the use of the SRDF and finisher. Also to clear the counts after replacing consumable parts. Method 1 Press the print key. The screen for selecting an item is displayed. 2 Select the device, the count of which is to be checked. The count of the selected device is displayed. SRDF (DF) Display Description CHANGE Original replacement count ADF No. of single-sided originals that has passed through the DF in ADF mode RADF No. of double-side originals that has passed through the DF in RADF mode Finisher (SORTER)
Description No. of copies that has passed Frequency the stapler has been activated Frequency the punch has been activated Frequency the stacker has been activated
Clearing 1 Select the item to be cleared. The selected item is displayed in reverse. 2 Press the print key. The count is cleared. 3 To return to the screen for entering an item, press the stop/clear key. Completion Press the stop/clear key at the screen for selecting an item. The screen for selecting a maintenance item is displayed.
3-2-84
Description Resetting partial operation control Description Resets the service call code for partial operation control. Purpose To be reset after partial operation is performed due to problems in the drawers or other sections below, and the related parts are serviced. The following sections can be the subject of the partial operation: SRDF Large paper deck Copier upper drawer Copier lower drawer Paper feed desk upper drawer Paper feed desk lower drawer Duplex unit Finisher Scanner Method 1 Press the print key. 2 Press RESET on the touch panel. 3 Press the print key to reset partial operation control. The maintenance mode is exited, and the machine returns to the same status when the main switch is turned on.
3-2-85
Description Checking/clearing the time for the exposure lamp to light Description Displays, clears or changes the accumulated time for the exposure lamp to light. Purpose To check duration of use of the exposure lamp. Also to clear the accumulated time for the lamp after replacement. Method Press the print key. The accumulated time of illumination for the exposure lamp is displayed in minutes. Clearing 1 Press CLEAR on the touch panel. 2 Press the print key. The accumulated time is cleared, and the screen for selecting a maintenance item No. is displayed. Setting 1 Enter a six-digit accumulated time using the numeric keys. 2 Press the print key. The time is set, and the screen for selecting a maintenance item is displayed. Completion To exit this maintenance item without changing the accumulated time, press the stop/clear key. The screen for selecting a maintenance item is displayed.
3-2-86
Description Checking/clearing the printer count Description Displays, clears or changes the print count of the printer when the optional printer unit is installed. Purpose To check the frequency of use of the printer. Method Press the print key. The printer count is displayed. Clearing 1 Press CLEAR on the touch panel. 2 Press the print key. The count is set, and the screen for selecting a maintenance item is displayed. Setting 1 Enter a six-digit numerical value using the numeric keys. 2 Press the print key. The count is set, and the screen for selecting a maintenance item is displayed. Completion To exit this maintenance item without changing the count, press the stop/ clear key. The screen for selecting a maintenance item is displayed.
3-2-87
2AD-1 2AD
Default/Special: on
Management: on
Enter an ID code
Enter an ID code
End: on
Copy default: on
Enter an ID code
Machine default: on
Enter an ID code
Language: on
End
3-2-88
Registering a new department code Sets a department code and the limit of the number of copies for that department. 1. SET CODE: on 2. REGISTER: on 3. Enter a department code using the numeric keys: 7 digits for inch specifications and 4 digits for metric specifications. 4. REGISTER: on 5. Enter the limit using the numeric keys. Setting range is 1000 to 999000 (in every 1000) copies. Set to 0 for unlimited copies. 6. REGISTER: on 7. END: on 8. END: on
Altering the copy limit 1. SET CODE: on 2. CORRECTION: on 3. Select the department code to be altered. 4. Enter the limit of the number of copies using the numeric keys. 5. REGISTER: on 6. END: on 7. END: on
Viewing copy counts Deleting a department code 1. SET CODE: on 2. DELETE: on 3. Select the department code to be deleted. 4. END: on 5. END: on 1. REFERENCE: on 2. END: on
Printing a copy management report 1. Set A4/8 1/2" x 11" copy paper. 2. PRINT MANAGEMENT LIST: on
3-2-89
Setting the time 1. TIMER SET: on 2. Set the current day of the week, hour and minute by pressing +/symbols (24-hour clock format). 3. ENTER: on
Programming the week timer Set the on/off time for each day of the week. 1. WEEK TIMER: on 2. Select the day of the week to be set. 3. Select ON and set hours and minutes by pressing the +/symbols. 4. Select OFF and set hours and minutes by pressing the +/symbols. 5. ENTER: on 6. ENTER: on
Canceling the timer function 1. CANCEL: on 2. Select the day of week to be canceled. 3. ENTER: on
3-2-90
Exposure mode Selects auto or manual exposure to be given priority in initial mode. 1. Display EXPOSURE MODE using the Up/Down keys. 2. Select AUTO or MANUAL.
Copy quality Sets the image quality to be selected in initial mode. 1. Display COPY QUALITY using the Up/Down keys. 2. Select MIXED, TEXT or PHOTO.
Exposure steps Sets the exposure steps in manual exposure mode. 1. Display EXPOSURE STEPS using the Up/Down keys. 2. Select 7 STEPS or 13 STEPS.
Paper selection Set if the same sized paper as the original to be copied is automatically selected. 1. Display PAPER SELECTION using the Up/Down keys. 2. Select AUTO or MANUAL.
Auto exposure adjustment Job programming Adjusts the exposure in auto density mode. 1. Display AUTO EXPOSURE ADJUSTMENT using the Up/Down keys. 2. CHANGE: on 3. Adjust the exposure by pressing DARKER or LIGHTER. 4. END: on Selects whether all program numbers are selectable or program No. 1 is given priority. 1. Display JOB PROGRAMMING using the Up/Down keys. 2. Select REGULAR (for all program numbers) or OFF THE PLATEN (for program No. 1).
Manual exposure adjustment. Adjusts the exposure in manual density mode. 1. Display MANUAL EXPOSURE ADJUSTMENT using the Up/ Down keys. 2. CHANAGE: on 3. Adjust the exposure by pressing DARKER or LIGHTER. Setting is available for text, text and photo (mixed) and photo modes. 4. END: on
Default drawer Set the drawer to be selected after the all clear/reset key is pressed. 1. Display DEFAULT DRAWER using the Up/Down keys. 2. CHANGE: on. 3. Select the default drawer.
3-2-91
2AD
Zoom mode Selects fixed or standard magnifications in reduction/enlargement mode. 1. Display ZOOM MODE using the Up/Down keys. 2. Select SIZE ZOOM or STANDARD ZOOM.
Custom size for border erase Sets the custom size for border erase copying. 1. Display CUSTOM SIZE FOR BORDER ERASE using the Up/Down keys. 2. CHANGE: on 3. Set the paper width by pressing the upper +/- symbols. Setting is available between 94 mm/311/ 16" and 214mm/87/ 16" in 8 mm/5/ 16" steps. 4. Set the paper length by pressing the lower +/- symbols. Setting is available between 60 mm/23/8" and 296 mm/11 5/ 8" in 4 mm/2/16 ". 5. END: on
Copy limit Sets the limit of the number of copies for multiple copying. 1. Display COPY LIMIT using the Up/Down keys. 2. CHANGE: on 3. Enter the number of copies up to 999 using the numeric keys. 4. CHANGE: on
Front and back page margin Sets if individual margin settings for front and back page are available. 1. Display F & BP. MARGIN using the Up/Down keys. 2. Select ON or OFF.
Drawer for insert sheet 1. Display DRAWER FOR INSERT SHEET using the Up/Down keys. 2. CHANGE: on 3. Select the paper feed location.
Rotate sort Sets if rotate sort is available in sort copy mode. Setting is not available when the finisher is installed. 1. Display ROTATE SORT using the Up/Down keys. 2. Select ON or OFF.
3-2-92
2AD
Create shortcut Registers frequently used function keys, and displays them on the basic screen. 1. Display CREATE SHORTCUT #1 or CREATE SHORTCUT #2 using the Up/Down keys. 2. CHANGE: on 3. Select a function.
Create user choice #1-#5 Moves frequently used function keys to the basic screen for selecting a function. 1. Display one of CREATE USER CHOICE/Customize GUI #1 to #5 using the Up/Down keys. 2. CHANGE: ON 3. Select the function to be moved.
3-2-93
Un-fixed size from bypass Sets if non-standard size paper is available when the paper is fed from the bypass table. 1. Display UN-FIXED SIZE FROM BYPASS using the Up/Down keys. 2. Select ON or OFF.
APS for special paper Sets if auto paper selection is available for the paper feed location with the special paper. 1. Display APS FOR SPECIAL PAPER using the Up/Down keys. 2. Select ON or OFF.
Auto drawer switching Sets if the auto drawer switching function is available. 1. Display AUTOMATIC DRAWER SWITCHING using the Up/Down keys. 2. Select ON or OFF.
Key sound Sets if a beep sounds when a key on the key touch panel is pressed. 1. Display KEY SOUND using the Up/Down keys. 2. Select ON or OFF.
Auto preheat time Drawer paper size Changes the paper size for the drawers displayed on the basic screen. 1. Display DRAWER PAPER SIZE for the drawer to be changed using the Up/Down keys. 2. CHANGE: ON 3. Select paper size. Sets the auto preheat time. 1. Display AUTO PREHEAT TIME using the Up/Down keys. 2. Set the time by pressing the +/symbols. Setting is available between 5 and 45 min. in 5 min. steps
Auto shutoff time Special paper Selects the drawer for special paper. 1. Display SPECIAL PAPER using the Up/Down keys. 2. CHANGE: ON 3. Select the drawer. To cancel, select the same drawer again. 4. End: ON Sets the auto shutoff time. 1. Display AUTO SHUT-OFF TIME using the Up/Down keys. 2. Set the time by pressing the +/symbols. Setting is available between 15 and 270 min. in 15 min. steps.
3-2-94
2AD
Management code change Changes the management code to be used. 1. Display MANAGEMENT CODE CHANGE using the Up/Down keys. 2. CHANGE: ON. 3. Enter the code using the numeric keys. 4. CHANGE: ON
Auto shutoff Sets if the auto shutoff function is available. 1. Display AUTO SHUT-OFF using the Up/Down keys. 2. Select ON or OFF.
3-2-95
2AD ( 6 ) Language Switches the language to be displayed on the key touch panel. 1. Press on the language to be displayed. Available languages are English, German, French, Italian and Spanish for metric specifications, and English, French and Spanish for inch specifications.
3-2-96
2AD-1 2AD
1-1-21
2AD 2AD-1 3-3-6 Developing section ............................................................................ 3-3-49 (1) Replacing the developing unit upper seal ................................. 3-3-49 (2) Adjusting the position of the magnetic brush (developing roller) (reference) ................................................................................. 3-3-50 (3) Adjusting the position of the doctor blade (reference) ............... 3-3-51 (4) Replacing the developing duct filter .......................................... 3-3-53 3-3-7 Transfer and separation section ....................................................... 3-3-54 (1) Replacing the charger wires and cleaning pads........................ 3-3-54 3-3-8 Cleaning section ............................................................................... 3-3-57 (1) Detaching and refitting the cleaning blade ................................ 3-3-57 (2) Detaching and refitting the cleaning brush ................................ 3-3-59 (3) Detaching and refitting the drum separation claw assembly and cleaning lower seal assembly ............................................. 3-3-61 3-3-9 Fixing section .................................................................................... 3-3-62 (1) Detaching and refitting fixing heaters M and S.......................... 3-3-62 (2) Detaching and refitting the fixing unit thermistor ....................... 3-3-66 (3) Detaching and refitting the fixing unit thermostats .................... 3-3-68 (4) Replacing the press roller .......................................................... 3-3-70 (5) Replacing the heat roller ........................................................... 3-3-72 (6) Replacing the heat roller separation claws ................................ 3-3-74 (7) Detaching and refitting the press roller separation claws .......... 3-3-75 (8) Replacing the cooling filter ........................................................ 3-3-76 (9) Replacing the ozone filter .......................................................... 3-3-77 (10) Adjusting the fixing pressure (reference)................................... 3-3-78 3-3-10 Feedshift and duplex section ............................................................ 3-3-79 (1) Detaching and refitting the duplex forwarding pulley................. 3-3-79 (2) Detaching and refitting the switchback roller, duplex upper registration roller .................................................. 3-3-80 (3) Adjusting the position of the side registration section ............... 3-3-86 (4) Adjusting the side registration amount ...................................... 3-3-87 3-3-11 SRDF section .................................................................................... 3-3-88 (1) Detaching and refitting the DF original feed pulley and the DF forwarding pulleys .......................................................... 3-3-88 (2) Detaching and refitting the DF separation pulley ...................... 3-3-90 (3) Adjusting the lateral squareness of the DF ............................... 3-3-93 (4) Adjusting the DF magnification .................................................. 3-3-95 (5) Adjusting the DF center line ...................................................... 3-3-96 (6) Adjusting the scanning start position when the DF is used ....... 3-3-97 (6-1) Adjusting the DF leading edge registration .................... 3-3-97 (6-2) Adjusting the DF traling edge registration ...................... 3-3-98 (7) Adjusting the margins for scanning the original from the DF ..... 3-3-99 3-3-12 Large paper deck section ................................................................ 3-3-101 (1) Detaching and refitting the upper and lower deck separation rollers....................................................................................... 3-3-101 (2) Detaching and refitting the deck paper conveying unit assembly ................................................................................. 3-3-102 (3) Detaching and refitting deck paper feed roller 1...................... 3-3-103 (4) Adjusting the position of the center adjuster (center line alignment) ............................................................. 3-3-104
1-1-22
2AD
3-3-1
Start
Enter the maintenance item number using the numeric keys or Up/Down keys.
Yes
No Yes
Run another maintenance item? No Enter "001" using the numeric keys or Up/Down key and press the print key. Maintenance mode is exited.
End
3-3-2
2AD
Screw
Screw
3-3-3
2AD Removing the forwarding pulley 5. Raise the forwarding pulley retainer in the direction the arrows, and remove it from the primary paper feed unit.
3-3-4
2AD 6. Remove the stop ring, pull the forwarding pulley shaft in the direction of the arrow, and remove the forwarding pulley.
Forwarding pulley
Figure 3-3-3 Detaching the forwarding pulley Removing the upper paper feed pulley 7. Remove the two stop rings. 8. Remove the paper feed clutch wires from the notches on the rear of the paper feed housing. 9. Pull the upper paper feed shaft toward the rear of the primary paper feed unit (see the arrow below) and remove the upper paper feed pulley.
Stop rings Upper paper feed shaft Notches
3-3-5
2AD Removing the lower paper feed pulley 10. Remove the stop ring on the rear of the primary paper feed unit. 11. Pull the lower paper feed shaft to the rear (see the arrow shown below).
Stop ring
3-3-6
2AD 13. Replace the forwarding pulley and upper and lower paper feed pulleys. 14. Refit all removed parts. Caution: When fitting the forwarding pulley, orient it correctly as shown in Figure 3-3-7.
Machine front Machine rear
Forwarding pulley
Figure 3-3-7 When fitting the upper paper feed pulley, keep its blue end toward the machine front. After fitting the upper paper feed pulley, refit the wires which were removed in step 8 in the paper feed housing notches. When refitting the clutch, be sure to refit the stop.
3-3-7
2AD ( 2 ) Detaching and refitting the bypass forwarding, upper and lower paper feed pulleys Replace the bypass forwarding, upper and lower paper feed pulleys as follows. <Procedure> Removing the bypass paper feed unit 1. Open the right cover and bypass table, and remove right front lower cover B, the right rear lower cover and middle right cover. 2. Detach the connector under the bypass table and then the bypass table.
Bypass table
Connector
3-3-8
2AD 3. Remove the connector and four screws holding the bypass paper feed unit, and then the unit.
Bypass paper feed unit Connector
Screws
Screws
Figure 3-3-9 Detaching the bypass paper feed unit Removing the bypass forwarding pulley 4. Remove the stop ring at the front of the bypass forwarding pulley retainer. 5. Pull out the bypass forwarding pulley shaft in the direction of the arrow, and remove the bypass forwarding pulley.
Bypass forwarding pulley retainer
3-3-9
2AD Remove the bypass uppedr paper feed pulley. 6. Remove the spring from the bypass forwarding pulley retainer. 7. Remove the stop ring. 8. Move the bushing in the direction of arrow A and remove it from the bypass forwarding pulley retainer. 9. Push the bypass solenoid lever in the direction of arrow B and remove the bypass forwarding pulley retainer in the direction of arrow C.
A
Bushing
3-3-10
2AD 10. Remove the stop ring, gear, spring pin and bushing. 11. Slightly move the bypass paper feed shaft in the direction of the arrow and remove the shaft from the bypass front frame.
Spring pin
Bushing Gear
3-3-11
2AD 12. Remove the bushing and the bypass upper paper feed pulley from the bypass paper feed shaft.
Figure 3-3-13 Detaching the bypass upper paper feed pulley Removing the bypass lower paper feed pulley 13. Remove the two screws holding the bypass separation retainer and then the retainer.
Screws
3-3-12
2AD 14. Remove the stop ring and pull the joint shaft in the direction of the arrow.
Stop ring
Joint shaft
Figure 3-3-15 Detaching the bypass lower paper feed pulley (1) 15. Remove the stop ring and then the bypass lower paper feed pulley.
Bypass lower paper feed pulley
Stop ring
Figure 3-3-16 Detaching the bypass lower paper feed pulley (2) 16. Replace the bypass forwarding, upper and lower paper feed pulleys. 17. Refit all removed parts. Caution: When refitting the upper paper feed pulley, orient its blue end toward the machine rear.
3-3-13
2AD ( 3 ) Replacing the upper and lower paper width switches (Inch models only) Replace the upper and lower paper width switches as follows. Caution: After replacing a paper width switch, be sure to perform (5) Adjusting the position of the rack adjuster. <Procedure> 1. Open the drawer. 2. Remove the four screws and take the drawer out of the machine.
Screws Screws
Drawer
Figure 3-3-17 3. 4. 5. 6. Remove the two screws and 8-pin socket from the rear of the drawer. Detach the 8-pin paper width switch connector from the 8-pin socket. Remove the three screws holding the rack adjuster. While raising the drawer lift in the direction of the arrow, remove the rack adjuster.
Screws
Rack adjuster
Drawer lift
8-pin socket
3-3-14
2AD 7. Remove the two screws from the back of the rack adjuster and then the paper width switch.
Screws Paper width switch
Figure 3-3-19 Detaching the paper width switch 8. Apply the specified grease to the printed surface of the new paper width switch (shaded area in the diagram) and fit the switch to the rack adjuster.
Apply the specified grease.
3-3-15
2AD-1 2AD
( 4 ) Replacing the upper and lower registration cleaner assemblies Replace the upper and lower registration cleaner assemblies as follows.
<Procedure> Detaching the upper registration cleaner assembly 1. Open the front cover and pull the image formation unit out. 2. Remove the screw holding the paper feed section knob and then the knob. 3. Remove the screw holding the inner right cover and then the cover. 4. Remove the screw holding the upper registration cleaner assembly. Replace the assembly. 5. Refit all removed parts. Detaching the lower registration cleaner assembly 1. Open the front cover. 2. Remove the screw holding the lower registration cleaner assembly. Replace the assembly. 3. Refit all removed parts.
Screw
Figure 3-3-21 Replacing the upper and lower registration cleaner assemblies
3-3-16
2AD ( 5 ) Adjusting the position of the rack adjuster Perform the following adjustment if there is a regular error between the centers of the original and the copy image on paper fed from the drawer. <Procedure>
Start
Original
Copy example 1
Copy example 2
Figure 3-3-22
No
Yes
Loosen the three screws holding the rack adjuster and change the position of the adjuster so that the centers of the original and the copy image are aligned. For example 1, move it toward the machine front ( ). For example 2, move it toward the machine rear ( ).
3-3-17
2AD ( 6 ) Adjustment after roller and clutch replacement Perform the following adjustment after refitting rollers and clutches. (6-1) Adjusting the leading edge registration Make the following adjustment if there is a regular error between the leading edges of the copy image and original.
U034 U 402 (P.3-3-20) U066 (P.3-3-37) U403 (P.3-3-38) U071 (P.3-3-97) U404 (P.3-3-99)
Caution: Check the copy image after the adjustment. If the image is still incorrect, perform the above adjustments in maintenance mode. <Procedure>
Start Leading edge registration
Enter "034" using the numeric keys. Correct image Press the print key. Output example 1 Output example 2
Figure 3-3-24
Selected the item to be adjusted. RCL ON DATA: Leading edge registration RCL ON DATA 2: Leading edge registration for duplex copying (second face) Press the print key The new setting is stored Press the print key and make a test copy using A3/11" 17" paper. If "RCL ON DATA 2" is selected, make a test copy in duplex copy mode.
Is the leading edge registration correct? Yes Press the stop/clear key to exit maintenance mode.
No
For output example 1, decrease the value using the Down key. For output example 2, increase the value using the Up key. Setting range: 30.0 - +30.0 Changing the value by 1 moves the leading edge by 0.5 mm. Reference Leading edge registration: 4.0 Leading edge registration for duplex copying (second face): 0
End
3-3-18
2AD-1 2AD (6-2) Adjusting the center line of image printing Make the following adjustment if there is a regular error between the center lines of the copy image and original when paper is fed from the drawer.
U 402 (P.3-3-20) U067 (P.3-3-36) U403 (P.3-3-38) U072 (P.3-3-96) U404 (P.3-3-99)
U034
Caution: Perform (5) Adjusting the position of rack adjuster before and after this adjustment. Check the copy image after the adjustment. If the image is still incorrect, perform the above adjustments in maintenance mode. <Procedure>
Start Center line of printing
Enter "034" using the numeric keys. Correct image Press the print key. Output example 1 Output example 2
Figure 3-3-25
Press the print key. The new setting is stored.
Is the image correct? Yes Press the stop/clear key to exit maintenance mode.
No
For output example 1, decrease the value using the Down key. For output example 2, increase the value using the Up key. Setting range: 30.0 - +30.0 Changing the value by 1 moves the center line by 0.5 mm. Reference: 0
End
3-3-19
2AD (6-3) Adjusting the margins for printing Make the following adjustment if the margins are not correct.
U 403 (P.3-3-38) U404 (P.3-3-99)
U402
Caution: Check the copy image after the adjustment. If the margins are still incorrect, perform the above adjustments in maintenance mode. <Procedure>
Start
Enter maintenance mode. Touch panel first display A EDGE: printer left margin C EDGE: printer right margin LEAD EDGE: printer leading edge margin (TRAIL EDGE: printer trailing edge margin) Press the stop/clear key. Touch panel second display TRAIL EDGE: printer trailing edge margin TRAIL EDGE 2: printer trailing edge margin for duplex copying (second face)
Press the print key to make a test copy using A3/11" 17" paper.
No
Change the setting using the Up/Down keys. Setting range (default) Printer leading edge margin: 0 - +10.0 (3.0) Printer trailing edge margin: 5.0 - +10.0 (5.0) Printer left/right margin: 5.0 - +10.0 (3.0) Printer trailing edge margin for duplex copying (secondface): 5.0 - +10.0 (4.0) Increasing the value makes the margin wider and decreasing it makes the margin narrower. Changing the value by 1 moves the margin by 0.1 mm for all.
3-3-20
2AD
Yes
End
Printer leading edge margin (31.0mm) Ejection direction (reference) Printer left margin (20.5mm) Printer right margin (20.5mm)
Printer trailing edge margin (31.0mm) Normal copy mode (A3/11" 17")
Figure 3-3-26
3-3-21
2AD (6-4) Adjusting the amount of slack in the paper at the registration roller for drawer, bypass and duplex feeds Make the following adjustment if the leading edge of the copy image is missing or varies randomly, or if the copy paper is Z-folded.
<Procedure>
Start Original Copy example 1 Copy example 2
Enter maintenance mode. Enter "051" using the numeric keys. Press the print key. Select the item to be adjusted. Press the interrupt key. Press the print key to make a test copy. Press the interrupt key.
Figure 3-3-27
DECK DATA: Amount of slack at the registration roller for drawer feed BYPASS DATA: Amount of slack at the registration roller for bypass feed DUPLEX DATA: Amount of slack at the registration roller for duplex feed Press the print key. The new setting is stored.
Is the leading edge of the image missing or varying randomly (copy example 1)? No
Yes
Is the copy paper Z-folded (copy example 2)? No Press the stop/clear key. Exit maintenance mode.
Yes
Decrease the value using the Down key. Setting range: 30 - +20 Changing the value by 1 changes the amount of slack by 1 mm. Reference: DECK DATA: 20 BYPASS DATA: 5 DUPLEX DATA: 25 The greater the value, the larger the amount of slack; the smaller the value, the smaller the amount of slack.
End
3-3-22
2AD
2-pin connector
Scanner
3-3-23
2AD ( 2 ) Detaching and refitting the scanner wires Take the following procedure when the scanner wires are broken or to be replaced. After replacing the scanner wires, proceed to (5) Adjusting scanner image lateral squareness (reference). (2-1) Detaching the scanner wires <Procedure> 1. Detach the SRDF connector and remove the SRDF from the machine. 2. Remove the rear cover, upper rear cover and upper right cover. 3. While taking care not to touch the shading plate or rear face of the contact glass, remove the contact glass. 4. Remove the upper left cover and slit glass. 5. Loosen the two screws securing the lamp wire and remove the wire from the inverter PCB. Caution: Remove the lamp wire completely from the machine. 6. Remove the six screws holding the front cover and then the cover. 7. Remove the four screws holding the operation unit lower and inner covers and then the covers. 8. Detach the three connectors and clamp from under the operation unit main PCB. 9. Remove the six screws holding the operation unit and then the unit. 10. Remove the four screws holding the mirror 1 upper frame and then the frame.
Screws Mirror 1 upper frame Screws Lamp wire Mirror 1 lower frame
Wire retainers
Figure 3-3-29 Detaching the mirror 1 upper frame 11. Remove the two screws from each of the wire retainers and then the retainers from the mirror 1 lower frame. 12. Remove the mirror 1 lower frame from the scanner unit.
3-3-24
2AD-1 2AD 13. Detach the round terminal of the scanner wire from the scanner wire spring on the left side of the scanner unit. 14. Remove the scanner wire.
Scanner unit
Figure 3-3-30 Detaching the scanner wire (2-2) Refitting the scanner wires Caution: When fitting the wires, be sure to use those specified below. Machine front: 2AC12170 Machine rear: 2AC12420 (black) Refitting requires the following tool: Frame securing tool (P/N: 2AC68230) <Procedure> At the machine rear: 1. Insert the two frame securing tools into the positioning holes at the front and rear of the scanner unit to pin the mirror 2 frame in position. 2. Secure the two frame securing tools at the machine front and rear using the two screws for each. 3. Hook the round terminal on one end of the scanner wire onto the left catch on the inside of the scanner unit. ....................................................................................... 1 4. Loop the scanner wire around the rear groove in the scanner wire pulley on the mirror 2 frame, winding from below to above. ........................................................ 2 5. Loop the scanner wire around the groove in the scanner wire pulley at the machine right, winding from above to below. ........................................................................ 3
(Machine left) Front groove Wire guide 2 Rear groove (Machine right) Scanner wire pulley
6
Round terminal
Catch
1 4
Scanner wire spring
3
Scanner wire drum
Round terminal
3-3-25
2AD 6. Wind the scanner wire around the scanner wire drum four turns from the rear toward the hole in the drum. 7. Insert the locating ball on the scanner wire into the hole in the scanner wire drum. 8. Wind the scanner wire a further five turns from the locating ball toward the machine front.
Locating ball
Rear
Scanner wire
Figure 3-3-32 Winding the scanner wire 9. Loop the scanner wire around the groove in the scanner wire pulley at the machine left, winding from below to above. .......................................................................... 4 10. Loop the scanner wire around the front groove in the scanner wire pulley on the mirror 2 frame, winding from below to above. ........................................................ 5 11. Run the scanner wire around the wire guide at the machine left. ........................... 6 12. Hook the round terminal onto the scanner wire spring. .......................................... 7 13. Hook the other end of the scanner wire spring onto the catch at the machine left. 14. Repeat steps 2 to 13 for the scanner wire at the machine front. 15. Remove the two screws from each of the frame securing tools and then the tools. 16. Move the scanner from side to side to correctly locate the wire in position.
3-3-26
2AD 17. Loosen the two screws securing the mirror 2 frame. 18. Insert the mirror 1 lower frame into the scanner unit and seat it on the positioning holes. 19. Insert the two frame securing tools into the positioning holes in the front and rear of the scanner unit and determine the positions of the mirror 1 lower frame and mirror 2 frame. 20. While holding the scanner wire on the mirror 1 lower frame, secure the wire retainers at the front and rear of the mirror 1 lower frame using the two screws for each.
Screws Frame securing tool
Wire retainer
Mirror 2 frame
21. Retighten the two screws securing the mirror 2 frame. 22. Remove the two screws holding each of the two frame securing tools and then the tools. 23. Refit all removed parts.
3-3-27
2AD ( 3 ) Replacing the laser scanner unit Take the following procedure when the laser scanner unit is to be checked or replaced. Caution: After replacing the laser scanner unit, proceed to (5) Adjusting scanner image lateral squareness (reference). <Procedure> 1. Remove the SRDF, rear cover, upper rear cover, upper right cover and upper left cover. 2. Remove the six screws holding the front cover and then the cover. 3. Pull the image formation unit out. 4. Remove the four screws holding the operation unit lower and inner covers and then the covers. 5. Detach the three connectors and clamp from under the operation unit main PCB. 6. Remove the six screws holding the operation unit and then the unit. 7. Remove the five clamps and two connectors at the front of the scanner unit. 8. Remove the five clamps and twelve connectors at the rear of the scanner unit. 9. Remove the screw holding the two grounding wires at the rear of the scanner unit and then the wires. 10. Remove the wires detached in steps 7, 8 and 9 from the scanner unit. 11. While taking care not to touch the shading plate or rear face of the contact glass, remove the contact glass. 12. Remove the ISU and lower ISU covers, and detach the three connectors. 13. Remove the four screws with rubber mounts and then the scanner unit.
Screws Screws
Scanner unit
Connectors
3-3-28
2AD 14. Detach the three connectors. 15. Remove the two screws holding the LSU adjuster mount and then the mount. 16. Remove the three pins and replace the laser scanner unit. 17. Refit all removed parts. Caution: When fitting the scanner unit, fit from directly above the machine to prevent deformation of the grounding point.
Pins
Connectors
Screws
3-3-29
2AD-1 2AD
( 3-1 ) Replacing the ISU (reference) Take the following procedure when the ISU is to be checked or replaced. Caution: After fitting the ISU, proceed to (5-2) Adjusting the position of the ISU. <Procedure> 1. Remove the upper right cover. 2. While taking care not to touch the shading plate or rear face of the contact glass, remove the contact glass. 3. Remove the ISU and lower ISU covers, and detach the two connectors.
Screws
Screws Screws
ISU
Connectors
Figure 3-3-35-1 Detaching the ISU and lower ISU covers 4. Remove the four screws holding the ISU and then the ISU. 5. Check or replace the ISU. 6. Refit all removed parts.
3-3-29-1 3-3-30
2AD-1 2AD
Securing the ISU <ISU installation requires the following tools:> Two (2) positioning pins (P/N 18568120) <Procedure> 1. Secure the ISU using the two positioning pins. 2. Refit the four screws. 3. Remove the two positioning pins.
Screws ISU
Positioning pin
3-3-29-2 3-3-31
2AD ( 4 ) Adjusting the longitudinal squareness (reference) Perform the following adjustment if the copy image is longitudinally skewed (longitudinal squareness is not obtained). Caution: Before making the following adjustment, output a 1 DOT-LINE PG pattern in maintenance item U089 to use as the original for the adjustment. Adjust the amount of slack in the paper at the registration roller for drawer, bypass and duplex feeds (page 3-3-22) first. Check for the longitudinal squareness of the copy image, and if it is not obtained, perform the longitudinal squareness adjustment.
<Procedure>
Start Correct image Place the original on the contact glass. Copy example 1 Copy example 2
Figure 3-3-36
Retighten the two screws and refit the contact glass.
Press the print key and make a test copy at 100% magnification.
No
Yes
Remove the contact glass. Loosen the two screws and adjust the position of the mirror 2 frame. For copy example 1, move the frame in the direction of the white arrow (e). For copy example 2, move the frame in the direction of the black arrow (b).
End
Mirror 2 frame
Screws
3-3-30 3-3-32
2AD ( 5 ) Adjusting scanner image lateral squareness (reference) Perform the following adjustment if the copy image is laterally skewed (lateral squareness not obtained). Caution: Before making the following adjustment, open the front cover and remove the operation unit lower cover. Perform (5-1) Adjusting the position of the laser scanner unit first and check for lateral squareness of the copy image. If squareness is not obtained, perform (5-2) Adjusting the position of ISU. (5-1) Adjusting the position of the laser scanner unit <Procedure>
Start
Correct image
Output example 1
Output example 2
Figure 3-3-38
Press the interrupt key. Remove the contact glass. Loosen the three screws and adjust the position of the laser scanner unit by rotating the LSU adjustment shaft from the machine front using a straight screwdriver (see Figure 3-3-39). For output example 1, rotate the LSU adjustment shaft in the direction of the white arrow (e). For output example 2, rotate the LSU adjustment shaft in the direction of the black arrow (b).
No
End
3-3-31 3-3-33
2AD
Pin holes
3-3-32 3-3-34
2AD (5-2) Adjusting the position of the ISU Caution: Before making the following adjustment, output a 1 DOT-LINE PG pattern in maintenance item U089 to use as the original for the adjustment. Adjust the pin at the machine front only and never touch the one at the machine rear. <Procedure>
Start
Correct image
Copy example 1
Copy example 2
Figure 3-3-40
Press the print key and make a test copy at 100% magnification. Refit the contact glass.
No
Yes
End
Remove the contact glass and adjust the lateral squareness of the ISU by rotating the pin. For copy example 1, rotate the pin in the direction of the black arrow (\). For copy example 2, rotate the pin in the direction of the white arrow (e).
Pin
3-3-33 3-3-35
2AD ( 6 ) Adjusting magnification of the scanner in the main scanning direction Perform the following adjustment if the magnification in the main scanning direction is not correct.
U 066 (P.3-3-37) U403 (P.3-3-38)
U065
Caution: Check the copy image after the adjustment. If the image is still incorrect, perform the above adjustments in maintenance mode. <Procedure>
Start Enter maintenance mode. Enter "065" using the numeric keys. Original Press the print key. Select "MAIN SCAN ADJ" (main scanning direction). Press the interrupt key. Place an original and press the print key to make a test copy. Press the interrupt key. For copy example 1, increase the value using the Up key. For copy example 2, decrease the value using the Down key. Setting range: 25 - +25 Reference: 0 Changing the value by 1 changes the magnification by 0.1%. Increasing the value makes the image wider, and decreasing it makes the image narrower. Press the print key. The new setting is stored. Copy example Copy example 2
Figure 3-3-42
No
End
3-3-34 3-3-36
2AD ( 7 ) Adjusting magnification of the scanner in the auxiliary scanning direction Perform the following adjustment if the magnification in the auxiliary scanning direction is not correct.
U053 (P.3-2-20) U034 (P.3-3-18) U403 (P.3-3-38) U402 (P.3-3-20) U070 (P.3-3-95) U066 (P.3-3-37) U404 (P.3-3-99)
U065
U071 (P.3-3-97)
Caution: Before making the following adjustment, ensure that the above adjustments have been made in maintenance mode. <Procedure>
Start Enter maintenance mode. Enter "065" using the numeric keys. Original Press the print key. Select "SUB SCAN ADJ" (auxiliary scanning direction). Press the interrupt key. Place an original and press the print key to make a test copy. Press the interrupt key. For copy example 1, increase the value using the Up key. For copy example 2, decrease the value using the Down key. Setting range: 25 - +25 Reference: 0 Changing the value by 1 changes the magnification by 0.1%. Increasing the value makes the image longer, and decreasing it make the image shorter. Press the print key. The new setting is stored. Copy example Copy example 2
Figure 3-3-43
No
End
3-3-35 3-3-37
2AD-1 2AD ( 8 ) Adjusting the scanner center line Perform the following adjustment if there is a regular error between the center lines of the copy image and original.
U034 (P.3-3-19) U 402 (P.3-3-20) U403 (P.3-3-38) U072 (P.3-3-96) U404 (P.3-3-99)
U067
Caution: Before making the following adjustment, ensure that the above adjustments have been made in maintenance mode. <Procedure>
Scanner center line
Start
Original
Press the print key.
Copy sample 1
Copy sample 2
Figure 3-3-44
Press the print key. The new setting is stored.
Is the scanner center line correct? Yes Press the stop/clear key.
No
For copy sample 1, decrease the value using the Down key. For copy sample 2, increase the value using the Up key. Setting range: 39.0 - +39.0 Changing the value by 1 moves the center line by 0.17 mm Reference: 0
End
3-3-36 3-3-38
2AD-1 2AD ( 9 ) Adjusting the scanner leading edge registration Perform the following adjustment if there is regular error between the leading edges of the copy image and original.
U034 (P.3-3-18) U 402 (P.3-3-20) U403 (P.3-3-38) U071 (P.3-3-97) U404 (P.3-3-99)
U066
Caution: Before making the following adjustment, ensure that the above adjustments have been made in maintenance mode. <Procedure>
Start
Original
Copy sample 1
Copy sample 2
Figure 3-3-45
Press the print key. The new setting is stored.
Is the scanner leading edge registration correct? Yes Press the stop/clear key.
No
For copy sample 1, decrease the value using the Down key. For copy sample 2, increase the value using the Up keys. Setting range: 32.0 - +32.0 Changing the value by 1 moves the leading edge by 0.17 mm. Reference: 0
End
3-3-37 3-3-39
2AD (10) Adjusting the margins for scanning an original on the contact glass Perform the following adjustment if the margins are not correct.
U402 (P.3-3-20) U404 (P.3-3-98)
U403
Caution: Before making the following adjustment, ensure that the above adjustments have been made in maintenance mode. <Procedure>
Start
Touch panel display SCAN A MARGIN: scanner left margin SCAN B MARGIN: scanner leading edge margin SCAN C MARGIN: scanner right margin SCAN D MARGIN: scanner trailing edge margin
Change the setting. Increasing the value using the Up key makes the margin wider. Decreasing the value using the Down key makes the margin narrower. Setting range (default) Scanner left margin: 0 - +20 (2) Scanner leading edge margin: 4 - +20 (6) Scanner right margin: 0 - +20 (2) Scanner trailing edge margin: 0 - +20 (6) Changing the value by one moves the margin by 0.5 mm for all.
No
3-3-38 3-3-40
2AD
B A
Yes
End
Scannerleading edge margin(31.0mm) Ejection direction (reference) Scanner left margin (21.0mm) Scanner right margin (21.0mm)
Figure 3-3-46
3-3-39 3-3-41
2AD
3-3-40 3-3-42
2AD 3. Remove the screw holding the grid tension plate and then the plate and main charger grid. 4. Remove the main charger front and rear lids. 5. Remove the charger spring from the charger wire retainer pin and charger terminal, and then the charger wire.
Grid tension plate Main charger rear lid Charger wire retainer pin Charger spring Charger wire
Charger terminal
3-3-41 3-3-43
2AD
Charger terminal
Charger wire retainer pin Not more than 2 mm Projection 13 2 mm Charger terminal
Not more than 2 mm Charger spring Charger wire retainer pin Main charger front housing Main charger rear housing
Figure 3-3-49 Installing the charger wire 6. Wind the new tungsten wire at least five turns around one end of the charger spring and trim the end. The width of the coiled charger wire and the cut end must be within 2 mm. 7. Hook the other end of the charger spring onto the charger terminal of the main charger rear housing. 8. Pass the wire through the notch in the charger wire retainer pin and stretch it taut. The charger wire must be adjusted so that the charger spring stretches to 13 2 mm and the spring end aligns with the rib on the main charger rear housing. 9. Hook the charger wire onto the projection on the main charger front housing. 10. Insert the charger wire retainer pin into the projection on the main charger rear housing to secure the charger wire. 11. Cut off the excess wire under the charger wire retainer pin. The cut end of the charger wire must protrude less than 2 mm. 12. Refit the main charger front and rear lids. 13. Refit all removed parts.
3-3-42 3-3-44
2AD
3-3-43 3-3-45
2AD 3. Remove the two screws holding the main charger assembly and then the assembly.
Figure 3-3-51 Detaching the main charger assembly 4. Loosen the cleaning blade pin. Move the cleaning blade lever in the direction of the arrow so that the cleaning blade is kept away from the drum and then tighten the cleaning blade pin. 5. Remove the two screws and open the upper cleaning cover on the left of the drum. 6. Remove the two screws and open the image formation rail in the direction of the arrow.
Screw
Figure 3-3-52
3-3-44 3-3-46
2AD-1 2AD 7. Detach the 1-pin and 4-pin connectors. 8. While raising the toner sub-hopper slightly, slide the hopper toward the front of the image formation unit and turn the image formation unit to the right.
Toner sub-hopper
1-pin connector
4-pin connector
Figure 3-3-53
9. Move the developing unit to the right of the image formation unit and remove it from the unit. 10. Remove one screw each from the drum front and rear retainers and then the drum from the image formation unit.
Drum rear retainer Drum front retainer Screw Drum Screw
Developing unit
3-3-45 3-3-47
2AD 11. Remove the drum front and rear retainers from the drum. Replace the drum.
Drum rear retainer
Drum
3-3-46 3-3-48
2AD 12. Refit all removed parts. Important: After replacing the drum, run maintenance items U110 "Checking/clearing the drum count" and U111 "Checking/clearing the drum drive time." After running maintenance item U160, loosen the blade pin and position the cleaning blade against the drum. When installing the drum, orient correctly with the thinner end of the drum flange shaft at the machine front and the thicker end at the machine rear.
Drum flange Drum Drum flange
Machine front
Machine rear
Figure 3-3-56 When refitting the toner sub-hopper, align the toner sub-hopper hole with the developing unit hole and connect the coupling to the joint. When installing the main charger assembly, fix the assembly pushed all the way toward the machine front.
Hole
Hole
Joint
Figure 3-3-57
3-3-47 3-3-49
2AD ( 2 ) Cleaning the drum Clean the drum as follows when an image problems occur or if the drum is dirty. <Precautions> Avoid direct sunlight and strong light when cleaning the drum. Dust in the air and from the cleaning pad may damage the drum during operation. Avoid working in dusty places. Clean the drum entirely even if it is only dirty locally. Do not clean the drum with alcohol or other organic solvent. Required supplies: Polishing cloth: specified synthetic cotton Toner <Procedure> 1. Remove the drum from the imaging unit (see page 3-3-43). 2. Apply a polishing cloth to the drum and gently wipe the drum taking care not to damage the surface. 3. Apply toner to another cloth and wipe the drum surface with it in the same manner. 4. Refit the drum. 5. Refit all removed parts and let the machine stand for 30 minutes. 6. Make a test copy and check the image.
3-3-48 3-3-50
2AD
Screws
3-3-49 3-3-51
2AD ( 2 ) Adjusting the position of the magnetic brush (developing roller) (reference) Perform the following adjustment if the image is abnormally dark or light. Before starting this adjustment, ensure that the doctor blade is installed correctly and that the correct amount of developer is present. <Procedure> 1. Loosen the hexagonal socket head screw holding the developing sleeve front bushing using a hexagonal wrench. 2. Turn the developing roller shaft using a straight screwdriver until the distance between the top of the magnetic brush and the bottom of the developing unit housing is 15 mm (reference). 3. Tighten the hexagonal socket head screw to secure the developing roller shaft. If the distance is smaller than the specified value, carrier or background appears on the copy image. 4. After adjustment, make a test copy to check for performance.
Developing sleeve front bushing
A=15mm
3-3-50 3-3-52
2AD ( 3 ) Adjusting the position of the doctor blade (reference) Perform the following adjustment if carrier or background appears on the copy image. <Procedure> 1. Remove the two screws holding the developing unit upper seal, and then the seal. When refitting the seal, fit while holding it upward. 2. Remove the two screws, disengage the two hooks and detach the developing unit upper cover.
Screws
Hook
Screws
3-3-51 3-3-53
2AD 3. Measure the distance between the developing roller and the doctor blade with a thickness gauge as shown in Figure 3-3-43, and adjust the doctor blade until the correct distances are obtained at the center and ends of the developing unit housing; the 0.50 mm gauge should go into the gap and the 0.55 mm one should not. The smaller the distance, the lighter the image; the larger the distance, the darker the image.
Adjustment screw Adjustment screw Adjustment screw
Developing roller
Doctor blade
Figure 3-3-62
3-3-52 3-3-54
2AD-1 2AD ( 4 ) Replacing the developing duct filter Replace the developing duct filter as follows. <Procedure> 1. Open the front cover. 2. Slide off the developing duct cover downward. 3. Replace the developing duct filter. Caution: When fitting the developing duct filter, ensure that the harder side of the filter faces the fan. 4. Refit all removed parts.
3-3-53 3-3-55
2AD
Connector
Pin
3-3-54 3-3-56
2AD 3. 4. 5. 6. Remove the transfer charger front and rear lids. Remove the separation guide. Replace the transfer charger cleaning pad and separation charger cleaning pad. Remove the charger wire retainer pins, charger springs and then the charger wires.
Transfer charger rear lid
Separation guide
Charger springs
3-3-55 3-3-57
2AD 7. Wind one end of the new wire at lease five turns around the end of the charger spring. 8. Hook the other end of the charger spring onto the catch on the transfer charger terminal on the rear of the transfer charger housing. 9. Pass the charger wire through the notches in the front and rear of the transfer charger housing, and stretch it. 10. Insert the charger wire under the charger wire retainer pin into the hole at the front of the transfer charger housing. The charger wire must be adjusted so that the charger spring stretches to 12.5 1.5 mm. Cut off the excess wire under the charger wire retainer pin. 11. Refit all removed parts. When installing the main charger assembly, fix the assembly pushed all the way toward the machine front.
Front of the transfer charger housing Charger spring
12.5 1.5 mm
Charger wire
3-3-56 3-3-58
2AD
Cleaning blade
Pin
3-3-57 3-3-59
2AD 5. Refit all removed parts. When installing the cleaning blade, take care not to trap the sponges at both ends. After replacing the cleaning blade, move it away from the drum and run maintenance item U160 (see page 3-2-48).
Cleaning blade
Sponge
Sponge
3-3-58 3-3-60
2AD ( 2 ) Detaching and refitting the cleaning brush Clean or replace the cleaning brush as follows. <Procedure> 1. Remove the developing unit, main charger assembly and drum. 2. Remove the cleaning spring.
Cleaning spring
Figure 3-3-69 3. Shift the thrust spring toward the machine rear and detach the cleaning blade shaft.
Cleaning blade shaft
Thrust spring
Figure 3-3-70
3-3-59 3-3-61
2AD 4. Detach the 2-pin connector and remove the cleaning unit from the image formation unit. 5. Remove the E-rings, bushings and gear from both ends of the cleaning brush. 6. Clean or replace the cleaning brush. 7. Refit all removed parts. When installing the cleaning brush, position the end with the D-section at the machine rear and take care not to pinch the cleaning lower seal assembly.
2-pin connector
Cleaning unit
D-section
Figure 3-3-71
3-3-60 3-3-62
2AD ( 3 ) Detaching and refitting the drum separation claw assembly and cleaning lower seal assembly. Clean or replace the drum separation claw assembly and cleaning lower seal assembly as follows. <Procedure> 1. Remove the developing unit, main charger assembly and drum. 2. Remove the four screws holding the drum separation claw assembly and then the assembly. 3. Remove the two screws holding the cleaning lower seal assembly and then the assembly. 4. Replace the drum separation claw assembly and cleaning lower seal assembly.
Screw
Figure 3-3-72 Detaching the drum claw assembly and cleaning lower seal assembly 5. Refit all removed parts.
3-3-61 3-3-63
2AD
Fixing unit
Screw
3-3-62 3-3-64
2AD 3. Open the fixing unit cover in the direction of the arrow. 4. Remove the two screws holding the fixing unit front cover and then the cover. 5. Remove the screw and two pins holding the fixing unit upper cover, and then the cover.
Fixing unit upper cover Pins holding the fixing unit cover
Figure 3-3-74 Detaching the fixing unit front cover and cover
3-3-63 3-3-65
2AD 6. Detach the two fixing heater wires from the fixing unit thermostat on the front of the fixing unit. 7. Detach the two connectors on the fixing heater wire on the rear of the fixing unit.
Fixing heater wires
3-3-64 3-3-66
2AD 8. Remove the screw holding the fixing heater front retainer and then the retainer. 9. Pull fixing heaters M and S out from the front of the fixing unit.
S M Screw
Fixing heater M
Fixing heater S
Figure 3-3-76 Detaching fixing heaters M and S 10. Replace fixing heaters M and S. When fitting, place fixing heater M on the right and S on the left, as viewed form the fixing unit front. Fit the red connector on the rear of the fixing unit to heater M, and the white one to heater S. 11. Refit all removed parts.
3-3-65 3-3-67
2AD ( 2 ) Detaching and refitting the fixing unit thermistor Replace the fixing unit thermistor as follows. <Procedure> 1. Detach the connector. 2. Remove the screw holding the fixing unit thermistor and then the thermistor.
Connector
3-3-66 3-3-68
2AD 3. Replace the thermistor. When fitting the fixing unit thermistor, pass the projection on the thermistor through the hole in the fixing unit thermistor film and then insert into the cutout in the fixing unit stay.
Fixing unit thermistor Projection
Cutout
Figure 3-3-78 Installing the fixing unit thermistor 4. Refit all removed parts.
3-3-67 3-3-69
2AD ( 3 ) Detaching and refitting the fixing unit thermostats Replace the fixing unit thermostats as follows. Caution: Use the specified thermostat for replacement. Do not substitute a simple wire or similar; otherwise, the machine will be seriously damaged. <Procedure> 1. Remove the connectors of the fixing unit wires and fixing heater wire for each fixing unit thermostat by pushing the projection on each connector in. 2. Remove the two screws each from the thermostats and then the thermostats.
Screws Fixing unit wire Screws
3-3-68 3-3-70
2AD 3. Replace the fixing unit thermostats. When fitting, check the temperature indications on the thermostat detecting surface and install the thermostats on the fixing unit stay in the correct positions.
Fixing unit stay
1 4 0C
150 C
Temperature indication
Figure 3-3-80 Refitting the fixing unit thermostats 4. Refit all removed parts.
3-3-69 3-3-71
2AD ( 4 ) Replacing the press roller Replace the press roller as follows. <Procedure> 1. Remove the two screws and open the fixing unit stay in the direction of the arrow.
Screw
3-3-70 3-3-72
Press roller
Figure 3-3-82 Detaching the press roller 3. Remove the E-ring on either the front or rear end of the press roller and pull out the press roller shaft.
E-ring
E-ring
Figure 3-3-83 Detaching the press roller shaft 4. Replace the press roller. 5. Refit all removed parts.
3-3-71 3-3-73
2AD ( 5 ) Replacing the heat roller Replace the heat roller as follows. <Procedure> 1. Remove fixing heaters M and S (see page 3-3-62). 2. Open the fixing unit stay (see page 3-3-70). 3. Loosen the screw holding each of the fixing unit front and rear frames and move the heat roller stopper in the direction of the arrow. 4. Remove the heat roller.
Heat roller
Screw
3-3-72 3-3-74
2AD 5. Remove the circlip, bearing and bushing from the front end of the heat roller. 6. Remove the circlip, gear, bearing and bushing from the rear end of the heat roller. 7. Replace the heat roller.
Circlip Bearing
Gear Bearing
Bushing
Heat roller
Bushing
Circlip
Figure 3-3-85 Refitting the heat roller 8. Refit all removed parts.
3-3-73 3-3-75
2AD ( 6 ) Replacing the heat roller separation claws Replace the heat roller separation claws as follows. <Procedure> 1. Open the fixing unit cover. 2. Remove the E-ring from the heat roller separation claw shaft and the springs from the seven heat roller separation claws. 3. Remove the heat roller separation claws from the fixing unit upper guide. 4. Replace the heat roller separation claws.
Heat roller separation claws
E-ring
Springs
Figure 3-3-86 Detaching the heat roller separation claws 5. Refit all removed parts.
3-3-74 3-3-76
2AD ( 7 ) Detaching and refitting the press roller separation claws Replace the press roller separation claws as follows. <Procedure> 1. Open the fixing unit cover. 2. Remove the two E-rings from each of the press roller separation claws and then the four claws. 3. Replace the press roller separation claws.
Figure 3-3-87 Detaching the press roller separation claws 4. Refit all removed parts.
3-3-75 3-3-77
2AD ( 8 ) Replacing the cooling filter Replace the cooling filter as follows. <Procedure> 1. Remove the screw holding the ozone filter retainer and then the retainer. 2. Replace the cooling filter.
Cooling filter
Screw
Figure 3-3-88 Detaching the cooling filter 3. Refit all removed parts.
3-3-76 3-3-78
2AD ( 9 ) Replacing the ozone filter Replace the ozone filter as follows. <Procedure> 1. Remove the two screws holding the lower left cover and then the cover. 2. Remove the four screws holding the middle right cover and then the cover. 3. Replace the ozone filter.
Ozone filter
Figure 3-3-89 Fitting the ozone filter 4. Refit all removed parts.
3-3-77 3-3-79
2AD (10) Adjusting the fixing pressure (reference) Adjust fixing pressure when paper creases, fixing is defective, or after the fixing pressure spring is replaced. <Procedure>
Start Enter maintenance mode. Enter "161" using the numeric keys and press the print key. Press the interrupt key. Press the print key. 7.00.5 mm
Fixing pressure: 210 N (both machine front and rear) Figure 3-3-90
Press the interrupt key. Wait for 30 s and remove the jammed paper manually.
Is the width of the black band printed on the image (indicating the part which stopped in the fixing section) 7.0 0.5 mm? Yes Exit maintenance mode.
No
Clean the heat and press roller if they are dirty. End
Figure 3-3-91
3-3-78 3-3-80
2AD
Projections
Stop ring
Figure 3-3-92
3-3-79 3-3-81
2AD 2AD-1
( 2 ) Detaching and refitting the switchback roller, duplex upper registration roller Replace the switchback roller and duplex registration roller as follows.
<Procedure> Detaching the switchback roller 1. Open the front cover and then the duplex cover. 2. Loosen the three screws at the front of the duplex unit. Remove the two screws on the top and then the duplex unit cover.
Screws
3-3-80 3-3-82
2AD 2AD-1 3. Remove the four screws and the duplex unit from the rails. 4. Remove the two screws holding the duplex cover and then the cover. 5. Detach the 6-pin connector of the side registration section and the 3-pin connector of the side registration home position switch, and unlock the edging. 6. Remove the paper tapping guide by gently bending it and taking out of the hole in the machine rear first. 7. Remove the four screws holding the side registration section and slide off the section toward the machine right. 8. Remove the two screws holding the duplex paper conveying upper cover and then the cover.
Screws 3-pin connector Screws Screws 6-pin connector
Screw
Duplex cover
Figure 3-3-94 Detaching the duplex cover and side registration section
3-3-81 3-3-83
2AD 2AD-1
9. Remove the screw holding the switchback feedshift solenoid and then the solenoid.
Screw
Bushing E-ring
3-3-82 3-3-84
2AD 11. Remove the E-ring and then the fixing drive gear at the rear of the duplex unit. 12. Remove the pin, E-ring and bushing. 13. Remove the stop ring holding the switchback roller and then the roller from the shaft. When refitting the switchback roller, fit so that it turns in the same direction as the shaft when the shaft is turned in the direction of the white arrow.
Stop ring
Switchback roller
3-3-83 3-3-85
2AD 2AD-1
Detaching the duplex upper registration roller 1. Loosen the three screws at the front of the duplex unit. Remove the two screws on the top and then the duplex unit cover. 2. Remove the screw holding the switchback feedshift solenoid and then the solenoid. 3. Remove the E-ring and then the bushing at the tront of the duplex unit.
Bushing E-ring
3-3-84 3-3-86
2AD 2AD-1 4. Remove the two screws holding the stock switch mount and then the mount. 5. Remove the E-ring the at the rear of the duplex unit and then the duplex registration gear. 6. Remove the spring pin and bushing, and then the duplex upper registration roller.
Duplex upper registration roller
3-3-85 3-3-87
2AD ( 3 ) Adjusting the position of the side registration section Perform the following adjustment if there is a regular error between the centers of the original and copy image during duplex copying (second face). <Procedure>
Figure 3-3-100
Make a test copy at 100% and using the largest size paper in duplex mode. Loosen the four screws holding the side registration section, move the section and retighten the screws. Is the center of the image aligned with that of original? Yes End No For copy example 1, move the section toward the machine front ( ). For copy example 2, move the section toward the machine rear ( ).
Screws
3-3-86 3-3-88
2AD ( 4 ) Adjusting the side registration amount Perform the following adjustment if paper is fed askew during refeed from the duplex unit. Side registration <Procedure>
Start rear guide Paper
Enter maintenance mode. Side registration front guide A : 1 mm Press the print key.
Figure 3-3-102
Press "TEST RUN." Press the print key. The new setting is stored. Press the interrupt key to make a test copy using A3/11" x 17" paper. After paper is stocked in the duplex unit, open the unit and move the paper all the way to the side registration rear guide. Change the setting using the Up/Down keys. Increasing the value makes the gap narrower, decreasing it makes the gap wider. Setting range: 20 - +20 Reference: 0 Changing the value by 1 changes the gap by 0.3 mm.
Is gap A between the paper and the side registration front guide within 1 mm? Yes Remove the paper and reinstall the duplex unit.
No
End
3-3-87 3-3-89
2AD
Figure 3-3-103 Detaching the original feed pulley assembly Detaching the DF original feed pulley 4. Remove the two stop rings and then the DF original feed pulley from the original feed front shaft.
3-3-88 3-3-90
2AD Detaching DF forwarding pulleys 5. Remove the stop ring and bushing. While lifting the forwarding shaft, remove the DF forwarding pulleys. 6. Clean or replace the DF original feed pulley and DF forwarding pulleys. 7. Refit all removed parts. When fitting the DF original feed pulley and DF forwarding pulleys, ensure that the side having the one-way clutch faces the machine rear.
One-way clutch DF forwarding pulleys DF original feed pulley 28
Forwarding shaft
Stop ring
DF forwarding belt
Bushing
3-3-89 3-3-91
2AD ( 2 ) Detaching and refitting the DF separation pulley Clean or replace the DF separation pulley as follows. <Procedure> 1. Open the DF reversing cover. 2. Remove the two screws holding the upper original feed section cover and then the cover. 3. Remove the two screws holding the DF rear cover. 4. Remove the screw holding the fulcrum pin and then the pin. 5. Detach the 6-pin connector and remove the original table.
Figure 3-3-106
3-3-90 3-3-92
2AD 6. Remove the two screws holding the DF original feed lower guide and the two screws holding the DF original feed upper guide. 7. Loosen the other two screws on the DF original feed lower guide. 8. While lifting the DF original feed upper guide and pressing the original set switch actuator, remove the DF original feed lower guide.
Figure 3-3-107 9. Detach the original set switch 3-pin connector. 10. Remove the two screws holding the separation pulley retainer.
3-pin connectors
Figure 3-3-108
3-3-91 3-3-93
2AD 11. Remove the two stop rings and pin to remove the DF separation pulley from the separation shaft. 12. Clean or replace the DF separation pulley. 13. Refit all removed parts. When fitting the DF separation pulley, ensure that the side having the one-way clutch faces the machine rear.
3-3-92 3-3-94
2AD ( 3 ) Adjusting the lateral squareness of the DF Perform the following adjustment if the copy image is skewed laterally (lateral squareness is not obtained). Caution: Before making the following adjustment, output a 1 DOT-LINE PG pattern in maintenance item U089 to use as the original for the adjustment. Adjust the amount of slack in the paper at the registration roller for drawer, bypass and duplex feeds (page 3-3-22) and the scanner image lateral squareness (reference, page 3-3-31) first. Check for lateral squareness of the copy image and if squareness is not obtained, adjust the lateral squareness of the DF. <Procedure>
Original Start
Copy example 1
Copy example 2
Figure 3-3-110
Place the original on the SRDF. Adjustment on a machine with no adjustable hinge (Figure 3-3-111) Press the print key to make a test copy. Loosen the four screws and adjust the position of the SRDF. For copy example 1, move the SRDF in the direction of the white arrow (e). For copy example 2, move the SRDF in the direction of the black arrow (b).
No
Yes
Adjustment on a machine equipped with an adjustable hinge (Figure 3-3-112) Adjust the position of the SRDF. For copy example 1, rotate the adjustment screw in the direction of the white arrow (e). For copy example 2, rotate the adjustment screw in the direction of the black arrow (b).
End
3-3-93 3-3-95
2AD Adjustment on a machine with no adjustable hinge (Figure 3-3-111): 1. Disconnect the SRDF connector and remove the SRDF from the machine. 2. Loosen the four screws securing the right leg of the SRDF. 3. Adjust the position of the SRDF by moving the right leg back and forth. 4. Retighten the four screws loosened in step 2. 5. Refit all removed parts. Adjustment on a machine equipped with an adjustable hinge (Figure 3-3-112): 1. Open the SRDF. 2. Loosen the screw securing the right leg of the SRDF on the right. 3. Adjust the position of the SRDF by rotating the adjustment screw behind the right leg of the SRDF. 4. Retighten the screw loosened in step 2. 5. Refit all removed parts.
Screws
Screw
Figure 3-3-111
SRDF right leg Adjustable hinge Adjustment screw
Figure 3-3-112
3-3-94 3-3-96
2AD ( 4 ) Adjusting the DF magnification Adjust magnification in the auxiliary scanning direction if magnification is incorrect when the DF is used.
U053 (P.3-2-20) U034 (P.3-3-18) U403 (P.3-3-38) U402 (P.3-3-20) U070 U065 (P.3-3-35) U071 (P.3-3-97) U066 (P.3-3-37) U404 (P.3-3-99)
Caution: Before making the following adjustment, ensure that the above adjustments have been made in maintenance mode. <Procedure>
Start Main scanning direction
Original
Copy example 1
Copy example 2
Figure 3-3-113
Place an original on the DF and make a test copy. Press the print key. The new setting is stored. Press the interrupt key. Change the setting. For copy example 1, increase the value using the Up key to make the copy image longer. For copy example 2, decrease the value using the Down keys to make the copy image shorter. Setting range: 25 - +25 Changing the value by 1 changes the magnification by 0.1%. Reference: 0
No
End
3-3-95 3-3-97
2AD ( 5 ) Adjusting the DF center line Perform the following adjustment if there is a regular error between the centers of the original and the copy image.
U034 (P.3-3-19) U 402 (P.3-3-20) U067 (P.3-3-36) U403 (P.3-3-38) U404 (P.3-3-99)
U072
Caution: Before making the following adjustment, ensure that the above adjustments have been made in maintenance mode. <Procedure>
Start
Reference
Original
Copy example 1
Copy example 2
Figure 3-3-114
No
Change the setting. For copy example 1, increase the value using the Up key. For copy example 2, decrease the value using the Down key. Setting range: 39.0 - +39.0 Changing the value by 1 moves the center line by 0.17 mm. Reference: 0
End
3-3-96 3-3-98
2AD ( 6 ) Adjusting the scanning start position when the DF is used Perform the following adjustment if there is a regular error between the leading or trailing edges of the original and the copy image.
U034 (P.3-3-18) U 402 (P.3-3-20) U066 (P.3-3-37) U403 (P.3-3-38) U404 (P.3-3-99)
U071
Caution: Before making the following adjustment, ensure that the above adjustments have been made in maintenance mode. (6-1) Adjusting the DF leading edge registration <Procedure>
Start
Enter "071" using the numeric keys and press the print key.
Original
Copy example 1
Copy example 2
Figure 3-3-115
Press the interrupt key. For copy example 1, increase the value using the Up key. For copy example 2, decrease the value using the Down key. Setting range: 32 - +32 Reference: 0 Changing the value by 1 moves the copy image by 0.19 mm. Increasing the value moves the copy image backward, and decreasing it moves the image forward.
No
End
3-3-97 3-3-99
Start Enter maintenance mode. Enter "071" using the numeric keys and press the print key. To adjust the DF trailing edge registration, select "TRAIL EDGE ADJ." Press the interrupt key. Place an original on the DF and make a test copy. Press the interrupt key. For copy example 1, increase the value using the Up key. For copy example 2, decrease the value using the Down key. Setting range: 32 - +32 Reference: 0 Changing the value by 1 moves the copy image by 0.19 mm. Increasing the value moves the copy image backward, and decreasing it moves the image forward.
Original
Copy example 1
Copy example 2
Figure 3-3-116
No
3-3-98 3-3-100
2AD ( 7 ) Adjusting the margins for scanning the original from the DF Perform the following adjustment if margins are not correct.
U402 (P.3-3-20) U403 (P.3-3-38)
U404
Caution: Before making the following adjustment, ensure that the above adjustments have been made in maintenance mode. <Procedure>
Start
Press the print key. Touch panel display DF A MARGIN: DF left margin DF B MARGIN: DF leading edge margin DF C MARGIN: DF right margin DF D MARGIN: DF trailing edge margin Press the print key. The new setting is stored. Press the print key to make a test copy.
Press the interrupt key. Change the setting. Increasing the value using the Up key makes the margin wider. Decreasing the value using the Down key makes the margin narrower. Setting range (default) DF left margin: 0 - +20 (2) DF leading edge margin: 6 - +20 (6) DF right margin: 0 - +20 (2) DF trailing edge margin: 0 - +20 (6) Changing the value by 1 moves the margin by 0.5 mm for all.
No
3-3-101 3-3-99
2AD
Yes
End
Figure 3-3-117
3-3-100 3-3-102
2AD
One-way drum
Figure 3-3-118 Detaching and refitting the upper and lower deck separation rollers
One-way drum
Figure 3-3-119 Installing the one-way drum Be sure to orient the one-way drum as shown in the above diagram.
3-3-101 3-3-103
2AD ( 2 ) Detaching and refitting the deck paper conveying unit assembly <Procedure> 1. Open the large paper deck. 2. Open the deck right cover and remove the deck rear cover. 3. Remove the spring and four screws holding the deck paper conveying motor bracket and then the bracket. 4. Remove the two screws holding the deck paper conveying unit assembly and then the assembly.
Spring
Screws
Deck paper feed roller 2 Deck paper conveying roller Deck paper feed roller 1
Screws
Figure 3-3-120 Detaching and refitting the deck paper conveying unit assembly
3-3-102 3-3-104
2AD ( 3 ) Detaching and refitting deck paper feed roller 1 Clean or replace deck paper feed roller 1 as follows. <Procedure> 1. Remove the stop ring. 2. While pressing the roller down, pull out the shaft. 3. Take deck paper feed roller 1 out and clean or replace. 4. Refit all removed parts.
Shaft
Figure 3-3-121 Detaching and refitting deck paper feed roller 1 Use the above procedure to detach and refit deck paper feed roller 2 and the paper conveying roller.
3-3-103 3-3-105
2AD ( 4 ) Adjusting the position of the center adjuster (center line alignment) Perform the following adjustment if the center lines of the original and copy image are misaligned. <Procedure>
Start Retighten the two screws securing the center adjuster and close the large paper deck.
Are the center lines of the original and copy image misaligned? No Loosen the six screws securing the deck front cover. Adjust the position of the deck front cover such that the surface becomes flush with other covers on the machine front and retighten the screws. End
Yes
Loosen the two screws securing the center adjuster and adjust the position of the adjuster. For copy example 1, move it toward the machine rear (a). For copy example 2, move it toward the machine front (f).
Original
Copy example 1
Copy example 2
Figure 3-3-122
Center adjuster
Screws
3-3-104 3-3-106
2AD
1-1-23
2AD
3-4-1
2AD
MAIN IC10
ENGINE
3-4-2
2AD
3-4-3
2AD
1-1-25
2AD
3-5-1 Self-diagnosis
(1) Self-diagnostic function This unit is equipped with a self-diagnostic function. When a problem is detected, copying is disabled and the problem displayed as a code consisting of "C" followed by a number between 001 and 924, indicating the nature of the problem. A message is also displayed requesting the user to call for service. After removing the problem, the self-diagnostic function can be reset by turning safety switches 1, 2 or 3 off and back on.
012345678901234 C241
3-5-1
2AD Self diagnostic codes Remarks Code Contents Causes Defective memory copy PCB 1. Check procedures/ corrective measures Replace memory copy PCB 1 and check for correct operation. Replace memory copy PCB 2 and check for correct operation. Replace the main PCB and check for correct operation. Turn safety switch 1 off and back on and run maintenance item U020 to set the contents of the backup memory data again. If the C011 is displayed after re-setting the backup memory contents, replace the backup RAM. Check the connection of connectors CN6 on the main PCB and CN6 on the operation unit main PCB, and the continuity across the connector terminals. Repair or replace if necessary. Replace the main PCB or operation unit main PCB and check for correct operation.
C001 Memory copy PCB 1 communication problem Problems with data from memory copy PCB 1.
C003 Memory copy PCB 2 prob- Defective lem memory copy Problems with data from PCB 2. memory copy PCB 2. C010 RAM/ROM problem Read and write data does not match. C011 Backup memory data problem Data in the specified area of the backup memory does not match the specified values. Defective main PCB. Problem with the backup memory data.
C021 Operation unit main PCB communication problem There is no reply after 20 retries at communication.
3-5-2
2AD Remarks Code Contents Causes Defective engine ROM IC. Defective main PCB. Check procedures/ corrective measures Replace the engine ROM IC on the main PCB and check for correct operation. Replace the main PCB and check for correct operation. Check the connection of connectors CN5 on the main PCB and CN8 on the scanner control PCB, and the continuity across the connector terminals. Repair or replace if necessary. Replace the main PCB or scanner control PCB and check for correct operation. Check the connection of connector CN4 on the main PCB and the connector on the printer board. Repair or replace if necessary. Replace the main PCB or printer board and check for correct operation.
C022 Communication problem between the engine PCB and main PCB There is no reply after 20 retries at communication.
C023 Scanner control PCB Poor contact of communication problem the connector There is no reply after 5 re- terminals. tries at communication.
Defective main PCB or scanner control PCB. C024* Printer board communica- Poor contact of tion problem the connector There is no reply after 20 terminals. retries at communication. Defective main PCB or printer board.
3-5-3
2AD Remarks Code Contents Causes Poor contact of the connector terminals. Check procedures/ corrective measures Check the connection of connector CN2 on the main PCB and the connector on memory copy PCB 1. Repair or replace if necessary. Replace the main PCB or memory copy PCB 1 and check for correct operation. Check the connection of connector CN17 on the engine PCB and the connector CN9 on the deck main PCB, and the continuity across the connector terminals. Repair or replace if necessary. Replace the engine PCB and check for correct operation. Replace the main PCB and check for correct operation. Replace the deck main PCB and check for correct operation. Check the connection of connectors CN21 on the engine PCB and CN2 on the finisher main PCB, and the continuity across the connector terminals. Repair or replace if necessary. Replace the engine PCB and check for correct operation. Replace the main PCB and check for correct operation. Replace the finisher main PCB and check for correct operation.
C026 Memory copy PCB 1 communication problem There is no reply after five retries at transmitting. There is no reply after five retries at receiving.
Defective main PCB or memory copy PCB 1. Poor contact of the connector terminals.
C032 Large paper deck communication problem Communication errors from the communication microcomputer (IC7) on the main PCB: No communication: there is no replay after 3 retries. Abnormal communication: a communication error (parity or checksum error) is detected five times in succession.
Defective engine PCB. Defective main PCB. Defective deck main PCB. Poor contact of the connector terminals.
C034* Finisher communication problem Communication errors from the communication microcomputer (IC7) on the main PCB: No communication: there is no reply after 3 retries. Abnormal communication: a communication error (parity or checksum error) is detected five times in succession.
Defective engine PCB. Defective main PCB. Defective finisher main PCB.
3-5-4
C036 Memory copy PCB 2 communication problem There is no reply after five retries at transmitting. There is no reply after five retries at receiving. C037 Communication microcomputer problem A problem is detected with the communication microcomputer (IC7) on the main PCB. C104 Optical system problem After AGC, correct input is not obtained at CCD.
Poor contact of Check the connection of connector CN3 on the main PCB the connector and the connector on memory terminals. copy PCB 2. Repair or replace if necessary. Defective main PCB or memory copy PCB 2. Defective main PCB. Insufficient exposure lamp luminosity. Replace the main PCB or memory copy PCB 2 and check for correct operation. Replace the main PCB and check for correct operation. Replace the exposure lamp or inverter PCB.
Defective scan- Replace the scanner control PCB. ner control PCB. Incorrect shading position. Adjust the position of the contact glass (shading plate). If the problem still occurs, replace the scanner home position switch. Replace the ISU. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Replace the drive motor.
CCD PCB output problem. C200 Drive motor problem DM LOCK signal remains high for 1 s, 1 s after the drive motor has turned on. Poor contact of the drive motor connector terminals. Defective drive motor rotation control circuit. Defective drive transmission system.
Check if the rollers and gears rotate smoothly. If not, grease the bushings and gears. Check for broken gears and replace if any.
3-5-5
2AD Remarks Code Contents Causes Poor contact of the paper conveying motor connector terminals. Check procedures/ corrective measures Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
C210 Paper conveying motor problem PCM LOCK signal remains high for 1 s, 1 s after the conveying motor has turned on.
Defective paper Replace the paper conveying conveying mo- motor. tor rotation control circuit. Defective drive transmission system. Check if the rollers and gears rotate smoothly. If not, grease the bushings and gears. Check for broken gears and replace if any.
C220 Side registration motor problem A problem where the side registration home position switch does not turn off after the side registration motor has turned 30 steps or the switch does not turn on after the motor has turned 265 steps is detected twice in succession. (The first time, the copier indicates that the duplex unit is not inserted correctly, requesting the user to open and reinsert the duplex unit. After the second detection, the copier enters partial operation control.)
Defective side Check for continuity across registration mo- the coil. If none, replace the tor. side registration motor. Defective side registration home position switch. Check if CN9-12 on the engine PCB goes high when the side registration home position switch is on and goes low when the switch is off. If not, replace the switch. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Check if the side registration guides operate smoothly. If not, repair.
Poor contact of the connector terminals. Malfunction of the side registration guides.
3-5-6
2AD Remarks Code Contents Causes Check procedures/ corrective measures Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Replace the paper feed motor.
C230 Paper feed motor problem Poor contact of PFM LOCK signal remains the connector high for 1 s, 1 s after the terminals. paper feed motor has turned on. Defective paper feed motor rotation control circuit. Defective drive transmission system.
Check if the rollers and gears rotate smoothly. If not, grease the bushings and gears. Check for broken gears and replace if any. Replace the upper lift motor.
C241 Upper lift motor problem When the drawer is inserted, the upper lift limit switch does not turn on within 4 to 5 s of the upper lift motor turning on. During copying, the upper lift limit switch does not turn on within 200 ms of the upper lift motor turning on.
Defective upper Check for continuity across the coil. If none, replace the lift motor. upper lift motor. Poor contact of the upper lift motor connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
Defective upper Check if CN15-3 on the enlift limit switch. gine PCB goes low when the upper lift limit switch is turned on. If not, replace the upper lift limit switch. Poor contact of the upper lift limit switch connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
3-5-7
2AD Remarks Code Contents Causes Broken gears or couplings of the lower lift motor Check procedures/ corrective measures Replace the lower lift motor.
C242 Lower lift motor problem When the drawer is inserted, the lower lift limit switch does not turn on within 4 to 5 s of the lower lift motor turning on. During copying, the lower lift limit switch does not turn on within 200 ms of the lower lift motor turning on.
Defective lower Check for continuity across the coil. If none, replace the lift motor. lower lift motor. Poor contact of the lower lift motor connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
Defective lower Check if CN15-4 on the enlift limit switch. gine PCB goes low when the lower lift limit switch is turned on. If not, replace the upper lift limit switch. Poor contact of the lower lift limit switch connector terminals. C310 Scanner carriage problem The home position is not correct when the power is turned on or at the start of copying using the bypass table. Poor contact of the connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Check the connection of connector CN4 on the scanner control PCB and the continuity across the connector terminals. Repair or replace if necessary.
Defective scan- Replace the scanner home ner home posi- position switch. tion switch. Defective main PCB, scanner control PCB or scanner motor PCB. Replace the main PCB, scanner control PCB or scanner motor PCB and check for correct operation.
Defective scan- Replace the scanner motor. ner motor. C332 Scanner watchdog problem The main routine does not run within 8.192 ms of the main switch being turned on. Defective scan- Replace the scanner control PCB and check for correct opner control eration. PCB.
3-5-8
C340 Original detection position problem The original size detection microcomputer (IC29) in the scanner control PCB cannot store initial data correctly.
Poor contact of Check the connection of conthe connectors. nector CN7 on the scanner control PCB and the continuity across the connector terminals. Repair or replace if necessary. Defective origi- Replace the original size sennal size sensor. sor. Defective main PCB or scanner control PCB. Replace the main PCB or scanner control PCB and check for correct operation. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Replace the LSU. Check if 24 V DC is supplied to CN6-5 on the engine PCB. If not, replace the power source PCB. Check if 24 V DC is output from CN7-1 on the engine PCB. If not, replace the engine PCB. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Replace the LSU. Check if 24 V DC is supplied to CN6-5 on the engine PCB. If not, replace the power source PCB. Check if 24 V DC is output from CN7-1 on the engine PCB. If not, replace the engine PCB.
C400 Polygon motor synchronization problem The polygon motor does not reach the stable speed within 9 s of the polygon motor remote signal turning on.
Poor contact of the polygon motor connector terminals. Defective polygon motor. Defective power source PCB. Defective engine PCB.
C401 Polygon motor steadystate problem The polygon motor rotation is not stable for 600 ms after the polygon motor rotation has been stabilized.
Poor contact of the polygon motor connector terminals. Defective polygon motor. Defective power source PCB. Defective engine PCB.
3-5-9
2AD Remarks Code Contents Causes Defective laser diode. Defective polygon motor. Defective main PCB. C510 Main charger problem MC ALM signal is detected continuously for 400 ms when MC REM signal is turned on. C511 Transfer/separation highvoltage problem STALM signal is detected continuously for 400 ms when TC/SC REM signal is turned on. C610 Broken fixing unit thermistor wire The fixing temperature does not increase for 20 s after the fixing heaters have been turned on for warming up. The fixing temperature remains below 50C/122F for 10 s continuously after the fixing heaters have been turned on during stabilization. Defective highvoltage transformer PCB. Check procedures/ corrective measures Replace the LSU. Replace the LSU. Replace the main PCB. Replace the high-voltage transformer PCB.
C420 BD steady-state problem The VTC detects a BD error for 600 ms after the polygon motor rotation has been stabilized.
Leakage during Check and clean the main main charging. charger assembly. Defective highvoltage transformer PCB. Replace the high-voltage transformer PCB.
Leakage during Check and clean the transfer transfer/sepacharger assembly. ration charging. Poor contact of the fixing unit thermistor connector terminals. Broken fixing unit thermistor wire. Check the connection of connector CN3-B8 on the engine PCB and the continuity across the connector terminals. Repair or replace if necessary. Measure the resistance. If it is infinite, replace the fixing unit thermistor.
Fixing unit ther- Check and reinstall if necesmistor installed sary. incorrectly. Fixing unit ther- Check for continuity. If none, mostat 1 or 2 replace the fixing unit thermotriggered. stat 1 or 2. Fixing unit heater M or S installed incorrectly. Check and reinstall if necessary.
Broken fixing Check for continuity. If none, unit heater M or replace the fixing unit heater S wire. M or S.
3-5-10
2AD Remarks Code Contents Causes Poor contact of the fixing unit thermistor connector terminals. Broken fixing unit thermistor wire. Check procedures/ corrective measures Check the connection of connector CN3-B8 on the engine PCB and the continuity across the connector terminals. Repair or replace if necessary. Measure the resistance. If it is infinite, replace the fixing unit thermistor.
C620 Abnormally low fixing temperature The fixing temperature remains below 120C/248F for 10 s.
Fixing unit ther- Check and reinstall if necesmistor installed sary. incorrectly. Fixing unit ther- Check for continuity. If none, mostat 1 or 2 replace the fixing unit thermotriggered. stat 1 or 2. Fixing unit heater M or S installed incorrectly. Check and reinstall if necessary.
Broken fixing Check for continuity. If none, unit heater M or replace the fixing unit heater S wire. M or S. C630 Abnormally high fixing temperature The fixing temperature exceeds 220C/428F for 10 s. The fixing unit high temperature detection circuit on the engine PCB detects an abnormally high temperature. Shorted fixing unit thermistor. Measure the resistance. If it is infinite, replace the fixing unit thermistor.
Broken fixing Replace the power source unit heater con- PCB. trol circuit on the power source PCB.
3-5-11
2AD Remarks Code Contents Causes Poor contact of the connector terminals. Check procedures/ corrective measures Check the connection of connectors CN10-5 on the main PCB and CN4-3 on the power source PCB, and the continuity across the connector terminals. Repair or replace if necessary. Check if the zero-crossing signal is output from CN4-3 on the power source PCB. If not, replace the power source PCB. Replace the main PCB if C640 is detected while CN4-3 on the power source PCB outputs the zero-crossing signal. Replace the toner sensor. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Replace the developer.
C640 Zero-crossing signal problem The main PCB does not detect the zero-crossing signal (Z CROSS SIG) for the time specified below. At power-on: 3 s Others: 5 s
C710 Toner sensor problem The sensor output voltage is outside the range of 0.5 to 4.5 V during copying or in maintenance item U130. The toner sensor control voltage cannot be set within the range in maintenance item U130.
Defective toner sensor. Poor contact of the toner sensor connector terminals. Developer problem.
3-5-12
2AD Remarks Code Contents Causes Poor contact of the humidity sensor PCB connector terminals. Check procedures/ corrective measures Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
C730 Broken external temperature thermistor wire The input voltage is above 4.5 V (230 bits).
Defective exter- Replace the humidity sensor nal temperature PCB. thermistor. C731 Short-circuited external temperature thermistor The input voltage is below 0.5 V (250 bits). Poor contact of the humidity sensor PCB connector terminals. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
Defective exter- Replace the humidity sensor nal temperature PCB. thermistor. C740 Toner hopper problem The toner hopper lockup sensor does not turn off after the toner recycle motor has rotated for at least 1 minute. Toner main hopper lockup. Remove the recycled toner in the toner main hopper if it locks up.
Defective toner Replace the toner hopper hopper lockup lockup sensor. sensor. Poor contact of the toner hopper lockup sensor connector terminals. Reinsert the connectors. Also check for continuity within the cable. If none, remedy or replace the cable.
Defective toner Check for continuity across recycle motor. the coils. If none, replace the recycle motor. Poor contact of the toner recycle motor connector terminals. Reinsert the connectors. Also check for continuity within the cable. If none, remedy or replace the cable.
3-5-13
2AD Remarks Code Contents Causes The paper conveying motor connector makes poor contact. The paper conveying motor malfunctions. Defective finisher main PCB. C803* Finisher paper conveying belt problem An on-to-off or off-to-on state change of the paper conveying belt home position sensor is not detected within 2 s of the paper conveying belt clutch turning on. The paper conveying belt is out of phase. The paper conveying belt clutch malfunctions. The paper conveying belt home position sensor malfunctions. The paper conveying belt home position sensor connector makes poor contact. The internal tray is incorrectly inserted. Check procedures/ corrective measures Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Replace the paper conveying motor and check for correct operation. Replace the finisher main PCB and check for correct operation. Adjust the paper conveying belt so that it is in phase and check for correct operation. Replace the paper conveying belt clutch and check for correct operation. Replace the paper conveying belt home position sensor and check for correct operation.
C801* Finisher paper conveying motor problem The paper conveying motor lockup signal is detected for 0.5 s or longer.
Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
Check whether the internal tray unit or front cover catches are damaged.
3-5-14
2AD Remarks Code Contents Causes The tray elevation motor connector makes poor contact. The tray elevation motor malfunctions. Defective finisher main PCB. C817* Finisher front jogger motor problem While the front jogger is not detected in the home position, the front jogger home position sensor does not detect the jogger within 1.5 s of the start of front jogger motor clockwise rotation. After the front jogger is detected in the home position, the front jogger home position sensor still detects the jogger within 0.5 s of the start of front jogger motor counterclockwise rotation. The front jogger motor connector makes poor contact. The front jogger motor malfunctions. The front jogger motor home position sensor connector makes poor contact. The front jogger motor home position sensor malfunctions. Defective finisher main PCB. Check procedures/ corrective measures Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Replace the tray elevation motor and check for correct operation. Replace the finisher main PCB and check for correct operation. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Replace the front jogger motor and check for correct operation. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
C814* Finisher tray elevation motor problem The sort tray is not detected in the home position within 30 s of the start of the tray elevation motor rotation.
Replace the front jogger home position sensor and check for correct operation.
Replace the finisher main PCB and check for correct operation.
3-5-15
2AD Remarks Code Contents Causes The rear jogger motor connector makes poor contact. The rear jogger motor malfunctions. The rear jogger motor home position sensor connector makes poor contact. The rear jogger motor home position sensor malfunctions. Defective finisher main PCB. Check procedures/ corrective measures Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Replace the rear jogger motor and check for correct operation. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
C818* Finisher rear jogger motor problem While the rear jogger is not detected in the home position, the rear jogger home position sensor does not detect the jogger within 1.5 s of the start of rear jogger motor clockwise rotation. After the rear jogger is detected in the home position, the rear jogger home position sensor still detects the jogger within 0.5 s of the start of rear jogger motor counterclockwise rotation.
Replace the rear jogger home position sensor and check for correct operation.
Replace the finisher main PCB and check for correct operation.
3-5-16
2AD Remarks Code Contents Causes The front stapler connector makes poor contact. The front stapler malfunctions. a) The front stapler is blocked with a staple. b) The front stapler is broken. Defective finisher main PCB. The rear stapler connector makes poor contact. The rear stapler malfunctions. a) The rear stapler is blocked with a staple. b) The rear stapler is broken. Check procedures/ corrective measures Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
C821* Finisher front stapler problem The front stapler home position sensor does not change state from non-detection to detection within 0.2 s of the start of front stapler motor counterclockwise (forward) rotation. During initialization, the front stapler home position sensor does not change state from non-detection to detection within 0.6 s of the start of front stapler motor clockwise (reverse) rotation. C822* Finisher rear stapler problem The rear stapler home position sensor does not change state from non-detection to detection within 0.2 s of the start of rear stapler motor counterclockwise (forward) rotation. During initialization, the rear stapler home position sensor does not change state from non-detection to detection within 0.6 s of the start of rear stapler motor clockwise (reverse) rotation.
a) Remove the front stapler cartridge, and check the cartridge and the stapling section of the stapler. b) Replace the front stapler and check for correct operation. Replace the finisher main PCB and check for correct operation. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
a) Remove the rear stapler cartridge, and check the cartridge and the stapling section of the stapler. b) Replace the rear stapler and check for correct operation. Replace the finisher main PCB and check for correct operation.
3-5-17
2AD Remarks Code Contents Causes The deck paper conveying motor connector makes poor contact. Check procedures/ corrective measures Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
C920 Deck paper conveying motor problem No pulse is input within 500 ms of the start-up. No pulse is input within 100 ms of the previous pulse input.
Defective deck Replace the deck paper conpaper convey- veying motor PCB and check ing motor PCB. for correct operation. The deck paper Check the gears and remedy if conveying mo- necessary. tor does not rotate correctly (the motor is overloaded).
C921 Paper deck motor 1 problem No pulse is input within 20 ms of the start-up. No pulse is input within 400 ms of the previous pulse input.
Paper deck motor 1 connector makes poor contact. Paper deck motor 1 does not rotate correctly (the motor is overloaded).
Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Check the gears and remedy if necessary.
3-5-18
2AD Remarks Code Contents Causes Paper deck motor 2 connector makes poor contact. Paper deck motor 2 does not rotate correctly (the motor is overloaded). Upper limit switch 1 connector makes poor contact. Deck level switch 1 connector makes poor contact. Upper limit switch 2 connector makes poor contact. Deck level switch 2 connector makes poor contact. Check procedures/ corrective measures Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Check the gears and remedy if necessary.
C922 Paper deck motor 2 problem No pulse is input within 20 ms of the start-up. No pulse is input within 400 ms of the previous pulse input.
C923 Right lift position problem While the paper deck motor is driving, lift upper limit switch 1 detects the right lift reaching the upper limit.
Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
C924 Left lift position problem While the paper deck motor is driving, lift upper limit switch 2 detects the left lift reaching the upper limit.
3-5-19
2AD-1 2AD
1-1-27
2AD (7) A paper jam in the paper feed section is indicated during copying (multiple sheets in paper feed section). ....................... (8) A paper jam in the paper feed section is indicated during copying (multiple sheets in copier vertical conveying section). .................................................................... (9) A paper jam in the paper feed section is indicated during copying (multiple sheets before registration section). ............... (10) A paper jam in the paper conveying section is indicated during copying (jam in registration/transfer section). ................. (11) A paper jam in the fixing section is indicated during copying (jam in fixing section). .................................................. (12) A paper jam in the eject section is indicated during copying (jam in eject section). ................................................... (13) A paper jam in the eject section is indicated during copying (jam in switchback eject section). ................................ SRDF .............................................................................................. (1) An original jams when the main switch is turned on. ................. (2) An original jams during continuous copying of multiple originals. ....................................................................... (3) An original jams in the SRDF during copying (a jam in the original feed/conveying section). .......................... (4) An original jams in the SRDF during copying (a jam in the original switchback section). ................................. (5) Original jams frequently. ............................................................ Feedshift and duplex sections ........................................................ (1) A paper jam in the feedshift section is indicated during copying (jam in feedshift section). ............................................. (2) A paper jam in the duplex section is indicated during copying (jam in duplex conveying section). ............................... (3) A paper jam in the duplex section is indicated during copying (jam in duplex stock section). ....................................... Large paper deck ............................................................................ (1) A paper jam in the large paper deck is indicated during copying (paper failing to reach PPS0 in large paper deck horizontal paper path). .............................................................. (2) A paper jam in the large paper deck is indicated during copying (paper failing to reach PPS1 in large paper deck horizontal paper path). .............................................................. (3) A paper jam in the large paper deck is indicated during copying (paper failing to reach PPS2 in large paper deck horizontal paper path). .............................................................. 3-6-3 PCB terminal voltages ...................................................................... (1) Power source PCB .................................................................... (2) Engine PCB ............................................................................... (3) Main PCB .................................................................................. (4) Memory copy PCB .................................................................... (5) Scanner control PCB ................................................................. (6) Scanner motor PCB .................................................................. (7) CCD PCB .................................................................................. (8) DF driver PCB ...........................................................................
3-6-20
3-6-20 3-6-20 3-6-21 3-6-21 3-6-21 3-6-22 3-6-23 3-6-23 3-6-23 3-6-24 3-6-25 3-6-25 3-6-26 3-6-26 3-6-26 3-6-27 3-6-28
3-6-28
3-6-29
3-6-30 3-6-31 3-6-31 3-6-34 3-6-45 3-6-54 3-6-57 3-6-61 3-6-63 3-6-65
1-1-28
2AD (9) Operation unit main PCB ........................................................... (10) Deck main PCB ......................................................................... 3-6-4 Electrical problems ............................................................................ Copier ............................................................................................. (1) The machine does not operate when the main switch is turned on. .................................................................................. (2) The drive motor does not operate (C200). ................................ (3) The scanner motor does not operate. ....................................... (4) The upper lift motor does not operate. ...................................... (5) The lower lift motor does not operate. ....................................... (6) The toner feed motor does not operate. .................................... (7) The paper conveying section fan motor does not operate. ....... (8) Cooling fan motor 1 does not operate at all or does not turn at full speed. .................................................... (9) Cooling fan motor 2 does not operate at all or does not turn at full speed. .................................................... (10) Paper feed motor does not operate (C230). .............................. (11) The paper conveying motor does not operate (C210). .............. (12) The toner recycle motor does not operate. ............................... (13) The charger cleaning motor does not operate. ......................... (14) The image formation unit fan motor does not operate. ............. (15) The upper paper feed clutch does not operate. ........................ (16) The lower paper feed clutch does not operate. ......................... (17) Feed clutch 1 does not operate. ................................................ (18) Feed clutch 2 does not operate. ................................................ (19) Feed clutch 3 does not operate. ................................................ (20) Feed clutch 4 does not operate. ................................................ (21) Feed clutch 5 does not operate. ................................................ (22) The registration clutch does not operate. .................................. (23) The bypass paper feed clutch does not operate. ...................... (24) The eject speed switching clutch does not operate. .................. (25) The bypass solenoid does not operate. .................................... (26) The cleaning lamp does not turn on. ......................................... (27) The exposure lamp does not turn on. ........................................ (28) The exposure lamp does not turn off. ........................................ (29) Fixing heater M or S does not turn on (C620). .......................... (30) Fixing heater M or S does not turn off (fixing unit thermostat 1/2 triggered; C620). .............................. (31) Main charging is not performed (C510). .................................... (32) Transfer charging is not performed (C511). .............................. (33) Separation charging is not performed (C511). .......................... (34) No developing bias is output. .................................................... (35) The original size is not detected. ............................................... (36) The original size is not detected correctly. ................................ (37) The touch panel keys do not work. ............................................ (38) The message requesting paper to be loaded is shown when paper is present in the upper drawer. ................... (39) The message requesting paper to be loaded is shown when paper is present in the lower drawer. ............................... (40) The message requesting paper to be loaded is shown when paper is present on the bypass table. .............................. 3-6-68 3-6-71 3-6-74 3-6-74 3-6-74 3-6-74 3-6-75 3-6-75 3-6-75 3-6-76 3-6-76 3-6-76 3-6-76 3-6-77 3-6-77 3-6-77 3-6-78 3-6-78 3-6-78 3-6-79 3-6-79 3-6-79 3-6-79 3-6-80 3-6-80 3-6-80 3-6-80 3-6-81 3-6-81 3-6-81 3-6-81 3-6-82 3-6-82 3-6-82 3-6-82 3-6-83 3-6-83 3-6-83 3-6-84 3-6-84 3-6-84 3-6-84 3-6-85 3-6-85
1-1-29
2AD (41) The size of paper in the upper drawer is not displayed correctly. .................................................................... 3-6-85 (42) The size of paper in the lower drawer is not displayed correctly. .................................................................... 3-6-86 (43) A paper jam in the paper feed, paper conveying or fixing section is indicated on the touch panel immediately after the main switch is turned on. ..................................................... 3-6-87 (44) The message requesting covers to be closed is displayed when the front, left and right covers are closed......................... 3-6-88 (45) Others........................................................................................ 3-6-88 SRDF .............................................................................................. 3-6-89 (1) The original feed motor does not operate. ................................ 3-6-89 (2) The original conveying motor does not operate. ....................... 3-6-89 (3) The original feed solenoid does not operate. ............................ 3-6-89 (4) The switchback feedshift solenoid does not operate. ................ 3-6-90 (5) The eject feedshift solenoid does not operate........................... 3-6-90 (6) The switchback pressure solenoid does not operate. ............... 3-6-90 (7) The original feed clutch does not operate. ................................ 3-6-91 (8) A message indicating cover open is displayed when the SRDF is closed correctly. .................................................... 3-6-91 (9) An original jams when the main switch is turned on.................. 3-6-91 Feedshift and duplex sections ........................................................ 3-6-93 (1) The side registration motor does not rotate (C220). .................. 3-6-93 (2) The feedshift solenoid does not operate. .................................. 3-6-93 (3) The duplex forward solenoid does not operate. ........................ 3-6-93 (4) The switchback feedshift solenoid does not operate. ................ 3-6-94 (5) The duplex paper tapping solenoid does not operate. .............. 3-6-94 (6) The message requesting covers to be closed is displayed when the left cover is closed. .................................................... 3-6-94 (7) Others........................................................................................ 3-6-94 Large paper deck ............................................................................ 3-6-95 (1) The large paper deck does not operate when the print key is pressed. ..................................................................................... 3-6-95 (2) The deck paper conveying motor does not operate (C920). ..... 3-6-95 (3) Paper deck motor 1 does not operate (C921). .......................... 3-6-95 (4) Paper deck motor 2 does not operate (C922). .......................... 3-6-96 (5) Paper feed clutch 1 does not operate. ...................................... 3-6-96 (6) Paper feed clutch 2 does not operate. ...................................... 3-6-96 (7) The paper conveying clutch dose not operate. ......................... 3-6-97 3-6-5 Mechanical problems ........................................................................ 3-6-98 Copier ............................................................................................. 3-6-98 (1) No primary paper feed............................................................... 3-6-98 (2) No secondary paper feed. ......................................................... 3-6-98 (3) Skewed paper feed. .................................................................. 3-6-98 (4) The scanner does not travel. ..................................................... 3-6-99 (5) Multiple sheets of paper are fed at one time. ............................ 3-6-99 (6) Paper jams. ............................................................................... 3-6-99 (7) Toner drops on the paper conveying path. ................................ 3-6-99 (8) Abnormal noise is heard. ......................................................... 3-6-100
1-1-30
2AD SRDF ............................................................................................ (1) No primary original feed. ......................................................... (2) No secondary original feed. ..................................................... (3) Originals jam. .......................................................................... Feedshift and duplex sections ...................................................... (1) No refeed. ................................................................................ (2) Paper is refed askew. .............................................................. (3) Paper jams. ............................................................................. (4) Abnormal noise is heard. ......................................................... Large paper deck .......................................................................... (1) No primary paper feed. ............................................................ (2) Paper is fed askew. ................................................................. (3) Multiple sheets of paper are fed at one time. .......................... (4) Paper jams. ............................................................................. (5) Abnormal noise is heard. ......................................................... 3-6-101 3-6-101 3-6-101 3-6-101 3-6-102 3-6-102 3-6-102 3-6-102 3-6-102 3-6-103 3-6-103 3-6-103 3-6-103 3-6-103 3-6-104
1-1-31
2AD
See page 3-6-6 (8) One side of the copy image is darker than the other.
See page 3-6-7 (11) The leading edge of the image is consistently misaligned with the original.
See page 3-6-8 (12) The leading edge of the image is sporadically misaligned with the original.
3-6-1
2AD (13) Paper creases. (14) Offset occurs. (15) Image is partly missing.
See page 3-6-11 (18) Image center does not align with the original center.
See page 3-6-12 (21) There is a regular error between the centers of the original and copy image when the SRDF is used.
See page 3-6-13 (22) There is a regular error between the leading edges of the original and copy image when the SRDF is used.
See page 3-6-13 (23) When the duplex unit is used, the center of the original image and that of the copy image do not align.
See page 3-6-14 (24) When the large paper deck is used, the center of the original image and that of the copy image do not align.
3-6-2
2AD-1 2AD
3-6-2-1 3-6-3
2AD-1 2AD
3-6-4
Causes 1. No transfer charging. A. Broken transfer charger wire. B. The connector terminals of the high-voltage transformer PCB make poor contact. C. Defective main PCB.
Check procedures/corrective measures Replace the wire. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Check if CN1-84 on the main PCB goes low when maintenance item U101 is run. If not, replace the main PCB. Check if CN5-B7 on the engine PCB goes low when CN1-84 on the main PCB is held low while maintenance item U101 is run. If not, replace the engine PCB. Check if transfer charging takes place when CN1-7 on the high-voltage transformer PCB goes low while maintenance item U101 is run. If not, replace the high-voltage transformer PCB.
3-6-3 3-6-5
2AD-1 2AD (2) No image appears (entirely black). Causes 1. No main charging. 2. Exposure lamp fails to light.
Causes 1. No main charging. A. Broken main charger wire. B. Leaking main charger housing. C. The connector terminals of the high-voltage transformer PCB make poor contact. D. Defective main PCB.
2. Exposure lamp fails to light. A. The connector terminals of the exposure lamp make poor contact. B. Defective inverter PCB.
3-6-4 3-6-6
2AD (3) Image is too light. Causes 1. Insufficient toner. 2. Deteriorated developer. 3. Dirty or deteriorated drum.
Check procedures/corrective measures If the display shows the message requesting toner replenishment, replace the cartridge. Check the number of copies made with the current developer. If it has reached the specified limit, replace the developer. Clean the drum or, if the maintenance level has been reached, replace the drum (see page 3-3-43).
Check procedures/corrective measures Check the number of copies made with the current developer. If it has reached the specified limit, replace the developer.
3-6-5 3-6-7
2AD (5) A white line appears longitudinally. Causes 1. Dirty or flawed transfer charger wire. 2. Foreign matter in the developing section. 3. Flawed drum. 4. Dirty shading plate.
Causes 1. Dirty or flawed transfer charger wire. 2. Foreign matter in the developing section. 3. Flawed drum. 4. Dirty shading plate.
Check procedures/corrective measures Clean the transfer charger wire or, if it is flawed, replace it. Check if the magnetic brush is formed uniformly. If not, replace the developer. Replace the drum (see page 3-3-43). Clean the shading plate.
Causes 1. Dirty contact glass. 2. Dirty or flawed drum. 3. Deformed or worn cleaning blade. 4. Dirty scanner mirror.
Causes 1. Dirty contact glass. 2. Dirty or flawed drum. 3. Deformed or worn cleaning blade. 4. Dirty scanner mirror.
Check procedures/corrective measures Clean the contact glass. Clean the drum or, if it is flawed, replace it (see page 3-3-43). Replace the cleaning blade (see page 3-3-57). Clean the scanner mirror.
3-6-6 3-6-8
2AD (7) A black line appears laterally. Causes 1. Flawed drum. 2. Dirty developing section. 3. Leaking main charger housing.
Causes 1. Flawed drum. 2. Dirty developing section. 3. Leaking main charger housing.
Check procedures/corrective measures Replace the drum (see page 3-3-43). Clean any part contaminated with toner or carrier in the developing section. Clean the main charger wire, grid and shield.
(8) One side of the copy image is darker than the other.
Check procedures/corrective measures Clean the wire or, if it is extremely dirty, replace it. Check if the exposure lamp light is distributed evenly. If not, replace the exposure lamp (see page 3-3-23).
3-6-7 3-6-9
2AD (9) Black dots appear on the image. Causes 1. Dirty or flawed drum. 2. Deformed or worn cleaning blade.
Check procedures/corrective measures Clean the drum or, if it is flawed, replace it (see page 3-3-43). Replace the cleaning blade (see page 3-3-57).
Causes 1. Scanner moves erratically. 2. Deformed press roller. 3. Paper conveying section drive problem.
Causes 1. Scanner moves erratically. 2. Deformed press roller. 3. Paper conveying section drive problem.
Check procedures/corrective measures Check if there is any foreign matter on the front and rear scanner rails. If any, remove it. Replace the press roller (see page 3-3-70). Check the gears and belts and, if necessary, grease them.
3-6-8 3-6-10
2AD (11) The leading edge of the image is consistently misaligned with the original. Causes 1. Misadjusted leading edge registration.
Check procedures/corrective measures Readjust the leading edge registration (see pages 3-3-18 and 37).
(12) The leading edge of the image is sporadically misaligned with the original.
Causes 1. Registration clutch, bypass paper feed clutch or upper or lower paper feed clutch installed or operating incorrectly.
Causes 1. Registration clutch, bypass paper feed clutch or upper or lower paper feed clutch installed or operating incorrectly.
Check procedures/corrective measures Check the installation position and operation of the registration clutch, bypass paper feed clutch and upper and lower paper feed clutches. If any of them operates incorrectly, replace it.
3-6-11 3-6-9
2AD (13) Paper creases. Causes 1. Paper curled. 2. Paper damp. 3. Defective pressure springs.
Check procedures/corrective measures Check the paper storage conditions. Check the paper storage conditions. Replace the pressure springs.
Check procedures/corrective measures Replace the cleaning blade (see page 3-3-57).
3-6-10 3-6-12
2AD (15) Image is partly missing. Causes 1. Paper damp. 2. Paper creased. 3. Drum condensation. 4. Flawed drum.
Check procedures/corrective measures Check the paper storage conditions. Replace the paper. Clean the drum (see page 3-3-48). Replace the drum (see page 3-3-43).
Check procedures/corrective measures Check if the paper meets specifications. Replace the pressure springs. Replace the press roller (see page 3-3-70).
3-6-11 3-6-13
2AD (17) Image is out of focus. Causes 1. Defective image scanning unit.
(18) Image center does not align with the original center.
Causes 1. Misadjusted image center line. 2. Misadjusted scanner center line. 3. Original placed incorrectly.
Causes 1. Misadjusted image center line. 2. Misadjusted scanner center line. 3. Original placed incorrectly.
Check procedures/corrective measures Readjust the image center line (see page 33-19). Readjust the scanner center line (see page 3-3-36). Place the original correctly.
3-6-12 3-6-14
2AD (19) Image is not square. Causes 1. Laser scanner unit positioned incorrectly. 2. Image scanning unit positioned incorrectly.
Causes 1. Laser scanner unit positioned incorrectly. 2. Image scanning unit positioned incorrectly.
Check procedures/corrective measures Adjust the installation position of the laser scanner unit (see page 3-3-31). Adjust the installation position of the image scanning unit (see page 3-3-33).
Causes 1. No developing bias output. A. Developing bias wire makes poor contact. B. Defective main PCB.
Check procedures/corrective measures Check the developing bias wire. If there are any problems, replace it. Check if CN1-85 on the main PCB goes low when maintenance item U030 is run. If not, replace the main PCB. Check if developing bias is output when there is no problem with the main PCB while maintenance item U030 is run. If not, replace the high-voltage transformer PCB.
3-6-13 3-6-15
2AD (21) There is a regular error between the centers of the original and copy image when the SRDF is used. Causes 1. Misadjusted DF center line.
Check procedures/corrective measures Readjust the DF center line (see page 3-3-96).
(22) There is a regular error between the leading edges of the original and copy image when the SRDF is used.
Check procedures/corrective measures Readjust the DF original scanning start position (see page 3-3-97).
3-6-16 3-6-14
2AD (23) When the duplex unit is used, the center of the original image and that of the copy image do not align. Causes 1. Side registration section installed incorrectly.
Check procedures/corrective measures Adjust the installation position of the side registration section (see page 3-3-86).
(24) When the large paper deck is used, the center of the original image and that of the copy image do not align.
Check procedures/corrective measures Adjust the installation position of the center adjuster (see page 3-3-104).
3-6-17 3-6-15
2AD-1 2AD
Check procedures/corrective measures Vacuum clean the paper powder from the upper registration cleaner assembly.
3-6-15-1 3-6-18
2AD-1 2AD
3-6-19
2AD
With 5 V DC present at CN13-5 on the engine PCB, check if CN13-4 on the engine PCB remains low when paper feed switch 1 is turned on and off. If it does, replace paper feed switch 1. With 5 V DC present at CN13-8 on the engine PCB, check if CN13-7 on the engine PCB remains low when paper feed switch 2 is turned on and off. If it does, replace paper feed switch 2. With 5 V DC present at CN1311 on the engine PCB, check if CN13-10 on the engine PCB remains low when paper feed switch 3 is turned on and off. If it does, replace paper feed switch 3. With 5 V DC present at CN13-2 on the engine PCB, check if CN13-1 on the engine PCB remains low when the feed switch is turned on and off. If it does, replace the feed switch. With 5 V DC present at CN8-B1 on the engine PCB, check if CN8-B2 on the engine PCB remains low when the registration switch is turned on and off. If it does, replace the registration switch.
3-6-16
2AD Problem (1) A paper jam in the paper feed, conveying or eject section is indicated as soon as the main switch is turned on. (2) A paper jam in the paper feed section is indicated during copying (no paper feed from copier upper drawer). Causes/check procedures Defective eject switch. Corrective measures With 5 V DC present at CN3B10 on the engine PCB, check if CN3-B9 on the engine PCB remains low when the eject switch is turned on and off. If it does, replace the eject switch.
Paper in the upper drawer is extremely curled. Check if the upper paper feed pulley, lower paper feed pulley or upper forwarding pulley of the upper drawer are deformed. Broken paper feed switch 2 actuator. Defective paper feed switch 2.
Change the paper. Check visually and replace any deformed pulleys.
Check visually and replace paper feed switch 1 if its actuator is broken. With 5 V DC present at CN13-8 on the engine PCB, check if CN13-7 on the engine PCB goes low when paper feed switch 2 is turned on. If not, replace paper feed switch 2. Check and repair if necessary. Check (see page 3-6-78).
Check if the upper paper feed clutch malfunctions. Electrical problem with the upper paper feed clutch.
3-6-17
2AD Problem (3) A paper jam in the paper feed section is indicated during copying (no paper feed from copier lower drawer). Causes/check procedures Paper in the lower drawer is extremely curled. Check if the upper paper feed pulley, lower paper feed pulley or upper forwarding pulley of the lower drawer are deformed. Broken paper feed switch 3 actuator. Defective paper feed switch 3. Corrective measures Change the paper. Check visually and replace any deformed pulleys.
Check visually and replace paper feed switch 3 if its actuator is broken. With 5 V DC present at CN1311 on the engine PCB, check if CN13-10 on the engine PCB goes low when paper feed switch 3 is turned on. If not, replace paper feed switch 3. Check and repair if necessary. Check (see page 3-6-79). Change the paper. Check visually and replace any deformed pulleys.
Check if the lower paper feed clutch malfunctions. Electrical problem with the lower paper feed clutch. (4) A paper jam in the paper feed section is indicated during copying (no paper feed from bypass). Paper on the bypass table is extremely curled. Check if the forwarding pulley, upper or lower paper feed pulleys of the bypass are deformed. Broken feed switch actuator.
Check visually and replace the feed switch if its actuator is broken. With 5 V DC present at CN13-2 on the engine PCB, check if CN13-1 on the engine PCB remains low when the feed switch is turned on and off. If it does, replace the feed switch. Check and repair if necessary. Check (see page 3-6-80).
Check if the bypass paper feed clutch malfunctions. Electrical problem with the bypass paper feed clutch.
3-6-18
2AD Problem (5) A paper jam in the paper feed section is indicated during copying (jam in copier vertical paper conveying section). Causes/check procedures Broken feed switch actuator. Corrective measures Check visually and replace the feed switch if its actuator is broken. With 5 V DC present at CN13-2 on the engine PCB, check if CN13-1 on the engine PCB goes low when the feed switch is turned on. If not, replace the feed switch. Check visually and replace paper feed switch 1 if its actuator is broken. With 5 V DC present at CN13-5 on the engine PCB, check if CN13-4 on the engine PCB goes low when paper feed switch 1 is turned on. If not, replace paper feed switch 1. Check visually and replace paper feed switch 2 if its actuator is broken. With 5 V DC present at CN13-8 on the engine PCB, check if CN13-7 on the engine PCB goes low when paper feed switch 2 is turned on. If not, replace paper feed switch 2. Check visually and replace paper feed switch 3 if its actuator is broken. With 5 V DC present at CN1311 on the engine PCB, check if CN13-10 on the engine PCB goes low when paper feed switch 3 is turned on. If not, replace paper feed switch 3. Check visually and remedy if necessary. Repair or replace if necessary.
Check if the feed pulleys and feed rollers 1, 2 and 3 do not contact each other. Check if the feed pulleys and feed rollers 1, 2 and 3 are deformed.
3-6-19
2AD Problem (6) A paper jam in the paper feed section is indicated during copying (jam in converging section). (7) A paper jam in the paper feed section is indicated during copying (multiple sheets in paper feed section). (8) A paper jam in the paper feed section is indicated during copying (multiple sheets in copier vertical conveying section). (9) A paper jam in the paper feed section is indicated during copying (multiple sheets before registration section). Causes/check procedures Broken registration switch actuator. Defective registration switch. Corrective measures Check visually and replace the registration switch if its actuator is broken. With 5 V DC present at CN8-B1 on the engine PCB, check if CN8-B2 on the engine PCB goes low when the registration switch is turned on. If not, replace the registration switch. Repair or replace if necessary.
Check if the feed pulleys and feed rollers 1, 2 and 3 are deformed. Check if the feed pulleys and feed rollers 1, 2 and 3 do not contact each other. Check if the feed guides are deformed. Check if the feed guides are deformed.
Check visually and remedy if necessary. Check visually and remedy if necessary. Check visually and remedy if necessary.
Check if the upper, middle and lower feed guide plates are deformed.
3-6-20
2AD Problem (10) A paper jam in the paper conveying section is indicated during copying (jam in registration/ transfer section). (11) A paper jam in the fixing section is indicated during copying (jam in fixing section). Causes/check procedures Check if the registration clutch malfunctions. Electrical problem with the registration clutch. Check if the upper and lower registration rollers contact each other. Check if the upper and lower feed rollers contact each other. Check if the registration clutch malfunctions. Electrical problem with the registration clutch. Check if the upper and lower registration rollers contact each other. Check if the upper and lower feed rollers contact each other. Check if the fixing unit front guide is deformed. Check if the press roller is extremely dirty or deformed. Check if the heat roller separation claws are dirty or deformed. Check if the heat roller and its separation claws contact each other. (12) A paper jam in the eject section is indicated during copying (jam in eject section). Check if the eject roller and eject pulley contact each other. Corrective measures Check visually and remedy if necessary. Check (see page 3-6-80). Check visually and remedy if necessary. Check visually and remedy if necessary. Check and remedy if necessary. Check (see page 3-6-80). Check visually and remedy if necessary. Check visually and remedy if necessary. Repair or replace if necessary. Clean or replace if necessary. Clean or replace if necessary.
3-6-21
2AD Problem (13) A paper jam in the eject section is indicated during copying (jam in switchback eject section). Causes/check procedures Broken switchback eject switch actuator. Defective switchback eject switch. Corrective measures Check visually and replace the switchback eject switch if its actuator is broken. With 5 V DC present at CN3-A2 on the engine PCB, check if CN3-A1 on the engine PCB remains low when the switchback eject switch is turned on and off. If it does, replace the switchback eject switch. Check visually and replace any deformed rollers. Check visually and remedy if necessary.
Check if the left or right switchback feed roller is deformed. Check if the right middle or left switchback eject guide is deformed.
3-6-22
2AD SRDF Problem (1) An original jams when the main switch is turned on. Causes/check procedures A piece of paper torn from an original is caught around the original feed switch. Defective original feed switch. Corrective measures Remove any found.
With 5 V DC present at CN6-B4 on the DF driver PCB, check if CN6-B5 on the DF driver PCB remains low when the original feed switch is turned on and off. If it does, replace the original feed switch. Remove any found.
A piece of paper torn from an original is caught around the original switchback switch. Defective original switchback switch.
With 5 V DC present at CN6-A6 on the DF driver PCB, check if CN6-A5 on the DF driver PCB remains low when the original switchback switch is turned on and off. If it does, replace the original switchback switch. Remove any found.
A piece of paper torn from an original is caught around the DF timing switch. Defective DF timing switch.
With 5 V DC present at CN6-A15 on the DF driver PCB, check if CN6-A14 on the DF driver PCB remains low when the DF timing switch is turned on and off. If it does, replace the DF timing switch. With 5 V DC present at CN6-B4 on the DF driver PCB, check if CN6-B5 on the DF driver PCB remains low when the original feed switch is turned on and off. If it does, replace the original feed switch. Check and remedy.
Check if the original feed motor or the original conveying motor malfunction.
3-6-23
2AD Problem (3) An original jams in the SRDF during copying (a jam in the original feed/ conveying section). Causes/check procedures Defective DF timing switch. Corrective measures With 5 V DC present at CN6-A15 on the DF driver PCB, check if CN6-A14 on the DF driver PCB remains low when the DF timing switch is turned on and off. If it does, replace the DF timing switch. With 5 V DC present at CN6-B4 on the DF driver PCB, check if CN6-B5 on the DF driver PCB remains low when the original feed switch is turned on and off. If it does, replace the original feed switch. With 5 V DC present at CN6-A6 on the DF driver PCB, check if CN6-A5 on the DF driver PCB remains low when the original switchback switch is turned on and off. If it does, replace the original switchback switch. Check and remedy. Check visually and replace the deformed pulley. Check visually and replace the deformed pulley. Check visually and replace the deformed pulley.
Check if the original feed motor malfunctions. Check if the DF original feed pulley or the DF separation pulley is deformed. Check if the DF registration roller or the DF registration pulley is deformed. Check if the lower original conveying roller or the front scanning pulley is deformed.
3-6-24
2AD Problem (3) An original jams in the SRDF during copying (a jam in the original feed/ conveying section). (4) An original jams in the SRDF during copying (a jam in the original switchback section). Causes/check procedures Check if the original conveying motor malfunctions. Check if the middle original conveying roller and middle original conveying pulley contact each other correctly. Corrective measures Check and remedy. Check and remedy.
With 5 V DC present at CN6-A6 on the DF driver PCB, check if CN6-A5 on the DF driver PCB remains low when the original switchback switch is turned on and off. If it does, replace the original switchback switch. With 5 V DC present at CN6-A15 on the DF driver PCB, check if CN6-A14 on the DF driver PCB remains low when the DF timing switch is turned on and off. If it does, replace the DF timing switch. Check and remedy. Check and remedy. Use only originals conforming to the specifications. Clean with isopropyl alcohol.
Check if the original feed motor malfunctions. Check if the original conveying motor malfunctions. (5) Original jams frequently. An original outside the specifications is used. The DF forwarding pulleys, DF original feed pulley or DF switchback pulley is dirty with paper powder. The DF original feed pulley and the DF separation pulley do not contact correctly.
Remedy.
3-6-25
2AD Feedshift and duplex sections Problem (1) A paper jam in the feedshift section is indicated during copying (jam in feedshift section). Causes/check procedures Broken feedshift switch actuator. Defective feedshift switch. Corrective measures Check visually and replace the feedshift switch if its actuator is broken. With 5 V DC present at CN3-A5 on the engine PCB, check if CN3-A4 on the engine PCB goes low when the feedshift switch is turned on. If not, replace the feedshift switch. Check (see page 3-6-93). Check and remedy. Check and remedy. Check visually and replace the duplex paper conveying switch if its actuator is broken. With 5 V DC present at CN9-6 on the engine PCB, check if CN9-8 on the engine PCB goes low when the duplex paper conveying switch is turned on. If not, replace the duplex paper conveying switch. Check visually and replace the duplex registration switch if its actuator is broken. With 5 V DC present at CN9-5 on the engine PCB, check if CN9-7 on the engine PCB goes low when the duplex registration switch is turned on. If not, replace the duplex registration switch. Check visually and replace the duplex eject switch if its actuator is broken.
Electrical problem with the feedshift solenoid. Deformed lower feedshift guide. Incorrect contact between the feedshift lower roller and pulley. (2) A paper jam in the duplex section is indicated during copying (jam in duplex conveying section). Broken duplex paper conveying switch actuator. Defective duplex paper conveying switch.
3-6-26
2AD Problem (2) A paper jam in the duplex section is indicated during copying (jam in duplex conveying section). Causes/check procedures Defective duplex eject switch. Corrective measures With 5 V DC present at CN9-13 on the engine PCB, check if CN9-11 on the engine PCB goes low when the duplex eject switch is tuned on. If not, replace the duplex eject switch. Check and remedy.
Check if upper and lower duplex registration rollers, duplex paper conveying roller and pulley, and duplex eject roller and pulley contact each other correctly. Check if upper or lower duplex registration roller, duplex paper conveying roller or pulley, or duplex eject roller or pulley are deformed.
(3) A paper jam in the duplex section is indicated during copying (jam in duplex stock section).
Check if the duplex forward solenoid malfunctions. Electrical problem with the duplex forward solenoid. Broken switchback eject switch actuator. Defective switchback eject switch.
Check and remedy. Check (see page 3-6-93). Check visually and replace the switchback eject switch if its actuator is broken. With 5 V DC present at CN3-A2 on the engine PCB, check if CN3-A1 on the engine PCB goes low when the switchback eject switch is turned on. If not, replace the switchback eject switch. Check visually and replace the duplex registration switch if its actuator is broken. With 5 V DC present at CN9-5 on the engine PCB, check if CN9-7 on the engine PCB goes low when the duplex registration switch is turned on. If not, replace the duplex registration switch.
3-6-27
2AD Large paper deck Problem (1) A paper jam in the large paper deck is indicated during copying (paper failing to reach PPS0 in large paper deck horizontal paper path). Causes/check procedures Broken deck paper conveying motor gear. Paper is extremely curled. Defective paper path sensor 1. Corrective measures Check visually and replace the deck paper conveying motor or its gear if necessary. Change the paper. With a 5/0 V DC pulse signal output at CN1-1 on the deck main PCB, check if a 2/0 V DC pulse signal is output at CN4-9 on the deck main PCB when paper path sensor 1 is turned on by holding a sheet of paper level about 10 to 20 mm below the bottom of the paper conveying base. If not, paper path sensor 1 or the interface PCB is defective. Check the interface PCB and, if it is okay, replace paper path sensor 1. Check (see page 3-6-96). Remedy or replace. Check the installation condition. Check for continuity across CN1-9 & CN7-2 and CN1-4 & CN5-6 on the interface PCB. If none, replace the interface PCB. Check if the voltage at CN4-9 on the deck main PCB changes in the pattern 2 V DC/0 V DC (pulse) /0 V DC. If it does, replace the deck main PCB.
Electrical problem with paper feed clutch 1. The paper side guides are deformed. Mechanical problem with paper feed clutch 1. Defective interface PCB.
3-6-28
2AD Problem (2) A paper jam in the large paper deck is indicated during copying (paper failing to reach PPS1 in large paper deck horizontal paper path). Causes/check procedures Broken deck paper conveying motor gear. Paper is extremely curled. Defective paper path sensor 2. Corrective measures Check visually and replace the deck paper conveying motor or its gear if necessary. Change the paper. With a 5/0 V DC pulse signal output at CN1-1 on the deck main PCB, check if a 2/0 V DC pulse signal is output at CN1-6 on the deck main PCB with paper path sensor 2 is turned on by holding a sheet of paper level about 10 to 20 mm below the bottom of the paper conveying base. If not, paper path sensor 2 or the interface PCB is defective. Check the interface PCB and, if it is okay, replace paper path sensor 2. Check (see page 3-6-97). Remedy or replace. Check the installation condition. Check for continuity across CN1-6 & CN5-2 and CN2-6 & CN4-8 on the interface PCB. If none, replace the interface PCB. Check if the voltage at CN1-6 on the deck main PCB changes in the pattern 2 V DC/0 V DC (pulse) /0 V DC. If it does, replace the deck main PCB.
Electrical problem with the paper conveying clutch. The paper side guides are deformed. Mechanical problem with the paper conveying clutch. Defective interface PCB.
3-6-29
2AD Problem (3) A paper jam in the large paper deck is indicated during copying (paper failing to reach PPS2 in large paper deck horizontal paper path). Causes/check procedures Broken deck paper conveying motor gear. Paper is extremely curled. Defective paper path sensor 3. Corrective measures Check visually and replace the deck paper conveying motor or its gear if necessary. Change the paper. With a 5/0 V DC pulse signal output at CN1-1 on the deck main PCB, check if a 2/0 V DC pulse signal is output at CN1-11 on the deck main PCB when paper path sensor 3 is turned on by holding a sheet of paper level about 10 to 20 mm below the bottom of the paper conveying base. If not, paper path sensor 3 or the interface PCB is defective. Check the interface PCB and, if it is okay, replace paper path sensor 3. Check (see page 3-6-96). Check the installation condition. Remedy or replace. Check for continuity across CN1-5 & CN5-4 and CN2-11 & CN4-2 on the interface PCB. If none, replace interface the PCB. Check if the voltages at CN1-11 on the deck main PCB change in the pattern 2 V DC/0 V DC (pulse) /0 V DC. If it does, replace the deck main PCB.
Electrical problem with paper feed clutch 2. Mechanical problem with paper feed clutch 2. The paper side guides are deformed. Defective interface PCB.
3-6-30
2AD
LUG5 1
FUSE3
CN5
LUG4
J1522A C306
L302 J1508
J2013A
C305 C301
J2501A J2502A
FUSE5 1 1 CN6
D301
J2010A J1524A J1502 Q601 R604 R603 J1525A C205 J7500 J2011A
J1022
J2007A Q902 J2008A R210 AB8 AB5 AB7 AB4 AB6 AB3 D105
J1011A
Q304
J1012A
J0529
J7502A Q201 R209 D203 D202 D201 SECONDARY PRIMARY J1519A DH1 Q104 LUG3 FUSE2
J1024 J1526A
C310
J1023
R317
L301
R316
J1010A J1009A C204 L201 C202 C201 TRNS 1 C103 R110 R111 R112 R202 R201
J1021
1
J1515 J1513
J7505
J1008A
C403
R304 J0525
J1016
J1521A
J1007A
J0527 1
D101
D102
C108 J1506 C109 J1505 J7503 C106 R107 D106 R114 R113 C102 1 C103 Q109 J0518
CN12
CN11 FAN
R406 C401R904
Q305
J0526 C502
J0524
R303
J7503 D902
R302 R301
C503
J1520A
J0521
D901
R906 J7504 C901 R905
R311
Q302
ZD901
IC7
J1510
R907
D904
Q502 Q501
L402 J0528
J1015
D302
R401
R903
J1013 J1012
D401 R501
C501
Q305
Q401 J2006A R405 C206 C207 R208 J1011 J0513 R206 FB301
R150 R161 Q113 Q112
IC6
CP501 R123
J0522
R204
R802
J0516
R801 J0517
J1509
R162
PC2 L102
R103 D103 R104
R151
R701
J1010
J0514
J2007 R125
C114
R121
J0506
J1005
R126
C118
PC3 ZD105
R136
Q110 C117 R120
C122
PT2 R153
PT1 R152
R141
J7501
R124
D110 Q111
D111
J1006
C110ZD101
C104 J1005A D113 J1518A J1504 R127 R109 R129 TAB1 TAB2 R3 R2 R1
C115 C116
C121
J1004
IC2
J7501A
Q105 Q106
ZD102
C124R102
R139
R140
J1002
R142
R117
R118 FB5
C113 FB6
R146
J2006
R147 FB4
R149
AB2
FB3 FB2
R148
J3001A RF1
C005
J2002A
D108
D107 Q102
J1002A
TR1
LUG2
J1511A FUSE1 C2
J1513A
J1514A
J1510A
J1515A
J1014A
J2014A C002
J2003A
CN9
J1527A TR3
C125
C3 J1504A J1505A
L001
L2
J1506A J1507A
J1512A C126
N OUT
C128
L103
C5
L IN F001
C127
C1 J1503A
C4 C6
C001
3-6-31
2AD Terminals (CN) TB1 TB2 Voltage 120 V AC 220 - 240 V AC TB3 TB4 120 V AC 220 - 240 V AC 1-1 1-2 1-3 1-4 2-1 2-2 2-3 2-4 2-5 2-6 2-7 4-1 4-2 4-3 4-4 4-5 5-1 5-2 5-3 5-4 5-6 5-7 7-1 7-3 7-4 7-6 7-7 7-8 8-1 1-5 1-5 1-6 1-8 24 V DC 24 V DC 24 V DC 24 V DC Remarks 120 V AC supply, input (120 V specs) 220 - 240 V AC supply, input (220 - 240 V specs) 120 V AC supply, output (120 V specs) 220 - 240 V AC supply, output (220 - 240 V specs) 24 V DC supply for OMPCB, output 24 V DC supply for PRY, output 24 V DC supply for EPCB, output 24 V DC supply for SMPCB, output 5 V DC supply for OMPCB, output 5 V DC supply for MPCB, output 5 V DC supply for printer board*, output 5 V DC supply for MPCB, output 5 V DC supply for MCPCB1, output 5 V DC supply for MCPCB2, output 5 V DC supply for EPCB, output 12 V DC supply for SCPCB, output PSPCB SLEEP SIG signal, input PSPCB zero-cross signal, input H1 on/off, input H2 on/off, input 24 V DC supply for finisher*, output 24 V DC supply for finisher*, output 24 V DC supply for finisher*, output 24 V DC supply for finisher*, output 24 V DC supply for SRDF, output 24 V DC supply for SRDF, output 5 V DC supply for finisher*, output 5 V DC supply for SRDF, output 5 V DC supply for SRDF, output 5 V DC supply for SCPCB, output 5 V DC supply for SCPCB, output 5 V DC supply for SMPCB, output 120 V AC supply for MSW, output (120 V specs) 220 - 240 V AC supply for MSW, output (220 - 240 V specs)
3-4, -5, -6, -7 5 V DC 3-4, -5, -6, -7 5 V DC 3-4, -5, -6, -7 5 V DC 3-4, -5, -6, -7 5 V DC 3-4, -5, -6, -7 5 V DC 3-4, -5, -6, -7 5 V DC 3-4, -5, -6, -7 5 V DC 3-3 3-5 3-5 3-9 3-9 12 V DC 0/5 V DC 0/5 V DC (pulse) 0/5 V DC 0/5 V DC
6-1, -2, -3 24 V DC 6-1, -2, -3 24 V DC 6-1, -2, -3 24 V DC 6-1, -2, -3 24 V DC 6-1, -2, -3 24 V DC 6-1, -2, -3 24 V DC 7-9 7-9 7-9 7-9 7-9 7-9 8-2 5 V DC 5 V DC 5 V DC 5 V DC 5 V DC 5 V DC 120 V AC 220 - 240 V AC
* Optional.
3-6-32
2AD Terminals (CN) 10-1 10-2 9-1 9-1 Voltage 120/0 V AC 220 - 240/0 V AC 120/0 V AC 220 - 240/0 V AC Remarks H1 on/off, output (120 V specs) H1 on/off, output (220 - 240 V specs) H2 on/off, output (120 V specs) H2 on/off, output (220 - 240 V specs)
3-6-33
72 71 8 8 8
+ C1 B12
CN2
B1
B11
D2 C2 +
DT1
11
TR1 TR2
TR3 1 ZD1
CN19
IC8
CN20
5 D3 1 IC12 1 IC13 11
B1
A1
DT4
DT3
F1 + DT5 C3
2 1
IC14
TR8
TR12
CN15
CN14
10
B14
1
B1 A9
TR13
IC15 DT6 C5
+
+
1
1 IC16 C4
1 IC18
1 IC19
1 IC20
1 IC21
16 15
ZD2
ZD3
+
CN6
1 C6
0
1 B1 + A11
G
1 A1 1 B10
CN18
8
CN21 RA6 C7 RA5 RA7 RA8 TR15 CN17 2 CN7 1 15 CN13 1 26 25 CN9 2 1 18 17 CN10 2 1 18 17
DT13
F2
F3
2 1
12
CN16
A14
B1
2 1
CN5
A1
CN4
RA3
B C E
IC11
TR4 TR5
TR7
A11
B1
RA1
DT2
R1 R2
1 IC6
1 IC4
TR6
CN3
A1
1 IC2
1 IC3
A1
D1 A12
3-6-34
2AD
2AD Terminals (CN) 1-1 1-3 1-4 1-5 1-6 1-7 1-8 1-9 1-10 1-11 1-12 1-13 1-14 1-15 1-16 1-17 1-18 1-19 1-20 1-21 1-23 1-24 1-25 1-28 1-29 1-30 1-31 1-32 1-33 1-34 1-35 1-36 1-37 1-38 1-39 1-40 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 0 - 5 V DC 24 V DC 0 - 5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC Voltage 0 - 5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0 - 5 V DC 24/0 V DC 24/0 V DC 24/0 V DC 5 V DC 0 - 5 V DC 0 - 5 V DC 0 - 5 V DC 0 - 5 V DC 0 - 5 V DC Remarks TNS detection voltage, output TLDS toner absent/present detection, output TLS on/off, output SBESW on/off, output ESW on/off, output FSSW on/off, output FTH detection voltage, output SSW2 on/off, output SSW3 on/off, output SSW1 on/off, output 5 V DC control voltage for MSW, input TNS control voltage, input HVTPCB SC control voltage, input HVTPCB TC control voltage, input HVTPCB DB control voltage, input HVTPCB GRID control voltage, input ETTH detection voltage, output EHUMSENS detection voltage, output Control voltage for MPCB, output H ALARM signal, output TC on/off, output MMD* 2 connected/not connected, output Finisher* 1 connected/not connected, output STKSW on/off, output DUPRSW on/off, output DUPESW on/off, output DUPPCSW on/off, output PFM LOCK signal, output RSW on/off, output FSW on/off, output PFSW4 on/off, output PFSW3 on/off, output PFSW2 on/off, output PFSW1 on/off, output HVTPCB MC ALM, output HVTPCB ST ALM, output
1-41 2-B10 0/5 V DC PCM LOCK signal, output *1: Optional. *2: Optional for 120 V specifications only.
3-6-35
2AD Terminals (CN) 1-42 1-43 1-44 1-45 1-46 1-47 1-48 1-49 1-50 1-51 1-52 1-53 1-54 1-55 1-56 1-57 1-58 1-59 1-60 1-61 1-62 1-63 1-64 1-65 1-66 1-67 1-68 1-69 1-70 1-71 1-72 1-73 1-75 1-76 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 Voltage 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 5/0 V DC 5/0 V DC 0/5 V DC 5/0 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 5 V DC 5/0 V DC 0/24 V DC 0/24 V DC 0/5 V DC (pulse) 0/5 V DC 0/5 V DC Remarks DM LOCK signal, output PWSW-L (DIG2) on/off, output (inch specs) PWSW-L (DIG1) on/off, output (inch specs) PWSW-L (DIG0) on/off, output (inch specs) PLSW-L on/off, output PWSW-U (DIG2) on/off, output (inch specs) PWSW-U (DIG1) on/off, output (inch specs) PWSW-U (DIG0) on/off, output (inch specs) PLSW-U on/off, output BYPPWSW (DIG2) on/off, output BYPPWSW (DIG1) on/off, output BYPPWSW (DIG0) on/off, output BYPPLSW on/off, output PSW-L on/off, output PSW-U on/off, output BYPPSW on/off, output LICSW-L on/off, output LICSW-U on/off, output BYPEDSW on/off, output SRHPSW on/off, output Duplex unit installed/not installed, output Key card*2 ENABLE signal, output Key card*2, key counter*1 connected/not connected, output Key card*2 control signal, input Key card*2 control signal, input Key card*2 control signal, input Key card*2 control signal, input Control voltage for MPCB, output Control voltage for MPCB, output IFFM on/off, input CL on/off, input TFM/TRM drive clock pulse, input TFM drive control signal, input TRM drive control signal, input
3-6-36
2AD Terminals (CN) 1-77 1-78 1-79 1-80 1-81 1-82 1-83 1-84 1-85 1-86 1-87 1-88 1-89 1-90 1-91 1-92 1-97 1-101 1-102 1-104 1-105 1-106 1-107 1-108 1-109 1-110 1-111 1-112 1-113 1-114 1-115 1-116 1-117 1-118 1-119 1-120 1-121 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 Voltage 0/24 V DC 0/24 V DC 0/24 V DC 24/0 V DC 0/24 V DC 24/0 V DC 0/24 V DC 0/15 V DC 0/20 V DC 0/20 V DC 0/5 V DC 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC 0/5 V DC 0/24 V DC 0/24 V DC 0/24 V DC 0/24 V DC 0/5 V DC 0/5 V DC 0/5 V DC (pulse) 0/5 V DC 0/5 V DC (pulse) 0/5 V DC 0/24 V DC 0/24 V DC 0/5 V DC 0/5 V DC 0/24 V DC 0/24 V DC 0/5 V DC (pulse) 0/5 V DC (pulse) SCL on/off, input FSSOL latch-on signal, input FSSOL release signal, input PRY on/off, input SSW1 control voltage, input MSW OFF signal, input HVTPCB (SC) on/off, input HVTPCB (TC) on/off, input HVTPCB (DB) on/off, input HVTPCB (MC) on/off, input PFM on/off, input PFM drive clock pulse, input MMD* 2 serial signal, input MMD* 2 serial signal, output Finisher* 1 serial signal, input Finisher* 1 serial signal, output MMD* 2 count on/off, input TC on/off, input Finisher* 1 RESET signal, input FCL3 on/off, input FCL2 on/off, input FCL1 on/off, input FCL5 on/off, input H2 on/off, input H1 on/off, input PCM drive clock pulse, input PCM on/off, input DM drive clock pulse, input DM on/off, input PCFM on/off, input RCL on/off, input CCM forward rotation signal, input CCM reverse rotation signal, input CLM-L on/off, input CLM-U on/off, input SRM coil energization pulse, input (B_) SRM coil energization pulse, input (A_) Remarks
3-6-37
2AD Terminals (CN) 1-122 1-123 1-125 1-126 1-127 1-128 1-130 1-131 1-132 1-133 1-134 1-135 1-136 1-137 1-138 1-139 1-140 2-A1 2-A2 2-A3 2-A4 2-A5 2-A6 2-A7 2-A8 2-A9 2-A10 2-B3 2-B4 2-B9 2-B11 2-B12 3-A1 3-A2 3-A4 3-A5 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-A11 2-A11 2-A11 2-A11 2-A11 2-A11 2-A11 2-A11 2-A11 2-A11 2-B2 2-B2 2-B10 2-B10 2-B10 3-A3 3-A3 3-A6 3-A6 Voltage 0/5 V DC (pulse) 0/5 V DC (pulse) 0/24 V DC 0/24 V DC 0/24 V DC 0/24 V DC 0/24 V DC 0/24 V DC 0/24 V DC 0/24 V DC 0/24 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/24 V DC 24 V DC 0/24 V DC 24 V DC 0/24 V DC 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 5 V DC 0/5 V DC 0/5 V DC 5 V DC 0 - 15 V DC 0 - 5 V DC 24 V DC 0/5 V DC 5 V DC 0/5 V DC 5 V DC Remarks SRM coil energization pulse, input (B) SRM coil energization pulse, input (A) SBFSSOL release signal, input SBFSSOL latch-on signal, input DUPPTSOL on/off, input DUPFWDSOL on/off, input FCL4 on/off, input PFCL-L on/off, input PFCL-U on/off, input BYPSOL on/off, input BYPPFCL on/off, input Key card*2 control signal, input Key card*2 control signal, input Key card*2 control signal, input Key card*2 control signal, input Key card*2, key counter*1 copy count signal, input Key card*2 on/off, output 24 V DC supply for CL, output CL on/off, output 24 V DC supply for IFFM, output IFFM on/off, output TFM drive control signal (), output TFM drive control signal (+), output TRM drive control signal (), output TRM drive control signal (+), output 5 V DC supply for TLS, output TLS on/off, input TLDS toner absent/present, input 5 V DC supply for TLDS, output TNS control voltage, output TNS detection voltage, input 24 V DC supply for TNS, output SBESW on/off, input 5 V DC supply for SBESW, output FSSW on/off, input 5 V DC supply for FSSW, output
3-6-38
2AD Terminals (CN) 3-A7 3-A8 3-A9 3-A10 3-A11 3-B1 3-B2 3-B3 3-B4 3-B5 3-B6 3-B7 3-B8 3-B9 3-B10 4-1 4-2 4-3 4-4 4-5 4-6 4-7 4-8 4-9 4-10 5-A1 5-A3 5-A4 5-A6 5-A7 5-A8 5-A9 5-B1 5-B3 5-B4 5-B5 3-A6 3-A6 3-A6 3-A6 3-A6 3-A6 3-A6 3-A6 3-A6 3-A6 3-A6 3-B11 3-B11 3-B11 3-B11 3-B11 3-B11 3-B11 3-B11 3-B11 3-B11 3-B11 3-B11 3-B11 3-B11 5-A2 5-A2 5-A2 5-A10 5-A10 5-A10 5-A10 5-B2 5-B9 5-B9 5-B9 0 - 5 V DC 5 V DC 0/5 V DC (pulse) 0/5 V DC 0/5 V DC 5 V DC 24 V DC 0/5 V DC 0 - 5 V DC 0/24 V DC Voltage 24 V DC 0/24 V DC 0/24 V DC 0/24 V DC 0/24 V DC 24 V DC 0/5 V DC 24 V DC 0/5 V DC 24 V DC 0/5 V DC 5 V DC 0 - 5 V DC 0/5 V DC 5 V DC 24/0 V DC 0/24 V DC 24/0 V DC 24/0 V DC 24/0 V DC 24/0 V DC 24/0 V DC 24/0 V DC 24 V DC 24/0 V DC Remarks 24 V DC supply for FSSOL, output FSSOL latch-on signal, output FSSOL release signal, output 24 V DC supply for ESCL, output ESCL on/off, output 24 V DC supply for TC, output TC on/off, input 24 V DC supply for CFM1, output CFM1 on/off, output 24 V DC supply for CFM2, output CFM2 on/off, output 5 V DC supply for FTH, output FTH detection voltage, input ESW on/off, input 5 V DC supply for ESW, output SSW1 on/off, input SSW2 on/off SOURCE, output SSW3 on/off, input PRY on/off SOURCE, output 24 V DC supply for MSW, output Control voltage for SSW1, output SSW2 on/off, input SSW3 on/off SOURCE, output PRY on/off, output MSW off signal, output ETTH detection voltage, input EHUMSENS detection voltage, input 5 V DC supply for HUMPCB, output PCM drive clock pulse, output PCM LOCK signal, output PCM on/off, input 5 V DC control voltage for PCM, output 24 V DC supply for PCM, output 24 V DC supply for HVTPCB, output HVTPCB ST ALM, input HVTPCB SC control voltage, output HVTPCB (SC) on/off, output
3-6-39
2AD Terminals (CN) 5-B6 5-B7 5-B8 5-B10 5-B11 5-B12 5-B13 6-1 6-3 6-5 6-7 6-8 7-1 8-A2 8-A3 8-A4 8-A5 8-A8 8-A10 8-B1 8-B2 8-B4 8-B5 8-B6 8-B7 8-B8 8-B9 8-B10 8-B11 9-1 9-5 9-6 9-7 9-8 9-11 9-12 9-13 * Optional. 5-B9 5-B9 5-B9 5-B9 5-B9 5-B9 5-B9 6-2, -6 6-4 6-2, -6 6-4 6-4 7-2 8-B3 8-B3 8-B3 8-B3 8-A7 8-A9 8-B3 8-B3 8-B3 8-B3 8-B3 8-B3 8-B3 8-B3 8-B3 8-B3 9-2 9-3 9-4 9-3 9-4 9-9 9-10 9-9 Voltage 0 - 5 V DC 0/15 V DC 0 - 5 V DC 0/20 V DC 0/5 V DC 0 - 5 V DC 0/20 V DC 24 V DC 5 V DC 24 V DC 0/5 V DC 0/5 V DC 24 V DC 24 V DC 0/24 V DC 24 V DC 0/24 V DC 0/5 V DC 0/5 V DC 5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 24 V DC 0/24 V DC 24 V DC 0/24 V DC 24 V DC 0/24 V DC 0/5 V DC 5 V DC 5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 5/0 V DC 5 V DC Remarks HVTPCB TC control voltage, output HVTPCB (TC) on/off, output HVTPCB DB control voltage, output HVTPCB (DB) on/off, output HVTPCB MC ALM, input HVTPCB GRID control voltage, output HVTPCB (MC) on/off, output 24 V DC supply for EPCB, input 5 V DC supply for EPCB, input 24 V DC supply for PRY, output H1 on/off, output H2 on/off, output 24 V DC supply for LSU, output 24 V DC supply for CLM-U, output CLM-U on/off, output 24 V DC supply for CLM-L, output CLM-L on/off, output PLSW-U on/off, input PLSW-L on/off, input 5 V DC supply for RSW, output RSW on/off, input CCM forward rotation signal, output CCM reverse rotation signal, output 24 V DC supply for PCFM, output PCFM on/off, output 24 V DC supply for FCL4, output FCL4 on/off, output 24 V DC supply for RCL, output RCL on/off, output Finisher* connected/not connected, input 5 V DC supply for DUPRSW, output 5 V DC supply for DUPPCSW, output DUPRSW on/off, input DUPPCSW on/off, input DUPESW on/off, input SRHPSW on/off, input 5 V DC supply for DUPESW, output
3-6-40
2AD Terminals (CN) 9-14 9-15 9-16 9-19 9-20 9-21 9-23 9-24 9-25 10-1 10-2 10-3 10-4 10-5, -6 10-7 10-8 10-9 10-10 10-12 10-13 10-14 11-1 11-2 11-3 11-4 11-8, -9 12-A1 12-A2 12-A3 12-A4 12-A7 12-A8 12-A9 12-A10 12-B2 12-B3 12-B4 9-10 9-17 9-17 9-22 9-22 9-22 9-26 9-26 9-26 12-B6 12-B6 12-B6 12-B6 12-B7 12-B7 12-B7 12-B7 12-B7 12-B7 12-B7 12-B7 11-5 11-5 11-5 11-5 11-6, -7 12-B7 12-B7 12-B7 12-B7 12-B7 12-B7 12-B7 12-B7 12-B6 12-B6 12-B6 Voltage 5 V DC 5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 24 V DC 24 V DC 0/24 V DC 24 V DC 0/24 V DC 0/24 V DC 24 V DC 0/24 V DC 0/5 V DC (pulse) 0/5 V DC 0/5 V DC 5 V DC 24 V DC 24 V DC 0/24 V DC 24 V DC 0/24 V DC 24 V DC 0/24 V DC 24 V DC 0/24 V DC 0/5 V DC (pulse) 0/5 V DC 0/5 V DC Remarks 5 V DC supply for SRHPSW, output 5 V DC supply for STKSW, output STKSW on/off, input PWSW-U (DIG0) on/off, input (inch specs) PWSW-U (DIG1) on/off, input (inch specs) PWSW-U (DIG2) on/off, input (inch specs) PWSW-L (DIG0) on/off, input (inch specs) PWSW-L (DIG1) on/off, input (inch specs) PWSW-L (DIG2) on/off, input (inch specs) SRM coil energization pulse, output (B_) SRM coil energization pulse, output (A_) SRM coil energization pulse, output (B) SRM coil energization pulse, output (A) 24 V DC supply for SRM, output 24 V DC supply for DUPFWDSOL, output DUPFWDSOL on/off, output 24 V DC supply for SBFSSOL, output SBFSSOL latch-on signal, output SBFSSOL release signal, output 24 V DC supply for DUPPTSOL, output DUPPTSOL on/off, output PFM drive clock pulse, output PFM LOCK signal, input PFM on/off, output 5 V DC supply for PFM, output 24 V DC supply for PFM, output 24 V DC supply for FCL5, output FCL5 on/off, output 24 V DC supply for FCL1, output FCL1 on/off, output 24 V DC supply for FCL2, output FCL2 on/off, output 24 V DC supply for FCL3, output FCL3 on/off, output DM drive clock pulse, output DM LOCK signal, input DM on/off, output
3-6-41
2AD Terminals (CN) 12-B5 13-1 13-2 13-4 13-5 13-7 13-8 13-10 13-11 13-13 13-14 14-A2 14-A4 14-A5 14-A6 14-A7 14-A8 14-B2 14-B3 14-B4 14-B5 14-B8 14-B9 15-1 15-2 15-3 15-4 15-7 15-8 15-9 15-10 15-13 15-14 15-15 15-16 16-1 12-B6 13-3 13-3 13-6 13-6 13-9 13-9 13-12 13-12 13-15 13-15 14-A3 14-A3 14-A9 14-A9 14-A9 14-A9 14-B1 14-B1 14-B1 14-B6 14-B7 14-B7 15-5 15-6 15-5 15-6 15-11 15-12 15-11 15-12 15-12 15-12 15-12 15-12 16-6 Voltage 5 V DC 0/5 V DC 5 V DC 0/5 V DC 5 V DC 0/5 V DC 5 V DC 0/5 V DC 5 V DC 0/5 V DC 5 V DC 5 V DC 0/5 V DC 24 V DC 24 V DC 0/24 V DC 0/24 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 5 V DC 5 V DC 5 V DC 5/0 V DC 5/0 V DC 5 V DC 5 V DC 0/5 V DC 0/5 V DC 0/24 V DC 0/24 V DC 24 V DC 24 V DC 24 V DC Remarks 5 V DC supply for DM, output 24 V DC supply for DM, output FSW on/off, input 5 V DC supply for FSW, output PFSW1 on/off, input 5 V DC supply for PFSW1, output PFSW2 on/off, input 5 V DC supply for PFSW2, output PFSW3 on/off, input 5 V DC supply for PFSW3, output PFSW4 on/off, input 5 V DC supply for PFSW4, output 5 V DC supply for BYPPSW, output BYPPSW on/off, input 24 V DC supply for BYPPFCL, output 24 V DC supply for BYPSOL, output BYPPFCL on/off, output BYPSOL on/off, output BYPPWSW (DIG2) on/off, input BYPPWSW (DIG1) on/off, input BYPPWSW (DIG0) on/off, input BYPEDSW on/off, input BYPPLSW on/off, input 5 V DC supply for BYPPLSW, output 5 V DC supply for LICSW-U, output 5 V DC supply for LICSW-L, output LICSW-U on/off, input LICSW-L on/off, input 5 V DC supply for PSW-U, output 5 V DC supply for PSW-L, output PSW-U on/off, input PSW-L on/off, input PFCL-U on/off, output PFCL-L on/off, output 24 V DC supply for PFCL-U, output 24 V DC supply for PFCL-L, output 24 V DC supply for MMD*, output
3-6-42
2AD Terminals (CN) 16-2 16-5 16-8 16-10 16-12 17-2 17-4 17-6 17-7 17-17 19-A1 19-A2 19-A3 19-A4 19-A5 19-A6 19-A7 19-A8 19-A9 19-A10 19-B1 19-B2 19-B3 19-B4 19-B5 19-B6 19-B7 19-B8 19-B10 16-7 16-6 16-7 16-9 16-11 17-1 17-5 17-5 17-3 17-18 19-B9 19-B9 19-B9 19-B9 19-B9 19-B9 19-B9 19-B9 19-B9 19-B9 19-B9 19-B9 19-B9 19-B9 19-B9 19-B9 19-B9 19-B9 19-B10 Voltage 0/5 V DC (pulse) 24 V DC 0/5 V DC 0/5 V DC (pulse) 0/5 V DC (pulse) 5 V DC 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC 24 V DC 5 V DC 5 V DC 5 V DC 5 V DC 5 V DC 5 V DC 5 V DC 5 V DC 0/5 V DC 24 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC Remarks MMD* count on/off, output 24 V DC supply for MMD*, output MMD* connected/not connected, input Serial signal MMD*, output MMD* serial signal, input 5 V DC supply for large paper deck, output Large paper deck serial signal, input Large paper deck serial signal, output Large paper deck PFSW4 on/off, output 24 V DC supply for large paper deck, output 5 V DC control voltage for key card*, output 5 V DC control voltage for key card*, output 5 V DC control voltage for key card*, output 5 V DC control voltage for key card*, output 5 V DC control voltage for key card*, output 5 V DC control voltage for key card*, output 5 V DC control voltage for key card*, output 5 V DC control voltage for key card*, output Key card* ENABLE signal, input 24 V DC supply for key card*, output Key card* control signal, output Key card* control signal, output Key card* control signal, output Key card* control signal, output Key card* control signal, output Key card* control signal, output Key card* control signal, output Key card* control signal, output Key card* on/off, output
3-6-43
2AD Terminals (CN) 20-1 20-2 20-3 21-2 21-4 21-5 21-6 20-4 20-4 20-4 21-1 21-3 21-1 21-1 Voltage 24 V DC 0/5 V DC 0/5 V DC 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC 0/5 V DC Remarks 24 V DC supply for key card*2, output Key card*2, key counter*1 copy count signal, output Key card*2, key counter*1 connected/not connected, input Finisher*1 serial signal, output Finisher*1 serial signal, input Finisher*1 RESET signal, output Finisher*1 connected/not connected, input
3-6-44
1 CN8
5 1
13 1
11
CN6
69
IC5 5
IC6
8 1 15 15 IC16 1
RA1
IC12 IC17
1 IC13
RA2
80 81
IC21 51
1 IC14 RA10 1 4
CN5
1 IC9 1
1 IC8
IC18
1 IC20
CN1
11
11
1 IC25
1 IC26
1 IC27
11 64
13 25 26
8 65 64 49 1 IC34 48 1 IC38
1 IC35
1 IC36
1 IC37
RA19
RA20
RA21
TR6 TR5
C4
11 17 16 33 32 51 1 IC48 1 IC44 +
9 1 IC45 1 IC46
72
1 4
71
IC47
1 IC49
1 IC50
1 IC51
1 IC52
IC33 1 B1 A1
1 IC54
1 IC55
B1 A1
CN3
B16 A16
2 16 17
CN4
1 IC30 41 40
11
11
15 14 30 29
1 2
33 34
3-6-45
10 9 80 65 64 24 41 25 40
2AD
2AD Terminals (CN) 1-1 1-3 1-4 1-5 1-6 1-7 1-8 1-9 1-10 1-11 1-12 1-13 1-14 1-15 1-16 1-17 1-18 1-19 1-20 1-21 1-23 1-24 1-25 1-28 1-29 1-30 1-31 1-32 1-33 1-34 1-35 1-36 1-37 1-38 1-39 1-40 1-41 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-B10 0 - 5 V DC 24 V DC 0 - 5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC Voltage 0 - 5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0 - 5 V DC 24/0 V DC 24/0 V DC 24/0 V DC 5 V DC 0 - 5 V DC 0 - 5 V DC 0 - 5 V DC 0 - 5 V DC 0 - 5 V DC Remarks TNS detection voltage, input TLDS toner absent/present, input TLS on/off, input SBESW on/off, input ESW on/off, input FSSW on/off, input FTH detection voltage, input SSW2 on/off, input SSW3 on/off, input SSW1 on/off, input 5 V DC control voltage for MSW, output TNS control voltage, output HVTPCB SC control voltage, output HVTPCB TC control voltage, output HVTPCB DB control voltage, output HVTPCB GRID control voltage, output ETTH detection voltage, input EHUMSENS detection voltage, input Control voltage for MPCB, input H ALARM control voltage, input TC on/off, input MMD*2 connected/not connected, input Finisher*1 connected/not connected, input STKSW on/off, input DUPRSW on/off, input DUPESW on/off, input DUPPCSW on/off, input PFM LOCK signal, input RSW on/off, input FSW on/off, input PFSW4 on/off, input PFSW3 on/off, input PFSW2 on/off, input PFSW1 on/off, input HVTPCB MC ALM, input HVTPCB ST ALM, input PCM LOCK signal, input
3-6-46
2AD Terminals (CN) 1-42 1-43 1-44 1-45 1-46 1-47 1-48 1-49 1-50 1-51 1-52 1-53 1-54 1-55 1-56 1-57 1-58 1-59 1-60 1-61 1-62 1-63 1-64 1-65 1-66 1-67 1-68 1-69 1-70 1-71 1-72 1-73 1-75 1-76 1-77 1-78 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 2-B10 Voltage 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 5/0 V DC 5/0 V DC 0/5 V DC 5/0 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 5 V DC 5/0 V DC 0/24 V DC 0/24 V DC 0/5 V DC (pulse) 0/5 V DC 0/5 V DC 0/24 V DC 0/24 V DC Remarks DM LOCK signal, input PWSW-L (DIG2) on/off, input (inch specs) PWSW-L (DIG1) on/off, input (inch specs) PWSW-L (DIG0) on/off, input (inch specs) PLSW-L on/off, input PWSW-U (DIG2) on/off, input (inch specs) PWSW-U (DIG1) on/off, input (inch specs) PWSW-U (DIG0) on/off, input (inch specs) PLSW-U on/off, input BYPPWSW (DIG2) on/off, input BYPPWSW (DIG1) on/off, input BYPPWSW (DIG0) on/off, input BYPPLSW on/off, input PSW-L on/off, input PSW-U on/off, input BYPPSW on/off, input LICSW-L on/off, input LICSW-U on/off, input BYPEDSW on/off, input SRHPSW on/off, input Duplex unit installed/not installed, input Key card* 2 ENABLE signal, input Key card* 2, key counter*1 connected/not connected, input Key card* 2 control signal, output Key card* 2 control signal, output Key card* 2 control signal, output Key card* 2 control signal, output Control voltage for MPCB, input Control voltage for MPCB, input IFFM on/off, output CL on/off, output TFM/TRM drive clock pulse, output TFM drive control signal, output TRM drive control signal, output SCL on/off, output FSSOL latch-on signal, output
1-79 2-B10 0/24 V DC FSSOL release signal, output *1: Optional. *2: Optional for 120 V specifications only.
3-6-47
2AD Terminals (CN) 1-80 1-81 1-82 1-83 1-84 1-85 1-86 1-87 1-88 1-89 1-90 1-91 1-92 1-97 1-101 1-102 1-104 1-105 1-106 1-107 1-108 1-109 1-110 1-111 1-112 1-113 1-114 1-115 1-116 1-117 1-118 1-119 1-120 1-121 1-122 1-123 1-125 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 Voltage 24/0 V DC 0/24 V DC 24/0 V DC 0/24 V DC 0/15 V DC 0/20 V DC 0/20 V DC 0/5 V DC 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC 0/5 V DC 0/24 V DC 0/24 V DC 0/24 V DC 0/24 V DC 0/5 V DC 0/5 V DC 0/5 V DC (pulse) 0/5 V DC 0/5 V DC (pulse) 0/5 V DC 0/24 V DC 0/24 V DC 0/5 V DC 0/5 V DC 0/24 V DC 0/24 V DC 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/24 V DC Remarks PRY on/off, output SSW1 control voltage, output MSW OFF signal, output HVTPCB (SC) on/off, output HVTPCB (TC) on/off, output HVTPCB (DB) on/off, output HVTPCB (MC) on/off, output PFM on/off, output PFM drive clock pulse, output MMD*2 serial signal, output MMD*2 serial signal, input Finisher*1 serial signal, output Finisher*1 serial signal, input MMD*2 count on/off, output TC on/off, output Finisher*1 RESET signal, output FCL3 on/off, output FCL2 on/off, output FCL1 on/off, output FCL5 on/off, output H2 on/off, output H1 on/off, output PCM drive clock pulse, output PCM on/off, output DM drive clock pulse, output DM on/off, output PCFM on/off, output RCL on/off, output CCM forward rotation signal, output CCM reverse rotation signal, output CLM-L on/off, output CLM-U on/off, output SRM coil energization pulse, output (B_) SRM coil energization pulse, output (A_) SRM coil energization pulse, output (B) SRM coil energization pulse, output (A) SBFSSOL release signal, output
3-6-48
2AD Terminals (CN) 1-126 1-127 1-128 1-130 1-131 1-132 1-133 1-134 1-135 1-136 1-137 1-138 1-139 1-140 2-A1 2-A2 2-A3 2-A5 2-A6 2-A7 2-A8 2-A9 2-A10 2-A11 2-A12 2-A14 2-A16 2-B1 2-B2 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A4 2-A13 2-A13 2-A15 2-B6 2-B6 Voltage 0/24 V DC 0/24 V DC 0/24 V DC 0/24 V DC 0/24 V DC 0/24 V DC 0/24 V DC 0/24 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/24 V DC 0/5 V DC 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC Remarks SBFSSOL latch-on signal, output DUPPTSOL on/off, output DUPFWDSOL on/off, output FCL4 on/off, output PFCL-L on/off, output PFCL-U on/off, output BYPSOL on/off, output BYPPFCL on/off, output Key card* 2 control signal, output Key card* 2 control signal, output Key card* 2 control signal, output Key card* 2 control signal, output Key card* 2, key counter*1 copy count signal, output Key card* 2 on/off, input MCPCB1 image control signal MCPSEL, output MCPCB1 serial communication signal, output MCPCB1 communication control signal MCP1 ACK, input MCPCB1 serial communication signal, input MCPCB1 control signal ENGACK MCP1, output MCPCB1 communication control signal R RDY MCP1, input MCPCB1 communication control signal W RDY MCP1, input MCPCB1 control signal PVSYNC, output MCPCB1 image control signal PHSYNC, output MCPCB1 image control clock pulse, input MCPCB1 control signal MCP MREW, input MCPCB1 control signal MCP IDA, input MCPCB1 control signal MCP IDB, input MCPCB1 control signal SEMCP MCP1, input MCPCB1 RESET signal, output
3-6-49
2AD Terminals (CN) 2-B3 2-B4 2-B5 2-B8 2-B9 2-B10 2-B11 2-B12 2-B13 2-B14 2-B15 3-A1 3-A2 3-A3 3-A5 3-A6 3-A7 3-A8 3-A9 3-A10 3-A11 3-A12 3-A14 3-A16 2-B6 2-B6 2-B6 2-B7 2-B7 2-B7 2-B7 2-B7 2-B7 2-B7 2-B7 3-A4 3-A4 3-A4 3-A4 3-A4 3-A4 3-A4 3-A4 3-A4 3-A4 3-A13 3-A13 3-A15 Voltage 0/5 V DC 0/5 V DC (pulse) 0/5 V DC 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC 0/5 V DC 0/5 V DC Remarks MCPCB1 image control signal WCK, output MCPCB1 control signal OVSYNC, output MCPCB1 image control signal MRE, output MCPCB1 image control signal DATA0, output MCPCB1 image control signal DATA1, output MCPCB1 image control signal DATA2, output MCPCB1 image control signal DATA3, output MCPCB1 image control signal DATA4, output MCPCB1 image control signal DATA5, output MCPCB1 image control signal DATA6, output MCPCB1 image control signal DATA7, output MCPCB2 image control signal MCPSEL, output MCPCB2 serial communication signal, output MCPCB2 communication control signal MCP2 ACK, input MCPCB2 serial communication signal, input MCPCB2 control signal ENGACK MCP2, output MCPCB2 communication control signal R RDY MCP2, input MCPCB2 communication control signal W RDY MCP2, input MCPCB2 control signal PVSYNC, output MCPCB2 image control signal PHSYNC, output MCPCB2 image control clock pulse, input MCPCB2 control signal MCP MREW, input MCPCB2 control signal MCP IDA, input MCPCB2 control signal MCP IDB, input
3-6-50
2AD Terminals (CN) 3-B1 3-B2 3-B3 3-B4 3-B5 3-B8 3-B9 3-B10 3-B11 3-B12 3-B13 3-B14 3-B15 4-2 4-3 4-5 4-6 4-8 4-9 4-10 4-11 4-12 4-14 4-16 4-18 4-20 4-22 4-23 4-24 4-25 * Optional. 3-B6 3-B6 3-B6 3-B6 3-B6 3-B7 3-B7 3-B7 3-B7 3-B7 3-B7 3-B7 3-B7 4-1 4-1 4-4 4-4 4-7 4-7 4-7 4-7 4-7 4-13 4-17 4-17 4-19 4-21 4-21 4-21 4-26 Voltage 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC (pulse) 0/5 V DC 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/3.3 V DC (pulse) 0/5 V DC 0/5 V DC (pulse) 0/3.3 V DC 0/3.3 V DC 0/3.3 V DC 0/5 V DC 0/3.3 V DC 0/5 V DC 0/5 V DC 0/3.3 V DC (pulse) 0/3.3 V DC (pulse) 0/3.3 V DC 0/3.3 V DC (pulse) 0/3.3 V DC (pulse) 0/3.3 V DC (pulse) 0/3.3 V DC (pulse) Remarks MCPCB2 control signal SEMCP MCP2, input MCPCB2 RESET signal, output MCPCB2 image control signal WCK, output MCPCB2 control signal OVSYNC, output MCPCB2 image control signal MRE, output MCPCB2 image control signal DATA0, output MCPCB2 image control signal DATA1, output MCPCB2 image control signal DATA2, output MCPCB2 image control signal DATA3, output MCPCB2 image control signal DATA4, output MCPCB2 image control signal DATA5, output MCPCB2 image control signal DATA6, output MCPCB2 image control signal DATA7, output Printer board* serial signal, input Printer board* ENGACK PRT signal, output Printer board* serial signal, output Printer board* PRT ACK signal, input Printer board* PRINT signal, input Printer board* SETPRT signal, input Printer board* MRDY signal, output Printer board* P1 signal, input Printer board* P2 signal, output Printer board* PRTRST signal, output Printer board* clock pulse, input Printer board* POVSYNC signal, input Printer board* PMRE signal, input Printer board* PID0 signal, input Printer board* PID1 signal, input Printer board* PID2 signal, input Printer board* PID3 signal, input
3-6-51
2AD Terminals (CN) 4-27 4-28 4-29 4-30 5-1 5-2 5-3 5-4 5-5 5-6 5-7 5-8 5-9 5-10 5-11 5-12 5-13 5-15 5-16 5-17 5-18 5-19 5-20 5-21 5-22 5-23 5-24 5-25 5-26 5-27 5-28 5-29 5-31 5-32 5-33 4-26 4-26 4-26 4-26 5-14 5-14 5-14 5-14 5-14 5-14 5-14 5-14 5-14 5-14 5-14 5-14 5-14 5-14 5-14 5-14 5-14 5-14 5-14 5-14 5-14 5-14 5-14 5-30 5-30 5-30 5-30 5-30 5-30 5-30 5-34 Voltage 0/3.3 V DC (pulse) 0/3.3 V DC (pulse) 0/3.3 V DC (pulse) 0/3.3 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC 0/5 V DC (pulse) 0/5 V DC 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC 0/5 V DC (pulse) 0/5 V DC 0/5 V DC (pulse) 0/5 V DC 0/5 V DC (pulse) 0/5 V DC 0/5 V DC (pulse) 0/5 V DC 0/5 V DC (pulse) 0/5 V DC 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC Remarks Printer board* PID4 signal, input Printer board* PID5 signal, input Printer board* PID6 signal, input Printer board* PID7 signal, input SCPCB image control signal SID0 +, input SCPCB SOVSYNC + signal, input SCPCB image control signal SID0 , input SCPCB SOVSYNC signal, input SCPCB image control signal SID1 +, input SCPCB SMRE + signal, input SCPCB image control signal SID1 , input SCPCB SMRE signal, input SCPCB image control signal SID2 +, input SCPCB clock pulse +, input SCPCB image control signal SID2 , input SCPCB clock pulse , input SCPCB image control signal SID3 +, input SCPCB image control signal SID3 , input SCPCB SCN HEADER signal, input SCPCB image control signal SID4 +, input SCPCB SCN ACK signal, input SCPCB image control signal SID4 , input SCPCB SC TIM signal, input SCPCB image control signal SID5 +, input SCPCB ENG HEADER SCN signal, output SCPCB image control signal SID5 , input SCPCB ENGAKU SCN signal, output SCPCB image control signal SID6 +, input SCPCB SCAN START signal, output SCPCB image control signal SID6 , input SCPCB serial communication signal, input SCPCB image control signal SID7 +, input SCPCB image control signal SID7 , input SCPCB serial communication signal, output SCPCB RESET SCN signal, output
* Optional.
3-6-52
2AD Terminals (CN) 6-2 6-3 6-5 6-6 6-7 6-8 6-9 7-2 7-3 7-4 7-5 7-7 7-9 7-11 7-13 8-2 8-3 8-5 9-1 9-3 9-4 10-1 10-2 10-4 10-5 6-1 6-4 6-4 6-4 6-4 6-10 6-10 7-1 7-1 7-1 7-1 7-6 7-8 7-10 7-12 8-1 8-1 8-4 9-2 9-2 9-2 10-3 10-3 10-3 10-3 Voltage 0/5 V DC (pulse) 0/5 V DC 0/5 V DC (pulse) 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 5 V DC 0/5 V DC 0/5 V DC 5 V DC 0/5 V DC (pulse) 0/5 V DC 0/5 V DC 5 V DC 0/5 V DC 5 V DC 0/5 V DC (pulse) Remarks OMPCB serial communication signal, output OMPCB MMI ACK signal, input OMPCB serial communication signal, input OMPCB ENGACK MMI signal, output OMPCB MMI ERROR signal, input OMPCB ENG ERROR MMI signal, output OMPCB RESET MMI signal, output LSU VD2 signal, output LSU VD2 + signal, output LSU VD1 signal, output LSU VD1 + signal, output LSU ENABLE signal, output LSU ADJUST2 signal, output LSU ADJUST1 signal, output 24 V DC supply for LSU, output LSU BD signal, input LSU BD + signal, input 24 V DC supply for LSU, output LSU clock pulse, output LSU START signal, output LSU READY signal, output 5 V DC supply for MPCB, input PSPCB SLEEP SIG, output 5 V DC supply for MPCB, input Zero-cross signal, output
3-6-53
CE1 CN1 A1 B1 GND RA1 RA2 RA3 RA4 RA5 RA6 U10 CT3 A16 B16 + CE2 CT2 0 + 1 5 91 RA8 RA7 1 U6 4 U5 15 1 TP1 U2 G TP3 1 TP4 1 U4 TP2 U3 + CT1 + +
2 CN2 1 U1 1
L2
L1
GND
U7 RA13 RA14 RA15 RA16 1 U14 1 U13 22 RA39 RA40 1 U18 22 RA108 GND
U8
U9
CE4 1 U20
RA66 RA68
RA61 RA62
RA65
RA76 RA77 RA78 RA79 RA72 RA73 RA74 RA75 U25 + CE5
RA69 RA67 RA63 RA64 RA70 RA71 RA80 RA81 RA82 RA83 RA84 RA85 U21 U22 U23 U24
CE6
RA90 RA91
RA92 RA93
RA94
CE8
RA95
RA96 RA97 71 72
CN4
1 2
CN5
1 2 RA98 RA99 RA104 RA105 RA100 RA101 + + L5 CE9 CE11 GND RA102 RA103 +
RA109 RA111
3-6-54
304
229
228
U16
76
153
77
152
144
144
108 109
109
108
U26
37 36
37 36
73
73
72
72
1 11 F1 RA38 1 U19 22 L3 22
CE3
1 11 RA12 RA20 RA21 RA25 RA36 RA48 RA57 RA60 RA28 RA30 RA33 RA42 RA44 RA51 RA55 F2 L4 X4 F3
8 1 U11 TP5
X2 RA19 1 11
X1 RA17 TP7 TP8 TP9 RA23 RA29 RA32 TP10 RA46 TP11 RA52 RA56 RA86 RA87 11 RA89 RA88 RA47 RA50 RA54 RA35 RA43 144 RA58 109 RA24 RA59 1 1
108
15 RA22 11
21
2AD Terminals (CN) 1-A1 1-A2 1-A3 1-A5 1-A6 1-A7 1-A8 1-A9 1-A10 1-A11 1-A12 1-A14 1-A16 1-B1 1-B2 1-B3 1-B4 1-B5 1-B8 1-B9 1-B10 1-B11 1-B12 1-A4 1-A4 1-A4 1-A4 1-A4 1-A4 1-A4 1-A4 1-A4 1-A4 1-A13 1-A13 1-A15 1-B6 1-B6 1-B6 1-B6 1-B6 1-B7 1-B7 1-B7 1-B7 1-B7 Voltage 0/5 V DC 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC (pulse) 0/5 V DC 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) Remarks MCPCB1, 2 image control signal MCPSEL, input MCPCB1, 2 serial communication signal, input MCPCB1, 2 communication control signal MCP1 ACK, output MCPCB1, 2 serial communication signal, output MCPCB1, 2 control signal ENGACK MCP1, input MCPCB1, 2 communication control signal R RDY MCP1, output MCPCB1, 2 communication control signal W RDY MCP1, output MCPCB1, 2 control signal PVSYNC, input MCPCB1, 2 image control signal PHSYNC, input MCPCB1, 2 image control clock pulse, output MCPCB1, 2 control signal MCP MREW, output MCPCB1, 2 control signal MCP IDA, output MCPCB1, 2 control signal MCP IDB, output MCPCB1, 2 control signal SEMCP MCP1, output MCPCB1, 2 RESET signal, input MCPCB1, 2 image control signal WCK, input MCPCB1, 2 control signal OVSYNC, input MCPCB1, 2 image control signal MRE, input MCPCB1, 2 image control signal DATA0, input MCPCB1, 2 image control signal DATA1, input MCPCB1, 2 image control signal DATA2, input MCPCB1, 2 image control signal DATA3, input MCPCB1, 2 image control signal DATA4, input
3-6-55
2AD Terminals (CN) 1-B13 1-B14 1-B15 2-1 1-B7 1-B7 1-B7 2-2 Voltage 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 5 V DC Remarks MCPCB1, 2 image control signal DATA5, input MCPCB1, 2 image control signal DATA6, input MCPCB1, 2 image control signal DATA7, input 5 V DC supply for MCPCB1, 2, input
3-6-56
IC1 CN9 C165 C168 L84 C166 L86 CN8 C162 C161 C160 C45 C69 TR1 TR2 TR3 TR4 TR5 TR6 CN4
CN1
CN3
CN2
C167
TR8 TR9
TR10
IC10
IC11
IC12
IC13
IC2 D1 L81 C20 C23 C122 C152 L85 C169 IC15 C159 C170 TP3 TP4 RA3 RA4 RA1 RA2 RA5 RA17 C107 RA18 RA19 C155 C154 C93 C96 TP5 TP6 IC17 IC14 C113 C31 C32
IC3
C46 C50 RA8 TP7 RA6 RA7 C158 C157 TP8 RA22 RA24 RA25 RA26 RA27 RA28 C66 RA9 RA10 RA11 RA12 C67 IC18
IC8
IC9
IC20
C84
IC22
TP10
IC21
RA13
TP9
X1
RA33
RA34
RA35
RA36
RA38
RA39
RA40
C153
IC26 IC25
IC27
RA30 IC28
RA41
IC16
C108
RA31 RA32
RA37
IC30
CN7
3-6-57
2AD-1 2AD
2AD Terminals (CN) 1-2 1-3 1-4 1-5 1-6 1-7 1-9 1-10 1-11 1-12 2-2 2-3 2-4 2-7 2-8 2-9 2-10 2-11 2-12 3-1 3-2 3-3 3-4 3-5 3-6 3-7 3-8 3-9 3-10 3-11 4-1 4-2 4-3 4-4 4-5 4-14 4-14 4-14 4-14 4-14 4-14 4-14 4-14 4-14 4-14 4-14 4-14 4-14 4-14 4-14 4-14 4-14 4-14 4-14 4-14 4-14 4-14 4-14 4-14 4-14 4-14 4-14 4-14 4-14 4-14 4-14 4-14 4-14 4-14 4-14 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC Voltage 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 5/0 V DC 5/0 V DC 5/0 V DC 5/0 V DC 0/5 V DC 0/5 V DC (pulse) 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC (pulse) 0/5 V DC Remarks OSLED (red) on/off, output OSLED (green) on/off, output SBPSOL release signal, output SBPSOL latch-on signal, output OFCL on/off, output EFSSOL on/off, output SBFSSOL on/off, output OFSOL release signal, output OFSOL latch-on signal, output OFM enable signal, output OSBSW on/off, input OFSW on/off, input OSSW on/off, input SRDF installed/not installed signal, input OSWSW on/off, input DFSSW2 off/on, input DFSSW1 off/on, input OSLSW off/on, input DFTSW off/on, input OFM control signal OFM RET, output OFM drive clock pulse, output OFM rotation direction switching signal OFM CWB, output OCM enable signal, output OCM control signal OCM RET, output OCM drive clock pulse, output OCM rotation direction switching signal OCM CWB, output OCM current control voltage OCM Vref, output OCM drive control signal OCM M3, output OCM drive control signal OCM M2, output OCM drive control signal OCM M1, output ODSW on/off, input SM current control voltage SM Vref, output SM drive control signal SM M1, output SM drive control signal SM M2, output SM drive control signal SM M3, output
3-6-58
2AD Terminals (CN) 4-6 4-7 4-8 4-9 4-10 4-11 4-12 4-13 5-4 5-5 5-6 5-7 5-8 5-9 5-10 5-11 6-3 6-4 6-5 6-6 6-7 7-A1 7-A2 7-A3 7-A5 7-A6 7-A7 7-A8 7-A10 7-B1 7-B2 7-B3 7-B5 7-B6 7-B7 4-14 4-14 4-14 4-14 4-14 4-14 4-14 4-14 5-1, -2 5-1, -2 5-1, -2 5-1, -2 5-1, -2 5-1, -2 5-1, -2 5-1, -2 6-1, -2 6-1, -2 6-1, -2 6-1, -2 6-1, -2 7-A4 7-A4 7-A4 7-A4 7-A9 7-A9 7-A9 7-A9 7-B4 7-B4 7-B4 7-B4 7-B9 7-B9 0/5 V DC 5 V DC 0/5 V DC (pulse) 0/5 V DC 0/5 V DC 5 V DC 0/5 V DC (pulse) 0/5 V DC 0/5 V DC 5 V DC 0/5 V DC (pulse) 0/5 V DC 0/5 V DC 5 V DC Voltage 0/5 V DC 0/5 V DC 0/5 V DC (pulse) 0/5 V DC 0/5 V DC 0/5 V DC 5/0 V DC 5/0 V DC 5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 12 V DC Remarks SM drive control signal SM M4, output SM drive control signal SM M5, output SM drive clock pulse, output SM rotation direction switching signal SMOT CWB, output SM control signal SMOT RET, output SM enable signal, output EL on/off, output SHPSW on/off, input 5 V DC supply for CCDPCB, output CCD drive clock signal SHIFT , output CCD drive clock signal SHIFT +, output CCD drive clock signal CLP , output CCD drive clock signal CLP +, output CCD drive clock signal RS , output CCD drive clock signal RS +, output CCD drive clock signal CLK , output CCD drive clock signal f CLK +, output +12 V DC supply for CCDPCB, output CCD control signal VO_E , input CCD control signal VO_E +, input CCD control signal VO_O , input CCD control signal VO_O +, input OSD1, 2 LED emission selection, output 5 V DC supply for OSD1, 2, output OSD1, 2 sensor drive pulse, output OSD1, 2 detection data, input OSD3, 4 LED emission selection, output 5 V DC supply for OSD3, 4, output OSD3, 4 sensor drive pulse, output OSD3, 4 detection data, input OSD5, 6 LED emission selection, output 5 V DC supply for OSD5, 6, output OSD5, 6 sensor drive pulse, output OSD5, 6 detection data, input OSD7*, 8* LED emission selection, output 5 V DC supply for OSD7*, 8*, output
3-6-59
2AD Terminals (CN) 7-B8 7-B10 8-1 8-3 8-4 8-5 8-7 8-8 8-9 8-10 8-11 8-12 8-13 8-14 8-15 8-16 8-17 8-18 8-19 8-20 8-21 8-23 8-24 8-25 8-26 8-27 8-28 8-29 8-30 8-31 8-32 8-33 8-34 7-B9 7-B9 8-2 8-6 8-2 8-6 8-6 8-6 8-6 8-6 8-22 8-22 8-22 8-22 8-22 8-22 8-22 8-22 8-22 8-22 8-22 8-22 8-22 8-22 8-22 8-22 8-22 8-22 8-22 8-22 8-22 8-22 8-22 Voltage 0/5 V DC (pulse) 0/5 V DC 0/5 V DC 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC 0/5 V DC (pulse) 0/5 V DC 0/5 V DC (pulse) 0/5 V DC 0/5 V DC (pulse) 0/5 V DC 0/5 V DC (pulse) 0/5 V DC 0/5 V DC (pulse) 0/5 V DC 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC 0/5 V DC (pulse) 0/5 V DC 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) Remarks OSD7*, 8* sensor drive pulse, output OSD7*, 8* detection data, input SCPCB RESET SCN signal, input SCPCB image control signal SID7 , output SCPCB serial communication signal, input SCPCB image control signal SID7 +, output SCPCB image control signal SID6 , output SCPCB serial communication signal, output SCPCB image control signal SID6 +, output SCPCB SCAN START signal, input SCPCB image control signal SID5 , output SCPCB ENGAKU SCN signal, input SCPCB image control signal SID5 +, output SCPCB ENG HEADER SCN signal, input SCPCB image control signal SID4 , output SCPCB SC TIM signal, output SCPCB image control signal SID4 +, output SCPCB SCN ACK signal, output SCPCB image control signal SID3 , output SCPCB SCN HEADER signal, output SCPCB image control signal SID3 +, output SCPCB image control signal SID2 , output SCPCB clock pulse , output SCPCB image control signal SID2 +, output SCPCB clock pulse +, output SCPCB image control signal SID1 , output SCPCB SMRE signal, output SCPCB image control signal SID1 +, output SCPCB SMRE + signal, output SCPCB image control signal SID0 , output SCPCB SOVSYNC signal, output SCPCB image control signal SID0 +, output SCPCB SOVSYNC + signal, output
3-6-60
CN4 3 J10 J4 + JP10 JP13 E C B DT2 L5 JP9 1 2 CN3 5 6 C23 J16 J17 J9 C21 JP11 JP14 JP12 1 CN5 3 R15 R16 JP7 JP8 C19 IC1 R17 C20 C7 R8 C8 R9 C9 JP2 JP4 J5 14 + + 1 C11 JP1 JP3 C10 C5 C4 R11 R10 C16 +
TP1
J12
J7
J11 L2 C17 C18 C15 C14 JP5 JP15 JP6 JP16 L3 J6 J3 1 CN2 6 R14 1 L4 R13 R2 R3 R4 R5 R6 C6 C13
3-6-61
2AD Terminals (CN) 1-2 1-3 1-4 1-5 1-6 1-7 1-8 1-9 1-10 1-11 1-12 1-13 1-14 2-1 2-2 2-3 2-4 2-5 2-6 3-1 3-2 3-3 3-4 4-1 4-2 5-1 5-2 6-2 6-4 1-1 1-1 1-1 1-1 1-1 1-1 1-1 1-1 1-1 1-1 1-1 1-1 1-1 3-5, -6 3-5, -6 3-5, -6 3-5, -6 3-5, -6 3-5, -6 3-5, -6 3-5, -6 3-5, -6 3-5, -6 4-3 4-3 5-3 5-3 6-1 6-3 0/5 V DC 0/5 V DC (pulse) 24 V DC 0/5 V DC (pulse) 0/5 V DC (pulse) 24 V DC 0/5 V DC (pulse) 0/5 V DC 0/5 V DC 24 V DC 24 V DC 5 V DC 0/5 V DC 5 V DC 0/5 V DC 24 V DC 5 V DC Voltage 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC (pulse) 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC EL on/off, input SM enable signal, input SM control signal SMOT RET, input SM rotation direction switching signal SMOT CWB, input SM drive clock pulse, input SM drive control signal SM M5, input SM drive control signal SM M4, input SM drive control signal SM M3, input SM drive control signal SM M2, input SM drive control signal SM M1, input SM current control voltage SM Vref, input ODSW on/off, output SM coil energization pulse, output (B_) 24 V DC supply for SM, output SM coil energization pulse, output (B) SM coil energization pulse, output (A) 24 V DC supply for SM, output SM coil energization pulse, output (A_) EL on/off, output EL on/off, output 24 V DC supply for INPCB, output 24 V DC supply for INPCB, output 5 V DC supply for SHPSW, output SHPSW on/off, input 5 V DC supply for ODSW, output ODSW on/off, input 24 V DC supply for SMPCB, input 5 V DC supply for SMPCB, input Remarks SHPSW on/off, output
3-6-62
C1
R2
E C B TR1
R4 C11
R5 R6 R7
9 C2
R12 R13 R15 R16 R17 F8
F1
F2 F3 F4
9 IC3
C17
R25
C3
C4
5
C6
C5
F5
RA1
C8 R8
C7
1 IC5
R32 R31
C9 C23
CN2 7
3-6-63
2AD Terminals (CN) 1-1 1-2 1-3 1-4 1-5 1-6 1-7 1-8 1-9 2-1 2-2 2-3 2-4 2-5 Voltage Remarks CCD drive clock signal CLK +, input CCD drive clock signal CLK , input CCD drive clock signal RS +, input CCD drive clock signal RS , input CCD drive clock signal CLP +, input CCD drive clock signal CLP , input CCD drive clock signal SHIFT +, input CCD drive clock signal SHIFT , input 5 V DC supply for CCDPCB, input CCD control signal VO_O +, output CCD control signal VO_O , output CCD control signal VO_E +, output CCD control signal VO_E , output 12 V DC +12 V DC supply for CCDPCB, input
1-10, -11 0/5 V DC 1-10, -11 0/5 V DC 1-10, -11 0/5 V DC 1-10, -11 0/5 V DC 1-10, -11 0/5 V DC 1-10, -11 0/5 V DC 1-10, -11 0/5 V DC 1-10, -11 0/5 V DC 1-10, -11 5 V DC 2-6, -7 2-6, -7 2-6, -7 2-6, -7 2-6, -7
3-6-64
A-13
A-13
B-1
B-1
CN5
CN6
CN4
B-15 A-1
B-13
A-1
CN1
10 9
CN2
22 21 2 1 14 13
CN3
2 1
Terminals (CN) 1-1 1-2 1-7 1-8 2-1 2-2 2-3 2-6 2-7 2-8 2-9 2-10 2-11 2-12 2-13 1-3, -4 1-3, -4 1-9, -10 1-9, -10 1-9, -10 1-9, -10 1-9, -10 1-9, -10 1-9, -10 1-9, -10 1-9, -10 1-9, -10 1-9, -10 1-9, -10 1-9, -10
Remarks 24 V DC supply, input 24 V DC supply, input 5 V DC supply, input 5 V DC supply, input OCM control signal OCM M1, input OCM control signal OCM M2, input OCM control signal OCM M3, input OCM current control voltage OCM Vref, input
OCM rotation direction switching signal OCM CWB, input OCM drive clock pulse, input OCM control signal OCM RET, input OCM enable signal, input OFM rotation direction switching signal OFM CWB, input OFM drive clock pulse, input OFM control signal OFM RET, input
2 1
3-6-65
2AD Terminals (CN) 2-14 2-15 2-16 2-17 2-19 2-20 2-21 2-22 3-1 3-2 3-3 3-4 3-5 3-6 3-7 3-8 3-9 3-10 3-11 4-3 4-4 5-A1 5-A2 5-A3 5-A4 5-A5 5-A6 5-A7 5-A8 5-A9 5-A10 5-A11 5-A12 5-A13 1-9, -10 1-9, -10 1-9, -10 1-9, -10 1-9, -10 1-9, -10 1-9, -10 1-9, -10 1-9, -10 1-9, -10 1-9, -10 1-9, -10 1-9, -10 1-9, -10 1-9, -10 1-9, -10 1-9, -10 1-9, -10 1-9, -10 4-2 4-2 1-3, -4 1-3, -4 1-3, -4 1-3, -4 1-3, -4 1-3, -4 1-3, -4 1-3, -4 1-3, -4 1-3, -4 1-3, -4 1-3, -4 1-3, -4 0/5 V DC 0/5 V DC 0/5 V DC 0/24 V DC 0/24 V DC 0/24 V DC 0/24 V DC 0/24 V DC 24 V DC 0/24 V DC 24 V DC 0/24 V DC 24 V DC 24 V DC 0/24 V DC (pulse) 0/24 V DC (pulse) 0/24 V DC (pulse) 0/24 V DC (pulse) Voltage 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC Remarks OFM enable signal, input OFSOL latch-on signal, input OFSOL release signal, input SBFSSOL on/off, input EFSSOL on/off, input OFCL on/off, input SBPSOL latch-on signal, input SBPSOL release signal, input OSSW on/off, output OFSW on/off, output OSBSW on/off, output DFTSW on/off, output OSLSW on/off, output DFSSW1 on/off, output DFSSW2 on/off, output Size detection voltage, output OSLED (green) off/on, input OSLED (red) off/on, input SRDF installed/not installed signal DFSSW1 on/off, output DFSSW2 on/off, output 24 V DC supply for SBPSOL, output SBPSOL latch-on signal, output SBPSOL release signal, output 24 V DC supply for OFCL, output OFCL on/off, output 24 V DC supply for EFSSOL, output EFSSOL on/off, output 24 V DC supply for OCM, output (A) 24 V DC supply for OCM, output (B) OCM motor coil energization pulse, output (A) OCM motor coil energization pulse, output (B) OCM motor coil energization pulse, output (A_) OCM motor coil energization pulse, output (B_)
3-6-66
2AD Terminals (CN) 5-B1 5-B2 5-B3 5-B4 5-B5 5-B6 5-B7 5-B8 5-B11 5-B12 5-B13 6-A5 6-A6 6-A8 6-A9 6-A11 6-A12 6-A14 6-A15 6-B1 6-B2 6-B4 6-B5 6-B7 6-B9 1-3, -4 1-3, -4 1-3, -4 1-3, -4 1-3, -4 1-3, -4 1-3, -4 1-3, -4 1-3, -4 1-3, -4 1-3, -4 6-A4 6-A4 6-A7 6-A7 6-A10 6-A10 6-A13 6-A13 6-B3 6-B3 6-B6 6-B6 6-B8 6-B8 Voltage 24 V DC 24 V DC 0/24 V DC (pulse) 0/24 V DC (pulse) 0/24 V DC (pulse) 0/24 V DC (pulse) 24 V DC 0/24 V DC 24 V DC 0/24 V DC 0/24 V DC 0/5 V DC 5 V DC 0/5 V DC 5 V DC 0/5 V DC 5 V DC 0/5 V DC 5 V DC 5 V DC 0/5 V DC 5 V DC 0/5 V DC 0/5 V DC 0/5 V DC Remarks 24 V DC supply for OFM, output (A) 24 V DC supply for OFM, output (B) OFM motor coil energization pulse, output (A) OFM motor coil energization pulse, output (B) OFM motor coil energization pulse, output (A_) OFM motor coil energization pulse, output (B_) 24 V DC supply for SBFSSOL, output SBFSSOL on/off, output 24 V DC supply for OFSOL, output OFSOL latch-on signal, output OFSOL release signal, output OSBSW on/off, input 5 V DC supply for OSBSW, output OSWSW on/off, input 5 V DC supply for OSWSW, output OSLSW on/off, input 5 V DC supply for OSLSW, output DFTSW on/off, input 5 V DC supply for DFTSW, output 5 V DC supply for OSSW, output OSSW on/off, input 5 V DC supply for OFSW, output OFSW on/off, input OSLEDPCB (red) on/off, output OSLEDPCB (green) on/off, output
3-6-67
IC2 1 3
8 IC3 1 1 C11
L17
L22
4 CN5 +
C14
17
CN3
IC4
C26
2 1 1 2 10 IC9 30 1 IC10 RA3 RA4 RA5 RA6 RA7 IC12 IC16 1 1 8 C 8 L47 D6 L48 TR4 D5 C C CB E E TR3 RA2 RA1 51 50
IC7
C25
IC8
+ C TR2
C29 31 1
B E
13 14
IC11
18 17
CN1
8 B E C TR5 D8 D7 C C X1 L49 1 2 10 100 B E TR8 1 C TR6 L50 4 CN4 1 IC18 IC19 31 30 1 IC20
15
IC21
1 2
CN2
3-6-68
2AD-1 2AD
100
81
80
2AD Terminals (CN) 1-1 1-2 1-3 1-4 1-5 1-6 1-7 1-9 1-10 1-11 1-12 1-14 2-1 2-2 2-4 2-5 2-6 2-7 2-8 2-9 2-10 2-11 2-12 2-13 2-14 2-15 2-16 2-17 3-1 3-2 3-3 3-4 3-5 1-8 2-3 1-8 1-8 1-8 1-8 2-3 1-8 1-8 1-8 1-8 1-8 2-3 2-3 2-3 1-8 1-8 1-8 1-8 1-8 1-8 1-8 1-8 1-8 1-8 1-8 1-8 1-8 6-2 6-2 6-2 6-2 6-2 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC 5 V DC 5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC (pulse) Voltage 0/5 V DC 23 V DC 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 23 V DC 5 V DC 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC 24 V DC 23 V DC Remarks LCD control voltage, output 23 V supply for LCD, output LCD (XD3) data, output LCD (XD2) data, output LCD (XD1) data, output LCD (XD0) data, output 23 V supply for LCD, output 5 V DC supply for LCD, output LCD control signal XSCL, output LCD control signal LP, output LCD control signal DIN, output LCD control signal LCD REM, output 24 V DC supply for OLPCB, output 23 V DC supply for OLPCB, output OLPCB contrast adjustment VR supply, output OLPCB key return signal DIGKEY L1, input OLPCB key return signal DIGKEY L2, input OLPCB key return signal DIGKEY L3, input OLPCB scan signal SCAN L1, output OLPCB scan signal SCAN L2, output OLPCB scan signal SCAN L3, output OLPCB LED on DIG LED L1, output OLPCB LED on DIG LED L2, output OLPCB LED on DIG LED L3, output OLPCB LED on DIG LED L4, output OLPCB CFL on/off, output 5 V DC supply for OLPCB, output 5 V DC supply for OLPCB, output ORPCB key return signal DIGKEY R1, input ORPCB key return signal DIGKEY R2, input ORPCB key return signal DIGKEY R3, input ORPCB key return signal DIGKEY R4, input ORPCB scan signal SCAN R1, output
3-6-69
2AD Terminals (CN) 3-6 3-7 3-8 3-9 3-10 3-11 3-12 3-14 4-1 4-2 4-3 4-4 5-3 5-4 6-3 6-4 6-5 6-6 6-7 6-9 6-10 6-2 6-2 6-2 6-2 6-2 6-2 6-2 6-2 6-2 6-2 6-2 6-2 5-2 5-1 6-2 6-2 6-8 6-8 6-8 6-8 6-11 Voltage 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC 5 V DC 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 0/5 V DC (pulse) 5 V DC 24 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC 0/5 V DC (pulse) 0/5 V DC 0/5 V DC (pulse) Remarks ORPCB scan signal SCAN R2, output ORPCB scan signal SCAN R3, output ORPCB scan signal SCAN R4, output ORPCB LED on DIG LED R1, output ORPCB LED on DIG LED R2, output ORPCB LED on DIG LED R3, output ORPCB BZ1 on/off, output 5 V DC supply for ORPCB, output Touch panel detection voltage Y2, output Touch panel detection voltage X1, input Touch panel detection voltage Y1, input Touch panel detection voltage X2, output 5 V DC supply for OMPCB, input 24 V DC supply for OMPCB, input OMPCB RESET MMI signal, input OMPCB ENG ERROR MMI signal, input OMPCB MMI ERROR signal, output OMPCB ENGACK MMI signal, input OMPCB serial communication signal, output OMPCB MMI ACK signal, output OMPCB serial communication signal, input
3-6-70
TP31 WR OSC1 1
CN13 2 CN9 1
CN3 4
27C256
1 TP12 TP24 TP22 TP11 BCL P1 Rxd R SEN TP13 TP4 EMP RCL TP23 TP16 + P2 TP25 TP2 PP51 +5 V Txd TP1 TP18 PP50 SG + RS2 RS1 TP9 IC7 PD78233GC-389 LMS2 TP3 PP52 TP5 SIZ K C19 DA1 K TP7 LMS1 TP8 LS2 C17 D4 TP21 E1 TP20 E2 D2 TP27 E1CLK TP26 E2CLK + 1 CN2 6 1 CN7 10 3 CN6 1 TP30 MOT PWM TP6 LS1 DA2 ZD1
IC2
C14
CN1
CN4
M5248P
PF4065K500A
11
B C E + Q1 B C E Q3 Q2 B C E Q4
B C E
MADE IN JAPAN
WARNING
TP19 MOT CLK TP10 CLK +
FOR CONTINUED PROTECTION AGAINST RISK OF FIRE. REPLACE ONLY WITH SAME TYPE AND RATING OF FUSE
SEC-A
C18
CN12
C16
12
3-6-71
2AD
2AD Terminals (CN) 1-1 1-4 1-5 1-6 1-7 1-8 1-9 1-10 1-11 2-3 2-6 3-1 3-3 4-1 4-2 4-4 4-5 4-6 4-7 4-9 4-11 7-1 7-2 7-3 7-4 7-5 7-7 7-8 7-10 9-1 9-3 9-5 1-1 4-8 4-8 4-8 4-8 4-8 4-8 4-8 4-8 2-2 2-5 3-2 3-4 4-8 4-8 4-8 4-8 4-8 4-8 4-8 4-8 7-6, -9 7-6, -9 7-6, -9 7-6, -9 7-6, -9 7-6, -9 7-6, -9 7-6, -9 9-2 9-4 9-2, -4 Voltage 5/0 V DC (pulse) 24/0 V DC 2/0 (pulse)/0 V DC 2/0 (pulse)/0 V DC 5/0 V DC 5/0 V DC 5/0 V DC 5/0 V DC 2/0 (pulse)/0 V DC 5/0 V DC 5/0 V DC 5 V DC 24 V DC 24 V DC 24 V DC 24/0 V DC 24/0 V DC 24/0 V DC 5 V DC 2/0 (pulse)/0 V DC 5/0 V DC 24/0 V DC 24 V DC 24 V DC 24/0 V DC 1.1 V DC 5/0 V DC 1.1 V DC 5/0 V DC 5/0 V DC (pulse) 5/0 V DC (pulse) 0/5 V DC Remarks Clock signal for PPSENS1 - 3 and PESENS, output DOSSW signal on/off, input PESENS signal input, paper present/ absent, input PPSENS2 signal input, paper present/ absent, input DLSW1 on/off, input UPSW1 on/off, input DLSW2 on/off, input UPSW2 on/off, input PPSENS3 paper present/absent, input PLDSENS1 on/off, input PLDSENS2 on/off, input 5 V DC supply, input 24 V DC supply, input Power supply for RCL, PFCL1, PFCL2 and CCL, output Power supply for RCL, PFCL1, PFCL2 and CCL, output PFCL1 off/on, output PFCL2 off/on, output CCL off/on, output Power supply for PPSENS1 - 3, PESENS, SCSW, UPSW1 - 2 and DLSW1 - 2, output PPSENS1 paper present/absent, input SCSW on/off, input PDM1 off/on, output Power supply for PDM1, output Power supply for PDM2, output PDM2 off/on, output Power supply for PDMSENS1, output PDMSENS1 on/off, input Power supply for PDMSENS2, output PDMSENS2 on/off, input Serial data signal to EPCB (TXD) Serial data signal from EPCB (RXD) PFSW4 on/off, input
3-6-72
2AD Terminals (CN) 12-1 12-3 12-4 12-5 12-2 12-2 12-2 12-2 Voltage 24 V DC 5/0 V DC (pulse) 5 V DC 5/0 V DC (pulse) Remarks Power supply for CM, output CM drive PWM signal, output Power supply for CM, output CM FG signal, input
3-6-73
2AD
Check for continuity. If none, replace the cord. Check for continuity across the contacts. If none, replace the main switch. Check for continuity. If none, remove the cause of blowing and replace the fuse. Check for continuity across the contacts of each switch. If none, replace the switch. With AC present, check for 5 V DC at CN2-1 on the power source PCB, 12 V DC at CN4-1 and 24 V DC at CN1-1. If none, replace the power source PCB. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Check visually and replace the drive motor if necessary.
Poor contact in the drive motor connector terminals. Broken drive motor gear.
3-6-74
2AD Problem (2) The drive motor does not operate (C200). Causes Defective drive motor. Check procedures/corrective measures Run maintenance item U030 and check if the drive motor operates when CN12-B4 on the engine PCB goes low. If not, replace the drive motor. Run maintenance item U030 and check if CN1-113 on the main PCB goes low. If not, replace the main PCB. Check for continuity across the coil. If none, replace the scanner motor. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Check if the motor drive coil energization pulse signals are output at CN4-3, CN4-4, CN4-5, CN4-6 and CN4-7 on the scanner control PCB when maintenance item U073 is run. If not, replace the scanner control PCB. Check for continuity across the coil. If none, replace the upper lift motor. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Check if 24 V DC is output across CN8-A2 and CN8-A3 on the engine PCB right after the upper drawer is installed. If not, replace the engine PCB. Check for continuity across the coil. If none, replace the lower lift motor. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Check if 24 V DC is output across CN8-A4 and CN8-A5 on the engine PCB right after the lower drawer is installed. If not, replace the engine PCB.
Defective main PCB. Broken scanner motor coil. Poor contact in the scanner motor connector terminals. Defective scanner control PCB.
Broken upper lift motor coil. Poor contact in the upper lift motor connector terminals. Defective engine PCB.
Broken lower lift motor coil. Poor contact in the lower lift motor connector terminals. Defective engine PCB.
3-6-75
2AD Problem (6) The toner feed motor does not operate. Causes Broken toner feed motor coil. Poor contact in the toner feed motor connector terminals. Defective engine PCB. Check procedures/corrective measures Check for continuity across the coil. If none, replace the toner feed motor. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Run maintenance item U135 and check if drive pulse signal is output across CN2-A5 and CN2-A6 on the engine PCB. If not, replace the engine PCB. Check for continuity across the coil. If none, replace the paper conveying section fan motor. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
(7) The paper conveying section fan motor does not operate.
Broken paper conveying section fan motor coil. Poor contact in the paper conveying section fan motor connector terminals. Defective engine PCB.
Run maintenance item U030. If 24 V DC is always present at CN8-B7 on the engine PCB, replace the engine PCB. Check for continuity across the coil. If none, replace cooling fan motor 1. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Run maintenance item U030 and check if CN3-B4 on the engine PCB goes low. If not, replace the engine PCB. Check for continuity across the coil. If none, replace cooling fan motor 2. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Run maintenance item U030 and check if CN3-B6 on the engine PCB goes low. If not, replace the engine PCB.
(8) Cooling fan motor 1 does not operate at all or does not turn at full speed.
Broken cooling fan motor 1 coil. Poor contact in the cooling fan motor 1 connector terminals. Defective engine PCB.
(9) Cooling fan motor 2 does not operate at all or does not turn at full speed.
Broken cooling fan motor 2 coil. Poor contact in the cooling fan motor 2 connector terminals. Defective engine PCB.
3-6-76
2AD Problem (10) Paper feed motor does not operate (C230). Causes Broken paper feed motor coil. Poor contact in the paper feed motor connector terminals. Defective paper feed motor. Check procedures/corrective measures Check for continuity across the coil. If none, replace the paper feed motor. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Check if the paper feed motor rotates when CN11-3 on the engine PCB goes low while maintenance item U030 is run. If not replace the paper feed motor. Run maintenance item U030 and check if CN1-87 on the main PCB goes low. If not, replace the main PCB. Check for continuity across the coil. If none, replace the paper conveying motor. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Check if the paper feed motor rotates when CN5-A8 on the engine PCB goes low while maintenance item U030 is run. If not, replace the paper conveying motor. Run maintenance item U030 and check if CN1-111 on the main PCB goes low. If not, replace the main PCB. Check for continuity across the coil. If none, replace the toner recycle motor. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Run maintenance item U135 and check if drive pulse signal is output across CN2-A7 and CN2-A8 on the engine PCB. If not, replace the engine PCB.
Defective main PCB. Broken paper conveying motor coil. Poor contact in the paper conveying motor connector terminals. Defective paper feed motor.
Defective main PCB. (12) The toner recycle motor does not operate. Broken toner recycle motor coil. Poor contact in the toner recycle motor connector terminals. Defective engine PCB.
3-6-77
2AD Problem (13) The charger cleaning motor does not operate. Causes Broken charger cleaning motor coil. Poor contact in the charger cleaning motor connector terminals. Defective engine PCB. (14) The image formation unit fan motor does not operate. Broken image formation unit fan motor coil. Poor contact in the image formation unit fan motor connector terminals. Defective engine PCB. (15) The upper paper feed clutch does not operate. Broken upper paper feed clutch coil. Poor contact in the upper paper feed clutch connector terminals. Defective engine PCB. Check procedures/corrective measures Check for continuity across the coil. If none, replace the charger cleaning motor. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Run maintenance item U102 and check if CN8-B4 and CN8-B5 on the engine PCB go low. If not, replace the engine PCB. Check for continuity across the coil. If none, replace the image formation unit fan motor. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
Run maintenance item U135 and check if CN2-A4 on the engine PCB goes low. If not, replace the engine PCB. Check for continuity across the coil. If none, replace the upper paper feed clutch. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Run maintenance item U032 and check if CN15-13 on the engine PCB goes low. If not, replace the engine PCB.
3-6-78
2AD Problem (16) The lower paper feed clutch does not operate. Causes Broken lower paper feed clutch coil. Poor contact in the lower paper feed clutch connector terminals. Defective engine PCB. (17) Feed clutch 1 does not operate. Broken feed clutch 1 coil. Poor contact in feed clutch 1 connector terminals. Defective engine PCB. (18) Feed clutch 2 does not operate. Broken feed clutch 2 coil. Poor contact in feed clutch 2 connector terminals. Defective engine PCB. (19) Feed clutch 3 does not operate. Broken feed clutch 3 coil. Poor contact in feed clutch 3 connector terminals. Defective engine PCB. Check procedures/corrective measures Check for continuity across the coil. If none, replace the lower paper feed clutch. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Run maintenance item U032 and check if CN15-14 on the engine PCB goes low. If not, replace the engine PCB. Check for continuity across the coil. If none, replace feed clutch 1. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Run maintenance item U032 and check if CN12-A4 on the engine PCB goes low. If not, replace the engine PCB. Check for continuity across the coil. If none, replace feed clutch 2. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Run maintenance item U032 and check if CN12-A8 on the engine PCB goes low. If not, replace the engine PCB. Check for continuity across the coil. If none, replace feed clutch 3. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Run maintenance item U032 and check if CN12-A10 on the engine PCB goes low. If not, replace the engine PCB.
3-6-79
2AD Problem (20) Feed clutch 4 does not operate. Causes Broken feed clutch 4 coil. Poor contact in feed clutch 4 connector terminals. Defective engine PCB. (21) Feed clutch 5 does not operate. Broken feed clutch 5 coil. Poor contact in feed clutch 5 connector terminals. Defective engine PCB. (22) The registration clutch does not operate. Broken registration clutch coil. Poor contact in the registration clutch connector terminals. Defective engine PCB. (23) The bypass paper feed clutch does not operate. Broken bypass paper feed clutch coil. Poor contact in the bypass paper feed clutch connector terminals. Defective engine PCB. Check procedures/corrective measures Check for continuity across the coil. If none, replace feed clutch 4. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Run maintenance item U032 and check if CN8-B9 on the engine PCB goes low. If not, replace the engine PCB. Check for continuity across the coil. If none, replace feed clutch 5. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Run maintenance item U032 and check if CN12-A2 on the engine PCB goes low. If not, replace the engine PCB. Check for continuity across the coil. If none, replace the registration clutch. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Run maintenance item U032 and check if CN8-B11 on the engine PCB goes low. If not, replace the engine PCB. Check for continuity across the coil. If none, replace the bypass paper feed clutch. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Run maintenance item U032 and check if CN14-A7 on the engine PCB goes low. If not, replace the engine PCB.
3-6-80
2AD Problem (24) The eject speed switching clutch does not operate. Causes Broken eject speed switching clutch coil. Poor contact in the eject speed switching clutch connector terminals. Defective engine PCB. (25) The bypass solenoid does not operate. Broken bypass solenoid coil. Poor contact in the bypass solenoid connector terminals. Defective engine PCB. (26) The cleaning lamp does not turn on. Poor contact in the cleaning lamp connector terminals. Defective cleaning lamp. Defective engine PCB. (27) The exposure lamp does not turn on. Poor contact in the exposure lamp connector terminals. Defective inverter PCB. Defective scanner motor PCB. Check procedures/corrective measures Check for continuity across the coil. If none, replace the eject speed switching clutch. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
Run maintenance item U032 and check if CN3-A11 on the engine PCB goes low. If not, replace the engine PCB. Check for continuity across the coil. If none, replace the bypass solenoid. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Run maintenance item U033 and check if CN14-A8 on the engine PCB goes low. If not, replace the engine PCB. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Check for one-way continuity across each LED comprising the cleaning lamp. If none, replace the cleaning lamp. If the cleaning lamp turns on when CN2-A2 on the engine PCB is held low, replace the engine PCB. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. If the exposure lamp does not turn on when CN1-5 and CN1-6 on the inverter PCB are held low, replace the inverter PCB. If the exposure lamp turns on when CN3-1 and 3-2 on the scanner motor PCB are held low, replace the scanner motor PCB.
3-6-81
2AD Problem (28) The exposure lamp does not turn off. Causes Defective inverter PCB. Defective scanner motor PCB. Broken wire in fixing heater M or S. Fixing unit thermostat 1 or 2 triggered. Broken fixing unit thermistor wire. (30) Fixing heater M or S does not turn off (fixing unit thermostat 1/ 2 triggered; C620). (31) Main charging is not performed (C510). Dirty sensor part of the fixing unit thermistor. Defective engine PCB. Check procedures/corrective measures If the exposure lamp does not turn off with CN1-5 and CN1-6 on the inverter PCB high, replace the inverter PCB. If CN3-1 and CN3-2 on the scanner motor PCB are always low, replace the scanner motor PCB. Check for continuity across each heater. If none, replace the heater (see page 3-3-62). Check for continuity across each thermostat. If none, remove the cause and replace the thermostat. Measure the resistance. If it is , replace the fixing unit thermistor. Check visually and clean the thermistor sensor parts. If fixing heater M/S stays on while CN6-7 and CN6-8 on the engine PCB go high, replace the engine PCB.
Broken main charger wire. Leaking main charger housing. Poor contact in the high-voltage transformer PCB connector terminals. Defective main PCB. Defective engine PCB. Defective highvoltage transformer PCB.
3-6-82
2AD Problem (32) Transfer charging is not performed (C511). Causes Broken transfer charger wire. Poor contact in the high-voltage transformer PCB connector terminals. Defective main PCB. Defective engine PCB. Defective highvoltage transformer PCB. (33) Separation charging is not performed (C511). Broken separation charger wire. Poor contact in the high-voltage transformer PCB connector terminals. Defective highvoltage transformer PCB. Replace the separation charger wire (see page 3-3-54). Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Check procedures/corrective measures See page 3-6-3.
Run maintenance item U101. If separation charging does not take place while CN1-9 on the high-voltage transformer PCB goes low, replace the high-voltage transformer PCB. Run maintenance item U101 and check if CN5-B5 on the engine PCB goes low. If not, replace the engine PCB. Check the developing bias wire. If there is any problem, replace it. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Check if the developing bias is output when CN1-4 on the high-voltage transformer PCB goes low while maintenance item U030 is run. If not, replace the high-voltage transformer PCB.
Defective engine PCB. (34) No developing bias is output. Poor contact in the developing bias wire. Poor contact in the high-voltage transformer PCB connector terminals. Defective highvoltage transformer PCB.
3-6-83
2AD Problem (34) No developing bias is output. (35) The original size is not detected. (36) The original size is not detected correctly. Causes Defective engine PCB. Check procedures/corrective measures Check if CN5-B10 on the engine PCB goes low during copying. If not, replace the engine PCB. If the level of CN5-2 on the scanner motor PCB does not change when the original detection switch is turned on and off, replace the original detection switch. Check the original and correct if necessary. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Check if each sensor operates correctly. If not, replace it or, if necessary, the scanner control PCB. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. If any keys do not work after the touch panel has been initialized, replace the touch panel or operation unit main PCB. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Check if CN15-9 on the engine PCB goes low when the upper paper switch is turned on with 5 V DC present at CN15-7 on the engine PCB. If not, replace the upper paper switch.
Original is not placed correctly. Poor contact in the original size sensors connector terminals. Defective original size sensors or the scanner control PCB.
Poor contact in the touch panel connector terminals. Defective touch panel or operation unit main PCB. Poor contact in the upper paper switch connector terminals. Defective upper paper switch.
(38) The message requesting paper to be loaded is shown when paper is present in the upper drawer.
3-6-84
2AD Problem (39) The message requesting paper to be loaded is shown when paper is present in the lower drawer. (40) The message requesting paper to be loaded is shown when paper is present on the bypass table. (41) The size of paper in the upper drawer is not displayed correctly. Causes Poor contact in the lower paper switch connector terminals. Defective lower paper switch. Check procedures/corrective measures Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Check if CN15-10 on the engine PCB goes low when the lower paper switch is turned on with 5 V DC present at CN15-8 on the engine PCB. If none, replace the lower paper switch. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Check if CN14-A4 on the engine PCB goes low when the bypass paper switch is turned on with 5 V DC present at CN14-A2 on the engine PCB. If not, replace the bypass paper switch. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
Poor contact in the bypass paper switch connector terminals. Defective bypass paper switch.
Poor contact in the upper paper length switch* connector terminals (inch specs). Poor contact in the upper paper width switch* connector terminals (inch specs). Defective upper paper length switch* (inch specs). Defective upper paper width switch* (inch specs). Incorrectly set drawer paper size in copier management mode (metric specs).
Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
Check if CN8-A8 on the engine PCB goes low when the upper paper length switch is turned on. If not, replace the upper paper length switch. Check if the levels of CN9-19, CN9-20 and CN9-21 on the engine PCB change alternately when the width guide in the upper drawer is moved. If not, replace the upper paper width switch. Check the drawer paper size and reset.
3-6-85
2AD Problem (42) The size of paper in the lower drawer is not displayed correctly. Causes Poor contact in the lower paper length switch* connector terminals (inch specs). Poor contact in the lower paper width switch* connector terminals (inch specs). Defective lower paper length switch* (inch specs). Defective lower paper width switch* (inch specs). Incorrectly set drawer paper size in copier management mode (metric specs). Check procedures/corrective measures Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
Check if CN8-A10 on the main PCB goes low when the lower paper length switch is turned on. If not, replace the lower paper length switch. Check if the levels of CN9-23, CN9-24 and CN9-25 on the engine PCB change alternately when the width guide in the lower drawer is moved. If not, replace the lower paper width switch. Check the drawer paper size and reset.
3-6-86
2AD Problem (43) A paper jam in the paper feed, paper conveying or fixing section is indicated on the touch panel immediately after the main switch is turned on. Causes A piece of paper torn from copy paper is caught around paper feed switch 1/2/3, the feed switch or the eject switch. Defective paper feed switch 1. Check procedures/corrective measures Check and remove if any.
With 5 V DC present at CN13-5 on the engine PCB, check if CN13-4 on the engine PCB remains low when paper feed switch 1 is turned on and off. If it does, replace paper feed switch 1. With 5 V DC present at CN13-8 on the engine PCB, check if CN13-7 on the engine PCB remains low when paper feed switch 2 is turned on and off. If it does, replace paper feed switch 2. With 5 V DC present at CN13-11 on the engine PCB, check if CN13-10 on the engine PCB remains low when paper feed switch 3 is turned on and off. If it does, replace paper feed switch 3. With 5 V DC present at CN13-2 on the engine PCB, check if CN13-1 on the engine PCB remains low when the feed switch is turned on and off. If it does, replace the feed switch. With 5 V DC present at CN8-B1 on the engine PCB, check if CN8-B2 on the engine PCB remains low when the registration switch is turned on and off. If it does, replace the registration switch. With 5 V DC present at CN3-B10 on the engine PCB, check if CN3-B9 on the engine PCB remains low when the eject switch is turned on and off. If it does, replace the eject switch.
3-6-87
2AD Problem (44) The message requesting covers to be closed is displayed when the front, left and right covers are closed. (45) Others. Causes Poor contact in the connector terminals of safety switch 1, 2 or 3. Defective safety switch 1, 2 or 3. Check procedures/corrective measures Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Check for continuity across each switch. If there is no continuity when the switch is on, replace it.
3-6-88
2AD SRDF Problem (1) The original feed motor does not operate. Causes Defective original feed motor coil. The connector terminals of the original feed motor make poor contact. Defective DF driver PCB. (2) The original conveying motor does not operate. Defective original conveying motor coil. The connector terminals of the original conveying motor make poor contact. Defective DF driver PCB (3) The original feed solenoid does not operate. Defective original feed solenoid coil. The connector terminals of the original feed solenoid make poor contact. Defective DF driver PCB. Check procedures/corrective measures Check for continuity across the coil. If none, replace the original feed motor. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Check for continuity across the original feed motor coil and connector terminals. If good, replace the DF driver PCB. Check for continuity across the coil. If none, replace the original conveying motor. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
Check for continuity across the original conveying motor coil and connector terminals. If good, replace the DF driver PCB. Check for continuity across the coil. If none, replace the original feed solenoid. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
Check if the original feed solenoid operates when CN5-B13 or CN5-B12 on the DF driver PCB is low. If it does, replace the DF driver PCB.
3-6-89
2AD Problem (4) The switchback feedshift solenoid does not operate. Causes Defective switchback feedshift solenoid coil. The connector terminals of the switchback feedshift solenoid make poor contact. Defective DF driver PCB. Check procedures/corrective measures Check for continuity across the coil. If none, replace the switchback feedshift solenoid. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
Check if the switchback feedshift solenoid operates when CN5-B8 on the DF driver PCB is low. If it does, replace the DF driver PCB. Check for continuity across the coil. If none, replace the eject feedshift solenoid. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
Defective eject feedshift solenoid coil. The connector terminals of the eject feedshift solenoid make poor contact. Defective DF driver PCB.
Check if the eject feedshift solenoid operates when CN5-A7 on the DF driver PCB is low. If it does, replace the DF driver PCB. Check for continuity across the coil. If none, replace the switchback pressure solenoid. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
Defective switchback pressure solenoid coil. The connector terminals of the switchback pressure solenoid make poor contact. Defective DF driver PCB.
Check if the switchback pressure solenoid operates when CN5-A2 or CN5-A3 on the DF driver PCB is low. If it does, replace the DF driver PCB.
3-6-90
2AD Problem (7) The original feed clutch does not operate. Causes Defective original feed clutch coil. The connector terminals of the original feed clutch make poor contact. Defective DF driver PCB. (8) A message indicating cover open is displayed when the SRDF is closed correctly. (9) An original jams when the main switch is turned on. The connector terminals of DF safety switch 1 make poor contact. Defective DF safety switch 1. Check procedures/corrective measures Check for continuity across the coil. If none, replace the original feed clutch. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Check if the original feed clutch operates when CN5-A5 on the DF driver PCB is low. If it does, replace the DF driver PCB. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Check for continuity across the contacts of the switch. If none when the switch is on, replace DF safety switch 1.
A piece of paper torn from an original is caught around the original feed switch. Defective original feed switch.
With 5 V DC present at CN6-B4 on the DF driver PCB, check if CN6-B5 of the DF driver PCB remains low when the original feed switch is turned on and off. If it does, replace the original feed switch. Remove any found.
A piece of paper torn from an original is caught around the original switchback switch. Defective original switchback switch.
With 5 V DC present at CN6-A6 on the DF driver PCB, check if CN6-A5 on the DF driver PCB remains low when the original switchback switch is turned on and off. If it does, replace the original switchback switch.
3-6-91
2AD Problem (9) An original jams when the main switch is turned on. Causes A piece of paper torn from an original is caught around the DF timing switch. Defective DF timing switch. Check procedures/corrective measures Remove any found.
With 5 V DC present at CN6-A15 on the DF driver PCB, check if CN6-A14 on the DF driver PCB remains low when the DF timing switch is turned on and off. If it does, replace the DF timing switch.
3-6-92
2AD Feedshift and duplex sections Problem (1) The side registration motor does not rotate (C220). Causes Poor contact in the side registration motor connector terminals. Broken side registration motor gear. Defective side registration motor. (2) The feedshift solenoid does not operate. Broken feedshift solenoid coil. Poor contact in the feedshift solenoid connector terminals. Defective engine PCB. (3) The duplex forward solenoid does not operate. Broken duplex forward solenoid coil. Poor contact in the duplex forward solenoid connector terminals. Defective engine PCB. Check procedures/corrective measures Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Check visually and replace the side registration motor if necessary. Check for continuity across the coil. If none, replace the side registration motor. Check for continuity across the coil. If none, replace the feedshift solenoid. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Run maintenance item U033 and check if CN3-A8 on the engine PCB goes low. If not, replace the engine PCB. Check for continuity across the coil. If none, replace the duplex forward solenoid. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Run maintenance item U033 and check if CN10-8 on the engine PCB goes low. If not, replace the engine PCB.
3-6-93
2AD Problem (4) The switchback feedshift solenoid does not operate. Causes Broken switchback feedshift solenoid coil. Poor contact in the switchback feedshift solenoid connector terminals. Defective engine PCB. (5) The duplex paper tapping solenoid does not operate. Broken duplex paper tapping solenoid coil. Poor contact in the duplex paper tapping solenoid connector terminals. Defective engine PCB. (6) The message requesting covers to be closed is displayed when the left cover is closed. (7) Others. Poor contact in safety switch 2 connector terminals. Defective safety switch 2. Check procedures/corrective measures Check for continuity across the coil. If none, replace the switchback feedshift solenoid. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
Run maintenance item U033 and check if CN10-10 on the engine PCB goes low. If not, replace the engine PCB. Check for continuity across the coil. If none, replace the duplex paper tapping solenoid. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Run maintenance item U033 and check if CN10-14 on the engine PCB goes low. If not, replace the engine PCB. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Check for continuity across the contacts. If there is no continuity when safety switch 2 is on, replace it.
3-6-94
2AD Large paper deck Problem (1) The large paper deck does not operate when the print key is pressed. (2) The deck paper conveying motor does not operate (C920). Causes Incorrect connection with the engine PCB. Check procedures/corrective measures Check the connector.
Poor contact in the deck paper conveying motor connector terminals. The deck paper conveying motor drive system overloaded. Defective deck main PCB.
Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
Check if the motor drive clock signal is present at CN12-3 on the deck main PCB when maintenance item U247 is run. If not, replace the deck main PCB. Check if the deck paper conveying motor rotates while the motor drive clock signal is present at CN12-3 on the deck main PCB when maintenance item U247 is run. If not, replace the deck paper conveying motor. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Check for continuity across the coil. If none, replace paper deck motor 1. Check if CN7-1 on the deck main PCB goes low when paper deck motor 1 is turned on (placing paper on the right cassette lift and closing the large paper deck will turn paper deck motor 1 on until deck level switch 1 turns on) while the deck open/closed safety switch is on and 24 V DC is present at CN14 on the deck main PCB. If not, replace the deck main PCB.
Poor contact in the paper deck motor 1 connector terminals. Broken paper deck motor 1 coil. Defective deck main PCB.
3-6-95
2AD Problem (4) Paper deck motor 2 does not operate (C922). Causes Poor contact in the paper deck motor 2 connector terminals. Broken paper deck motor 2 coil. Defective deck main PCB. Check procedures/corrective measures Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Check for continuity across the coil. If none, replace paper deck motor 2. Check if CN7-4 on the deck main PCB goes low when paper deck motor 2 is turned on (placing paper on the left cassette lift and closing the large paper deck will turn paper deck motor 2 on until deck level switch 2 turns on) while the deck open/closed safety switch is on and 24 V DC is present at CN14 on the deck main PCB. If not, replace the deck main PCB. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Check for continuity across the coil. If none, replace paper feed clutch 1. Check if CN4-4 on the deck main PCB goes low when maintenance item U247 is run. If not, replace the deck main PCB. Check for continuity across CN4-4 on the deck main PCB and CN1-4 on the interface PCB. If none, check the wiring. Run maintenance item U247. If paper feed clutch 1 does not operate while CN4-4 on the deck main PCB is low, check for continuity across CN5-5 & CN1-1 and CN5-6 & CN1-4 on the interface PCB. If none, replace the interface PCB. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Check for continuity across the coil. If none, replace paper feed clutch 2.
Poor contact in the paper feed clutch 1 connector terminals. Broken paper feed clutch 1 coil. Defective deck main PCB. Wiring problem.
Poor contact in the paper feed clutch 2 connector terminals. Broken paper feed clutch 2 coil.
3-6-96
2AD Problem (6) Paper feed clutch 2 does not operate. Causes Defective deck main PCB. Wiring problem. Check procedures/corrective measures Check if CN4-5 on the deck main PCB goes low when maintenance item U247 is run. If not, replace the deck main PCB. Check for continuity across CN4-5 on the deck main PCB and CN1-5 on the interface PCB. If none, check the wiring. Run maintenance item U247. If paper feed clutch 2 does not operate while CN4-5 on the deck main PCB is low, check for continuity across CN5-3 & CN1-1 and CN54 & CN1-5 on the interface PCB. If none, replace the interface PCB. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Check for continuity across the coil. If none, replace the paper conveying clutch. Check if CN4-6 on the deck main PCB goes low when maintenance item U247 is run. If not, replace the deck main PCB. Check for continuity across CN4-6 on the deck main PCB and CN1-6 on the interface PCB. If none, check the wiring. Run maintenance item U247. If the paper conveying clutch does not operate while CN4-6 on the deck main PCB is low, check for continuity across CN5-1 & CN1-1 and across CN5-2 & CN1-6 on the interface PCB. If none, replace the interface PCB.
Poor contact in the paper conveying clutch connector terminals. Broken paper conveying clutch coil. Defective deck main PCB. Wiring problem.
3-6-97
2AD
Replace if necessary (see page 3-3-3). Replace if necessary (see page 3-3-3). See pages 3-6-78 80.
See page 3-6-80. Check the width guide visually and correct or replace if necessary. Check the width guide visually and correct or replace if it is deformed. Repair or replace.
3-6-98
2AD Problem (4) The scanner does not travel. (5) Multiple sheets of paper are fed at one time. (6) Paper jams. Causes/check procedures Check if the scanner wire is loose. The scanner motor malfunctions. Check if the lower paper feed pulley is worn. Check if the paper is curled. Check if the paper is excessively curled. Deformed guides along the paper conveying path. Check if the contact between the upper and lower registration rollers is correct. Check if the separation charger wire in the transfer charger assembly is broken. Check if the paper conveying belt is off the paper conveying pulleys. Check if the fixing unit upper or lower left guide is deformed. Check if the press roller is extremely dirty or deformed. Check if the contact between the heat roller and its separation claws is correct. Check if the contact between the eject roller and pulley is correct. (7) Toner drops on the paper conveying path. Check if the developing unit is extremely dirty. Corrective measures Reinstall the scanner wire (see page 3-3-24). See page 3-6-75. Replace the lower paper feed pulley if it is worn (see page 3-3-3). Change the paper. Change the paper. Check visually and repair or replace any deformed guides. Remedy if necessary. Replace the pressure spring if it is deformed. Replace the separation charger wire if it is broken (see page 3-3-54). Remedy.
Repair or replace. Clean or replace the press roller. Repair if any springs are off the separation claws. Repair if a pressure spring is off the eject pulley. Clean the developing unit.
3-6-99
2AD Problem (8) Abnormal noise is heard. Causes/check procedures Check if the pulleys, rollers and gears operate smoothly. Check if the following electromagnetic clutches are installed correctly: upper/lower paper feed clutches, feed clutches 1/ 2/3/4/5 and bypass paper feed clutch. Corrective measures Grease the bearings and gears. Correct.
3-6-100
2AD SRDF Problem (1) No primary original feed. Causes/check procedures The surfaces of the DF forwarding pulleys, DF original feed pulley or DF separation pulley are dirty with paper powder. Check if the DF original feed pulley or the DF separation pulley is deformed. Check if the DF forwarding pulleys are deformed. Electrical problem with the following clutch or solenoid: Original feed solenoid Original feed clutch (2) No secondary original feed. (3) Originals jam. The DF registration pulley and the DF registration roller do not contact each other correctly. Originals outside the specifications are used. The surfaces of the DF forwarding pulleys, DF original feed pulley or DF separation pulley are dirty with paper powder. The DF original feed pulley and the DF separation pulley do not contact each other correctly. Corrective measures Check and clean them with isopropyl alcohol if they are dirty.
If so, replace (see pages 3-3-88 and 90). If so, replace (see page 3-388). See pages 3-6-89 and 91.
Remedy.
Use only originals conforming to the specifications. Check and clean them with isopropyl alcohol if they are dirty.
Remedy.
3-6-101
2AD Feedshift and duplex sections Problem (1) No refeed. Causes/check procedures Check if the surfaces of the following rollers and pulleys are dirty with paper powder: duplex forwarding pulley, refeed pulley, switchback roller and duplex upper/lower registration rollers. Check if the duplex forwarding pulley is deformed. Electrical problem with the paper tapping solenoid. (2) Paper is refed askew. (3) Paper jams. Side registration amount adjusted incorrectly. Check if the paper is excessively curled. Deformed guides along the paper conveying path. The feedshift solenoid malfunctions. Check if the contact between the feedshift lower roller and feedshift pulley is correct. (4) Abnormal noise is heard. Check if pulleys, rollers and gears operate smoothly. Corrective measures Clean with isopropyl alcohol.
Replace (see page 3-3-79). See page 3-6-94. Run maintenance item U052 and adjust the side registration amount (see page 3-3-87). Change the paper. Check visually and repair or replace any deformed guides. See page 3-6-93. Repair if the mount has come off the feedshift pulley. Grease the bushings and gears.
3-6-102
2AD Large paper deck Problem (1) No primary paper feed. Causes/check procedures Check if the upper or lower deck separation roller is dirty with paper powder. Check if deck paper feed roller 1, 2 or the deck paper conveying roller is dirty with paper powder. Check if the upper or lower deck separation roller is worn or deformed. Check if deck paper feed roller 1, 2 or the deck paper conveying roller is worn or deformed. Check if paper feed clutch 1, 2 or the paper conveying clutch malfunctions. (2) Paper is fed askew. Check if the upper or lower deck separation roller is worn or deformed. Check if deck paper feed roller 1, 2 or the deck paper conveying roller is worn or deformed. Check if the paper side guides are deformed. (3) Multiple sheets of paper are fed at one time. Check if the paper is excessively curled. Paper is not loaded correctly. Check if the upper or lower deck separation roller is worn or deformed. Check if the paper is excessively curled. Check if the upper and lower deck separation rollers contact each other when the deck is installed correctly. Corrective measures Clean with isopropyl alcohol.
Remedy or replace.
Remedy or replace. Change the paper. Correct. Replace (see page 3-3-101).
3-6-103
2AD Problem (4) Paper jams. (5) Abnormal noise is heard. Causes/check procedures Check if the paper side guides are deformed. Check if rollers and gears operate smoothly. Check for any abnormality with motors and clutches. Check for any drive belt out of place. Corrective measures Remedy or replace. Grease the bushings and gears. Replace. Remedy if necessary.
3-6-104
2AD
1-1-33
2AD Interface PCB .............................................................................................. SRDF connection diagram .......................................................................... General connection diagram ....................................................................... SRDF wiring diagram .................................................................................. Large paper deck wiring diagram ................................................................ Optical section wiring diagram .................................................................... General wiring diagram ............................................................................... 3-7-45 3-7-46 3-7-47 3-7-48 3-7-49 3-7-50 3-7-51
1-1-34
E A E
E A E
2AD
Timing chart No. 1 From the main switch turned on to machine stabilization
A B C D
Primary stabilization fixing temperature 175C/347F
F
Secondary stabilization fixing temperature 190C/374F
Copying possible*
MSW 3 PRY H1 H2 4
Aging end
MSW: On
5 DM
PCM CL DB REM CFM1 (Half speed) CFM1 (Full speed) PCFM IFFM PM
200 ms 270 ms
600 ms 50 ms
8
* Copying is possible at the earlier timing of 120 s after secondary stabilization or 176 s after PRY turning on.
3-7-1
E A E A A E Point Source Ai5050 (MCA) E A A E
E E A
A E A 2AD 8 7 6 5 4 3 2 1
E A
3-7-2
A
Scanner initialization (SHPSW: ON) Fwd. rotation
B
Rev. rotation
SM
E
SHPSW CN4-2
A C
43 P
154 P
D
Scanner initialization (SHPSW: OFF) Fwd. rotation CN2-1,2, 3,4,5,6 Rev. rotation Off
E
SM SHPSW CN4-2
F G H
SM CN2-1,2, 3,4,5,6
76 P
43 P
154 P
Original scanning operation (A3/11" x 17" original, magnification ratio 100%, manual copy density control)
SHPSW
CN4-2
J 8 7 6 5 4 3 2 1
A E
E A E
E A E
2AD
Timing chart No. 3 Original feed operation 1: single-side original mode, multiple originals
A B C D E F G H I J
Repeats
Original ejection
2OSSW
CN6-B2
200 ms
OFSOL A
CN5-B12
200 ms
3
OFSOL R OFCL CN5-B13 CN5-A5
4
20 ms 30 ms + 288 P*2 20 ms 30 ms + 288 P*2
4
CN5-B3, B4, B5, B6 CN6-B5
OFM OFSW
556 P*2
556 P*2
5
OSBSW CN6-A5
6OCM
30 ms + 2337 P*3
CN5-A10, A11, A12, A13 CN6-A14 *1 During enlargement copying: (magnification 10 530) ms *2 Burst of OFM pulses *3 Burst of OCM pulses
DFTSW
3-7-3
E A E A A E Point Source Ai5050 (MCA) E A A E
E A E
E A E
2AD
Timing chart No. 4 Original feed operation 2: double-sided original mode, multiple originals (1 /2 )
A B C D E F G H I J
1
Repeats Primary original feed OSSW CN6-B2 Scanning the first face Switchback operation
2
200 ms
2
CN5-B12
OFSOL A
OFSOL R 3 OFCL
OFM 4 OFSW
SBFSSOL
CN5-B8
5
564 P*2
5
CN5-A2 CN5-A3 CN6-A5
30 ms
OCM EFSSOL
7
DFTSW CN6-A14
3-7-4
E A E A E A Point Source Ai5050 (MCA) E A A E
E A E
E A E
2AD
Timing chart No. 5 Original feed operation 2: double-sided original mode, multiple originals (2 /2 )
A B C D E F G H I J
1
Repeats Switchback operation Primary feed of next original Scanning the image Original ejection
OSSW
CN6-B2
2
OFSOL A CN5-B12
200 ms
3OFSOL R
OFCL
CN5-B13 CN5-A5
Scanning speed 115 P*1 100 ms 327 P*1 100 ms 288 P*2 30 ms 100 ms 20 ms 30 ms
OFM OFSW
4
556 P*1
SBFSSOL
CN5-B8
SBPSOL A SBPSOL R
6OSBSW
6
30 ms
OCM EFSSOL
7
DFTSW CN6-A14
3-7-5
E A E A A E Point Source Ai5050 (MCA) E A A E
E A E
E A E
2AD
Timing chart No. 6 Copying an A3/11" 17" original onto an A5R/51/2" 81/2" copy paper from the bypass table, magnification ratio 25%, manual copy density control
A B C D E F G H I J
Image ready
Print key CL CFM1 CN2-A2 CN3-B4 CN3-B6 CN13-1 CN8-B2 CN12-A2 CN8-B11 CN3-B9 CN5-B10 CN5-B13 CN5-B5 CN5-B7 CN11-3 CN12-B4 CN5-A8 CN14-A8
250 ms 520 ms 100 ms 300 ms 90 ms 50 ms 520 ms 700 ms 210 ms 270 ms 300 ms 115 ms 65 ms 74 ms 74 ms 100 ms 50 ms 360 ms 520 ms 520 ms
600 ms
4
RCL ESW DB REM
80 ms
600 ms
7
BYPPFCL CN14-A7
7
200 ms
3-7-6
E A E A E A Point Source Ai5050 (MCA) E A A E
E A E
E A E
2AD
Timing chart No. 7 Copying an A4/11" 81 /2 " original onto an A4/11" 81 /2 " copy paper from the copier upper drawer, magnification ratio 100%, auto copy density control
A B C D E F G H I J
1
Image ready
1
Print key CL CN2-A2 CN3-B4 CN3-B6 CN8-B9 CN13-1 CN8-B2 CN12-A2 CN8-B11 CN3-B9 CN5-B10 CN5-B13 CN5-B5 CN5-B7 CN11-3 CN12-B4 CN5-A8 CN15-13 CN12-A8 CN13-7 CN12-A4 CN13-4
28 ms 35 ms 250 ms 520 ms 100 ms 50 ms 163 ms 58 ms 50 ms 520 ms 700 ms 210 ms 270 ms 300 ms 600 ms 74 ms 74 ms 80 ms 100 ms 174 ms 50 ms 360 ms 520 ms 520 ms 35 ms 600 ms 29030000 ms Toner replenishment 600 ms
4
ESW DB REM MC REM
7
PFSW2 FCL1 PFSW1
3-7-7
E A E A A E Point Source Ai5050 (MCA) E A A E
E A E
E A E
2AD
Timing chart No. 8 Continuous copying of an A5R/51/2" 81/2" original onto two sheets of A3/11" 17" copy paper from the copier lower drawer, magnification ratio 400%, manual copy density control
A B C D E F G H I J
1
Print key CL CFM1 CN2-A2 CN3-B4 CN3-B6 CN8-B9 CN13-1 CN8-B2 CN12-A2 CN8-B11 CN3-B9
50 ms 520 ms 520 ms 174 ms
Image ready
35 ms
174 ms
35 ms
3
74 ms 74 ms 100 ms 80 ms 74 ms 74 ms 100 ms 80 ms
4
DB REM CN5-B10 MC REM CN5-B13 SC REM CN5-B5
50 ms 520 ms 700 ms 210 ms 270 ms 210 ms 270 ms 300 ms 600 ms
365 ms
100 ms 50 ms
365 ms 35 ms 50 ms
128 ms
128 ms
35 ms
7
FCL2 PFSW2 FCL1 CN12-A8 CN13-7 CN12-A4 CN13-4
128 ms 35 ms 209 ms 35 ms
128 ms
7
35 ms
209 ms
35 ms
PFSW1
3-7-8
E A E A E A Point Source Ai5050 (MCA) E A A E
E E A
A E A 8 7 6 5 4 3 2 1 A
Print key FSSOL1 1160 ms 200 ms 1160 ms 200 ms FSSOL2 SBFSSOL1 SBFSSOL2 CN10-12 CN10-10 CN3-A9 CN3-A8
E A
B
FSSW DUPFWDSOL 30 ms DUPPTSOL SRM 60 ms 12 P SRHPSW DUPRSW CN9-7 CN9-8 CN9-11 CN11-3 DUPPCSW DUPESW PFM CN10-1,2,3, 4,5 CN9-12 CN10-14 500 ms CN10-8 CN3-A4
C D
DM CN12-B4 250 ms 520 ms 100 ms 162 ms 58 ms 50 ms CN5-A8 CN15-13 CN12-A8 CN13-7 PCM PFCL-U FCL2 PFSW2
C D
E
FCL1 CN12-A4 128 ms CN13-4 CN8-B9 CN13-1 CN8-B2 174 ms PFSW1 FCL4 FSW RSW
232 ms
35 ms 30 ms
35 ms
F
FCL5 RCL ESW CN12-A2 CN8-B11 CN3-B9 74 ms Image ready 100 ms 80 ms 74 ms 100 ms 80 ms
G
CL CN2-A2 50 ms CFM1 CN3-B4 520 ms 360 ms 600 ms
CFM2
CN3-B6
290-30000 ms
Timing chart No. 9 Duplex copying of an A3/11" 17" book original onto one duplex A4/11" 81 /2 " copy from the copier upper drawer, magnification ratio 100%, auto copy density control
DB REM
300 ms
SC REM
CN5-B5 700 ms
TC REM
3-7-9
2AD A E E A
E A E
E A E
2AD
Timing chart No. 10 Continuous, duplex copying of two single-sided A4/11" 81/2" originals onto two duplex A4/11" 81 /2 " copies from the copier upper drawer, magnification ratio 100%, auto copy density control
A
Print key FSSOL1 FSSOL2 SBFSSOL1 SBFSSOL2 FSSW
CN3-A8 CN3-A9 CN10-10 CN10-12 CN3-A4 CN10-8 CN10-14 CN10-1,2,3, 4,5 CN9-12 CN9-7 CN9-8 CN9-11 CN11-3 CN12-B4 CN5-A8 CN15-13 CN12-A8 CN13-7 CN12-A4 CN13-4 CN8-B9 CN13-1 CN8-B2 CN12-A2 CN8-B11 CN3-B9 CN2-A2 CN3-B4 CN3-B6 CN5-B10 CN5-B13 CN5-B5 CN5-B7 50 ms 74 ms Image ready 50 ms 520 ms 174 ms 128 ms 100 ms 50 ms 250 ms 520 ms 162 ms 58 ms
1160 ms
200 ms 1160 ms
200 ms
30 ms 60 ms 12 P
30 ms 60 ms 12 P
2
12 P
34 ms 128 ms 58 ms
232 ms
232 ms 35 ms 35 ms
35 ms 174 ms
35 ms
30 ms
30 ms
100 ms 1200 ms 80 ms
100 ms 80 ms 74 ms
100 ms 1200 ms 80 ms
100 ms 80 ms
6
600 ms 360 ms 290-30000 ms
7
300 ms
TC REM
3-7-10
E A E A E A Point Source Ai5050 (MCA) E A A E
E A E
E A E
2AD
Timing chart No. 11 Primary paper feed from large paper deck right cassette
A B C D E F G H I J
100 ms 64 P
100 ms 64 P
4
PFSW4 (from the copier) PPSENS1 CN4-9
5
PPSENS2 CN1-6
PPSENS3 CN1-11
6
PFCL1 CN4-4 CCL CN4-6
7
PFCL2 CN4-5
3-7-11
E A E A A E Point Source Ai5050 (MCA) E A A E
E A E
E A E
2AD
Timing chart No. 12 Primary paper feed from large paper deck left cassette
A B C D E F G H I J
3
Paper feed signal from the copier
100 ms 64 P
100 ms 64 P
PPSENS1 CN4-9
PPSENS2 CN1-6
PPSENS3 CN1-11
6
PFCL1 CN4-4
CCL CN4-6
43 P
43 P
PFCL2 CN4-5
3-7-12
E A E A E A Point Source Ai5050 (MCA) E A A E
2AD
FUSE1 TAB1
L1
AB6
D201
R206 R202 + C203 D202 AB7 AB4 D203 AB8 AB5 C202 L201 + C204 C205 C207 IC3 PC1 R203 C206 R207 R205
ZD201 R208
2
FUSE2 TAB2 "N"
R1
R2
R3
C1
C2
C3 C5
18 17, 16,
AB3
24 V 24 V 24 V
R502 ZD501
TRNS
R603
Q602
C001
C002
R319
R318
R147
R149
C006
R137 C111
R301
SLEEP SIGNAL
C308 R312 Q301 L302 5.1 V FUSE4 R314 R310 5.1 V FUSE6 5.1 V R311 D302 + C305 R306 R309 + VR301 C306 C307 R320 D301 Q302
R141
RF1
R127
R143 R142 R150 R151 FB2 Q106 FB1 R117 D113 R129
R128
D105 +
PC3
R118
R109
ZD105
R408
D601
R317
R304
R135 C116 Q111 + R126 C121 R134 R125 R124 R132 L401 PC2 R104 L102 D101 R119 R101
1 2 3 4 5 6 7 8
IC4
1 2 3 4
C302
5
H1 COM CN101
R315
R308
Q303
TR2 R152 Q110 R133 + R160 Q113 R161 R162 C127 CR1 PT1 C123
5
L402 5.1 V
16
15
14
13
12
11
10
+ C401 8
C406
D401
R103
C126
IC1 D103
R106
C403
C404
Q109 C120 R120 C119 IC2 + ZD101 ZD102 R102 C110 C109 C114 C115 C108
1 2 3 4
R405 C402
C118
C117
R122
GND C106 R107 9 D502 CN111 R903 IC7 R701 Q701 + C503 C502 R702 Q502 R901 CN123 R902
2 3
R121
R123
IC6 R501
2 3
7
+ C504 C501
Q901
C901
C701
GND (12 V)
3-7-13
2AD B
R76 D13 R78 C E S G R60 S R63 R61 TR6 R62 C27 S G P G R93 S R96 R94 TR8 R95 C41 S G P G R102 R100 TR12 R101 C42 P G S G CN1-10 SSW3 CN1-9 SSW2 B CN1-81 SSW1 PWSW-U DIG2 PWSW-U DIG1 PWSW-U DIG0 PLSW-U CN1-11 SSW1 PWSW-L DIG2 PWSW-L DIG1 PWSW-L DIG0 PLSW-L BYPPWSW DIG2 BYPPWSW DIG1 BYPPWSW DIG0 BYPPLSW PSW-L PSW-U BYPPSW LICSW-L CN9-21 CN9-20 CN9-19 CN8-A8 CN9-25 CN9-24 CN9-23 CN8-A10 CN14-B2 CN14-B3 CN14-B4 CN14-B8 CN15-10 CN15-9 CN14-A4 CN15-4 R173 R174 R175 R164
S
D
S
E
2 RA7 3 4 1 7 6 5 8 CN1-47 CN1-48 CN1-49 CN1-50 PWSW-U DIG2 PWSW-U DIG1 PWSW-U DIG0 PLSW-U
F
S
G
CN9-8 CN9-11 CN9-7 CN9-16 CN12-B3 CN5-A7 CN5-B3 CN5-B11 R179 R178 R180 R176
S
H
CN1-31 CN1-30 CN1-29 CN1-28 DUPPCSW DUPESW DUPRSW STKSW NF3
S
3 2 4 1
RA8
6 7 5 8
1
SSW1 CN4-1
1
NF1 14 IC1 C10 S G NF22 14 IC18 7 C44 S G R119 NF16 7 C48 R7
S S
2 4 3 1
RA6
7 5 6 8
1 2 3 4
RA2
8 7 6 5
14 IC3 7
C14
C12 C8
SSW2 SOURCE
CN4-2
S G NF10
R5
S
R120 NF24
S
SSW2
CN4-7
4 3 2 1
RA4
5 6 7 8
R14 R13 R20 R22 R44 R161 R198 R154 R148 R196 R32 R66 R151 R200 R150
R15 CN1-3 R12 CN1-4 R16 CN1-5 R21 CN1-6 R46 CN1-7 R162 CN1-22 R199 CN1-24 R155 CN1-32 R147 CN1-33 R195 CN1-34 R23 CN1-63 R57 CN1-64 R149 CN1-25 C58 S G CN1-74 R201 K . COUNTER SET SIG FINISHER SET SIG IC21 4 +
14 IC5
14 IC20 7
C50 C46
SSW3 SOURCE
CN4-8
SSW3
CN4-3
4 3 2 1
RA3
5 6 7 8
ESW FSSW
S G
R122 NF14
PRY SOURCE
CN4-4
IC13 +
8 4
IC7 +
8 4
8 IC11 4 S G
PFM LOCK 2 3 4 1 RA1 7 6 5 8 CN1-60 CN1-61 CN1-62 CN1-59 BYPEDSW SRHPSW SET SIG LICSW-U RSW FSW
PRY REM
CN4-9 P G
S G
S G
3
S 1,8
R111 S G
S S
R159
R160
R156 C59
4 3 2 1
RA5
5 6 7 8
CN20-3 CN21-6
9,16 IC14 +
8 4
IC12
+ 8
C34 C29
COM 4,5
CN2-A12
11 S G
12,13 P G
S G
S G
IC1 B 8 9
S
TxD
PFSW4
CN17-7
C E S G
NF5 CN2-A11 CN2-B2 NF8 CN2-B5 CN3-A3 CN3-A6 NF33 CN3-B11 CN5-A2 CN5-A10 NF43 CN5-B9 CN8-A7 CN8-A9 NF65 CN8-B3 CN9-1 CN9-3 CN9-4 CN9-9 CN9-10 CN9-17 CN9-18 CN9-22 NF53 NF39 CN9-26 CN11-5 CN12-A5 CN12-B6
NF73 CN13-3 CN13-6 CN13-9 CN13-12 NF29 CN13-15 CN14-A3 CN14-A9 CN14-B7 CN14-B6 NF20 CN14-B1 CN15-5 CN15-6 CN15-11 NF77 CN15-12 CN16-7 CN16-9 NF72 CN16-11 CN17-1 CN17-3 NF46 CN17-5 CN18-4 CN18-10 NF9 NF18 NF52 CN18-12 CN19-B9 CN20-4 CN21-1 CN21-3 C50 C51 R165 CN2-B1 CN5-A5 CN8-A1 N.C N.C N.C N.C N.C CN16-4 N.C P G CN17-13 N.C CN17-14 N.C CN17-15 N.C CN17-16 N.C CN18-5 N.C 12 V D5 R10 IC23 D G I C63 C52 R166 C7 CN7-2 CN6-6 G (24 V) + S G CN6-5 CN7-1 R24 V C15 C57 C56 R153 S G
R
+ IC7
(A)
4
+
6 S G 11 S G 7
3 IC19
7 IC1 10 S G
(A)
CN3-B7 CN5-A4 CN5-A9 CN8-A11 CN8-B1 CN9-5 CN9-6 CN9-13 CN9-14 CN9-15 CN11-4 CN12-A6 CN12-B5 CN13-2 CN13-5
2 ZD1
+ 2
NF75
R197
R168
R167 C64
RxD
CN16-12
4 IC1
R84 + 1 CN1-21
CN1-90
RxD
S R85
2 IC13 R86
24 V
S G C40 10 11 IC19
S
C4
NF54 NF40
G (24 V)
E 5.1 V
9 IC19
NF74
S
D2
G (5 V)
6
FRxD CN21-4
R144 R145
R139 5 C54 4
6
LSU5 V ON/OFF
S G
3 IC13
R9 CN1-2
S G
B DT12
CN1-102 RESET
S
7
NF69 CN17-8 NF67 CN17-9 NF68 CN17-10 NF79 CN17-11 6 10
S G
CN5-B14 N.C CN17-2 CN19-A1 CN19-A2 CN19-A3 CN19-A4 CN19-A5 CN19-A6 CN8-A6 CN16-3
R89
IC12 + 1
13
CN12-B1 N.C
IC12 + 7
6 R54
CN19-A7 CN19-A8
8
NF66 CN17-12
S R189
3-7-14
2AD B C D
IC6 9 8 R43 CN19-B8 R45 CN19-B7 R50 CN19-B6 R51 CN19-B5 D14 CN1-67 IC5 9 8 R52 CN19-B4 FSSOL1 CN1-68 IC5 5 6 R53 CN19-B3 R56 CN19-B2 R65 CN19-B1 NF13 CN19-B10 NF62 CN6-7 NF63 CN6-8 H2 REM ESCL CN1-77 14 H1 REM DM REM IC4 11 IC4 15 CN3-A11 D25 DT10 IC18 7 NF6 CN2-B9 TNS CONT DM REM CN1-113 DM CLK CN1-112
S R27
R R
F
IC4 TC CN1-101
S R38
G
3 2 R41 R40
FCL5 FCL1
FCL5 FCL1
CN1-65
CN3-B2
TC
1
FCL2 FCL3
IC5 13
12
TC
CN1-23 TR3
1
R42 R69 MAIN 5 V CN1-12 R70 S G FSSOL1 R82 C39 S G TR10 FSSOL2 MSW OFF CN1-82 DT4 B E S G
S
R
IC6 11
10
S G
R39
CN1-136
IC5 11
10
P G
5 IC13 + 7 C32 6 R83 S R92 R97 _RES CN4-10 TR11 R98 P G MSW OFF
TR4
CN3-A8 D15
R
P G
SRM B_
FSSOL2
CN1-137 CN15-13 CN15-14 CN14-A7 CN20-2 PFCL-U PFCL-L BYPPFCL CN1-140 KC COUNT H1 REM CN1-109 CN1-138
IC6 13
12
R91
IC5
S R25
3 IC5 1
_INH
S
C43 S G R114 5 15 10 20 6 16
INH1 2 INH2 19 N.C. 1 N.C. 11 Vcc2 12 Vcc1 9
C3 + P G 3
IC6
10
CN3-B4 CN3-B6
R126 TR13 P G
CN14-A8
BYPSOL
H2 REM
CN1-108
IC6
ESCL
D21
S G 4 17 14 7 IC15
I1 I2 I3 I4
O1 18 O2 13 O3 8 O4
D23
CN1-128 CN1-127
TNS CONT
IC14 + 5 6 R90
1 IC6 1
S 2
1 1B E 3 2B
1C 6 R184 2C 4 R185
TR17
P G CN10-8 D26
R
P G TR18
+ S G 7 1 8 C5 P G
VCC VCC 1 2 9 INH MONI
CN10-14
4
SC CONT CN1-14
S G 3 IC21 + 1 IC20 NF44 CN5-B4 SC CONT SC REM CN1-83 1 (A) IC20 TC REM 5 IC21 + 7 6 NF36 CN5-B6 TC CONT DB REM CN1-85 5 CN1-84 3 (A) IC20 (A) IC20 NF34 CN5-B8 DB CONT MC REM CN1-86 9 (A) IC20 PCM CLK GRID CONT CN1-17 R132 S G
S
CN1-116 CN1-117
CN8-B5 CN8-B4
NF38 CN5-B5 NF35 CN5-B7 NF32 CN5-B10 DB REM DT9 NF27 CN5-B13 MC REM NF57 CN5-A6 NF58 CN5-A8 PCM REM PCM CLK CN1-124 CN1-129 TC REM SC REM SBFSSOL1 SBFSSOL2 CN1-126 CN1-125
S 2
1 1B E 3 2B
CN10-10 D27
R
5 P G
S
IC22
CN10-12
E C DT6 DT1
R142
P G
DB CONT
CN1-16 R135 S G
10
IC21 + 8
S 2
1 1B E 3 2B
1C 6
R182
TR15
CN10-18 D24
R
S 2
2C 4 R183
P G TR16 P G
CN1-110
S
11 R121 13
10
1 1B E 3 2B
1C 6 R19 2C 4 R17
CN2-A4
IFFM REM
P G TR1
12
IC21 + 14 13
CN2-A2
CL REM
12
R18 P G S G C23
S
R
PFM CLK CN12-A9 CN12-B10 CN12-B9 CN14-A5 CN14-A6 CN15-15 CN15-16 PFM REM F2
CN1-88
5 2B 2 1B
CN1-75
6
C2 + P G
O1 18 O2 13 O3 8 O4
R
CN5-A14 CN5-B1 CN8-A2 CN8-A4 CN8-B10 CN8-B8 CN8-B6 CN10-5 CN10-6 CN10-7 CN4-5
CN10-9 CN10-11 CN10-13 CN10-15 CN10-17 CN11-8 CN11-9 CN12-A1 CN12-A3 CN12-A7
_PRE
Q 9
S G 4 17 14 7 5 15 10 20 6 16
INH1 INH2 N.C. N.C. Vcc2 Vcc1 I1 I2 I3 I4
S G
S
_CLR
CLK IC2 _Q
S
D6
D9
D7
13 12 5 IC3
_PRE
_CLR
2 1B 1E 1 S G
1C 6
12
CLK _Q
S
4 2 1
IC3
2 19 1 11 12 9
CN1-87
5 2B
2C 3
4 2E
DT7 2
11
13
IC18
D8
1 13
CN16-1 CN20-1
TFM/TRM CLK
CN1-73
C26 S G R73
IC11 7 6
IC11 2
F3
IC11 3 5 _RES
3-7-15
2AD D
IC13 2 4
E
IC13 3 4 IC18 3 R115
F
R116 R118 S L26 CN6-5 C44 S G R117 S G
RXD MMI
R198
6 IC18
S G
PRTACK IC34 CN1-69 ENG 5 V S _G2B 5 _G2A 4 G1 6 S G C 3 B 2 A 1 R244 S G R243 3 _B RAM R194 IC17 _Y0 _Y1 _Y2 _Y3 _Y4 _Y5 _Y6 _Y7 15 14 13 12 11 10 9 7 IC24 1 2 6 IC13 5 S R107 _Y7 _Y6 _Y5 _Y4 _Y3 _Y2 _Y1 _Y0 7 9 R233 10 11 R232 12 13 14 R231 15 S R193 S SCC1 L100 _MAIL S _WR M _WR S _RD M _RD S RAM M MAIL M 4 6 5 IC24 _WAIT M R229 A0 A1 A2 A3 A4 A5 A6 A7 AD0 AD1 AD2 AD3 AD4 AD5 AD6 AD7 R195 _ROM M S R228 R227 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 S G _MAIL M C85 C86 S G R188 _CSA Vcc _WEA _CSB _NRA _WEB _OEA _NRB A0A _OEB A0B A1A A1B A2A A2B A3A A3B A4A A4B A5A A5B A6A A6B A7A A7B D0A D7B D1A D6B D2A D5B D3A D4B D4A D3B D5A D2B D6A D1B D7A D0B GND IC29 [AD0S-AD7S] 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 R189 S R190 _WAIT S A0S A1S A2S A3S A4S A5S A6S A7S AD7S AD6S AD5S AD4S AD3S AD2S AD1S AD0S R191
RA11 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 AD0 AD1 AD2 AD3 AD4 AD5 AD6 AD7 RA17 A22 A21 A20 R242
G (5 V) G (5 V) G (5 V)
9 IC18
11 IC18
10
3
ENGERR MMI CN6-8
MACK ENG _P2 _MRDY MACK PRT L29 12 13 IC6 L27 2 1 IC6 R419 R420 S G L28 S R9 _WAIT M
ENGACK MMI
CN6-6
BYTE CNVss _RESET Xin Xout _RD Vss Vcc _HLDA ALE _BHE _WR P117 P116 P115 P114 P113 P112
MMI TH
CN6-11
P70 INT3 P94 A22 A21 A20 P90 P67 P66 P65 INT2 INT1 INT0 TA4in P60 P57 P56 P55 TA2out P53 TA1out P51 TA0out P47 P46 P45 P44 P43 I _RDY
_HOLD 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 R200
A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 DCS D0 D1 D2 D3 D4 D5 D6 D7 P110 P111
RA12
RA13
RA14
RA15
1 A 2 B 3 C
RA16
S 6 G1 4 _G2A 5 _G2B
[A0S-A7S]
MMI ERROR
CN6-7
C81 _RESET R192 S G R201 _RAM M _WR M L89 L96 L90 _PRTRST _RES M1 _RES M2 _RES SCC1 _RES ENG _RES SCAN _RES MMI _RD M R187 X4 C84 _RES MMI C91 S G R163 S R164 E _RD M _WR M S G
_M2OE M2SEL _M1OE M1SEL S R281 S IC43 CN1-12 CN1-82 MSW 5 V MSW OFF A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 S S R112 L62 S _RD M IC16 _B RAM 22 20 27 10 9 8 7 6 5 4 3 25 24 21 23 2 26 1 _WR M S A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 R90 R89 R88 R87 R86 R85 R84 R83 R57 R58 R60 R59 R82 R56 R55 R81 R80 R54 R53 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 12 11 10 9 8 7 6 5 27 26 23 25 4 28 29 3 2 30 31 IC11 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 D0 D1 D2 D3 D4 D5 D6 D7 _CE _OE 13 14 15 17 18 19 20 21 22 24 AD0 AD1 AD2 AD3 AD4 AD5 AD6 AD7 S R91 R92 R93 R66 R65 R64 R63 R62 R61 _ROM M _RD M _WR M _RD M _SCC1 INT SCC1 RSCAN TSCAN R268 22 20 27 10 9 8 7 6 5 4 3 25 24 21 23 2 26 1 _OE _CE _WE A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 Vcc 28 C119 GND I/O0 I/O1 I/O2 I/O3 I/O4 I/O5 I/O6 I/O7 14 11 12 13 15 16 17 18 19 R280 S G AD0 AD1 AD2 AD3 AD4 AD5 AD6 AD7 C113 R269 S G S L118 A7 A6 A5 A4 A3 A2 A1 A0 AD7 AD6 AD5 AD4 AD3 AD2 AD1 AD0 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 A7 A6 A5 A4 A3 A2 A1 A0 Vcc D7 D6 D5 D4 D3 D2 D1 L123 C120 48 47 46 45 44 4342 4140 39 38 37 36 35 34 33 PA0 PA1 PA2 PA3 PA4 PA5 PA6 PA7 PB0 PB1 PB2 PB3 PB4 PB5 PB6 PB7 SLP R310 S G R309 S R273 SLEEP 3 4 IC35
SLEEP_
5
L50 SC TIM CN5-20
5
B C E TR1 S G S C148 R331 1 S G 3 X6 2 _RES SCC1 CN10-2 SLEEP SIG
B TR5
R108
R101
IC41
C114
6
L38 RXD SCAN CN5-28
R41
R100 1 R247 R246 R245 C110 S G 8 9 IC13 R95 S G 2 IC35 13 12 IC18 RSCAN
D0 _W _R _S BM INTR RD3 TD3 RD2 TD2 RD1 TD1 P16 P15 P14 P13
P00 P01 P02 P03 P04 P05 P06 P07 Vss Xout Xin P10 P11 _RESET CNVss P12
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17
5 IC5
_RES SCAN
C34
28 C41 R103 14 11 12 13 15 16 17 18 19
Vcc
C132
7
S C127
S R320
RMCP2
RMCP1
24 V OFF
CN1-20 SLP
12 13
IC24
_RESET
L41 C22
8
R29 S G
S G
R418
3-7-16
2AD H I J
1
L109 TLS TLDS PFM LOCK EHUMSENS ETTH TNS SIG CN1-4 CN1-3 CN1-32 CN1-19 CN1-18 R133 C55 CN1-1 CN1-2 C58 C59 C60 C61 L78 C108 IC32 C54 CN1-16 DACLK LD DI CN1-17 DB CONT GRID CONT PPST _LDON _LDEN R128 5 4 S G6 A22S A21S A20S R221 S G RA3 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 R222 A0S A1S A2S A3S A4S A5S A6S A7S A8S A9S A10S A11S A12S A13S A14S A15S A16S A17S A18S A19S AD0S AD1S AD2S AD3S AD4S AD5S AD6S AD7S RA9 _ROM S R219 3 2 S 2 IC13 IC31 4 _RAM S R220 6 5 R217 R218 IC23 A15S A16S A17S 1 2 3 6 4 5 A B C G1 _G2A _G2B _Y0 _Y1 _Y2 _Y3 _Y4 _Y5 _Y6 _Y7 15 14 13 12 11 10 9 7 _RD S _WR S S G 1 S A0S A1S A2S IC31 1 3 2 1 _G2B _G2A G1 C B A _Y7 _Y6 _Y5 _Y4 _Y3 _Y2 _Y1 _Y0 7 9 10 11 12 13 14 15 R226 R225 R224 R209 R210 R211 _DESK _VTC _SCC2 _ASIC2 _ASIC1 _MAIL S _RES I/O AD0S AD1S AD2S AD3S AD4S AD5S AD6S AD7S C106 R267 S G
CN1-83 CN1-84 CN1-85 CN1-86 1 2 L LIM 10 9 12 U LIM R271 S G CN1-87 CN1-111 CN1-113 CN1-77 13 IC31 IC31 IC53
SC REM TC REM DB REM MC REM TR6 1 1B 2 E 4 3 2B 2C 4 CN1-81 SSW1 SOURCE 1C 6 CN1-80 PRY REM
PF7 PF6 PF5 PF4 PF3 PF2 PF1 PF0 Vdd GND PD7 PD6 PD5 PD4 PD3 PD2
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65
R216
S G
2
S G FTH CN1-8 C93 R22 R23 Z CROSS SIG CN10-5 C23 S G 1 IC3 R30 R205 S G A22S A21S A20S 2 R206 R140 R141 R142 R204 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
R223
3
R214 TFM CLK TRM REM TFM REM CN1-73 CN1-76 CN1-75
_BD SRM B_ SRM A_ SRM B SRM A RESET CN1-74 CN1-120 CN1-121 CN1-122 CN1-123 CN1-102 _RES I/O _RES SCC2 _RES VTC EACK MAIN _WAIT S R173 RA18
BYTE CNVss _RESET Xin Xout _RD Vss Vcc _HLDA ALE _BHE _WR P117 P116 P115 P114 P113 P112
R172
R174 _RES ENG IC30 L102 14 13 12 11 10 9 8 S G TC CONT TNS CONT CN1-15 CN1-13 S E CN1-103 C TR4 B _RESET L48 Vcc DO VDD LD AO6 CLK AO5 DI AO4 AO1 AO3 AO2 Vss GND 1 2 3 4 5 6 7 S G S G
S G R159 R175
C78
[AD0S-AD7S] CN1-55 CN1-56 CN1-57 CN1-58 CN1-59 CN1-60 CN1-61 CN1-62 L LIM U LIM C53 S G CN1-124 CN1-125 CN1-126 CN1-127 CN1-128 _RES I/O 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 SBFSSOL1 SBFSSOL2 SBFSSOL1 DUPPTSOL DUPFWDSOL _WR S _RD S _RAM S
C69
C62
R146
SC CONT
CN1-14
R136
b7 b6 b5 b4 b3 b2 b1 b0
C92
LD DACLK DI
X3
R143
L97
L87
L84
AN0 P95 P94 A22 A21 A20 P90 P67/TB2in P66/TB1in P65/TB0in INT2 INT1 INT0 P61/TA4in P60/TA4out P57/TA3in P56/TA3out P55/TA2in P54/TA2out RTPC3 RTPC2 RTPC1 RTPC0 P47 P46 P45 P44 P43 I _RDY _HOLD
_CS PB7 PB6 PB5 PB4 PB3 PB2 PB1 GND Vdd PB0 PA0 PA1 PA2 PA3 PA4
A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 DCS D0 D1 D2 D3 D4 D5 D6 D7 P110 P111
RA4
RA5
RA6
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
MODE _RESET SELECT AD0 AD1 AD2 AD3 AD4 AD5 AD6 AD7 GND A0 A1 A2 A3 A4 A5 A6 A7 ALE _RD _WR CS
ASIC 1 IC33
PD1 PD0 _Y3 PE7 PE6 PE5 PE4 PE3 PE2 PE1 PE0 GND PC7 PC6 PC5 PC4 PC3 PC2 PC1 PC0 INITD PA7 PA6 PA5
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41
H.ALM
2
CN1-118 CLM-L
AN1 100 AN2 99 AN3 98 AN4 97 P75 96 P76 95 P77 94 Vss 93 AVss 92 Vref 91 AVcc 90 Vcc 89 DA0 88 CLK0 87 P82 86 TD0 85 DA1 84 P85 83 P86 82 P87 81
11
CN1-119
CLM-U
RA7
F.C SW CN1-9 CN1-10 CN1-33 CN1-34 CN1-35 CN1-36 CN1-37 CN1-38 SSW1 STKSW DUPRSW DUPESW DUPPCSW SBESW ESW FSSW SSW2 SSW3 RSW FSW PFSW4 PFSW3 PFSW2 PFSW1
RA8
A18S A19S
_ASIC1
R168 [A0S-A5S]
C115
25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
[A0S-A7S]
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
S G _RD S _RD S
R114 L65 IC15 22 20 27 10 9 8 7 6 5 4 3 25 24 21 23 2 26 1 28 _OE Vcc C43 _CE _WE R113 A0 C42 14 A1 GND S G A2 11 AD0S A3 I/O0 12 AD1S A4 I/O1 13 AD2S A5 I/O2 15 AD3S A6 I/O3 16 AD4S A7 I/O4 17 AD5S A8 I/O5 18 AD6S A9 I/O6 19 AD7S A10 I/O7 A11 A12 A13 A14
_WR S _WR S
PF7 PF6 PF5 PF4 PF3 PF2 PF1 PF0 Vdd GND PD7 PD6 PD5 PD4 PD3 PD2
C28 C29 R72 S G 24 23 22 21 20 19 18 17 16 15 14 13 1 Vcc _RST 2 _RD _WR 3 _CS A0 4 D0 A1 5 D1 SCK 6 D2 Sout 7 D3 Sin 8 D4 _OE 9 D5 INT 10 D6 Xin 11 D7 Xout 12 GND Vcc IC9 R71 _RES I/O _WR S _682
CN1-94 CN1-95 CN1-93 CN1-96 3 IC3 4 5 IC3 R34 1 S G2 3 X2 6 _RD S A0S A1S
S G A0S A1S A2S A3S A4S A5S A6S A7S A8S A9S A10S A11S A12S A13S A14S A15S A16S A17S A18S 12 11 10 9 8 7 6 5 27 26 23 25 4 28 29 3 2 30 31 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18
A0S A1S
A0S A1S A2S A3S A4S A5S A6S A7S A8S A9S A10S A11S A12S A13S A14S
R119 S G AD0S AD1S AD2S AD3S AD4S AD5S AD6S AD7S A0S A1S A2S
IC10 D0 D1 D2 D3 D4 D5 D6 D7 13 14 15 17 18 19 20 21 AD0S AD1S AD2S AD3S AD4S AD5S AD6S AD7S R52 _ROM S _RD S L40 _RD S _WR S S G _ASIC2 L74
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
R48 R49 R51 R50 R79 R47 R46 R78 R77 R45 R44
22 _CE 24 _OE
C49 C52 CN1-46 CN1-45 CN1-44 CN1-43 CN1-50 CN1-49 CN1-48 CN1-47 CN1-51 CN1-52 CN1-53 CN1-54 R127
C21 R27
S G
25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
_CS PB7 PB6 PB5 PB4 PB3 PB2 PB1 GND Vdd PB0 PA0 PA1 PA2 PA3 PA4
MODE _RESET SELECT AD0 AD1 AD2 AD3 AD4 AD5 AD6 AD7 GND A0 A1 A2 A3 A4 A5 A6 A7 ALE _RD _WR CS
ASIC 2 IC19
PD1 PD0 _Y3 PE7 PE6 PE5 PE4 PE3 PE2 PE1 PE0 GND PC7 PC6 PC5 PC4 PC3 PC2 PC1 PC0 INITD PA7 PA6 PA5
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41
CN1-129 CN1-133
BYPSOL
6
R158 S G CN1-134 CN1-104 CN1-105 CN1-106 CN1-107 CN1-130 CN1-131 CN1-132 CN1-39 CN1-40 CN1-41 CN1-42 BYPPFCL FCL3 FCL2 FCL1 FCL5 FCL4 PFCL-L PFCL-U MC ALM ST ALM PCM LOCK DM LOCK
S G
S G
3-7-17
E A E
E A E
2AD-1 2AD
[A0S-A7S] A0S A1S A2S A3S A4S A5S A6S A7S L53 S G C32 S C33 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 S G R97 IC54 L197 C166 C160 _WR S _RD S _SCC2 16 15 14 13 12 1110 9 8 7 6 5 4 3 2 1 INT SCC2 S IC27 L101 C89 C90 S IC55 L201 C167 C161 S IC6 L37 C24 C25 S IC5 L34 C19 C20 R106 S G R230 S G R122 S G R282 S G R169
2
R98
33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48
3
IC3 FRXD CN1-92 S G FTXD CN1-91 IC3 R33 9 8
S G
R67 R68
R42 10
RxD
CN1-90 S G R32
P12 CNVss _RESET P11 P10 Xin Xout Vss P07 P06 P05 P04 P03 P02 P01 P00
11
D0 _W _R _S BM INTR RD3 TD3 RD2 TD2 RD1 TD1 P16 P15 P14 P13
D1 D2 D3 D4 D5 D6 D7 Vcc A0 A1 A2 A3 A4 A5 A6 A7 PA0 PA1 PA2 PA3 PA4 PA5 PA6 PA7 PB0 PB1 PB2 PB3 PB4 PB5 PB6 PB7
CN1-140 CN1-139 CN1-101 CN1-100 CN1-99 CN1-98 CN1-97 H.ALM CN1-21 _MSYNC CN1-22 CN1-63 CN1-64 CN1-23 CN1-24 CN1-25
S G
R400
S G
R199
S G
R406
S G
R39
S G
R21
3
S IC18 L71 C47 C48 S IC38 L112 C107 C109 S IC35 L106 C100 C101 S IC22 L81 C56 C57 S IC25 L93 C74 C75
IC7
KCARD ENABLE KCARD SET SIG TC SET SIG SET SIG SET SIG
S G
R123
S G
R241
S G
R234
S G
R135
S G
R170
4
IC32 L104 C96 C97 IC23 L85 C63 C64 IC3 L32 C15 C16 IC31 L103 C94 C95 IC2 L31 C12 C13 IC53 L152 C154 C155
TxD
DECK RXD
CN1-27
DECK TXD
CN1-26
R208
S G
R145
S G
R18
S G
R207
S G
R12
S G
R372
3.3 V IC49 3.3 V IC37 3.3 V D1 OG I IC1 S L1 CN10-4 5V L108 C104 C105 L107 C102 C103 L94 C76 C77 L150 C150 3.3 V IC36 3.3 V IC26 L151 C49 S G C153
+
C2 C8 C7 C6 S G R2 R374 R1 R6 R375 S G F G S G C11 C10 C5
+
C1 S G CN10-3 S.G R236 S G R235 S G
R171
S G
R332
S G
R322
L2 CN10-1 E5 V 3.3 V IC51 L147 C142 C143 3.3 V IC52 L148 C144 C145 3.3 V IC46 L142 C135 C136 3.3 V IC47 L143 C137 C138 3.3 V IC50 L146 C140 C141 3.3 V IC45 L141 C133 C134
+
C3
S G
R328
S G
R329
S G
R325
S G
R326
S G
R327
S G
R324
3-7-18 3-7-14
E A E A E A Point Source Ai5050 (MCA) E A A E
E A E
E A E
2AD
B
1 19 2 4 6 8 11 13 15 17 _1G _2G 1A1 1A2 1A3 1A4 2A1 2A2 2A3 2A4
C
1Y1 1Y2 1Y3 1Y4 2Y1 2Y2 2Y3 2Y4 18 16 14 12 9 7 5 3 L130 R298 L129 L131 L134 R360 R359 R358 R294 R293 R296 L183 L182 L181
D
CN3-A9 CN3-A10 CN3-A1 PVSYNC M2 PHSYNC M2 _MCPSEL M2 R277
E
3.3 V L115 3.3 V C112 R270 R261 S G R278 R262 3.3 V R264 S G 7 24 23 22 21 16 15 14 13 18 IC40 VCC _RE _WE _RRES _WRES GND RCK WCK Q0 D0 Q1 D1 D2 Q2 D3 Q3 D4 Q4 D5 Q5 D6 Q6 D7 Q7 5 20 6 19 8 17 1 2 3 4 9 10 11 12
C111
S G
1
R283 R284
+ +
IC49
L56 R105
1 19
2
L173 MCPCLK M1 MCPMREW M1 MCP1DA M1 MCP1DB M1 CN2-A11 L174 CN2-A12 L175 CN2-A14 L176 CN2-A16
_1G _2G 1A1 1A2 1A3 1A4 2A1 2A2 2A3 2A4 1Y1 1Y2 1Y3 1Y4 2Y1 2Y2 2Y3 2Y4 18 16 14 12 9 7 5 3
R265 R266
3.3 V
2 4 6 8 11 13 15 17 S G
S G
R5 R4 R3
S G R286 S G S G 3.3 V
+
S G
IC48
_RES VTC
3.3 V
_RES VTC
R315
R285
3
C117 R272 C118
IC2 6 R14
R15 D2 C14
C129
100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76
S G
S G
VSS D5 D6 D7 VSS VDD PPST _LDON _LDEN N.C XI XO VSS CLK VSS MSYNC PMCLK VDD BD _FLDEN _ADJUST VSS -LDOUTA _LDOUTB VSS
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
R279 C124
VDD A0 A1 A2 A3 VSS A4 A5 _VTCCS _IORD _IOWR VDD D0 D1 D2 VSS SMC SIN SOT VSS D3 D4 VSS SCK VDD
VSS TEST3 TEST2 TEST1 VSS TEST0 P7 VDD P6 P5 P4 P3 VSS _RESET VSS _NSCLE _SCLE _NSCDE _SCDE VDD N.C LSUOUT VSS PVCLK VSS
3.3 V L119
IC42
VDD VSS _PVD0O _PVDAO VSS _PHSYNC VDD AMC _PVSYNC PVSYNC VSS SEL0 SEL1 VDD _SEL2 _SEL3 _SEL4 _SEL5 _SEL6 VSS P2 P1 P0 FLDON VDD
D FET1 R317 PHSYNC_ R316 PVSYNC_ F.C SW 9 IC38 11 8 L11 SLEEP 9 3.3 V
S
CN1-70 IC38 10
4
L3 CN7-13 CN8-5 CN7-1 L16 LSU5 V G (5 V) G (5 V) G (5 V) G (5 V) G (5 V) PM START
SELMCP2_ SELMCP1_
10 L18
CN7-6 CN7-8
IC24
R297
R303
L149
R19
C123
26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
S G
IC4 L33 4 12 1 7 9 15 16 8 S G EN DO1+ EN DO1 DI1 DO2+ DI2 DO2 DI3 DO3+ DI4 DO3 VCC DO4+ GND DO4 2 3 6 5 10 11 14 13
L15 CN7-5 L14 CN7-4 L13 CN7-3 L12 CN7-2 L19 _VD1 _VD2+ _VD2 _VD1+
R299
R17
R37
[A0S-A5S] IC39
R300
R35
_MSYNC
_VTC _RD S AD7S AD6S AD5S AD4S AD3S AD2S AD1S AD0S [AD0S-AD7S]
19 1 2 3 4 5 6 7 8 9
_OE T_R A7 A6 A5 A4 A3 A2 A1 A0 B7 B6 B5 B4 B3 B2 B1 B0 18 17 16 15 14 13 12 11 D7S D6S D5S D4S D3S D2S D1S D0S
S
PPST _LDON _LDEN R255 R256 R257 R258 R259 R260 R275 R276 3.3 V
_BD
L135 4 C125 R292 S G R291 SLEEP_ R290 _RES VTC S G ST GND 1 2 S G C126 3
10 L21
CN7-9 CN7-11
VDD OUT X5
12
L17 CN7-7
5 2B 2 1B
2 1B
3-7-19 3-7-15
E A E A A E Point Source Ai5050 (MCA) E A A E
E A E
E A E
2AD-1 2AD
1
L83 SID 0+ SID 0 SID 1+ SID 1 SID 2+ SID 2 CN5-1 CN5-3 CN5-5 L73 CN5-7 L69 CN5-9 CN5-11 CN5-13 CN5-15 L58 SID 4+ SID 4 SID 5+ SID 5 SID 6+ CN5-17 CN5-19 CN5-21 CN5-23 CN5-25 CN5-27 CN5-29 CN5-31 L75 CN5-6 CN5-8 CN5-2 CN5-4 CN5-10 CN5-12 L72 L82 L79 L68 L66 R120 R131 R124 L55 L52 L51 L47 L45 L43 L39 R43 R69 R99 R102 L67 L64 L60 R111 R121 L80 L76 R125 R132
SLEEP IC14 2 1 6 7 10 9 14 15
IN1+ EN IN1 EN IN2+ OUT1 IN2 OUT2 IN3+ OUT3 IN3 OUT4 IN4+ VCC IN4 GND
R289 15 1 2 3 5 6 11 10 14 13
IC51 _G S 1A 1B 2A 2B 3A 3B 4A 4B 1Y 2Y 3Y 4Y 4
1
R364 L187 CN3-B8 L188 CN3-B9 L189 CN3-B10 M2 DATA2 L190 CN3-B11 M2 DATA3 R398 L207 RxD MCP2 CN3-A5 L209 MCP2 ACK 4 R368 7 R369 9 R370 12R371 L191 CN3-B12 M2 DATA4 L192 CN3-B13 M2 DATA5 L193 L194 CN3-B14 M2 DATA6 CN3-B15 M2 DATA7 W RDY MCP2 R RDY MCP2 CN3-A8 L157 CN3-A7 C157 S G SLEEP TxMCP1 MACK MCP1 _RES M1 4 R363 7 R362 9 R361 12 SEMCP MCP1 W RDY MCP1 R RDY MCP1 CN2-B1 L158 CN2-A8 L196 R387 R382 C156 R383 C158 S G
S G S G
IC55 1 19
S G
_1G _2G 1A1 1A2 1A3 1A4 2A1 2A2 2A3 2A4 1Y1 1Y2 1Y3 1Y4 2Y1 2Y2 2Y3 2Y4 18 16 14 12 9 7 5 3
SID 3+ SID 3
IC8 2 1 6 7 10 9 14 15
IN1+ EN IN1 EN IN2+ OUT1 IN2 OUT2 IN3+ OUT3 IN3 OUT4 IN4+ VCC IN4 GND
4 12 3 5 11 13 16 8 C30
L49
2 4 6 8 11 13 15 17
RxMCP2 MCP2ACK _SET M2 _WRDY M2 _RRDY M2 CN3-A4 CN3-A13 CN3-A15 CN3-B6 CN3-B7 CN3-B16
SEMCP MCP2
RA1 C31
R76
S G
3
TxD MCP1 ENGACK MCP1 RESET MCP1
IC54 1 19
S G
IC20 2 1 6 7 10 9 14 15
IN1+ EN IN1 EN IN2+ OUT1 IN2 OUT2 IN3+ OUT3 IN3 OUT4 IN4+ VCC IN4 GND
IC50 15 1 SMRE SOVSYNC SCNCLK 2 SMRE PMRE 3 SOVSYNC_ 5 POVSYNC_ 6 SCNCLK 11 PRTCLK 10 14 13
S G
_1G _2G 1A1 1A2 1A3 1A4 2A1 2A2 2A3 2A4 1Y1 1Y2 1Y3 1Y4 2Y1 2Y2 2Y3 2Y4 18 16 14 12 9 7 5 3
4 12 3 5 11 13 16 8 C50
L77
_G S 1A 1B 2A 2B 3A 3B 4A 4B 1Y 2Y 3Y 4Y
L186 CN3-B5 L185 CN3-B4 L184 CN3-B3 WCK M2 OVSYNC M2 MCP1 ACK CN2-A3 MRE M2 RxD MCP1 CN2-A5
RA10 C51
2 4 6 8 11 13 15 17
RxMCP1 MCP1ACK _SET M1 _WRDY M1 _RRDY M1 CN2-A4 CN2-A13 CN2-A15 CN2-B6 CN2-B7 CN2-B16
R126 L63 CN5-14 CN5-30 CN5-34 CN4-1 CN4-4 CN4-7 CN4-13 CN4-15 CN4-17 CN4-19 CN4-21 CN4-26
S G
S
R323 15 1 2 3 5 6 11 10 14 13
L138
S G
IC46 _G S 1A 1B 2A 2B 3A 3B 4A 4B 1Y 2Y 3Y 4Y
CN2-A7
L140 3.3V IC37 _1G _2G 1A1 1A2 1A3 1A4 2A1 2A2 2A3 2A4 1Y1 1Y2 1Y3 1Y4 2Y1 2Y2 2Y3 2Y4 18 16 14 12 9 7 5 3
L162 CN2-B8 L163 CN2-B9 L164 CN2-B10 M1 DATA2 L165 CN2-B11 M1 DATA3 PRT ACK _PRINT CN4-6 L95 CN4-8 L98 R181 R180 R157 R156 CN4-9 L86 CN4-11 R178 R177 M1 DATA1 RxD PRT CN4-2 L91 R167 L88 M1 DATA0 3.3V R162 R161 R160 C70 C71 C79 C80 R165 R176 R179 R155
S G
1 19 2 4 6 8 11 13 15 17
IC27 _1G _2G 1A1 1A2 1A3 1A4 2A1 2A2 2A3 2A4 1Y1 1Y2 1Y3 1Y4 2Y1 2Y2 2Y3 2Y4 18 16 14 12 9 7 5 3 R151 R150 R152 R153 R154
5
RxPRT PRTACK _PRINT _SETPRT _P1
R166
1 19
S G
L128 PID 0 PID 1 CN4-22 CN4-23 CN4-24 L120 PID 3 PID 4 PID 5 PID 6 PID 7 CN4-25 CN4-27 CN4-28 L110 CN4-29 CN4-30 L111 L116 L113 L124 L125
PID 2
2 4 6 8 11 13 15 17
RA20
PID0 PID1 PID2 PID3 PID0 PID1 PID2 PID3 PID4 PID5 PID6 PID7
_SETPRT _P1 CN2-B12 M1 DATA4 L167 CN2-B13 M1 DATA5 L168 CN2-B14 M1 DATA6 L169 CN2-B15 M1 DATA7
R342
L166
6
IC26 _1G _2G 1A1 1A2 1A3 1A4 2A1 2A2 2A3 2A4 1Y1 1Y2 1Y3 1Y4 2Y1 2Y2 2Y3 2Y4 18 16 14 12 9 7 5 3 L133 L137 L121 L117 L114 CN4-5 CN4-3 CN4-10 CN4-12 CN4-14 TxD PRT ENGACK PRT _MRDY _P2 _PRTRST
RA21
7
L127 PMRE _POVSYNC PRTCLK CN4-20 CN4-18 CN4-16 L132 L136
IC45 15 1 IC36 _G S 1A 1B 2A 2B 3A 3B 4A 4B 1Y 2Y 3Y 4Y 4 7 R337 R336 L161 CN2-B5 L160 CN2-B4 L159 CN2-B3 WCK M1 OVSYNC M1 MRE M1
1 19 2 4 6 8 11 13 15 17
S G
_1G _2G 1A1 1A2 1A3 1A4 2A1 2A2 2A3 2A4 1Y1 1Y2 1Y3 1Y4 2Y1 2Y2 2Y3 2Y4 18 16 14 12 9 7 5 3
RA19
2 3 5 6 11 10 14 13
9 R335 12
S G
3-7-20 3-7-16
E A E A E A Point Source Ai5050 (MCA) E A A E
2AD
VCC3
1
_MCPSEL _RVST _PHSYNC
1
U10
_G A1 A2 A3 A4 Y1 Y2 Y3 Y4
(003-15A)
2
TXDMCP ACKMCP _R_READY _W_READY CN1 a5 CN1 a3 CN1 a7 CN1 a8
2
iTXDMCP 19 11 13 15 17 GPL5 19 11 13 15 17 R49 3 4 2 1 RA19 iMREVDOUT iVD1 iVD2 49 43 44 iACKMCP iRREADY_ iWREADY_ 71 69 68 (002-15I)
9 7 5 3
Y1 Y2 Y3 Y4
A1 A2 A3 A4
RCK
U10
_G Y1 Y2 Y3 Y4 A1 A2 A3 A4
iRCK2
(011-13F)
iSETMCP_ ACKENG CN1 a6 L29 R22 2 1 RA5 CN1 a2 L26 R18 2 1 RA1 CN1 b2 L10 R5 VCC3 2 1 RA2 3 4 C9 GPL5 GPL5 3 4 C13 3 4 C14 1 2 4 6 8 U8
_G A1 A2 A3 A4 Y1 Y2 Y3 Y4
72
4
R27 18 16 14 12 R31 iACKENG 70 iTXDENG iRESET_ (002-15I) (011-14D)
TXDENG
_RESET
5
WCK
CN1 b3
L11
R19
_WVST
CN1 b4
L12
R20
2 1 RA3
1 2 4 6 8
U7
_G A1 A2 A3 A4 Y1 18 Y2 16 Y3 14 Y4 12
64 67 66 VCC3
MREID
CN1 b5 CN1 a4 CN1 a13 CN1 a15 CN1 b6 CN1 b7 CN1 b16 CN1 b8 CN1 b9 CN1 b10 CN1 b11 CN1 b12 CN1 b13 CN1 b14 CN1 b15
L13 L6 L7 L8 L14 L15 L24 L16 L17 L18 L19 L20 L21 L22 L23
R21
VCC3
6
19 11 13 15 17 GPL5 U7
_G A1 A2 A3 A4 Y1 Y2 Y3 Y4
8 7 6 5
RA10
RA9
8 7 6 5
GPL5
0 7 1 6 2 5 3 4 18 16 14 12 0 1 2 3
RA12 1 2 3 4 RA11 1 2 3 4
8 7 6 5 8 7 6 5
53 62 54 61 55 60 56 59
R24
U9
9 7 5 3
1 2 3 4
0 7 1 6
2 5 3 4
1 2 3 4
0 1 2 3 4 5 6 7 ID0(7:0) 0 1 2 3
1 2 4 6 8 19 4 5 6 7
_G A1 A2 A3 A4 Y1 Y2 Y3 Y4
U9
_G Y1 Y2 Y3 Y4
IDP(7:0) 9 7 5 3 4 5 6 7
11 A1 13 A2 15 A3 17 A4
GPL5
3-7-21
2AD
VPL5
VPL5
1
(003-15A)
1
VPL5 1 4 2 VPL5 K U12 LD1 A R52 VPL5
8 7 6 5
RA23 1 2 3 4
DSACY
R50 8 7 6 5
RA24 1 2 3 4
8 7 6 5
VPL5
8 7 6 5
RA22 1 2 3 4
RA26
2
(011-13I) (011-13C) CPUCLK RST_
C46
C47
C48
2
R53 R54 VPL5 VPL5
1 2 3 4
GPL5
L61
L62
L64
L65
3
109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144
RMC_ W_R SIZ1 SIZ0 DS_ AS_ BGACK_ BG_ BR_ BERR_ HALT_ RESET_ GND11 CLKOUT VCC11 XFC VCC10 EXTAL VCCSYN XTAL GND10 MODCK VCC9 IPIPE_ IFEICH BKPT_ FREEZE TIN1 TOUT1 TGATEL TCK TMS TDI TDO VCC8 GND9
C52
0 31 30 29 28 15 14 13 12 RA35 1 2 3 4 8 7 6 5 15 14 13 12 27 26 25 24 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
11 10 9 8
RA43 1 2 3 4
8 7 6 5
11 10 9 8
7 6 5 4
RA47 1 2 3 4
8 7 6 5
7 6 5 4
5
3 2 1 0 RA50 1 2 3 4 8 7 6 5 3 2 1 0
$002
CS0_ IRO1_ IRO2_ IRO3_ IRO4_ GND1 VCC1 IRO5_ IRO6_ IRO7_ DONE2_ DACK2_ DREO2_ DONE1_ DACK1_ DREO1_ X1 GND2 VCC2 X2 SCLK CTSB_ RTSB_ TXDB RXDB TXRAYA_ RARDYA_ CTSA_ RTSA_ GND3 VCC3 TXDA RXDA TIN2 TOUT2 TGATE2
GND12 VCC12 DSACK1_ DSACK0_ A0 A31 A30 A29 A28 GND13 VCC13 A27 A26 A25 A24 D15 D14 D13 GND14 D12 GND15 VCC14 D11 D10 D9 D8 D7 D6 D5 D4 GND16 VCC15 D3 D2 D1 D0
U17
FC3 FC2 FC1 FC0 VCC7 GND8 A23 A22 A21 A20 A19 A18 A17 VCC6 GND7 A16 A15 A14 GND6 A13 A12 A11 VCC5 GND5 A10 A9 A8 A7 A6 A5 A4 VCC4 GND4 A3 A2 A1
72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37
23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 28 29 30 31 RA29 1 2 3 4 8 7 6 5 28 29 30 31 15 14 13 12 RA41 1 2 3 4
GPL5
R59
C44
C45
C59
C60
4
A (31:0) $001
8 7 6 5
15 14 13 12
24 25 26 27
RA32 1 2 3 4
8 7 6 5
24 25 26 27
11 10 9 8
RA45 1 2 3 4
8 7 6 5
11 10 9 8
23 22 21 20
RA31 1 2 3 4
8 7 6 5
23 22 21 20
7 6 5 4
RA49 1 2 3 4
8 7 6 5
7 6 5 4
19 18 17 16
RA34 1 2 3 4
8 7 6 5
19 18 17 16
3 2 1 0
RA53 1 2 3 4
8 7 6 5
3 2 1 0
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36
A0 (31:0) iTXDENG VPL5 TP10 261 CS0 R65 8 7 6 5 8 7 6 5 8 7 6 5 R63 R61 VPL5 VPL5 VPL5 B4B-PH-KL NONE CN3 1 VCCMON CN3 2 CN3 3 CN3 4 TXDMON RXDMON GNDMON R69 iTXDMCP (001-13C) (001-13F)
RA54 1 2 3 4
RA59
RA58
8 7 6 5
RA27
1 2 3 4
1 2 3 4
1 2 3 4
R62
$001 $002
A CPUD
C64
X3
C65
8
GPL5 GPL5
3-7-22
2AD
MCP2AC (304:1) 226 224 223 222 221 219 218 217 216 214 213 212 211 208 206 204 201 199 197 195 193 188 186 184 181 180 179 178 177 176 175 174 173 170 169 168 166 165 164 163 162 161 160 159 158 157 156 155
$004
VCC3 L59 228 227 226 225 224 223 222 221 220 219 218 217 216 215 214 213 212 211 210 209 208 207 206 205 204 203 202 201 200 199 198 197 196 195 194 193 192 191 190 189 188 187 186 185 184 183 182 181 180 179 178 177 176 175 174 173 172 171 170 169 168 167 166 165 164 163 162 161 160 159 158 157 156 155 154 153
C62
249 251 252 253 256 257 258 259 260 261
263 264
269 270 272 273 276 277 280 281 283 284 287 288 290 291
293 294 295 296 297 298 299 300 301 302
13
15 16 17 18
21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36
41
43 44
46 47 48
50 51
53 54 55 56
59 60 61 62
64
66 67 68 69 70 71 72
$001 MCP2AC
(001-13B) (002-02A) (004-03B) (005-03B) (006-03B) (007-01B) (008-01B) (009-01B) (010-02H) (011-04F) (011-13I) (011-13F)
74
3 4 5 6
8 9
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76
GND1 GND2 RDBWR SIZE1 SIZE0 ASB VDD1 A1 A2 SMC AMC SIN A3 SOUT A4 A5 A6 A7 VDD2 GND3 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 A20 A21 A22 A23 VDD3 VDD4 GND4 GND5 RCK GND6 VD1 VD2 VDD5 RCKENB MCPSELB MREVDIN MREVDOUT PWSYNCB RVSIB GND7 ID0 ID1 ID2 ID3 VDD6 GND8 ID4 ID5 ID6 ID7 GND9 WCK GND10 MRE10 WVS1B WREADYB RREADYB ACKENG ACKMCP SETMCPB VDD7 RESETB GND11 GND12
229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304
GND46 GND45 SWEB GND44 SRAS21B SRAS11B SRAS20B SRAS10B VDD25 SCAS21B SCAS11B SCAS20B SCAS10B GND43 SRAS22B SRAS12B SRAS23B SRAS13B GND42 VDD24 SA9 GND41 SA8 GND40 SA7 GND39 VDD23 SA10 GND38 SA6 GND37 SA5 GND36 SA4 GND35 SA3 GND34 GND33 VDD22 VDD21 SA2 GND32 SA1 GND31 SA0 GND30 VDD20 Q2CDWRB Q2CDRDB Q2CDACKB Q2CDRD Q2PDWRB Q2PDRDB Q2DACKB Q2PDRQ Q2HINTR GND29 VDD19 Q2HWRB Q2HRDB Q2HCSB VDD18 Q1CDWRB Q1CDRDB Q1CDACKB Q1CDRQ Q1PDWRB Q1PDRDB Q1PDACKB Q1PORQ Q1HINTR Q1HWRB Q1WRDB Q1MCSB GND28 GND27
VDD26 VDD27 SMLLD SMLDEB SMGHDEB SMGLDEB SMGDIP VDD28 SRAS30B SRAS31B SRAS32B SRAS33B SCAS30B SCAS31B GND47 RAMCSHB RAMCSLB RAMDEB GND48 GND49 CLK GND50 RAMWEB RDMCSB RDEMCEB VDD29 IRDALLB IRD5B IRD4B IRD3B IRD2B IRD1B CS0B GND51 CPUD0 CPUD1 VDD30 VDD31 GND52 GND53 CPUD2 CPUD3 GND54 CPUD4 CPUD5 VDD32 GND55 CPUD6 CPUD7 VDD33 GND56 CPUD8 CPUD9 GND57 CPUD10 CPUD11 GND58 GND59 CPUD12 CPUD13 GND60 CPUD14 CPUD15 GND61 A24 A25 A26 A27 A28 A29 A30 A31 A0 DSACKB VDD34 VDD35
U16
VDD17 VDD16 DRAMD24 DRAMD23 DRAMD25 DRAMD22 GND26 VDD15 DRAMD26 DRAMD21 DRAMD27 DRAMD20 GND25 VDD14 DRAMD28 DRAMD19 DRAMD29 DRAMD18 GND24 GND23 DRAMD30 DRAMD17 DRAMD31 DRAMD16 GND22 DRAS5B DRAS4B DRAS3B DRAS2B DRAS1B DRAS6B GND21 DA4 DA3 DA5 DA2 GND20 GND19 VDD13 VDD12 DA6 DA1 DA7 DA0 DA8 DA9 GND18 DOEB DWEB DCASHB DCASLB GND17 DRAMD8 DRAMD7 DRAMD9 DRAMD6 GND16 GND15 DRAMD10 DRAMD5 DRAMD11 DRAMD4 GND14 VDD11 DRAMD12 DRAMD3 DRAMD13 DRAMD2 GND13 VDD10 DRAMD14 DRAMD1 DRAMD15 DRAMD0 VDD9 VDD8
152 151 150 149 148 147 146 145 144 143 142 141 140 139 138 137 136 135 134 133 132 131 130 129 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 104 103 102 101 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77
C61
2
C43 L69
C41 138 137 136 135 132 131 130 129 127 126 125 124 123 122 120 119 118 117
C63
L68
3
C51
C42
L60
C50
4
R58 C49
112 111 110 109 108 107 105 104 103 102 100 99 98 97 94 93 92 91 88 87 86 85 82 81 80 79
GPL5
3-7-23
2AD
1
$001 CPUD (15:0) SD (15:0)
(002-15F)
A (31:0)
(003-15A)
MCP2AC (304:1) 301 8 9 13 15 16 17 18 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 293 294 295 296 297 298 299 300 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 A20 A21 A22 A23 A24 A25 A26 A27 A28 A29 A30 A31 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 VPL5 L38 0 1 2 3 RA17 1 2 3 4 8 7 6 5 0 1 2 3 R17 4 5 6 7 RA18 1 2 3 4 8 7 6 5 4 5 6 7 C7 C12 R15 VPL5 L39 C6 C8
8 9 10 11
1 2 3 4
RA7
8 8 7 9 6 10 5 .11 8 9 10
15 13 8 7 6 5 4 3 2 1
12 13 14 15
1 2 3 4
RA8
8 7 6 5
12 13 14 15
1 2 3 4 5 6 7 8 9 10 11 12 13 14
VCC WE_ A13 A8 A9 A11 OE_ A10 CE_ IO8 IO7 IO6 IO5 IO4
28 27 26 25 24 23 22 21 20 19 18 17 16 15
14 9 10 12 11 15 14 13 12 11
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
GPL5
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
VPP CE0 D15 D14 D13 D12 D11 D10 D9 D8 GND1 D7 D6 D5 D4 D3 D2 D1 D0 OE0 U1
VCC A17 A16 A15 A14 A13 A12 A11 A10 A9 GND2 A8 A7 A6 A5 A4 A3 A2 A1 A0
40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21
18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
VPL5 GPL5 L47 263 264 269 270 272 273 276 277 280 281 283 284 287 288 290 291 CPUD0 CPUD1 CPUD2 CPUD3 CPUD4 CPUD5 CPUD6 CPUD7 CPUD8 CPUD9 CPUD10 CPUD11 CPUD12 CPUD13 CPUD14 CPUD15 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 R43 C30 C33
GPL5
15 13 8 7 6 5 4 3 2 1 0 1 2
6
TP4 RA52 1 2 3 4 TP5 TP3 TP1 GPL5
1 2 3 4 5 6 7 8 9 10 11 12 13 14
VCC WE_ A13 A8 A9 A11 OE_ A10 CE_ IO8 IO7 IO6 IO5 IO4
28 27 26 25 24 23 22 21 20 19 18 17 16 15
5
14 9 10 12 11 7 6 5 4 3
8 7 6 5 TP2 TP6
RA46 1 2
4 3
$001 CPUD
3-7-24
2AD
1
(003-15A) MCP2AC (304:1) 208 SA9 206 SA8 204 SA7 RA63 1 2 3 4 8 7 6 5 LSA1 (10:0) 9 8 7 0 1 RA62 1 2 3 4 2 3 4 RA61 1 2 3 4 5 6 7 CN5 12 CN5 13 CN5 14 CN5 15 CN5 16 CN5 17 CN5 18 CN5 28 CN5 31 CN5 32 CN5 19 CN5 44 CN5 45 CN5 34 CN5 33 CN5 40 CN5 43 CN5 41 CN5 42 226 SWE_ R66 CN5 47 CN5 10 VPL5 L5 CN5 30 CN5 59 8 SM1A0 24 CN5 50 SM1A1 9 SM1A2 25 CN5 52 SM1A3 10 CN5 53 SM1A4 26 CN5 54 SM1A5 11 CN5 55 SM1A6 27 CN5 56 SM1A7 12 CN5 57 SM1A8 28 CN5 58 SM1A9 29 CN5 60 SM1A10 13 CN5 61 SM1RAS0_ 30 CN5 62 SM1RAS1_ 14 CN5 63 SM1RAS2_ 31 CN5 64 SM1RAS3_ 15 CN5 65 SM1CAS0_ SM1CAS0_ SM1CAS1_ SM1CAS1_ SM1WE_ SM1VCC SM1VCC SM1VCC SIMMD (31:0) CN5 51
CN5 49
SM1D8 SM1D24 SM1D9 SM1D25 SM1D10 SM1D26 SM1D11 SM1D27 SM1D12 SM1D28 SM1D29 SM1D13 SM1D30 SM1D14 SM1D31 SM1D15
CN5 2
SM1D0 SM1D16 SM1D1 SM1D17 SM1D2 SM1D18 SM1D3 SM1D19 SM1D4 SM1D20 SM1D5 SM1D21 SM1D6 SM1D22 SM1D7 SM1D23
16 CN5 3 1 CN5 4
8 7 6 5
10 6 5 4
17 CN5 5 2 CN5 6
18 CN5 7 3 CN5 8
8 7 6 5
3 2 1 0
19 CN5 9 4 CN5 20
8 9 10 223 221 213 211 SRAS11_ SRAS10_ SRAS12_ SRAS13_ RA64 1 2 3 4 SRAS1 (3:0) 8 7 6 5 1 0 2 3 0 1 2 3 RA71 216 SCAS10_ 1 218 SCAS11_ 2 3 4 0 1 SCAS1 (1:0) 0
20 CN5 21 5 CN5 22
21 CN5 23 6 CN5 24
22 CN5 25 7 CN5 26
23 CN5 27
$001
6
C87
F3 CN5 1 CN5 39
SIMM SLOT1
C85
C86
C88
CE9
CE10
CE11
R80
CN5 72
GPL5
$001
SIMMD
3-7-25
2AD
1
(003-15A) MCP2AC (304:1) 208 SA9 205 SA8 204 SA7 RA85 1 2 3 4 8 7 6 5 LSA2 (10:0) 9 8 7 0 1 RA84 1 2 3 4 2 3 4 RA83 1 2 3 4 5 6 7 CN4 12 CN4 13 CN4 14 CN4 15 CN4 16 CN4 17 CN4 18 CN4 28 CN4 31 CN4 32 CN4 19 CN4 44 CN4 45 CN4 34 CN4 33 CN4 40 CN4 43 CN4 41 CN4 42 R67 CN4 47 CN4 10 VPL5 L4 CN4 30 CN4 59 8 SM2A0 24 CN4 50 SM2A1 9 SM2A2 25 CN4 52 SM2A3 10 CN4 53 SM2A4 26 CN4 54 SM2A5 11 CN4 55 SM2A6 27 CN4 56 SM2A7 12 CN4 57 SM2A8 28 CN4 58 SM2A9 29 CN4 60 SM2A10 13 CN4 61 SM2RAS0_ 30 CN4 62 SM2RAS1_ 14 CN4 63 SM2RAS2_ 31 CN4 64 SM2RAS3_ 15 CN4 65 SM2CAS0_ SM2CAS0_ SM2CAS1_ SM2CAS1_ SM2WE_ SM2VCC SM2VCC SM2VCC SIMMD (31:0) CN4 51
CN4 49
SM2D8 SM2D24 SM2D9 SM2D25 SM2D10 SM2D26 SM2D11 SM2D27 SM2D12 SM2D28 SM2D29 SM2D13 SM2D30 SM2D14 SM2D31 SM2D15
CN4 2
SM2D0 SM2D16 SM2D1 SM2D17 SM2D2 SM2D18 SM2D3 SM2D19 SM2D4 SM2D20 SM2D5 SM2D21 SM2D6 SM2D22 SM2D7 SM2D23
16 CN4 3 1 CN4 4
8 7 6 5
10 6 5 4
17 CN4 5 2 CN4 6
18 CN4 7 3 CN4 8
8 7 6 5
3 2 1 0
19 CN4 9 4 CN4 20
8 9 10 224 222 214 212 SRAS21_ SRAS20_ SRAS22_ SRAS23_ RA65 1 2 3 4 SRAS2 (3:0) 8 7 6 5 1 0 2 3 0 1 2 3 RA70 217 SCAS20_ 1 219 SCAS21_ 2 4 3 SCAS2 (1:0) 0 1 0
20 CN4 21 5 CN4 22
21 CN4 23 6 CN4 24
22 CN4 25 7 CN4 26
23 CN4 27
SWE_
$001
6
C81
F2 CN4 1 CN4 39
SIMM SLOT2
C79
C80
C82
CE6
CE7
CE8
R79
CN4 72
GPL5
$001
SIMMD
3-7-26
2AD D
VPL5 VPL5 VPL5
E
VPL5 VPL5
F
VPL5 VPL5
8 7 6 5
8 7 6 5
8 7 6 5
8 7 6 5
8 7 6 5
8 7 6 5
8 7 6 5
RA37 1 2 3 4
RA38 1 2 3 4
RA39 1 2 3 4
RA40 1 2 3 4
RA13 1 2 3 4
RA14 1 2 3 4
RA15 1 2 3 4
31 30 29 28
27 26 25 24
23 22 21 20
19 18 17 16
15 14 13 12
11 10 9 8
7 6 5 4
MCP2AC (304:1) 150 149 148 147 DRAMD24 DRAMD23 DRAMD25 DRAMD22 RA60 1 2 3 4 8 7 6 5 24 23 25 22
DD (31:0) 31 30 29 28 8 7 6 5 RA72 1 2 3 4 31 30 29 28
3 2 1 0
RA16 1 2 3 4
8 7 6 5
QDD (31:0)
L63
RA57 1 2 3 4
R57 8 7 6 5 26 21 27 20 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 5 2 3 4 5 7 8 9 10 33 34 35 36 38 39 40 41 31 30 14 29 13 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 D14 D15 D16 LCAS0 UCAS0 RAS0 OE0 W0 VSS1 VCC1 VSS2 VCC2 VSS3 VCC3 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 NC1 NC2 NC3 NC4 NC5
C53 27 26 25 24 8 7 6 5
RA73 1 2 3 4
27 26 25 24
RA55 1 2 3 4
8 7 6 5
28 19 29 18
RA51 1 2 3 4
8 7 6 5
30 17 31 16
100 99 98 97
RA28 1 2 3 4
8 7 6 5
8 7 9 6
42 1 37 6 22 21 28 27 26 25 24 23 20 19 18 17 11 12 15 16 32
9 8 7 6 5 4 3 2 1 0 3
16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
2 3 4 5 7 8 9 10 33 34 35 36 38 39 40 41 31 30 14 29 13
D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 D14 D15 D16 LCAS0 UCAS0 RAS0 OE0 W0
VSS1 VCC1 VSS2 VCC2 VSS3 VCC3 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 NC1 NC2 NC3 NC4 NC5
42 1 37 6 22 21 28 27 26 25 24 23 20 19 18 17 11 12 15 16 32
9 8 7 6 5 4 3 2 1 0 1
16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
2 3 4 5 7 8 9 10 33 34 35 36 38 39 40 41 31 30 14 29 13
D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 D14 D15 D16 LCAS0 UCAS0 RAS0 OE0 W0
VSS1 VCC1 VSS2 VCC2 VSS3 VCC3 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 NC1 NC2 NC3 NC4 NC5
42 1 37 6 22 21 28 27 26 25 24 23 20 19 18 17 11 12 15 16 32
9 8 7 6 5 4 3 2 1 0
23 22 21 20
8 7 6 5
RA74 1 2 3 4
23 22 21 20
19 18 17 16
8 7 6 5
RA75 1 2 3 4
19 18 17 16
15 14 13 12
8 7 6 5
RA76 1 2 3 4
15 14 13 12
94 93 92 91
RA25 1 2 3 4
U20
8 10 7 5 6 11 5 4 R47 8 12 7 3 6 13 5 2 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 4 2 3 4 5 7 8 9 10 33 34 35 36 38 39 40 41 31 30 14 29 13 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 D14 D15 D16 LCAS0 UCAS0 RAS0 OE0 W0 VSS1 VCC1 VSS2 VCC2 VSS3 VCC3 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 NC1 NC2 NC3 NC4 NC5 42 1 37 6 22 21 28 27 26 25 24 23 20 19 18 17 11 12 15 16 32 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 2 2 3 4 5 7 8 9 10 33 34 35 36 38 39 40 41 31 30 14 29 13 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 D14 D15 D16 LCAS0 UCAS0 RAS0 OE0 W0 L58 C38 C35 GPL5
U19
L57 C39 R48 C36 GPL5
U18
L56 C37 R46 C34 7 6 5 4 VSS1 VCC1 VSS2 VCC2 VSS3 VCC3 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 NC1 NC2 NC3 NC4 NC5 42 1 37 6 22 21 28 27 26 25 24 23 20 19 18 17 11 12 15 16 32 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 0 2 3 4 5 7 8 9 10 33 34 35 36 38 39 40 41 31 30 14 29 13 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 D14 D15 D16 LCAS0 UCAS0 RAS0 OE0 W0 VSS1 VCC1 VSS2 VCC2 VSS3 VCC3 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 NC1 NC2 NC3 NC4 NC5 42 1 37 6 22 21 28 27 26 25 24 23 20 19 18 17 11 12 15 16 32 8 7 6 5 GPL5 11 10 9 8 8 7 6 5
RA77 1 2 3 4
11 10 9 8
88 87 86 85
RA21 1 2 3 4
RA78 1 2 3 4
7 6 5 4
82 81 80 79
RA20 1 2 3 4
8 14 7 1 6 15 5 0
1 2 RA48
4 3
5 4
9 8 7 6 5 4 3 2 1 0
9 8 7 6 5 4 3 2 1 0
9 8 7 6 5 4 3 2 1 0
3 2 1 0
8 7 6 5
RA79 1 2 3 4
3 2 1 0
RA44 1 2 3 4
8 7 6 5
3 2 1 0
U15
GPL5 105 104 103 102 DOE_ DWE_ DCASH_ DCASL_ RA30 1 2 3 4 DRAS_ (5:0) 8 7 6 5 LDA (9:0)
U14
GPL5
U13
GPL5
RA33 1 2 3 4
8 7 6 5
7 0 8 9
7
VPL5 L3
RA36 1 2
4 3
6 1
F1
CE3
CE5
RA42 1 2 3 4
8 7 6 5
4 3 5 2
CE4
8
GPL5
3-7-27
2AD
1
(009-15B)
QSD (31:0)
(003-15A)
MCP2AC (304:1)
31 30 29 28
27 26 25 24 23
22 21 20 19 18
17 16 15 14 13
12 11 10 9 8
163
Q1CDRQ
R78
$002
2
RA69 1 2 3 4 R77 0 1 2 3 4 5 6 7 108 107 106 105 104 103 102 101 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73
4
(001-13C) RST_ RA68 1 2 3 4
8 7 6 5
1 2 3 4
GND1 PD0 PD1 PD2 PD3 PD4 VDD1 GND2 PD5 PD6 PD7 PD8 PD9 VDD2 GND3 PD10 PD11 PD12 PD13 PD14 VDD3 GND4 PD15 PD16 PD17 PD18 PD19 VDD4 GND5 PD20 PD21 PD22 PD23 PD24 VDD5 GND6
(002-15F)
A (31:0)
109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144
CDRQ GND17 VDD16 CD31 CD30 CD29 CD28 GND16 VDD15 CD27 CD26 CD25 CD24 CD23 GND15 VDD14 CD22 CD21 CD20 CD19 CD18 GND14 VDD13 CD17 CD16 CD15 CD14 CD13 GND13 VDD12 CD12 CD11 CD10 CD9 CD8 GND12
8 7 6 5
CDAK CDRD CDWR INTR VDD17 GND18 HD0 HD1 HD2 HD3 HD4 VDD18 GND19 HD5 HD6 HD7 TEST0 TEST1 VDD19 GND20 MCLK VDD20 GND21 RESET HRD HWR HCS VDD21 GND22 HA0 HA1 HA2 HA3 TOUT1 TOUT2 VDD22
U25
VDD11 CD7 CD6 CD5 CD4 GND11 VDD10 CD3 CD2 CD1 CD0 GND10 VDD9 RXCKD RVID SVID PXCK PTIM PRDY GND9 VDD8 PDWR PDRD PDAK PDRQ GND8 VDD7 PD31 PD30 PD29 GND7 VDD6 PD28 PD27 PD26 PD25
72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37
8 7 6 5
RA103 1 2 3 4
27 26 25 24
23 22 21 20
8 7 6 5
RA101 1 2 3 4
23 22 21 20
19 18 17 16
8 7 6 5
RA98 1 2 3 4
19 18 17 16
8 7 6 5
RA104 1 2 3 4
15 14 13 12
11 10 9 8
8 7 6 5
RA102 1 11 2 10 3 9 4 8
VPL5
7 6 5 4
8 7 6 5
RA100 1 2 3 4
7 6 5 4
3 2 1 0
8 7 6 5
RA99 1 2 3 4
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36
3 2 1 0
L75
L76
L77
L70
10 11 12 13 14
15 16 17 18 19
20 21 22 23 24
C71
C77
C78
(007-16B) (009:01H)
QDD (31:0)
6
VPL5 L80 R75
C66
0 1 2 3 4
5 6 7 8 9
C76
1 2
DE GND X4
VCC OUT
R82
GPL5
$001
CPUD SIMMD
$002
3-7-28
2AD
(003-15A)
(008-09A)
178 Q2CDRQ
R88
2
108 107 106 105 104 103 102 101 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73
1 2 3 4
31 30 29 28
1 2 3 4
8 7 6 5
31 30 29 28
RA82 1 2 3 4 R86
8 7 6 5
$001
CPUD (15:0)
0 1 2 3 4 5 6 7
4
(011-13C)
RST_
170 Q2HWR_ 169 Q2HRD_ 168 Q2HCS_ RA81 1 2 3 4 8 7 6 5
1 2 3 4
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36
GND1 PDO PD1 PD2 PD3 PD4 VDD1 GND2 PD5 PD6 PD7 PD8 PD9 VDD2 GND3 PD10 PD11 PD12 PD13 PD14 VDD3 GND4 PD15 PD16 PD17 PD18 PD19 VDD4 GND5 PD20 PD21 PD22 PD23 PD24 VDD5 GND6
(002-15F)
A (31:0)
109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144
CDAK CDRD CDWR INTR VDD17 GND18 HD0 HD1 HD2 HD3 HD4 VDD18 GND19 HD5 HD6 HD7 TEST0 TEST1 VDD19 GND20 MCLK VDD20 GND21 RESET HRD HWR HCS VDD21 GND22 HA0 HA1 HA2 HA3 TOUT1 TOUT2 VDD22
U26
VDD11 CD7 CD6 CD5 CD4 GND11 VDD10 CD3 CD2 CD1 CD0 GND10 VDD9 PXCKD RVID SVID PXCK PTIM PRDY GND9 VDD8 PDWR PDRD PDAK PDRQ GND8 VDD7 PD31 PD30 PD29 GND7 VDD6 PD28 PD27 PD26 PD25
72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37
7 6 5 4 3 2 1 0
R87 R85 R83 RA67 1 2 3 4
27 26 25 24
1 2 3 4
8 7 6 5
27 26 25 24 23 22 21 20
CDRQ GND17 VDD16 CD31 CD30 CD29 CD28 GND16 VDD15 CD27 CD26 CD25 CD24 CD23 GND15 VDD14 CD22 CD21 CD20 CD19 CD18 GND14 VDD13 CD17 CD16 CD15 CD14 CD13 GND13 VDD12 CD12 CD11 CD10 CD9 CD8 GND12
23 22 21 20
VPL5
1 2 3 4
8 7 6 5
19 18 17 16
1 2 3 4
8 7 6 5
19 18 17 16
8 7 6 5 R81
15 14 13 12
1 2 3 4
8 7 6 5
15 14 13 12
31 30 29 28 27 26 25
11 10 9 8
1 2 3 4
8 11 7 10 6 9 5 8
VPL5
7 6 5 4
1 2 3 4
8 7 6 5
7 6 5 4
3 2 1 0
1 2 3 4
8 7 6 5
3 2 1 0
L78
L83
L81
L79
10 11 12 13 14
15 16 17 18 19
20 21 22 23 24
C83
C93
C92
QDD (31:0)
R84
C84
0 1 2 3 4
5 6 7 8 9
C89
$001 CPUD
3-7-29
2AD
1
C70 R73 SIMMD (31:0) RA97 1 31 2 30 3 29 4 28 RA95 1 27 2 26 3 25 4 24 RA92 1 23 2 22 3 21 4 20 RA90 1 19 2 18 3 17 4 16 RA96 1 15 2 14 3 13 4 12 RA94 1 11 2 10 3 9 4 8 RA93 1 2 3 4 RA91 1 2 3 4 7 6 5 4 3 2 1 0 15 14 13 12 11 10 9 8 BSD (31:0) 19 1 31 30 29 28 27 26 25 24 2 3 4 5 6 7 8 9 10 U24
_OE T_R A0 A1 A2 A3 A4 A5 A6 A7 GND Vcc B0 B1 B2 B3 B4 B5 B6 B7
$001
8 7 6 5 8 7 6 5 8 7 6 5 8 7 6 5 8 7 6 5 8 7 6 5 8 7 6 5 8 7 6 5 RA56 1 2 3 4
L71 C72
20 18 17 16 15 14 13 12 11 7 6 5 4 3 2 1 0
L73 C74
19 1 2 3 4 5 6 7 8 9 10
20 18 17 16 15 14 13 12 11 15 14 13 12 11 10 9 8
8 7 6 5
L72 C73
20 18 17 16 15 14 13 12 11 7 6 5 4 3 2 1 0
B0 B1 B2 B3 B4 B5 B6 B7
3-7-30
2AD
1
VPL5 R6 VPL5 R28 4 U6
D _PRE
RST_ 74 R14 1 2 3 4
CT RES_ VSC VS OUTC VSB-RI_ VCC GND
(003-15A)
2
2
3 S1
R25
3 1
CLK _CLR _Q
CT3 6
RST_
$001
U3 R16 R23
GPL5
GPL5
1 R29 1 U5 4 GPL5
(001-13F)
iRESET_
3
VCC3 L49 VPL5 L51 MCP 2AC (304:1) 46 R51 RCKEN 1 2
DE GND VCC OUT
VCC3
(003-15A)
4
MCP 2AC (304:1) (003-15A)
X2
iRCK2
(001-13D)
R40
GPL5
5
VCC3 L48 R30 VPL5 L50 10
DE GND VCC OUT _PRE
VPL5
U6
Q
1 2
12 11
9 8
L46
CPUCLK
(002-02C)
CLK _CLR _Q
X1
GPL5
$001 RST_
3-7-31
2AD
VCC3
VPL5
VPL5
VPL5
VPL5
VCC3
VCC3
L42
L41
L43
L44
L40
L45
2
20 VCC C26
20 VCC
5 VCC
5 VCC C24
20 VCC
C19
C17
C40
C15
C20
C16
R33
R32
R37
R34
C18 R35
3
GPL5
7 GND U6 GPL5
10 GND U8 GPL5
3 GND U5 GPL5
10 GND U7 GPL5
10 GND U10
4
VPL5 B2P-VH 1 CN2 E 5.1 V U2 L2 C1 3 VIN VOUT 2 GND 1 C4
+
4
VCC3 VPL5
C3
CE1
CT1
CT2
CE2
R2
G (5 V)
2 CN2
L1
R4
C94
C2
C5
GPL5
GPL5
6
GND1 GND2 GND3 GND4
GPL5
FG1 GMI5
GPL5
FG3 GMI5
R90
R3
GPL5
FG2 GMI5
GPL5
FG4 GMI5
3-7-32
2AD 2AD-1 E F G
L52 IC11
L31
IC6
IC6 S TR3 2B 5 S G
C59
1 S G
SC TIM
1 S G
IC30
L43
R169
SCNACK
CN8-18
L20
6 1C 1E
1B 2
L29
6 1C 1E
1B 2
PF7 PF6 PF5 PF4 PF3 PF2 PF1 PF0 Vdd GND PD7 PD6 PD5 PD4 PD3 PD2
TXD SCN
CN8-8
6 1C 1E
1B 2
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65
1 S G
4 2E 3 2C
2
CN4-2 SM Vref
1 S G
1 S G
IC18
L109
S A(8:0)
C85
IC18
C84
R223
S G _RESET IC20 A9 A10 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 S 1 A 2 B 3 C 6 4 G1 5 _G2A _G2B _Y0 _Y1 _Y2 _Y3 _Y4 _Y5 _Y6 _Y7 R224
_RD _WR
4
CN2-6
25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
DFTSW S R40 R39 L76 IC20 EFSSOL CN1-7 L51 IC20 CN1-8 L50 L49 IC20
CN2-12
L70 C73 S G
SBFSSOL
CN1-9 S R24 IC20 R23 IC20 S L107 C81 R111 X1 R77 S 4 2E 3 2C L37 S G TR6 2B 5 S G S G C79 CLK FLM
OFSOL1
CN1-11
L47 R78
C80
OFSOL2
CN1-10
L48
A23 A22 A21 A20 A19 A18 A17 A16 A15 A14 A13 A12 A11 A10 A09 A08 A07 A06 A05 A04 A03 A02 A01 A00 _RE
P53 P60 P61 P62 P63 P64 P65 P66 P67 P70 P71 P72 P73 P74 P75 P76 P77 SYSCLK VDD _XI XO VDD _OSCI OSCO VSS
IC22
VDD VSS _CS3 _CS2 _CS1 _CS0 _RAS D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 _WEH _WEL
S G
MIPCS_ SHDCS_
_CS PB7 PB6 PB5 PB4 PB3 PB2 PB1 GND Vdd PB0 PA0 PA1 PA2 PA3 PA4
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
MODE _RESET SELECT AD0 AD1 AD2 AD3 AD4 AD5 AD6 AD7 GND A0 A1 A2 A3 A4 A5 A6 A7 ALE _RD _WR CS
IC21
PD1 PD0 _Y3 PE7 PE6 PE5 PE4 PE3 PE2 PE1 PE0 GND PC7 PC6 PC5 PC4 PC3 PC2 PC1 PC0 INITD PA7 PA6 PA5
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41
+
R160 R161
IC30
S G
S G
L62
3
CN3-8 OCM Vref
S G
S L111 IC29 C89 C90 4 6 5 27 3 22 19 10 9 28 29 30 1 20 21 L142 C147 C148 R209 S 2 NC T C1 END REM INS _RES D3 26 D2 25 D1 24 D0 23
R214 S G
ODSW
CN4-1
L44 S
R33 R32
DFSSW1
CN2-10
L72 S
R35 R34 S
NO MOUNT DFSSW2 _WR R151 _WR OSSW CN2-4 L78 S S R44 CN2-9 L73
Vss 18 OSC2 16 DATA8 OSC1 15 DATA7 DATA6 SI TEST 17 DATA5 DATA4 VO4 14 DATA3 VO3 13 DATA2 VO2 12 DATA1 VO1 11 Vin 8 Vcc LED 7
R214 C149
S G
R213 S G R43 LED1/2 LED3/4 LED5/6 LED7/8 R30 Vin1/2 Vin3/4 Vin5/6 Vin7/8 R41 Vout1/2 Vout3/4 R10 S Vout5/6 CN8-10 L27 C2 S G SCAN START L151 S G Vout7/8 CN7-A1 CN7-A6 CN7-B6 CN7-B1 CN7-A3 CN7-A8 CN7-B8 CN7-B3 CN7-A5 L146 CN7-A10 L152 CN7-B10 L153 CN7-B5 CN7-A4 CN7-A9 CN7-B4 CN7-B9 G(5 V) G(5 V) G(5 V) G(5 V) L148
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
S G
SM ENABLE
CN4-11
R210 L150
6 1C 1E
1B 2
OSLSW
CN2-11
L71 S
6
R208 R207 R211 R212
R152
IC7
1 S G
A9 A10
R42
L147
L27
L77
L40 SM M3 CN4-5
R102
R11
L41 SM M2 CN4-4
IC7 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 S R205 12 11 10 9 8 7 6 5 27 26 23 25 4 28 29 3 2 R150 30 31 R149 IC13 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 D0 D1 D2 D3 D4 D5 D6 D7 _CE _OE 13 14 15 17 18 19 20 21 RA32 D0 D1 D2 D3 D4 D5 D6 D7 IC12
SC START
L149
L42 SM M1 CN4-3
IC7
IC12
5V 5V 5V 5V
IC7 S
IC12
IC7
4 2E 3 2C
TR7 2B 5
22 RA31 24 S G L141
IC12 S S 4 TR10 2E 2C 3
OFM ENABLE
6 1C 1E
1B 2
C145 C146 R204 2 1B 1C 6 1E 1 S G CLK FLM IC13 CN3-5 L65 CN3-4 OCM ENABLE OCM RET 5 2B
OFM CWB
CN3-3 L67
1 S G
IC28 R206 S G
OFM RET
CN3-1 L69
3-7-33
2AD 2AD-1
R166 R160
1 2 3 4 C139
R165
VF8
R188 8 R177
C105 C137 C103 C102 C136 A G R195 R191 R193 R189 R194 R187 C101 R126
S
VREF
R190
R192 A G
R163 A G
IC24
2
R220 VO_E+ VO_E CN6-5 CN6-4 R221 R175
2
A
3.3A
R176
VF8
VREF
L128
L118
L117
IC23 3.3D
S
R120
3 4
3.3D C142
R133 C117
C141
C119
C118
L101
L89
L92
L102
R62 C39
R58 C34
R92 C62
R83 C61
R196
R137
C100
R121
NC GND 1 7
R136
AG C111 C106
L114
C110
14 8 X2 3.3VOUT
C116
C95
C96
C94
R135
C107
C109
SG
SG
SG
SG
C104
C99
R130
R182
R184
AGSG
C63
C33
L100
1 2 3 4 5 6 7 8 9 10 11 12
SG
L2 D0 D1 D2 D3 D4 D5 D6 D7 WR RD AIN1
L99 RA1
C98
REFHO7 REFHO6 REFHO5 REFHO4 REFHO3 VSS REFHO2 REFHO1 REFHO0 REFLE7 REFLE6 VDD3 V REFLE5 REFLE4 REFLE3 REFLE2 VSS REFLE1 REFLE0 REFLO7 REFLO6 VDD5 V REFLO5 REFLO4 REFLO3 REFLO2 INCLK VSS STOP2 STOP1 AVDD2 AVSS2 AVDD1 AVSS1 REFLO1 REFLO0 MPX CLP3 VSS CLP2 CLP1 SHDE2 SHDE1 SHP0
132 131 130 129 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 104 103 102 101 100 99 98 97 96 95 94 93 92 91 90 89
R129
R128 RA2
L129
4
SHIFT+ SHIFT CLK+ CLK RS+ RS CLP+ CLP
CN5-5 CN5-4 CN5-11 CN5-10 CN5-9 CN5-8 CN5-7 CN5-6 L134 L133 L140 L139 L138 L137 L136 L135 2 3 6 5 10 11 14 13
IC25
DO1+ EN 12 DO1 EN 1 DO2+ DI1 7 DO2 DI2 9 DO3+ DI3 15 DO3 DI4 16 DO4+ VCC 8 DO4 GND
S G
RA42
C155
C144
C143 R198
+12 V
G(Analog) G(Analog)
C21
C158
AG
SG
NO MOUNT R79
AG
RA4
IC15 10 9 8 7 6 5 4 3 20 21 24 2 SG D7 D6 D5 D4 D3 D2 D1 D0 AVSS AVSS DVSS DVSS CLK VRT VRB VIN VRTS VRBS AVDD AVDD AVDD DVDD DVDD _OE 12 17 23 19 16 22 14 15 18 11 13 1
SG
A0 A1 A2 A3 A4 VSS A5 A6 A7 A8 _SHDCS VDD3 V _IOWR _IORD D0 D1 VSS D2 D3 TPD D4 D5 VDD 5 V D6 D7 XTST _RESET VSS XTCK0 XTCK1 XSM MST VDD3 V MMS0 MMS1 SMCK TEST0 TEST1 VSS TEST2 TEST3 TEST4 TEST5 TEST6
R50 C14
C16
133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176
REFHE0 REFHE1 REFHE2 REFHE3 REFHE4 VSS VDD3 V REFHE5 REFHE6 REFHE7 SHIFT VDD5 V CCDCLK1 CCDCLK2 CCDCLK1 CCDCLK2 VSS _BCLAMP RS1 RS2 OVSS CLAMP1 CLAMP2 OVDDS SPHOLD1 SPHOLD2 _PCLK VSS PCLK DVSS SVSYNC _SVSYNC VDD5 V SHDOUT0 SHDOUT1 SHDOUT2 SHDOUT3 VDD3 V VSS SHDOUT4 SHDOUT5 SHDOUT6 SHDOUT7 MRE
IC17
SHPE SHD0 CXADT7 CXADT6 CXADT5 VSS VDD3 V CXADT4 CXADT3 CXADT2 CXADT1 VDD5 V CXADT0 CXAL2 CXAL1 CXAL0 VSS CXARD _CXAWR EVEN7 EVEN6 EVEN5 EVEN4 EVEN3 EVEN2 EVEN1 EVEN0 VSS ADCCLK2 ADCCLK1 ODDM7 ODDM6 VDD5 V ODDM5 ODDM4 ODDM3 ODDM2 VDD3 V VSS ODDM1 ODDM0 _PHSYNC PVSYNC TEST7
88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45
RA18 RA19
R127
C93
SG
37 38 39 40 41 42 43 44 45 46 47 48
T1 AVCC CLP1 SHPE SHDE1 SHDE2 MPX SHPO SHDO CLP2 CLP3 PCND
R134
IC16
ODDOUT AGND MPXOUT VRT VRB CLPOC1 CLPEC1 TDA AIN5 AIN4 AIN3 AIN2
AG
C153
L82
NO MOUNT MIPIN4 MIPIN5 MIPIN6 MIPIN7 RA6 NO MOUNT C114 MIPIN(7:0) MREIN _RESET A(8:0) R65 SHDCS_ _WR R88
S
L115
L116
3.3D
SG
R131
C115
R132
A0 A1 A2 A3 A4
S G
S G
A5 A6 A7 A8
SG
R66 D0 D1
D2 D3
D4 D5
_RD D(7:0)
D6 D7
R81
L119
3.3D
S
C30
R84
AG
C26
RA3
R54 C24
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44
NO MOUNT
AG
3-7-34
2AD 2AD-1
RA20
IO27 IO26 IO25 IO24 IO23 IO22 IO21 IO20 RA27 R145
S 3.3D
SA213 C38 3.3D R61 S G C37 MIPOUT0 SID 0 SID 0+ SID 1+ SID 1 CN8-31 CN8-33 CN8-29 CN8-27 L2 L1 L3 L4 MIPOUT1 1 2 3 4 5 6 7 8 S G IC3 A1 Y1 Z1 G Z2 Y2 A2 GND VCC A4 Y4 Z4 _G Z3 Y3 A3 16 15 14 13 12 11 10 9 L91 S MIPOUT3 L125 SA212 SA211 SA210 SA29 SA28 SA27 SA26 SA25 SA24 SA23 SA22 SA21 SA20
R147 R203
IS213 IS212 IS211 IS210 IS29 IS28 IS27 IS26 IS25 IS24 IS23 IS22 IS21 IS20
RA30
C128 R97
S G
R148 R98
IC27 RAMEN_
SID 2 SID 2+
CN8-23 CN8-25
L9 L7
RA29
11 12 13 15 16 17 18 19
L123
22 20 27 IS20 10 IS21 9 IS22 8 IS23 7 IS24 6 IS25 5 IS26 4 IS27 3 IS28 25 IS29 24 IS210 21 IS211 23 IS212 2 IS213 26 1 S G
Vcc
28 C127
GND
14 S G
R146
SD21 SD20
SA213
C129
SD10
MIPOUT2 3.3D
3.3D L103 SD17 SD16 SD15 SD14 SD13 SD12 SD11 SD10 RA20
RA22 IO17 IO16 IO15 IO14 IO13 IO12 IO11 IO10 S R141 IC26 IS113 IS112 IS111 IS110 IS19 IS18 IS17 IS16 IS15 IS14 IS13 IS12 IS11 IS10 IS10 IS11 IS12 IS13 IS14 IS15 IS16 IS17 IS18 IS19 IS110 IS111 IS112 IS113 S G 22 20 27 10 9 8 7 6 5 4 3 25 24 21 23 2 26 1 _OE _CE _WE A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 Vcc 28 C125 L122 C124 L121 R140 3.3D
C68
120 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 104 103 102 101 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81
CN8-21 CN8-19
C164
C66
VDD5V3 SD27 SD26 SD25 SD24 SD23 SD22 VSS18 SD21 SD20 WR2_ OE2_ SA213 VDD3V11 SA212 SA211 SA210 SA29 SA28 VSS17 VDD5V2 SA27 SA26 SA25 SA24 SA23 VSS16 SA22 SA21 SA20 SD17 SD16 VDD3V10 VSS15 SD15 SD14 VS13 VS12 VS11 VDD3V9
S G
R101 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160
C42
4
R63 S G MIPOUT4 SID 4 SID 4+ SID 5+ SID 5 CN8-15 CN8-17 CN8-13 CN8-11 L17 L15 L19 L22 MIPOUT5 1 2 3 4 5 6 7 8 S G A1 Y1 Z1 G Z2 Y2 A2 GND C37 VCC A4 Y4 Z4 _G Z3 Y3 A3 IC4 16 15 14 13 12 11 10 9 L93
SID 6 SID 6+
CN8-7 CN8-9
L26 L24
RA11
SID 7+ SID 7
CN8-5 CN8-3
L28 L30
SVSYNC IN
3.3D C46
6
R59 S G 1 2 3 4 5 6 7 8 S G SMRE + SMRE CN8-30 CN8-28 L8 L10
C36 3.3D
L96
SOVSYNC SOVSYNC +
CN8-32 CN8-34
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
L6 L5 R60
A1 Y1 Z1 G Z2 Y2 A2 GND IC2
VCC A4 Y4 Z4 _G Z3 Y3 A3
16 15 14 13 12 11 10 9
S G
R69
VDD5V1 A0 A1 A2 A3 A4 A5 A6 A7 A8 VSS1 VDD3V1 MIPCS_ IORD_ IOWR_ VSS2 RESET_ SCM TFSEL0 VDD3V2 VSS3 TFSEL1 TFSEL2 D0 D1 D2 VDD3V3 VSS4 D3 D4 D5 VDD3V4 VSS5 D6 D7 TEST0 TEST1 TEST2 SVSYNC VDD3V5
C35
C48
L90
VSS19 VSS20 PORT0 PORT1 PORT2 MRETHIN MREOUT MREMIP VDD3V12 MIPCLK VSS21 MIPOUT0 MIPOUT1 MIPOUT2 VDD3V13 MIPOUT3 MIPOUT4 MIPOUT5 VSS22 VDD3V14 MIPOUT6 MIPOUT7 FVSYNC FHTHIN_ FHSYNC VSS23 VDD3V15 TESTD0 TESTD1 TESTD2 TESTD3 VSS24 VDD3V16 TESTD4 TESTD5 TESTD6 TESTD7 MRED VSS25 VSS26
IC5
VSS14 VSS13 SD10 MR1_ OE1_ SA113 SA112 VSS12 SA111 SA110 SA19 SA18 SA17 SA16 VDD3V8 VSS11 SA15 SA14 SA13 SA12 SA11 SA10 VDD3V7 VSS10 INCLK VSS9 MIPIN7 MIPIN6 MIPIN5 MIPIN4 MIPIN3 VSS8 VDD3V6 MIPIN2 MIPIN1 MIPIN0 MREIN SHSYNC_ VSS7 VSS6
RA10 R202
R142
RA9
RA21
RA8
RA23
C50
L95
C160
C161
C162
C69
MIPOUT6
5
CLKIN MIPIN(7:0)
6
MREIN SHSYNCIN
C45
SVSYNCIN S G
C47
C49
S G
S G
S G
S G
7
3.3D
R68
S G
A(8:0) G (5 V) G (5 V) G (5 V) CN8-2 CN8-6 CN8-22 L33 L32 L16 S G C44 MIPCS_ _RD D0 D1 D2 D3 D4 D5 _RESET D(7:0) D6 D7 _WR S G R64
A0 A1 A2 A3 A4 A5 A6 A7 A8
CN8-24 CN8-26
L14 L12
L94
3-7-35
E A E
E A E
2AD-1 2AD
2
L86 C27 C28 E 5.1 V CN9-1 E 5.1 V CN9-2 S A S C22 C25 C23 S S S S L106 S L110 S NO MOUNT L66 L58 L53 L45 L98
2
+
R55 C165 C166
C56
C76
C9
C7
C5
C10
C3
C57
C77
C8
C6
C4
S G
A G S G
C88
L85
C87
R56
3
+12 V
CN9-5 C167
R109
R52 C17
C18
+
C15 C13 C20 S G C132 R171 C151 R222 C150 R217 C12 R49 C1 R1 S G S G S G S G S G S G S G
C168
G(ANALOG) CN9-6
L81
R51
A G FG FG FG FG FG L105
S L126 L127
R114
R27
R26
R25
R22
R74
L84
L97
4
C198 C140
C134
C71
C53
C133
C70
C51
R103
R174
VIN
VOUT
C170
C169
R225
C32
ADJ
C31
D1
S G
S G
R71
IC1
A G
A G
R181
3.3D
3.3A
S G
C131
FET1 D G S
S G
R226
R228
A G
R227
C156
7
A G
3-7-36 3-7-18
E A E A E A Point Source Ai5050 (MCA) E A A E
E A E
E A E
2AD
C20
2
7 VDD
C19 S G 6 A 5 _A 2 B 1 _B R17 TPI NO MOUNT CN2-4 CN2-6 CN2-3 CN2-1 SM A SM A_ SM B SM B_ L3 SHPSW CN4-2 C1 S G L4 ODSW CN5-2 C21 CN2-5 CN2-2 24V 24V + C3 S G CN1-14 ODSW S G CN1-2 SHPSW
8 9 10 11 12 13 14 15 16 17 18
4
R1 SM RET CN1-5
S R12
S G
4
DT2 EL ON REM CN1-3 B E C
DT1 B E S G C
S S
L5
SM ENABLE CN1-4
CN3-1 CN3-2
EL EL
5
L1 C4 C5 C2 E 5.1 V CN6-4
P G CN4-1 CN5-1 5V 5V
C10
C11
R11
L2
G (5 V)
CN6-3
R10
S G
S G
6
JP14 F G JP3 JP1 JP4 JP2 F G
24 V 24 V
R13
F G
G(24 V)
CN6-1
P G
3-7-37 3-7-19
E A E A A E Point Source Ai5050 (MCA) E A A E
E A E
E A E
2AD-1 2AD
CCD PCB
A B C D
F4
E
R17 R13 R16 R15
14 13 11 12 16 1 9 15 10
IC1
F5
VDD VDD VDD VDD CP1_EVEN CP1_ODD CP2_EVEN CP2_ODD CP_LH_EVEN CP_LH_ODD VGG CP_RS_EVEN CP_RS_ODD CP_CLP_EVEN CP_CLP_ODD CP_ROC VOUT_EVEN NC VOUT_ODD NC NC NC GND NC GND NC GND NC
F1
18 10 20 9 26 3 27 2 28 1 12 7 8 13 14 15 21 22
IC2
CK_out _CK_out CK_out _CK_out 2B_out _2B_out RS_out CP_out SH_out CK_in
IC3
6
1
2 1 6 7 10 9 14 15
F3 F2
C3
2B_in
C1
A G
R5 R7
C14
A G
A G
F8
4 12 3 5 11 13 16 8
CN1-1 CN1-2 CN1-3 CN1-4 CN1-5 CN1-6 CN1-7 CN1-8 CN1-9 CN1-10 CN1-11
C7
C4
R8
C5
C15
R14
R24
F15 F16
R6
A G
C17 C16 C18
F17 F18
A G
A G
R12
A G
R3
TR1
+ A G
C1
4
R2 R32
R29
IC5
FBP VIN VREF FBN
4
8 5
A G
RA1
C6
1 2 3 4
R33 R34
CN2-1 CN2-2
VO_O+ VO_O
R31
R1
TR2
C10 A GA G C8 R25
R35 R36
CN2-3 CN2-4
VO_E+ VO_E
A G
R9 R28
IC4 1 2 3 4
FBP VIN VREF FBN
A G
8 5
6
C23 C9 R27
CN2-5 CN2-6
F19
CN2-7
A G
R37
7
F6
C11
C13
C22
C21
C20
IC5
IC4
C19
R30
R26
IC2
R4
C12
4,5
A G
A G
A G
3-7-38 3-7-20
E A E A E A Point Source Ai5050 (MCA) E A A E
E A E
E A E
2AD
CCD PCB
A B C D E F G H I J
IC1
F1 C7 C4
C12
A G
A G
R21
CP1_EVEN CP1_ODD CP2_EVEN CP2_ODD CP_LH_EVEN CP_LH_ODD VGG CP_RS_EVEN CP_RS_ODD CP_CLP_EVEN CP_CLP_ODD CP_ROC VOUT_EVEN NC VOUT_ODD NC NC NC GND NC GND NC GND NC
18 10 20 9 26 3 27 2 28 1 12 7 8 13 14 15 21 22
IC3
14 13 11 12 16 1 9 15 10
CK_out _CK_out CK_out _CK_out 2B_out _2B_out RS_out CP_out SH_out CK_in
IC2
6 R20 R18 R23 R22 R19 4 12 3 5 11 13 16 8
EN EN DO1 DO2 DO3 DO4 VCC GND DI1+ DI1 DI2+ DI2 DI3+ DI3 DI4+ DI4
C6
2B_in
2 8
C1
F4
2 1 6 7 10 9 14 15
CN1-1 CN1-2 CN1-3 CN1-4 CN1-5 CN1-6 CN1-7 CN1-8 CN1-9 CN1-10 CN1-11
R15
R4 R3 R13 R12
C13
R27
F12 F13
A G
A G
R6 R5 R11
A G
C15 C16
F20
F21
3
R40 R1 TR1
A G
+ A G
C10
R32
R16 R35
A G
RA1 R41
C5
1 2 3 4
IC5
FBP VIN VREF FBN
4
R36 R37
8 5
CN2-1 CN2-2
VO_O+ VO_O
R34 R2 TR2
C11 A GA G C8 R28
R38 R39
CN2-3 CN2-4
VO_E+ VO_E
A G
R17 R30
IC4 1 2 3 4
FBP VIN VREF FBN
A G
8 5
6
C21 C9 R31
F17
6
CN2-5 CN2-6 CN2-7 +12V G(Analog) G(Analog)
F19 F18
A G
7
R43 R42 0 6 0 6 F14
7
4,5 C3
C20
C19
C18
C17
IC5
IC4
IC3
R33
R29
R14
C14
C2
A G
A G
A G
3-7-38 3-7-20
E A E A E A Point Source Ai5050 (MCA) E A A E
E A E
E A E
2AD
DF driver PCB
A
S S OSSW CN6-B2 1 1B S G S OFSW CN6-B5 S G S S OSBSW CN6-A5 1 1B S G S OFTSW CN6-A14 S G S S OFSOL 1 OSLSW CN6-A11 S G B E S G CN5-B13 OFSOL2 CN2-16 OFSOL2 C CN3-5 OSLSW CN2-15 2 E 1C 5 S 2C 4 CN3-3 OSBSW SBPSOL1 CN2-21 S CN3-4 DFTSW SBPSOL2 CN2-22 P G CN5-B12 OFSOL1 1 1B 2 E 2C 4 1C 5 P G CN5-A3 SBPSOL2 CN5-A2 SBPSOL1 OFCL CN2-20 2 E 1C 5 S 2C 4 CN3-1 OSSW SBFSSOL CN2-17 CN5-B8 SBFSSOL
E
S
H
S
I
S
*
EFSSOL CN2-19 CN5-A7 EFSSOL
S G 3 2B
CN3-2
OFSW
COM P G
14
*
CN5-A5 OFCL
7 S G
4 S G
S G 3 2B
3 2B
3
OSLEDPCB (GN) CN3-9 1 1B S 2 E
* *
DFSSW2 CN4-3
S G
P G
S G
CN6-B9 1C 5
OSLEDPCB (GN)
P G
4
OSWSW CN6-A8 CN3-8 OSWSW DFSSW1 CN4-4
P G S S G
3 2B
P G S G S G S G OCM Vref 24 V 24 V CN1-1 CN1-2 + PG PG CN1-3 CN1-4 CN4-2 24 V(VEN) OCM M1 OCM M2 OCM M3 CN2-6 CN2-1 CN2-2 CN2-3 CN2-4 CN2-5 CN2-8 CN2-7 S
S S G
*
F G
*
F G
*
F G
*
F G
5
* * * *
VIN +
VOUT ADJ
N.C. N.C.
S G
S G
S G
P G N.C. N.C.
N.C. N.C.
CN1-5 CN1-6
+ S G
6
5V 5V CN1-7 CN1-8 +
S G
*
OCM RET CN2-9 S
CN5-A9 CN5-A8
* Not installed
6
P G
CN2-10
B E
S G S G S OFM CLK OFM RET OFM CWB 24 V 24 V 24 V 24 V 24 V 24 V OFM ENABLE CN2-14 CN2-12 CN2-13 CN2-11
CN6-A9 CN6-A12 CN6-A15 CN6-B1 CN6-B4 CN6-A6 CN6-B10 CN6-B13 CN6-B8 CN6-A7 CN6-A10 CN6-A13 CN6-B3 CN6-B6 CN6-A4 CN6-B12 CN6-B15
5V 5V 5V 5V 5V 5V 5V 5V SG SG SG SG SG SG SG SG SG
24 (VEN)
CN4-1
+ S G S
5 4 3 2
R
7
CN5-B3 CN5-B5 CN5-B4 CN5-B6 S G CN5-B1 CN5-B2 OFM ACOM 24 V (VEN) OFM BCOM 24 V (VEN) + OFM A OFM A OFM B OFM B
Vref
11 SP 1 GND
B E S G
C P G
8
S G
8
S G
DF SHORT
CN3-11
S G
3-7-39 3-7-21
E A E A A E Point Source Ai5050 (MCA) E A A E
2AD G H I J
C B C E C46 S G S G
S G
10 5 IC13
6 IC13
S G 2
IC15
R143
2
C18 R63 D0 D1 D2 D3 D4 D5 D6 D7
S R168 IC9
S G
N.C
CN6-1
S G
AN1 P72 100 P73 99 P74 98 P75 97 P76 96 P77 95 Vss 94 AVss 93 Vref 92 AVcc 91 Vcc 90 P80/CTS0 89 P81 88 R120 P82/RD0 87 P83/TD0 86 R119 P84/_INT4 85 R118 P85 84 RD1 83 R117 TD1 82 81
S G
L11 CN6-7 CN6-2 CN6-8 CN6-11 TXD MMI G (5 V) G (5 V) G (5 V) IC14 D0 D1 D2 D3 D4 D5 D6 D7 13 14 15 17 18 19 20 21 D0 D1 D2 D3 D4 D5 D6 D7 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 12 11 10 9 8 7 6 5 27 26 23 25 4 28 29 3 2 30 31 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 D0 D1 D2 D3 D4 D5 D6 D7 13 14 15 17 18 19 20 21 D0 D1 D2 D3 D4 D5 D6 D7
R157 C51
C50
R15
C17
C B C E C48 S G S G
S G
S G
22 20 27 10 9 8 7 6 5 4 3 25 24 21 23 2 26 1
Vcc 28 _OE _CE _WE A0 GND 14 A1 S G A2 I/O0 11 A3 I/O1 12 A4 I/O2 13 A5 I/O3 15 A6 I/O4 16 A7 I/O5 17 A8 I/O6 18 A9 I/O7 19 A10 A11 A12 A13 A14
R145
_HOLD
BYTE CNVss _RESET Xin Xout _RD Vss Vcc _HLDA ALE _BHE _WR P117 P116 P115 P114 P113 P112
AN0 P95/_INT3 P94 A22 A21 A20 P90 P67/TB2in P66/TB1in P65/TB0in P64/_INT2 P63/_INT1 P62/_INT0 P61/TA4in P60/TA4out P57/TA3in P56/TA3out P55/TA2in P54/TA2out P53/TA1in P52/TA1out P51/TA0in P50/TA0out P47 P46 P45 P44 P43 I _RDY
IC19 IC19
A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 A23 D0 D1 D2 D3 D4 D5 D6 D7 P110 P111
S R56 R57 R58 R94 R95 R96 R97 R98 R91 R90 R52 R89 R99 R92 R93 R100 R114 R101 R102
IC12 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 12 11 10 9 8 7 6 5 27 26 23 25 4 28 29 3 2 30 31 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18
IC16 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 12 11 10 9 8 7 6 5 27 26 23 25 4 28 29 3 2 30 31 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 D0 D1 D2 D3 D4 D5 D6 D7 13 14 15 17 18 19 20 21 D0 D1 D2 D3 D4 D5 D6 D7
RA1
RA3
RA4
S 22 R45 _CE 24 _ROM1 _OE _RD L35 1 Vpp 32 Vcc 16 GND S C31
S 22 R45 _CE 24 _ROM2 _OE _RD L36 1 Vpp 32 Vcc 16 GND S C33
S 22 R59 _CE 24 _ROM3 _OE _RD L39 1 Vpp 32 Vcc 16 GND S C39 R116
RA5
C30
C32
R110
RA6
R112
C38
S G
S G
S G
RA7
A_BUS
R160 31 32 33 R162 34 35 36 37 38 R167 L42 39 40 41 42 L41 43 44 R124 LED L4 45 LED L3 46 LED L2 47 LED L1 48 LED R4 49 LED R3 50 LED R2
LED R1
D_BUS 2 A15 A16 A17 A18 IC3 1 11 10 S R62 A19 A20 A21 R66 R65 IC3 R67 1 A0 2 A1 3 A2 6 4 5 E3 _E1 _E2 15 14 13 12 11 10 9 7 9 R28 R68 _ROM2 _ROM3 R29 R20 R32 1 12 11 IC4 13 10 8 R26 S 9 IC4 8 R61 _RDY 4 _E 5 IC2 6 R25 _VRAM 2 IC2 3 R27 _LCD 8 R33
VCC
3 R70
12 IC6 13 R72
9 IC6 8 10 R71
R164
R122
X1
R166
C41
C40
LED L3
S G
IC4
_WR
_WR
LED L2
LED L1
MPUCLK
LED R4 _E
LED R3
LED R2
3-7-40
E A E
E A E
2AD
G
10
S SG
S SG
1
9 S D_BUS 24 V L52 A_BUS VA3 VA2 VA1 VA0 D7 D6 D5 D4 D3 D2 D1 CN5-4
L17 C12
+
C11
C55
28 C54
Vcc
SG O0 O1 O2 O3 O4 O5 O6 O7 11 12 13 15 16 17 18 19
RA10
L21
VA4 VA5 VA6 VA7 VA8 VA9 VA10 VA11 VA12 VA13 VA14
RA9 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 VA4 VA5 VA6 VA7 VA8 VA9 VA10 VA11 VA12 VA13 VA14 VA15 _VCS4 _VCS3 _VCS2 _VCS1 _VCS0 VD0 VD1 VD2 VD3 VD4 VD5 VD6 VD7 VD8 VD9 VD10 Vdd Vss
VA3 VA2 VA1 VA0 __VME DB15 DB14 DB13 DB12 DB11 DB10 DB9 DB8 DB7 DB6 DB5 DB4 DB3 DB2 DB1
14
GND
22 20 27 10 9 8 7 6 5 4 3 25 24 21 23 2 26 1
SG VA0 VA1 VA2 VA3 VA4 VA5 VA6 VA7 VA8 VA9 VA10 VA11 VA12 VA13 VA14
RA8
R169
50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31
+
C14 SG
RA11
IC11
Vin
GND
R78
S L43
O0 O1 O2 O3 O4 O5 O6 O7 C42 R126
RA12
23 V
VLCD S R106
RA13
VD11 VD12 VD13 VD14 VD15 LCDENB XSCL LP WF YD UD0 UD1 UD2 UD3 LD0 LD1 LD2 LD3 OSC1 OSC2
C43 C29
R128 R134 LCD. REM CN1-14 R131 R137 XSCL CN1-10 R130 R136 LP CN1-11 R129 R135 DIN CN1-12 R133 R139 XD0 CN1-6 R132 R138 XD1 CN1-5 R172 R174 XD2 CN1-4 R171 R173 XD3 CN1-3 L46 G (5 V) CN1-8 SG NC CN1-13 3 IC17 11 IC17 6 IC17 11 IC17 8 IC17 6 IC17 3 IC17
S R109
SG L27 L23 L26 L16 L15 L44 L53 L28 L37 L38
R108
C27
81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100
SG
C28
R107
C45
C57
C24
C35
C8
R127
R170
R113
_LCD
R115
R23
R75
C37
DB0 AB15 AB14 AB13 AB12 AB11 AB10 AB9 AB8 AB7 AB6 AB5 AB4 AB3 AB2 AB1 AB0 _BHE MPUSEL RESET MPUCLK READY _MEMRD _MEMWR _MEMCS _IORD _IOWR _IOCS Vdd Vss
D0 A15 30 A14 29 A13 28 A12 27 A11 26 A10 25 A9 24 A8 23 A7 22 A6 21 A5 20 A4 19 A3 18 A2 17 A1 16 A0 15 14 S S G R103 S 13 R104 S 12 HRESET 11 MPUCLK 10 _READY 9 R105 8 7 6 5 4 3 2 S 1 Vdd
L19 G (5 V) CN5-2 S
3
9 8 Vin+ _Control IC8 Vset Filter Vout 1 2 3 C25 L22 CN2-2 CN2-1 24 V
+
C26
23 V
5
S
14
14
14
14
14
14
3-7-41 3-7-23
E A A E
E A E
E A E
2AD
N.C.
TB
KEY8 KEY9 DIG KEY_R1 DIG KEY_R2 DIG KEY_R3 DIG KEY_R4 CNB-1 CNB-2 CNB-3 CNB-4 KEY11 KEY10
KEY15
KEY19
KEY23
3
D4 SCAN_R1 SCAN_R2 CNB-5 CNB-6 CNB-7 CNB-8 D5 D6 D7
SCAN_R3 SCAN_R4
5
BZ1
R7
R8
5
TR4
6
BUZZER CNB-13
LED17
LED18
LED19
LED20
7
5V DIG LED_R1 DIG LED_R2 DIG LED_R3 CNB-14 CNB-9 CNB-10 CNB-11 CNB-12 R17 R18 R19 R20
DIG LED_R4
3-7-42 3-7-24
E A E A E A Point Source Ai5050 (MCA) E A A E
E A E
E A E
2AD
1
KEY1 DIG KEY_L1 DIG KEY_L2 DIG KEY_L3 CNA-5 CNA-6 CNA-7 KEY2 KEY3 KEY4 KEY5 KEY6 KEY7
2
SCAN_L1 SCAN_L2 SCAN_L3 CNA-8 CNA-9 CNA-10
D1
D2
D3
3
R1
R2
R3 TR1
R4
R5 TR2
R6
TR3
LED1
LED2
LED3
LED4
LED5
LED6
LED7
LED8
LED9
LED10
LED11
LED12
LED13
LED14
LED15
R13
LED16
5V N.C
CNA-16 CNA-18
R15
R14
5V
L1 B1 R28 C1 R29
4 3 2 1 5 T1
12
CNC-1
7 C2
CNC-4
R22
R30
7
TR6 R27
R25
R26
3-7-43 3-7-25
E A E A A E Point Source Ai5050 (MCA) E A A E
2AD
+5 V
1
1 2 R63 CN1-7 CN1-8 CN1-9 DLSW1 UPSW1 DLSW2 7 8 9 10 1 7 8 1 R33 2 1 R36 2 1 2 R62 1 2 R61 1 2 R60 1 R11 2 UPSW1 UPSW2 IC6.6 13 A Y 12 IC6.4 9A Y 8 IC6.5 11 A Y 10 DSW0 DSW1 PESENS WDT IC6.3 5A Y 6 2 1 4 3 Y A IC6.2 1 R35 2
+5 V
1 1 R65 R64 2 2 PDMSENS2 2 PDMSENS1 IC9.3 5A Y 6 1 B E 3 GROUND 1 2
1
C 2 Q13
Y A
+5 V +5V
1 R16 1 R20 2 2 C18 + 1 2 GROUND
+24 V
1 2 3 4 5 C16 + 1 2 AGROUND 12 N.C 1 +24 V 2 +24 V 6 CCL 5 4 PFCL2 PFCL1 +24 V PG CM PWM +5 V CM CLK CN12-1 CN12-2 CN12-3 CN12-4 CN12-5
IC6.1
R34
+5 V
1 R17 2
R37
+5 V
1 R3 2
C4
GROUND
GROUND CN1-11 PPSENS3 11 1 R42 2 IC9.4 9A Y 8 60 59 58 57 56 54 53 52 51 50 49 48 47 46 44 43 42 41 CN1-5 PESENS 5 1 R41 2 61 62 63 +5 V 64 65 66 67 68 69 70 71 GROUND 72 73 PFSW* 74 75 76 77 78 79 80 P74/ANI4 P73/ANI3 P72/ANI2 P71/ANI1 P70/ANI0 P17 P16 P15 P14 P13 P12 P11/PWM1 P10/PWM0 MODE ASTB P40/AD0 P41/AD1 P42/AD2 IC9.2 3A Y 4 IC9.1 1A Y 2 1 11 3 4 7 8 13 14 17 18 IC3 0C G 1D 1Q 2D 2Q 3D 3Q 4D 4Q 5D 5Q 6D 6Q 7D 7Q 8D 8Q
+24 V
IC2 2 5 6 9 12 15 16 19 20 22 10 9 8 7 6 5 4 3 25 24 21 23 2 26 27 CE OE A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 3 6 11 14 9 16 COM1 COM2 01 IN1 02 IN2 03 IN3 IN4 04 IC4 CN4-12 CN4-1 CN4-2 CN4-6 CN4-5 CN4-4
CN1-6
PPSENS2
R40
CN4-9
PPSENS1
R39
IC9.5 11 A Y 10 IC9.6 2 13 A Y 12
4
CN4-10 N.C CN1-1 LED CLK 10 1 R45 1 1 1 R48 2 R38 IC5.6 13 A Y 12 IC5.5 11 A Y 10 C 2 1 Q14 B E 3 1 R43 2 6 1 R15 2
+5 V
R53 R54 R59 R58 1 1 1 1 GROUND CN2-1 CN2-2 CN2-3 CN2-4 CN2-5 CN2-6 +5 V SG PLDSENS1 +5 V SG PLDSENS2 1 2 3 4 5 6 GROUND 1 2 3 4 5 2 2 2 2 1 R50 2 1 R51 2
Y A
IC5.3
P75/ANI5 P76/ANI6 P77/ANI7 AVdd AVref1 AVss ANO0 ANO1 AVref2 AVref3 P20/NMI P21/INTP0 P22/INTP1 P23/INTP2/CI P24/INTP3 P25/INTP4/ASCK P26/INTP5 P27/SI P30/RxD P31/TxD
IC7
+5 V
R28 DA2 3 1 R31 2 2 1 1 R32 2 PFSW* 1 2 3 DA1 2 1
P43/AD3 P44/AD4 P45/AD5 P46/AD6 P47/AD7 P50/A8 P51/A9 P52/A10 P53/A11 P54/A12 P55/A13 P56/A14 P57/A15 P60/A16 P61/A17 P62/A18 P63/A19 P64/RD P65/WR P66/WAIT
40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21
GROUND
O0 O1 O2 O3 O4 O5 O6 O7
11 12 13 15 16 17 18 19
2 7 10 15
N.C
+5 V
1 R22 N.C C6 1 2 N.C 3 N.C CN4-3 1 R21 2 2 2 N.C CN1-2
GROUND
+5 V
1 R10 2
+5 V
1
+24 V
1 R25 Q3 C 2 2 3 D4 B E 1 1 2 K A K 1 D1 A 2 SIG
R49
+24 V
+5 V R6 1
1 8 9 Y A B IC5.4 2
+5 V R7 1
2
+5 V
1 R24 2 3 B C 2 E 1
1 2 3 4 5 6 7 8 1 OSO1 2
10 12 13 14 15 16 17 18 19 20 3
Q1
+24 V
PDMSENS1 1 R26 2 Q2 C 2 3 D2 B E 1 1 2 K A K 1 D3 A 2 SIG PDMSENS2
+5 V
1 R4 2 12 13 UPSW1 2 1 2 A Y B IC8.1 3 4 5 A 11 10 9 C 2 A Y B IC8.3 A 8 1 B E 3 6 GROUND Q5
IC5.2 3A Y 4
CN7-1 CN7-2 CN7-3 CN7-4 CN7-5 CN7-6 CN7-7 CN7-8 CN7-9 CN7-10
AGROUND
6
GROUND
GROUND
GROUND
+5 V R8 1 GROUND
2 C 2 1 B E 3 GROUND FUSE1 1 2 Q9
+5 V
1 R52 2 1 R1 2
GROUND
+5 V
R5 1
B IC8.4
+5 V
R27
+5 V +5 V
R9 1 WDT 2 1 C1 1 R2 2 3 8 1 1 R23 2 6 CK RES CT VREF VS 7 1 2 C2 2 RES Vcc IC1 GND 4
CN1-4
DOSSW
2 K
ZD2 1 A
+5 V
5 1 2 C7
Y B IC8.2
1 B
1 C 2 2 3 04 B C 2 E 1 Q6
E 3 GROUND
AGROUND
CN4-11 SCSW
11
+5 V
1 2 C8 GROUND IC2 1 2 C9 IC3 1 2 C10 IC5 1 2 C13 IC8 1 2 C12 IC7 1 2 C11 IC6 1 2 C19 IC9 1 2 C5
+5 V + 1
CN3-1 CN3-2 CN3-3 CN3-4 +5 V SG +24 V PG 1 2 3 4 2 K 1 C15 ZD1 A 2
+24 V +5 V
C14
2 GROUND
+ 1
2
+ 1
K 1 D5 A 2 SIG 2
C17
GROUND
8
GROUND AGROUND
8
* Switch on the copier
3-7-44
Interface PCB
A B C D E F G H I J
2AD
+5 V
1
+5 V +24 V 1 R1 2 CN3-1 CN3-2 CN3-3 CN3-4 +5 V SG DLSW1 +5 V SG UPSW1 +5 V SG DLSW2 +5 V SG UPSW2 1 2 3 4 5 6 7 8 9 10 11 12 1 2 CN4-1 CN4-2 CN4-3 CN4-4 CN4-5 +5 V
PPSENS3 LED CLK
1
1 R2 2 1 R3 2 1 R4 2 1 2 R5
CN3-12
3
+24 V +24 V N.C PFCL1 PFCL2 CCL +5 V SG
PPSENS1
CN1-1 CN1-2 CN1-3 CN1-4 CN1-5 CN1-6 CN1-7 CN1-8 CN1-9 CN1-10 CN1-11
1 2 3 4 5 6 7 8 9 1 R8 2 1 R7 2 1 R6 2
3 4 5 6 7 8 9 10 11
+5 V
PESENS LED CLK
+5 V
PPSENS2 LED CLK
N.C SCSW
1 CN5-1 CN5-2 +24 V CCL +24 V PFCL2 +24 V PFCL1 N.C N.C 1 2 3 4 5 6 7 8 2 3 4 5 6 7 8 9 10 11
CN2-1 CN2-2 CN2-3 CN2-4 CN2-5 CN2-6 CN2-7 CN2-8 CN2-9 CN2-10 CN2-11 CN2-12 CN2-13
1 2 3 4 5
12 13
N.C N.C
CN8-1
1 2 3
CN8-2 CN8-3
1 2 3 4 1 R9 2
CN7-4
N.C
8
1 R10 2
3-7-45
E E A
A E A 2AD 8 7 6 5 4 3 2 1
E A
3-7-46 3-7-26
A
24 V 24 V PG PG 5V 5V SG SG
Unused pins
CN1-5 CN1-6 CN2-4 CN2-5 CN3-14 CN6-A1 CN6-A2 CN6-A3
Mi2 (11P) White Mi2 (12P) White Mi2 (11P) Red Mi2 (11P) Red 11 10 9 8 7 6 5 4 3 2 1 1211 10 9 8 7 6 5 4 3 2 1 11 10 9 8 7 6 5 4 3 2 1 1211 10 9 8 7 6 5 4 3 2 1
E A C
OSSW OFSW OSBSW CN5-A3 CN5-A2 CN5-A1 CN5-A5 CN5-A4 OFCL 24 V
E A
FG FG DFTSW OSLSW DFSSW1 DFSSW2 OSWSW DF SHORT FG FG CN3-4 CN3-5 CN3-6 CN3-7 CN3-8 CN3-11 CN3-12 CN3-13 CN3-1 CN3-2 CN3-3 SBPSOL2 SBPSOL1 24 V
SBPSOL OFCL
EFS SOL
D E
EFSSOL OFCL SBPSOL1 SBPSOL2 OSLED PCB (GN) OSLED PCB (RED)
CN5-A7 CN5-A6
EFSSOL 24 V
OCM M1 OCM M2 OCM M3 OCM Vref OCM CWB OCM CLK OCM RET OCM ENABLE OFM CWB OFM CLK OFM RET OFM ENABLE OFSOL1 OFSOL2 SBFSSOL CN2-1 CN2-2 CN2-3 CN2-6 CN2-7 CN2-8 CN2-9 CN2-10 CN2-11 CN2-12 CN2-13 CN2-14 CN2-15 CN2-16 CN2-17 CN2-18 CN2-19 CN2-20 CN2-21 CN2-22 CN3-9 CN3-10
CN5-B8 CN5-B7
SBFSSOL 24 V
SB FS SOL
DFDPCB
CN A-1 CN A-2 CN A-3 CN A-4 CN A-5 CN A-6 CN A-7 CN A-8 CN A-9 CN A-10 CN A-11 CN A-12 CN A-13 CN A-14 CN A-15 CN A-16 CN A-17 CN A-18 CN A-19 CN A-20 CN A-21 CN A-22 CN A-23 CN B-1 CN B-2 CN B-3 CN B-4 CN B-5 CN B-6 CN B-7 CN B-8 CN B-9 CN B-10 CN B-11 CN B-12 CN B-13 CN B-14 CN B-15 CN B-16 CN B-17 CN B-18 CN B-19 CN B-20 CN B-21 CN B-22 CN B-23 OFSOL2 CN5-B13 OFSOL1 CN5-B12 24 V CN5-B11 CN5-A13 CN5-A12 CN5-A11 CN5-A10 CN5-A9 CN5-A8 OSLEDPCB (GN) SG OSLEDPCB (RED) CN6-B9 CN6-B8 CN6-B7 OCM B OCM A OCM B OCM A OCM BCOM 24 V (VEN) OCM ACOM 24 V (VEN)
OFSOL
F
OSLED PCB OSW SW
OCM
OFM
G H I J
5V OSWSW SG
OFM B OFM A OFM B OFM A OFM BCOM 24 V (VEN) OFM ACOM 24 V (VEN)
5V OSLSW SG
CN6-A12 CN6-A11 CN6-A10 CN4-1 5V DFTSW SG CN6-A15 CN6-A14 CN6-A13 DFSSW1 2 DFSSW2 2 24 V CN4-2 5V OFSW SG CN6-B4 CN6-B5 CN6-B6 CN4-3 5V OSSW SG CN6-B1 CN6-B2 CN6-B3 CN4-4 1 1 3 3 CN6-A6 CN6-A5 CN6-A4 5V OSBSW SG 24 V (VEN)
H I
DFSSW2 DFSSW1
A E
A E A
8
5.1 V 22 120 V 42 35 24 43 25 LIVE LIVE 37 Finisher SRDF 26 38 23 36 N.C N.C SLEEP SIG G(5 V) E 5.1 V Z CROSS SIG E 5.1 V G(5 V) E 5.1 V G(5 V) 5.1 V G(5 V) N.C NEUTRAL NEUTRAL 220-240 V 1 2 3 R24 V
A10 A9
Shield box
1 2 4 CLMU DUPRSW 5 DUPPCSW 6 DUPESW STKSW 8A3 SRHPSW 2 1 SBFSSOL DUPFWDSOL DUPPTSOL
R24 V 7
A8 A7
1 2
CLML 8A4 8 8A5 3 5V 5V 5V 5V 5V GND GND GND GND GND 2 1 R24 V R24 V R24 V R24 V 8B10 R24 V SRM A R24 V SRM B SRM A_ SRM B_ 8B11 PSWL 24 V 24 V 24 V 24 V G(24 V) G(24 V) G(24 V) G(24 V) G(5 V) E 5.1 V 24 V 24 V G(24 V) G(24 V) G(5 V) G(5 V) E 5.1 V E 5.1 V PSWU LICSWL PFCLL LICSWU PFCLU
B2 B1
EHUMSENS
12A5 4 4 4 9 3 2 1 PRY REM 1 1 2 2 1 1 3 3 2 1 4 3 2 1 12B1 12B10 1 2 12B8 BYPPFCL BYPPLSW BYPEDSW BYPPWSW 12B7 12B6 4 2 4 7 4 8 4 3
SSW2
EPCB
10 9
43or44
33or34
23or24
A1orA2
B1 B2 B3 B4 B5 B6 B7 B8 B9
3A3
3A2
3A1
3A9
3A8
3A7
3A6
3A5
3A4
8A9
8A8
8A7
43or44
33or34
23or24
139
138
137
136
135
134
133
132
131
926
925
924
923
922
921
920
919
A1orA2
8A10
1315
1314
1313
1312
1311
1310
R24 V
1
119 118
G(5 V) G(5 V)
10 9
N.C 4 3 2 1 4
R24 V R24 V 5A13 5A12 5A10 5A9 5A7 5A6 PLSWU PLSWL 5A8 FSSOL 5A11 FSSW SBESW G(24 V) G(24 V) G(5 V) 5V PCM REM PCM LOCK PCM CLK N.C FSW PFSW1 PFSW2 PFSW3 PFSW4 5A14
TH2
GND 2B2 2B3 2B4 2B9 2B12 2B11 8 7 6 5 4 3 2 1 16 15 14 13 12 11 10 9 2B10 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 9 2B6 2B5 N.C N.C 24 V 24 V 24 V 24 V G(5 V) FG G(24 V) G(24 V) G(24 V) E 5.1 V 2B7 2B8 FRXD G(5 V) 2A12 GND 2A11 2A10 2A9 TLS 5V TRM 2A7 2A8 2A5 2A6 2A3 2A4 2A1 N.C 2A2 2B1 2 2 N.C 5B14 5B13 1 1 TRM TFM TFM R24 V IFFM REM R24 V CL REM G(24 V) FTXD 8 7 6 5 4 3 2 1 16 15 14 13 12 11 10 9 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 9 TLDS 5V TNS CONT R24 V TNS SIG GND
Finisher (Option)
177 173 174 175 Key card*3 4 (Option) 3 Key counter 2 (Option) 1 4 3 2 1 176 1713 1714 1715 1716
201
19B10 19A10 19B9 19A9 19B8 19A8 19B7 19A7 19B6 19A6 19B5 19A5 19B4 19A4 19B3 19A3 19B2 19A2 19B1 19A1
e
214 213 212 211 215 185 189 188 187 186 183 184 182 181 216
1811
1812
1810
IFFM
62 G(24 V) 61
E 5.1 V 64 G(5 V) 63
1 2 3 4 5 6 7 8 9 10 11 12 13 14
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
11 12 TB 14 9 DB REM GND(5 V) DB CONT TC REM 7 TC CONT 6 18 19 CN2 110 111 112 113 SC REM 5 SC CONT 4 ST ALM 3 GND(24 V) 2 R24 V 1 13 MC ALM GRID CONT
MC REM
OMPCB
SMPCB
OLPCB
14 13 12 11 10 9 8 7 6 5 4 3 2 1
1 2 3 4 5 6 7 8 9 10 111213 14
TC
15 8 16 17
SHPSW
HVTPCB
SC
1 2 3 4 5 6 7 8 9 10 111213
1 2 3 4 5
1 1
5B2 5B1
165 8 7 RXD G( 5V) TXD G(5 V) 6 7 SET SIG 8 R24 V (METER PULSE) 166 1 1612 2 1611 3 1610 4 169 6 167 168
SCPCB
CN 1
CN 1
CN 1
MCPCB2
MCPCB1
Vout 1/2 1 G(5 V) 2 7A5
11 10 9 8 7 6 5 4 3 2 1
A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11
A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11
1 2 3 4 5 6 7 8 9 10 11
12 11 10 12 11 10
9 9
8 8
CN 2
CN 3
CN 4
5 12 11 10 9
9 10
4 3 2 1
PM
13 12 11 10
GRID
INPCB
5B11
1 2 3 4 5
LSU
5B12
7 7
6 6
CN 1
TRM
+ +
VLCD VEE(23 V) XD3 XD2 XD1 XD0 23 V G(5 V) 5V XSCL LP DIN N.C LCD.REM
Touch panel
CN 1
24 V 23 V G(24 V) CNT.VR DIG KEY_L1 DIG KEY_L2 DIG KEY_L3 SCAN_L1 SCAN_L2 SCAN_L3 DIG LED_L1 DIG LED_L2 DIG LED_L3 DIG LED_L4 CFL REM 5V 5V N.C
61 62 63 64 65 66 67 68 69 610 611 R5 V G(5 V) /ADJUST 1 G(5 V) /ADJUST 2 G(5 V) /EN G(5 V) /VD1 + /VD1 /VD2 + /VD2 G(5 V) PM CLOK G(5 V) PM START PM READY
G(5 V) TXD MMI MMIACK G(5 V) RXD MMI ENGACK MMI MMI ERROR ENG ERROR MMI RESET MMI G(5 V) MMI TH
611 610 6 9 6 8 6 7 6 6 6 5 6 4 6 3 6 2 6 1 11 10 9 8 7 6 5 4 3 2 1 1 2 3 4 5 6 7 8 9 10 11
314 313 312 311 310 3 9 3 8 3 7 3 6 3 5 3 4 3 3 3 2 3 1 1 2 3 4 5 6 7 8 9 10 111213 85 84 83 82 81 91 92 93 94 713 712 711 710 79 78 77 76 75 74 73 72 71
5V BUZZER N.C DIG LED_R3 DIG LED_R2 DIG LED_R1 SCAN_R4 SCAN_R3 SCAN_R2 SCAN_R1 DIG KEY_R4 DIG KEY_R3 DIG KEY_R2 DIG KEY_R1
MPCB
G (Analog) G (Analog) 61 62 63 64 65 66 67
27 26 25 24 23 22 21
51 52 53 54 55 56 57 58 59 510 511
111 110 19 18 17 16 15 14 13 12 11
533 534 531 532 529 530 527 528 525 526 523 524 521 522 519 520 517 518 515 516 513 514 511 512 59 510 57 58 55 56 53 54 51 52
RESET SCN G(5 V) SID 7 TXD SCN SID 7+ G(5 V) SID 6 RXD SCN SID 6+ SCAN START SID 5 ENGAKU SCN SID 5+ ENG HEDER SCN SID 4 SC TIM SID 4+ SCNACK SID 3 SCN HEADER SID 3+ G(5 V) SID 2 SCN CLK SID 2+ SCN CLK+ SID 1 SMRE SID 1+ SMRE + SID 0 SOVSYNC SID 0+ SOVSYNC +
81 82 83 84 85 86 87 88 89 810 811 812 813 814 815 816 817 818 819 820 821 822 823 824 825 826 827 828 829 830 831 832 833 834
FG FG
7A4
OSD12
Vin 1/2 3 5V 4 LED 1/2 5 Vout 3/4 1 G(5 V) 2 5.1 V G(5 V) E 5.1 V G(5 V) G(5 V) G(5 V) E 5.1 V E 5.1 V E 5.1 V OSD34 Vin 3/4 3 5V 4 LED 3/4 5 Vout 5/6 1 5 5 4 4 3 2 3 2 1 1 G(5 V) 2 OSD56 Vin 5/6 3 5V 4 LED 5/6 5 Vout 7/8 1 G(5 V) 2 105 101 103 102 104 22 21 22 21 22 21
7A3 7A2 7A1 7A10 7A9 7A8 7A7 7A6 7B10 7B9 7B8 7B7 7B6 7B5 SLEEP SIG
OCM OCM OCM OCM OCM OCM OCM OCM OFM OFM OFM
12 11 10 9 8 7 6 5 4 3 2 1
B12 B13 B14 B15 B16 B17 B18 B19 B20 B21 B22 B23
B12 B13 B14 B15 B16 B17 B18 B19 B20 B21 B22 B23
1 2 3 4 5 6 7 8 9 10 11 12
7B4
12 11 10 9 8 7 6 5 4 3 2 1
1 2 3 4 5 6 7 8 9 10 11 12
A12 A13 A14 A15 A16 A17 A18 A19 A20 A21 A22 A23
A12 A13 A14 A15 A16 A17 A18 B19 A20 A21 A22 A23
OSD78
Vin 7/8 3 5V 4
7B3 7B2
LED 7/8 5
7B1
21 91 92 93 94 95 96 22 23 CFL 24 25 26 36 35 34 33 32 31
41 42 43 51 52 53 ORPCB
3 2 1
179
SM B_ 6 24 V 5 4 SM B SM A 3 24 V 2 1 SM A_
11 12 13 14 15 16 3
21 24 EL
N.C
N.C
N.C
A1 A2 A3 A4 A5 A6 A7 A8 A9
7 7
8 8
1 1
3 3
2 2
11 10 9 11 10 9
ESW
(Service part)
(Service part)
R24 V
KC COUNT
DF11(8P) 5 6 7 3 4 1
PFM CLK
9
PWSWU*2
8 2
PFM LOCK
8
PWSWL*2
PFM
R24 V
2
G(24 V)
3
117 5V 5V 5V 5V 5V 5V 5V GND GND GND GND GND GND GND FSW 116 115 114 R24 V G(5 V) FSSW G(5 V) PFSW4 PFSW3 PFSW2 PFSW1 SBESW FSSOL2 FSSOL1 PLSWL
A9 A10 A11 A3 A4 A5 A6 A7 A8
G(24 V)
4
G(5 V)
5
PLSWU
PWSWL DIG 2
PWSWL DIG 1
PWSWL DIG 0
PWSWU DIG 2
PWSWU DIG 1
PWSWU DIG 0
5V
6
PFM REM
7
CCM
DM REM
B5 B4 B3 B2 B1
RSW
12B5
1 A2 A3 A4 A5
10 11 12 13 14 15
BYPPSW
BYPSOL
HUMPCB
PCFM
1 2 3 3 2 1
DM
12B9
R24 V
1 3
2 2
3 1
1 1
2 2
3 3
CFM1
CFM2
A6 A5 B10
4 1
3 2
2 3
1 4
N.C
SSW1 SOURCE
1 5
2 4
3 3
4 2
5 1
12A6
2 1
1 2
N.C(5 V)
2 1
1 2
N.C(GND)
7 1
6 2
5 3
4 4
2 6
3 5
1 7
BYPPWSW DIG 2
BYPPWSW DIG 1
BYPPWSW DIG 0
1 7
2 6
3 5
4 4
5 3
6 2
7 1
N.C(5 V)
2 1
1 2
2 1
1 2
A
CLML 2 1 3 2 1 3 2 1 3 2 1 3 2 1 2 1 3 3 1 2 1
STKSW
DUPESW
SRHPSW
DUPRSW
9 10 11 12
DUPPCSW
1 3 RCL
OMPCB
B4 B3
FCL4 FCL4 8B9 51 52 53 54 61 62 63 64 79 71 75 3 TB 1 TB 2 QR/P15(40P) DF11(18P) R24 V 12A1 1 2 1 2 5V 5V 5V 5V 5V SCPCB GND GND GND GND GND GND R24 V R24 V R24 V R24 V R24 V SRM A SRM B STKSW 12A2
A10 A9
17 18 15 16 13 14 11 12 9 10 7
18 17 11 13 15 12 14 16 8
6 10 5
FCL5
SRM A_
SRM B_
SET SIG
DUPESW
SRHPSW
DUPRSW
DUPPCSW
SBFSSOL1
SBFSSOL2
DUPPTSOL
DUPFWDSOL
1 2 FCL1
Noise filter
FCL1 2 1
5V
5V
G(5 V)
G(5 V)
SMPCB
G(5 V) 5V
G(5 V)
5V
PSWL
PSWU
PFCLU
PFCLL
R24 V
R24 V
LICSWL
LICSWU
PSPCB
R24 V 12A7 N.C N.C N.C N.C 12A8 N.C 72 13 16 27 39 17 44 45 24 V G(24 V) E 5.1 V G(5 V) 12 G(24 V) H1 REM H2 REM R24 V 24 V
A4 A3
1 2 FCL2 2 1
N.C(R24 V)
FCL2
N.C(G) 918
B
91 92 98 96 94 97 95 93 99 911 152 156 154 158 151 155 153 157 159 102 101 104 103 106 105 108 107 109 913 914 910 912 916 915 917 R24 V 12A9 12A10 6 2 6 3 5A4 5A3 5A2 5A1 5A5 6 4 6 6 6 7 6 8 6 5 4 5 14B1 14B2 14B3 14B4 14B5 14B6 14B7 14B8 14B9 14A9 14A1 14A8 14A6 14A7 14A5 14A4 14A3 14A2 3B2 3B1 6 1
A2 A1
1511
1011
1512
1510
1514
1516
1513
1515
1010
1012
1014
1013
1016
1015
1018
1017
1 2 FCL3 2 1
FCL3 3B6 3B5 3B4 3B3 8B1 8B2 8B3 8B4 8B5 8B6 8B7 R24 V 3A10 3A11 B6 B7
5V RSW R24 V R24 V G(5 V) R24 V A10 A11 A12 A13 A14 A2 A1
2 1
TB 3
TB 4
102
101
9 1
81
93
82
LIVE
NEUTRAL
NEUTRAL
24 V OUT
G(5 V)
BYPPFCL
N.C(GND)
BYPPLSW
BYPEDSW
MSW
1 1
1 1
SSW1
4 6 4 1 3 3
SSW1
2 3 8 7 4
3 3
C
5 6 5 4 3 2 1 8 7 6 5 4 3 2 1
SSW3
SSW2
6 7 8 9 10 1 2 3 4 5 6 7 8 9 10
1 3 2 1 1 3 2
SSW3 A
PRY
5 4 3 2 1 1 2 3 4 5
D
10 9 1 2 3 8 4 7 5 6 6 5 7 4 8 3 9 2 1 10
PCM 1 1 3 2 2 2
24 V 5V 4 3 2 1 G(24 V) G(5 V) 4 3 2 1
H2
H1
2 FTH
Fixing unit
TLDS 1 3 4 4 3 1 1 5 5 1 2 2 2
850W
850W
TH1
E
TNS 3 3 6 6 3 4 4 7 7 8 8 9 9 G(5 V) RESET SET SIG 3 2 4 TLS 1 3 3 1 1 2 2 1 1 TFM 1 3 3 1
1 2
1 2
9 10
2 CH
2 OPH
24 V
5.1 V
G(24 V)
5-3
5-4
24 V
LCD
F
1 1 CL 2 Cleaning earth 2 MC
1 2 3 4 5 6 2 1 3 2 1
6 5 4 3 2 1 ODSW SM
G
DB
MMD* (Option)
CCDPCB
H I J 8
*1 For metric specifications only. *2 For inch specifications only. *3 For 120 V specifications only.
11 10 9 8 7 6 5 4 3 2 1
B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 B11 B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 B11
1 2 3 4 5 6 7 8 9 10 11
SRDF
*1
2AD
3-7-47
2AD
SBSFSOL OFSOL2 OFSOL1 OFM ENABLE OFM RET OFM CLK OFM CWB OCM ENABLE OCM RET OCM CLK OCM CWB OCM Vref OCM M3 OCM M2 OCM M1
2
C5-A10 GY C5-A12 GY C5-A13 RD C5-A11 GY C5-A1 GY C5-A2 GY C5-A3 GY C5-A4 GY C5-A9 GY C5-A5 GY C5-B2 GY C5-B3 GY C5-B4 GY C5-B5 GY C5-B6 GY C5-A8 RD C5-B1 RD
2
DF SHORT OSWSW DFSSW2 DFSSW1 OSLSW DFTSW FG FG Mi2 (12P) WHITE G (5 V) G (5 V) E5V E5V G (24 V) G (24 V) 24 V 24 V Mi2 (11P) WHITE C1-10 C1-9 C1-8 C1-7 C1-4 C1-3 C1-2 C1-1 OSBSW OFSW OSSW
C17
C15
C13
C11
1 24 V 2 SBPSOL1
3 SBPSOL2
3 OCM A
C18
C16
C14
C6-A13 GY
C6-A14 GY
C6-A15 RD
C12
3 OFM A
1 24 V 2 OFCL
C3-3 C3-2 C3-1 C3-13 C3-12 C3-11 C3-8 C3-7 C3-6 C3-5 C3-4 M1 GN M1 GN
C3-10 C3-9 C2-22 C2-21 C2-20 C2-19 C2-18 C2-17 C2-16 C2-15 C2-14 C2-13 C2-12 C2-11 C2-10 C2-9 C2-8 C2-7 C2-6 C2-3 C2-2 C2-1
1 2 3 4 5 6 7 8 9 10 11 12 1 2 3 4 5 6 7 8 9 10 11 1 2 3 4 5 6 7 8 9 10 11 12 1 2 3 4 5 6 7 8 9 10 11
B-23 B-22 B-21 B-20 B-19 B-18 B-17 B-16 B-15 B-14 B-13 B-12 B-11 B-10 B-9 B-8 B-7 B-6 B-5 B-4 B-3 B-2 B-1 A-23 A-22 A-21 A-20 A-19 A-18 A-17 A-16 A-15 A-14 A-13 A-12 A-11 A-10 A-9 A-8 A-7 A-6 A-5 A-4 A-3 A-2 A-1
C10
C9
C8
C7
3
M1
C8-4 C8-3 C8-2 C8-12 C8-11 C8-10 C8-9 C8-8 C10-3 C10-2 C8-7 C8-6 C8-5 1 2 3 4 5 6 7 8 9 10 11 12 13 14 C9-11 C9-10 C9-9
C20
WE
YW
WE
YW
OE
GN
OE
RD
RD
RD
BN
BK
BK
BE
BK
BK
BE
1 SG 2 DFTSW
3 5V
OCM
C6-A6 GY C6-A5 GY C6-A4 GY
C21
OCM Vref OCM CWB OCM CLK OCM RET OCM ENABLE OFM CWB OFM CLK OFM RET OFM ENABLE OFSOL (A) OFSOL (R) SBSFSOL
OSSW OFSW OSBSW DFTSW OSLSW DFSSW1 DFSSW2 OSWSW OSLED (GN) OSLED (RED)
C19
OE
BE
LB
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
SBP SOL
OF CL
OFM
C9-8 C9-7 C9-6 C9-5 C9-4 C9-3 C9-2 C9-1 C10-12 C10-11 C10-10 C10-9 C10-8 C10-7 C10-6 C10-5 C10-4
C7-1 GN C7-2 GN
OSBSW
OSBSW
5V
SG
DFT SW
RD
C23
1 24 V 2 OFSOL1 3 OFSOL2
C22
3 2 1
DFDPCB
OFSOL
BN GN
C1
(CN1)
C3
(CN3) A-1 A-2 A-3 A-4 A-5 A-6 A-7 A-8 A-9 A-10 A-11 A-12 A-13 A-14 A-15
C6
(CN6) SG 5V SG 5V OSLED (GN) SG OSLED (RED) SG OFSW 5V SG OSSW 5V B-15 B-14 B-13 B-12 B-11 B-10 B-9 B-8 B-7 B-6 B-5 B-4 B-3 B-2 B-1
C2
(CN2)
4
C5
(CN5)
OE
C31
1 5V 2 OFSW 3 SG
C30
3 2 1
OFSW
YW BE
C32
Wire color Mark Black BK Brown BN Yellow YW Green GN Blue BE White WE PK Pink Red RD Orange OE Light blue LB Purple PE Gray GY Green/yellow GN/YW
OSLED PCB
1 2 3
PG PG 24 V 24 V
C4
(CN4) P1-3 RD P2-3 RD P2-1 RD P1-2 RD 4 3 2 1 DFSSW1 DFSSW2 24 V 24 V (VEN)
P2
24 V 1 2 3 C4-2 RD P1-1 RD C4-3 RD
C19-3 GY C19-2 GY C19-1 GY C10-6 GY C10-5 GY C10-4 GY C10-3 GY C10-2 GY C10-1 GY C20-3 GY C20-2 GY C20-1 RD
C15-3 GY C15-2 GY C15-1 GY C13-2 GY C13-1 GY C26-2 GY C26-1 GY C17-6 GY C17-5 GY C17-4 GY C17-3 GY C17-2 GY C17-1 RD
A-1 A-2 A-3 A-4 A-5 A-6 A-7 A-8 A-9 A-10 A-11 A-12 A-13
24 V SBPSOL (A) SBPSOL (R) 24 V OFCL 24 V EFSSOL OCM ACOM 24 V (VEN) OCM BCOM 24 V (VEN) OCM A OCM _ B OCM A _ OCM B
B-13 B-12 B-11 B-10 24 V B-9 SBSFSOL B-8 24 V _ B-7 OFM B B-6 _ OFM A B-5 OFM B B-4 OFM A B-3 OFM BCOM 24 V (VEM) B-2 OFM ACOM 24 V (VEN) B-1
DFSSW2
24 V (VEN) DFSSW2
OE
C25
1 5V 2 OSSW 3 SG
C24
3 2 1
P1
P2-2 RD C4-1 RD C4-4 RD
DFSSW1
1 24 V 2 24 V (VEN) 3 DFSSW1
OSSW
LB BE
C10
C6-A12 GY C6-A11 GY C6-A10 GY C6-A9 GY C6-A8 GY C6-A7 GY 1 2 3 4 5 6 5V OSLSW SG 5V OSWSW SG
C9
6 5 4 3 2 1 C7-1 OE C7-2 GY C7-3 BE C8-1 OE C8-2 YW C8-3 BE
EFSSOL
BE BE
C27
1 24 V 2 EFSSOL
C26
2 1
Original table C8
C9-3 OE C9-2 YW C9-1 BE 1 5V 2 OSWSW 3 SG OE YW BE
C5-A6 GY C5-A7 GY
C7 OSWSW
C9-6 OE C9-5 GY C9-4 BE
OSLSW
1 5V 2 OSLSW 3 SG
SBSFSOL
BE BE
C29
1 24 V 2 SBSFSOL
C28
2 1
C5-B7 GY C5-B8 GY
3-7-48
2AD I
CN-1 CN-3 CN-2 CN-1 CN-3 CN-2 CN-1 CN-3 CN-2 CN-1 CN-3 CN-2
DLSW1
RD BE OE GN LB GY PK BN PL
5V G (5 V) 24 V G (24 V) DECK TXD G (5 V) DECK RXD G (5 V) PFSW4* LED CLK N.C N.C DOSSW PESENS PPSENS2 DLSW1 UPSW1 DLSW2 UPSW2 PPSENS3 CN1-1 CN1-2 CN1-3 CN1-4 CN1-5 CN1-6 CN1-7 CN1-8 CN1-9 CN1-10 CN1-11
UPSW1
INTERFACE
BK CN-1 WE CN-2
AC-L AC-N
RD RD
LB LB LB LB LB LB LB LB LB LB LB
DCNJ-11 DCNJ-10 DCNJ-9 DCNJ-8 DCNJ-7 DCNJ-6 DCNJ-5 DCNJ-4 DCNJ-3 DCNJ-2 DCNJ-1
LED CLK N.C N.C DOSSW PESENS PPSENS2 DLSW1 UPSW1 DLSW2 UPSW2 PPSENS3
DCNP-11 DCNP-10 DCNP-9 DCNP-8 DCNP-7 DCNP-6 DCNP-5 DCNP-4 DCNP-3 DCNP-2 DCNP-1
WE WE WE WE WE WE WE WE WE WE WE
(Service part)
DH2
RD CN-1 RD CN-2
AC-N AC-L
RD RD +24 V +24 V N.C PFCL1 PFCL2 CCL +5 V SGND PPSENS1 N.C SCSW N.C CN4-1 CN4-2 CN4-3 CN4-4 CN4-5 CN4-6 CN4-7 CN4-8 CN4-9 CN4-10 CN4-11 CN4-12
LED CLK N.C N.C DOSSW PESENS PPSENS2 DLSW1 UPSW1 DLSW2 UPSW2 PPSENS3 N.C N.C +24 V +24 V N.C PFCL1 PFCL2 CCL +5 V SGND PPSENS1 N.C SCSW
CN2-1 CN2-2 CN2-3 CN2-4 CN2-5 CN2-6 CN2-7 CN2-8 CN2-9 CN2-10 CN2-11 CN2-12 CN2-13 CN1-1 CN1-2 CN1-3 CN1-4 CN1-5 CN1-6 CN1-7 CN1-8 CN1-9 CN1-10 CN1-11
DLSW2
2
UPSW2
(Service part)
DH1
RD CN-1 RD CN-2
AC-N AC-L
RD RD
WE WE WE WE WE WE WE WE WE WE WE
DCNJ-22 DCNJ-21 DCNJ-20 DCNJ-19 DCNJ-18 DCNJ-17 DCNJ-16 DCNJ-15 DCNJ-14 DCNJ-13 DCNJ-12
+24 V +24 V N.C PFCL1 PFCL2 CCL +5 V SGND PPSENS1 N.C SCSW
DCNP-22 DCNP-21 DCNP-20 DCNP-19 DCNP-18 DCNP-17 DCNP-16 DCNP-15 DCNP-14 DCNP-13 DCNP-12
LB LB LB LB LB LB LB LB LB LB LB
LB LB LB LB LB LB LB LB LB
PPSENS3
PESENS
PPSENS2
WE WE WE
4
PPSENS1
CN-2 CN-1
PDM1 +24 V WE WE RD RD WE WE WE RD RD RD CN7-1 CN7-2 CN7-3 CN7-4 CN7-5 CN7-6 CN7-7 CN7-8 CN7-9 CN7-10 PDM1 +24 V +24 V PDM2 +5 V SGND PDMSENS1 +5 V SGND PDMSENS2 +5 V CN-3 SGND CN-2 PLDSENS1 CN-1 +24 V CCL +24 V PFCL2 +24 V PFCL1 N. C N. C CN5-1 CN5-2 CN5-3 CN5-4 CN5-5 CN5-6 CN5-7 CN5-8 OE OE OE OE OE OE
BE BE BE BE BE BE
CCL
PDM1
5
PFCL2
PDMSENS1
+5 V SGND PDMSENS1
6
PDM2
CN-2 CN-1
+24 V PDM2
WE WE WE LB LB LB
PLDSENS1
PFCL1
PLDSENS2 RD RD RD RD RD
6
+5 V SGND SCSW DOSSW +24 V CN6-1 CN6-2 CN6-3 CN6-4 CN6-5 +5 V SGND SCSW CN-3 CN-2 CN-1
PDMSENS2
+5 V SGND PDMSENS2
SCSW
7
CN-5 CN-4 CN-3 CN-2 CN-1 +24 V PGND CM PWM +5 V CM CLK OE OE OE OE OE CN12-1 CN12-2 CN12-3 CN12-4 CN12-5 +24 V PGND CM PWM +5 V CM CLK
CM
Wire color BLACK BROWN YELLOW GREEN BLUE WHITE PINK RED ORANGE LIGHT BLUE PURPLE
Mark BK BN YW GN BE WE PK RD OE LB PL
DOSSW +24 V
N. C N. C N. C
8
PDMPCB I/FPCB
8
* Switch on the copier
3-7-49
2AD B C D E F G H I J
WE WE WE WE WE WE WE WE WE WE WE
C224-11 C224-10 C224-9 C224-8 C224-7 C224-6 C224-5 C224-4 C224-3 C224-2 C224-1
C207 (CN7)
WE WE WE WE WE WE WE WE WE WE WE
C225-11 C225-10 C225-9 C225-8 C225-7 C225-6 C225-5 C225-4 C225-3 C225-2 C225-1
SCPCB
WE WE WE WE WE WE WE WE WE WE WE WE WE WE WE WE WE WE WE WE WE WE WE WE WE
C226-11 C226-10 C226-9 C226-8 C226-7 C226-6 C226-5 C226-4 C226-3 C226-2 C226-1 C215-1 C215-2 C215-3 C215-4 C215-5 C215-6 C215-7 C215-8 C215-9 C215-10 C215-11 C215-12 C215-13 C215-14 14 13 12 11 10 9 8 7 6 5 4 3 2 1
C203 (CN1)
LED 1/2 5V Vin 1/2 G (5 V) Vout 1/2 LED 3/4 5V Vin 3/4 G (5 V) Vout 3/4 LED 7/8 5V Vin 7/8 G (5 V) Vout 7/8 LED 5/6 5V Vin 5/6 G (5 V) Vout 5/6
A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 B1 B2 B3 B4 B5 B6 B7 B8 B9 B10
BK BK BK BK BK BK BK BK BK BK BK BK BK BK BK BK BK BK BK BK
C222-5 C222-4 C222-3 C222-2 C222-1 C221-5 C221-4 C221-3 C221-2 C221-1 C223-5 C223-4 C223-3 C223-2 C223-1 C210-5 C210-4 C210-3 C210-2 C210-1
C202 (CN3)
BK BK BK BK BK
C223
1 2 3 4 5 Vout 7/8 G (5 V) Vin 7/8 5V LED 7/8
Wire color BLACK BROWN YELLOW GREEN BLUE WHITE PINK RED ORANGE LIGHT BLUE PURPLE GRAY GREEN/YELLOW
Mark BK BN YW GN BE WE PK RD OE LB PE GY GN/YW
C201 (CN2)
OSD78*
2
1 2 3 4 5 6 7 8 9 10 11 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 A20 A21 A22 A23 B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 B11 B12 B13 B14 B15 B16 B17 B18 B19 B20 B21 B22 B23 24 V 24 V G (24 V) G (24 V) E 5V E 5V G (5 V) G (5 V) F.G. F.G. DFTSW OSLSW DFSSW1 DFSSW2 OSWSW DF SHORT OSSW OFSW OSBSW OCM M1 OCM M2 OCM M3 OCM Vref OCM CWB OCM CLK OCM RET OCM ENABLE OFM CWB OFM CLK OFM RET OFM ENABLE OFSOL1 OFSOL2 SBFSSOL EFSSOL OFCL SBPSOL1 SBPSOL2 OSLED (GN) OSLED (RED) -
BK BK BK BK BK
C222
1 2 3 4 5 Vout 1/2 G (5 V) Vin 1/2 5V LED 1/2
C170
OSD12 EL
CCDPCB
7 6 5 4 3 2 1
WE WE WE WE WE WE WE
1 2 3 4 5 6 7
C205 (CN6)
C208 (CN2)
BK WE
BK BK BK BK BK
C210
1 2 3 4 5 Vout 5/6 G (5 V) Vin 5/6 5V LED 5/6
OSD56
BK BK BK BK BK
C221
1 2 3 4 5 Vout 3/4 G (5 V) Vin 3/4 5V LED 3/4
WE
OSD34
C220(CN2) 2 3
4
WE
C1 1 2
INPCB C219(CN1)
1 2 3 4 5 6 G (24) G (24) 24 V 24 V EL EL
C3 (CN8)
WE WE WE WE WE WE WE WE WE WE WE
C203-12 C203-11 C203-10 C203-9 C203-8 C203-7 C203-6 C203-5 C203-4 C203-3 C203-2
1 2 3 4 5 6 7 8 9 10 11 12
C225
11 10 9 8 7 6 5 4 3 2 1
WE WE WE WE WE WE WE WE WE WE WE
1 2 3 4 5 6 7 8 9 10 11
C204 (CN4)
WE WE WE WE WE WE WE WE WE WE WE
C201-12 C201-11 C201-10 C201-9 C201-8 C201-7 C201-6 C201-5 C201-4 C201-3 C201-2
C206 (CN5)
C209 (CN1)
SRDF
1 2 3 4 5 6 7 8 9 10 11 12 1 2 3 4 5 6 7 8 9 10 11
C224
WE WE WE WE WE WE WE WE WE WE WE
C202-11 C202-10 C202-9 C202-8 C202-7 C202-6 C202-5 C202-4 C202-3 C202-2 C202-1
5
C226
WE WE WE
G (24) G (24) 24 V 24 V EL EL
C213 (CN5)
1 5V 2 ODSW 3 GND
1 2 3 4 5 6
SMPCB
OE 5V 1 3 GN SHPSW 2 2 BE GND 3 1
6
C216 (CN4) C218
3 2 1
SHPSW
1 2 3 4 5 6 7 8 9 10 11 12 13 14
1 2 3 4
1 2 3 4 5 6
6 5 4 3 2 1
WE WE WE WE WE WE
1 2 3 4 5 6
6 5 4 3 2 1
SM A_ 24 V SM A SM B 24 V SM B_
C214 (CN2)
G (24) 24 V G (5 V) E 5.1 V
1 2 3 4 5 6
W2 W1
WE WE WE WE WE WE WE WE WE WE WE WE WE WE
C204-1 C204-2 C204-3 C204-4 C204-5 C204-6 C204-7 C204-8 C204-9 C204-10 C204-11 C204-12 C204-13 C204-14
SM
14 13 12 11 10 9 8 7 6 5 4 3 2 1
PSPCB
8
MPCB *For metric specifications only. PSPCB
3-7-50
E A
8
FSW PFSW1 PFSW2 PFSW4 FCL1 FCL2
BE C169 OE C168 BE C167 OE C166
PFSW3
FCL3 FCL5
BYPPFCL
BYPPLSW
BYPEDSW
SSW3
BYPSOL
BYPPSW
BYPPWSW
A
1 E 5.1 V 2 G(5 V) 1 E 5.1 V 2 G(5 V) FSW 5V G(5 V) 3 2 1 PFSW1 3 2 5V G(5 V) 1 OE C1626 OE C1627 BE C1581 BE C1582 PE C1591 BE C1583
C10(CN2)
C11(CN2)
C117
OE LB BE
C116
MCPCB2
MCPCB1
PFSW3 5V G(5 V)
C2
1 2 3 4 5 6
C124
1 2
C1
BK BK
BK R24 V BK FCL1
BK R24 V BK FCL5
Bypass table
BK R24 V BK FCL3
BK R24 V BK FCL2
C127 C120
3 2 1 3 2 1
5V 1 3 BYPPLSW 2 2 G(5 V) 3 1
3 2 1
SSW3 SOURCE 3 2 1
GN 3 1 OE 2 2 BE 1 3
GN 3 1 OE 2 2 BE 1 3 2 1 1 2 1 2 3 4 5 6
BYPPWSW DIG0
BYPEDSW 1
GN 3 1 OE 2 2 BE 1 3 2 1 1 2
P9
C122
C123
(Service part)
G(5 V) 2
C126 C125
R24 V 1 BYPPFCL 2
C119 C118
5V 3 G(5 V) 2 BYPPSW 1 R24 V 1 2 BYPSOL 3
C114
OPH
(CN1)
(CN1)
C109
C108
C107
C113
RD C673 RD C678
YW C56A2 2 1 1 2 YW C56A1 YW C576 YW C575 YW C574 YW C579 YW C578 YW C577 YW C5715 YW C5714 YW C5713 YW C5712 YW C5711 YW C5710 YW C56A8 YW C56A7 YW C56A10 YW C56A9
YW C56A4 2 1 YW C56A3 1 2
(CN3)
C3
(CN2)
C12(CN2)
OE BE YW RD RD BK BN
(CN1)
(CN4)
(Option)
Printer boad
OE LB BE BE YW PK PK PK BE 7 6 5 4 3 2 1 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 9 8 7 6 5 4 3 2 1
C106
C110
C130
B
4 3 2 1 10 1 9 2 8 3 7 4 6 5 5 6 4 7 3 8 2 9 1 10 10 1 9 2 8 3 7 4 6 5 5 6 4 7 3 8 2 9 1 10 1 2 3 4
R24 V R24 V G(24 V) G(24 V) G(5 V) 5V PFM RFM PFM LOCK PFM CLK
C4(CN5)
DM
Optical section
PFM
YW C1101 YW C1102 YW C1103 YW C1104 YW C1105 YW C1106 YW C1107 YW C1108 YW C1109 YW C1061 YW C1062 YW C1063 YW C1064 YW C1065 YW C1066 YW C1067
C129 C128
B9 B8 B7 B6 B5 B4 B3 B2 B1 A9 A8 A7 A6 A5 A4 A3 A2 A1
HUMPCB
B1 B2 B3 B4 B5 B6 B7 B8 B9 A1 A2 A3 A4 A5 A6 A7 A8 A9
C104
5V G(5 V) BYPPSW R24 V R24 V BYPPFCL BYPSOL G(5 V) BYPPWSW DIG 2 BYPPWSW DIG 1 BYPPWSW DIG 0 BYPEDSW G(5 V) G(5 V) BYPPLSW 5V
C54 (CN20)
FCL4
BK R24 V BK FCL4 2 1 WE C59B4 WE C59B3 1 2
C103
PFCLL
C53(CN14B) C52(CN14A)
BK R24 V BK RCL
SID 0 + SOVSYNC + SID 0 SOVSYNC SID 1 + SMRE + SID 1 SMRE SID 2 + SCN CLK + SID 2 SCN CLK SID 3 + G(5 V) SID 3 SCN HEADER SID 4 + SCANACK SID 4 SC TIM SID 5 + ENG HEADER SCN SID 5 ENGAKU SCN SID 6 + SCAN START SID 6 RD SCN SID 7 + G(5 V) SID 7 TD SCN RESET SCN G(5 V) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34
BK BN YW GN WE PK LB PE GY BK BN YW GN BE PK LB PE GY BK BN YW GN WE PK LB PE GY YW BK BE BN GN PE BE
34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
SOVSYNC + SID 0 + SOVSYNC SID 0 SMRE + SID 1 + SMRE SID 1 SCN CLK + SID 2 + SCN CLK SID 2 G(5 V) SID 3 + SCN HEADER SID 3 SCANACK SID 4 + SC TIM SID 4 ENG HEADER SCN SID 5 + ENGAKU SCN SID 5 SCAN START SID 6 + RD SCN SID 6 G(5 V) SID 7 + TD SCN SID 7 G(5 V) RESET SCN
PFCLU
LICSWL
LICSWU
C170
PSWL*2
PSWU*2
WE C59B2 3 1 2 2 WE C59B1 1 3
C169
G(24 V) 24 V G(5 V) E 5.1 V
C55 (CN12-B)
C
RCL
C102 C101 C99
5V G(5 V) PSWU 5V G(5 V) PSWL BK PFCLL BK R24 V BK PFCLU BK R24 V
YW C1282 YW C1283 YW C1284 YW C1285 YW C1286 YW C1287 YW C1288 YW C1289 YW C12810 DM CLK DM LOCK DM REM 5V G(5 V) G(24 V) G(24 V) R24 V R24 V
B10 B9 B8 B7 B6 B5 B4 B3 B2 B1 B1 B2 B3 B4 B5 B6 B7 B8 B9 B10
1 2 3 4 5 6 7 8 9 10 11
MPCB
RSW
5V RSW G(5 V) 3 1 2 2 1 3
(CN1)
(CN1)
3 5V 2 G(5 V) LICSWU 1
3 5V 2 G(5 V) LICSWL 1 3 2 1
3 2 1
C137
1 2
C134
C133
1 2
C56 (CN12-A)
C138
C100
CCM REV CCM FWD
CCM
2 1 1 2 YW C1221 YW C1222 YW C1251 YW C1252 R24 V FCL2 R24 V FCL3 15 14 13 12 11
YW YW YW YW YW 5 4 3 2 1 WE WE WE WE WE WE 1 2 3 4 5
7 6 5 4 3 2 1
1 2 3 4 5 6 7
C136
OE BE YW OE BE LB PE RD 1 2 3 4 5 6 7 8
C132
OE BE YW OE BE LB PE RD 1 2 3 4 5 6 7 8
C135
C131
PCFM
RD R24 V BK PCFM 2 1 1 2
C98
C97
A10 A9 A8 A7 A6 A5 A4 A3 A2 A1
A1 A2 A3 A4 A5 A6 A7 A8 A9 A10
EPCB
C5(CN6)
C57 (CN13)
D
C87
BE BE 3 2 1
WE C6523 WE C6524 WE C6525 WE C6526 WE C6519 WE C6520 WE C6521 WE C6522 WE C60A8 WE C60A7 WE C60A10 WE C60A9
G(5 V) TD MMI MMIACK G(5 V) RD MMI ENGACK MMI MMI ERROR ENG ERROR MMI RESET MMI G(5 V) MMI TH 10 9 8 7 6 5 4 3 2 1
1 2 3 4 5 6 7 8 9 10 11
11 10 9 8 7 6 5 4 3 2 1
BE C281 GN C282 BN C283 BE C284 YW C285 WE C286 PK C287 LB C288 PE C289 BE C2810 WE C28-11 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 FSW 5V GND PFSW1 5V GND PFSW2 5V GND PFSW3 5V GND PFSW4 5V GND
C96 C95
RD R24 V PE SBFSOL2 WE C6614 WE C6613 WE C6612
BK DUPPTSOL
YW C1151 YW C1152 YW C1153 YW C1154 YW C1155 YW C1156 YW C1191 YW C1192 YW C1193 YW C1231 YW C1232 YW C1233 YW C1261 YW C1262 YW C1263
C6(CN10)
5 4 3 2 1
BN OE BE GY OE
7 8 5 6 3 4 1 2
C142
C139
7 8 5 6 3 4 1 2 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
GN 3 YW 2 RD 1 BE BE 2 1
1 2 R24 V RD BK 2 1 CLMU
1 2 R24 V RD 2 1 CLML BK
C143 C140
C94
C9(CN7)
G(5 V) /VD2 /VD2 + /VD1 /VD1 + G(5 V) /EN G(5 V) /ADJUST2 G(5 V) /ADJUST1 G(5 V) R5 V
C8 (CN8)
G(5 V) /BD /BD + G(5 V) R5 V
C7 (CN9)
PM READY PM START G(5 V) PM CLOK
12 11 10 9 8 7 6 5 4 3 2 1
C16
C58 (CN15)
SRM
5 BK 4 PWSWL DIG0 BK 3 PWSWL DIG1 BK 2 PWSWL DIG2 BK 1 G(5 V) 5 BK 4 PWSWU DIG0 BK 3 PWSWU DIG1 BK 2 PWSWU DIG2 BK 1 G(5 V)
BE C1586 OE C1573 BE C1588 OE C1576 BE C1587 OE C1575 BN C1593 OE C1574 BE C1585 GY C1592 OE C1572
C144 C141
RD RD BK OE BN YW
C92 C93
G(5 V) 5V STKSW 1 2 3
1 2 3 4 5 6
BK RD BK RD RD RD LB GN WE YW SBFSOL1 R24 V DUPFWDSOL R24 V R24 V R24 V SRM A SRM B SRM A SRM B
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 2 1 4 3 6 5 8 7 10 9 12 11 14 13 16 15 18 17 WE C6610 WE C669 WE C668 WE C667 WE C666 WE C665 WE C664 WE C663 WE C662 WE C661 OE C1311 OE C1351 BK C1313 BN C1353 BE C1312 BE C1352 OE C1314 OE C1354 YW C1316 GN C1356 BE C1315 BE C1355 PE C1317 GY C1357 RD C1318 RD C1358
1 2 3 4 5 1 2 3 4 5 6 7 8 9 10 11 12 13 13 12 11 10 9 8 7 6 5 4 3 2 1 5 4 3 2 1
4 3 2 1 1 2 3 4
Duplex unit
STKSW
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
5V 5V LICSWU LICSWL G(5 V) G(5 V) 5V 5V PSWU PSWL G(5 V) G(5 V) PFCLU PFCLL R24 V R24 V
PE BN BE GN
WE WE WE WE WE WE WE WE WE WE WE WE WE
WE WE WE WE WE
PWSWL PWSWU
C91
3 5V G(5 V) 2 SRHPSW 1
CLML
CLMU
C59 (CN8-B)
E
C90
DUPESW 3 2 5V G(5 V) 1
1 2 3 4 5
1 2 3 4 5 6 7 8 9 10 11 12 13
PLSWU
C145
2 G(5 V) PLSWU 1
C146
6 5 4 3 2 1 5 4 3 2 1
C89
DUPPCSW 3
13 12 11 10 9 8 7 6 5 4 3 2 1
WE C971 WE C972 WE C973 WE C974 WE C975 WE C976 WE C977 WE C1031 WE C1032 WE C1021 WE C1023
5V G(5 V)
2 1
B11 B10 B9 B8 B7 B6 B5 B4 B3 B2 B1
B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 B11
5V RSW G(5 V) CCM REV CCM FWD R24 V PCFM REM R24 V FCL4 R24 V RCL
G(5 V) /VD2 /VD2 + /VD1 /VD1 + G(5 V) /EN G(5 V) /ADJUST2 G(5 V) /ADJUST1 G(5 V) R5 V
PLSWL
G(5 V) 2 PLSWL 1
YW 4 1 YW 3 2 YW 2 3 YW 1 4
C88
DUPPSW 3 2 5V G(5 V) 1
BE YW OE OE OE PK LB BE BE GN BN OE OE BE BE WE WE GND STKSW 5V 5V 5V SRHPSW DUPESW GND GND DUPPCSW DUPRSW 5V 5V GND GND SET SIG GND
WE C6517 WE C6516 WE C6515 WE C6514 WE C6513 WE C6512 WE C6511 WE C6510 WE C659 WE C658 WE C657 WE C656 WE C655 WE C654 WE C653 WE C652 WE C651
Wire color BLACK BROWN YELLOW GREEN BLUE WHITE PINK RED ORANGE LIGHT BLUE PURPLE GRAY GREEN/YELLOW
C60(CN8A)
C147 C149
C86
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 2 1 4 3 6 5 8 7 10 9 12 11 14 13 16 15 18 17 20 19 22 21
C19(CN1)
G(5 V) PLSWU G(5 V) PLSWL
C18 (CN2)
C17 (CN3)
A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1
A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11
LSU
R24 V G(24 V) 1 2 RD BE 1 2 RD BE
Mark BK BN YW GN BE WE PK RD OE LB PE GY GN/YW
C51 (CN7)
C148
BE C45B2 LB C45B3 OE C45B4 YW C45B9 RD C45B12 PK C45B11 BE C45B10 BE C45B6 BE C45B5 GN C45B7 RD C45B8 PK C45A12 BE C45A11 GN C45A10 OE C45A9 BN C45A7 BN C45A8 BK C45A5 BK C45A6 RD C45A3 LB C45A4 RD C45A1 BK C45A2
PCM
PFSW4
C22
R24 V R24 V G(24 V) G(24 V) G(5 V) 5V PCM REM PCM LOCK PCM CLK
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 GN 24
1 10 2 9 3 8 4 7 5 6 6 5 7 4 8 3 9 2 10 1
C61(CN5B)
C85
C50 (CN21)
F
COM LIVE G(5 V) DECK TD G(5 V) DECK RD 24 V 5V G(24 V) G(5 V) GN 1 F.G.
C24
WE C751 WE C752 WE C753 WE C754 WE C755 WE C756 WE C757 WE C758 WE C759 WE C7510 WE C7511 WE C7512 WE C7513
GND TLS 5V TRM TRM + TFM TFM + R24 V IFFM REM R24 V CL C. EARTH PK PK PK BN BN BK BK RD BK RD BK GN GND TLDS 5V TNS CONT R24 V TNS SIG GND YW YW YW GN RD PK BE
R24 V G(24 V) ST ALM SC CONT SC REM TC CONT TC REM DB CONT G(5 V) DB REM MC ALM GRID CONT MC REM
1 2 3 4 5 6
16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
PK C477 WE C478 GY C4710 BK C4711 BN C4712 PE C479 BK C1682 WE C1681 BW C473 YW C474 BE C475 GN C476 RD C4717 OE C472 BE C4718 BE C471
LCD
C23(CN1)
P8
C172
C151
G(24 V) 1
C77
4 3 2 1 BE C1613
BK BK BK BK
C48 (CN18)
C76
1 2 3
C82
C81
1 2
BK BK
1 2 3
BK BK
C78
4 3 2 1 2 1
RD BE
1 2 3 4 5 6 7 8 9 10 11 12
1 2 3 4 5 6 7 8 9 10 11 12 13 14
YW YW YW YW YW YW YW YW YW YW YW YW YW YW
1 2 3 4 5 6 7 8 9 10 11 12 13 14
C84
C62(CN5A)
Cleaning earth
C153
TLDS
C80
1 2 3
TFM
TRM
C83
9 8 7 6 5 4 3 2 1
PCM CLK PCM LOCK PCM REM 5V G(5 V) G(24 V) G(24 V) R24 V R24 V
C25(CN5)
24 V 5.1V G(5 V) G(24 V)
4 3 2 1
CL
3 2 1
RD BK
Finisher (Option)
10 9 8 7 6 5 4 3 2 1
BK C4611 RD C4612 LB C465 BE C466 BE C464 GN C463 BE C462 YW C461 RE C467 RD C468
TNS
C27
TLS
C47 (CN17)
C63(CN11)
IFFM
C154
G
C168
BK WE W2 2 WE BK W1 1
8 7 6 5 4 3 2 1
9 8 7 6 5 4 3 2 1
1 2 3 4 5 6 7 8 9
PFM CLK PFM LOCK PFM REM 5V G(5 V) G(24 V) G(24 V) R24 V R24 V
BE C1491 OE C1493 BE C1498 YW C1497 BE C1496 GN C1495 PK C14916 WE C14915 PE C14911 GY C14914 BK C14913 BN C14912
C26(CN3)
ORPCB
DB
DIG KEYR1 DIG KEYR2 DIG KEYR3 DIG KEYR4 SCANR1 SCANR2 SCANR3 SCANR4 DIG LEDR1 DIG LEDR2 DIG LEDR3
MC
TC
C171
1
YW
24 V G(24 V)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
RD C1494 BE C1492
C64(CN6)
220240 V
OMPCB
1 2 3 4 5 6 7 8
R24 V REM
RD C1509 BK C15010
1 2 3 4 5 6 7 8 9 10 11 12 13 14
WE BK BK BK BK BK BK BK BK BK BK BK BK BK
1 2 3 4 5 6 7 8 9 10 11 12 13 14
GRID SC
BUZZER 5V
INLET
L
P27
N
P26
C46 (CN16)
C28(CN6)
RD
RD
RD
WE
YW
1 2 3 4 5 6 7 8 9 10 11 12
12 11 10 9 8 7 6 5 4 3 2 1
WE C51 BE C52 PE C53 LB C54 PK C55 WE C56 YW C57 BE C58 BN C59 GN C510 BE C511
PRY
WE P17 BK P16 AC(N) AC(L) AC(N) AC(L) P13 P12
1 2 3 4 5 6 7 8 9 10 11
MMI TH G(5 V) RESET MMI ENG ERROR MMI MMI ERROR ENGACK MMI TD MMI G(5 V) MMI ACK RD MMI G(5 V)
C31
C75(CN1)
HVTPCB
C65(CN9)
C32
WE C1662
WE C717 WE C718
Noise filter
H I J 8
P15 P14
R24 V RELAY
24 V RELAY
P11 P10
RD C674 YW C679
A
RD C645
MC REM GRID CONT MC ALM DB REM GND(5 V) DB CONT TC REM TC CONT SC REM SC CONT ST ALM GND(24 V) R24 V
1 2 3 4 5 6 7 8 9 10 11 12 13
13 12 11 10 9 8 7 6 5 4 3 2 1
WE C61B2 WE C61B3 WE C61B4 WE C61B5 WE C61B6 WE C61B7 WE C61B8 WE C61B9 WE C61B10 WE C61B11 WE C61B12 WE C61B13 WE C61B14
WE C8617 WE C8618 WE C8615 WE C8616 WE C8613 WE C8614 WE C8611 WE C8612 WE C869 WE C8610 WE C867 WE C868 WE C865 WE C866 WE C863 WE C864 WE C861
SET SIG GND GND GND 5V 5V DUPRSW DUPPCSW GND GND DUPESW SRHPSW 5V 5V 5V STKSW GND
BK P18(TB1) 1 LIVE IN WE P19(TB2) 1 NEUTRAL IN BK P20(TB3) 1 LIVE OUT P21(TB4) 1 NEUTRAL OUT C165(CN10) 1 H1 REM 2 H2 REM WE C1403 WE C1404 WE C1401 WE C1402 WE C1443 WE C1444 WE C1441 WE C1442
R24 V CL REM R24 V IFFM REM TRM REM TRM REM+ TFM REM TFM REM+ 5V TLS GND
RD C8522 BK C8523 RD C8520 LB C8521 BK C8518 BK C8519 BN C8516 BN C8517 OE C8515 GN C8514 BE C8513 PK C8512
C30(CN2)
OLPCB
C45 (CN2)
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26
PWSWU DIG0 PWSWU DIG1 PWSWU DIG2 G(5 V) PWSWL DIG0 PWSWL DIG1 PWSWL DIG2 G(5 V)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
WE BK BK BK BK BK BK BK BK BK BK BK BK BK BK BK BK
C156(CN1) C157(CN2)
1 2 3
1 2 3 4 5 BK LB LB
5.1 V 5.1 V 5.1 V E 5.1 V E 5.1 V E 5.1 V E 5.1 V C164(CN9) WE 1 NEUTRAL OUT 2 WE 3 NEUTRAL IN BK P1 BK P2 OE C1548 OE C1705 OE C1706 C163(CN8) 1 LIVE OUT 2 LIVE IN E 5.1 V
1 2 3 4 5 6 7
BE C851 LB C852 OE C853 BE C859 BE C858 GN C8510 RD C8511 YW C854 BE C857 PK C856 RD C855
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
24 V 23 V G(24 V) CNT. VR DIG KEYL1 DIG KEYL2 DIG KEYL3 SCANL1 SCANL2 SCANL3 DID LEDL1 DID LEDL2 DID LEDL3 DID LEDL4 CFL REM 5V 5V
C74 C71
Touch panel
C33(CN4)
C66(CN10)
WE C8717 WE C8718 WE C8715 WE C8716 WE C8713 WE C8714 WE C8711 WE C8712 WE C879 WE C8710
LIVE FTH 5V
SRM B_ SRM A_ SRM B SRM A R24 V R24 V R24 V DUPFWDSOL R24 V SBFSSOL1
1 2 3 4
RD RD
Y2 X1 Y1 X1
1 2 3 4 5 6 7
C44 (CN3A)
PSPCB
TC
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
C158(CN3)
WE 1 2 WE
A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11
A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1
WE C681 WE C682 WE C683 WE C401 WE C402 WE C403 WE C404 WE C405 WE C406 WE C701 WE C702
BK BK
C72
SSW1
E 5.1 V E 5.1 V
P6
G(5 V) G(5 V) G(12 V) G(5 V) G(5 V) G(5 V) G(5 V) G(5 V) G(5 V) G(5 V)
1 2 3 4 5 6 7 8 9 10
BE C23 BE C24 BE C26 BE C252 BE C163 BE C1611 BE C167 BE C169 BE C644 BE C1693
R24 V TC
TH2
C174
C173
1 G(5 V) 2 5V 3 ESW
C73
1 WE
Fixing unit
OE C21 OE C22 OE C1694 BE C1547 BE C1707 BE C1708 E 5.1 V E 5.1 V E 5.1 V G(5 V) G(5 V) G(5 V)
P1 P2 P3 P4 P5
+12V
WE
3 2 1
2 1 1 2
C36
C35
WE
C162(CN7)
FTH
C43 (CN3B)
C67(CN4)
C159 (CN4)
1 2 3 4 5 6 7 8 9 10 11
1 2 3 4 5
MSW
RD C671
RD C676
WE C4311 WE C4310
H2
H1
1 2 3 4 5 6 7 8 9 10
SSW1 SSW2 SSW3 PRY SOURCE 24 V SSW1 SOURCE SSW2 SSW3 SOURCE PRY REM MSW OFF REM
R24 V TC R24 V CFM1 REM R24 V CFM2 REM 5V FTH ESW 5V GND
B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 B11
B11 B10 B9 B8 B7 B6 B5 B4 B3 B2 B1
WE C361 WE C362 WE C371 WE C372 WE C381 WE C382 WE C741 WE C742 WE C743 WE C744 WE C745
ESW
C160 (CN5)
24 V 24 V
1 2 3 4 5 6 7
1 2 3 4 5 6 7
C161(CN6)
RD C1701 RD C1702
C69
G(5 V) 1 5V 2 SBSW 3
C68
C41
SBSW
CFM2
CFM1
C40
BK RD
CFM2 REM
1 2 R24 V 2 1
WE C436 WE C437
WE C438 WE C439
SSW2
C38
C37
Feedshift unit
(Service part)
W2
WE BK
2 1
FSSOL FSSW
WE C12 BE C11 WE BK
P7
4 3 2 1
G(5 V) 1 5V 2 FSSW 3
PE BK RD BE OE YW WE P21 BK P3
1 2 3 4 5 6
6 5 4 3 2 1
ESCL
CH
WE C1682 BK C1681
W1
C167
BK R24 V BK ESCL
C70 WE C44A2
2 1 WE C44A1 1 2
C42
HSW
C166
2AD
3-7-51
A E
1999 MITA INDUSTRIAL CO., LTD. MITA and are registered trademarks of MITA INDUSTRIAL CO., LTD. Printed in U.S.A.