Documente Academic
Documente Profesional
Documente Cultură
TAMPER SWITCH
FPS-2-2M SPECIFICATIONS
Audio assessment Power requirement Audio information from transducer cable is provided and multiplex switched to isolated audio bus + 12.0 to 16.0 volts DC, 30 mA, Ripple 0.5 Vpp Can be provided by MX-1000 Control Unit, or PPi Uninterruptible Power Supply UPS-PFI
FPS-2-2R SPECIFICATIONS
Alarm/Tamper outputs Relay interface card features: Isolated and supervised relay contacts - plug programmable Normally open or normally closed contacts with 0.5 ampere rating - plug programmable Alarm pulse width Audio assessment Power requirement Adjustable from 0.5 sec. to 2.5 sec Audio information from transducer cable is provided at isolated audio terminals + 11.0 to 16.0 volts DC, 30 mA, Ripple 0.5 Vpp Can be provided by PPi Uninterruptible Power Supply UPS-PFI
Helisensor
Ruggedized Transducer Sensor Cable
Armored Sensor Cable Protects from Physical Damage and Vandalism Easy To Install
The Helisensor is the electret transducer sensor cable encased in a 3/8 flexible metallic jacket, designed for use with the PPi FPS series of signal processors. The Helisensor has been designed to be utilized in demanding areas where vandalism may be a problem or industrial sites where physical damage can occur. Helisensor is available in 100 meter (328 feet) lengths. These sections can be coupled together for longer zones up to 300 meters each. Special hardware is included for end-ofline terminations and splicing together. Helisensor can be installed on standard chain link fencing using outdoor plastic cable ties provided or with optional stainless steel ties. A minimum bend radius of less than 3 inches provides for service loops and sensitivity enhancing arrangements.
HELISENSOR SPECIFICATIONS
Outside diameter Connection/Attachment Supervision 0.56 Inches Conduit fitting on Processor Enclosure / Ultraviolet resistant cable ties furnished with cable Constant impedance monitoring (EOL Condulet furnished with cable)
Telegate
Telescoping Sensor Cable Retractor
Eliminates Disconnect Devices on Gates Simple to Install, Easy to Use, Maintenance Free Eliminates Need for Additional Sensors at Sliding Gate
The Telegate unit provides a connection between the moving transducer on the gate and the fixed transducer on the fence. This eliminates the need for failure prone connect/ disconnect arrangements on the gate. The Telegate consists of a set of weights, aircraft grade pulleys and corrosion resistant armored coax cable encased in a compact, trouble-free PVC tube. The Telegate enclosure is 8 feet high and attaches to a post positioned next to the gate. The Telegate cable automatically retracts and is stored inside the case while the gate is open. As the gate closes, the cable extends, as needed, until the gate is secure. The Telegate, tested in harsh environments, has years of maintenance and trouble free application in all weather conditions.
TELEGATE SPECIFICATIONS
Gate type/ Length Height/ Weight Enclosure Manual or automatic sliding type/ Length up to 30 feet 8 feet/ 65 pounds PVC 6 inch diameter Gate attachment Mounting hardware Thimble and shackle Stainless steel bands (included)
Monitor III
Dual Zone Monitor and Portable Test Unit
The Monitor Series III is a complete dual zone monitor and portable field test unit which may be utilized with all PPi outdoor sensors and provides complete test and annunciation functions. The Monitor Series III indicates Secure, Alarm, Tamper, and Access conditions from the sensors by illumination of LED indicators and by an audible tone generated upon alarm. Audio listen-in capabilities are also available. LED indicators are present for display of communications failure in multiplex systems and an auxiliary alarm indicator. The Monitor Series III is powered by an 18 VAC Class II plug-in transformer which supplies power for continuous operation of the monitor and for continuous charging of the internal batteries allowing a minimum of 4 hours of standby power. The monitor is designed to supply the required DC voltage for powering the connected sensors.
Perimeter Products inc., 1130 Terra Bella Avenue, Mountain View, California 94043 Telephone: (650) 966-8550 Fax: (650) 966-8517
1996 Perimeter Products, Inc. All Rights Reserved Note: Specifications Subject to Change without Notice.
REV 2/96